SF100 USER MENUAL
User Manual
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Contents
1 SF100 Profile.................................................................................................... 1
2. System Installation .......................................................................................... 4
2.1 Installation Notices ..................................................................................... 4
2.2 Device Installation ...................................................................................... 5
2.3 System Installation Sketch Map................................................................... 7
3. Connection with the peripheral devices .......................................................... 9
3.1 Connection with access controller................................................................ 9
3.2 Connection with door lock ........................................................................ 10
3.3 Connections with exit button, alarm, doorbell, and door sensor................... 13
3.3.1 Door sensor ....................................................................................... 13
3.3.2 Exit button ........................................................................................ 13
3.3.3 Alarm................................................................................................ 14
3.3.4 Doorbell............................................................................................ 14
3.4 Power supply............................................................................................ 14
4. Basic operations ............................................................................................ 15
4.1 Enroll a administrator................................................................................ 16
4.2 Enroll a user ............................................................................................. 18
4.3 User authentication ................................................................................... 19
4.4 Delete a user............................................................................................. 20
4.5 Delete all users ......................................................................................... 21
4.6 Fingerprint enrollment sub-flow and overtime judgement sub-flow ............ 22
5. Communications ........................................................................................... 24
Statement on Human Rights and Privacy......................................................... 26
I
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Environmental protection use explanation ....................................................... 28
II
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
1 SF100 Profile
1. Basis features
Ø
Ø
Ø
Ø
Easy installation, high reliability
Simple and clear operation flow, voice prompts in the operations.
Support the ID / MF card, a wider use range.
Support the backup authentication, stronger function (also with the
extension function).
Basic function parameters are shown as follows:
Power
DC12V
Function
Access control device with the
detection functions such as door
sensor, device dismantled etc.
User number
200 (fingerprint, ID card and MF
card)
Record memory
30000 records
communication
USB
RS232/485
running)
(device
monitors the
Fingerprint head
Optical fingerprint head
Door bell
Support the wired doorbell
Speaker
The voice prompts
Buzzer
Alarm when the device is dismantled
LED
Three-color indicate (Red, green,
blue)
1
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Language
Support multi-national voices
Sleep
Support the sleep function
Explanation:
1. Access control function: support the access control output, door
sensor alarm, exit button, but not support time segment, duress
alarm etc. It is a comparatively simple access control.
2. Sleep function: during sleeping, the backlight of fingerprint head
is turned off and Led displays, if any key is pressed (except the Bell
key), it will be waked up automatically to work normally.
2. Panel introduction
The front panel
LED
the indicator light with three
colors of red, blue, green.
Enroll key: it
is also used as
exit key during
the enrollment.
fingerprint
reader
Delete key: it
is also used as
exit key during
the deletion.
finger buckle
cover
doorbell key
2
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
Back panel:
Anti-dismantle button: Send
out the alarm signal through
the terminal when the device
is removed.
Speaker (mainly used in voice prompt)
Bottom Panel
USB interface
Reset key
Press this key to restart device if
device can not run normally due to the
error operations or other accidents.
3
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
2. System Installation
2.1 Installation Notices
Our products are mass-produced and in accordance with the strict
production and testing standards in China, the United States and the
European Union, but we hope you read the installation notices carefully
before the installation. The company to remind you the proper use, will
greatly improve your use effect and speed. If you don’t read the notes
carefully before the installation, probably because of improper
installation will cause a very serious accident damage, even though we
make every effort to provide you with good service, and you will have
to pay an unnecessary price.
1. Please connect the power supply later after all other wires are
connected well. If the machine cannot run normally, please cut off the
power and then start examination. Please remember: All connection
wires with power will damage the machine accidentally. We won’t
provide maintenance for such damage.
2. Recommend the use of 3A/12V DC power supply to the equipment.
For details, consult the relevant technical staff.
3. Please firstly read explanations of connection terminals carefully and
then connect the wires in strict accordance with the rules, due to
abnormal operations may result in equipment damages, do not belong to
the scope of warranty
4. All external connection wires are forbidden to be bared, both
connections and useless ends of wires must be bandaged with insulating
tape to prevent the accident contact of bared wires, which cause the
machine damage.
4
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
5. To prevent excessive instantaneous electrostatic damage to the
machine in winter or the place with a comparatively serious static,
please connect the ground wire firstly, then connect the other wires.
6. If the distance between power supply and machine is long, please
don't use the net cable or other types of lines to take place of power cord.
While selecting power cord, voltage attenuation caused by overlong
transmission distance should be taken into account.
7. When use 485 to organize a network, please use the professional 485
bus and RS232/485 transformer with power, and adopt the bus-type
wiring. If RS485 communication distance is over 300 meters, add a
terminal matched resistor about 120Ω to the RS485 bus.
8. Please use the access control software to connect the machine and
enroll users.
2.2 Device Installation
screw holes and lead wire hole)
2) Take the waterproof glue away
from the rear cover
1) Post the moulding board on the
wall. Drill holes according to marks
on the moulding. (There should be
5
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
(3)Take the finger buckle cover
away from the device
(4)Use screws to fix the device
and waterproof glue on the wall.
(5)At last, install the finger buckle cover well to
complete the device installation.
6
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
2.3 System Installation Sketch Map
1.When a person has passed the status authentication on the access
control device, the device will output the lock control signal to unlock.
2. Door sensor will automatically detect the switch state, when the door
is accidentally opened or the door is not closed well, it will trigger the
alarm signal (switch volume signal).
3. If the access control device is in unusual circumstances such as illegal
demolition etc., it will output the alarm signal (switch volume signal).
4. External wired doorbell can be connected.
5. External exit button can be connected, so it is convenient to open the
door from the indoors.
6. Through RS485/RS232/USB to connect with PC and transfer data to
PC, you can easily manage multiple terminal devices through access
control management software.
7
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Note: The alarm and the wired doorbell are required to connect an
external power supply.
8
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
3. Connection with the peripheral devices
3.1 Connection with access controller
SF100 as a fingerprint reader, with the standard Wiegand26 output, can
be connected with the access controllers on the market of the majority
manufacturers
In the reader mode, no operations such as the enrollment, the deletion
and so on, also no door sensor to detect and unlock, only the input of the
card and the fingerprint. During brushing the card, it outputs the card
number to the host through the Wiegand. During reading the fingerprint,
it outputs the ID number verified successfully to the host through the
Wiegand. Use the PC software to change the device’s working modes.
Anti-dismantle alarm is still availability in the reader mode.
Note: The function of weigand is availability only in the reader mode.
Note:
1) The recommended distance between device and access controller
should not be more than 90 meters (If a longer distance or an
environment with interference, please use the Wiegand signal extender).
9
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
2) Regardless of whether the device shares power supply with the access
controller, the device must share the ground with the access controller to
guarantee the stability of Wiegand signal.
3) When the device is used as a reader, RED, GREEN, BUZZER are
regarded as the input signals. The status of both the reader’s LED and
the buzzer are controlled by the access controller.
3.2 Connection with door lock
The device is able to support NO (normally open) and NC (normally
closed) locks, only if connected with different terminals. NO terminal
should be used for NO lock, which is open during power on and closed
during power off. And NC terminal should be used for NC lock, which
is closed during power on and opened during power off.
1. Device and lock share power supply
※Note: In case that device and lock share the power supply:
When ULOCK=12V, I-ILOCK>1A((thereinto, ULOCK is the operate
voltage of lock, I is the output current of device’s power supply, ILOCK is
the operate current of lock.) And the distance between lock and device is
closer.
(1) NC lock
10
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
SF100
NC Lock
(2) NO lock
SF100
NO Lock
2. Device and lock do not share power supply
※Note: In case that device and lock don’t share power supply:
1)ULOCK=12V and I-ILOCK≤1A;
2)ULOCK≠12V;
(3) A long distance between device and lock.
(thereinto, ULOCK is the operate voltage of lock, I is the output current of
device’s power supply, ILOCK is the operate current of lock.)
11
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
(1)NC lock
SF100
Lock Power
NC Lock
(2)NO lock
SF100
NO Lock
DC Power
12
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
3.3 Connections with exit button, alarm, doorbell, and door
sensor
SF100
3.3.1 Door sensor
Door sensor is used to detect the door’s on/off status. The
fingerprint access control device can use it to detect the door is opened
illegally, and at this time it will output the alarm. In addition, if the
opened door is not closed well in the regulated time, it also will output
the alarm.
3.3.2 Exit button
Exit button is a door-open switch installed inside the room and it is
closed to open the door. Please fix it at a place which is about 1.4 meter
high from the ground. Please ensure its location is positive and not
askew, while its connection is accurate and firmly. (Cut off the bared
side of unused cable and wrap it with the insulating tape.) Please pay
attention to prevent the electromagnetic interference. (For example:
lighting switch, computer, etc.)
13
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
3.3.3 Alarm
The alarm output of this fingerprint access control device is an on-off
signal. It can be put in series to the power circuit of a simple alarm. Of
course, it can also be used as a trigger signal of the advanced alarm or
the monitoring system. (The alarm output of the device only supports
the 12VDC alarm.)
3.3.4 Doorbell
The device can only use the doorbell with control pin. The doorbell
connected with power supply directly is not recommended.
3.4 Power supply
The device’s working power is DC12V. The working current is less than
300mA and the standby current is less than 200mA. Connect the
positive and negative poles of power supply between +12V and AGND
directly to work normally. (Don’t connect the positive and negative
poles in reverse.)
14
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
4. Basic operations
When power on, the device is in authenticating state. At this time the
user can enter into the states of user enrollment, administrator
enrollment, delete a user, and empty users. Each process is prompted by
the voice and the indicator light.
The operation processes are described as follows:
1. In authenticating state, if no enrolled fingerprint and card, the voice
‘Please press the Enroll key long to enroll a administrator’ prompts the
user to enroll a administrator as soon as possible.
2. User must enroll at least one administrator firstly before the normal
users can be enrolled.
3. During the enrollment, if no operation consecutively for n seconds
(set by the user), duplicate the corresponding voice prompt. After two
times consecutively voice prompts, system will return to the
authenticating status automatically. In the deletion state, system will exit
as soon as the first overtime
4. MF card can only support the same and simple functions of ID card
such as the enrollment and the deletion.
5. During the enrollment or the deletion, if consecutively three times
failed confirmations by the user, system will return to the authenticating
state with the prompt voice ‘A failed administrator confirmation, system
will return to the authenticating state’
6. During the enrollment or the deletion, if press the Enroll key or the
Delete key by the user, system will exit from the enrollment or the
15
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
deletion state automatically, and there are voice prompts.
7. During deleting a user, the last administrator can not be deleted.
8. During deleting a user, the administrator confirmation is not required,
but it is a must when delete all users.
9. When the enrolled fingerprints or cards are full, system will return to
the authenticating state with the prompt voice ‘Users are already full,
system exits!’.
10. There is a voice prompt when the records are full, and then the later
record can not be saved. At this time, users can mange the records by
connecting to the access control software.
11. Other Tips
a: In authenticating (verification)state, blue LED will flash once per 1/2
second. During enrollment and deletion, no flashed LED displays.
b. If a successful authentication or enrollment or deletion, green led will
be constant on for a second; If a failed authentication or enrollment or
deletion, red LED will be constant on for a second.
c. When users open the door normally, 3 seconds after the lock is locked
up, if the device detects the door sensor has not been closed well, the
buzzer will work long to prompt; 1 minute later, if the door sensor is still
not closed well, the alarm will work..
4.1 Enroll a administrator
The steps to enroll a administrator are shown in the following flow
chart:
16
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Voice prompt:
a:Please try again. b:
Enter into the ‘Admini-
Please punch card again
strator enrollment’ status
Please confirm with
Administrator faied to
the administrator. Pr-
confirm,System back
ess ‘Enroll’ button to
to validated status
exit
please Press fingerprint
or punch card. Press
‘Enroll’ button to exit
Users are full,
System back to
validated status
Duplicated
card number
a : Duplicated
user ID xxx,
finger; b:Please
Enrollment
try again.
succeeded.
Note: The overtime judgement sub-flow and the fingerprint enrollment
sub-flow, please refer to the section 4.6.
17
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
4.2 Enroll a user
Each user can only enroll a fingerprint or a card, the range of user ID is
1~999.
The operation steps are shown as the following flow chat.
Extended press the
Enter into the ‘user
‘Enroll’
enrollment’ status
enroll a administrator
button
to
a:Please try again. b:Please punch card again
Please confirm with
the administrator. Press ‘Enroll’ button to
exit
please Press fingerprint
or punch card. Press
Administrator fai-
‘Enroll’ button to exit
ed
to
confirm,
System back to
validated status
Users are full,
System back to
validated status
Duplicated
card number
a:Duplicated finger
b:Please try again.
18
user ID xxx,Enrollment
succeeded.
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
Note: The overtime judgement sub-flow and the fingerprint enrollment
sub-fow, please refer to the section 4.6.
4.3 User authentication
The steps to authenticate users are shown as the following flow chart:
User verified, please
press fingerprint or
punch card
Please punch
card again
Please try again
user ID xxx,
Thank you
19
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
4.4 Delete a user
The operation steps are shown as the following flow chart:
The validated
status
No users enrolled,
Click and press
the Delete Key
Enter into the ‘Delete a
NO
user’ status , Please
confirm
with
administrator,
System
back
to
YES
validated status
Exit an enrolled
user?
the
a:Please try again
Press
‘Delete’ button to exit
YES
b : Please punch
NO
card again
Success to
confirm the
administrator?
Delete a user ,please
ress
punch
fingerprint
card,
or
Failed to
confirm for 3
times?
NO
administrator failed to confirm
YES
System back to validated status
Press
‘Delete’ button to exit
brush a card to
confirm by the user
Press FP to confirm
by the user.
NO
Time out for
5S?
NO
NO
Success to
confirm the
card?
Please punch
ration timed o-
Success to
confirm the FP?
ut, System back to validated
YES
card again
Please try
Forbid to delete the last
System
back to validated status
YES
status
again
The last
administrator?
administrator
Deletion ope-
Return to
validated status
YES
Delete successfully,
System
back
to
validated status
20
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
4.5 Delete all users
The operate steps are shown as the following flow chart.
No users enrolled,
System
Enter
the
into
back
to
validated status
‘clear
user’ status
a:Please try again
b : Please punch
Please confirm with the
administrator,
card again
Press
‘Delete’ button to exit
administrator failed to confirm,
System back to validated status
Clear users
successfully
Delete failed,System
back
to
validated
status
Please long press ‘Delete’ key
System back to
to clear the administrator.
validated status
Press ‘Delete’ button to exit
‘Clear
administrator’
successfully,
System
Delete failed,System back
back to validated status
to validated status
21
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
Note: The overtime judgement sub-flow, please refer to the section 4.6
4.6 Fingerprint enrollment
judgement sub-flow
sub-flow
and
overtime
4.6.1 Fingerprint enrollment sub-flow
The operation steps are as the following flow chart.
The enrollment states
of fingerprint or card
Please try
NO
Please press the
finger again
Success to
press FP for the
first time?
YES
NO
again
Please try
again
Success to
press FP for the
second time?
Please press the
fingerprint
the last time
for
NO
YES
Please try
Success to
press FP for the
third time?
again
YES
Success to enroll FP
22
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
4.6.2 Overtime judgement flow when enrolling or deleting a user
The operation steps are shown as the following flow chart.
FP enrollment
status
Time out for 4s?
NO
YES
Twice
duplications?
Enrollment(deletion)
NO
operation timed out,
System
YES
Return to the
validated status
back
to
validated status
23
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
5. Communications
The background PC software can communicate with the device
through three methods (RS232, RS485, USB), and then exchange the data.
RS485 can also be used for the remote management.
1. RS232 communication
PC serial port
2. RS485 communication
24
PDF 文件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn
SF100 user manual V1.0
3. USB communication
After device is connected with PC well, do the operations as follows:
Ø
Upload the user’s open door records.
Ø
Upload and download the user information.
Ø
Parameter setting, function configuration.
The detail operation about data by the access control software, please refer
to <<access control software manual>>.
25
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Statement on Human Rights and Privacy
Dear Customer:
First of all, Thank you for using the identification product designed and
produced by us. As the world famous provider of leading identification
technology, we attach great importance to the law involved in human rights
and privacy in every county.
Therefore, we have the following statement:
1. Our civilian identification equipments only capture character points
rather than images, not concerning in retaining privacy.
2. The captured character points cannot recover the original image, not
involved in privacy.
3. We (as provider of equipments) have no direct or indirect legal liabilities
for any negative consequences arising from using the equipment.
4. If you have dispute about human rights or privacy, please contact your
employer.
Our other police equipment or development tools will provide function to
capture citizens’ original image. As for right infringement, please contact
government or the equipment’s ultimate provider. We have no any legal
liabilities for it.
Notice: Chinese law provides citizen personal freedom rights, including the
following:
1. The person is free from unlawful arrest, detention, search and
infringement.
2. Personal dignity related with personal freedom is out of infringement.
3. Citizen’s residence is inviolable.
4. Citizen’s communication freedom and privacy are protected by law.
26
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
For password insecurity, people all over the world are suffering great
damages. The advanced identification technology will enter e-commerce,
bank, insurance, law affair and other industries in the near future.
Identification in high-security environment ensures you real protection.
27
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Environmental protection use explanation
· The environmental protection use period marked on our
products is the safety period of our products used under the
conditions specified by this manual without toxic and harmful
substances leaking happened
· The environmental protection use period marked on our
products does not include the easy wear and tear components
required to be replaced regularly such as the battery etc. The
battery’s environmental protection use period is 5 years.
The toxic and harmful substances or element names and the content
table
The toxic and harmful substances or elements
Part name
Lea
mercur
Cadmiu
Hexavalen
Polybrominate
Polybrominate
d
y (Hg)
m (Cd)
t
d
d
Chromium
(PBB)
(Pb)
biphenyls
diphenyl
ethers (PBDE)
(Cr6 +)
×
○
○
○
○
○
×
○
○
○
○
○
×
○
○
○
○
○
SMD diode
×
○
○
○
○
○
ESD
×
○
○
○
○
○
×
○
○
○
○
○
SMD
resistor
SMD
capacitor
SMD
inductance
component
s
Buzzer
28
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
SF100 user manual V1.0
Adapter
×
○
○
○
○
○
Screw
○
○
○
×
○
○
○:Indicate that the content of the toxic and harmful substance contained in all
homogeneous materials of this part is in the limitation requirement stipulated in SJ /
T 11363-2006.
×:Indicate the content of the toxic and harmful substance contained in at least one
homogeneous material of this part is beyond the limitation requirement stipulated in
SJ / T 11363-2006.
Note: The 80% product has adopted the manufacture with non-toxic and harmless
environmental protection materials, the non-toxic and harmless substances or
elements instead of the toxic and harmful substances or elements contained can not
be achieved because of the current technology and economic constraints
29
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement