VMOD66 - CAN-bus User Manual

VMOD66 - CAN-bus User Manual
FA L CON
WORLD CLASS SECURITY
FALCON PREDATOR
CAN-BUS ALARM
Advanced Alarm System for Vehicles with CAN-Bus
User Manual
NATIONWIDE INSTALLATION SERVICE
0800 622 474
HELPLINE: 0906 700 10 20
(All calls charged at 50p/min)
Internet: http://www.falcon-security.com
Email: [email protected]
A. System Operation.................................................................. 3
01. System arm ........................................................................... 3
02. System disarm ....................................................................... 4
03. Status LED indications............................................................ 5
04. Temporary sensor bypass....................................................... 5
05. Valet mode............................................................................. 6
06. System trigger and alarm........................................................ 6
07. Trigger and alarm clear ........................................................... 7
08. Remote boot open ................................................................. 8
B. System Programming............................................................ 9
01. Setting the optional features ................................................... 9
02. Optional feature table ........................................................... 10
C. Explanation of Optional Features........................................ 11
A. System Operation
01. System arm
The system can be armed as follows:
1. Press the lock button of factory remote
2. Passive arming
3. Auto re-arm
1. Press the lock button of factory remote
The operation is as follows:
1. With ignition off
2. The N.O immobiliser will be on if connected
3. AED will function within 20 or 30 sec. depending on the setting
of option #3
4. Close all the doors, boot and bonnet properly
5. Press the lock button of factory remote to lock the doors
6. The lights will flash and siren/horn chirp depending on the
setting of option #1
7. The N.C immobiliser will be on if connected
8. The windows will roll-up depending on the car itself and the
setting of option #9
9. The status LED flashes slowly to confirm the system is armed
* The doors will be protected after 5/25/40/60 sec. of system
arming depending on the setting of option #4
* if any door is not closed properly the siren/horn will chirp an
additional 3 times to warn within 5/25/40/60 sec. of system
arming and the doors will not be protected until they are
closed properly
* If the boot, bonnet is not closed properly then the siren/horn
will chirp additional 3 times when arming the system and the
boot or bonnet will not be protected until closed properly
2. Passive arming
If the passive arming is programmed to Mode-I or Mode-II, the
system will be armed in 30/180 sec. depending on the setting of
option #6. The operations are as follows:
1. With ignition off
2. The N.O immobiliser will be on if connected
3. AED will function in 20 or 30 sec. depending on the setting of
option #3
4. Close all the doors, boot and bonnet properly
5. 30/180 sec. later the system will be armed
6. The lights will flash and siren/horn will chirp depending on the
setting of option #1
7. The N.C immobiliser will be on if connected
8. The windows will roll-up depending on the setting of option
features #9
9. The status LED flashes slowly to confirm the system is armed
* Passive arming won’t function if the doors, boot or bonnet are
not closed properly
* Opening a door, boot or bonnet during the 30/180 sec.
countdown will interrupt the process of passive arming until it
is closed
3. Auto rearm
If the auto rearm is enabled (feature #7) the system will be
rearmed 30 sec. after disarming unless any of the doors, boot or
bonnet are opened
02. System disarm
The system can be disarmed as follows:
1. By pressing the unlock button of factory remote
2. Override the system
1. By pressing the unlock button of factory remote
The operation is as follows:
1. With system armed
2. Press the unlock button of factory remote
3. The lights will flash and siren/horn chirp depending on the
setting of option #1
4. The immobiliser will be on or off depending on the wiring and
the setting of AED (option feature #3)
5. The status LED will be off to confirm the system is disarmed
* If the system was triggered while away from the vehicle, the
siren will chirp an additional 4 times, the lights will flash an
additional 2 times and the LED will flash to indicate the
triggered zone as follows:
Triggered Zone
Led Indication
2nd sensor trigger
LED flashes one
Boot/Bonnet trigger
LED flashes 3 times
Door trigger
LED flashes 4 times
Ignition trigger
LED flashes 5 times
* The trigger memory will be erased once the ignition is
turned on
2. Override the system
If the factory remote becomes lost or malfunctions, the system
still can be disarmed by override as follows:
1. With the system alarmed
2. Turn the ignition on
3. After 2 sec., the LED starts to flash 10 times slowly
4. Press the valet switch once after the LED flashes a number of
times equal to the override code* (Default code: 1)
5. The system will be overridden and will enter disarm mode
* Wait for 3 minutes and then operate again after 3 times of
incorrect operation
03. Status LED indications
The status LED will indicate the system status as follows:
Led Indication
Slow Flash
Fast flash
Solid on
No Light
System Status
Armed
Auto rearm or Passive arming
Valet mode
Disarmed
04. Temporary sensor bypass
If necessary, the sensor can be bypassed temporarily as follows:
1. Turn the ignition off and then open the door
2. Press the valet switch until the lights flash once to confirm the
1st stage of sensors is bypassed
3. Press the valet switch until the lights flash twice to confirm the
sensors are bypassed entirely
* The function will deactivate after turning the ignition on
05. Valet mode
Valet mode is a convenient feature to use when handing the
remote to third person for valet parking or vehicle service and
the operation is as follows:
1. Turn the ignition on with the system disarmed
2. Within 10 sec. press the valet switch for 5 sec. and the LED will
turn on solid to confirm the system is in valet mode
To quit valet mode, follow the 2 methods as follows:
1. Operate the steps to enter the valet mode again, the LED will
turn off to confirm
2. The system will quit the valet mode automatically after 30
minutes of turning the ignition on
* In valet mode the system can’t enter the programming mode
and the AED won’t be activated
* Deactivate the AED before the system enters valet mode
otherwise the engine won’t be able to start in valet mode
06. System trigger and alarm
1. 1ST stage of sensor trigger
The siren will chirp 3 times and lights flash once when the 1st
stage of the sensor is triggered
2. 2nd stage of sensor trigger
1. The siren will sound for 1 cycle
2. The lights will flash for 1 cycle
3. The LED will flash
4. The 2nd stage of the sensor will be bypassed after 3 sequential
activations until the trigger is cleared
3. Boot or bonnet trigger (opened then closed)
1. The siren will sound for 1 cycle
2. The lights will flash for 1 cycle
3. The LED will flash
4. Boot or bonnet trigger (opened then not closed)
1. The siren will sound for 3 cycles
2. The lights will flash for 3 cycles
3. The LED will flash
4. After the 3 cycles, the boot/bonnet switch will be bypassed
until the boot or bonnet is closed properly
5. Door trigger (opened and then closed)
1. The siren will sound for 1 cycle
2. The lights will flash for 1 cycle
3. The LED will flash
6. Door trigger (opened and not closed)
1. The siren will sound for 3 cycles
2. The lights will flash for 3 cycles
3. The LED will flash
4. After the 3 cycles, the door trigger will be bypassed until the
doors are all cosed properly
7. Ignition trigger (on and then off)
1. The siren will sound for 1 cycle
2. The lights will flash for 1 cycle
3. The LED will flash
8. Ignition trigger (on and not off)
1. The siren will sound for 3 cycles
2. The lights will flash for 3 cycles
3. The LED will flash
4. After the 3 cycles, the ignition trigger will be bypassed until the
ignition is turned off
* 1 cycle = 30 or 60 sec. depending on the setting of option #9
07. Trigger and alarm clear
To clear the system during alarming do one of the following:
1. Press the lock button
2. Press the unlock button
3. Override
1. Press the lock button of factory remote:
When the system is triggered and alarmed, press the lock button
once, the siren and lights will deactivate and the system remains
armed
2. Press the unlock button of factory remote:
When the system is triggered and alarmed, press the unlock
button once, the siren and lights will deactivate. Then the lights
will flash additional 3 times, siren/horn will chirp additional 4
times and LED will flash to indicate the last triggered zone and
the system enters disarm mode
* The trigger memory will be erased after the ignition is turned
on
3. Override the system
Overriding the system will deactivate the siren and lights and the
system will enter disarm mode
08. Remote boot open
With system armed, press the factory remote to open the boot
(where applicable), the system won’t be triggered and alarmed
but will remain in arm mode. The boot will be protected after it
is closed again
B. System Programming
01. Setting the optional features
Follow the steps below to program the optional features:
1. With the system disarmed and ignition off
2. Open the door and turn the ignition on
3. Press the valet switch 3 times within 10 sec.
4. The siren will sound for 2 sec. to confirm the system is in
programming mode
* Reset all optional features back to the factory default:
Within 10 sec. press and hold the valet switch until the siren
sounds for 2 sec.
Programming example: To set option #5 to Mode-I
1. Press the valet switch 5 times within 10 sec. and the siren will
chip once after each press of the valet switch
2. After 2 sec., the siren will chirp 5 times to confirm that feature
#5 is selected for setting
3. Within 10 sec., press the valet switch until the siren chirp 2
times to confirm the feature has changed to Mode-I.(the
siren will respond with a different number of chirp for each
press of the valet switch)
4. After 2 sec., the siren will sound for 1 sec. to confirm the
optional feature is programmed
5. Within 10 sec. press the valet switch to select the next
feature for programming. If the valet switch is not pressed
again within 10 sec. the system will leave the programming
mode and the siren will sound for 2 sec. to confirm
* The system will leave the programming mode as follows:
1. Turn off the ignition or close the door during the
programming mode
2. If the valet switch is not pressed within 10 sec
02. Optional feature table
Item
Features
01
Arm & Disarm Confirmation
02
Installer only option
03
Auto Engine Disable(AED)
04
Installer only option
05
Passive Arming
06
Passive Arming Timer
07
Auto Rearm
08
Alarm Duration
09
Installer only option
10
Override Code
*Factory default = asterisk
9
1 chirp 9 2 chirp 9
Disable
Flash
Disable*
Mode-I
Disable*
Mode-I
30sec.
180sec.*
Disable*
Enable
30sec.*
60sec.
1 Flash*
3 chirp
Horn
Mode-II
Mode-II
-
9
4 chirp
Siren*
9
5 chirp
Siren+Flash
-
2 ~ 10 Flashes
-
C. Explanation of Optional Features
Option 1. Arm & disarm confirmation
This feature can make the indicator lights flash and/or car
horn/siren chirp when pressing the factory remote to arm or
disarm the system as follows:
2 chirp = Flash
Setting this feature to Flash will make the lights flashing once
when arming and twice when disarming
3 chirp = Horn
This feature will make the car horn honking once when arming
and twice when disarming
4 chirp = Siren
This feature will make the siren chirp once when arming and
twice when disarming
4 chirp = Siren+Flash
This feature will have the siren chirp once and lights flash once
when arming and twice when disarming
Option 3. Auto engine disable (AED)
This feature offers the car more security by disabling the starter
operation is as follows:
2 chirp = Mode-I
1. Turn the ignition off
2. The status LED starts to flash
3. 20 sec. later the AED will be active and the LED turns off to
confirm
4. Turning the ignition on or pressing the unlock button of the
factory remote within 20 sec. will cancel the countdown and
the LED will be off to confirm
5. To start the countdown again, simply turn the ignition on then
off and the LED will flash to confirm
6. Press the remote to arm the system during the 20 sec.
countdown to activate the AED immediately
*To deactivate the AED:
When disarming the system, the AED will remain on and the
only way to deactivate the AED is to operate the override
3 chirp = Mode-II
1. Turn the ignition off
2. The status LED starts to flash
3. 30 sec. later the AED will be on and LED turns off to confirm
4. Turning the ignition on or pressing the unlock button of factory
remote within the 30 sec. will cancel the countdown and the
LED will be off to confirm
5. To start the countdown again simply turn the ignition on then
off and the LED will flash to confirm
6. Press the remote to arm the system during the 30 sec.
countdown to activate the AED immediately
*To deactivate the AED:
There are 2 way to deactivate the AED in mode-II as follows:
1. Press the unlock button to disarm the system, the AED will be
deactivated at the same time
2. By override
* When AED is activated, the system can’t enter the following
modes:
• Code learning
• Programming of the optional features
• Hazard lights learning
• Valet mode
* The differences between Mode-I and Mode-II:
• In Mode-I, the system will enter AED mode 20 sec. after
turning the ignition off
• In Mode-II, the system will entry AED mode 30 sec. after
turning the ignition off
• In Mode-I, the AED won’t be deactivated after disarming the
system by pressing the unlock button of factory remote and
can only be deactivated by using the override
• In Mode-II, the AED will be deactivated when disarming the
system by pressing the unlock button of the factory remote.
Operating the override will also deactivate the AED
Option 5. Passive arming
When enabled, the system will arm as follows:
2 chirp = Mode-I
The operation is as follows:
1. Turn the ignition off
2. Close the doors, boot and bonnet properly
3. LED starts to flash fast and the system will arm in 30 or 180
sec.
4. The Auxiliary Output will activate as per the setting of feature
#9
* Opening the door, boot or bonnet will interrupt the
countdown until closed again
3 chirp = Mode-II
The operation of Mode-II is exactly same as Mode-I but the
Auxiliary Output won’t activate
Option 6. Passive arming timer
1 chirp = 30 sec.
The system will enter arm mode 30 sec. after closing the last
opened door, boot or bonnet with ignition off
2 chirp = 180 sec.
The system will enter arm mode 180 sec. after closing the last
opened door, boot or bonnet with ignition off
Option 7. Auto rearm
2 chirp = Enable
When enabled, the system will arm itself again 30 sec. after
disarming if none of the doors, boot or bonnet are opened
Option 8. Alarm duration
1 chirp = 30 sec.
The siren/horn will sound for 30 sec. each cycle when the
system is triggered
2 chirp = 60 sec.
The siren/ horn will sound for 60 sec. each cycle when the
system is triggered
Option 10. Override code
Follow the steps below to program the override code:
(For example: Programming 4 as the new override code)
1. Enter the programming mode
2. Within 10 sec. press the valet switch 10 times to select feature
#10, the siren will chip once for each press of the valet switch
3. After 2 sec., the siren will chirp 10 times to confirm the feature
#10 is selected for programming
4. Within 2 sec., press the valet switch once, the siren will chirp
2 times to indicate the current code is 2 (if the default code is
1)
5. Within 2 sec.press the valet switch once, the siren will chirp 3
times to indicate the current code is 3
6. Within 2 sec.press the valet switch once. the siren will chirp 4
times to indicate the current code is 4
7. Then 2 sec. later the siren will sound for 1 sec. to confirm the
code has been changed to 4
8. Within 10 sec. press the valet switch to select next feature for
programming or the system will leave the programming
mode and the siren will sound for 2 sec. to confirm
* The system will leave the programming mode as follows:
1. Turn the ignition off or close the door during programming
2. If the valet switch is not pressed within 2 sec or 10 sec.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement