Ganz ZN1A-4D6DTMZ67 User Manual
Advertisement
Advertisement
Ganz GXi Series VCA Interface Manual v1.0.66
20MP 360° Surround View IP Camera with Video Analytics
ZN1A-4D6DTMZ67
User
Manua
l
Ver. 1.0 / 2021.04
Before connecting, operating or adjusting this product, read this instruction booklet carefully and completely
ganzsecurity.com
Contents
NETWORK SETUP
03 IP Installer
04 Quick Start of Network Connection
05 DDNS Registration
06 Guide to Network Environment
07 Setup Case (A~D)
09 Port Forwarding
10 Starting IP Camera
WEB VIEWER SCREEN
11 Basic Screen
SETUP
13 Video & Audio Setup
21 Camera Setup
30 Network Setup
40 Trigger Action Setup
44 Event Setup
50 Record Setup
56 Security Setup
63 System Setup
APPENDIX
74 A : Current TCP/IP Settings
75 B : Changing IP address and subnet mask
76 C : Port Forwarding
78 FAQ
2
Network Setup -
IP Installer
1. Run IP Installer
1 Run the IP installer.
2 Click on Network Adaptor selection Menu (NIC) after run this program.
3 Select a network which a camera is connected then click on a ‘Search’ button. (Takes about 5 sec.)
4 Select a camera to set.
5 The information of the selected camera will be shown at
Device Info.
6 Select the network type.
i The default network type of the camera is STATIC.
i When set to DHCP, if you have a DHCP server, it will
automatically set the Camera IP.
i When set to DHCP, if you have do not have a DHCP server,
Camera IP is set to 192.168.xxx.xxx after one minute.
7 Convert the devide's MAC address to the IP address.
MAC address = 00-13-23-01-14-B1
IP address = 192.168.20.177
i Covert the last two sets of hexadecimal number to decimal number.
Input IP setting information when the network type is set to STATIC.
i Default TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
8 Change the port as necessary when the network type is set to STATIC.
i A ‘Port Forwarding’ has to be set for external access
to the camera.
i Refer to the manual of the network hub for
‘Port Forwarding’ settings.
i An additional change of HTTPS, RTSP port can be done at Web Viewer >Setup page.
9 Input ID and PW of the camera for authentication.
Make sure to change the ID and PW for security reason.
Go to “Web viewer>Setup>System>Users Management” for ID and PW change.
The ID and PW will be set to default value when ‘factory reset’ the camera.
i Default ID / PW : root / pass
10 Make sure to click on ‘Save’ button to save changed values.
An “Apply” message will be popped-up when the settings are applied normally, or an error message will be popped-up when failed.
11 To reboot or reset (except network setting) the camera.
Select a camera (multiple camera can be selected) >
Input ID and PW > Click on Reboot or Factory Reset button.
12 Able to delete an Active-X which is installed when accessing to Web Viewer.
You don’t need the function because this camera use the
VLC plug-in instead of the Active-X.
3
Network Setup -
Quick Start of Network Connection
Please follow the steps below to complete the initial setup of the network function.
i i Please do not power on the IP Camera until instructed.
Temporarily disable any proxy servers configured in i If connecting the IP Camera directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP Camera and the IP Camera has been correctly connected to the modem.
1 Connect the IP Camera and PC to the configured network.
2 Open the IP Installer on a PC, then search for the
IP camera.
i The default network type of the camera is STATIC.
i When set to DHCP, if you have a DHCP server,
it will automatically set the Camera IP.
i When set to DHCP, if you have do not have a DHCP
server, Camera IP is set to 192.168.xxx.xxx after
one minute.
3 If multiple numbers of camera are connected it should be distinguished by the mac address of the Camera.
4 Click the Camera IP, and connect to the WEB PAGE.
5 Default ID/Password to access IP Camera are both the word: root / pass.
6 Familiarize yourself with the Viewer Interface Screen.
7 Please install VLC to display live video.
8 The IP setting can be set to ‘STATIC’ at IP Installer or web viewer followed by Setup -> Network -> Network Settings
9 If the IP Camera is connected to a network which utilizes a router, you must have Port Forwarding configured on your personal router to forward all ports to the IP address you have assigned the IP Camera.
10 After configuring Port Forwarding on your router
(if necessary), you may access your IP Camera on your local network by opening Internet Explorer and specifying the IP address and Web Port that you have assigned to the IP
Camera.
i i Example: http://192.168.0.200:8888
If you leave your Web Port set to 80, you don’t need to specify the port in the Address Bar to access to your
11 Access your IP Camera via the Internet :
If you use a static IP address assigned by your ISP
1) Open Internet Explorer.
2) Type the IP of the IP Camera.
3) If you use a router, type the routers’ static IP and the web port number of the IP Camera.
If you have a dynamic address provided by your ISP
1) Open Internet Explorer and visit the DDNS website.
2) Register the IP Camera.
3) Reboot the IP Camera.
4) Give the DDNS server 10 minutes to locate your IP
Camera’s IP information.
5) Click the refresh button in the Internet Explore.
6) After your camera is connected, select your camera.
4
Network Setup -
DDNS Registration
If you have DYNAMIC IP service from your
Internet Service Provider (ISP), you can’t tell the current IP address of the IP Camera.
To solve this problem, you have to register to our DDNS service.
At first, you have to check if you are using dynamic addressing. If so, register your IP
Video Server on our DDNS website before you configure, setup, or install the IP Camera.
Even though your IP is not dynamic, you will get benefit if you register to DDNS. In this case, just remember ‘hostname.dyndns.
com/gate1’ instead of complicated series of numbers like http://201.23.4.76:8078.
For more details, contact our Support Center.
To use a public DDNS called ‘dyndns’ or ‘no-ip’, refer to the detail information on how to use the service.
(Visit the web site : http://www.dyndns.com or http://www.no-ip.com)
5
Network Setup -
Guide to Network Environment
Please configure the IP Camera at the installation site. You must determine your network scenario in order to configure the IP
Camera with the proper TCP/IP settings.
This tutorial will guide you through the process. Before actually configuring the IP
Camera, determine settings to be applied.
Record those settings to be used to configure your IP Camera for reference.
When configuring your IP Camera, treat the
IP Camera as another PC on your network.
You will assign it several addresses and other
TCP/IP properties to match your current network.
This step-by-step tutorial will teach what IP addresses and network configurations should be assigned based on the network scenario.
1 Before you begin, locate any information and settings received from your Internet Service Provider (ISP).
You may need to refer to these IP addresses at a later time during the configuration.
Current TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server (Option)
Static □ Dynamic □ i If you were not given any IP addresses or the ISP was responsible for the setup and installation of your
Internet connection, go to step 2.
i If you are not using a router on your network, your ‘Current TCP/IP Settings’ (from the previous section) and ‘Assigned IP Addresses from My ISP’ will be exactly the same.
2 You must determine whether the IP address is STATIC or
DYNAMIC. At this moment, you are only concerned about the ISP. Did they provide you with a STATIC or DYNAMIC address? If you are unsure, contact your ISP.
3 Configure your IP Camera’s TCP/IP settings for network connectivity by selecting Setup from the main interface and selecting TCP/IP located on the left of the
Setup screen.
4
If prompted for ID and Password, use ‘ root / pass ’ for both entries. The default web port number is 80. If port 80 is blocked by the ISP, a value between 1025 ~ 60000 should be used. If TCP port 80 is blocked, consult the ISP.
5 The following descriptions are several basic network scenarios. Determine which scenario describes your network. If your network does not match one of the scenarios below and you are unsure how to setup your IP
Camera, contact your network administrator and then call our Support Center.
i You cannot control the rectangular gray areas and only the ISP has access to the devices.
6
Network Setup -
Setup Case A, B
Case A:
Dynamic IP + Personal Router [Most SOHO]
Internet
Camera
Phone Line or CATV
Cable/xDSL Modem
(ISP Provided)
Personal Router
W/Integrated Switch
PC
Case B:
Static(Fixed) IP + Personal Router [Efficient]
Internet
Camera
Public Line
Gateway or Router at ISP
Personal Router
W/Integrated Switch
PC
Configure your IP Camera’s TCP/IP properties as follows :
1 Network Type : STATIC (even though you have Dynamic IP from your ISP, use STATIC on the IP Camera)
2 Internet Address : A private IP address such as
192.168.0.200 (Example) i You need to assign an IP address to the IP Camera just
as you do with PC.
i The IP address you assign must be unique to your network and match your network as well.
For information on how to choose a unique IP and match your network, read the FAQ.
i The IP address you assign must be a private IP.
For information on how to choose a private IP please, read the FAQ.
3 Subnet Mask : 255.255.255.0 (Example) i
You must use the same subnet mask as the one you noted under ‘Current TCP/IP Settings’.
4 Default Gateway : 192.168.0.1 (Example) i This IP address must be the IP address of your router.
(private or LAN side) i Use the same Default Gateway you noted under
‘Current TCP/IP Settings’.
5 Preferred DNS Server : Use the 1st DNS Server from
‘Assigned IP Address from My ISP’.
i If you did not receive any IP addresses from your ISP, contact the ISP and acquire the IP address of their
6 DDNS Server : Use the DDNS server.
i This is the same site you will register later to accommodate dynamic IP from your ISP.
7 Web Port : 8888 i Do not use the default port 80 as this number must be
changed. i You may select any number between 1025 ~ 60000.
7
Network Setup -
Setup Case C, D
Case C:
Static(Fixed) IP
[Dedicated line directly to the IP Camera]
Case D:
Dynamic IP + DSL/Cable Modem
[Connected directly to the IP Camera]
Camera Camera
Internet
Phone Line or CATV
Cable/xDSL Modem
(ISP Provided)
Configure your IP Camera’s TCP/IP properties as follows :
1 Network Type : STATIC
2 Internet Address : A static IP address received from your
ISP such as 24.107.88.125 (Example) i You need to assign an IP address to the IP Camera just as you do with PC.
3 Subnet Mask : Subnet mask assigned from your ISP such as 255.255.255.240 (Example)
4 Default Gateway : 24.107.88.113 (Example) i Use the assigned default gateway from your ISP.
5 Preferred DNS Server : Use the 1st DNS Server from
‘Assigned IP Address from My ISP’ i If you have not received any IP addresses from your
ISP, contact them to acquire the IP address of their
6 DDNS Server : Use the DDNS server i This is the same site you will register later to utilize our DDNS service.
7 Web Port : 80 i You may select any number between 1025 ~ 60000.
Gateway or Router at ISP
Public Line
Internet i To connect the IP Camera directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP Camera and the IP Camera has been connected correctly to the modem. Then power on the modem, followed by the IP Camera.
Configure your IP Camera’s TCP/IP properties as follows :
1 Network Type : DYNAMIC
2 DDNS Server : Use the DDNS server i This is the same site you will register later to accommodate dynamic IP from your ISP.
3 Web Port : 80 i You may select any number between 1025 ~ 60000.
8
Network Setup -
Port Forwarding
After entering the correct TCP/IP settings, you are ready for ‘Port Forwarding’
(Cases A, B).
1 Please record the TCP/IP settings of your IP Camera for
future reference. You may need this information to access
your IP Camera and to configure ‘Port Forwarding’.
IP Camera TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
DDNS Server
Web Port
2 After clicking ‘Apply’, the system will prompt for reboot.
Please allow the system 50 seconds to reboot and accept
the changes. After 50 seconds, close the configuration
screen. The view will display ‘Trying to Reconnect’.
If the ACTIVE light on the IP Camera has gone off and is
now back on again flashing, the IP Camera has rebooted.
After the system reboots completely, remove the power
supply from the unit and close Internet Explorer.
3 Return your PC/Laptop TCP/IP properties to their original
settings.
4 Before installing the IP Camera, you must use
‘Port Forwarding’ on your personal router (Cases A, B).
You will need to forward 1 ports:
· Web Port
All the ports will be forwarded to the IP address you
assigned to the IP Camera.
In the example above, you would forward:
· 8888 > 192.168.0.200
i For information on how to use ‘Port Forwarding’,
please read Appendix C.
9
Network Setup -
Starting IP Camera
After forwarding correctly the Web Port, through your router (if applicable), install the
IP Camera in a proper location.
1 Locate the serial number located on the label attached to the bottom of the IP Camera, you will need this for DDNS
registration.
2 Connect the IP Camera to your router or cable/DSL modem
(per your network scenario) via a Cat5/5e UTP Ethernet network cable.
3 Supply power to the IP Camera.
4 After 1 minute, verify the IP Camera indicators:
· LINK : Flickering/Solid
5 After configuring Port Forwarding on your computer
(if necessary), access your IP Camera on your local network by opening Internet Explorer and specifying the IP address and Web Port assigned to the IP Camera. i Examples: http://192.168.0.200:8888 or
http://24.106.88.123 i If you left your Web Port set to 80, do not need to specify the port in the Address Bar to access the
6 Access your IP Camera via the Internet :
If you use Case B, C
1) Open Internet Explorer.
2) Type the IP of the IP Camera.
If you use Case A, D
1) Open Internet Explorer.
2) Visit the DDNS website.
3) Register the IP Camera.
4) Give the DDNS server 10 minutes (MAX) to locate your
IP Camera’s IP information. You may reboot the server to send an immediate request to our DDNS server.
5) After your camera is connected, select your camera.
i The difference between B and C is that B needs to
set the port forwarding.
i Since the type of DDNS differs from the service type, refer to the related service site.
10
Web Viewer Screen -
Basic Screen (Default)
Password change is required at initial connection in factory reset state.
1 You can not see the image, and the Setup button is disabled.
2 Change the password with the CHANGE PASSWORD button.
3 After changing the password, you must log in again by pressing the RE-LOGIN button.
Web index In the state of the page, when the web page does not have a mouse click or keyboard input event, the web session
it will close and automatically switch to the log out page. (You must log in again with the RE-LOGIN button.)
4 Click ‘LOGOUT’ to log out.
11
2
3
4
5
6
Web Viewer Screen -
Basic Screen
1
Web viewer is optimized with explorer10 or above version and Firefox.
If VLC is not installed or VLC plugin is not supported (Chrome), Live buffering and Channel select menu on 3, 4 will be changed to Live Viewer menu, and then if HTML5(MJPEG) is selected on Live Viewer menu, then you can check the video.
1 Live video display. This is the region for live video stream from the camera.
2 Setup popup button. Click it to open the Setup page to setup details of IP camera like Video, Network, Events, System and etc.
See the section ‘Setup’ .
3 Select Viewer. Click it to open Viewer separately and Viewer at once.
4 Channel Select button. Select a stream produced from the camera between Stream 1 ~ 3 to display it in the live view screen.
Refer the ‘Setup > Video & Audio > Video’ to setup the Video Stream.
If you select Viewer 1 to Viewer 4, Channelselect button is activated.
5 When the image goes unsmoothly because of bad network connection, it stored image during setup time and shows the image on the live view screen.
User will see the delayed images as much as setup time.
6 Below “Menu” is supported in accordance with models.
PTZ Control This camera model does not support the zoom and focus.
Preset Does not support.
Speaker Control Enable/Disable Audio stream received from the camera and Volume control of the speaker in the Computer.
Alarm Input If the alarm is triggered, the color of corresponding input number will be changed to red from dark gray.
Relay Out Using these Checkbox, you can read status of Relay Out and also set or reset it manually.
7 Motion It shows the Motion event status.
Event Alert Icon ( ) appears if ‘Motion Detection’ is activated.
8 Camera Time Display the camera time.
12
7
8
Setup - Video & Audio Setup
Video Configuration
1
2
1 Detail Page - When you selects an item from the menu, you can set the details for the selected item.
2 Setup Constitution
Video&Audio
[ VIDEO, OSD, ROI, AUDIO, PRIVACY MASK ]
Camera
[ MFZ, PROFILE, IMAGE ADJUSTMENT, EXPOSURE, DAY&NIGHT, BACKLIGHT, WHITE BALANCE, IMAGE, VIDEO ]
Network
[ STATUS, NETWORK SETTING, AUTO IP, ONVIF, UPNP, DDNS, FTP, SMTP, SNMP, RTSP INFORMATION ]
Trigger Action
[ ACTION RULES, IMAGE TRANSFER, RELAY OUT ]
Events
[ EVENT RULES, SCHEDULE, MOTION, TEMPERATURE, ALARM ]
Record
[ MANAGEMENT, RECORD LIST, STORAGE ]
Security
[ IP ADDRESS FILTER, RTSP AUTHENTICATION, IEEE 802.1x, HTTPS, CERTIFICATES, SERVICE ]
System
[ INFORMATION, DIAGNOSTICS, FIRMWARE UPDATE, DATE&TIME, DST, USER MANAGEMENT, LOG, LANGUAGE, FACTORY RESET,
RESTART, OPEN SOURCE ]
13
Setup - Video & Audio Setup
Video Configuration
1
2
3
4
5
6
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Apply' to set the other video setting.
2 Live Video Channel Setup The video can be configured to variety settings with a combination of codec and resolution.
The camera performance has to be considered when setting multiple channels. This effects on the performance of the camera.
H.265 (HEVC) codec with higher bitrate may cause the unstable live streaming or reloa d the webpage.
3 Codec - Choose the video codec. According to the selected codec, the subcategories can be changed automatically.
4 Description Input the additional description about the selected channel. Max. 30 alphabets are allowed (Including space).
For the description, English Alphabets, numbers and special characters ( - _ @ . ) can be used.
5 Resolution Select the video resolution.
Available resolution can be depends on the codec setup between the channels.
<Resolution of Video Format>
QFHD
2560x1440
(4M)
1080p/i 720p/i SVGA
768x432
(0.3M)
4CIF
3840x2160 2560x1440 1920x1080 1280x720 800x600 768x432
704x576
704x480
6 Frame Rate Select the maximum Frame Rate.
Available Frame Rate can be different although same codecs were set up.
VGA
640x360
(0.2M)
640x480 640x360
CIF
352x288
352x240
14
Setup - Video & Audio Setup
Video Configuration
7
8
9
7 GOP(Group of Pictures) Size Set up the number of frames (P-frame) which contain only changed information based on basic frame (I-frame). Regarding videos with lots of movement, if you set GOP size bigger, only the number of P-frames is bigger.
As a result, video resolution will be low but ‘File size’ and ‘Bit-rate can be decreased.
GOP(Group of Pictures) Size is..
I-frame and P-frame can be created for MPEG4, H.264 and H.265 (HEVC) video compression. I-frame(=key-
frame) means the whole image data for one specific scene of video. P-frame is image data which has been changed information compared to I-frame GOP is made up of one I-frame and corresponding several P-frames. To improve video quality, set the number of P-frames smaller and to decrease image size, set the number of P-frames bigger.
8 Profile The profile defines the subset of bit stream features in H.264, H.265 (HEVC) stream, including color reproduction and additional video compression.
H.264 : Main, High / H.265 (HEVC) : Main
Main An intermediate profile with a medium compression ratio. The main profile supports I-frames, P-frames, and B-frames.
High A complex profile with a high compression ratio. The high profile supports I-frames, P-frames, and B-frames.
9 Bitrate Mode Select the bit rate control scheme of video compression from CBR (Constant Bit Rate) or VBR (Variable Bit Rate).
CBR To guarantee the designated constant bit rate, the quality of video are controlled in this mode.
Therefore, the quality of video is likely to be varying when network traffic is changing.
VBR To guarantee the designated quality, the bit rate of video stream is changed in this mode.
Therefore, the frame rate of video is likely to be varying when network traffic is changing.
This category won't be appear if you select the codec.
15
Setup - Video & Audio Setup
Video Configuration
10
11
12
13
14
10 Target Bitrate If Bitrate Control is set to be CBR, you can set the Target Bitrate.
11 Quality For VBR control mode, The Target Quality of video can be setup.
12 Smart Bitrate Control
Off You can not use the Smart Bitrate Control function.
CVBR (Framerate priority) This Mode is for cameras which do not want absolute any frame drop, but still want to get lower bitrate. It has limitation when the Target bitrate is set to be very low, but actual motion is big or scene is very noisy.
CVBR (Quality priority) When the Target bitrate is set to very low, and motion is big, then LBR will try to drop frames, and make the final fps to be lower, so that it can save its and make the output frames to have better quality.
CBR This Mode is a CBR alike mode which is close to traditional security IPCAM, and it's not designed for LBR,
It's provided as an option in LBR library just to help comparison.
13 Extension Option
Off You can not use the Extension Option.
SVC-T On The H.264, H.265 (HEVC) SVC (Scalable Video Coding) is a video compression algorithm that enables effective and efficient transmission of video files over low bandwidth networks.
14 Click ‘Apply’ to make above setting effective.
Click 'Apply All' to set all video setting.
16
Setup - Video & Audio Setup
OSD Configuration
1
2
3
4
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Apply' to set the other video setting.
2 Date / Time - Display the current time.
3 User Text - Output the TEXT entered by the user. Support a maximum of 30 characters.
4 Click ‘Apply’ to make above setting effective.
17
Setup - Video & Audio Setup
Region of Interest Configuration
3
4
1
2
5
Region of interest function gives much more efficiency picture quality for indicated area to improve picture qualities of movement scene at the same bandwidth.
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Stream Select the Stream.
Currently it supports only H.264, H.265 (HEVC).
The function is not supported in MJPEG codec.
3 Activation The Region of interest can be enable or disable.
4 Quality Set the quality of the set area.
5 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
18
Setup - Video & Audio Setup
Audio Configuration
1
2
3
4
1 Codec Select the Audio Codec.
Currently it supports only codec G.711.
2 Volume - Select the Audio Volume from 0 to 10.
3 Sample Rate Select the Audio Sample Rate.
Currently it supports only 8000 Hz.
4 Click ‘Save’ to make above setting effective.
19
Setup - Video & Audio Setup
Privacy Mask Configuration
1
2
3
4
Use this function to mask areas that you want to hide on screen to protect privacy.
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Activation The Privacy mask function can be enable or disable.
3 Area Select the Area1 ~ Area16 and Set the privacy area.
4 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click ‘Clear Area' to delete the selected Area1~Area16.
20
Setup - Camera Setup
MFZ Configuration
1
2
3
1 Zoom & Focus You can zoom OUT (-) or zoom IN (+) and focus OUT (-) or focus IN (+).
Focus button (-) / (+) is activated in Manual mode.
2 Zoom Speed Set the speed of zoom and focus. (1~3)
3 Auto & Manual - Click the button to switch focus mode (Auto / Manual).
Auto mode - Auto focus is activated after zoom button (-) / (+) action. After auto button action, auto focus is activated once
and focus button (-) / (+) is deactivation.
Manual mode - You can manually adjust the focus position. Focus button (-) / (+) is activated.
21
Setup - Camera Setup
Profile Configuration
1
2
1 Profile List Display the information in profile list.
2 Click ‘Add’ to add the profile stored the current camera settings.
Click ‘Delete' to delete selected item from the profile list.
Click ‘Apply' to apply selected item from the profile list.
22
Setup - Camera Setup
Camera Image Adjustment
1
2
3
4
5
6
7
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Sharpness Using this control, sharpness of image can be adjusted to meet your preference.
3 Brightness Using this control, brightness of image can be adjusted to meet your preference.
4 Contrast - Using this control, contrast of image can be adjusted to meet your preference.
5 Saturation - Using this control, Saturation of image can be adjusted to meet your preference.
6 Hue Using this control, Hue of image can be adjusted to meet your preference.
7 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
23
Setup - Camera Setup
Camera Exposure Settings
1
4
5
2
3
6
7
8
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Auto Exposure - Automatic exposure(AE) automatically sets the aperture or shutter speed, based on the external lighting
conditions for the photo.
3 Exposure Level If this value is increases, the image becomes brighter.
4 AE metering AE metering mode refers to the way in which a camera determines the exposure.
5 Shutter Speed If this speed is faster, the moving object can be photographed without the ghost effect.
However, picture can be dark if there is no sufficient lighting.
6 Slow Shutter Level Slow shutter Level lets you adjust the amount of light striking the sensor, and essentially determines
when the video sensor sends out its batch of data for processing.
7 Gain Limit - The smaller number makes the darker image.
8 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
24
Setup - Camera Setup
Camera Day & Night Settings
1
4
5
6
2
3
7
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Day & Night
- Auto: In this mode, the IR cut filter is removed automatically depending on the light condition around.
- Day: In this mode, the IR cut filter is applied to the image sensor all the time.
Thus, the sensitivity will be reduced in the dark light condition but the better color reproduction performance are obtained.
- Night: In this mode, the IR cut filter on the image sensor is removed all the time.
The sensitivity will be enhanced in the dark light condition but the image is black and white.
3 Color Level It is a level to change Night mode into Day mode when Day & Night mode is Auto.
4 B / W Level - It is a level to change Day mode into Night mode when Day & Night mode is Auto.
5 Transition Time If it is set to Auto, to determine the rate at which Day / Night is converted.
6 IR Mode The IR function can be enable or disable.
7 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
25
Setup - Camera Setup
Camera Backlight Settings
2
3
This is a feature used for problematic light conditions where the contrast from light to dark areas is very high.
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 WDR (Wide Dynamic Range) The WDR function can be enable or disable.
3 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
1
26
Setup - Camera Setup
Camera White Balance
2
3
4
5
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Activation White Balance can be enable or disable.
3 White Balance Mode Select White Balance depending on the lighting conditions.
4 RGB Gain The R/G/B gain can be set only when the White Balance Mode is set to Manual.
5 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
1
27
Setup - Camera Setup
Camera Image Enhancement
1
2
3
4
5
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 3D Noise Reduction 3DNR function enables to suppress noise and retain good video quality in low light conditions.
3 Mirror - Reverse the video from side to side.
4 Flip Reverse the video from up to down.
5 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
28
Setup - Camera Setup
Video Enhancement
2
3
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
2 Flicker This function Enable to enhance the flicker situation.
3 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
Click 'Default' to settings to the factory defaults.
1
29
Setup - Network Setup
Network Status
This menu will show you all the information of Network setting in the camera. However, you cannot change those here.
30
Setup - Network Setup
Network Settings
1
7
8
9
10
2
3
4
5
6
1 Network Type Define network IP address type from the Static Mode for the fixed IP or the Dynamic Mode by the dynamic
IP address.
If you select the Static Mode, you must fill out IP Address, Subnet Mask, Gateway, DNS Server and all ports.
If you select the Dynamic Mode, the IP address will be allocated automatically by DHCP equipment.
If you click the Apply button to update changes, the system will be re-booted.
In this case, you have to reconnect the camera using new IP address.
2 IP Address Define the IP address. The address is consisted of four numbers separated by dots and the range of each number is from 0 to 255.
3 Subnet Mask Define the Subnet Mask. Format is same as the IP address.
4 Default Gateway Default the Gateway IP Address. Format is same as the IP address.
5 Preferred DNS Server Define the DNS server IP address. Format is same as the IP address.
6 Alternate DNS Server Define the Secondary DNS server IP address. Format is same as the IP address.
7 HTTP Port - The HTTP port can be set to 80 which default or in between 1025 to 60000.
8 HTTPS Port - The HTTPS port can be set to 443 which default or in between1025 to 60000.
9 RTSP Port The RTSP port can be set to 554 which default or in between 1025 to 60000.
10 Click ‘Apply’ to make above setting effective.
If the network type is dynamic, the IP address is changed in below cases.
Therefore, the IP address needs to be searched again, and the camera needs to be reconnected in these cases.
- When the camera power is on / off.
- After Firmware update, Default set and reboot.
31
Setup - Network Setup
Auto IP Settings
1
2
3
1 General Setting Auto IP Settings function can be enable or disable.
2 Auto IP Settings Information It displays the unique id or Auto IP address.
3 Click ‘Apply’ to make above setting effective.
32
Setup - Network Setup
ONVIF Settings
1
2
3
1 Authentication
None: Allows to access without ONVIF authentication.
WS - Usertoken: Allows to access with WS-User Token of ONVIF authentication.
WS - Usertoken + Digest: Allows to access with WS-User Token and Digest of ONVIF authentication.
2 Discovery Mode - The discovery function can be enable or disable.
3 Click ‘Apply’ to make above setting effective.
33
Setup - Network Setup
UPNP Settings
1
2
3
1 General Setting - UPNP function can be enable or disable.
2 Friendly Name - Define the friendly name. Support a maximum of 30 characters and special character (/ ~ ! $^ ( ) { } [ ] ; , ) can not be used. ('@', '.', '_' ,'-', ' ') can be used.
3 Click ‘Apply’ to make above setting effective.
34
Setup - Network Setup
DDNS Settings
1
2
3
1 DDNS Disable If it is selected, DDNS service does not work.
2 Public DDNS To use public DDNS service, select a site address listed in the list. After filling out the Host Name of the site, the setup is completed by entering User Name and Password registered in that DDNS site.
DDNS Provider
DynDNS
No-IP
Site Address www.dyndns.com
www.no-ip.com
If you setup DDNS properly, the IP address of your camera will be updated automatically whenever IP address is changed or system is rebooted.
If IP updating to DDNS site is failed, camera will keep retrying in 1min. interval.
3 Click ‘Apply’ to make above setting effective.
35
Setup - Network Setup
FTP Settings
1
4
5
2
3
6
7
To transfer / save the image to the relevant sites through FTP, then FTP needs to be setup.
1 General Setting FTP function can be enable or disable.
2 FTP Server Address Define FTP Server IP Address. If IP Address form is incorrect, a Message box will be shown to try again.
3 FTP Upload Path Define a path in FTP server to store video. For the path name, English Alphabets, numbers and special
characters ( / ~ !@ $ ^ ( ) _ - { } [ ] ; , ) can be used.
4 FTP Port Define the FTP Server Port. If Port is not appropriate, it is impossible to access to FTP Server.
5 User ID Define User ID to access to the FTP Server. Fill out the correct User ID registered in the FTP Server.
6 Password Define Password to access to the FTP Server. Fill out the correct Password registered in the FTP Server.
7 Click ‘Apply’ to make above setting effective.
Refer the above screen image for the example.
36
Setup - Network Setup
SMTP Settings
1
7
8
5
6
2
3
4
9
10
11
To send / save the image to the relevant sites by Email, SMTP needs to be setup.
1 General Setting SMTP function can be enable or disable.
2 Mode Select Security mode of SMTP from Plain or SSL / TLS. After checking account setup of your SMTP Server, you may select one.
3 SMTP Server Address - Define the SMTP Server Address. If the IP Address form is incorrect, a Message box will be shown to try again.
4 Port - Define the Port used in the Plain or SSL / TLS security mode in the above.
5 User ID - Define the User ID to access to SMTP Server. Fill out the correct User ID registered in the SMTP Server.
6 Password Define the Password to access to SMTP Server. Fill out the correct Password registered in the SMTP Server.
7 E-Mail Sender Define the e-mail address of E-Mail Sender. It will be displayed as the sender when the camera sends an E-mail.
8 E-Mail Receiver Define the e-mail address of E-Mail Receiver. It will be displayed as the Receiver when the camera sends an E-mail.
9 Title - Define the title of the E-Mail when the camera sends an E-mail.
The title of the Email is limited to 40 characters including the spaces.
10 Message Define the contents of E-Mail when camera sends an E-mail. The message of the Email is limited to 40 characters including the spaces.
11 Click ‘Apply’ to make above setting effective.
37
Setup - Network Setup
SNMP Settings
1
2
3
6
7
8
4
5
9
1 SNMPv1/SNMPv2 Select the SNMPv1/SNMPv2 option and type the names of Read community and Write community.
SNMP trap can be used to check periodically for operational thresholds or failures that are defined in the MIB.
2 SNMP Trap SNMP trap can be enable or disable.
SNMPv3 contains cryptographic security, a higher security level, which allows you to set the Authentication password and the
Encryption password.
3 Mode Select the either Read or Read/Write mode.
4 Activation - It can be enable or disable selected mode.
5 Read/Write name - Define Read name and Write name.
6 Security Level Select one of no auth, no priv/auth , no priv/auth, priv
7 Authentication Algorithm Select MD5 or SHA as the authentication method.
8 Authentication Password The Authentication Password is an encryption for authentication and they are at least 8 digits and up to 30 digits allowed.
9 Click ‘Apply’ to make above setting effective.
38
Setup - Network Setup
RTSP Information
5
6
7
2
3
4
1 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Apply' to set the other video setting.
2 Target Stream Select the stream you want to set.
3 Time out Set the RTSP time out.
The session is disconnected after the specified time out.
4 QoS Setting Set the quality of service to ensure data transfer performance.
5 RTP Multicast Check RTP Multicast Start/Stop. To activate RTP Multicast.
1. Click “On” button.
2. Enter accessible RTP Multicast IP, port for video stream control, RTP packet TTL.
3. Click “Apply” button.
It is possible to set each RTP Multicast for CH1~3.
6 Click ‘Apply’ to make above setting effective.
Click this button when completed setup each channels.
7 It shows RTSP Connection information.
1
39
Setup - Trigger Action Setup
Action Rules Configuration
1
2
1 Action rules List It indicates the custom action rule information added to Action rules list.
2 Click ‘Add’ to add custom action rules.
Click ‘Modify' to modify selected item from the action rules list.
Click 'Delete' to delete selected item from the action rules list.
40
Setup - Trigger Action Setup
Action Rules Add / Modify
1
2
3
4
1 Name Define name of action rules.
Input text cannot be exceed limited (3~15).
2 Operation Interval Select the interval to maintain action.
3 Action1 ~ Action5 Select the action to take If the event occurs.
4 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous menu.
41
Setup - Trigger Action Setup
Image Transfer Configuration
1
2
1 Pre / Post Alarm Image Image Transfer due to event is configured by setting Image transfer rate and Pre / Post alarm duration.
Number of Image
Pre-alarm Duration
Post-alarm Duration
Descriptions
Define Number of image transferred per second.
Define duration of image transfer before an event.
Define duration of image transfer after an event.
2 Click ‘Apply’ to make above setting effective.
42
Setup - Trigger Action Setup
Relayout Configuration
1
2
3
4
5
1 Relay Output Select the Relay output.
The number of relay outputs depends on the camera model.
2 Mode Select the monostable / bistable for relay mode.
3 Idle State Select whether the contact is normally opened or is closed.
4 Duration Relay out is operated during the setting time.
If monostable mode is selected, this function is activation.
5 Click 'Apply' to make above setting effective.
43
Setup - Event Setup
Event Rules Configuration
1
2
1 Event Rules List It indicates the custom Event Rule information added to Event Rules list.
2 Click ‘Add’ to add custom event rules.
Click ‘Modify' to modify selected item from the event rules list.
Click 'Delete' to delete selected item from the event rules list.
44
Setup - Event Setup
Event Rules Configuration
3
4
5
1
2
6
7
1 Activation The Event Rules function can be enable or disable.
2 Name Define the Event rule name.
3 Event - Select the event among motion detection, network disconnection, illegal login detected, temperature critical, schedule, sensor detection.
Click 'Cancel' to return to the previous setting.
You need a event one more.
4 Schedule - Select activation time from Always / Manual Time.
5 Week / Time You need to define Start time and End time followed by selecting Days. The setup schedule is repeated every week.
6 Rules - Select the action rule defined in the Trigger Action-Action rule menu.
7 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
45
Setup - Event Setup
Schedule Configuration
1
2
3
1 Mode The Schedule function can be enable or disable.
2 Repeat Rule - Set a recurring time the event occurs.
3 Click ‘Apply’ to make above setting effective.
46
Setup - Event Setup
Motion Detection Configuration
1
2
3
4
5
6
1 Motion Detection It shows the Motion event status.
Event Alert Icon ( ) appears if ‘Motion Detection’ is activated.
2 VIN Source Select the Video 1 ~ Video 4 and set the video setup.
Click 'Save' to set the other video setting.
3 Area Set the motion detected area.
You can set up to four areas.
4 Activation Enable or Disable motion detection function.
5 Sensitivity - Define the sensitivity of motion detection.
If High value is selected, it will detect very small motion while it becomes relatively insensitive when Low value is selected.
6 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
47
Setup - Event Setup
Temperature
1
2
3
4
1 Mode Select the either Fahrenheit and Celsius.
2 Threshold Define the temperature at which the event trigger is occurred.
3 Temperature It indicates the current temperature of the IP camera.
4 Click ‘Apply’ to make above setting effective.
48
Setup - Event Setup
Alarm Configuration
1
2
1 Input Device Setup Select input device type from OFF / N.O. / N.C.
OFF
NO
NC
Operation
Ignore this input sensor.
The contact is normally open and closed when activated.
The contact is normally closed and open when activated.
2 Click ‘Apply’ to make above setting effective.
49
Setup - Record Setup
Record Management
1
2
3
4
1 Target Stream Select the channel you want to record video.
2 Click ‘Save’ to save the current settings.
3 Recording List Display the information about the recording settings.
4 Click ‘Modify’ to modify the selected item in the recording list.
50
Setup - Record Setup
Record Configuration
5
6
3
4
7
1
2
8
1 Enabled - The Recording function can be enable or disable.
2 Storage Device - Can not be selected and shows the saved SD Card.
3 File Type - Select the recording file type.
Currently only supports MP4 Type.
4 Storage - Select the storage type. SD Card(Disabled) selection is not allowed.
5 Continous - If continous mode is turned on, Start the continuous recording without any other setting.
6 Pre Duration - Define duration of recording before an event.
7 Post Duration Define duration of image transfer after an event.
8 Click ‘Save’ to save the current settings.
Click 'Cancel' to return to the previous setting.
51
Setup - Record Setup
Recording List
1
2
3
4
5
1 Storage - Select the Storage.
2 Filter Select the date / time, event, sort or storage format to filter the recorded video.
3 Click the 'Refresh' button to refresh the records list.
Click 'Filter' to view the filtered recorded video.
4 Recording List Display the information to the recording video.
5 Click 'Play' to view the selected item in list of recorded video.
Click 'Download' to download the selected item in list of recorded video.
- When you click Download, the following window appears.
- When downloading, please fill up the purpose within 30 characters. (The purpose you created is shown on the Log page with the download time)
When playbacking recorded MP4 file format with H.265 (HEVC) codec, video may not play due to the performance issue of VLC
plug-in.
52
Setup - Record Setup
Recording Video
1
2
3
1 Recording Video Viewer - Play the recorded video.
2 Recording Video Information Display the information about the recorded video.
3 Click 'Replay' to view the recorded video again.
Click 'Back' to return to the previous menu.
53
Setup - Record Setup
Storage Configuration
Display the SD card information mounted from device.
When you select the item in Storage list, You can set the functions related to the SD card.
54
Setup - Record Setup
Storage Configuration
1
2
3
4
5
6
1 Storage Size Total capacity of SD card and the remainder of it are displayed.
2 Auto Delete Select the period for Auto delete. The image data stored before period will be deleted automatically.
Delete all stored image older than selected time.
3 Overwrite If it is set ON and remained space of SD card reach to less than 8MB, new data will start to be overwritten on
the oldest data. However, if it is set OFF and remained space of SD card reach to less than 8MB, image recording will be stopped.
4 Unmount remove the SD card from the device.
5 Format Delete the all contents that stored in SD card.
6 Click ‘Apply’ to make above setting effective.
Click 'Cancel' to return to the previous setting.
55
Setup - Security Setup
IP Address Filter Configuration
3
4
1
2
5
6
1 IP Address Filter IP filter function can be enable or disable.
2 IP Filter Type - Select the recording IP filter type.
3 Click ‘Apply’ to make above setting effective.
4 Filter IP Address Display the filtered IP address.
5 IP Address - Define the IP address you want to apply the IP filter.
6 Click ‘Add’ to add the ip address to the list.
Click ‘Remove’ to remove the ip address selected in the list.
56
Setup - Security Setup
RTSP Authentication Configuration
1
2
1 RTSP Authentication RTSP Authentication can be enable or disable.
2 Click ‘Apply’ to make above setting effective.
57
Setup - Security Setup
IEEE 802.1X Configuration
6
7
8
3
4
1
2
5
9
The feature is needed when connecting the camera to the network protected by the IEEE 802.1X.
1 IEEE 802.1x - The IEEE 802.1x feature can be enable or disable.
2 Protocol
- MD5 : It provides one-way password-based network authentication of the client.
- PEAP : It is similar to TTLS in that it does not require a certificate on the client side.
- TTLS / MD5 : It does not require a certificate on the client side.
- TLS : It relies on client-side and server-side certificates to perform authentication.
3 EAPOL Version Select the EAPOL Version.
4 ID - Type the ID to identify the client in the IEEE 802.1X authentication server.
5 Password Type the Password to identify the client in the IEEE 802.1X authentication server.
6 Verify Verify Password.
7 CA Certificate Select the CA certificate required for TLS, TTLS, and PEAP authentication.
8 Certificate Select the client certificate required for TLS authentication
9 Click ‘Apply’ to make above setting effective.
58
Setup - Security Setup
HTTPS Configuration
1
2
3
HTTPS encrypts session data over SSL or TLS protocols instead of using plain text in socket communications.
1 Certificate Select an installed certificate.
If you can not select a certificate, please install the certificate from the Security->Certificates menu.
2 HTTPS connection Policy - Select one of “HTTP”, “HTTPS”, “HTTP and HTTPS” depending on the connected web, onvif, rtsp over http.
- WEB : “HTTP” “HTTPS” “HTTP and HTTPS”
- ONVIF, RTSP OVER HTTP : “HTTP” “HTTPS” “HTTP and HTTPS”
3 Click ‘Apply’ to make above setting effective.
When HTTPS mode is chosen, input https://<IP Address> to connect to the camera.
59
Setup - Security Setup
Certificates Configuration
1
2
5
7
8
3
4
6
9
10
1 Server/Client Certificates It show the installed certificates.
2 Create Self-Signed Certificate A self-signed SSL certificate is an identity certificate signed by its own creator.
But they are considered to be less trustworthy.
3 Properties - Shows information about the selected certificate.
4 Delete Delete the selected certificate.
5 Create Certificate signing request This is the encoded data that contains the necessary information for issuing the certificate.
They must be filled in when creating the CSR (Certificate Signing Request).
6 Install Certificate Install Certification
7 CA Certificate It show the installed CA certificates.
8 Install CA Certificate Install Certification, see the detail page.
9 Properties - Shows information about the selected certificate.
10 Delete - Delete the selected CA certificate.
60
Setup - Security Setup
Certificates Configuration
7
9
1
3
2
5
4
6
8
10
Detail for Install Certification.
1 Certificate From Signing Request Select to install signed certificate returned from the CA.
2 Certificate And Private Key Select to install Certificate And Private Key to install a certificate and private key.
3 Certificate Name Enter a unique name to identify certificate.
4 Select File Choose certification file.
5 OK - Request installing certificate.
6 Cancel Cancel install certificate and then back to certificates configuration.
Detail for Install CA Certification.
7 Certificate Name Enter a unique name to identify CA certificate.
8 Select File Choose CA certification file
9 OK - Request installing CA certificate.
10 Cancel Cancel install CA certificate and then back to certificates configuration.
61
Setup - Security Setup
Service Configuration
1
2
1 SSH - The SSH function can be enable or disable.
2 Click ‘Apply’ to make above setting effective.
62
Setup - System Setup
System Information
1
2
3
System Capability information.
1 Device Name - You can define the device name.
2 Location - Shows camera's location.
3 Click ‘Apply’ to make above setting effective.
63
Setup - System Setup
System Diagnostics
1
Shows basic hardware functions after inspection.
1 Shows Uptime, SD card, NAND, EEPROM, Audio chip, Important file system and NTP Status.
64
Setup - System Setup
Firmware Update
1
2
3
1 Version Information It shows the current Firmware Version in the system.
2 Web Update Select the Firmware file in your computer by clicking [Select file] button.
3 Start F / W Update Click this button to start update. Progress of uploading will be displayed using Progress Bar.
If you assign the wrong file name, an error message will be shown.
Warning:
1. Do not turn off the power of camera during the Firmware update. Otherwise, the system can be stuck to be unstable.
If updating is finished, the system will be rebooted automatically.
2. Please make sure to check the ‘Notice’ shown on screen.
If firmware update is completed, the camera will reboot automatically and ‘Setup window’ will be closed.
65
Setup - System Setup
Date & Time Settings
1
2
3
4
5
6
7
1 TimeZone Setup Choose TimeZone for camera. It will be activated after clicking ‘Apply’ button.
Prior to setting below ‘New Camera Date & Time’, set correct Timezone first.
2 Time Format Select the time format yy-mm-dd or mm/dd/yy.
3 Current Date & Time Shows the current date and time setting in the Camera.
4 Synchronize with my computer Set the date / time using those of PC currently connected.
5 Setup manually Set the date / time by typing manually.
6 Synchronize with time sever Time Zone (NTP) - Choose time server available to connect to current camera.
Date & Time will be updated automatically every hour when connected.
7 Click ‘Apply’ to make above setting effective.
66
Setup - System Setup
DST Settings
1
2
3
Daylight Saving Time (DST) is the practice of setting the clocks forward one hour from standard time during the summer months, and back again in the fall, in order to make better use of natural daylight.
1 General Setting - DST function can be enable or disable.
2 Date&Time Settings Set the Start time and end time that the DST apply.
3 Click ‘Apply’ to make above setting effective.
67
Setup - System Setup
Users Management
1
2 3 4
1
Users - List all the user accounts for authentication.
2
Add Register a new user.
ID Enter a new user ID except Admin since it exists.
Password Enter the user Password. (Check the Password)
Verify Enter the user Password again for verification.
User
Authority
Select Operator or Viewer.
Viewer : Only monitoring is allowed.
Operator : Most of the functions are allowed except ‘Setup’.
The ID is limited to 4~30 characters.
[Password Rules]
Weak : 8 characters or less, less than 2 combinations
Good : more than 8 characters, more than 3 combinations
strong : more than 12 characters, 4 combinations
If it is more than 'Good', you can change your password.
Combinations : uppercase letters, lowercase letters, numbers, special symbols.
Acceptable special characters are ~ ’ ! & ^ ( ) _ - | { } ; . ? /.
Click ‘Apply’ to make above setting effective.
Click 'Cancel' to return to the previous menu.
3
Modify - Modify the information of the user accounts registered. For admin account, only Password function can be modified.
4
Delete Delete the selected user account. Admin account cannot be deleted.
68
Setup - System Setup
System Log
1
2
3
1 Filter Select a date, time, sort or type of log to filter the log.
2 Click the 'Refresh' button to refresh the log list.
Click 'Filter' to view the filtered log.
Click 'Backup' to back up the filtered log.
3 System Log List - The filtered log is displayed.
69
Setup - System Setup
Language
1
2
1 Language Select the language you want from the list.
2 Click the 'Apply' to make above setting effective.
70
Setup - System Setup
Factory Reset
1
2
1 Reset to the factory defaults Return the setup to the factory default.
All Reset all Settings to the factory defaults.
Except Network Settings and User Settings Except Network, User related settings , reset all others to the factory default.
Only Camera Settings Reset only camera related settings to the factory defaults.
2 Click ‘Apply’ to make above setting effective.
71
Setup - System Setup
Restart
If you click the ‘RESTART’ menu, a message box will be shown to confirm. Click the ‘OK’ button to restart.
72
Setup - System Setup
System Open Source License
This menu will show you all the list of System Open Source License in the camera. Open Source Name / Version / License.
73
Appendix
A : Current TCP/IP Settings
i If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your
IP address. For information on how to do this, please read the FAQ.
1. Windows 7 Users
Start
Control Panel
Network and sharing center
Manage network connections
Properties
Select Internet Protocol
Ver.4 (TCP/IPv4)
Click Properties
Under the ‘General’ tab of the TCP/IP
Properties you will see your IP address information.
2. Windows 10 Users
Start
Settings
Network & Internet
Click on Change adapter options in Ethernet
Select the Ethernet, Right click and choose Properties
Select Internet Protocol
Ver.4 (TCP/IPv4)
Click Properties
Under the ‘General’ tab of the TCP/IP
Properties you will see your IP address information.
74
Appendix
B : Changing IP address and subnet mask
1. Windows 7 Users
Start
Control Panel
Network and sharing center
Manage network connections
Properties
Select Internet Protocol
Ver.4 (TCP/IPv4)
Click Properties
Select ‘Use the following IP address’
2. Windows 10 Users
Start
Settings
Network & Internet
Click on Change adapter options in Ethernet
Select the Ethernet, Right click and choose Properties
Select Internet Protocol
Ver.4 (TCP/IPv4)
Click Properties
Select ‘Use the following IP address’
75
Appendix
C : Port Forwarding
After assigning the IP Camera a web server port and video server port you must use Port
Forwarding. (for cases A, B)
Please consult your router’s user guide on how to correctly configure Port Forwarding.
For your convenience, we have provided two example configurations.
1. For D-Link DI-604 broadband routers:
1) Open a web browser and type http://192.168.0.1 into
your Address bar. (the default IP address to access the
router)
2) You will have to supply your User Name and Password to
log onto the router. Default from factory.
(User Name: admin Password: [leave blank])
3) Select the " 1 Advanced" tab and click " 2 Virtual
Server" menu.
1
2
1. For Linksys BEFSR41 Cable/DSL routers:
1) Open a web browser and type http://192.168.1.1 into you
Address bar. (the default IP address to access the router)
2) You will have to supply your User Name and Password to log onto the router. Default from factory
(User Name:[leave blank] Password: admin)
3) Select " 4 Applications & Gaming" from the menu bar.
4
4) Click " 3 Apply" button after inputting proper
values. The example is as below
3
Enabled / Disabled
Name
Private IP
Protocol Type
Private Port / Public Port
Schedule
Select "Enabled".
Input IVS name.
Input IVS address.
Select "TCP".
Input IVS Web Server Port.
Select "Always".
5) If 'Setting Saved' shows, click [Continue] button.
6) With the same method as above, add Video Server Port.
7) The Web Server Port, Video Server Port and 2 Audio
Ports shows in "Virtual Server List" as below.
4) Input port numbers in " 5 Port Range" as below and click
" 6 Save Setting" button. Both of Web Server Port and
Video Server Port should be added. The example is as
below.
5
6
Enabled / Disabled Input IP Camera name.
Start / End
Input IP Camera Web Server Port and
Video Server Port.
Start should be same as End.
Both of Web Server Port and Video
Server Port should be added.
Protocol
IP Address
Enabled
Select "TCP" in Protocol option.
Input IP Camera IP Address.
Check the square.
76
Appendix
C : Port Forwarding
3. For Netgear RP614 routers:
1) Input http://192.168.0.1 in address bar of web browser.
http://192.168.0.1 is the default IP address.
2) If it asks ID and password, input admin as ID and password
as password.
3) Click "Port Forwarding" in "Advanced".
4) Click " 1 Add Custom Service" button in Port Forwarding
page.
1
5) Input proper values in "Ports - Custom Services" page as
below.
2
Enable
Service Name
Check it.
Input IP Camera name.
Starting/ Ending
Port
Input IP Camera Web Server port.
Starting Port should be same as Ending
Port.
Server IP Address Input IP Camera IP Address.
6) Click " 2 Add" button.
7) With the same method as above, add Video Server Port.
8) Click "Apply" button to finish Port Forwarding.
77
Appendix
FAQ
1. My POWER light is not on?
Power is not being supplied to the unit. Please use the
power supply shipped with the unit and verify that a
power source is active from the attached power outlet
used to connect the adapter. You can test this by plugging
in any other electrical device and verify its operation. After
using the power supply shipped with the product, checking
the power source, and reinserting the power connector
into the IP Camera, please call our Support Center.
The power supply may be defective.
2. My ACTIVE light is not flashing?
Verify the power supply to the unit. Power off the unit
and back on again, wait 1 minute, if the ACTIVE light still
does not begin to flash, you will have to set the unit to its
factory default (THIS WILL DELETE ANY CONFIGURATION
AND SET THE UNIT TO THE FACTORY DEFAULTS).
Power on the unit and insert the end of a paper clip into
the small recessed opening on the back of the unit. Use
the clip to press the button located within that opening.
3. My LINK light is not flashing or solid?
Verify the cable connection. 99% of the time the cable’s
connection to the unit is causing this problem. Try using a
different network cable or crossover cable (for PC
connection only). Try reinserting the cable, if this still
doesn’t solve the problem call our Support Center.
4. I can access the video server on my LAN, but not from the
Internet.
Verify that your router (if applicable) has port forwarding
properly configured. If accessing from our DDNS service,
verify correct serial number. Firewall issues may prevent
user access.
5. How do I open an MS-DOS or Command Prompt?
Start > (All) Programs > Accessories > Command Prompt
6. How do I find out my IP address information if my settings
were automatically detected?
1) Open a Command Prompt
2) At the prompt type - “ipconfig / all” (without the quotes)
3) Near the end of the information supplied, should be
your current IP address, subnet mask, default gateway
and DNS servers
7. I can’t connect!!
In the case of a connection failure.
Modem Reboot > Modem Reboot Finished > Router
Reboot > Router Reboot Finished > IP Camera Reboot
> IP Camera Reboot Finish > Verify DDNS and IP Camera
connection, if applicable.
8. How do I “PING” an IP address?
1) Open an MS-DOS (or Command) prompt
2) At the prompt type - “ping xxx.xxx.xxx.xxx” (without the
quotes and replace the “x” s with an IP address)
3) Press Enter
9. I’m accessing my video server remotely over the Internet
and the video stream is choppy, is this normal?
Yes. The frames per second received remotely are
determined by your bandwidth capabilities both at
your site where the IP Camera is installed and your remote
location. The lower of the two sites will determine how
fast your video stream is received. It is recommended to
have at least a 256Kb/sec upstream connection from
the site where the IP Camera is installed. Lower speeds will
operate properly, but provide poor remote performance.
The Faster the Internet connection at both ends, the faster
the video stream.
10. How do I enable or check VLC on my browser
Internet Explorer
Open Internet Explorer > Tools on the menu bar > Internet
Options > Security Tab > Custom Level > Scroll down and
verify that you are prompted or have enabled plug-ins to
be downloaded and executed. > click OK > restart browser.
Chrome
Open Chrome > Chrome menu settings > Advanced
settings > Individual information - content settings > Run
automatically
11. How do I reset the unit to factory defaults?
Refer to the previous functions page and find the reset
button. Power ON the unit and use a paper clip to push
the reset button within that opening. You should then see
the ACTIVE light turn off and after a few seconds the
ACTIVE light will begin to flash, signifying a successful
reboot. If the ACTIVE light does not turn off after
depressing the reset button, please try holding the button
in for a few seconds and releasing. YOU WILL LOSE ALL
DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE IP
CAMERA WILL BE SET TO ITS FACTORY RESETS.
78

Public link updated
The public link to your chat has been updated.
Advertisement