Red Lion CSMSTRLE Modular Controller Datasheet

Red Lion CSMSTRLE Modular Controller Datasheet
Bulletin No. CSMSTRLE-D
Drawing No. LP0672
Released 05/11
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MODELS CSMSTRLE – ENHANCED MODULAR CONTROLLER SERIES MASTER
C
UL
R
 ADDS MULTIPLE PROTOCOL CONVERSION FUNCTIONALITY
TO DATA ACQUISITION AND MULTI-ZONE PID CONTROL
APPLICATIONS
US LISTED
IND. CONT. EQ.
34AD
 PERFORMS HIERARCHICAL CONTROL OF OTHER MODULES
IN THE MODULAR CONTROLLER SERIES
 STORES MODULE CONFIGURATION INFORMATION, AND
AUTOMATICALLY REPROGRAMS REPLACED MODULES
 EXTENSIVE BUILT-IN DRIVER LIST ALLOWS EASY DATA
MAPPING TO PLCs, PCs, AND SCADA SYSTEMS
 INDEPENDENT SERIAL PORTS PROVIDE VIRTUALLY
UNLIMITED INTEGRATION METHODS
 10 BASE-T/100 BASE-TX ETHERNET CONNECTION PROVIDES
NETWORKING CAPABILITY
 SUPPORTS UP TO 16 MODULAR CONTROLLER SERIES
MODULES
C
UL
R
 SUPPORTS UP TO NINE PROTOCOLS
SIMULTANEOUSLY(with expansion card)
US LISTED FOR USE IN HAZARDOUS LOCATIONS:
3PWL
PROGRAMMABLE
CONTROLLERS
Class I, Division 2, Groups A, B, C, and D
GENERAL DESCRIPTION
SOFTWARE
The CSMSTR is programmed with Crimson® 2.0 software for Windows®
2000 or later platforms. The software is an easy to use, graphical interface which
provides a means of communication configuration, as well as commissioning
and calibration of new systems.
The Model CSMSTRLE is a communications and control platform designed
for use with Modular Controller Series slave modules. The CSMSTR uses a
proprietary high speed serial protocol to communicate, via backplane connection,
with up to 16 slave modules. Through the same connection, the Master also
provides power to the modules.
When powered up, the CSMSTR automatically identifies and addresses
connected slave modules. By storing the configuration information of all of the
modules, the CSMSTR is able to automatically configure modules if they are
replaced.
The Master provides high-speed RS232/422/485 communication ports and an
Ethernet port for connection to PCs, PLCs, and SCADA systems. An extensive
list of master and slave protocol drivers are available to allow the CSMSTR to
share and exchange variable data with external devices. The 10 Base-T/100
Base-TX Ethernet port can also be used to connect and share data with other
devices at high speeds.
The design of the Modular Controller Series high density packaging and DIN
rail mounting saves time and panel space. The controller snaps easily onto
standard top hat (T) profile DIN rail.
CONTENTS OF PACKAGE
- CS Master
- Termination Plug
- Terminal Block for connecting power.
- Rubber End Cap
SAFETY SUMMARY
All safety related regulations, local codes and instructions that appear in the
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
Do not use the controller to directly command motors, valves, or other
actuators not equipped with safeguards. To do so can be potentially harmful to
persons or equipment in the event of a fault to the controller. An independent
and redundant temperature limit indicator with alarm outputs is strongly
recommended.
DIMENSIONS In inches (mm)
3.09 (78.5)
4.15 (105.4)
CAUTION: Risk of Danger.
Read complete instructions prior to installation
and operation of the unit.
RS232/PG
STS
USB/PG
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF
COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2
CF
RS485
RS232
5.30
(134.7)
THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I,
DIVISION 2, GROUPS A, B, C, D, OR NON-HAZARDOUS
LOCATIONS ONLY
ETHERNET
CompactFlash is a registered trademark of CompactFlash Association.
1
SPECIFICATIONS
10. CERTIFICATIONS AND COMPLIANCES:
SAFETY
Check each module’s specifications to determine system compliance.
UL Listed, File #E302106, UL508, CSA 22.2 No. 14-M05 and File #E179259,
UL61010-1, CAN/CSA-C22.2 No. 61010-1; and File #E317425, ANSI/ISA
12.12.01-2007, CSA 22.2 No. 213-M1987
LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards
IECEE CB Scheme Test Report #E179259-A5-CB-1
Issued by Underwriters Laboratories Inc.
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
for measurement, control, and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: 2006: Electrical Equipment for
Measurement, Control and Laboratory use.
Immunity to Industrial Locations:
Electrostatic discharge
EN 61000-4-2 Criterion B
4kV contact discharge
8kV air discharge
Electromagnetic RF fields EN 61000-4-3 Criterion B3
10V/m (80 MHz to 1 GHz)
3 V/m (1.4 GHz to 2 GHz)
1 V/m (2 GHz to 2.7 GHz)
Fast transients (burst)
EN 61000-4-4 Criterion B
power 2kV
I/O signal 1kV
I/O signal connected to power 2kV
Surge
EN 61000-4-5 Criterion B
power 1 kV L to L, 2 kV L to G
signal 1 kV
RF conducted interference EN 61000-4-6 Criterion A
3 Vrms
Emissions:
Emissions
EN55011
Class A
1. POWER: 24 VDC ± 10%
400 mA min. (1 module)
3.5 Amps max. (16 modules + Expansion Card)
Must use NEC Class 2 or Limited Power Source (LPS) rated power supply.
2. COMMUNICATIONS:
USB/PG Port: Adheres to USB specification 1.1. Device only using Type B
connection.
WARNING - DO NOT CONNECT OR DISCONNECT CABLES
WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND
DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT
CONNECTION.
Serial Ports: Format and Baud Rates for each port are individually software
programmable up to 115,200 baud.
RS232/PG Port: RS232 port via RJ12
COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12
DH485 TXEN: Transmit enable; open collector, VOH = 15 VDC,
VOL = 0.5 V @ 25 mA max.
Ethernet Port: 10 BASE-T / 100 BASE-TX
RJ45 jack is wired as a NIC (Network Interface Card).
3. LEDs:
STS – Status LED indicates condition of master.
TX/RX – Transmit/Receive LEDs show serial activity.
Ethernet – Link and activity LEDs.
CF – CompactFlash LED indicates card status and read/write activity
4. MEMORY:
On-board User Memory: 4 Mbytes of non-volatile Flash memory.
On-board SDRAM: 2 Mbytes
Memory Card: CompactFlash Type II slot for Type I and Type II cards.
Used for optional database storage only.
5. REAL-TIME CLOCK: Typical accuracy is less than one minute per month drift.
Battery: Lithium Coin Cell. Typical lifetime of 10 years at 25 ºC.
A “Battery Low” system variable is available so that the programmer can
choose specific action(s) to occur when the battery voltage drops below
its nominal voltage.
This unit is NOT field serviceable. All work must be done by a qualified technician.
6. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: 0 to 50°C
Storage Temperature Range: -30 to +70°C
Operating and Storage Humidity: 80% max relative humidity,
non-condensing, from 0 to 50°C
Vibration According to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z
direction for 1.5 hours, 2 g.
Shock According to IEC 68-2-27: Operational 25 g, 11 msec in 3 directions.
Altitude: Up to 2000 meters
7. CONSTRUCTION: Case body is burgundy high impact plastic and stainless
steel. For indoor use only. Installation Category II, Pollution Degree 2.
8. POWER CONNECTION: Removable wire clamp screw terminal block.
Wire Gage Capacity: 24 AWG to 12 AWG
Torque: 4.45 to 5.34 in/lb (0.5 to 0.6 N-m)
9. MOUNTING: Snaps onto standard DIN style top hat (T) profile mounting
rails according to EN50022 -35 x 7.5 and -35 x 15.
Notes:
1. Criterion A: Normal operation within specified limits.
2. Criterion B: Temporary loss of performance from which the unit self-recovers.
3. The module’s with analog input and/or output signals may have their
signals deviate during disturbance but self-recover when the disturbance
is removed.
11. WEIGHT: 15.1 oz (456.4 g)
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR
AREA IS KNOWN TO BE NON-HAZARDOUS.
2
HARDWARE
INSTALLATION
DIN rail should be mounted horizontally so that the unit’s ventilation holes
are vertical in relation to cabinet orientation. A minimum clearance of 1 inch
(25.4 mm) should be maintained above and below the unit in order to ensure
proper thermal regulation.
The unit shall be installed inside a UL Listed Industrial Control Panel or
similar type of enclosure. A minimum 3.2 mm distance shall be maintained
between the hazardous live parts of the equipment and accessible parts of the
fire/electrical enclosure.
TOP
1.00"
DEPRESS
min. clearance
3
RS232/PG
STS
4
USB/PG
1
CF
RS485
DIN RAIL
RS232
4
ETHERNET
1.00"
min. clearance
REMOVE
2
BOTTOM
Figure 1 - Attach CSMSTR Master To DIN Rail and Remove
Rubber End Cap
Figure 2 - Attach Slave Bases To DIN Rail
RS232/PG
STS
RS232/PG
STS
USB/PG
CF
USB/PG
RS485
CF
DIN RAIL
RS485
5
DIN RAIL
RS232
RS232
ETHERNET
ETHERNET
Figure 4 - Installation Complete
Figure 3 - Attach Termination Plug*
* Supplied with CSMSTRLE Master Module.
COMPACTFLASH® CARD
Mount the Master as shown under Hardware Installation Figure 1 above.
Install the rubber end cap. The end cap protects the pins from damage. Configure
the Master for zero modules.
CompactFlash socket is a Type II socket that can accept either Type I or II
cards. Use cards with a minimum of 4 Mbytes and a maximum of 2 Gbytes with
the Master’s CompactFlash socket. Cards are available at most computer and
office supply retailers. CompactFlash can be used for configuration transfers, data
logging, and trending.
CompactFlash
(Top Side)
PROTOCOL CONVERSION
CompactFlashInsert Top Side
Towards Left
Note: Do not remove or insert
the CompactFlash card while
power is applied.
NOTE
For reliable operation of this and other Red Lion products, one of the
following brands of CompactFlash card must be used...
SimpleTech
SanDisk®
Information stored on a CompactFlash card can be read by a card reader
attached to a PC. This information is stored in IBM (Windows®) PC compatible
FAT16 file format.
SMART® Modular
Silicon Systems
Not all of the above manufacturers offer CompactFlash cards recognized
to UL standards, which may be required for your application.
3
POWER SUPPLY REQUIREMENTS
is near a commercial radio transmitter. Also, Signal or Control cables within
an enclosure should be routed as far away as possible from contactors, control
relays, transformers, and other noisy components.
5. Long cable runs are more susceptible to EMI pickup than short cable runs.
Therefore, keep cable runs as short as possible.
6. In extremely high EMI environments, the use of external EMI suppression
devices is effective. The following EMI suppression devices (or equivalent)
are recommended:
Ferrite Suppression Cores for signal and control cables:
Fair-Rite part number 0443167251 (RLC part number FCOR0000)
TDK part number ZCAT3035-1330A
Steward part number 28B2029-0A0
Line Filters for input power cables:
Schaffner part number FN610-1/07 (RLC part number LFIL0000)
Schaffner part number FN670-1.8/07
Corcom part number 1 VR3
Visit RLC's web site at www.redlion.net for more information on EMI
guidelines, Safety and CE issues as they relate to Red Lion Controls products.
It is very important that the power supply is mounted correctly if the unit is
to operate reliably. Please take care to observe the following points:
– The power supply must be mounted close to the unit, with usually not more
than 6 feet (1.8 m) of cable between the supply and the master. Ideally, the
shortest length possible should be used.
– The wire used to connect the master’s power supply should be at least
22-gage wire. If a longer cable run is used, a heavier gage wire should be
used. The routing of the cable should be kept away from large contactors,
inverters, and other devices which may generate significant electrical
noise.
– A power supply with an NEC Class 2 or Limited Power Source (LPS) and
SELV rating is to be used. This type of power supply provides isolation to
accessible circuits from hazardous voltage levels generated by a mains
power supply due to single faults. SELV is an acronym for “safety extralow voltage.” Safety extra-low voltage circuits shall exhibit voltages safe
to touch both under normal operating conditions and after a single fault,
such as a breakdown of a layer of basic insulation or after the failure of a
single component has occurred.
Visit www.redlion.net for a complete list of our PSDR Series of NEC Class 2
power supplies.
WIRING
POWER CONNECTION
EMC INSTALLATION GUIDELINES
Although Red Lion Controls Products are designed with a high degree of
immunity to Electromagnetic Interference (EMI), proper installation and wiring
methods must be followed to ensure compatibility in each application. The type
of the electrical noise, source or coupling method into a unit may be different
for various installations. Cable length, routing, and shield termination are very
important and can mean the difference between a successful or troublesome
installation. Listed are some EMI guidelines for a successful installation in an
industrial environment.
1. To reduce the chance of noise spikes entering the unit via the power lines,
connections should be made to a clean source. Connecting to circuits that also
power loads such as contactors, relays, motors, solenoids etc. should be avoided.
2. The unit should be mounted in a metal enclosure, which is properly connected
to protective earth.
3. Use shielded (screened) cables for all Signal and Control inputs. The shield
(screen) pigtail connection should be made as short as possible. The
connection point for the shield depends somewhat upon the application.
Listed below are the recommended methods of connecting the shield, in order
of their effectiveness.
a. Connect the shield to earth ground (protective earth) at one end where the
unit is mounted.
b. Connect the shield to earth ground at both ends of the cable, usually when
the noise source frequency is over 1 MHz.
c. Connect the shield to common of the master and leave the other end of the
shield unconnected and insulated from earth ground.
4. Never run Signal or Control cables in the same conduit or raceway with AC
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be run through metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
COMMON
+24 VDC
INPUT AND OUTPUT (I/O) WIRING MUST BE IN
ACCORDANCE WITH CLASS I, DIV. 2 WIRING METHODS
AND IN ACCORDANCE WITH THE AUTHORITY HAVING
JURISDICTION.
RS232
RS232/PG
CBLPROG0
RS232/PG
USB/PG
STS
OR
USB/PG
CF
RS485
CBLUSB00
RS232
ETHERNET
ETHERNET
+24
N/C
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT
WHILE CIRCUIT IS ALIVE UNLESS AREA IS KNOW TO BE
NON-HAZARDOUS.
PROGRAMMING PORTS
CTS
Rx
COMM
COMM
Tx
RTS
COMM
OR
GREEN/AMBER LED
Ethernet (Crossover)
YELLOW LED
4
COMMUNICATION PORTS
RS232
RS232/PG
CTS
Rx
COMM
COMM
Tx
RTS
CBLPROG0
RS232/PG
STS
USB/PG
CF
RS485
OR
RS232
ETHERNET
POWER
SLC 5/03 CPU
RUN
FORCE
FLT
DH485
RS232
BATT
RUN
REM
PROG
PWR OUT +24
VDC
PWR OUT COM
USER
POWER
120/240 VAC
VAC NEUT
CHASSIS GND
CBLxxxxx*
RS232
RS232/PG
STS
USB/PG
RS232
RTS
Tx
COMM
COMM
Rx
CTS
POWER
SLC 5/03 CPU
RUN
CF
FORCE
FLT
DH485
BATT
RS232
RUN
REM
PROG
RS485
RS232
PWR OUT +24
VDC
PWR OUT COM
USER
POWER
120/240 VAC
VAC NEUT
* Use appropriate communications cable. See Ordering
Information for descriptions of the available cables.
CHASSIS GND
CBLxxxxx*
ETHERNET
WARNING: Do NOT use a standard DH-485
cable to connect this port to Allen Bradley
equipment.
RS485
RS232/PG
STS
POWER
SLC 5/03 CPU
RUN
FORCE
FLT
DH485
BATT
RUN
USB/PG
RS232
REM
PROG
CF
RS485
TxA
TxB
COMM
TxEN
RxB
RxA
TxA
TxB
RS485
PWR OUT +24
VDC
PWR OUT COM
120/240 VAC
VAC NEUT
CHASSIS GND
RS232
CBLxxxxx*
ETHERNET
PORT 3 - ETHERNET CONNECTION
RS232/PG
STS
GREEN/AMBER LED
USB/PG
CF
RS485
YELLOW LED
RS232
Standard Ethernet cable
ETHERNET
5
USER
POWER
MASTER PORT PIN OUTS
CTS (PIN 1)
Rx
COMM
COMM
Tx
RTS (PIN 6)
1
COMMON
2
24VDC ±10%
3
N/C
POWER
CONNECTOR
RS232
RS232/PG PORT
RS232/PG
STS
TROUBLESHOOTING
USB/PG
If for any reason you have trouble operating,
connecting, or simply have questions concerning your
new Master, contact Red Lion’s technical support. For
contact information, refer to the back page of this bulletin
for phone and fax numbers.
TxB (PIN 1)
TxA
RxA
RxB
TxEN
COMM
TxB
TxA (PIN 8)
USB/PG
CF
EXPANSION
PORT
RS485
RS485
CTS (PIN 1)
Rx
COMM
COMM
Tx
RTS (PIN 6)
COMMS
PORT
RS232
EMAIL: [email protected]
Web Site: http://www.redlion.net
ETHERNET
RS232
YELLOW
LED
GREEN/
AMBER
LED
COMMS
PORT
ETHERNET
(NIC)
COMMUNICATING WITH THE MASTER
CONFIGURING A MASTER
ETHERNET COMMUNICATIONS
The Master is configured using Crimson® 2.0 software. Crimson 2.0 is
available as a free download from Red Lion’s website, or it can be ordered on
CD. Updates to Crimson 2.0 for new features and drivers are posted on the
website as they become available. By configuring the Master using the latest
version of Crimson 2.0, you are assured that your unit has the most up to date
feature set. Crimson 2.0 software can configure the Master through the RS232/
PG port, USB/PG port, Ethernet or CompactFlash. The USB/PG port is
connected using a standard USB cable with a Type B connector.
The driver needed to use the USB port will be installed with Crimson 2.0.
The RS232/PG port uses a programming cable made by Red Lion to connect to
the DB9 COM port of your computer. If making your own cable, refer to the
“Master Port Pin Outs” for wiring information.
The CompactFlash can be used to program a Master by placing a
configuration file and firmware on the CompactFlash card. The card is then
inserted into the target Master and powered. Refer to the Crimson 2.0 literature
for more information on the proper names and locations of the files.
Ethernet communications can be established at either 10 BASE-T or 100
BASE-TX. The Master’s RJ45 jack is wired as a NIC (Network Interface Card).
For example, when wiring to a hub or switch use a straight-through cable, but
when connecting to another NIC use a crossover cable.
The Crimson 2.0 manual contains additional information on Ethernet
communications.
RS232 PORTS
The Master has two RS232 ports. There is the RS232/PG port and the
COMMS port. Although only one of these ports can be used for programming,
both ports can be used for communications with a PLC. The RS232/PG port can
be used for either master or slave protocols.
RS422/485 PORT
The Master has one RS422/485 port. This port can be configured to act as
either RS422 or RS485.
CABLES AND DRIVERS
RS422/485 4-WIRE
CONNECTIONS
Red Lion has a wide range of cables and drivers for use with many different
communication types. A list of these drivers and cables along with pin outs is
available from Red Lion’s website. New cables and drivers are added on a
regular basis. If making your own cable, refer to the “Master Port Pin Outs” for
wiring information.
RS485 2-WIRE
CONNECTIONS
5V
5V
130K
130K
7
TX
USB, DATA TRANSFERS FROM THE
COMPACTFLASH CARD
1
TX/RX
8
8
130K
TxA
2
5
WARNING - DO NOT CONNECT OR DISCONNECT CABLES
WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND
DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT
CONNECTION.
7
TxB
TxB
1
TxEN (OC)
130K
TxA
2
5
TxEN (OC)
6
GND
5V
130K
In order to transfer data from the CompactFlash card via the USB port, a
driver must be installed on your computer. This driver is installed with Crimson
2.0 and is located in the folder C:\Program Files\Red Lion Controls\Crimson
2.0\Device\ after Crimson 2.0 is installed. This may have already been
accomplished if your Master was configured using the USB port.
Once the driver is installed, connect the Master to your PC with a USB cable, and
follow “Mounting the CompactFlash” instructions in the Crimson 2.0 user manual.
4
RxB
3
RxA
6
GND
RX
130K
Note: The USB port is for system set-up and diagnostics and is not intended for
permanent connection.
Note: All Red Lion devices connect A to A and B to B, except for Paradigm
devices. Refer to www.redlion.net for additional information.
6
DH485 COMMUNICATIONS
USER COMMUNICATION PORTS - TX/RX LEDS
The Master’s RS422/485 COMMS port can also be used for Allen Bradley
DH485 communications.
WARNING: DO NOT use a standard DH485 cable to connect this port to Allen
Bradley equipment. A cable and wiring diagram are available from Red Lion.
LED
INDICATION
GREEN
Transmitting
RED
Receiving
Note: LEDs are not available on the Programming Port: RS232/PG.
ETHERNET LEDS
LEDS
STS – STATUS LED
The green Status LED provides information regarding the state of the Master,
as well as the rest of the system. This includes indication of the various stages
of the start-up routine (power-up), and any errors that may occur.
Startup Routine
INDICATION
Rapidly Flashing
Master is currently running the boot loader and/or
being flash upgraded by Crimson.
Steady
Master is operating properly.
Error States
LED
INDICATION
1 blink, pause, repeat
One or more slave modules are missing from the
system. Master and installed modules will perform
normally in this state.
2 blinks, pause, repeat
Missing configuration, or configuration being
updated by Crimson.
3 blinks, pause, repeat
Quantity of module bases does not match
configuration file. Master will not communicate
with the modules until the error is corrected.
4 blinks, pause, repeat
Termination plug not installed, or one or more
bases are malfunctioning. Master will not
communicate with the modules until the plug is
reinstalled, and power is cycled.
CF LED
LED
INDICATION
Off
No CompactFlash Card is present.
Steady
Valid CompactFlash card is present.
Flashing Rapidly
CompactFlash card is being checked.
Flickering
Unit is writing to the CompactFlash, either
because it is storing data, or because the PC
connected via the USB port has locked the drive.
Flashing Slowly
Incorrectly formatted CompactFlash card present.
1
1. Do not turn off power to the unit while this light is flickering. The unit writes
data in two minute intervals. Later Microsoft operating systems will not lock
the drive unless they need to write data; Windows 98 may lock the drive any
time it is mounted, thereby interfering with logging. Refer to “Mounting the
CompactFlash” in the Crimson 2.0 User Manual.
7
LED
INDICATION
YELLOW (Solid)
Link Established
YELLOW (Flashing)
Network Activity
GREEN
10 BASE-T Communications
AMBER
100 BASE-TX Communications
ORDERING INFORMATION
TYPE
Master Module
MODEL NO.
CSMSTR1
Communications
Cables (10 feet)
CBL
Software
SFCRM2
Power Supply
Accessories
DESCRIPTION
PART NUMBER
Modular Controller Master, Comms, Ethernet
CSMSTRV2
Modular Controller Master with multiple protocol converter, Ethernet, and expansion slot.
CSMSTRLE
Modular Controller Master with multiple protocol converter, data logger, web server with Virtual
HMI up to QVGA (320 x 240) size and expansion slot.
CSMSTRSX
Modular Controller Master with multiple protocol converter, data logger, web server with Virtual
HMI up to VGA (640 x 480) size and expansion slot with increased SDRAM.
CSMSTRGT
RS232 Programming Cable
CBLPROG0
USB Cable
CBLUSB00
Communications Cables1
CBLxxxxx
Crimson 2.0 2, Modular Controller Manual, and Download Cable
SFCRM2MC
PSDR
DIN Rail Mounted Power Supply
PSDRxxxx
XCCN
CANopen option card for Modular Controller or Data Station Plus
XCCN0000
XCDN
DeviceNet option card for Modular Controller or Data Station Plus
XCDN0000
XCPB
PROFIBUS option card for Modular Controller or Data Station Plus
XCPBDP00
XCRS
RS232/485 option card for Modular Controller or Data Station Plus
XCRS0000
G3CF
CompactFlash Card
3
G3CFxxxx
Rail Stops (Qty 2)
RSRSTP00
Replacement Base
CSBASE00
Replacement Termination Plug
CSTERM00
Replacement Rubber End Cap
CSBUNG00
Note: Certain modules are not suitable for use in Hazardous locations. Check each module's specifications prior to installation.
1
Visit www.redlion.net for a complete list of PID modules, data acquisition modules, communications drivers and cables.
2
Use this part number to purchase Crimson on CD with a printed Modular Controller Manual, USB cable, and RS-232 cable. Otherwise, download free of
charge from www.redlion.net.
3
Industrial grade two million write cycles. SMART Modular Technologies model SG9CF (UL Listed Directory Category NWGQ).
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained
herein and relies on no other warranties or affirmations.
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls
Europe
Printerweg 10
NL - 3821 AD Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Red Lion Controls
India
54, Vishvas Tenement
GST Road, New Ranip,
Ahmedabad-382480 Gujarat, India
Tel +91 987 954 0503
Fax +91 79 275 31 350
Red Lion Controls
China
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113-3688
Fax +86 21 6113-3683
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement