user manual - sinclair air conditioners

user manual - sinclair air conditioners
USER'S MANUAL
MULTI COMBI SERIES
CASSETTE
MC- C24AI
User Notice
◆ When operating, the entire capacity of the cooperating indoor unit should be not larger than
150% of outdoor unit. Otherwise, it will cause the shortage of cooling (heating) capacity.
◆ A Breaker(or fuse) need to be installed in every indoor unit, and the capacity should
in according with indoor unit’s electrical parameter; all the indoor units are required to be
centralized controlled by a total Switch, this Switch can cut off the electric power supply in case of
emergency. The Breaker(or fuse) on each indoor units have the function of short circuit prevention
and abnormal overload avoiding, it should be connected in normal situation. The total switch
controlling the power supply of all the indoor units. Before clearing and maintenance job being
carried out to the indoor units, it is very important to turn off the total power supply switch.
◆ In order to turn on the units successfully, the main power switch should be opened 8 hours
before the operation.
◆ After receiving the turn off signal, every indoor unit will continue to work for 20-70sec to
make use of the rest cool air or the rest heat air in the heat exchanger, while preparing for the next
operation. And this is normal.
◆ When the selected operating mode of the indoor unit are clash with the operating mode of
the outdoor unit, the malfunction light will blink after 5s on the indoor unit or remote controller
showing that the operation clash, then the indoor unit will stop. At this time, change the operation
mode of the indoor unit to the one that would not clash with the outdoor operating mode to make
the operation normal. The cooling mode is not clash with the dry mode, while the fan mode is not
clash with any mode.
◆ The appliance shall not be installed in the laundry
◆ An all-pole disconnection switch having a contact separation of at least 3mm in all poles
should be connected in fixed wiring
◆ Information regarding transport/storage temperature (-25-55°C) is missing
◆ Main switch provided by end user: main switch handle should be black or gray, it can be
locked in “OFF” position with padlock
◆ The main disconnection device should be explained in user manual and the height should
be recommended at 0.6-1.7m. over current protection is required(EN 60947-3, EN 60947-2)
◆ The cooling range of the unit is the outdoor environment temp.-5~48°C DB, the heating
range of the unit( only for the heat pump type unit) is the outdoor environment temp. -15~27°C
WB.
This product must not be disposed together with the domestic waste. This product has to be
disposed at an authorized place for recycling of electrical and electronic appliances.
Thank you for your selecting of Sinclair air conditioner, please read this usage and
install instruction carefully and keep it well in order to use this unit correctly.
Wireless Remote Controller YT1F
Ⅱ Wireless Remote Controller YT1F
Notes:
① .Be sure that there are no obstructions between the receiver and the remote controller;
② .Do not drop or throw the remote controller;
③ .Do not let any liquid into the remote controller and expose the remote controller to direct sunlight or
any place where is very hot.
④ .T his is a general use remote controller. If press some button which is not available for the
corresponding function, the unit will keep the original running status.
1 Function of Press Buttons:
Fig.21
1) ON/OFF ( )
Press this button to turn on/off the unit. After that, the sleep function will be canceled but the preset time
is still remained.
2) MODE
Auto, Cool, Dry Fan, Heat modes can be selected circularly by pressing this button. Auto mode is the
default after power on. Under Auto mode, the temperature will not be displayed. Under Heat mode, the initial
value is 28℃ (82 ℉ ); Under other modes, the initial value is 25℃ (77 ℉ ).
3) SLEEP
Sleep On and Sleep Off can be selected by pressing this button. After powered on, the default is Sleep Off.
After the unit is turned off, the Sleep function is canceled. When the sleep function is set already, the symbol
will be displayed. And at this time, the time of timer can be adjusted. Under Fan and Auto modes, this
unction is not available.
18
Wireless Remote Controller YT1F
4) FAN
Auto, Low, Middle, or High fan speed can circularly selected by pressing this button. After powered on,
the default is Auto speed. Under Dehumidifying mode, only Low fan speed is available.
5) CLOCK
The clock can be set up by pressing this button, with the symbol
displayed and blinking. In such a
case, pressing + or - within 5 seconds can adjust the value. If the button is pressed down for more than 2
seconds, the value on ten’s place will increase by 1 in every 0.5 seconds. After that, repressing this button
and then symbol
stops blinking, which indicates the setting is made successfully. After powered on, the
default value is 12:00 with
displayed. Once the symbol
is displayed, the current time is the Clock value;
otherwise it is the Timer value.
6) LIGHT
Light On and Light Off can be set by pressing this button when the unit is at On or Off status. After
powered on, the default is Light On.
7) TURBO
In Cool or Heat mode, pressing this button can activate or deactivate this function. When this function
is on, its symbol will be displayed. Any change of either mode or fan speed will make this function canceled
automatically.
8) BLOW
BlOW On and BLOW Off can be set by pressing this button. In Cool and Dehumidifying modes, press
this button to activate this function and then “BLOW” will be displayed. After that, it can be canceled by
repressing this button. After powered on, the default is Blow Off. If the ON/OFF button is operated or the unit
is switched to the Cool or Dehumidifying mode, it will keep its original status. When the unit is turned off,
Only Blow Off is available. Under Auto, Fan or Heat mode, this function is unavailable.
9) -
The preset temperature can be decreased by pressing this button. If the button is pressed down for more
than 2 seconds, the temperature will be decreased quickly until it is released, with ℃ ( ℉ ) displayed al the
time. Under Auto mode, the temperature adjustment is unavailable.
10) +
The preset temperature can be increased by pressing this button. If the button is pressed down for more
than 2 seconds, the temperature will be increased quickly until it is released, with ℃ ( ℉ ) displayed all the
time. Under Auto mode, the temperature adjustment is unavailable. The setting range is 16-30 ℃ or 61-86 ℉
11) TEMP
It can be decided by pressing this button which temperature will be displayed, indoor set temperature, or
indoor ambient temperature. When the indoor unit is powered on, the indoor set temperature will be displayed,
, the indoor ambient temperature will be displayed. However, the indoor
while if the status is changed to
set temperature will be displayed again when the controller receives other remote controls signals. Without
setting this function, the default is the indoor set temperature.
12) SWING UP/DOWN ( )
The swing angle which circularly changes as below can be selected by pressing this button:
19
Wireless Remote Controller YT1F
This kind of remoter controller is universal. And the three swing statuses of
are the same
as that of
.
If the swing function is deactivated when the air guide louver is swing up and down, it will stop at the
current position.
indicates that the air guide louver swings up and down among all five positions.
13) AIR ( )
AIR ON or Air OFF can be selected by pressing this button.
14) TIMER ON
“ON” will be displayed and blink for 5 seconds by pressing this button, and soon adjust the time by
pressing + or - within 5 seconds. Each press will make the time increased or decreased by 1 minute. If
the button is pressed down for more than 2 seconds, the time will be changed quickly in such a way: firstly
the value on the one’s place is changed and then is the value on the ten’s place. Once Timer ON has been set
already, it can be canceled by repressing it. Before the setting, please adjust the CLOCK to the current actual
time.
15) TIMER OFF
TIME OFF can be activated by pressing this button, with “OFF” blinking. The method of setting is the
same as that for TIMER ON.
)
16) HEALTH (
This function can be activated or deactivated by pressing this button. After the unit is turned on, the
default is HEALTH ON.
17) I FEEL
This function can be activated by pressing this button and canceled by another press. When this function
is on, the I FEEL information will be sent out in 200ms after each operation on the controller and the remote
controller will send the temperature information to the main controller every 10 minutes.
2 Guide for General Operation
a. After powered on, press ON/OFF and then the unit will start to run. (Note: when powered off, the
guide louver of the main unit will close automatically).
b. Press MODE to select the desired running mode.
c. Press + or - to set the desired temperature (it is unnecessary to set the temperature under the AUTO
mode.)
d. Press FAN to set the fan speed, AUTO, LOW, MID, or HIGH.
e. Press
to select the swing angle.
3 Guide for Optional Operation
a. About BLOW
This function indicates that moisture in the evaporator of the indoor unit will be dried after the unit is
stopped to avoid mould.
① .BLOW ON: When press the ON/OFF button to turn off the unit, the indoor fan will continue running
for about another 10 minutes at the low speed. In this case, the indoor fan can be stopped directly by pressing
the button BLOW.
20
Wireless Remote Controller YT1F
② .BLOW OFF: When press the ON/OFF button to turn off the unit, the whole unit will be stopped
completely.
b. About AFTERHEAT BLOW
Under the Heat mode or Auto Heat mode, if the unit is turned off, the compressor and outdoor fan will
stop running immediately and the upper and lower guide board will rotate to the horizontal position, while the
indoor fan will still run at the low fan speed. Then, 10 seconds later, the unit will stop completely.
c. About AUTO RUN
When AUTO RUN is selected, the setting temperature will not be displayed on the LCD and the unit will
choose the suitable running mode automatically in accordance with the room temperature.
d. About TURBO
If this function is activated, the unit will run at super-high fan speed to cool or heat quickly so that the
ambient temperature will approaches the preset temperature as soon as possible.
21
Wired Controller XK19
Ⅰ Wired Controller XK19
1 Wired Controller XK19
It is optional for the cassette type, wall-mounted, and floor ceiling indoor units.
1.1 Outside View of the Wired Controller
Fig.1 Outside View of the Wired Controller
1.2 LCD of the Wired Controller
Fig.2 LCD of the Wired Controller
1
Wired Controller XK19
1.3 Introduction to the Symbols on LCD
Table 1
No.
Symbols
Description
1
Swing function.
2
Sleep function (3 types: sleep 1,sleep2 and sleep 3).
3
Running modes of the indoor unit (Cooling, Dry, Fan and Heating).
4
Defrosting function for the outdoor unit.
5
Gate-control function (this function is yet unavailable for this unit).
6
Lock function.
7
High, middle, low or auto fan speed of the indoor unit.
8
SHIELD
Shield functions (buttons, temperature, On/Off, Mode or Save is shielded or
Save is shielded by the remote monitor.
9
TURBO
Turbo function.
10
MEMORY
Memory function (The indoor unit resumes the original setting state after
power failure and then power recovery).
11
MASTER
Master wired controller (this function is yet unavailable for this unit).
It blinks under on state of the unit without operation of any button.
12
13
SAVE
Energy-saving function.
Ambient/preset temperature value.
14
15
E-HEATER
16
BLOW
Electric auxiliary heating function.
Blow function.
Timing value.
17
18
QUITE
Quiet function (two types: quiet and auto quiet).
19
SET
It will be displayed under the debugging mode.
2 Buttons
2.1 Buttons on the Wired Controller
Fig. 3 Buttons on the Wired Controller
2
Wired Controller XK19
2.2 Function of the Buttons
Table 2
No.
Name
1
Enter/cancel
2
▲
6
▼
3
Fan
4
Mode
5
Function
Function
① Function selection and cancellation.
② Press it for 5s to examine the outdoor ambient temperature.
① Running temperature setting of the indoor unit, range:16 ~ 30℃ .
② Timer setting, range:0.5-24 hr.
③ Switchover between quiet/auto quiet or among sleep1/sleep2/sleep 3.
Setting of the high/middle/low/auto fan speed.
Setting of the Cooling/Heating/Fan/Dry mode of the indoor unit.
Switchover among the functions of Swing/Sleep/Turbo/Save/E-heater/Blow /
Quiet etc.
7
Timer
Timer setting.
8
On/Off
Turn on/off the indoor unit.
4+2
▲+Mode
3 +6
Fan+▼
2 +6
▲+▼
Press them for 5s under off state of the unit to enter/cancel the Memory function
(If memory is set, indoor unit after power failure and then power recovery will
resume the original setting state. If not, the indoor unit is defaulted to be off after
power recovery. Memory off is default before delivery.).
By pressing them at the same time under off state of the unit, will be displayed
will be displayed on
on the wired controller for the cooling only unit, while
the wired controller for the cooling and heating unit.
Upon startup of the unit without malfunction or under off state of the unit,press
them at the same time for 5s to enter the lock state, in which case, any other
buttons won’t respond the press. Repress them for 5s to quit this state.
3 Operation Instructions
3.1 On/Off
Press On/Off to turn on the unit and turn it off by another press.
Note: The state shown in Fig.4 indicates the “Off” state of the unit after power on. The state shown in
Fig.5 indicates the “On” state of the unit after power on.
Fig. 4 “Off” State
Fig. 5 “On” State
3.2 Mode Setting
Under the “On” state of the unit, press Mode to switch the operation modes as the following sequence:
Cooling-Dry-Fan-Heating.
3
Wired Controller XK19
3.3 Temperature Setting
Press ▲or ▼ to increase/decrease the preset temperature. If press either of them continuously, the
temperature will be increased or decreased by 1℃ every 0.5s,as shown in Fig.6.
In the Cooling, Dry or Heating mode, the temperature setting range is 16℃~ 30℃ .
In the Fan mode, the setting temperature is fixed at 26℃ .
In the Auto mode, the setting temperature is unadjustable.
Fig.6
3.4 Fan Setting
Under the “On”/”Off” state of the unit, press Fan and then fan speed of the indoor unit will change
circularly as shown in Fig.7.
Auto
Low
Middle
High
Fig.7
3.5 Timer Setting
Under the “On”/”Off” state of the unit, press Timer to set timer off/on.
Timer on setting: press Timer, and then LCD will display “xx.x hour”, with “hour” blinking. In this case,
press ▲or ▼ to adjust the timing value. Then press Enter/cancel to confirm the setting.
Timer off setting: press Timer, if LCD won’t display xx.x hour, and then it means the timer setting is
canceled.
4
Wired Controller XK19
Timer off setting under the “On” state of the unit is shown as Fig.8.
Fig. 8 Timer off Setting under the “On” State of the Unit
Timer range: 0.5-24hr. Every press of ▲or ▼ will make the set time increased or decreased by 0.5hr. If
either of them is pressed continuously, the set time will increase/ decrease by 0.5hr every 0.5s.
3.6 Swing Setting
Swing On: Press Function under on state of the unit to activate the swing function. In this case,
blink. After that, press Enter/cancel to make a confirmation.
Swing Off: When the Swing function is on, press Function to enter the Swing setting interface, with
blinking. After that, press Enter/cancel to cancel this function.
Swing setting is shown as Fig.9.
5
will
Wired Controller XK19
Fig. 9 Swing Setting
Note:
① .Sleep, Save, Turbo, Blow or Quiet setting is the same as the Swing setting.
② .After the setting has been done, it has to press the key “Enter/cancel” to back to the setting status or
quit automatically five seconds later.
3.7 Sleep Setting
Sleep on: Press Function under on state of the unit till the unit enters the Sleep setting interface. Then
press ▲or ▼ to switch among Sleep 1, Sleep 2 and Sleep 3. After that, press Enter/cancel to confirm the
setting.
Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting interface. After
that, press Enter/cancel to can this function.
Sleep setting is shown as Fig.10.
6
Wired Controller XK19
Fig. 10 Sleep Setting
Sleep off is default after power failure and then power recovery, and the sleep functions is unavailable
under the fan mode.
There are three Sleep modes: Sleep 1, Sleep 2 and Sleep 3.
a. Sleep 1
In the Cooling or Dry mode, the temperature will increase by 1℃ after the unit runs under Sleep 1 for 1hr
and 1℃ after another 1hr.After that, the unit will run at this temperature.
In the Heating mode, the temperature will decrease by 1℃ after the unit runs under Sleep 1 for 1hr and
1℃ after another 1hr. After that, the unit will run at this temperature.
b. Sleep 2
In the Cooling mode, the temperature may be set between 16 ℃ -23 ℃ , 24 ℃ - 27 ℃ or 28 ℃ - 29 ℃
or at 30 ℃ , and their Sleep curves are shown in Fig.11 (Note: The curve is only for reference, the actual
temperature is subject to the time point.).
For example: The temperature in the Cooling mode is set at 25 ℃ . Under the mode of Sleep 2, the
temperature will increase by 1℃ every 1hr. After it increases by 2℃ in total, it will keep at 27℃ . 7 hours
later, it will decrease by1℃ , i.e. 26℃ .After that, the unit will keep running at 26℃ .
7
Wired Controller XK19
(
T
e
m
p
/
)
℃
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
1
2
3
4
5
6
7
8
9
10
11
12
Time/(Hr)
Fig.11 Sleep Curve of Sleep 2 in Cooling Mode
In the Heating mode, the temperature may be set at 16℃ or between 17℃ - 20℃ , 21℃ -27℃ or 28℃ 30℃ and their Sleep curves are shown in Fig.12:
(
T
e
m
p
/
)
℃
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
1
2
3
4
5
6
7
8
9
10
11
12
T i m e /(H r )
Fig.12 Sleep Curve of Sleep 2 in Heating Mode
8
Wired Controller XK19
For example, the temperature in the Heating mode is set at 22 ℃ .Under the mode of Sleep2, the
temperature will decrease by 1 ℃ every 1hr. After it decreases by 2 ℃ in total, i.e. 20 ℃ ,the unit will keep
running at 20℃ .
c. Sleep 3
Sleep curve setting under Sleep 3(DIY mode)
d. Under the mode of Sleep 3, press Timer to enter the Sleep setting. In this case, “1 HOUR” is displayed
where the timing value once is displayed and the corresponding temperature with the last Sleep curve setting
is displayed where the ambient/preset temperature once in displayed.
e. Press ▲or ▼ to change the corresponding temperature setting.
f. Press Timer, time will automatically increase by 1hr, and the corresponding temperature with the last
Sleep curve setting is displayed where the ambient/preset temperature once is displayed.
g. Repeat step 2 and step 3 till 8 HOUR Sleep setting is finished.
h. Press Enter/cancel to confirm the setting.
Sleep curve setting under Sleep 3 is as shown in Fig.13.
Fig. 13 Sleep Curve Setting under Sleep 3
Notes:
① .During the above setting, if Function is pressed down or there is not any operation within 5s, sleep
curve setting will be canceled.
② .26℃ is the default Sleep curve temperature before delivery. The wired controller will automatically
memorize the Sleep curve after the setting.
3.8 Turbo Setting
Turbo function: The unit at the high fan speed can realize quick cooling or heating so that the room
temperature can quickly approach the setting value.
In the Cooling or Heating mode, press Function till the unit enters the Turbo setting interface and then
press Enter/Cancel to confirm the setting.
9
Wired Controller XK19
When the Turbo function is activated, press Function to enter the Turbo setting interface and then press
Enter/Cancel to cancel this function.
Turbo function setting is as shown in Fig.14.
Fig.14 Turbo Setting
Notes:
① .When the Turbo function is activated, if the difference between the room temperature and set
temperature is at or below 2 ℃ (detected in successive 1 min.), the Turbo function will be automatically
deactivated.
② .Turbo function is unavailable in the Dry and Fan mode. And the Turbo function is off after power
failure and then power recovery. If Quiet function is on, Turbo function will be canceled subsequently.
3.9 Save Setting
Save: Energy saving which will result the air conditioner runs in smaller temperature range is realized by
setting lower limited value in the Cooling or Dry mode and upper limited value in the Heating mode.
Save Setting for Cooling:
Under the “On” state and in the Cooling or Dry mode of the unit, press Function to enter the Save setting
interface and then press ▲or ▼ to adjust the lower limited value in the Cooling mode. After that, press Enter/
Cancel to activate the Save function. The initial lower limited value in the Cooling mode is 26℃ .
When the Save function is activated, press Function to enter the Save setting interface and then press
Enter/cancel to cancel this function.
The Save setting for cooling is shown in the Fig.15
10
Wired Controller XK19
Fig. 15 Saving Setting for Cooling
Save Setting for Heating:
Under on state or in the Heating mode of the unit, press Function to enter the Save setting interface and
then press ▲or ▼ to adjust upper limited value in the Heating mode. After that, press Enter/Cancel to activate
the Save function for heating. The upper initial limited value in the Heating mode is 20℃ .
After the Saving function is activated, press Function to enter the Save setting interface and then press
Enter/Cancel to cancel this function.
Save setting for heating is as shown in Fig. 16
11
Wired Controller XK19
Fig.16 Save Setting for Heating
Notes:
① .If press Function on the Save setting interface or if there is not any operation for 5s after last button
press, the Save setting will be canceled automatically by the system, with memorizing the present setting data.
② .When power is on after the power failure, the Save function will be memorized.
3.10 E-heater Setting
E-heater (auxiliary electric heating function): In the Heating mode, E-heater is allowed to be turned on for
improvement of efficiency.
Once the wired controller or the remote controller enters the Heating mode, this function will be turned on
automatically.
Press Function in the Heating mode to enter the E-heater setting interface and then press Enter/cancel to
cancel this function.
Press Function to enter the E-heater setting interface, if the E-heater function is not activated, and then
press Enter/Cancel to turn it on.
The setting of this function is shown as Fig.17 below:
12
Wired Controller XK19
Fig.17 E-heater Setting
3.11 Blow Setting
Blow function: After the unit is turned off, the water in evaporator of indoor unit will be automatically
evaporated to avoid mildew.
In the Cooling or Dry mode, press Function till the unit enters the Blow setting interface and then press
Enter/Cancel to active this function.
When the Blow function is activated, press Function to the Blow setting interface and then press Enter/
Cancel to cancel this function.
Blow function setting is as shown in Fig.18
13
Wired Controller XK19
Fig.18 Blow Setting
Notes:
① .When the Blow function is activated, if turning off the unit by pressing On/Off or by the remote
controller, the indoor fan will run at the low fan speed for 10 min, with “BLOW” displayed on the LCD.
While, if the Blow function is deactivated, the indoor fan will be turned off directly.
② .Blow function is unavailable in the Fan or Heating mode.
3.12 Quiet Setting
Quiet function consists of two kinds: quiet and auto quiet.
Press Function till the unit enters the Quite setting interface, with “Quiet” or “Auto” blinking. In this case,
press ▲or ▼ to switch between Quiet and Auto and then press Enter/cancel to make a confirmation.
When the Quiet function is activated, press Function till the unit enters the Quite setting interface, with
“Quite” or “Auto” blinking. Then press Enter/cancel to cancel this function.
Quiet function setting is as shown in Fig.3.16:
14
Wired Controller XK19
Fig.19 Quiet Setting
Notes:
① .When the Quite function is activated, the fan speed is low and un-adjustable.
② .When the Auto Quite function is activated, the unit will run according to the difference between the
room temperature and the setting temperature. In this case, the fan speed is adjustable.
Difference between the room temperature and the setting temperature: the fan speed will keep its current
state if the temperature difference ≥ 4 ℃ ; the fan speed will reduce one grade if 2 ℃ ≤ the temperature
difference ≤ 3℃ ; the fan speed will be at min. grade if the temperature difference ≤ 1℃ .
③ .When the Auto Quiet function is on, the fan speed can not be raised but reduced. If the high fan speed
is manually adjusted, the function will quit automatically.
④ .There is not Auto Quiet function in the Fan or Dry mode. Quiet off is default after power failure and
then power recovery.
3.13 Other Functions
a. Lock
Upon startup of the unit without malfunction or under the “Off” state of the unit, press ▲ and ▼ at the
same time for 5s till the wired controller enters the Lock function. In this case, LCD displays . After that,
repress these two buttons at the same time for 5s to quit this function.
Under the Lock state, any other button press won’t get any response.
b. Memory
Memory switchover: Under the “Off” state of the unit, press Mode and ▲ at the same time for 5s to
switch memory states between memory on and memory off. When this function is activated, Memory will be
displayed. If this function is not set, the unit will be under the “Off” state after power failure and then power
recovery.
15
Wired Controller XK19
Memory recovery: If this function has been set for the wired controller, the wired controller after power
failure will resume its original running state upon power recovery. Memory contents: On/Off, Mode, set
temperature, set fan speed, Save function and Lock function.
c. Enquiry of the Outdoor Ambient Temperature
Under the “On” or “Off” state of the unit, press Enter/Cancel for 5s, and the outdoor ambient temperature
will be displayed after a sound of click. This enquiry state will quit by pressing Function or On/Off or during
the temperature adjustment. If there is not any operation for 10s, it will also quit automatically.
4 Errors
If there is an error occurring during the operation of the system, the error code will be displayed on the
LCD, as show in Fig.20. If multi errors occur at the same time, their codes will be displayed circularly.
Note: In event of any error, please turn off the unit and contact the professionally skilled personnel.
Fig.20
16
Wired Controller XK19
Table 3 Meaning of Each Error
Error Code
Error
High pressure protection
E1
Low pressure protection
E3
Discharge protection
E4
Over-current protection
P5
Communication error
E6
Indoor water overflow protection
E9
Mode conflict
E7
Anti-freezing protection
E2
Defrosting or oil returning for heating
H1
Indoor ambient temperature sensor open/short circuit
F1
Evaporator temperature sensor open/short circuit
F2
Indoor unit (liquid valve) refrigerant pipe inlet temperature sensor error
b5
Indoor unit (gas valve) refrigerant pipe outlet temperature sensor error
b7
Condenser coil inlet temperature sensor open/short circuit
A5
Condenser coil midway temperature sensor error
F4
Condenser coil outlet temperature senor open/short circuit
A7
Discharge air temperature sensor error
F5
Outdoor ambient temperature sensor error
F3
Module temperature sensor error
oE
Outdoor unit overall error
oE
17
Contents
Safety Information............................................................................................ 1
Install Of The Cassette Type Indoor Unit......................................................... 2
Constitutes and Names of Parts of Cassette Type Indoor Unit ..................... 11
Working Temperature Range.......................................................................... 12
Operation Method When Meeting An Emergency ...................................... 13
Malfunction Debarring.................................................................................... 14
Maintenance Method...................................................................................... 16
Safety Information
Safety Information
Please read this manual carefully before use this unit, and operate it correctly according to the guide in
this manual.
Please take specially note to the meaning of these two marks:
Warning!: This mark means that it may cause casualty or badly heart if the operation is incorrect.
Note!: This mark means that it may cause casualty or property loss if the operation is incorrect.
Warning:
◆ Do not adopt fuse with unsuitable capacity or adopt iron thread instead of fuse, otherwise malfunction
or fire may happened.
◆ Cut down the main power switch immediately if malfunction (such as smell the burning odor etc.)
happened.
◆ Maintain ventilation to prevent oxygen leakage in room.
◆ Don’t insert finger or stick like things into discharge vent or outlet grill.
◆ Please make sure that the unit is installed in the place that can bear the weight of it adequately. If the
place is not strong enough, the air conditioner may drop and cause casualty event.
◆ Don’t spray or smear any oil paint or insecticide on the surface of unit, otherwise, fire may be leaded.
◆ Do not refit the conditioner. Please contact the agency or prefect ional personnel to repair or move the
conditioner.
An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be
connected in fixed wiring.
Note!:
◆ Please check and make sure that the cord, drainage pipe and tubes are connected in the correct way to
prevent leakage of water, refrigerant, electric shock or fire.
◆ The main power must connectable to the earth in order to assure the conditioner earthing effectively
and to prevent electric shock. Please don’t connect the earthing line with the gas pipe, water pipe, lightening
rod or the connecting line of telephone.
◆ The air conditioner should be turned off at least after 5 mins’ operation; otherwise it would affect the
duration of the unit.
◆ Don’t let the children operate the air conditioner.
◆ Please don’t operate the unit by wet hand.
◆ Please turn off the main power of the unit before cleaning the conditioner or change the filter.
◆ Please cut off the main power if the conditioner will be used for a long time.
1
Install Of The Cassette Type Indoor Unit
Install Of The Cassette Type Indoor Unit
★ Schematic diagram of installation spaces
H
>20
Wall
surface
Wall
surface
Wall
surface
≥1500
≥1800
≥1500
Model
MC-C24AI
unit:mm
H
260
Ground
surface
Fig.1
★ Select install location of the indoor unit
1. Obstruct should put away from the intake or outlet vent of the indoor unit so that the airflow can be
blown though all the room.
2. Make sure that the installation had accord with the requirement of the schematic diagram of installation
spaces.
3. Select the place where can stand 4 times of the weight of the indoor unit and would not increase the
operating noise and oscillate.
4. The horizontally of the installation place should be guaranteed.
5. Select the place where easy drain condensated coagulated water, and easy connect with outdoor unit.
6. Make sure that there are enough space for care and maintenance. Make sure that the weight between
the indoor unit and ground is above 1800mm.
7. When installing the steeve bolt, check if the install place can stand the weight 4 times of the unit’s. If
not, reinforce before installation. (Refer to the install cardboard and find where should be reinforced)
Note!
There will be lots of lampblack and dust stick on the acentric, heat exchanger and water pump in dining
room and kitchen, which would reduce the capacity of heat exchanger, lead water leakage and abnormal
operation of the water pump. The following treatment should be taken under this circumstance:
1. Ensure that the smoke trap above cooker has enough capacity to obviate lampblack to prevent the
indraft of the lampblack by the air conditioner.
2. Keep the air conditioner far from the kitchen so that the lampblack would not be indraft by the air
conditioner.
★ Important notice:
◆ To guarantee the good performance, the unit must be installed by professional personnel according
with this instruction.
◆ Please contact the local special nominated repair department before installation. Any malfunction
2
caused by the unit that is installed by the department that is not special nominated by Nepa spol.s.ro. would not deal
with on time by the inconvenience of the business contact.
780( Gaps between hoisting screw rods)
840( Indoor unit)
890*(Ceiling opening)
950( Decorated surface boards )
★ Dimension of ceiling opening and location of the hoisting screw (M10)
Refrigerant pipe
Hoisting screw (X4)
680(Gaps between hoisting screw rods)
840( Indoor unit )
MC-C24AI
890(Ceiling opening )
950(Decorated surface boards )
A
Fig.2 Install dimension of mode
◆ The drilling of holes in the ceiling must be done by the professional personnel.
Ceiling
(160)
Installation stands for main body of the unit
Fig.3
Above 20
Notes: The dimension for the ceiling openings with * marks can be as large as 910mm. But the
overlapping sections of the ceiling and the decorated surface boards should be maintained at no less than
20mm.
★ Main body of hoisting air conditioner
1 The primary step for install the indoor unit.
◆ When attach the hoisting stand on hoisting screw, do use nut and gasket individually at the upper and
lower of the hoisting stand to fix it. The use of gasket anchor board can prevent gasket break off.
2 Use install cardboard
◆ Please refer to the install cardboard about the dimension of ceiling opening.
◆ The central mark of the ceiling opening is marked on the install cardboard.
3
◆ Install the install cardboard on the unit by bolt (3 piece), and fix the angle of the drainage pipe at the
outlet vent by bolt.
3 Adjust the unit to the suitable install place. (Refer to the fig.3)
4 Check if the unit is horizontal.
◆ Inner drainage pump and bobber switch are included in the indoor unit, check if 4 angle of every unit
are horizontal by water lever. (If the unit is slant toward the opposite of the coagulate water flow, there may be
malfunction of the bobber switch and lead water drop.)
5 Backout the gasket anchor board used to prevent gasket break off and tighten the nut on it.
6 Backout the install cardboard.
Fig.4
Note!
● Please do tighten the nuts and bolts to prevent air conditioner break off.
★ Connection of the refrigerant pipe
◆ When connect the pipe to the unit or backout it from the unit, please do use both spanner and torque
wrench. as shown in fig.5.
◆ When connect, smear both inside and outside of the flare nut with freeze motor oil, screw it by hand
and then tighten it with spanner.
◆ Refer to form 1 to check if the wrench had been tightened (too tight would mangle the nut and lead
leakage).
◆ Examine the connection pipe to see if it had gas leakage, then take the treatment of heat insulation, as
shown in the fig.5.
◆ Only use median sponge to entwine the wiring interface of the gas pipe and heat preservation sheath of
the gas collection tube.
4
Smear freeze motoroil
here
Median sponge (attachment)
(entwine the wiring interface
with seal mat)
Thread fasten(x4)
Torque wrench
Heat preservation
sheath of liquid inlet
tube (attachment) (for
liquid tube)
Spanner
Flare nut
Wiring interface
Gas collection tube
Liquid inlet tube
Heat preservation
sheath of gas collection
tube (attachment)(for
gas tube)
Fig.5
Form 1: The tightening torque needed for tightening nut
Diameter(Inch)
Surface thickness(mm)
Tightening torque (N·m)
φ1/4’’
≥ 0.5
15-30 (N·m)
φ3/8’’
≥ 0.71
30-40 (N·m)
φ1/2’’
≥1
45-50 (N··m)
φ5/8’’
≥1
60-65 (N·m)
φ3/4’’
≥1
70-75 (N··m)
★ Drainage hose
1. Install the drain hose
◆ The diameter of the drain hose should be equal or bigger than the connection pipe’s. ( The diameter of
polythene pipe: Outer diameter 25mm Surface thickness ≥ 1.5mm)
◆ Drain hose should be short and drooping gradient should at less 1/100 to prevent the formation of air
bubble.
◆ If drain hose cannot has enough drooping gradient, drain raising pipe should be added.
◆ To prevent bent of the drain hose, the distance between hoisting stand should is 1 to 1.5m.
Fig.6
◆ Use the drain hose and clamp attached. Insert the drain hose to the drain vent, and then
tighten the clamp.
◆ Entwine the big sponge on the clamp of drain hose to insulate heat.
◆ Heat insulation should be done to indoor drain hose.
5
Sponge(attachment)
Clamp
Sponge (gray)
Clamp(attachment)
Drain hose
Below 4mm
Fig.7
Drain stepup pipe note
◆ The install height of the drain raising pipe should less than 280mm.
◆ The drain raising pipe should form a right angle with the unit, and distance to unit should not beyond
300mm.
Fig.8
Instruction
◆ The slant gradient of the attached drain hose should be within 75mm so that the drain hole doesn’t has
to endure the unnecessary outside force.
Fig.9
◆ Please install the drain hose according to the following process if several drain hoses join together.
Fig.10
2 Check the smoothness of drain after installation.
◆ Check the drain state by immitting 600cc water slowly from the outlet vent or test hole.
◆ Check the drain in the state of refrigerating after installation of the electric circuit.
6
Fig.11
★ Electrical wiring
Note:The power of the entire indoor unit must be connected in outdoor unit.
◆ About the electrical wiring, please see the circuit diagram attached with the unit.
◆ All the installation of electrical wiring must be done by professional personnel.
◆ Please do take the earthing treatment.
Wiring method of connection unit and controller
◆ Connection wiring (communication):
① Open electric box cover(1), drag the wiring (communication)from the rubber plug A, and impact them
well individually by impact fastener.
② Wiring according to the indoor side circuit diagram.
◆ Fix the impact fastener after connection.
◆ Entwine the small sponge on the electric wire ( do entwine it to prevent condensation)
◆ Impact tightly by impact fastener after connection and then fit on the electric box (1) and (2).
◆ Connect the wiring (communication) through the piping hole of the chassis and the bottom of the
appliance upward, then connect the brown wire to the Terminal board “3”;black wire(the communication wire)
to the Terminal board“2”;blue wire to the Terminal board“N(1)”.and connect the earthing wire to the screw
terminal on the electric box.
7
Fig.12
★ Install the panel
1. Set the panel to the indoor unit body by matching the position of the swing flap motor of the panel to
the piping position of the panel to the piping position of the indoor unit as shown by fig.13.
2. Install the panel
① Install the panel on the indoor unit temporarily. When install, hang the latch on the hook that is located
on the opposite side of the swing flap on the panel of the indoor unit. (2 positions)
② Hang the remaining 2 latches to the hooks on the sides of the indoor unit.(Be careful not to let the
swing motor lead wire get caught in the sealing material.)
③ Screw the 4 hexagon head screws under the latches in about 15mm. (The panel would rise)
④ Adjust the panel by turning it toward the direction pointed by the arrow as shown in fig.13, so that the
adjust board connect the ceiling well.
⑤ Tighten the screws until the thickness of the sealing material between panel and indoor unit reduced to
5-8mm.
8
Fig.13
Notes:
1. Improper screwing of the screws may cause the troubles shown in fig.14.
Air leak
Air leak from ceiling
Water condensatation, water drop
Fig.14
2. If gap still exist between ceiling and decoration panel after tightening the screws, readjust the height of
the indoor unit. (As shown in fig.15)
If the raising lever and drain hose are
not affect, can adjust the height of
indoor unit by the hole on the corner
of panel.
Gaps are not allowed
Fig.15
9
※ After fixing, be sure no gap left between the ceiling and the panel.
3. Wiring of the decoration panel (Fig.16)
Connect the joints for swing flap motor lead wire (at 2 places) installed on the panel.
At body
At body
At pane
Fig.16
10
At pane
Constitutes and Names of Parts of Cassette Type Indoor Unit
MC-C24AI
11
Working Temperature Range
Working Temperature Range
Indoor side state
12
Outdoor side stae
Dry bulb
temp. ℃
Wet bulb
temp. ℃
Dry bulb
temp. ℃
Wet bulb
temp. ℃
Rated Cooling
27
19
35
24
Max. cooling
32
23
48
26
Min. cooling
21
15
18
—
Rated Heating
20
15
7
6
Max. heating
27
—
24
18
Min. heating
20
15
- 15
- 16
Operation Method When Meeting An Emergency
When wireless remote controller is lost or damaged, the following method could be adopted to control
cassette type indoor unit:
◆ When the unit is turned off, press AUTO button on corner outer cover Ⅱ , then the unit begin operate
in cooling with the fan run in high speed. The temp. will be set to 26 ℃ automatically.
◆ When the unit is turned off, press TEST button on the corner outer cover Ⅱ , then the unit begin
running in heating and the fan is running in high speed. The temp. will be set to 20 ℃ automatically.
◆ When the unit is running, press AUTO button on corner outer cover Ⅱ , then the unit stops running;
under the running state of heating, press TEST button on corner outer cover Ⅱ , then the unit stops running.
Note!
Prevent using the operating method for meeting an emergency when the wireless remote controller could
be used in normal. There are 3 lights on corner outer cover Ⅱ , red for power, green for running, and yellow
for timer.
Fig.17
13
Malfunction Debarring
Warning!
◆ Cut down the main power switch immediately if malfunction (such as smell the burning odor etc.)
happened, and then contact service center. If the abnormal state is maintained, the unit may be damaged or
electric shock or fire may be happened.
◆ Do not refit the conditioner. Please contact service center to repair or move the conditioner.
★ Check the following items before contacting maintenance center
Phenomena
Air conditioner doesn’t
run at all
Reason
Remedial Measures
Blow of fuse or breaker
Change fuse or close breaker
Power cut
Restart when there is power supply
Don’t connect with power
Connect power well
Low batteries of wireless remote
controller
Wireless remote controller exceed
remote control area
Air conditioner runs but
Blockage in inlet or outlet vent of
stops immediately
indoor or outdoor unit
Blockage in inlet or outlet vent of
indoor or outdoor unit
Improper of temp. setting
Low setting of fan speed
Incorrect of wind direction
Abnormal cooling or
heating
Door or window opened
Direct sun burn
Change new batteries
Signal could be received within 8m
Clean out blockage
Clean out blockage
Adjust settings in wireless remote
controller
Adjust settings in wireless remote
controller
Adjust settings in wireless remote
controller
Close
Hang curtain or jalousie before
windows
Too many people in room
Too many heater in room
Filter blocked by dirt
14
Clean filter
★ Instruction
If problem still cannot found out after above checking, please contact service center and instruct
phenomena and model.
★ The following circumstance are not malfunction
“Malfunction”
Air conditioner doesn’t
Reason
Start up unit immediately after turned
The overload protects switch makes it
off
run after 3 minutes delay.
run
When opening power
Mist is blown from air
conditioner
Noise is heard from air
conditioner
When cooling
Run for about 1 minute without other
actions
The high humidity air in room is
cooled rapidly
Slight click sound heard once begin
Sound of initialization for electric
running
expand valve
Hissing sound heard continuously
The sound for gas refrigerant flowing
when cooling
in the unit
Hissing sound heard when staring or
The sound for gas refrigerant stops
stopping
flow
Slight hissing sound heard when
running or after running
Creak sound heard when running or
after running
Dust be blown for air
Started up after long time’s doesn’t
conditioner
runs
Sound for running of drainage system
The grating sound caused by expands
of panel and other parts for the
change of temperature
Dust in indoor unit be blown out
This is because when air conditioning,
Odor gives out from air
conditioner
When running
odors or cigarette smoke from the
room that was sucked in is discharged
again.
★ After-sales Service
When having quality or other problems when purchasing air conditioner, please contact the local service
center.
15
Maintenance Method
When air conditioner won’t be used for a long time, please cut off the main power supply of air
conditioner.
Warning!
◆ Do turn off the unit and cut off the main power supply when cleaning the air conditioner, otherwise
electric shock or harm may happen.
◆ It is forbidden to wash air conditioner by water rinsing, otherwise electric shock may happen.
★ Cleaning air filter
When the usage environment has lots of dust, air filter should be cleaned more frequently (about once 6
months).
1. Open air inlet grille
Pull the 2 handle on air inlet grille at the same time with the direction showed by arrow in fig. 18, pull
down slowly. (Reverse when closing)
2. Disassembly air filter
As shown in fig. 19, pull the handle behind air inlet grille, raise it and disassembly. Then discharge the 3
purifier fixed on filter.
purifier
Fig. 18
Fig. 19
3. Clean
Adopts cleaner or water to wash filter; if the filter is too dirty ( like oil stain on it ), adopts warm water (
lower than 45℃ ) with neutral scourer to clean it, then dry it in the shade.
Note !
Do not clean the filter by hot water whose temp. is higher than 45℃ to prevent fade or deformation.
Do not burn it on fire or the filter would catches fire or deformation.
4. Install air filter
Fix the 3 purifiers on filter, install filter on the several bulges on top of air inlet grille, pull the handle
behind air inlet grille toward inside to fix filter. As shown in fig. 20.
5. Close air inlet grille (Refer to the 1st step)
Maintenance Method
16
Fig. 20
Fig. 21
★ Clean air inlet grille
1. Open air inlet grille (the same with the 1st step of Clean Air Filter)
2. Take out air filter (the same with the 2nd step of Clean Air Filter)
3. Take out air inlet grille
Open air inlet grille for an angle of 45°, as shown in fig. 21, rise it.
4. Clean
Clean it by pubescence brush, water and neutral cleaning, then throw water or dry it.
Note !
Do not use water above 45℃ to wash the panel to prevent fade or deformation.
5. Install air inlet grille (refer to 3rd step)
6. Install air filter (refer to the 4th step of Clean Air Filter)
7. Close air inlet grille (refer to the 1st step)
★ Install and change of air purifier
1. Open air inlet grille (the same the 1st step of Clean Air Filter)
2. Disassembly purifier
As shown in fig 22, disassembly air filter, screw out fixing bolts fixed on purifier on filter, then purifier
could be disassembly.
3. Take out the package sack of static fiber net filter, then install the filter in stand of purifier, and fix
purifier on air filter.
4. Install air filter (the same with the 4th step of Clean Air Filter)
Air filter
Purifier filter
Stand for purifier
Fix bolt of
purifier
Fig.22
17
Function and usage period for air purifying
◆ Could adsorb CO, CO2, benzene, aldehydes and odor of gasoline etc..
◆ Could adsorb deleterious material that is smaller than 1μm in air, as dust, pollen, bacteria, and virus.
◆ Usage period is 6 months to 1 year. If it is necessary to be changed, purchase new purifier in the
nearest special engaged maintenance center.
★ Clean Outlet vent and Surface Panel
◆ Clean the surface panel by soft dry cloth or wet cloth with neutral scourer.
◆ It is forbidden to clean surface panel by gasoline, benzene, diluents, cleansing powder etc..
◆ If the guide louver is too dirty, it may be removed to be cleaned. (As narrated below)
Disassembly and install of guide louver
1. Disassembly guide louver
Screw bolts in both end of guide louver to loose.
Note !
Do not wipe guide louver powerfully when cleaning, otherwise fluff on surface would fall off.
2. Install guide louver
Rotate guide louver slightly could install the protruding edge of both end into grooves on both end of
guide louver, and then tighten bolts.
★ Maintenance before or after usage season
Check before the usage season
◆ Check if there is blockage in inlet or outlet vent of air conditioner.
◆ Check if the earthing wire had earthed reliably.
◆ Check if the air filter had been installed well.
◆ In order to start up the air conditioner smoothly after long time’s turned off, turn on the main power
supply 8 hours before turning on the air conditioner.
Maintenance after usage season
◆ Clean filter and body of air conditioner.
◆ Cut off the main power supply of air conditioner.
◆ The cooling or heating capacity and sound level are tested before leaving factory.
◆ If the parameter changed, refer to the data offered on nameplate.
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement