Before operating a machine controlled by an electronic programmer, read this manual. Incorrect use can result in serious injuries or damage to the machine controls. Ignoring instructions can cause an incorrect machine function, which may result in injuries or machine and/or linen damages.

C001

• This English version is the original version of this manual.

Without this version, the instructions are incomplete. Before installation, operating and maintenance of the machine, read complete instructions thoroughly. Refer to the Installation/

Operation/Maintenance manual for further important instructions, as well. Follow these and keep the manuals accessible for later use.

• A machine must be installed by following the Installation/

Operation/Maintenance manual. Before the first machine start, it must be initialized and tested by a qualified technician.

• The electric service line must not be affected by other electrical loading. A nominal voltage, if loaded or not must work in the range ±10% with a maximum permanent frequency deviation of 1% or a short-time one at 2% of a given frequency.

NOTE: Connecting or starting the machine at an incorrect voltage can damage the programmer.

• The machine must not be exposed to high humidity or extreme high and low temperatures.

• Do not tamper with the controls.

IMPORTANT: Instructions in this manual do not cover all dangerous situations. It is up to the user to handle the machine carefully.

• The manufacturer has the right to change specifications in this manual without prior notice. All the stated information is only for informative purpose and must be considered as general. It is not possible to present all the specific data of the device.

NOTE:

Every circuit board has a serial number and the code of

the board (Refer to Figure 4 ).

On the EPROM memory chip on the circuit board is a label specifying the software number and version and/or the date of the software. (Refer to

Figure 4

These data, as well as the model and serial number of the machine, must be mentioned in all correspondence or inquiries addressed to the distributor or manufacturer.

NOTE:

The FULL CONTROL computer uses "machine type" codes to select the different programmable machine versions.

DO NOT COPY or TRANSMIT

6 Part No. D1707ENR4

Introduction

Model Identification

LC285FF

LC285LF

LC285MF

LC285NF

LC285SF

LC285TF

LC285WF

LC345EF

LC345LF

LC345MF

LC345NF

LC345SF

LC345TF

LC345WF

LC530EF

Information in this manual is applicable to these models:

LC190EF LU250SF

LC190FF

LC190LF

LU250WF

LU285EF

LC190MF

LC190NF

LC190TF

LC250EF

LU285FF

LU285MF

LU285SF

LU285WF

LC250FF

LC250LF

LC250MF

LC250NF

LC250SF

LC250TF

LC250WF

LC285EF

LU345EF

LU345MF

LU345SF

LU345WF

LU530EF

LU530MF

LU530SF

LU530WF

LU680EF

LU680MF

LU680SF

LU680WF

LUD26EF

LUD28EF

LUD28LF

LUD28SF

LUD28WF

LUS28EF

LX190EF

LX190FF

LX190LF

LX190MF

LX190NF

PCS28EF

PCS28LF

PCS28NF

PCS28TF

PGAE285F

PGAG285F

PGAL285F

PGAS285F

PGDE190F

PGDE250F

PGDE285F

PGDE345F

PGDE530F

PGDE680F

PGDG190F

PC530TF

PC530WF

PC680EF

PC680LF

PC680MF

PC680NF

PC680SF

PC680TF

PC680WF

PCD28EF

PCD28LF

PCD28NF

PCD28SF

PCD28TF

PCD28WF

DO NOT COPY or TRANSMIT

PU680WF

PUAE285F

PUAG285F

PUAL285F

PUAS285F

PUD28EF

PUD28SF

PUD28WF

PUDE190F

PUDE250F

PUDE285F

PUDE345F

PUDE530F

PUDE680F

PUDG190F

PU285FF

PU285MF

PU285SF

PU285WF

PU345EF

PU345MF

PU345SF

PU345WF

PU530EF

PU530MF

PU530SF

PU530WF

PU680EF

PU680MF

PU680SF

Table continues...

Part No. D1707ENR4

LX285TF

LX285WF

LX345EF

LX345LF

LX345MF

LX345NF

LX345SF

LX345TF

LX345WF

LX530EF

LX530LF

LX530MF

LX530NF

LX530SF

LX530TF

LX530WF

LX680EF

LX680LF

LX680MF

LX190TF

LX250EF

LX250FF

LX250LF

LX250MF

LX250NF

LX250SF

LX250TF

LX250WF

LX285EF

LX285FF

LX285LF

LX285MF

LX285NF

LX285SF

DO NOT COPY or TRANSMIT

Introduction

LH190EF

LH190FF

LH190LF

LH190MF

LH190NF

LH190TF

LH250EF

LH250FF

LCD28NF

LCD28SF

LCD28TF

LCD28WF

LCS28EF

LCS28LF

LCS28NF

LCS28TF

LH250LF

LH250MF

LH250NF

LC530LF

LC530MF

LC530NF

LC530SF

LC530TF

LC530WF

LC680EF

LC680LF

LC680MF

LC680NF

LC680SF

LC680TF

LC680WF

LCD28EF

LCD28LF

PH190MF

PH190NF

PH190TF

PH250EF

PH250FF

PH250LF

PH250MF

PH250NF

PGDS680F

PGSE285F

PGSG285F

PGSL285F

PGSS285F

PH190EF

PH190FF

PH190LF

PH250SF

PH250TF

PH250WF

PGDG250F

PGDG285F

PGDG345F

PGDG530F

PGDG680F

PGDL190F

PGDL250F

PGDL285F

PGDL345F

PGDL530F

PGDL680F

PGDS250F

PGDS285F

PGDS345F

PGDS530F

PX190LF

PX190MF

PX190NF

PX190TF

PX250EF

PX250FF

PX250LF

PX250MF

PUDS680F

PUS28EF

PUSE285F

PUSG285F

PUSL285F

PUSS285F

PX190EF

PX190FF

PX250NF

PX250SF

PX250TF

PUDG250F

PUDG285F

PUDG345F

PUDG530F

PUDG680F

PUDL190F

PUDL250F

PUDL285F

PUDL345F

PUDL530F

PUDL680F

PUDS250F

PUDS285F

PUDS345F

PUDS530F

Table continues...

Part No. D1707ENR4

LH345SF

LH345TF

LH345WF

LH530EF

LH530LF

LH530MF

LH530NF

LH530SF

LH530TF

LH530WF

LH680EF

LH680LF

LH680MF

LH680NF

LH680SF

LH680TF

LH680WF

LHD28EF

LHD28LF

LH250SF

LH250TF

LH250WF

LH285EF

LH285FF

LH285LF

LH285MF

LH285NF

LH285SF

LH285TF

LH285WF

LH345EF

LH345LF

LH345MF

LH345NF

DO NOT COPY or TRANSMIT

PC250LF

PC250MF

PC250NF

PC250SF

PC250TF

PC250WF

PC285EF

PC285FF

PC190FF

PC190LF

PC190MF

PC190NF

PC190TF

PC250EF

PC250FE

PC250FF

PC285LF

PC285MF

PC285NF

LX680NF

LX680SF

LX680TF

LX680WF

LXD28EF

LXD28LF

LXD28NF

LXD28SF

LXD28TF

LXD28WF

LXS28EF

LXS28LF

LXS28NF

LXS28TF

PC190EF

PH680LF

PH680MF

PH680NF

PH680SF

PH680TF

PH680WF

PHD28EF

PHD28LF

PH530EF

PH530LF

PH530MF

PH530NF

PH530SF

PH530TF

PH530WF

PH680EF

PHD28NF

PHD28SF

PHD28TF

PH285EF

PH285FF

PH285LF

PH285MF

PH285NF

PH285SF

PH285TF

PH285WF

PH345EF

PH345LF

PH345MF

PH345NF

PH345SF

PH345TF

PH345WF

Introduction

PX680EF

PX680LF

PX680MF

PX680NF

PX680SF

PX680TF

PX680WF

PXD28EF

PX345WF

PX530EF

PX530LF

PX530MF

PX530NF

PX530SF

PX530TF

PX530WF

PXD28LF

PXD28NF

PXD28SF

PX250WF

PX285EF

PX285FF

PX285LF

PX285MF

PX285NF

PX285SF

PX285TF

PX285WF

PX345EF

PX345LF

PX345MF

PX345NF

PX345SF

PX345TF

Table continues...

Part No. D1707ENR4

Introduction

LHD28NF

LHD28SF

LHD28TF

LHD28WF

LHS28EF

LHS28LF

LHS28NF

LHS28TF

LU190EF

LU190FF

LU190LF

LU190MF

LU250EF

LU250FF

LU250MF

PC285SF

PC285TF

PC285WF

PC345EF

PC345LF

PC345MF

PC345NF

PC345SF

PC345TF

PC345WF

PC530EF

PC530LF

PC530MF

PC530NF

PC530SF

Machine Type Selection

9 kg / 20 lb / 190 L

11 kg / 24 lb / 250 L

13 kg / 27 lb / 285 L

13/13 kg / 27/27 lb / 285/285 L

DO NOT COPY or TRANSMIT

T11VP

T13

LS300

T13E

T13VP

TAMS13

LSMS13

T13/13

LSD300

LS195

T9E

T9VP

T11

LS250

T11E

PHD28WF

PHS28EF

PHS28LF

PHS28NF

PHS28TF

PU190EF

PU190FF

PU190MF

PU250EF

PU250FF

PU250MF

PU250SF

PU250WF

PU285EF

T13

T13/13

T16

T24

T35

TAMS13

PXD28TF

PXD28WF

PXS28EF

PXS28LF

PXS28NF

PXS28TF

T11

Table continues...

Part No. D1707ENR4

16 kg / 35 lb / 345 L

24 kg / 53 lb / 530 L

35 kg / 77 lb / 680 L

T16

LS350

T16E

T16VP

T24

LS530

T35

LS680

Introduction

DO NOT COPY or TRANSMIT

11 Part No. D1707ENR4

Symbols Used

Buttons

Control Identification

Figure 1

Description of Buttons

REVERSE

- Switch On/Off Reverse function

START

- Starting up a program

- Continue an interrupted program

- Advancing the program step by step

STOP

- Interrupting a program

- Finishing a program

SERVICE

- shows the states and the total number of cycles of the machine

CFD1307R_SVG

CONFIRM THE SELECTION

CFD1309R_SVG

- Increasing a value

ARROW UP

- Selecting the next element of an item list

DRYING TIME

- Setting for drying time

PROGRAM SELECTION

- Selecting a program number

Table 1 continues...

DO NOT COPY or TRANSMIT

12 Part No. D1707ENR4

CFD1310R_SVG

or ARROW DOWN

- Decreasing a value

- Selecting the previous element of an item list

or ARROW LEFT

- Selecting the previous menu item

or ARROW RIGHT

- Selecting the next menu item

Description of Buttons

DRYING TEMPERATURE

- Setting for temperature

Table 1

COOLDOWN TIME

- Setting for cool down time

MOISTURE LEVEL

- Setting for residual moisture level

PROGRAMMING SWITCH

Programming switch is located inside the machine behind the control panel.

To access the programming switch:

• Machines 9 kg / 20 lb / 190 L – remove top cover.

• Machines 11 kg / 24 lb / 250 L, 13 kg / 27 lb / 285 L, 13 kg /

27 lb / 285 L - Top Pocked Tumbler, Stacked Tumbler, 16 kg /

35 lb / 345 L, 24 kg / 53 lb / 530 L, 35 kg / 77 lb / 680 L - the control panel must be unlocked

1. Programming switch

Figure 2

Run Mode: This is the Normal Dryer operation.

Control Identification

Program Mode: Only for changing the Dryer programs and machine settings.

DO NOT COPY or TRANSMIT

13 Part No. D1707ENR4

Control Identification

Main Menu

DO NOT COPY or TRANSMIT

14 Part No. D1707ENR4

Basic Description of Controls

General

The Control Offers

• 20 programmable programs (including 9 pre-programmed ones) kept in memory

• Each Program can be build in 5 steps

• Setting the machine options and configuration

• Multiple languages can be selected (one at a time)

In Operation the Following Data is Displayed:

• The selected program

• The active step

• The remaining program time

• The sequence function

• Indication of wait

• The temperature can be viewed

• Diagnostic messages

The Operation Menu:

• A program can be manually Shortened, Extended, Stopped.

• Service information

• Special function buttons to create simple dryer program

The Hardware and Software of the FULL CONTROL Dryer

Computer:

• Easy operation by a comprehensive keypad

• The hardware contains 1 electronic board

• The FULL CONTROL board with Alphanumerical LCD display

• The dryer control software is implemented in a Flash Memory that can be easily replaced

• The Dryer Programs are kept in EEPROM memory (non-volatile memory)

Specific Information

The PROGRAM Menu is designated for :

• The creation and implementation of a new dryer program step by step.

• Editing a dryer program step by step.

• Adding, inserting and deleting steps in the dryer program.

• Copying a dryer program.

• Inspecting the dryer program by the view function.

The CONFIGURATION Menu is designated for :

• The selection of the machine type.

• Loading the default factory settings for the CONFIGURA-

TION and INITIALIZATION menu.

• Erasing all the programmed dryer programs (reset Dryer program EEPROM memory).

• Loading the standard dryer programs.

• The selection if the temperature must be displayed in degrees

Celsius or degrees Fahrenheit.

• The selection of the Brightness of the display.

The INITIALIZATION Menu is designated for :

• The selection of the displayed Language.

• Programming the Service due value.

• The selection of the Buzzer time interval.

• The selection of the Advance function.

• Programming the Default Motor On and Off times for reversing motor action.

The SERVICE Menu is designated for :

• The inspection of the error messages log register and the list with statistics.

• The inspection of the functionality of the electric input signals.

• Resetting the cycle counter.

The DIAGNOSTIC Menu is designated for starting up a diagnostic program.

DO NOT COPY or TRANSMIT

15 Part No. D1707ENR4

Basic Description of Controls

20 Dryer Programs - 5 Steps

DO NOT COPY or TRANSMIT

16 Part No. D1707ENR4

The Creation of a Dryer Program

• A Dryer Program is built up step by step.

• Each step always consists of a Dry sequence and a Cooldown sequence.

• You will notice that each step has default settings. This feature is very helpful as most of the newly created programs will not require changes to be made to the suggested values.

Programming the Dryer sequence :

• First set the target temperature.

• Then set the Dry time or Humidity (only applies to machines fitted with a humidity sensor).

Programming the Cooldown sequence :

• After programming the Dry sequence, next program the Cooldown sequence.

• Set the parameter to stop the Cooldown sequence: Time or

Temperature

• As you will notice it’s also possible to skip a sequence between two other sequences by programming a time value = 0.)

The Anti-Wrinkle sequence :

• To avoid Wrinkling, its recommended that the linen is reversed each 2 to 10 minutes once the drying cycle has finished and the machine is not unloaded. A beep signal warns the operator that the cycle has been finished.

WARNING

A MORE DETAILED EXPLANATION FOR THE SPE-

CIFIC SEQUENCES CAN BE FOUND IN CHAPTER

PROGRAMMING.

C105

The Final Cooldown sequence :

• To avoid that the linen stays in the dryer with a too high temperature, for safety purposes, a Final Cooldown sequence is added at the end of the program.

• The Final Cooldown sequence takes 3 minutes if the temperature is above 122°F [50 °C], then the program is finished.

• The Final Cooldown sequence cannot be changed.

Programming the Functions

Limits:

• To ensure the correct functionality of the dryer you have to program values within certain limits.

• If you program a value that falls below the minimal or above the maximal programmable limit then the new value will not be accepted and the previous value stays valid.

Programming the Dry Temperature

• Limits:

Basic Description of Controls

• Dry Temperature : 33.8°F [1°C] - 158°F [70 °C]

• T24 & T35 GAS AND ELECTRICAL HEATING ONLY

• Dry Temperature : 33.8°F [1°C] - 179.6°F [82 °C]

Programming the Dry Time

• Limits:

• Dry Time : 0 – 120 Minutes

Programming the Cooldown Time

• Limits:

• Cooldown Time : 0 – 120 Minutes

Programming the Cooldown Temperature

• Limits:

• Cooldown Temperature : 33.8°F [1°C] - 158°F [70°C]

Programming the Motor On and Off times for Reversing

• The standard Reversing Motor On and Off times are 40 Seconds On and 5 Seconds Off.

• Limits:

• Reversing motor on Off times : 3 – 300 Seconds

Programming the anti-wrinkle sequence

• The drum is turning each 2 to 10 minutes for 5 seconds for a max programmable time of 3 hours.

• A buzzer is beeping when the drum turns.

• Limits:

• Action time Drum : 3 – 180 seconds

• Interval time Drum at rest: 1 – 15 minutes

• Anti-wrinkle time : 15 – 180 minutes

DO NOT COPY or TRANSMIT

17 Part No. D1707ENR4

Initializing the machine

Initializing the machine goes in four steps:

1. Install the machine mechanically. (refer to Installation Manual)

FULL CONTROL :

2. Select the machine specific settings in the Configuration

Menu.

3. Select the operator specific settings in the Initialization Menu.

4. Adjust standard Programs or create new Programs at the Program Menu.

WARNING

• The Main menu is now available.

• The Initialization Menu is the first Menu and is displayed immediately.

Main Menu Initialization

• Press the ENTER button to make your selection.

• Now you will see the first menu item.

• By pressing the ARROW RIGHT or LEFT button you can see the menu items one by one.

I:Language: English

• Select the preferred Language from the list by pressing the ARROW UP or DOWN button.

• English is the default setting.

• Press the ENTER button to confirm.

The initialization should be performed by qualified personnel only. An incorrect initialization may cause serious injuries and serious damage to the machine!

C026

WARNING

Before making changes in the configuration and initialization menu read this manual carefully.

C027

Changes you have made will influence the dryer program processes. We recommend before making changes to carefully write down what the previous settings were.

As the control dryer computer is used for a whole range of dryers, after the installation of a new control dryer computer, you need to program machine specific settings into the configuration

menu. Refer to Configuration Menu

At the installation of new software, after loading the factory set-

tings (refer to Configuration Menu

) you need to check the default settings one by one to find out if they correspond with the setup as you prefer.

The configuration and initialization of the dryer has been done at the factory. For the creation of new programs, no changes have to be made in the Initialization or Configuration menus.

Initialization Menu

HOW TO GET INTO THE INITIALIZATION MENU

The initialization menu can only be accessed when the machine is in standby (the power is switched on, but no program is started).

• SELECT PROCESS_ _ is displayed.

• Switch the programming switch Program Mode.

• English

• Dutch

• Czech

I:View Programs: Enable Menu ?

I:Enable Program X ?

Yes/No

• The 20 programs can be enabled or disabled in the

View Programs Enable

Menu.

• If you don‘t want to select the programs, press the

ARROW RIGHT button.

• If you want to select the programs, press the EN-

TER button.

• Press the YES or NO button to Enable / Disable programs.

• Yes is the default value.

• Yes : the Program is enabled. No : the Program is disabled.

• Press the ENTER button to confirm.

DO NOT COPY or TRANSMIT

18 Part No. D1707ENR4

I:Set Unwrinkle Time :

_ _ _ Min

• The Unwrinkle function avoids that the linen is wrinkled at the end of the dry cycle when the operator has no time to Unload the machine immediately.

• The unwrinkle time is the time that the machine will reverse the fabrics for a long intermedium time interval.

• The function is switched

OFF for a time setting = 0 minutes.

• Programmable in steps of 5 minutes.

• Limites : 0 – 180 minutes.

• 0 Minutes is the default value.

• Adjust the value with the

ARROW UP or ARROW

DOWN button and Press the ENTER button to confirm.

• The buzzer will function each time the mechanical action is restarted to warn the operator that the drying cycle has terminated.

I:Unwrinkle On Time :

_ _ Sec

I:Unwrinkle Off Time :

_ _ Min

Initializing the machine

• Set the Unwrinkle On and

Off Time.

• Limits :

• On Time : 3-99 seconds

• Off Time : 1-15 minutes

• Default value : - On Time :

• 5 seconds

• Off Time : 5 minutes

• Adjust the programmed time with the ARROW UP and DOWN buttons.

• Press the ENTER button to confirm.

I:Service Intervall :

3000

I:Buzzer Time : 5 Sec

• Insert the number of cycles at which a maintenance is required. Refer to Installation and maintenance manual.

• the default setting is :

• 3000

• Press the ENTER button to confirm.

• Insert the buzzer time. At the End of the Dryer cycle, when the message Unload is displayed, the buzzer will function for the programmed time.

• 5 Seconds is the default value.

• Press the ENTER button to confirm.

• The buzzer will function each time when operator’s attention is needed.

• The programmable Buzzer time interval is not applicable in the case of error messages.

DO NOT COPY or TRANSMIT

19 Part No. D1707ENR4

Initializing the machine

I:Allow Advance : Yes

I:Manual Override :

• With the Advance function you can Skip a Sequence or extend & decrease the time of a Sequence.

• Yes is the default value.

• Yes : the Advance function is enabled. No : the Advance function is disabled.

• Press the ENTER button to confirm.

• With the Manual Override function you can adjust drying time and temperature with the special function buttons when a dry sequence is running.

• Yes is the default value.

• Yes : the Manual Override function is enabled. No : the Manual Override function is disabled.

• Press the ENTER button to confirm.

set up with important parameters for various machine types. Basic machine adjusting is made in the factory.

WARNING

Only a qualified technician should change the configuration set up. An incorrect configuration can cause injuries and serious machine damage.

C028

HOW TO GET INTO THE CONFIGURATION MENU

The configuration menu can only be accessed when the machine is in standby (the power is switched on, but no program is started).

• SELECT Process_ _ is displayed.

• Switch the programming switch to Program Mode.

• The Main menu is now available.

• Press the ARROW RIGHT button to select the Configuration

Menu.

Main Menu Configuration

• Press the ENTER button to make your selection.

• For the Configuration Menu a Pass-Word is required.

Pass Word _ _ _ _

• Press the 4 function buttons one by one inside the rectangle and press the ENTER button.

I:Default Motor Turn

Time : _ _ Sec

I:Default Motor Rest

Time : _ _ Sec

• For programming the ON-

OFF reversing time, the default values are 40 Sec ON and 5 Sec OFF. Programmable between 3 and 99 sec.

• The purpose of these two items is to suggest the values to avoid that the operator has to insert over and over again the ON-OFF reversing times while programming new dryer programs.

• Press the ENTER button to confirm.

I:Initialization Menu Exit • You can leave the Initialization Menu by pressing the ENTER button.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

Configuration Menu

This electronic managing system has been specially constructed for a wide range of dryers. For that reason it must be individually

• Now you will see the first menu item.

• By pressing the ARROW RIGHT or LEFT button you can see the menu items one by one.

C:Machine type

T11

• By pressing the ARROW

UP or ARROW DOWN button you can select the machine type.

• Check the Machine data plate at the rear side of the dryer machine.

• Press ENTER button to confirm.

• As a result you will be asked if you are sure about your selection. C: Change

Machine type ? No

• Press YES and ENTER button to confirm once more.

DO NOT COPY or TRANSMIT

20 Part No. D1707ENR4

• T9

• T11

• T13

• T13/13

• TAMS13

• T16

• T24

• T35

WARNING

BE SURE THAT YOU WANT TO ERASE THE OLD

SETTINGS, AS THEY CAN’T BE RECAPTURED.

CHANGING THE MACHINE TYPE SHOULD ONLY OC-

CUR WHEN A NEW CONTROL DRYER COMPUTER IS

INSTALLED.

C111

WARNING

BE SURE THAT YOU HAVE SELECTED THE COR-

RECT MACHINE TYPE, OTHERWISE THE MACHINE

WILL NOT FUNCTION PROPERLY.

C112

WARNING

BY CHANGING THE MACHINE TYPE THE DRYER

PROGRAMS KEPT IN THE EEPROM MEMORY ARE

NOT CHANGED. AFTER CHANGING THE DRYER MA-

CHINE TYPE IT’S RECOMMENDED TO ERASE THE

PROGRAM MEMORY AND LOAD THE STANDARD

DRYER PROGRAMS AGAIN. THE DRYER PROGRAM

SETTINGS DIFFER FOR EACH MACHINE TYPE.

C113

WARNING

SELECTING RESET FACTORY IS RECOMMENDED IF

A NEW MACHINE TYPE HAS BEEN SELECTED. THIS

WILL ENSURE THAT ALL THE DEFAULT SETTINGS

OF THE NEW MACHINE TYPE ARE LOADED.

C114

DO NOT COPY or TRANSMIT

C:Reset Factory Settings?

C:Brightness Display :

Initializing the machine

• All the Initialization and

Configuration Menu settings will be cleared and the default Factory settings will be re-installed.

• This function should only be used at the initialization of a new FULL CON-

TROL Dryer Computer.

• Select Yes or No and confirm by pressing the EN-

TER button.

• By selecting YES , a new request for confirmation is displayed C: Delete old settings ? No

• Press the YES and ENTER button to confirm once more.

• You can control the brightness of the display or the angle at which you have an optimal contrast by programming a value between

1 and 20.

• The default value is 9.

• By pressing the ARROW

UP or DOWN button, you can adjust the value.

• Select the machine heating system from the list by pressing ARROW UP or

DOWN button.

• Gas heating

• Electrical heating

• Steam heating

• Heat pump (HP)

• The default value is Gas.

• Press the ENTER button to confirm.

C:Reversing System :

• Set the Reversing function

Yes if the machine type is executed with Reversing.

• No is the default value.

• Yes : the Reverse function is enabled. No : the Reverse function is disabled.

• Press the ENTER button to confirm.

Part No. D1707ENR4

Initializing the machine

C:Safety Temp 2 : 150

Gas Heated

Electrical

Heated

356 [180]

392 [200]

ONLY FOR GAS AND

ELECTRICAL HEATING

• At the heating system there is located a second Temperature sensor. It is used to protect heating system against overheating.

• If value is "0" then Second

Temperature Sensor is switched OFF.

T11

356 [180]

302 [150]

• The default value is (Temperature values in °F [°C]) :

Temperature values °F [°C]

T13

392 [200]

302 [150]

T13/13

338 [170]

302 [150]

T16

392 [200]

302 [150]

T24

392 [200]

T35

392 [200]

Table 2

• By pressing the ARROW UP or DOWN button, you can adjust the value.

C:Humidity Control

System : No

C:Temperature: Celcius

• Set the Humidity Control function Yes if the machine type is executed with Humidity Control.

• No is the default value.

• Yes : the Humidity Control function is enabled. No : the Humidity Control function is disabled.

• Press the ENTER button to confirm.

• Press the ARROW UP or

DOWN button to select

Celsius or Fahrenheit, depending if you prefer that the temperature is displayed in degrees Celsius or degrees Fahrenheit.

• Confirm by pressing the

ENTER button.

DO NOT COPY or TRANSMIT

22 Part No. D1707ENR4

C:Lint Warning Limit :

• The Lint Filter must be cleaned every day. Depending the kind of Fabrics there will be more or less lint.

• As memory support, a warning will be displayed at the end of the drying cycle if the machine exceeds the programmed number of cycles.

• The default value is 15.

• A value between 5 and 20 can be programmed.

• Depending the amount of lint, you can reduce or increase the number of cycles for which the Alarm must occur.

• Confirm by pressing the

ENTER button.

NOTE:

By opening the lint door the „Lint Door Cycle

Counter“ will be reset.

By opening the dryer door the Warning will be erased from the display but will not reset the Lint

Door Cycle Counter.

If the „Lint Door Cycle

Counter“ has not been reset for 40 cycles, an

Error message will be displayed and the machine can’t be started anymore until the error message is reset by the programming switch.

C:Erase All Programs?

Initializing the machine

• You can erase all the dryer programs at once.

• This function should only be used at the installation of a new FULL CON-

TROL Dryer Computer and if you want to ensure that no old programs stay in the memory of the computer.

• For all 20 programs default values will be loaded.

• Select Yes or No and you have to confirm by pressing the ENTER button.

• By selecting YES , a new request for confirmation is displayed. C: Delete all

Programs ? No

• Press YES and ENTER button to confirm once more.

DO NOT COPY or TRANSMIT

23 Part No. D1707ENR4

Initializing the machine

C:Load Standard Programs?

C:Language: English

• If you want to make use of the 9 Standard Dryer programs, these standard programs must be loaded into the Dryer Program Memory of the FULL CON-

TROL Computer.

• Press the ENTER button if you want to Load the

Standard programs.

• Then a Confirmation is asked before the First 9 dryer program’s will be loaded.

• By pressing Yes and EN-

TER button, 9 Standard program’s will be loaded at the Program numbers 1 to

• The Standard dryer program‘s can be found in this manual in chapter 7.

• Then you can Select the language of the Dryer Program name.

• By the Dry Program Name the operator knows which kind of dry process the program corresponds with.

• You can select the Language from a list by pressing the ARROW UP „+“ or

DOWN „-“ buttons and you have to confirm with the ENTER button.

C: Communication Address : XXX

• Each dryer machine in the

RS485 laundry machine network must have a unique Communication

Address.

• 255 is the default value.

• Enter a unique number between 1 and 255.

• Confirm by pressing the

ENTER button.

Remark

• If 2 or more machines have the same Communication

Address then the network will not function properly.

DO NOT COPY or TRANSMIT

24 Part No. D1707ENR4

C: Configuration Menu

Exit

• You can leave the Configuration Menu by pressing the ENTER button.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

Humidity Control

Residual Humidity Linen

Initializing the machine

1. Heating up

2. Linen is wet

3. Linen is dry

4. Part 1: RH > 30%

5. Part 2: RH < 30%

6. H -- shown on display

7. H XX shown on display

8. Dry cycle time

DO NOT COPY or TRANSMIT

Figure 3

25 Part No. D1707ENR4

Initializing the machine

At the drying process with humidity control, the air humidity is measured by an absolute air humidity sensor. The graph shows the absolute air humidity in function of time. When a drying cycle is started, the air humidity will go up quickly as the heating system starts up, then the air humidity will decrease bit by bit.

The dryer computer humidity sensor measures this value and calculates the corresponding residual humidity of the linen. The residual humidity is the remaining amount of water in wet linen compared with it's dry equivalent. When the linen is taken out a washing machine:

• A high extraction speed results in about 50 % residual humidity

• A low extraction speed results in about 70 % residual humidity

At the drying cycle (humidity control) the display shows :

• H - - : The residual humidity is above 30 % (the linen is wet)

• H XX : The residual humidity value is below 30% (the linen gets dry)

Above 30% residual humdity, the linen is so wet that there is no accurate measurement. For this reason there is not shown a value on the display, just two dashes. It can take 10 to 40 minutes, depending the amount of load and how wet the linen is, before the

Residual Humidity Value is shown on the display.

The default programmed value for residual humidity of linen is

5%.

IMPORTANT: While the dryer is running, do not open and close the door, it disturbs the humidity control measurement.

WARNING

CERTAIN FABRICS CAN GET DAMAGED WHEN

DRYED UNTIL A RESIDUAL HUMIDITY OF 0%.

(BONE DRY). CERTAIN FABRICS GET ELECTRO-

STATIC CHARGED FOR A RESIDUAL HUMIDITY BE-

LOW 5% (WHICH SHOULD BE AVOIDED).

C132

WARNING

THE HUMIDITY CONTROL SYSTEM IS NOT MADE TO

RUN WITHOUT LOAD OR WITH A VERY SMALL

LOAD. THE SYSTEM CAN ONLY FUNCTION IN A

NORMAL WAY WHEN THERE IS SUFFICIANT EVAP-

ORATION TO BE MEASURED BY THE AIR HUMIDITY

SENSOR.

C133

DO NOT COPY or TRANSMIT

26 Part No. D1707ENR4

How to Create and Adjust a Dryer Program

Initializing the machine

DO NOT COPY or TRANSMIT

27 Part No. D1707ENR4

Programming

General

Specific functions have been implemented in the FULL CON-

TROL dryer computer to allow a detailed programming.

Functions for the complete program.

• Program Number : Selecting the dryer Program

• Program Name : Creating the Program Name

• View : Inspecting the Program settings without making changes

• Edit : Adjusting a Program

• Copy : Making a Copy of an existing Program

• Exit : Leave the Program Menu

Functions for the program steps.

• Step Number : Selecting the Program Step

• Edit : Adjusting the Program Step

• Add : Adding a Program Step at the end of the program

• Insert : Inserting a Program step in between other Program

Steps

• View : Inspecting the Step settings without making changes

• Delete : Deleting a Step

• Exit : Leave the Program Step Menu

Follow the flowchart step by step.

Step 1: Program Menu

HOW TO GET INTO THE PROGRAM MENU

The initialization menu can only be accessed when the machine is in standby (the machine is powered up but no program is started).

• SELECT Process_ _ is displayed.

• Switch the programming switch to Program Mode.

• The Main menu is now available.

• Press the ARROW RIGHT button to select the Program

Menu.

Main Menu PROGRAM

• Press the ENTER button to confirm your selection.

• Goto Step 2: Program Functions

Step 2: Program Functions

SELECT THE PROGRAM NUMBER

P:Give Program Number : _ _

• Select the desired program number by pressing the

ARROW UP or DOWN button.

• Program 1 to 20 can be selected.

• Press the ENTER button as a confirmation.

VIEW A PROGRAM

P: Program N°XX

View

EDIT A PROGRAM

P: Program N°XX Edit

• In Program View you can look to the Program Settings, without making changes.

• Press the ARROW RIGHT button if you don‘t want to see the program Over-

View.

• Press the ENTER button if you want to see the program Over-View.

NOTE: In the program

Over-View Menu, at the end of a Dryer Program

Step, Press the ENTER button to see the next step. Refer to also

Step 3:

Program Step Functions »

• Editing a program is changing the program by selecting a new element from a list or by changing values in an existing program. You can also add, or delete steps in an existing program.

• Press the ARROW RIGHT button if you don‘t want to

Edit the program.

• Press the ENTER button if you want to Edit the program. Goto

Step 3: Program Step Functions

DO NOT COPY or TRANSMIT

28 Part No. D1707ENR4

Programming

COPYING A PROGRAM

P: Program N°XX

Copy

P: Copy from Program

N° _ _ _

EXIT THE PROGRAM MENU

P: Program Menu Exit

• If you want to adjust a new program, sometimes it’s easier to make a copy of an existing program and to make some small changes to your new copy.

• Press ARROW RIGHT button if you don‘t want to

Copy a program.

• Press the ENTER button if you want to make a copy from another program.

• A confirmation is asked to delete the old program. P:

Delete Old Program? No

• Press the ENTER button if you don‘t agree to copy the

old program. Goto Step 1:

Program Menu »

• Press YES and ENTER button to confirm if you want to implement a new program.

• Insert the desired program number from which you want to copy the program.

• Press the ENTER button as a confirmation. Goto

Step

1: Program Menu

Step 3: Program Step Functions

EDIT A STEP

P:Edit Step : _ _

• If you edit a step, you will change values or list elements from an existing step.

• Press the ARROW RIGHT button if you don‘t want to

Edit a step.

• Select the Step number. If the number is not accepted, this means that the step is not available.

• Press the ENTER button to confirm your selection.

Goto Step 4: Programming the Drying Part

ADDING A STEP AT THE END OF THE PROGRAM

P:Add Step

• Default programs have only 1 step. For more complicated programs, you can add 4 extra steps. New steps are added at the end of the program.

• Press the ARROW RIGHT button if you don‘t want to

Add a new step.

• Press the ENTER button if you want to add a new step. Goto

Step 4: Programming the Drying

Part »

• Press the ENTER button if you want to leave the PRO-

GRAM Menu.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

INSERTING A STEP BETWEEN EXISTING STEPS

P:Insert Step : _ _

• Default programs have only 1 step. For more complicated programs, you can add 4 extra steps. Steps are inserted in between other steps. The steps with the same or higher number will be increased with 1.

• Press the ARROW RIGHT button if you don‘t want to

Insert a new step.

• Press the ENTER button if you want to Insert a new step. Goto

Step 4: Programming the Drying

Part »

DO NOT COPY or TRANSMIT

29 Part No. D1707ENR4

Programming

VIEW A STEP

P:View Step : _ _

DELETE A STEP

P:Delete Step : _ _

• Before making changes in a dryer program, it‘s recommended to have a look at the actual settings by the view function.

• Press the ARROW RIGHT button if you don‘t want to

View a step.

• Select the Step number. If the number is not accepted, this means that the step is not available.

• Press the ENTER button to confirm your selection.

Goto Step 4: Programming the Drying Part

NOTE: Step 1 can not be deleted.

• If you delete a step, an existing step in the program will disappear.

• Press the ARROW RIGHT button if you don‘t want to

DELETE a step.

• Select the Step number.

• Press the ENTER button to confirm your selection. If the number is not accepted, this means that the step is not available.

• A confirmation is asked to delete the old step. P: Delete Old Step? No

• Press the ENTER button if you do NOT want to delete the old step.

• Press YES and ENTER button to confirm if you want to delete a step. Goto

Step 3: Program Step

Functions

P:Step Menu Exit

• Press the ENTER button if you want to leave the PRO-

GRAM STEP Menu.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

Step 4: Programming the Drying Part

This paragraph gives a detailed explanation about programming the Dryer Sequences.

• Each program step contains a drying part and a cooldown part.

• First the dryer part must be selected, item by item can be programmed.

• Next the cooldown part must be selected, item by item can be programmed. Refer to

Cool-Down Function ».

• Without making changes you can watch item by item, by pressing the ARROW RIGHT or LEFT button.

• If you want to make changes :

• Adjust a value by pressing the ARROW UP „+“ or

DOWN „-“ button

• Enable or disable a Setting by pressing the ARROW UP

„Yes“ or DOWN „No“ button.

• Select a list element by pressing the ARROW UP

„Next“ or DOWN „Previous“ button.

• Each time you add a new step, default values have been preprogrammed. So with less effort, complete programs can be programmed. Refer to also chapter Basic description of controls for a general explanation concerning the creation of dryer programs.

• You can recognise a list element by the „ARROW UP &

DOWN“ symbol at the right side on the display.

• Press the ARROW RIGHT button to go to the last Menu

Item : EXIT.

THE DRY SEQUENCE

EXIT STEP MENU

DO NOT COPY or TRANSMIT

30 Part No. D1707ENR4

P:Pr XX Step XX

Temp : 45 °C

P:Pr XX Step XX

DryType : Time

°C : degrees Celsius

°F : degrees Fahrenheit

• The temperature can be programmed between

33.8°F [1°C] and 158°F

[70°C].

• T24 & T35 GAS AND

ELECTRICAL HEATING

ONLY

• Dry Temperature :

33.8°F [1°C] - 179.6°F

[82°C]

• 113°F [45°C] is the suggested default value.

• Adjust the desired temperature. Press the ENTER button for confirmation.

• 2 types of dry sequence can be selected.

1. Time controlled sequence: The dry sequence will stop after the specified period of time.

2. Sequence controlled by time and residual moisture (only applies to machines fitted with a humidity sensor): The dry sequence will stop after the specified period of time or after the specified laundry residual moisture has been reached.

• By the ARROW UP and

DOWN button you can select the required setting.

Press the ENTER button for confirmation.

P:Pr XX Step XX

DryTime : _ _

P:Pr XX Step XX

DryHumidity : _ _ %

P:Pr XX Step XX

CoolType : Time

Programming

• The Dry Time is the programmed time that the linen is dried by forced heating.

• The default value is 30 minutes.

• The value is programmable between 0 and 120 minutes.

• Adjust the desired Drytime. Press the ENTER button for confirmation.

• The DryHumidity value is the programmed value for which the dry process is stopped when the target residual moisture in the linen has been reached. (Dried by forced heating.)

• The default value is 5 %.

• The value is programmable between 0 and 30 %.

(50-70% is the residual moisture level after extraction in washing machine.)

• Adjust the desired Humidity level. Press the ENTER button for confirmation.

• 2 types of CoolDown sequence can be selected.

The Cooldown sequence will be stopped at :

• a preset Cooldown time.

• a preset Temperature value

• By the ARROW UP and

DOWN button you can select the required setting.

Press the ENTER button for confirmation.

DO NOT COPY or TRANSMIT

31 Part No. D1707ENR4

Programming

P:Pr XX Step XX

CoolTime : _ _ Min

P:Pr XX Step XX

CoolTemp : _ _ °C

P:Pr XX Step XX

CoolRatio : _ _

• The Cooldown Time is the programmed time for which the dryer is cooling the fabrics. (Heating is switched Off).

• The default value is 5 minutes.

• The value is programmable between 0 and 120 minutes.

• Adjust the desired Cooldown Time. Press the EN-

TER button for confirmation.

• The Cooldown Temperature is the programmed temperature for which the dryer is cooling the fabrics.

(Heating is switched Off)

• The default value is 104°F

[40°C].

• The value is programmable between 32°F [0°C] and

158°F [70°C].

• Adjust the desired Cooldown Temperature. Press the ENTER button for confirmation.

• For special applications, a controlled cooldown sequence is required.

• The temperature will decrease in small steps in relation to the time. The ratio for the cooldown sequence is the temperature in function of time.

• The default value is 32°F

[0°C]/Min.

• The value is programmable between 32°F [0°C] and

41°F [5°C]/Min.

• Adjust the desired Cooldown Ratio. Press the EN-

TER button FOR CON-

FIRMATION.

P:Pr XX Step XX

Reversing : Yes

P:Pr XX Step XX

TurnTime : _ _ sec

P:Pr XX Step XX

RestTime : _ _ sec

Only for machines executed with reversing.

• Reversing can be switched

Off and On.

• The default value is Yes.

• By the ARROW UP and

DOWN button you can select the required setting.

Press the ENTER button for confirmation

Only for machines executed with reversing.

Settings are applicable for the DRY and COOLDOWN part of the Step.

• A reversing Motor On/Off time can be programmed.

• Depending the kind of fabrics, a short or long reverse time is applicable.

• Default values: 40 sec On and 5 sec Off time.

• Programming limits:

• On: 3 - 120 sec

• Off: 1 - 15 sec

• Adjust the desired Motor

On and Off times. Press the

ENTER button for confirmation.

DO NOT COPY or TRANSMIT

32 Part No. D1707ENR4

P: Program Step XX

Exit

• You can always return to a previous menu item by pressing the ARROW

LEFT button.

• By pressing the ENTER button you will leave the current Step. Goto

Step 3:

Program Step Functions

Programming

DO NOT COPY or TRANSMIT

33 Part No. D1707ENR4

Operation menu

Start Up

WARNING

BEFORE STARTING UP THE FIRST TIME, BE SURE

THAT THE MACHINE IS WELL INSTALLED. SEE IN-

STALLATION AND MAINTENANCE MANUAL. MAKE

SURE THAT THE CONFIGURATION AND INITIALIZA-

TION MENU HAVE THE RIGHT SETTINGS. SEE

CHAPTER INITIALIZING THE MACHINE.

C129

WARNING

DRY CYCLES CAN ONLY BE STARTED WHEN THE

PROGRAMMING SWITCH IS IN RUN MODE.

C130

• For each Dryer program Step :

• first you will see the Dryer Sequence

• then you will see the Cooldown Sequence

• A row of bars, shows you if the Sequence has just been started or if ¼, ½ or ¾ of the Sequence time is over.

PrXX StYY ZZ.Z Min

Dry

PrXX : The selected program number.

StYY : The selected program Step.

ZZ.Zmin or ZZ.Z H : The remaining program time in 1/10 of Minutes or 1/10 of Hours.

: A row of bars appears as a function of the remaining sequence time.

Dry : The executed Sequence. (example, Dry)

Advancing a Dryer Program

Switch On the Power

The display lights up when the power is turned on.

• If the program is ready to be started, Select Process _ _ is displayed.

Load the Dryer

1. Press the ARROW UP button to increase the dry-cooldown sequence time.

2. Press the ARROW DOWN button to decrease the dry-cooldown sequence time.

3. Press the START button to skip the current step. >> >> is displayed instead of the remaining time at the moment that the step is skipped.

1. Open the door

2. Load laundry into the drum

3. When the drum is loaded, close the door

Start a Dryer Program

WARNING

Even if the advance function has been switched off in the initialization menu, the advance function will work if the programming switch is turned into program mode.

C066

1. Create a simple program by the special function buttons on the keypad.

2. Press the ARROW UP and DOWN buttons to adjust the corresponding values.

3. Or Select the program number by the PROGRAM SELECT button.

4. Up to 20 programs can be selected. The first 9 are the standard Drying programs you can find in this manual.

5. Press the „START“ button.

The Active Program

• The cycle time will decrease minute by minute and gives you an indication how long it will take before the cycle is finished.

Drying Time

Once the program has been started, the remaining dry time is displayed in minutes.

Program End

1. The "0" on the display will be erased and the machine is ready to start a new program.

2. Once the program cycle is finished, UNLOAD is displayed.

3. Open the door and unload the machine.

• The Message UNLOAD will be erased and the machine is ready to start a new program.

• SELECT PROCESS _ _ is displayed.

DO NOT COPY or TRANSMIT

34 Part No. D1707ENR4

Operation menu

Cool-Down Function

WARNING

• For Safety purposes the machine will always execute a cooldown sequence at the end of the drying cycle. (Programmed dry temperature > 122°F [50°C]). Even if the cooldown time has been put on 0 minutes in the program menu.

Stop

Go to the chapter Troubleshooting to find out more about error handling.

C070

How to Handle Power Interruptions

• By pressing the STOP button the program is interrupted.

• First the machine will go over to a safe state.

• Then the message CONTINUE ? is displayed.

» STOP : the program is stopped.

» START : the program goes on with the rest of the cycle.

Wait State

Normal machine operation can be interrupted. You have to wait until the FULL CONTROL Dryer Computer allows you to go on.

You can recognize the wait state by a display that shows WAIT and a decreasing counter.

This will occur when the power has been switched off and on at a running dry cycle.

A delay time is respected before the machine can be restarted.

How to Handle Failure Messages

NOTE: For more information about error messages refer to

How to Handle Fault Messages

• When a failure has been detected by the FULL CONTROL

Dryer Computer, a failure message is generated, to inform the operator about the problem.

PrAA StBB Unload !

EXXX:YYYYYYYYYYYY

AA : The Program number

BB : The Step number

Unload ! : If it is allowed to open the door, the message Unload is displayed

E XXX : The error number

YYYYYYYY : The name of the error message

• At the upper left corner, the program number and step number of the interrupted program are displayed.

• The message UNLOAD ! will inform you if it‘s allowed to open the door.

Safety conditions

• If the actual temperature is too high the message „TOO

HOT“ will be displayed together with the actual temperature.

When a power interruption occurs while the machine is in standby mode, and no program cycle was started, the machine will stay in standby mode.

When a power interruption occurs while the dry or cooldown sequence is busy, after the power interruption, the message Continue ? will be displayed.

» STOP : the program is stopped.

» START : the program goes on with the last active step until the end of the program.

Service-State Button

• The Service button is dedicated to supply the operator with more information about the dryer machine functions.

» Press the SERVICE-STATE button if you want to inspect the actual temperature and humidity level.

• At the Service - State menu, you can inspect :

• the dryer temperature and humidity level

• the number of cycles that have been accumulated (service due)

• the actual dryer machine states at the running dry cycle

• By switching the programming switch to Program Mode, the

Service-State menu will not disappear after 1 minute.

• By pressing the ARROW RIGHT button you will see all the menu items.

• You can leave the Service - State menu by pressing the SERV-

ICE-STATE button again.

DO NOT COPY or TRANSMIT

35 Part No. D1707ENR4

Pre-programmed programs

General

The FULL CONTROL Dryer Computer contains 9 pre-programmed Standard Dryer Programs.

Drying Programs

WARNING

THE PRE-PROGRAMMED PROCESSES ARE GIVEN

AS AN EXAMPLE ONLY. FOR THE CREATION OF

YOUR OWN PROGRAMS, CHECK THE PROPERTIES

OF THE FABRICS AND THE RESIDUAL MOISTURE

AFTER THE DRYING PROCESS.

C134

Step 1

Sequence

Drying

Cooldown

Program 1: COLD 20 MIN

Temperature.

Time (minutes)

Table 3

Reversation (seconds)

A = 40

R = 5

Step 1

Sequence

Drying

Cooldown

Sequence

Drying

Cooldown

Sequence

Program 2: LOW 86°F [30°C] 20 MIN

Temperature.

86°F [30°C]

Time (minutes)

Table 4

Reversation (seconds)

A = 40

R = 5

Program 3: LOW 95°F [35°C] 30 MIN

Temperature.

95°F [35°C]

Time (minutes)

Table 5

Reversation (seconds)

A = 40

R = 5

Program 4: MEDIUM 104°F [40°C] 40 MIN

Temperature.

Time (minutes)

Table 6 continues...

Reversation (seconds)

DO NOT COPY or TRANSMIT

36 Part No. D1707ENR4

Step 1

Drying

Cooldown

Sequence

Drying

Cooldown

Sequence

Drying

Cooldown

Sequence

Drying

Cooldown

Sequence

Drying

Cooldown

Sequence

DO NOT COPY or TRANSMIT

Pre-programmed programs

Program 4: MEDIUM 104°F [40°C] 40 MIN

104°F [40°C] 40

Table 6

A = 40

R = 5

Program 5: MEDIUM 113°F [45°C] 30 MIN

Temperature.

113°F [45°C]

Time (minutes)

Reversation (seconds)

A = 40

R = 5

Program 6: MEDIUM 122°F [50°C] 40 MIN

Temperature.

122°F [50°C]

Time (minutes)

Table 7

Reversation (seconds)

A = 40

R = 5

Program 7: HOT 140°F [60°C] 30 MIN

Temperature.

140°F [60°C]

Time (minutes)

Table 8

Reversation (seconds)

A = 40

R = 5

Program 8: HOT 149°F [65°C] 40 MIN

Temperature.

149°F [65°C]

Time (minutes)

Table 9

Reversation (seconds)

A = 40

R = 5

Program 9: HOT 158°F [70°C] 30 MIN

Temperature.

Time (minutes)

Table 10 continues...

Reversation (seconds)

37 Part No. D1707ENR4

Pre-programmed programs

Step 1 Drying

Cooldown

Program 9: HOT 158°F [70°C] 30 MIN

158°F [70°C] 30

Table 10

A = 40

R = 5

Step 1

Sequence

Drying

Cooldown

Program 10: HOT X °F [°C] MIN

Temperature.

X°F [°C]

Time (minutes)

Table 11

Reversation (seconds)

A = 40

R = 5

T24 & T35 electrical heating only: X = 176°F [80°C ]

T24 & T35 gas heating only X = 167F° [75°C]

Step 1

Sequence

Drying

Cooldown

T24 & T35 steam heating only X = 158°F [70°C]

T9, 11, 13, 13/13, 16: X = 158°F [70°C]

Program 11: HOT X °F [°C] 30 MIN

Temperature.

X °F [°C]

Time (minutes)

Table 12

Reversation (seconds)

A = 40

R = 5

T24 & T35 electrical and gas heating only: X = 179.6°F [82°C]

T24 & T35 steam heating only: X = 158°F [70°C]

T9, 11, 13, 13/13, 16: X = 158°F [70°C]

REVERSATION

• A = 40 seconds = 40 Seconds Action (Drum Turns)

• R = 5 seconds = 5 Seconds Rest (Drum is at Standstill)

Program 12: Wool

Step 1

Step 2

Step 3

Sequence

Drying

Cool Down

Drying

Cool Down

Drying

Cool Down

Temperature

107.6°F [42°C]

105.8°F [41°C]

104°F [40°C]

Table 13

Humidity (%) Time (minutes)

Reversation

(seconds)

DO NOT COPY or TRANSMIT

38 Part No. D1707ENR4

Step 1

Step 2

Step 3

Step 1

Step 2

Step 3

Step 1

Step 2

Step 3

Sequence

Drying

Cool Down

Drying

Cool Down

Drying

Cool Down

Pre-programmed programs

Program 13: Silk

Temperature

104°F [40°C]

102.2°F [39°C]

96.8°F [36°C]

Table 14

Humidity (%)

Time (minutes)

Reversation

(seconds)

Sequence

Drying

Cool Down

Drying

Cool Down

Drying

Cool Down

Program 14: All In One

Temperature

109.4°F [43°C]

107.6°F [42°C]

105.8°F [41°C]

Table 15

Humidity (%) Time (minutes)

Reversation

(seconds)

Sequence

Drying

Cool Down

Drying

Cool Down

Drying

Cool Down

Program 15: Delicate Items

Temperature

100.4°F [38°C]

96.8°F [36°C]

105.8°F [41°C]

Table 16

Humidity (%) Time (minutes)

Reversation

(seconds)

DO NOT COPY or TRANSMIT

39 Part No. D1707ENR4

Pre-programmed programs

Step 1

Sequence

Drying

Cool Down

Program 16: No Heating

Temperature

95°F [35°C]

Table 17

Humidity (%) Time (minutes)

Reversation

(seconds)

DO NOT COPY or TRANSMIT

40 Part No. D1707ENR4

Troubleshooting

Display Messages

• Various messages may appear on the display at the start, during or at the end of a drying cycle.

• In some specific cases, an acoustic signal will alert the operator.

• When an error occurs the machine will automatically go over to a safe state.

Fault Messages

• If a failure occurs, the computer will display a diagnostic error message.

• The program number and step at which the interruption has occurred are displayed.

• The fault message itself contains a number and a corresponding text label by which it’s easy to find the related information in the manual.

• If Unload ! is displayed, it’s allowed to open the door.

PrXX StYY Unload !

EZZZ: Fault message

XX : the program number

YY : the program step number

Unload ! : open the door if Unload ! is displayed

EZZZ : the number of the occurred error

Fault message : the text label of the error message

How to Handle Fault Messages

WARNING

Check in the manual to see what problem the error message corresponds with. Ask the assistance of an experienced technician to solve the problem. All the safety precautions must be followed before each intervention.

C075

• You can overrule and erase fault messages by:

• Pressing the STOP or ENTER button (programming switch in program mode)

• Switching the power off/on

• Opening the door (Ignition Error, Air Flow Switch)

• Each time at the end of the cycle, the FULL CONTROL Dryer computer will fulfil a cooldown sequence

• (Actual temperature >122°F [50°C]).

• If at the end of the cycle the safety conditions are not fulfilled

(Temperature > 122°F [50°C]), the message TOO HOT will be displayed. (TOO HOT MESSAGE IS ERASED BY

OPENING THE DOOR, A NEW SEQUENCE CAN BE

STARTED)

TOO HOT

XX °C

• If the problem disappears, (the temperature has dropped below 122°F [50°C]) the Error message TOO HOT will disappear automatically.

WARNING

IT’S UP TO THE OPERATOR TO TAKE THE NECES-

SARY PRECAUTIONS FOR HIGH TEMPERATURES

OF FABRICS AND TUB WHEN THE DRYER DOOR IS

OPENED. ON THE DISPLAY THE ACTUAL TEMPERA-

TURE IS DISPLAYED. BEFORE ALL INTERVEN-

TIONS, TO PREVENT BURNS WAIT UNTIL THE HOT

PARTS HAVE COOLED.

C136

WARNING

THE ERROR MESSAGE TOO HOT CAN ALSO AP-

PEAR AT THE END OF A CYCLE EVEN IF NO FAIL-

URE HAS OCCURED AS AN EXAMPLE, DRYING CY-

CLE WITH A SHORT COOLDOWN TIME. AT THE END

OF SUCH A DRYING CYCLE, THE TEMPERATURE IN

THE TUB WILL STAY HIGH FOR A WHILE IF THE

COOLDOWN SEQUENCE WAS TOO SHORT. THE

CONTROL DRYER COMPUTER WILL GIVE A WARN-

ING THAT THE TEMPERATURE IS STILL HIGH.

C137

DEPENDING ON THE FAILURE TYPE THE FULL CON-

TROL COMPUTER WILL START A SPECIFIC PROCE-

DURE :

• WHEN SAFETY IS INVOLVED

• Full stop : the program is stopped.

• Full stop + cooldown : the program is stopped but a cooldown sequence is started.

• Don’t start : the program will not be started as long as the safety conditions are not fulfilled.

• WHEN SAFETY IS NOT INVOLVED

• Full stop + request for continue : a request to Continue ?

the program is displayed.

DO NOT COPY or TRANSMIT

41 Part No. D1707ENR4

Troubleshooting

• Skip + continue : the actual cycle step is skipped and the program continues with the next step.

• Continue : the program continues.

SPECIAL CASES :

• For E19, 20: Defective Temperature sensor and E35: Wrong software version The Failure message can only be erased by switching the power off and back on.

• Fault 41: Service Due will occur over and over again until you have reset the cycle counter. Refer to Paragraph

Failure

Message Overview how to reset the cycle counter.

RESET KEY :

• When you have overruled an error message and opened the door, Reset Key will be displayed.

• This message warns the operator that the programming switch is still in Program mode.

• Before you can start a new program you have to switch the programming switch back to Run mode.

! ! Reset Key ! !

» Switch the programming switch to Run mode.

MESSAGE “CLOSE THE LINT FILTER DOOR”

• This message indicates that the lint filter door is open during machine operation.

Failure Message Overview

• Close the lint filter.

• If the message keeps showing even after the door has been closed, check the power feed of the controller board and the fuses.

Clean Filter

UNLOAD CLEAN FILTER

• It’s a good attitude to clean the Lint Filter each day. (Refer to also Installation and maintenance manual).

• As safety is involved, when the Lint Filter has not been cleaned sooner then 15 succeeding cycles, a warning will be displayed at the end of the drying cycle. „CLEAN FILTER“

• As the amount of lint depends on the kind of fabrics it’s possible to adjust the number of cycles, for which the warning is generated, in the Configuration menu.

• Only by opening the lint door the Lint Filter Door Cycle

Counter will be reset.

• By opening the Dryer Door the warning on the display is erased but the Lint Filter Door Cycle Counter is not reset.

• You can check the Lint Filter Door Cycle Counter at the Running State-Service Menu which is accessible by the special function button on the keypad. (Press ARROW RIGHT button to go to the next menu item.) (Only valid for machines executed with an electric contact at the Lint Door)

N° Fault Occurrence

Whole cycle

E10

Failure Message

Heating Safety 1

Heating Safety 2

Motor Thermic

Fan Motor Thermic

Drum Motor Thermic

Airflow switch Open at

Startup

Airflow switch Open after

Startup

Airflow switch Closed

Failure Action

Heated air too hot

Heater too hot

Motor Security Trips

Heating Off, Full Stop at safe temperature

Fan Motor Security Trips Heating Off, Full Stop at safe temperature

Drum Motor Security Trips Heating Off, Full Stop at safe temperature

Airflow switch at start-up Heating Off Full Stop at safe temperature

Airflow switch after startup Heating Off Full Stop at safe temperature

Airflow switch failure before start-up

Don’t start

Whole cycle

Motor contactor on

At Start-up

Whole Cycle after Start-up

At Start-up

Table continues...

DO NOT COPY or TRANSMIT

42 Part No. D1707ENR4

E25

E26

E27

E28

E29

E35

E37

E41

E19

E20

E21

E22

E23

E24

E11

N°

E12

E13

E14

E15

E16

E17

E18

Troubleshooting

Failure Message Failure Action

Fault Cool down

No Reheating

No Heating

Heat Time

Too Hot

Coin Blocking 1

Coin Blocking 2

Too Hot Safety

No temperature drop at cool down

Heating not restarted

Heating Off,

Heating failure

Heating time failure

Too Hot

Heating Off,

Heating Off, Full Stop at safe temperature

Temp. too high (risk of burn!)

Heating Off, Full Stop at safe temperature Major

Alarm

Continue + Don’t start Defective Temperature sensor 1

Defective Temperature sensor 2

Heating element overheating

Ignition Error at Start-up

Value out of range

Safety Heating element trips

Ignition fails 3 times

Ignition Error after Start-up Ignition fails 3 times

Continue + Don’t start

Heating Off, Full Stop at safe temperature

Don’t start

Heating Off, Full Stop at safe temperature

Ignition Error Failure

No Humidity Sensor Humidity Sensor not connected

No Humidity Sensor Cap Cap Humidity Sensor missing

No Humidity Reduction

Wrong Ignition Error Signal

Lint Filter

Time out no reduction humidity value

Lint Filter has not been opened for 40 cycles

Continue, for info only saved in Err log.

Heating Off, Full Stop at safe temperature

Don’t start

TimeOut Cool

Wrong Softw

Too Hot Safety

Service Due

No Cool down

Wrong software version

Temp. too high (risk of burn!)

Service Due Warning

Heating Off, Full Stop at safe temperature

Don’t start

Major Alarm + Extra Cool down Time

For Info only Open door = reset

Fault Occurrence

At Cool down sequence

At Heating sequence

Before Start-up

Whole cycle

At Start Up

Whole cycle

No Heating

Whole cycle

At Start Up

At Cool down

New software version

Whole cycle

End cycle

Table continues...

DO NOT COPY or TRANSMIT

43 Part No. D1707ENR4

Troubleshooting

N° Failure Message

E150-E165 Memory Err

E170-E199 Softw Err

Failure

Memory Error

Software Error

Service Menu

In the Service menu you have some extra utilities:

• The Software Version Number

• An overview of the 8 last failure messages

• Statistics for general occurence of error messages

• An overview of the input states

• Reset Cycle Counter and Statistics Error Messages

HOW TO GET INTO THE SERVICE MENU

The SERVICE menu can only be accessed when the machine is in standby (the power is switched on, but no program is started).

• SELECT Process_ _ is displayed.

• Switch the programming switch to Program Mode.

• The Main menu is now available.

• Press the ARROW RIGHT button to select the SERVICE menu.

Main Menu Service

• Press the ENTER button to make your selection.

• Now you will see the first menu item.

• By pressing the ARROW LEFT or RIGHT button you can see the menu items one by one.

S:Software Version

1.00

• The Software Version number.

• You can select the next menu item by pressing the

ARROW RIGHT button.

S:View Fault Messages?

• If you don‘t want to see the

Fault messages, press the

ARROW RIGHT button.

• If you want to see the Fault messages, press the EN-

TER button.

DO NOT COPY or TRANSMIT

Action

Full stop + safety time

Fault Occurrence

Any time

S:Fault N° 1 :

EXXX:YYYYYYYY

S:Erase Fault Messages? No

S:View Fault Statistics?

• There are 8 Fault Messages kept in EEPROM memory.

• Fault N° 1 : the last occurred error message.

• Fault N° 2 : the last –1 occurred error message.

• …

• Fault N° 8 : the last – 7 occurred error message.

• E XXX : The Error message number.

• YYYYYYYYYY : The Error message name.

• Press the ARROW RIGHT button to see message by message and to leave the

Error message menu.

• If no messages are displayed, this means that no

Errors have occurred.

• If you don‘t want to erase the Fault messages, press the ARROW RIGHT button.

• Press the YES and ENTER button if you want to erase the Error messages.

• If you don‘t want to see the

Fault statistics, press the

ARROW RIGHT button.

• If you want to see the Fault statistics, press the ENTER button.

• The Fault Statistics are an accumulation of Errors messages that have appeared over a long period.

• The Statistics can be reset at the Service Menu, by a

Reset of the Cycle counter.

• With this information the technician has an indication on which parts an intervention will be needed.

Part No. D1707ENR4

S:Heating Safety 1

0 x

S:View Input States ?

• The List with Statistics.

• Heating Safety 1 : E1

• Heating Safety 2 : E2

• Motor Thermic : E5 + E6 +

• Air Flow Switch : E8 + E9

+ E10

• Fault Cooldown : E11

• No Heating : E12 + E13 +

E14

• Too Hot : E15 + E18

• Temperature Sensor : E19

+ E20

• Gas Ignition Error Run :

E23

• Gas Ignition Error Start :

E22

• If you don‘t want to see the

Input States, press the AR-

ROW RIGHT button.

• If you want to see the Input

States, press the ENTER button.

S:Input 1 Off/On

S:Reset Cycle Counter : No

Troubleshooting

• Input 1 : the State that corresponds with Input 1.

• Input 2 : the State that corresponds with Input 2.

• …

• Input 20 : the State that corresponds with Input 20.

• Analog Input 1, 2, 3 : the value that corresponds with

Analog Input 1, 2, 3.

• The exact function of the inputs can be found on the electrical drawing of the

FULL CONTROL Dryer.

• If the Input state is Off, the

Input signal is low.

• If the Input state is On, the

Input signal is high.

• Press the ARROW RIGHT button to see message by message and to leave the

Input state menu.

• To avoid that No maintenance will be fulfilled when the machine has reached the number of cycles that corresponds with the „Service Interval _ _

_“ number at the Initialization menu, a warning will be generated over and over again at the end of each cycle until the Cycle Counter at the Service menu has been reset.

• Also the Statistics for Error messages will be Reset by resetting the Cycle counter.

• If you don‘t want to reset the Cycle Counter, press the ARROW RIGHT button.

• Press the ARROW UP

„Yes“ and ENTER button if you want to reset the Cycle Counter.

DO NOT COPY or TRANSMIT

45 Part No. D1707ENR4

Troubleshooting

S: Service Menu Exit

• Press the ENTER button if you want to leave the

SERVICE Menu.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

Diagnostic Program

The purpose of the diagnostic program is to test the dryer machine functions one by one.

HOW TO GET INTO THE DIAGNOSTIC MENU

The Diagnostic menu can only be accessed when the machine is in standby (the power is switched on, but no program is started).

• Select Process_ _ is displayed.

• Switch the programming switch to Program Mode.

• The Main menu is now available.

• Press the ARROW RIGHT button to select the Diagnostic menu.

Main Menu Diagnostic

• Press the ENTER button to make your selection.

D:Diagnostic Program : No

S: Diagnostic Menu

Exit

• If you don’t want to start a diagnostic program, you have to press the ARROW

RIGHT button.

• Press the YES and ENTER button if you want to start the diagnostic program.

• Press the ENTER button if you want to leave the Diagnostic Menu.

NOTE: With the ARROW

LEFT button you can go back to a previous menu item.

TEST SEQUENCE

• Display test

• Sensor test

• Door test

• Motor test

• Heating test

DO NOT COPY or TRANSMIT

46 Part No. D1707ENR4

Troubleshooting

Problem Cause Solving the problem

When the power is switched on : the display is not illuminated

IMPORTANT: The display must always light up when the power connector is connected to the power board (EPROM with software must be implemented)

The display is illuminated, but it’s difficult to read the text on the display

The machine is not starting up

The machine is not responding on pressing the keyboard buttons

No external power

The emergency stop button is activated

The power connector is not connected on the board

Check voltage on the power supply connector

The brightness is not Ok

Switch on the external power supply verify the external power to the machine

Deactivate the emergency stop button

Connect the power connector

Check fuses in the power supply circuits of the control board. Remove the fuses after the cause of the fault has been rectified

(short circuit / faulty control board).

If there is no EPROM implemented on the logic board, put the right EPROM with software into the socket

Change the value for Brightness in the

Configuration Menu until you get a bright display.

Set the programming switch to “Run mode“

The programming switch stands in “Program mode“

The programming switch is not functional Check if the input connector “A“ is well connected and check the wiring between the input connector and the programming switch

The „START“ button is not functional (the programming switch stands in Program mode) set the programming switch to “Run mode“

Check if the connector “K“ of the keyboard is well connected

No button is functional and the programming switch is in the right position

There is no beep signal when the buttons are pressed

The machine is not behaving as expected If the wrong machine type is selected the wrong outputs will be activated

A program is started, but the outputs are not activated

Check if connector “R“ and “S“ are connected

Check if the right machine type is selected in the Configuration Menu.

Connect the connector at the correct position

Door must be closed

Heating safety must be closed

Motor safeties must be closed

Wait is displayed and a counter is counting down

This is a wait state caused by a power interruption or a safety sequence at the end of the process

Wait until the counter has reached 0 do not switch off/on the power again as you will restart the counter

Table continues...

DO NOT COPY or TRANSMIT

47 Part No. D1707ENR4

Troubleshooting

Problem Cause Solving the problem

Unload is displayed and the Door is Open Check if the „Door Switch“ is still closed If the „Door Switch“ is broken, replace the

Door Switch“

The drum is not turning

(No error message will be generated if there is no rotation sensor)

Check if the belt is broken

Check the applied motor voltage

Check if the motor is still functional

Check the tension of the belt or replace the belt

Repair the motor power supply circuit

Change the motor if needed

Error Message Descriptions

Failure 1: Heating Safety 1

Failure 1 occurs when the electronic timer detects that the heating safety located at the air outlet has opened it’s NC contact.

(NC thermal contact) (failure 1 can only occur when the drying cycle is running).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 1

1. Check the air outlet system. If the airflow is not sufficient, adjust the air outlet system.

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

3. Check the heating system.

If the heating system is broken repair, replace the heating system.

4. Check the heating contactor

(valve).

If the heating contactor (valve) is not functional repair or replace the component.

5. Check the wiring.

6. If the heating safety is not closing within 15 minutes.

7. Check the output relay that controls the heating system.

If the wiring is damaged, repair the wiring.

The heating safety is broken and must be replaced.

8. Check the input Signal by monitoring the state at the

Service menu.

If the output relay is not functional, replace the control board.

If the input is not functional anymore, replace the control board.

Table 18

Failure 2: Heating Safety 2

Failure 2 occurs when the electronic timer detects that the heating safety located at the heater has opened it’s NC contact. (NC thermal contact) (failure 2 can only occur when the drying cycle is running).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 2

1. Check the air outlet system. If the airflow is not sufficient, adjust the air outlet system.

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

3. Check the heating system.

If the heating system is broken repair, replace the heating system.

4. Check the heating contactor

(valve).

If the heating contactor (valve) is not functional repair or replace the component.

5. Check the wiring.

6. If the heating safety is not closing within 15 minutes.

7. Check the output relay that controls the heating system.

If the wiring is damaged, repair the wiring.

The heating safety is broken and must be replaced.

8. Check the input Signal by monitoring the state at the

Service menu.

If the output relay is not functional, replace the control board.

If the input is not functional anymore, replace the control board.

Table 19

Failure 5: Motor Thermic

Failure 5 occurs when the motor temperature (overcurrent) security has tripped. The contact will be closed again automatically after some time. (Failure 5 occurs for 1 motor machines). (NC thermal contact).

DO NOT COPY or TRANSMIT

48 Part No. D1707ENR4

Troubleshooting

A skilled and experienced technician must examine the motordrive system before the machine is put in operation again.

Diagnosing Failure 5

Diagnosing Failure 6

1. Check if the thermal security of the motor is open.

If the thermal security is open, within 15 minutes the security will close automatically.

If a motor is defective, the security can go open again when you restart the dryer.

If it was only a temperature problem, and the motor is not defective: the overload security will not trip again.

2. Check that the airflow, drum and ventilator rotation is not obstructed.

Solve the mechanical problem.

3. If the thermal motor security is not closing after 15 minutes.

The thermal motor security might be broken.

4. Check the continuity of the wiring.

5. Check the input signal by monitoring the state at the

Service menu.

If the wiring is not continuous: repair the wiring.

If the input is not functional anymore, replace the control board.

Table 20

Failure 6: Fan Motor Thermic

Failure 6 occurs when the fan motor temperature (overcurrent) security has tripped. The contact will be closed again automatically after some time. (Failure 6 occurs only for 2 motor machines). (NC thermal contact).

A skilled and experienced technician must examine the motordrive system before the machine is put in operation again.

1. Check if the thermal security of the motor is open.

If the thermal security is open, within 15 minutes the security will close automatically.

If a motor is defective, the security can go open again when you restart the dryer.

If it was only a temperature problem and the motor is not defective: the overload security will not trip again.

2. Check that the airflow, drum and ventilator rotation is not obstructed.

Solve the mechanical problem.

3. If the thermal motor security is not closing after 15 minutes.

The thermal motor security might be broken.

4. Check the continuity of the wiring.

5. Check the input signal by monitoring the state at the

Service menu.

If the wiring is not continuous, repair the wiring.

If the input is not functional anymore, replace the control board.

Table 21

Failure 7: Drum Motor Thermic

Failure 7 occurs when the motor temperature (overcurrent) security has tripped. The contact will be closed again automatically after some time. (Failure 7 occurs only for 2 motor machines) (NC thermal contact).

A skilled and experienced technician must examine the motordrive system before the machine is put in operation again.

Diagnosing Failure 7

1. Check if the thermal security of the motor is open.

If the thermal security is open, within 15 minutes the security will close automatically.

If a motor is defective, the security can go open again when you restart the dryer.

If it was only a temperature problem and the motor is not defective: the overload security will not trip again.

Table 22 continues...

DO NOT COPY or TRANSMIT

49 Part No. D1707ENR4

Troubleshooting

Diagnosing Failure 7

2. Check that the airflow, drum and ventilator rotation is not obstructed.

Solve the mechanical problem.

3. If the thermal motor security is not closing after 15 minutes.

The thermal motor security will be probably broken.

4. Check the continuity of the wiring.

5. Check the input signal by monitoring the state at the

Service menu.

If the wiring is not continuous, repair the wiring.

If the input is not functional anymore, replace the control board.

Table 22

Failure 8: Airflow Switch Open at Start-up

Failure 8 occurs when there is not sufficient airflow when the ventilator is switched On. This security function prevents the heating is switched On when the ventilator is not functional or if the airflow is obstructed.

(Failure 8 occurs only at start-up) (NO contact).

The Airflow Switch has a safety function and it must not be obstructed.

A skilled and experienced technician must examine the dryer system before the machine is put in operation again.

WARNING

For new installations the air outlet tubes must have the right size for the air flow of the corresponding machine. Follow the instructions in the installation manual.

C138

Diagnosing Failure 8

1. Check if the ventilator is functional.

2. Check if there is sufficient airflow. Check if the Dryer is a closed box. (Lint filter Door, mechanical panels must be present and closed properly).

If the ventilator is not functional, repair or replace the ventilator, belt, motor control system, wiring or the power supply circuit of the ventilator.

In normal operation, the Ventilator is switched On immediately after pressing the

START button.

The ventilator must stay on for the entire drying cycle.

When the Dryer is not a closed box, air will escape and the airflow will not be sufficient to switch the Airflow Switch.

Make sure that there is no loss of Airflow.

Example : close the Lint Filter Door properly.

3. Check if the switch and metal plate and airflow detection system is still functional.

4. Check the continuity of the wiring

5. Check the input signal by monitoring the state at the

Service menu.

Table 23

If the airflow detection system or the switch is out of order, it must be repaired or replaced.

If the wiring is not continuous: repair the wiring

If the input is not functional anymore, replace the control board.

Failure 9: Airflow Switch Open After Start-up

Failure 9 occurs when there is not sufficient airflow when the ventilator is turning. This security function makes the heating switch Off when the ventilator is suddenly Not functional anymore or if the airflow gets obstructed.

(Failure 9 occurs only after start-up) (NO contact).

The Airflow Switch has a safety function and it must not be obstructed.

A skilled and experienced technician must examine the dryer system before the machine is put in operation again.

DO NOT COPY or TRANSMIT

50 Part No. D1707ENR4

Troubleshooting

Diagnosing Failure 9 Diagnosing Failure 10

1. Check if the ventilator is functional.

If the ventilator is not functional, repair or replace the ventilator, belt, motor control system, wiring or the power supply circuit of the ventilator.

In normal operation, the Ventilator is switched On immediately after pressing the

START button.

The ventilator must stay on for the complete time of the drying cycle.

1. Check if the airflow detection system is still functional.

2. Check if the ventilator is switched On immediately after pressing start.

3. Check the continuity of the wiring.

4. Check that the ventilator is switched Off at the end of the drying cycle.

5. Check the input signal by monitoring the state at the

Service menu.

Table 25

If the airflow detection system or the switch is out of order, it must be repaired or replaced.

Check the contactor, wiring and the ventilator command signal.

If the wiring is not continuous, repair the wiring.

If the contactor is not correctly functioning, replace the contactor.

If the input is not functional anymore, replace the control board.

2. Check if there is sufficient airflow. Check if the Dryer is a closed box. (Lint filter Door, mechanical panels must be present and closed properly).

When the Dryer is not a closed box, air will escape and the airflow will not be sufficient to switch the Airflow Switch.

Make sure that there is no loss of Airflow.

Example: close the Lint Filter Door properly.

3. Check if the switch and metal plate and airflow detection system is still functional.

4. Check the continuity of the wiring

5. Check the input signal by monitoring the state at the

Service menu.

Table 24

If the airflow detection system or the switch is out of order, it must be repaired or replaced.

If the wiring is not continuous, repair the wiring.

If the input is not functional anymore, replace the control board.

Failure 10: Airflow Switch Closed

Failure 11: Fault Cool down

Failure 11 occurs when the temperature does not decrease when the Cooldown sequence is in progress. (No cooldown at all after

15 minutes at cool down sequence for temperature above 122°F

[50°C]).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 11

1. Check if the heating system is switched Off.

If no temperature ramp has been programmed for the cool down sequence, the heating system must be switched Off.

Check the contactor (valve), wiring, and the ventilator command signal.

Failure 10 occurs at the start of the drying cycle. Before the ventilator is switched On, the Airflow switch must be open. If the flow detection system is out of order, and the switch is closed, an error message will be displayed.

(Failure 10 occurs only in standby mode) (NO contact).

The Airflow Switch has a safety function and it must not be obstructed.

A skilled and experienced technician must examine the dryer system before the machine is put in operation again.

2. Check if the temperature sensor is functional.

3. Check the output relay that controls the heating system.

Table 26

Failure 12: No Reheating

If the temperature sensor is not measuring correctly, replace the temperature sensor.

If the output relay is not functional, replace the programmer board.

Failure 12 occurs at a heating (cooldown with ramp) sequence when the heating is not switched On again at the temperature

DO NOT COPY or TRANSMIT

51 Part No. D1707ENR4

Troubleshooting control process when the lowest temperature hysteresis value is reached.

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 12

1. Check if there is no interruption of the electrical power, gas or steam heating power supply.

2. Check if the heating system is functional.

3. Check the heating contactor

(valve).

4. Check the continuity of the wiring.

5. Check if the temperature sensor is functional.

6. Check the output relay that controls the heating system.

The machine will not heat when there is no energy supply for the heating system. Avoid interruptions of the energy supply.

If the heating system fails to work, repair or replace the heating system.

If the heating contactor (valve) is not functional, repair or replace the component.

If the wiring is not continuous: repair the wiring.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

If the output relay is not functional, replace the control board.

Table 27

Failure 13: No Heating

Failure 13 occurs when the heating system is not functional at start up. (No temperature raise of 41°F [5°C] in 30 minutes after start drying cycle.)

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 13

1. Check if there is no interruption of the electrical power, gas or steam heating power supply.

2. Check if the heating system is functional.

3. Check the heating contactor

(valve).

The machine will not heat when there is no energy supply for the heating system. Avoid interruptions of the energy supply.

If the heating system fails to work, repair or replace the heating system.

If the heating contactor (valve) is not functional, repair or replace the component.

Table 28 continues...

Diagnosing Failure 13

4. Check the continuity of the wiring.

5. Check if the temperature sensor is functional.

6. Check the output relay that controls the heating system.

If the wiring is not continuous, repair the wiring.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

If the output relay is not functional, replace the control board.

Table 28

Failure 14: Heat time

Failure 14 occurs when after X minutes the target temperature is not reached.

The alarm time X can be set in the initialisation menu. (For setting 99, no Error message 14 will occur) The information serves as an indication of reduced heating power.

Diagnosing Failure 14

1. Check if there is no interruption of the electrical power, gas or steam heating power supply

The machine will not heat when there is no energy supply for the heating system. Avoid interruptions of the energy supply.

2. Check the heating system.

If the heating system fails to work, repair or replace the heating system.

3. Check the heating contactor

(valve)

4. Check the continuity of the wiring.

5. Check if the temperature sensor is functional.

If the heating contactor (valve) is not functional repair or replace the component.

If the wiring is not continuous, repair the wiring

6. Check the output relay that controls the heating system.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

If the output relay is not functional, replace the control board.

Table 29

Failure 15: Too Hot

Failure 15 occurs when the actual heating temperature goes 59°F

[15°C] above the target temperature at the drying process.

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

DO NOT COPY or TRANSMIT

52 Part No. D1707ENR4

Troubleshooting

Diagnosing Failure 15 Diagnosing Failure 18

1. Check the air outlet system. If the airflow is not sufficient, adjust the air outlet system.

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

3. Check the heating system.

If the heating system is broken, repair or replace the heating system.

4. Check the heating contactor

(valve).

If the heating contactor (valve) is not functional, repair or replace the component.

5. Check the wiring.

6. Check the output relay that controls the heating system.

If the wiring is damaged, repair the wiring.

If the output relay is not functional, replace the control board.

7. Check the input Signal by monitoring the state at the

Service menu.

If the input is not functional, replace the control board.

Table 30

Failure 18: Too Hot Safety

Failure 18 occurs when the actual heating temperature rises above safety temperature 185°F [85°C ] while the machine is waiting to be started (not running).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

3. Check the heating system.

If the heating system is broken, repair or replace the heating system.

4. Check the heating contactor

(valve).

If the heating contactor (valve) is not functional, repair or replace the component.

5. Check the wiring.

6. Check the output relay that controls the heating system.

If the wiring is damaged, repair the wiring.

If the output relay is not functional, replace the control board.

7. Check the input Signal by monitoring the state at the

Service menu.

If the input is not functional anymore, replace the control board.

Table 31

Failure 19: Defective Temperature Sensor 1

Failure 19 occurs when the temperature sensor (located at the air outlet) is broken . The fault is only displayed when the machine is in standby mode and no program is active.

The fault can only be erased by switching off and on the power. If the fault is still present after switching on the power fault message 19 will be generated again.

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 19

WARNING

IF FAILURE 18 OCCURS WE CAN EXPECT THERE IS

RISK OF BURN AND NECESSARY ACTIONS MUST

BE TAKEN TO REDUCE TEMPERATURE.

C139

Diagnosing Failure 18

1. Check the air outlet system. If the airflow is not sufficient, adjust the air outlet system.

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

Table 31 continues...

1. Check if the temperature sensor is connected on the

PCB Board.

2. Check the temperature sensor.

3. Measure the resistance of the sensor.

4. Check if the earth wire is at the middle position of the connector.

5. If the fault is persistent.

The Female connector must be connected with the Male connector T1 of the PCB board.

If the temperature sensor is broken, replace the temperature sensor.

If the resistance is not OK, replace the temperature sensor.

If the earth wire is not at the middle position, put the earth wire in the middle position of connector T1.

Replace the electronic board.

Be sure the problem is related to the electronic board and not to a defective temperature sensor.

Table 32

DO NOT COPY or TRANSMIT

53 Part No. D1707ENR4

Troubleshooting

Failure 20: Defective Temperature Sensor 2

Diagnosing Failure 22

Failure 20 occurs when the temperature sensor (located at the heater) is broken. The fault is only displayed when the machine is in standby mode and no program is active.

The fault can only be erased by switching off and on the power. If the fault is still present after switching on the powe, fault message 20 will be generated again.

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 20

1. Check if the temperature sensor is connected on the

PCB Board.

2. Check the temperature sensor.

3. Measure the resistance of the sensor.

4. Check if the earth wire is at the middle position of the connector.

5. If the fault is persistent.

The Female connector must be connected with the Male connector T2 of the PCB board.

If the temperature sensor is broken, replace the temperature sensor.

If the resistance is not OK, replace the temperature sensor.

If the earth wire is not at the middle position, put the earth wire in the middle position of connector T2.

Replace the electronic board.

Be sure the problem is related to the electronic board and not to a defective temperature sensor.

Table 33

1. Check the gas supply.

Without gas supply, the heater can not function. Right Gas supply and pressure must be available.

2. Check the heating system.

If the heating system is broken, repair replace the heating system.

3. Check the gas ignition system.

If the gas ignition system is not functional, replace the gas ignition system.

4. Check the heating contactor. If a heating contactor is not functional, replace the component.

5. Check contactor KA3 (Ignition Error).

6. Check the wiring.

If the contactor KA3 is not functional, replace the component.

If the wiring is damaged, repair the wiring.

7. Check the output relays that control the heating system.

8. Check the electrical Input

Ignition Error at the control board.

If an output relay is not functional, replace the control board.

If the input of the control board is not functional anymore, replace the control board.

Table 34

Failure 22: Ignition Error at Start-up (GAS

HEATING ONLY)

Failure 22 occurs when the heating system has a problem to switch on the fire at start up.

If the problem is still persistent after 3 automatic resets, error message 22 is generated.

The gas ignition system closes contactor KA3 (input 4 High) to inform the dryer computer that the gas ignition system failed to switch on the fire.

Then the ignition system is reset by the dryer computer by switching on the reset signal gas ignition system (contactor

KA2).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Failure 23: Ignition Error After Start-up (Run) (GAS

HEATING ONLY)

Failure 23 occurs when the heating system has a problem to switch on the fire when the dryer tries to restart the gas heating system. (While the dry cycle is running).

If the problem continues after 3 automatic resets, the operator is invited to restart the system.

If the action of the operator is not successful, error message 23 is generated.

The gas ignition system closes contactor KA3 (input 4 High) to inform the dryer computer that the gas ignition system failed to switch on the fire.

Then the ignition system is reset by the dryer computer by switching on the reset signal gas ignition system (contactor

KA2).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

DO NOT COPY or TRANSMIT

54 Part No. D1707ENR4

Diagnosing Failure 23 Diagnosing Failure 24

1. Check the gas supply.

Without gas supply, the heater can not function. Right Gas supply and pressure must be available.

2. Check the heating system.

If the heating system is broken, repair replace the heating system.

3. Check the gas ignition system.

If the gas ignition system is not functional, replace the gas ignition system.

4. Check the heating contactor. If a heating contactor is not functional, replace the component.

5. Check contactor KA3 (Ignition Error).

6. Check the wiring.

If the contactor KA3 is not functional, replace the component.

If the wiring is damaged, repair the wiring.

7. Check the output relays that control the heating system.

8. Check the electrical Input

Ignition Error at the control board.

If an output relay is not functional, replace the control board.

If the input of the control board is not functional, replace the control board.

Table 35

Failure 24: Ignition Error Failure (GAS HEATING

ONLY)

Failure 24 occurs after 3 attempts when the Gas Ignition system fails to be reset.

Cause: Input Signal Ignition Error Failure stays high (Input 4) after 3 attempts of dryer computer to reset gas ignition system

(contactor KA2). This is to be considered a major hardware failure.

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 24

1. Check the gas ignition system.

2. Check the wiring.

If the gas ignition system is broken, replace the gas ignition system.

If the wiring is damaged, repair the wiring.

Table 36 continues...

3. Check contactor KA3 (Ignition Error).

4. Check the electrical Input

Ignition Error at the control board.

Table 36

If the contactor KA3 is not functional, replace the component.

If the input of the control board is not functional, replace the control board.

Failure 25: No Humidity Sensor (HUMIDITY

CONTROL ONLY)

Failure 25 occurs when the humidity sensor does not give an analog electrical output signal to the dryer computer.

Example: connector not connected to dryer computer.

(At the “Configuration“ menu you can switch off/on the Humidity Control function).

NOTE: The humidity sensor needs 1 minute after switching on the power supply dryer to stabilize the analog output signal.

Failure 25 can occur when the dryer is running without linens inside. This should not be considered as a system failure. Check correct dryer operation with a normal amount of wet linen.

WARNING

THE HUMIDITY CONTROL SYSTEM IS NOT MADE TO

RUN WITHOUT LOAD OR WITH A VERY SMALL

LOAD. THE SYSTEM CAN ONLY FUNCTION IN A

NORMAL WAY WHEN THERE IS SUFFICIANT EVAP-

ORATION TO BE MEASURED BY THE AIR HUMIDITY

SENSOR.

C133

Diagnosing Failure 25

1. Check if the humidity sensor is connected to the dryer computer.

2. Check the wiring.

3. Check the supply voltage humidity sensor.

If the humidity sensor is not connected to the dryer computer, connect the sensor.

If the wiring is damaged, repair the wiring.

If there is no, or wrong supply voltage, replace the dryer computer.

4. Check the humidity sensor and amplifier.

If the humidity sensor or amplifier is damaged, replace the humidity sensor and amplifier.

Table 37 continues...

DO NOT COPY or TRANSMIT

Troubleshooting

Part No. D1707ENR4

Troubleshooting

Diagnosing Failure 25 Diagnosing Failure 28

5. Check the analog input signal.

(Inputs can be checked, one by one, in the Service menu).

CONTROL ONLY)

If for Analogue value 3, the value at the Analog input menu = “0“ then the analog input signal is missing.

If the input of the controller board is not functional, replace the controller board.

(first check previous items)

Table 37

Failure 26: No Humidity Sensor Cap (HUMIDITY

Failure 26 occurs when the dust cap at the humidity sensor is missing.

When the dust cap is missing, due to the influence of the air flow in the dryer, the sensor will measure a too big value which is out of range at normal operation.

(At the “Configuration“ menu you can switch off/on the Humidity Control function).

NOTE: The humidity sensor needs 1 minute after switching on the power supply dryer to stabilize the analog output signal.

WARNING

1. The Lint Filter must be cleaned every day.

2. Check if the Lint Filter

Door Cycle Counter is reset by opening the Lint Door.

If the Lint Filter has not been cleaned for 40 days, open the

Lint Door and clean the Filter.

Close the door again. The Lint

Filter Door Cycle will be reset.

If the Lint Filter Door Switch is broken, replace the Lint Filter Door Switch. (Normal

Closed Contact.)

If the wiring is broken, repair the wiring.

3. Check if the Lint Filter

Door Cycle Counter is reset by opening the Lint Door.

4. Check if the Lint Filter

Door Cycle Counter is reset by opening the Lint Door.

If the input of the control board is not correctly functioning, replace the control board.

Table 38

Failure 29: Timeout Cooldown

Failure 29 occurs when the Cooldown temperature is not reached in max. allowed time (120 minutes) (Temperature selected at

Cooldown sequence)

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

Diagnosing Failure 29

IF THE DRYER IS EXECUTED WITH AIR HUMIDITY

SENSOR, THE DRYER CAN ONLY OPERATE COR-

RECTLY IF THE DUST CAP IS MOUNTED ON THE

AIR HUMIDITY SENSOR.

C141

Failure 27: No Humidity Reduction

Failure 27 occurs when the humidity value does not decrease within 60 minutes when the drying sequence is in progress.

(Maximum drying time by humidity control is set default on 60 minutes.)

Failure 28: Lint Filter

Failure 28 occurs when the Lint Filter Door has not been opened for 40 succeeding cycles.

Check value of the Lint Filter Door Cycle Counter at the Running

State-Service menu. (Special function button)

1. Check the air outlet system. If the air flow is not sufficient, adjust the air outlet system.

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

3. Check the heating system.

If the heating system is broken, repair or replace the heating system.

4. Check the heating contactor

(valve)

5. Check the wiring.

If the heating contactor (valve) is not functional repair or replace the component.

If the wiring is damaged, repair the wiring.

6. Check the output relay that controls the heating system.

7. Check the input Signal by monitoring the state at the

Service menu.

If the output relay is not functional, replace the control board.

If the input is not functional anymore, replace the control board.

Table 39

DO NOT COPY or TRANSMIT

56 Part No. D1707ENR4

Troubleshooting

Failure 35: Wrong Software Version

Diagnosing Failure 37

When a total new software that isn't downward compatible with previous software versions is loaded, then the software will detect that the old and new softwares are not compatible.You have to reconfigure the FULL CONTROL Dryer Computer. Refer to Initializing the machine.

WARNING

ALL THE CUSTOM SETTINGS WILL BE ERASED IN

THE CONTROL DRYER COMPUTER BY LOADING

THE FACTORY SETTINGS.

After reinitialization of the FULL CONTROL Dryer Computer, fault 35 can only be erased by switching the power Off/On.

Failure 37: Too Hot Safety

WARNING

Diagnosing Failure 37

C142

Failure 37 occurs when the actual heating temperature rises above safety temperature 185°F [85°C] while the machine is running.

(24kg / 53lb / 33 L & 35kg / 77lb / 46 L ELECTRICAL HEAT-

ING ONLY : 212°F [100°C])

If at the end of the drying cycle, the temperature is above 185°F

[85°C] (212°F [100°C]), the dryer will go on with the cool down sequence for 30 minutes (or until temperature below 149°F

[65°C] or until open door).

The display will show “Hot“, indicating something is wrong.

Check Safety Thermostats ST1 & ST2 as they should switch off the heating system and prevent high temperatures.

(Refer to Monitoring Temperature Values).

A skilled and experienced technician must examine the heating and air outlet system before the machine is put in operation again.

IF FAILURE 37 OCCURS WE CAN EXPECT THERE IS

RISK OF BURN AND NECESSARY ACTIONS MUST

BE TAKEN TO REDUCE TEMPERATURE.

C143

1. Check the air outlet system. If the airflow is not sufficient, adjust the air outlet system.

Table 40 continues...

2. Check the temperature sensor.

If the temperature sensor is not measuring correctly, replace the temperature sensor.

3. Check the heating system.

If the heating system is broken, repair or replace the heating system.

4. Check the heating contactor

(valve).

5. Check the wiring.

If the heating contactor (valve) is not functional, repair or replace the component.

If the wiring is damaged, repair the wiring.

6. Check the Safety Thermostats ST1 & ST2.

7. Check the output relay that controls the heating system.

8. Check the input Signal by monitoring the state at the

Service menu.

The Safety Thermostats should go open before failure 37 is generated.

If the output relay is not functional, replace the control board.

If the input is not functional, replace the control board.

Table 40

Failure 41: Service Due

Service Due Err message is an indication that there must be a maintenance intervention.

Consult the Installation - Maintenance manual about the kind of the intervention that is required.

Err message 41 is just for informational purposes and the machine can still be operated, but to get rid of the Err message, a reset of the cycle counter is required.

(At the Initialization menu, the Service Interval Count can be adjusted.)

» Go to the "Reset Cycle Counter" menu item in the Service

Menu.

• Select Yes to reset the cycle counter.

» Press the SERVICE-STATE button and select the corresponding screen to inspect the number of cycles that have been accumulated (service due).

Failure 95: Watch Dog

If the watch dog has been activated, message 95 is logged in the

Error log register. If this occurs often, ask the help of a technician.

DO NOT COPY or TRANSMIT

57 Part No. D1707ENR4

Troubleshooting

Failure 150-165: Memory Errors

If a memory error occurs, then something is wrong with the EE-

PROM.

Try to reload the Programs. Check for source of electrical

“noise“.

Failure 170-199: Sofware Errors

Software errors must never occur, if a software error message occurs, inform the manufacturer.

Humidity Control - Troubleshooting

The analogue value humidity sensor can be watched while drying the linen. This can be helpful for diagnostic purposes.

While dryer is running, programming switch in Program mode, press Status Button and Humidity Button and the analogue value humidity sensor is shown.

WARNING

THE HUMIDITY CONTROL SYSTEM IS NOT MADE TO

RUN WITHOUT LOAD OR WITH A VERY SMALL

LOAD. THE SYSTEM CAN ONLY FUNCTION IN A

NORMAL WAY WHEN THERE IS SUFFICIANT EVAP-

ORATION TO BE MEASURED BY THE AIR HUMIDITY

SENSOR.

C133

WARNING

CHECK CORRECT DRYER OPERATION WITH A

NORMAL AMOUNT OF WET LINEN.

C178

Troubleshooting problems with Humidity Control:

Operation with a small load of laundry

The humidity control system is not designed for operation without any load, or with a very small load. It is advisable to set the maximum dry time after which the drying operation will be terminated

• (Refer to chapter Programming the drying part).

Check dust filter cap

When humidity control does not work, check if the dust filter cap is missing. The dust filter cap is a white cover that must not be removed from the sensor device. The dust filter cap allows air to pass.

Check door lock system

When the dryer door is not completely closed, air from the room is sucked in the dryer. This causes a wrong air humidity measurement. Make sure the dryer can only run when the door is in the closed (locked) position. (When door is still 10 mm open, it should not be possible to start a dryer program.)

Check heating and airflow

The air humidity measurement can only function when there is sufficient water evaporation from the linen. Evaporation can only happen when the, air and indirectly the linen is sufficiently heated. If the dryer has to run with reduced heating power, the airflow must be sufficiently reduced so there is still evaporation.

Example:

• There is in sufficient Electrical Current available at the building.

• The dryer works with only 50% of it's electrical heating power.

• The airflow must be sufficiently reduced so there is still enough evaporation inside the dryer to allow optimal humidity control.

Check final drying temperature

At a normal drying process, the outlet air temperature reaches the programmed target value when the linen gets dry. For a correct drying process: when humidity control stops the dryer, the dryer must have reached, before the end of the drying cycle, the programmed target temperature value. If this is not the case, probably there will not have occured sufficient evaporation at the drying process because of reduced heating power. And the air humidity measurement will not have been accurate to allow optimal humidity control.

Linen must be sorted

A mixture of linen in the dryer can not result in an equal drying result. It is a good practice that the same kind of linen is sorted and dryed together, (Coton, Synthetic). In case of Humidity Control, a mixture of all kinds of linen will not give a good overall drying result.

Thin - Thick Fabrics

Thick fabrics, like jeans or trousers, need a long drying time.

Dryer program will stop when fabrics are mostly dry, but inside pockets will still feel damp. In case of thin fabrics, where the linen is sewed together there may be damp spots. Humidity Control stops the dryer when the linen is dry, based on the measured air humidity.

Correct Load in Drum

Some fabrics need more space in dryer than others. It is important to choose the right size of dryer to obtain a good airflow.

• If there is more linen in the drum, the airflow will be restricted and the linen will not be dried evenly.

DO NOT COPY or TRANSMIT

58 Part No. D1707ENR4

Service information

General

Service information

WARNING

VVV = Version

Programmer Circuit Board

Programmer Circuit Board

PROFESSIONAL REPAIRS IN ELECTRO INSTALLA-

TION CAN BE CARRIED OUT ONLY BY SERVICE OR-

GANIZATION WITH PERMISSION GIVEN BY PRO-

DUCER / SUPPLIER.

IN CASE OF ANY MAINTENANCE OR REPAIR DIS-

CONNECT THE MACHINE FROM SOURCE OF ENER-

GY AND WAIT UNTIL THE MACHINE COOLS DOWN.

PLEASE FOLLOW ALL INSTRUCTIONS IN THE MAN-

UALS AND THE LABELS AS WELL AS VALID BASIC

SECURITY LAWS IN ORDER TO PREVENT BURNS

AND SCALDS AND INJURIES CAUSED BY ELEC-

TRICITY, HEATING POWER SUPPLY, MECHANICAL

MOVING PARTS.

C145

Maintenance

Figure 4

Remove dirt from the keyboard by a damp cloth after disconnection from the power supply.

WARNING

Do not use aggresive soaps, caustic chemicals, gasoline or other petrochemical substances which can damage the keyboard.

C082

Follow the instructions from the installation-maintenance manual.

Information for Service

WARNING

Every circuit board has a sticker placed on the eprom, which specifies the version and the date of the software. This data along with the machine serial no., order code must be given in all correspondence or inquiries to the manufacturer.

C085

XXX-VVV

XXX = (Software for the FULL CONTROL dryer computer)

Connection to the wrong voltage supply may cause serious bodily injury as well as damage to the electronic parts and to the wasching machine itself.

C083

• Voltage : 200-240 Vac, 50/60 Hz

• Power : max 16 VA

• Memory :

• EPROM (contains the software)

• EEPROM (contains the customized programs)

• Outputs : 6 relays

• Serial interface : RS485 (2 wire) networking between dryer computer and external device (PC Computer)

• Display : LCD display

Instructions for Replacing the

Electronic Board and Keypad

• Switch off the main power supply.

• Open the front plate of the dryer.

• Turn the control board assembly holder to the front.

• Remove the connectors from the control board.

• Remove the combination keyboard - electronic timer by the rear side of the fascia panel.

DO NOT COPY or TRANSMIT

59 Part No. D1707ENR4

Service information

• Put the new combination keyboard – electronic timer into the machine and tighten the screws.

• Reconnect all the connectors.

• Turn the control board assembly holder back to its original position.

• Close the front plate of the dryer.

• Now you can Switch On the power supply.

• The display should illuminate.

WARNING

MAKE SURE THAT YOU DON’T DAMAGE THE FLEX

CABLE OF THE KEYPAD WHEN YOU PUT THE CON-

TROL DRYER COMPUTER BACK INTO THE MA-

CHINE.

C147

Instructions for Installing New Software

• Go through the Menu items of the Configuration and Initialization Menu one by one to ensure that all the settings do correspond with the ones you prefer.

• Switch the power Off/On.

• Now the FULL CONTROL Dryer computer is ready to start a new cycle.

• Switch off the main power.

• Open the front plate of the dryer.

• Turn the control board assembly holder to the front until you have access to the control board.

• The EPROM with the implemented software is the only IC on the logic board that can be removed.

• Take the EPROM out of the IC-holder (by a dedicated tool) and replace it by a new one.

• Make sure that you put the new chip at the right position. See picture.

• Turn the control board assembly holder back to its original position.

• Close the cover plate of the dryer.

• Switch on the main power.

• The display should illuminate.

• If the software is compatible with the previous software: the new software can be used without reinitialization.

• You have to clear all the error messages in the Service-menu, if you want to make a correct inspection of the functioning of the new installed software.

• If the software is not 100% compatible with the previous software version:

• The new software will generate a diagnostic message 35.

When fault message 35 occurs, you have to reset the settings of the configuration and initialization menu.

• This can be easily done by Selecting Reset Factory Settings in the Configuration Menu.

• » This is explained in Chapter: Basic Description of

Controls.

• All the Custom Settings will be lost.

DO NOT COPY or TRANSMIT

60 Part No. D1707ENR4

سلام! من یک ربات چت هوش مصنوعی هستم که به طور خاص برای کمک به شما در مورد Alliance T11 آموزش دیده‌ام. من سند را به طور کامل بررسی کرده‌ام و می‌توانم به شما کمک کنم اطلاعات دقیقی را که نیاز دارید پیدا کنید یا محتوا را به زبان ساده و واضح توضیح دهم. چه به دنبال راهنمایی در مورد ویژگی‌های خاص، مراحل عیب‌یابی یا استفاده عمومی باشید، می‌توانید سوالات خود را بپرسید. هرچه جزئیات بیشتری در مورد نگرانی‌ها یا نیازهای خود ارائه دهید، من می‌توانم دقیق‌تر و موثرتر به شما کمک کنم!

دستیار در حال تایپ

دستیار از صفحه کلید خارج شده است. لطفا بعدا دوباره امتحان کنید.

فهرست مطالب

تبلیغات

Tumble-Dryers

Full Control

Refer to Page

for Model Identification

Original Instructions

Keep These Instructions for Future Reference.

CAUTION: Read the instructions before using the machine.

www.alliancelaundry.com

Table of Contents

Safety Information

Important Safety Instructions

Introduction

Model Identification

Machine Type Selection

Symbols Used

Control Identification

Main Menu

Basic Description of Controls

General

Specific Information

20 Dryer Programs - 5 Steps

The Creation of a Dryer Program

Programming the Functions

Initializing the machine

Initialization Menu

Configuration Menu

Humidity Control

How to Create and Adjust a Dryer Program

Programming

General

Step 1: Program Menu

Step 2: Program Functions

Step 3: Program Step Functions

Step 4: Programming the Drying Part

Operation menu

Start Up

Advancing a Dryer Program

Switch On the Power

Load the Dryer

Start a Dryer Program

The Active Program

Drying Time

Program End

Cool-Down Function

Stop

How to Handle Power Interruptions

Wait State

How to Handle Failure Messages

Service-State Button

Pre-programmed programs

General

Drying Programs

Troubleshooting

Display Messages

Fault Messages

How to Handle Fault Messages

Failure Message Overview

Clean Filter

Service Menu

Diagnostic Program

Troubleshooting

Error Message Descriptions

Failure 1: Heating Safety 1

Failure 2: Heating Safety 2

Failure 5: Motor Thermic

Failure 6: Fan Motor Thermic

Failure 7: Drum Motor Thermic

Failure 8: Airflow Switch Open at Start-up

Failure 9: Airflow Switch Open After Start-up

Failure 10: Airflow Switch Closed

Failure 11: Fault Cool down

Failure 12: No Reheating

Failure 13: No Heating

Failure 14: Heat time

Failure 15: Too Hot

Failure 18: Too Hot Safety

Failure 19: Defective Temperature Sensor 1

Failure 20: Defective Temperature Sensor 2

Failure 22: Ignition Error at Start-up (GAS

HEATING ONLY)