- No category
advertisement
GRANDIO
G R E E N H O U S E S
Model GRA-ASC-88 / GRANDIO 8X8 ASCENT
Model GRA-88-GR Shown In Image
GREENHOUSE USER MANUAL
© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved
August 1, 2014 Manual Edition
GRANDIO
G R E E N H O U S E S
Dear Valued Customer,
We would like to congratulate you on your new
Grandio Greenhouse purchase. We are confident that you have made the right decision in choosing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come.
Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience.
Cheers!
Grandio Greenhouses
Save this owner’s manual for future reference and if you need our help.
CONTACT OUR CUSTOMER SERVICE
DEPARTMENT at:
1-866-928-3150
Hours: 8:30a.m.-5:00p.m. Monday through
Friday (Mountain Standard Time)
Backyard Living Source
9543 W. Emerald St., Suite 101
Boise, ID 83704 www.grandiogreenhouses.com
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY
Before you begin take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual, each piece should be labeled with a part number.
Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and opal film side faces inside greenhouse.
Plan out when and where you are going to place the greenhouse, we recommend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.
Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!
1
IMPORTANT! SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instruc-
tions and identify all parts using the hardware identifier and parts list on pages 35-40. Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.
CAUTION:
Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool
dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective film adhering to panels.)
• Remove approximately 2 inches of film from all polycarbonate sheet edges before installing. Remove all protective film immediately after the construction is completed.
Clear film side of panels should always face the sun and opal film side faces inside.
• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.
• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.
• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.
• If using a ladder during assembly, use extreme caution.
• Clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a firm and level base.
TOOLS YOU WILL NEED FOR ASSEMBLY
• Outdoor Construction Adhesive or Silicone Caulk
• Tape Measure
• Level
• Carpenter Square
• At Least 2 Adults
• Step Ladder
• Work Gloves
• Masking Tape
• Safety Glasses
• Flathead Screwdriver • 10mm Wrench
• No. 1, 2 and 3 Phillips Screwdrivers
GRANDIO
T I P
When you see this icon pay special attention to the helpful tips we have provided that will make installation more efficient.
2
PREPARE A FOUNDATION FOR YOUR
GRANDIO GREENHOUSE
Before assembling your new greenhouse a proper foundation must be prepared. A number of anchoring options are acceptable, based on wind and ground conditions in your area.
It is extremely important to have the area prepared and leveled for installation of your greenhouse prior to starting the assembly of your Grandio Greenhouse.
Decide at this time the final orientation of your
Greenhouse. We recommend that you place your greenhouse in a location where it will receive the most direct sunlight and will be best protected from wind and storm conditions.
Go to www.grandiogreenhouses.com for foundation ideas and tour our online learning center for tips and tricks for putting your greenhouse together.
GRANDIO GREENHOUSE DIMENSIONS
FOR 8X8 AND 8X12
All dimensions are the same except the sides for 8x8 verses 8x12 see measurements in .
90”
1
3
/
4
”
GUTTERS
54”
68”
IMPORTANT: POLYCARBONATE PANELS
BASE 3
1
/
4
”
Remove approximately 2 inches of film on both sides of each panel prior to installation. Remove all film immediately after assembly is complete. The UV-Protected side is covered with transparent film and must face toward the sun. The side covered in opal film will always face the interior of the greenhouse.
Sun
Transparent Film
8X12
8X8
144.5”
42”
FRONT WIDTH
Polycarbonate
Panels
Opal White Film
3
Outside View
601A-B
L08B-X
BACK
L08A
603B
Y4
603B
Y4
603C 603C
L08B-X
601A-B
L08B
Y7
L08C-X
602A
610
Y7
Y7
L08C-X
602A
Y7
L08C
603C/616
602A
LEFT SIDE
609-A
L08C
Y8
602B
L08C
602B
Y8
Y10
Y9
618
602B
Y8
610
Y2 Y5-2 Y5-1 Y1
609-A
610
615
601A-FL
609-A
601B
603D
601B
L08D
Y1
604-L
603A
601B
609-A
607
Y3-1 Y3-2
622
623A
Y6
623A
Y6
622
622-L 622-R
603E
601B
Y2
L08D
604-R
620
Y6 Y6
620
L21
615
601A-FR
618
Y9
Y8
L08C
Y8
602B
L08C
Y8
602B
Y10
602B
602A
L08C-X
Y7
602A
Y7
603C/616
602A
Y7
L08C
Y7
L08C-X
RIGHT SIDE
L08A-X
623B 623B
FRONT
L08A-X
619
4
GRANDIO
G R E E N H O U S E S
©
ASSEMBLY INSTRUCTION STEPS
STEP ONE: BASE ASSEMBLY
STEP TWO: FRONT ASSEMBLY
STEP THREE: BACK ASSEMBLY
STEP FOUR: MIDDLE ASSEMBLY
STEP FIVE: DOOR ASSEMBLY
5
BASE KIT ASSEMBLY INSTRUCTIONS
**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
W06 must be buried in ground.
W06 must be cut for patio or deck installation
Drill holes in bottom of base to allow for proper fastener to pass through prior to moving forward with assembly. You determine and aquire proper fastener prior to installation.
Outdoor
Ground
Assembly
Base
OR
Deck or
Patio
Assembly
Base
Base
S03/M01
S03/M01
W06
W06
* Must be inserted into the ground, and secured with concrete.
Use: Quikrete fast setting concrete to anchor base.
Pour in Quikrete and water no mixing required.
(Not Included).
GRANDIO
T I P
Make sure base is squared and level before setting anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides.
Base
W06
Base
S03/M01 S03/M01
DECK OR PATIO
INSTALLATION
B
W06
* Must be cut flush with frame.
Use decking screws or concrete anchors to attach base.
(Fasteners not included).
W06 Must Be Modified
Use a Hacksaw or Tinsnip to cut down the length of W06, then install cut side down to level surface.
Base
Base
S03/M01
CUT
S03/M01
W06
6
Save this owner’s manual for future reference and if you need our help.
CONTACT OUR CUSTOMER SERVICE
DEPARTMENT at:
1-866-928-3150
Hours: 8:30a.m.-5:00p.m. Monday through
Friday (Mountain Standard Time)
Backyard Living Source
9543 W. Emerald St., Suite 101
Boise, ID 83704 www.grandiogreenhouses.com
Before you begin take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual, each piece should be labeled with a part number.
Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and opal film side faces inside greenhouse.
Plan out when and where you are going to place the greenhouse, we recommend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA’s, as you may need a permit or documentation before you build.
Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy.
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!
W02
L08D
Y2
604-R
L08A-X
601A-FR
FRONT FRAME ASSEMBLY INSTRUCTIONS
This picture shows the inside view of front section fully assembled.
W02T
601B
W01
603E
Y3-2 Y3-1
W04
603D
601B
W02T
L08D
604-L
Y1
L08A-X
601A-FL
W02
GRANDIO
T I P
We recommend watching our how to assembly videos with tricks and tips for easier assebly and installation of your Grandio Greenhouse at:
www.grandiogreenhouses.com
GRANDIO
T I P
Lay flat on ground to assemble the front frame of your greenhouse. If possible try to find a shady area protected from the wind. Panels can burn grass and plants if in direct light.
GRANDIO
T I P
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
619
7
FRONT FRAME ASSEMBLY
2.1
Use W01 bracket to attach the (2)
601B’s together with the 603E, secure parts with the S05 fasteners provided as shown in . Pre thread all fasteners for ease of installation.
2.2
Insert Y3-1 and Y3-2 window panels as shown in .
2.3
Attach 603E and 603D with W04 and S04/ML01 fasteners as shown in .
2.4
Attach W02T to 601B and 603D with the S04/ML01 fasteners as shown in , leave a bit loose to ease installation of next step.
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
GRANDIO
T I P
Make sure the UV coated side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
601B
S05
601B
W02T
W01
603E
W04
Y3-2
601B
Inside View
W01
603E
Y3-1
S04
ML01
W04
601B
S04/ML01
W02T
603D
603D
603D
601B
W02T
603E
8
FRONT FRAME ASSEMBLY
2.5:
View diagrams and attach the (2)
604‘s and (2) 601A’s to the 619.
shows where the corner pieces attach to 619.
shows where the door frame attaches to the 619.
OUTSIDE
601A-FR
604-R
INSIDE
604-L
OUTSIDE
OUTSIDE
601A-FL
INSIDE
INSIDE
619
INSIDE
OUTSIDE
GRANDIO
T I P
Make sure the small screw hole on the 601A face to the front of greenhouse for future of the
L21 and L28 bracket that holds the door header in place.
GRANDIO
T I P
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
TIP:
If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track.
A
601A-FR
Inside View
ML01
619
604
ML01
S04
INSIDE DOOR FRAME
619
S04
INSIDE
Inside View
9
2.6:
Attach L08D to 604 and 601A using S04/ML01 fasteners as shown in .
2.7:
Attach 606 to 619, this will hold the polycarbonate panels in place.
2.8:
Insert Y1 and Y2 polycarbonate panels into place, make sure Y1 and Y2 slide completely into 606 as show in .
INSIDE
2.9:
Attach W02’s to end of 601B’s, with the S05 screws as shown in .
L08D
FAT END
DOWN
W02
601B
603E
W02T
Y3-2
Y3-1
603D
W02T
601B
Inside View
601A-FR
S05
606
W02
FAT END
DOWN
A
Y2
L08D
604-R
S04/ML01
OUTSIDE
Polycarbonate panel
606
619
619
604-L
606
L08D
3 in.
Y1
601A-FL
601A-FR
Y-2
604-R 604-L
Y-1
601B
601A-FL
W02
FAT END
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
10
2.10:
Move roof and front section together and install all screws and bolts. As shown in and . Tighten W02’s first then tighten the W02T’s second.
2.11:
Attach the L08A-X to 601A and 604. To square front section loosen S04/ML01 attached to the tops of the (2)
L08A-X’s, square the frame with carpenter square or use a measuring tape to make sure corner measurements are the same, tighten L08X’s to hold squareness, L08A-X should be attached 1” up from bottom bolt see .
601B
W02
W02
S05
601A-FR
Inside View
601A-FR
W02T
601B
L08D
Y2
604-R
L08A-X
603E
Y3-2 Y3-1
603D
Use measuring tape to measure from corner to corner to assure square.
601B
W02T
L08D
604-L
Y1
L08A-X
W02
601A-FL
601B
S04
603D
W02T
604-R
601A-FR
S04/ML01
L08A-X
619
GRANDIO
T I P
Set front aside in a shaded area, do not lay on grass, prolonged sunlight through the polycarbonate panels will burn if placed directly on top of plants during the intense sun of the day.
11
BACK ASSEMBLY INSTRUCTIONS
This image shows the inside view of the back wall assembly.
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
GRANDIO
T I P
Make sure the UV coated side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
GRANDIO
T I P
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement.
W02
Inside View
W04-1
601B
L08B
Y2
603B
L08B-X
601A-B
Y5-2
603C
603A
Y4
W01
601B
W04-1
Y5-1
603C
Y4
603B
Y1
L08B-X
W02
601A-B
12
606 L08A 606
BACK CONTINUED
3.1
Use W01 bracket to attach the (2) 601B’s together as shown in diagram .
Attach (2) W02’s to the (2) 601B’s as shown in diagram .
3.2
Attach (2) 601A-B’s to L08A using S04/ML01 fastener as shown in diagram .
Attach (2) 603B’s to L08A using S04/ML01 fasteners as shown in diagram .
Attach 603A to L08A using S04/ML01 fastener as shown in diagram .
W02
601B
601B
S05
W01
W01
601B
Inside View
601B
601B
W02
W02
FAT END
DOWN
601A-B
603B
603A
L08A
603B
601A-B
ML01
S04 INSIDE
601A-B
L08A
13
603B
L08A
INSIDE
603A
L08A
ML01
S04
BACK CONTINUED
3.3
Attach (4) 606’s to L08A as shown in diagram .
Insert the Y4 polycarbonate panels into the grooves of 603B and 603A. Make sure Y4 panels are inserted into 606 as shown in .
Set (2) 603C’s on top of the Y4’s that are now in place. Attach L08B to (2) 601A’s with S04/ML01 fasteners as shown in diagram .
Y5-2
603C
L08B
Attach L08B to (2) 603B and 603A with
S04/ML01 fasteners as shown in and , pre thread all fasteners into assigned channels and align with L08B for ease of installation.
Y4
601A-B
Y2
603B
603A
Attach (2) 603C’s to the L08B using S04/ML01 fasteners.
3.4
Insert the Y5-1 and Y5-2 polycarbonate panels into place. Then insert the Y1 and Y2 into place as shown in the diagram.
L08A
606
Inside View
Y5-1
603C
Y4
601A-B
603C
L08B
603C
603C 603C
L08B
L08B
ML01
S04
603B
603B
L08B
603A
Y1
603B
601A-B
Polycarbonate Panel
L08A
606
14
ATTACHING ROOF TO BACK FRAME
3.5
Attach the roof to the back wall use W01 fastener to 603A and the (2) W02’s to the (2) 601A’s using the S05 fasteners as shown in diagram and , pre thread all screws for easiest installation, tighten when flush with frame and square.
W01
601B
S05
W01
601B
603A
W02
601A-B
L08B
Y2
Y5-2
603C
Y4
603A
Y5-1
603C
Y4
Y1
W02
Inside View
601A-B
601B
W02
FAT END
DOWN
601A-B
L08A
15
3.6
A. Attach the W04-1 to the 603B and 601B with S04/ML01 fasteners as shown in .
B. Attach (2) L08B-X’s to (2) 603B’s and
L08A with S04/ML01 as shown in .
C. Attach (2) L08B-X’s to the (2) 601A’s with fasteners as shown in .
S04/ML01
W04-1
603B
Inside View
L08B-X
603B
L08A
601B
L08B-X
603B
GRANDIO
T I P
Square by loosening bolts attached to the tops of the
L08B-X, use measuring tape to make sure corners to corner measures the same.
16
601A-B
S04/ML01
L08B-X
L08B-X
603B
MIDDLE ASSEMBLY INSTRUCTIONS
4.1
With no less than 2 people place the pre assembled front section on top of the base kit front. Have one person hold the front vertically while the other attaches the front section to the base with
W05/S04/ML01 fasteners as shown in
and . (1) PERSON MUST CONTINUE
HOLDING FRONT FRAME UPRIGHT.
4.2
Attach front to base with W05 clips as shown in .
Warning:
The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports are attached securely to the front and base as shown in step 4.5.
Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.
W05
Inside
C
C
604
Outside
619
Base
Side
W05
GRANDIO
T I P
You will need a minimum of
(2) people to complete the middle assembly of your greenhouse. The more people the merrier at this stage of assembly.
601A
619
Base
Inside View
S04
ML01
W05
Inside
Front
S04
ML01
Base
17
MIDDLE ASSEMBLY CONTINUED
4.3
While the front section is being supported vertically by other person(s) slide in and attach the L08C’s to the front section as shown in . Using tape temporarily attach the loose end of the L08C’s to the base kit as shown in .
Front
Side
L08C
L08C
Tape
Base
L08C
Base
Masking Tape
Side
L08C
W05
Inside View
Base
Front
Inside View
18
MIDDLE ASSEMBLY CONTINUED
4.4
Attach L08C-X to 601A-FR with S04/ML01 on both sides as shown in .
4.5
Attach bottom of L08C-X to L08C, W05, and base as shown in . Repeat steps for other side. The
L08C-X braces will hold the front up vertically without assistance.
4.6
To install the back section repeat steps 4.1 - 4.5.
Remove tape from L08C’s.
W05
L08C-X
Base
L08C
Inside View
L08C-X
601B
601A-B
L08B-X
L08C-X
601A-FR
L08D
L08B-X
L08C-X
L08C
19
MIDDLE ASSEMBLY CONTINUED
4.7
With 2 people, attach the ridge to front and back by sliding into place as shown in and , using S04/ML01 fasteners attach the 607 to the 601B’s.
Side Angle View
607
607
601B
Inside View
601B
Inside View
601B
607
601B
607
601B
20
MIDDLE ASSEMBLY CONTINUED
4.8
Before you attach the 609 you will need to loosen the ML01 (nut) attached to the L08C-X tops. Note: Loosen nuts on only one side at a time, i.e. right front corner, right rear corner.
See .
With 2 people proceed to install 609 in this order, note that 609 must be installed with groove side down see .
1. With one person holding the 609 level and in position have the other person attach the 609 to the 601B using S04/ML01 (nut and bolt).
See .
2. Now move the loosened S04/ML01 (nut and bolt) currently attached to the 601A upward to firmly secure the L08C-X, 609 and 601A together as shown in .
3. Repeat steps 1 and 2 for the other end of 609.
4. With one side firmly secured move to the other side and repeat steps 1, 2 and 3.
Groove
609
LOOSEN
ML01
L08C-X
Inside View
601A
L08D OR
L08B
Profile View
609
L08C-X
609
Inside View
601B
GRANDIO
T I P
Remove only one L08C-X at a time. If all L08C-X’s are removed, the structure will collapse and cause unwarrantable damage.
L08C-X
S04/ML01
L08D OR
L08B
21
MIDDLE ASSEMBLY CONTINUED
4.9
Before you attach the 602A’s to the sides of the greenhouse you will need to loosen the
ML01 (nut) attached to the L08C-X and L08C located at the base. Once the bottom of
L08C-X’s are loosened on one side attach the
602A’s to the sides of the greenhouse in this order.
1. Hold the 602A in place as shown and attach the top of the 602A to the 609 using
S04/ML01 (nut and bolt). As shown in .
2. Now attach the bottom of 602A to the L08C and base using a S04/ML01 (nut and bolt) and
W05 (base clip) as shown in . Note: Where the L08C-X reattaches to the L08C and the
602A be sure to secure them with a W05 (base clip) to the base as shown in .
3. Repeat for the other side.
L08C-X
602A
L08C
Inside View
609
602A
L08C
Base
W05
602A
609
L08C-X
L08C
Inside View
602A
22
W05 CLIP
S04
Inside View
MIDDLE ASSEMBLY CONTINUED
4.10
Attach (2) 602B’s to 609’s and 607 as shown in diagram. Do not attach remaining
602B’s to roof until roof vents are installed.
4.11
Assemble the roof window vents as shown below in and , using the Z02
Screws attach the 615, 616, and 618’s as shown.
602B
609
607
616
618
Z05
SUN
616
PC sheet
615
23
602A
Screwdriver
Z02
Z02
618
616
Z02
Z02
Y10
615
Outside View
Z02
618
ROOF VENT INSTALLATION
4.12
Insert assembled window into the end of ridge and slide into position. See . Window positions are your discretion however, must be in the middle for support, do not place near the front or back. Place directly across from each other for best cross draft ventilation, see for optional placement.
4.13
Attach all remaining
602B’s after roof vents are positioned.
See .
602B
616
SUN
618
615
607
Y9
Y9
602A
Y9
GRANDIO
T I P
Place roof windows in desired location before attaching all 602B’s.
24
INTERIOR ROOF SUPPORT ASSEMBLY
4.14
Attach the BZ1’s to the roof line as shown in diagram with the ML01/S04. Use
CZ1’s to support the interior wall at the eave using the ML01/S04. See diagram .
4.15
Use ML01/S04 to attach the L08C to
601B’s and 602B’s on the inside of roof midway between the roof and the gutters for additional roof support. See diagram .
L08C
BZ1
CZ1
25
4.16
To ensure there is no gap in roof vent position 603C as shown in . Connect
603C to middle of 602B’s using W04 bracket as shown in .
4.17
Attach HQC01 to 616 with the screws see , close roof vent and attach the handle onto HQC02 middle pin (the first two holes of the handle to the first two holes of HQC02). Then attach HQC02 to
603 with Z04 screws, see .
HQC02
Y9
HQC01
HQC01
Z04
616
Inside view of 603C
602B
603C
W04
Y9
616
616
603C
618
603C
Y9
603C
HQC02
HQC01
26
4.16
Install plastic strip 606 before inserting
4.17
After Y7’s are installed, loosen bolts attached to L08C-X in all upper corners. Using a level, adjust
602A and tighten bolts. Repeat in every corner until the greenhouse is level. The top edges of Y7’s will align when greenhouse is level.
609
L08C-X
Loosen
L08C
606
S04/ML01
602A
PC sheet
OUTSIDE
606
L08C
27
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
GRANDIO
T I P
Make sure the UV coated side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
4.20
Insert polycarbonate sheets Y8’s and Y10’s onto the top of your greenhouse. Panels may slide out before gutters are in place. You may want to place a piece of tape on the panel to prevent sliding as shown below once the panels are in place.
Y8
Y8
Y10
Y8
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
GRANDIO
T I P
Make sure the UV coated side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled.
28
4.21
Slide 610 into 609’s groove as shown in diagram . Repeat on both sides. Remove tape after gutter is fully installed. Attach 609
window seals to the inside of roof after all panels and gutters are in place proceed to install both sides of the eave and ridge as shown in and .
Outside View
601B
610
609
601A-FL
Outside
PC Sheet inside
609
609
PC Sheet
607
Outside
Inside
609
PC Sheet
GRANDIO
T I P
Note that there are two parts labeled 609, one is the gutter support, the other is a clip that fits on inside of greenhouse to support polycarbonate panels.
29
Outside View
610
Gutter
609
4.22
Attach end caps to the ridge and gutters on both front and back as shown below.
Squeeze a small amount of rubberized silicone or construction adhesive into the ends of ridge
(607) to secure pressure fit end caps (601).
Adhesive not included. It is recommended to caulk any areas that may allow water penetration such as at the gutter end caps and at the base corners to seal against water as shown in .
J602B-E
J602B-E
Z03
Z03
601
610
J602A-E
Z03
J601
Z03
J602B-E
Z03
J602A-E Z03
30
DOOR ASSEMBLY DIAGRAM
Side View
622
UP
622
Z01
UP
Z01
Bottom
View
622
J08A
Z01
J08A
623B
623A
623A
620
620
623B
Inside View
31
Y6
Y6
Z01
J08A
Z01
622-R
Side View
622-L
UP
Double
Ball Catch
Z01
UP
622
J08A
5.1
Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see , note the J04
Roller is optional, some people prefer not to use the bottom roller.
5.2
Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .
5.3
Insert Y6 windows into position as shown in , make sure to match doors up to each by laying out parts for other door now so window panels face the right direction to the sun, and the locks match up.
623A
623A
623A
Side View
622
UP
622
Z01
620
622
Y6
620
620
Z01
Y6
UP
623B
J08A
Bottom
View
622
J08A
Z01
Inside View
623B
623B
J04
OPTIONAL
GRANDIO
T I P
Transparent Film
Outside Greenhouse
Sun
Polycarbonate
Panel
Opal White Film
Inside Greenhouse
32
5.4
Insert J08A into the bottom of the 622, note the bottom has a groove see .
5.5
Attach the 622 to the 623B, 623A and 620 using the Z01 screws as shown in .
5.6
Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up so doors will latch closed and slide properly .
Side View
Of Top
622-L
* Double
Ball Catch on the 622-L
UP
UP
J08A
* Note the orientation of the 622-L and 622-R.
Also make sure the right side is facing out on the
Y6 polycarbonate panels.
622
622-R
* Double
Ball Catch on the 622-R
UP
Side View
Of Bottom
UP
Bottom
View
J08A
623A
620
Y6
623B
Y6
Z01
622-L
Double
Ball Catch
Z01
Z01
622
Inside View
GRANDIO
T I P
Pay close attention to 622 orientation during assembly. (2) of the (4) 622’s will have holes for attaching handles and a brass double ball catch for the closure of the doors.
33
DOOR ASSEMBLY
5.7
With one person inside greenhouse line up hanging door track with door header, move bolts on
L21 to line up with bolt holes on door header 603B. From the inside attach the S02 nut and bolt set and tighten while holding firmly as high as possible in position from the outside.
S02
34
DOOR INSTALLATION
5.8
Separately slide the top of the doors in the left and right side of L21, see diagram , until they latch in the middle.
5.9
Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown below in , and .
L21
S04 S02
L21
S04
Top
Outside View
Side Profile View of Hanging Track
Bottom
35
622-HNDL
622-HNDL
NUT/BOLT
Inside View
622-HNDL
622-HNDL
NUT/BOLT
DOOR INSTALLATION
5.10
Attach L28 to L21 and 601A as shown below in diagram and . Attach (2) J07 to the ends of L21 see .
5.11
Remove all plastic film from polycarbonate window panels immediately.
603A
S04/ML01
L21
L28
Top View
J07
601A
S02
L28
ML01
S04
601A-FR
36
PICTURE PARTS NO.
GREENHOUSE
MODELS
601A-B
ALL MODELS
DESCRIPTION
601A-FL
ALL MODELS
601A-FR
ALL MODELS
49 1/8”
BACK CORNERS
49 1/8”
FRONT LEFT CORNER
49 1/8”
FRONT RIGHT CORNER
QTY
2
1
1
601B
602A
ALL MODELS
GRA-88
GRA-812
57 1/8”
CORNER ROOF
49 1/8” SIDE
49 1/8” SIDE
4
6
10
602B
GRA-88
GRA-812
57 1/8” ROOF
57 1/8” ROOF
6
10
603A
ALL MODELS
84” BACK
1
603B
ALL MODELS
67” BACK
2
603D
603C
ALL MODELS
47 5/16” FRONT
GRA-88
GRA-812
21 7/8” BACK
21 7/8” BACK
1
4
6
1
603E
604-R
604-L
ALL MODELS
ALL MODELS
ALL MODELS
17” FRONT
65 9/16”
FRONT RIGHT
THEY WILL BE
PACKED TOGETHER
1
1
37
607
L08A
L08B
L08C
L08D
609
610
619
GRA-88
GRA-812
94 5/16” ROOF
142 5/16“ ROOF
ALL MODELS
ALL MODELS
GRA-88
GRA-812
94 5/16” BACK
THEY WILL BE
PACKED TOGETHER
94 5/16” SIDES
142 5/16“ SIDES
ALL MODELS
24 3/16” FRONT
GRA-88
94 5/16“ SIDES
GRA-812
GRA-88
142 5/16” SIDES
2
96 7/16“
SIDE GUTTERS
2
GRA-812
ALL MODELS
142 7/16”
SIDE GUTTERS
2
94 5/16“ FRONT
1
2
2
4
4
1
1
1
1
L08A-X ALL MODELS
43 5/16” FRONT
2
L08B-X ALL MODELS
43 5/16” BACK
2
L08C-X ALL MODELS
54 5/16” SIDES
4
615
616
618
W01
W02
W02T
W04
W04-1
GRA-88
GRA-812
GRA-88
GRA-812
GRA-88
GRA-812
ALL MODELS
22 3/4”
ROOF WINDOW
2
22 3/4“
ROOF WINDOW
4
22 3/4”
ROOF WINDOW
2
22 3/4“
ROOF WINDOW
4
19 9/16”
ROOF WINDOW
4
19 9/16“
ROOF WINDOW
8
FRONT & BACK
2
ALL MODELS
FRONT & BACK
4
ALL MODELS FRONT
2
GRA-88
GRA-812
ALL MODELS
ROOF
ROOF
BACK
5
9
2
W11
Z01
Z02
Z03
ALL MODELS
ALL MODELS
GRA-88
GRA-812
ALL MODELS
#2 PHILLIPS
SCREWDRIVER
4X30
5X12 MM
5X12 MM
3X25 MM
1
13
9
17
4
38
Z04
S02
GRA-88
GRA-812
ALL MODELS
2 Roof Vents
4 Roof Vents
6X20 MM
M6X10
S03/M01
J601
GRA-88
GRA-812
ALL MODELS
M6X10
FRONT & BACK
25
GRA-88
M6X14
122
ML01/S04
S05
GRA-812
M6X14
150
ALL MODELS
PHILLIPS SCREWS
30
2
4
8
4
17
J602A-E ALL MODELS
FRONT & BACK
2
J602B-E
ALL MODELS
FRONT & BACK
2
23”
3
BZ-1
GRA-88
GRA-812
CENTRAL ROOF SUPPORT
5
CZ-1
GRA-88
GRA-812
19 3/8 ” 6
EAVE ROOF SUPPORT
10
HQC01
GRA-88
GRA-812
ROOF
HQC02
L28
W13
ROOF
GRA-88
GRA-812
ROOF
2
ROOF
ALL MODELS 22”
ALL MODELS
10 MM NUT DRIVER
1
4
2
2
4
WINDOW SEAL
14
606
GRA-88
GRA-812
WINDOW SEAL
18
BLACK WINDOW SEAL
609-WS
BASE
W07
W08
W05
ALL MODELS
ALL MODELS
GRA-88
GRA-812
GRA-88
GRA-812
GRA-88
GRA-812
GRA-88
GRA-812
WINDOW SEAL
22
WINDOW SEAL
32
BASE SECTIONS
72”
97”
MID BASE ANCHOR
4
2
4
0
MID BASE ANCHOR
MID BASE
BACK PLATE
MID BASE
BACK PLATE
2
0
2
BASE CLIP
15
BASE CLIP
19
39
Y3-2
Y4
Y5-1
Y5-2
Y6
W06
Y1
Y2
Y3-1
Y7
Y8
Y9
Y10
ALL MODELS CORNER ANCHOR 4
ALL MODELS
FRONT & BACK PANEL
2
ALL MODELS FRONT & BACK
ALL MODELS FRONT PANEL
2
1
ALL MODELS FRONT PANEL 1
ALL MODELS
ALL MODELS
2
1
ALL MODELS
ALL MODELS
GRA-88
GRA-812
BACK PANEL
BACK PANEL
BACK PANEL
DOOR PANEL
SIDE PANEL
SIDE PANEL
1
4
8
12
GRA-88
ROOF PANEL
GRA-812
ROOF PANEL
6
8
GRA-88
GRA-812
GRA-88
GRA-812
ROOF VENT PANEL 2
ROOF VENT PANEL
4
BELOW ROOF VENT
2
BELOW ROOF VENT 4
622-HNDL ALL MODELS
DOOR HANDLES
PACKED TOGETHER
4
622-HNDL
NUT/BOLT
ALL MODELS
620 ALL MODELS
DOOR HANDLES 4
21 7/16” DOOR 2
L21
622
622-L
622-R
623A
ALL MODELS
95 1/2” DOOR
1
ALL MODELS
ALL MODELS
ALL MODELS
64 7/16“ DOOR
ALL PACKED TOGETHER
64 7/16“
LEFT DOOR
64 7/16“
RIGHT DOOR
2
1
1
ALL MODELS
21 1/2” DOOR
2
623B
J04
J07
J08A
ALL MODELS
ALL MODELS
ALL MODELS
ALL MODELS
21 5/16“ DOOR
ROLLERS
OPTIONAL
DOOR
DOOR
2
4
4
2
40
NOTES
NOTES NOTES
Grandio Greenhouse Limited Lifetime Warranty
1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the date of original retail purchase on all plastic panels. Additionally the aluminium frame is warrantied for life. The word “defects” is defined as imperfections that impair the use of the product.
2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, alteration of accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the greenhouse or its components are not covered under this warranty.
4. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use will void this warranty.
5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this product. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
GRANDIO
G R E E N H O U S E S
Model GRA-88-GR & Model GRA-812-GR
GREENHOUSE USER MANUAL
KEEP IN A SAFE PLACE FOR REFERENCE
CONTACT US IF YOU NEED HELP
OR
HAVE MISSING OR DAMAGED PARTS
GRANDIOGREENHOUSES.COM
BACKYARD LIVING SOURCE, INC.
9543 W. EMERALD ST., SUITE 101
BOISE, ID 83704
1-866-928-3150
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project