Directed Electronics 50.7X Installation guide

Directed Electronics 50.7X Installation guide
Responder LC Model 50.7X
Security and Remote Start
Installation Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a person other than a
trained professional may result in severe damage to a vehicle’s electrical
system and components.
© 2008 Directed Electronics, Vista, CA
N5702X 2008-08
Bitwriter®, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost
Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®,
VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics.
The Bitwriter® (p/n 998U)
requires chip version 2.6 or
newer to program this unit.
Bitwriters with a date code of 6a or older require an IC upgrade
(p/n 998M). Some bitwriters with a date code of 6B do not
require the IC upgrade, refer to tech tip # 1112 for more information. Bitwriter 2 compatible.
Contents
Warning! safety first...........................................................................................5
What is included................................................................................................7
Installation points to remember.............................................................................7
Virtual Tach...............................................................................................7
The control center......................................................................................8
Valet® program switch...............................................................................8
Status LED.................................................................................................8
Doubleguard shock sensor..........................................................................9
Before beginning the installation..................................................................9
After the installation...................................................................................9
Component locations and finding wires..............................................................10
Making your wiring connections........................................................................10
Primary harness (H1), 12-pin connector......................................................11
Auxiliary harness (H2), 8-pin connector......................................................11
Heavy gauge remote start, (H3) 10-pin connector........................................12
Remote start input, 5-pin connector............................................................12
Remote start auxiliary output, 5-pin............................................................12
Door lock harness, 3-pin connector............................................................13
Wire connection guides....................................................................................14
Primary harness (H1)................................................................................14
Auxiliary harness (H2) . ................................................................ 18
Heavy Gauge, 10-pin connector................................................................22
Remote start input - 5-pin connector............................................................24
Door lock wire diagrams..........................................................................26
Neutral safety switch interface...........................................................................27
Testing the neutral safety switch.................................................................27
Plug-in LED and valet/program switch.................................................................28
Bitwriter interface - 3-pin black plug...................................................................28
Optional sensor port - 4-pin connector................................................................28
Tachometer settings..........................................................................................29
Virtual tach.............................................................................................29
Tach learning..........................................................................................30
Tach threshold On/Off.............................................................................30
D2D Jumper settings.........................................................................................31
Setting the light flash polarity.............................................................................31
Impact Sensor Adjustment.........................................................................32
Remote control Learn Routine™..........................................................................34
Remote Control Programming....................................................................34
Remote control configuration.............................................................................37
Responder LC 2-way................................................................................37
System features learn routine.............................................................................38
Feature menus.................................................................................................41
Menu 1 - Security....................................................................................41
Menu 2 - Convenience.............................................................................42
Menu 3 - Remote start..............................................................................43
Feature descriptions..........................................................................................44
Menu 1 - Security....................................................................................44
Menu 2 - Convenience.............................................................................47
Menu 3 - Remote start..............................................................................49
Bitwriter®...............................................................................................53
Long term event history.....................................................................................55
Table of zones.................................................................................................56
Shutdown diagnostics.......................................................................................56
Remote starting diagnostics...............................................................................57
Remote start safety check..................................................................................58
Troubleshooting...............................................................................................59
Alarm . ..................................................................................................59
Remote start ...........................................................................................60
Warning! safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed Electronics dealer.
• When properly installed, this system can start the vehicle via a command
signal from the remote control. Therefore, never operate the system in an
area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed Electronics dealers should:
• Never use a test light or logic probe when installing this unit. Always use
a multimeter.
• Never operate the system in an enclosed or partially enclosed area without
ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having
the vehicle serviced, the remote start system must be disabled using the
installed toggle switch. It is the user’s sole responsibility to properly handle
and keep out of reach from children all remote controls to assure that the
system does not unintentionally remote start the vehicle.
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT
THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING
FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL
TIMES.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. Except when performing
the Safety Check outlined in this installation guide, (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user is responsible for having the neutral safety feature
of the vehicle periodically checked, wherein the vehicle must not remotely start
while the car is in gear. This testing should be performed by an authorized
Directed Electronics dealer in accordance with the Safety Check outlined in this
product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.
© 2008 Directed Electronics. All rights reserved.
5
After the remote start module has been installed, test the remote start module
in accordance with the Safety Check outlined in this installation guide. If the
vehicle starts when performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The remote start module must
be removed or properly reinstalled so that the vehicle does not start in gear. All
installations must be performed by an authorized Directed Electronics dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE
USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED ELECTRONICS WILL NOT BE HELD RESPONSIBLE
OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly
installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a
functional, fully engaged parking brake. Do not allow anyone to stand in front
of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top
with a manual transmission. Installation in such vehicles may pose certain risk.
6
© 2008 Directed Electronics. All rights reserved.
What is included
•
•
•
•
•
•
Remote Control 2 way LCD - (p/n 7752X)
Remote Control 1 way companion - (p/n 7652X)
The control module
Control center with integrated status LED and Valet Override switch (p/n
6711T)
Revenger™ Soft Chirp™ six-tone programmable siren
A remote start defeat toggle switch
Installation points to remember
This product is designed for fuel-injected, automatic transmission, or vehicles
with manual transmissions.
Important: The default option “Manual Transmission Mode”
is a safety precaution that forces the installer to enable the
Manual Transmission Start (MTS) routine or program the unit
to the “Automatic Transmission” option before the remote start
can be activated for the first time.
The “Automatic Transmission” option should be programmed on to work with
automatic transmissions. When the “Manual Transmission” option is selected a
specific routine is required before exiting the vehicle to enable the MTS mode.
➢ Virtual Tach
Virtual Tach is a new feature for Directed this year. It is the default RPM-sensing
method for the new Responder LC hybrid security/remote start systems. Virtual
Tach gives the installer the performance of a hardwired tach wire, with the
convenience of voltage sensing. It is far superior to any voltage-sense feature
you’ve tried before.
Virtual Tach monitors the cranking voltage of the vehicle using a very fast microcontroller and an analog-to-digital converter. The microprocessor “saves” the
base voltage as a reference. When Virtual Tach “sees” the slightest uptick in
voltage, indicating that the alternator is charging the battery, the starter motor
shuts off instantly.
© 2008 Directed Electronics. All rights reserved.
7
ENGRAVING RAISED=0.25
➢ D2D
)&&,'(=6'(,
,&
The system has the ability to interface with an XK module through the D2D port.
The advantage to using a D2D interface is that there is less wiring involved in
the installation. Check the XK module installation guide to determine which wires
are not needed, and which options are available.
➢ The control center
The control center position should be discussed with the vehicle’s owner prior to
installation. The LED and Valet switch is housed on the control center, so you may
want to check that the customer is satisfied with the location.
LED
Valet Switch
➢ Valet® program switch
The valet/program switch is built into the control center.
Important: When the vehicle is delivered, please show the
user where this switch is lo­cat­ed and how to disarm the system with %2'<0$7(5,$/+,+($7$%689
it.
olerance please refer specification
f tolerance limits "c"
INJECT TOLERANCE SPEC.
GRADE
IMENSION
UNDER 6
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
Note: An optional valet switch (p/n #8631) is available if the onboard valet
switch is not used for the install.
A
B
C
±
±
±
0.08
0.16
0.30
6~30
0.10
0.20
0.40
30~120
0.20
0.40
0.80
120~300
0.40
0.80
2.00
SCALE
1:
MATE
FINISH
COD
When installing the external valet switch ensure that the location has sufficient
clearance to the rear. The switch should be well hidden. It should be placed so
pas­sen­gers or stored items (such as in a glove box or center console) cannot
accidentally activate it. The switch fits into a 9/32-inch hole.
94I0600
➢ Status LED
The status LED is built into the control center. An optional LED (p/n 8634)
is available if the onboard LED is not used for the install. The LED fits into a
9/32-inch hole.
8
© 2008 Directed Electronics. All rights reserved.
➢ Doubleguard shock sensor
Since the shock sensor is built into the main unit, be sure to keep the shock sensor
performance in mind when deciding on a location for the main unit.
Note: In many vehicles, fastening the main unit (the brain) to a steering column
or screwing it to metal will result in poor sensitivity, especially at the rear of the
vehicle.
➢ Before beginning the installation
•
•
•
•
•
Please read this entire installation guide before beginning the installation.
The installation of this remote start system requires interfacing with many of
the vehicle’s systems. Many new vehicles use low-voltage or multiplexed
systems that can be damaged by low resistance testing devices, such as
test lights and logic probes (computer safe test lights). Test all circuits with a
high quality digital multi-meter before making connections.
Do not disconnect the battery if the vehicle has an anti-theft-coded radio.
If equipped with an air bag, avoid disconnecting the battery if possible.
Many airbag systems display a diagnostic code through their warning
lights after they lose power. Disconnecting the battery requires this code to
be erased, which can require a trip to the dealer.
If using an external LED or Valet Switch, check with the customer about
where to locate the switch.
To avoid accidental battery drainage; turn off the interior lights or remove
the dome light fuse.
Roll down a window to avoid being locked out of the car.
➢ After the installation
•
•
•
Test all functions. The “Using Your System” section of the Owner’s Guide is
very helpful when testing.
When testing, don’t forget that this system is equipped with Nuisance
Prevention® Circuitry (NPC). NPC can bypass trigger zones, making them
appear to stop working. See the Nuisance Prevention® Circuitry section
in the owners guide.
Review and complete the Safety Check section of this guide prior to the
vehicle reassembly.
© 2008 Directed Electronics. All rights reserved.
9
Component locations and finding wires
For detailed information on where to locate components, and how to find the
wires you need, please refer to the Direct Tech web site at www.directechs.
com.
Making your wiring connections
Before making your connections, plan how your wires are to be routed through
the vehicle. For instance, the red 12V constant input and the remote start ignition wires are often routed together to the ignition switch harness. In order to
keep the wiring neat and make it harder to find, you may wish to wrap these
wires together in electrical tape or conceal them in tubing similar to what the
manufacturer used.
There are two acceptable ways of making a wire connection - solder con­nec­
tions and crimp connectors. When properly performed, either type of connection
is reliable and trouble-free. Regardless of whether you solder your connections
or you use mechanical type crimp-on connections, ensure that all connections
are mechanically sound and that they are insulated, especially when connecting
data lines in the vehicle.
Cheap electrical tape, especially when poorly applied, is not a reliable insulator. It often falls off in hot weather. Use good quality electrical tape or heat
shrink.
• Never twist-and-tape the wires together without soldering.
• Never use “fuse taps”, as they can damage fuse box terminals.
If you use tapping connectors such as T-Taps (not to be confused with ScotchLocks), avoid using them in higher-current applications (constant 12V, ground,
etc.) These connectors are inferior in quality and should be avoided.
10
© 2008 Directed Electronics. All rights reserved.
➢ Primary harness (H1), 12-pin connector
H1/1
RED/WHITE
(-) 200mA TRUNK RELEASE OUTPUT
H1/2
RED
(+)12v CONSTANT INPUT
H1/3
BROWN
(+) SIREN OUTPUT
H1/4
WHITE/BROWN
LIGHT FLASH ISOLATION WIRE - PIN 87a of onboard relay
H1/5
BLACK
(-) CHASSIS GROUND
H1/6
VIOLET
(+) DOOR TRIGGER INPUT
H1/7
BLUE
(-) TRUNK PIN/ INSTANT TRIGGER INPUT
H1/8
GREEN
(-) DOOR TRIGGER INPUT
H1/9
BLACK/WHITE
(-) 200mA DOME LIGHT OUTPUT
H1/10
WHITE/BLUE
(-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
H1/11
WHITE
PARKING LIGHT OUTPUT
H1/12
ORANGE
(-) 500mA GROUND WHEN ARMED OUTPUT
➢ Auxiliary harness (H2), 8-pin connector
H2/1
LIGHT GREEN/
BLACK
(-) 200mA FACTORY ALARM DISARM OUTPUT
H2/2
LIGHT GREEN/
WHITE
(-) 200mA FACTORY ALARM ARM OUTPUT
H2/3
WHITE/VIOLET
(-) 200mA AUX 1 OUTPUT
H2/4
VIOLET/BLACK
(-) 200mA AUX 2 OUTPUT
H2/5
WHITE/BLACK
(-) 200mA AUX 3 OUTPUT
H2/6
LIGHT BLUE
(-) 200mA 2ND UNLOCK OUTPUT
H2/7
GRAY/BLACK
(-) DIESEL WAIT TO START INPUT
H2/8
BROWN/BLACK
(-) 200Ma HORN HONK OUTPUT
There are three harness connections relative to remote start function, including
the heavy gauge and input and output harnesses.
© 2008 Directed Electronics. All rights reserved.
11
➢ Heavy gauge remote start, (H3) 10-pin connector
H3/1
PINK
(+) IGNITION 1 INPUT/OUTPUT
H3/2
RED/WHITE
(+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87
H3/3
ORANGE
(+) ACCESSORY OUTPUT
H3/4
VIOLET
(+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL)
H3/5
GREEN
(+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE)
H3/6
RED
(+) FUSED (30A) IGNITION 1 INPUT
H3/7
PINK/WHITE
(+) IGNITION 2 / FLEX RELAY OUTPUT
H3/8
PINK/BLACK
(+) FLEX RELAY INPUT 87A key side (if required) of FLEX
RELAY
H3/9
RED/BLACK
(+) FUSED (30A) ACCESSORY/STARTER INPUT
H3/10
NC (no connection)
NC
➢ Remote start input, 5-pin connector
1
BLACK/WHITE
2
VIOLET/WHITE
TACHOMETER INPUT WIRE
3
BROWN
(+) BRAKE SHUTDOWN INPUT WIRE
(-) NEUTRAL SAFETY SWITCH INPUT
4
GRAY
N/O or N/C (-) HOOD PIN SWITCH INPUT
5
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT
➢ Remote start auxiliary output, 5-pin
1
PINK/WHITE
(-) 200mA FLEX RELAY CONTROL OUTPUT
2
ORANGE
(-) 200mA ACCESSORY OUTPUT
3
VIOLET
(-) 200mA STARTER OUTPUT
4
PINK
(-) 200mA IGNITION 1 OUTPUT
5
BLUE
(-) 200mA STATUS OUTPUT
Note: Wires 1 - 4 on the remote auxiliary outputs are wired to the (-) triggers for
12
© 2008 Directed Electronics. All rights reserved.
the onboard remote start relays and are not diode isolated. If connecting these
wires directly to the vehicle you must place a 1-amp diode in line to prevent
feedback from the vehicle.
➢ Door lock harness, 3-pin connector
1
BLUE
(+) LOCK (-) UNLOCK OUTPUT
2
EMPTY
NOT USED
3
GREEN
(-) LOCK (+) UNLOCK OUTPUT
© 2008 Directed Electronics. All rights reserved.
13
Wire connection guides
➢ Primary harness (H1)
H1/1
RED/WHITE
(-) 200mA TRUNK RELEASE OUTPUT
When the system receives the code controlling trunk release output for longer
than 1.5 seconds, the red/white wire supplies an output as long as the transmission continues. This is typically used to operate a trunk/hatch release or other
relay-driven function.
Warning! Never use this wire to drive anything but
a relay or a low-current input! The transistorized output can only supply 200mA of current. Connecting
directly to a solenoid, motor, or other high-current
device will cause it to fail.
H1/2
RED
(+)12v CONSTANT INPUT
Before connecting this wire, remove the supplied fuse. Connect to the battery
positive terminal or the constant 12V supply to the ignition switch.
Note: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not
use the 15A fuse in the harness for this purpose. This fuse protects the module.
H1/3
BROWN
(+) SIREN OUTPUT
Connect this to the red wire of the siren . Connect the black wire of the siren
to (-) chassis ground, preferably at the same point you connected the control
module's black ground wire.
14
© 2008 Directed Electronics. All rights reserved.
H1/4
WHITE/BROWN
LIGHT FLASH -ISOLATION WIRE - PIN 87a of onboard relay
This wire connects to pin 87a of the onboard light flash relay. It is used whenever light switch isolation on the vehicle is necessary. If the vehicle has a multiplex circuit that needs the light switch isolated, you can remove the onboard
light flash fuse and replace it with the specified resistor (paying attention to the
polarity selection).
Multiplex Lightflash Interface
Lightswitch
Replace fuse with
specified resistor value
Light Flash Fuse
Jumper under door
x
Multiplex
wire in car
White/Brown
x
Cut
White
To control
module in car
H1/5
BLACK
(-) CHASSIS GROUND
We recommend that you do not use a factory ground. Ground all your components to the same point in the vehicle, (preferably the kick panel). Scrape away
any paint and use a factory bolt or make your own ground with a self-tapping
screw and a star washer.
© 2008 Directed Electronics. All rights reserved.
15
H1/6
VIOLET
(+) DOOR TRIGGER INPUT
This wire is used in vehicles that have a positive (+) switched dome light circuit.
Connect the violet wire to a wire that shows (+)12V when any door is opened,
and ground when the door is closed.
H1/7
BLUE
TRUNK PIN / INSTANT TRIGGER INPUT
This input responds to a negative input with an instant trigger.
H1/8
GREEN
(-) DOOR TRIGGER INPUT
Most vehicles use negative door trigger circuits. Connect the green wire to a
wire which shows ground when any door is opened. In vehicles with factory
delays on the dome light circuit, there is usually a wire that is unaffected by the
delay circuitry.
H1/9
BLACK/WHITE
(-) 200mA DOME LIGHT OUTPUT
Connect this wire to the optional dome light supervision relay as shown below:
Important! This output is only intended to drive a relay. It cannot be connected
directly to the dome light circuit, as the output cannot support the current draw
of one or more light bulbs.
16
© 2008 Directed Electronics. All rights reserved.
H1/10
WHITE/BLUE
(-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
This input comes from the factory set to 1 activation pulse. This means that it is
necessary to have a single ground pulse on the white/blue wire for the remote
start to activate or to deactivate.
The H1/10 wire can also be used to activate the Turbo Timer mode when the
car is running and this wire receives a ground.
Note: The number of activation inputs can be programmed to 1 or 2 pulses with
an optional momentary switch. This setting affects both the input wire and the
remote control when operating the remote starter.
To white/blue activation
input on system
H1/11
WHITE
PARKING LIGHT OUTPUT
This wire should be connected to the parking light wire in the vehicle. See Setting the light flash polarity section of this guide for polarity settings.
© 2008 Directed Electronics. All rights reserved.
17
(+) Positive Light Flash Output
WHITE H1/11
(+) LIGHT FLASH OUTPUT
(-) Negative Light Flash Output
WHITE H1/11
(-) LIGHT FLASH OUTPUT
Note: For parking light circuits that draw 10-amps or more, the internal jumper
must be switched to a (-) light flash output. (See Setting the light flash polarity
section of this guide.) P/N 8617 or a standard automotive SPDT relay must be
used on the H1/11 light flash output harness wire.
H1/12
ORANGE
(-) 500mA GROUND WHEN ARMED OUTPUT
This wire supplies a (-)500 mA ground as long as the system is armed. This
output ceases as soon as the system is disarmed. The GWA can be hooked up
to a window module, a voice module or any accessory that requires a ground
when armed.
➢ Auxiliary harness (H2)
H2/1
LIGHT GREEN/BLACK
(-) 200mA FACTORY ALARM DISARM OUTPUT
This wire sends a negative pulse every time the remote start is activated , trunk
release is activated (programmable on/off) or when the doors are unlocked with
the remote. This can be used to pulse the disarm wire of the vehicle’s factory antitheft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown
in the following diagrams.
18
© 2008 Directed Electronics. All rights reserved.
Relay for Negative (-) Disarm Wire
H2/2
LIGHT GREEN/WHITE
Relay for Positive (+) Disarm Wire
(-) 200mA FACTORY ALARM ARM OUTPUT
This wire sends a negative pulse every time the remote start shuts down or when
the doors are locked with the remote. This can be used to pulse the arm wire
of the vehicle’s factory anti-theft device. Use a relay to send a (-) or (+) pulse to
the arm wire.
H2/3
WHITE/VIOLET
(-) 200mA AUX 1 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter buttons controlling Aux 1 channel is pressed. (See descriptions for Aux 3)
Warning! Never use this wire to drive anything
but a relay or a low-current input! This transistorized output can only supply 200 mA. Connecting
directly to a solenoid, motor, or other high-current
device will cause the module to fail.
H2/4
VIOLET/BLACK
(-) 200mA AUX 2 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter buttons controlling Aux 2 channel is pressed. (See descriptions for Aux 3.)
© 2008 Directed Electronics. All rights reserved.
19
Warning! Never use this wire to drive anything but
a relay or a low-current input! This transistorized output can only supply 200 mA. Connecting directly to
a solenoid, motor, or other high-current device will
cause the module to fail.
H2/5
WHITE/BLACK
(-) 200mA AUX 3 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter
button(s) controlling Aux 3 is pressed. This output can be programmed to provide
the following types of outputs
•
•
•
•
Validity: Output that sends a signal as long as the transmission is received.
Latched: Output that sends a signal when the Aux channel button is pressed
and continues until the same button is pressed.
Latched, reset with ignition: Similar to the latched output, this type of output
turns On the first time the Aux channel button is pressed, and turns Off the
next time the same button is pressed. This type of output additionally stops
and resets whenever the ignition is turned On and then Off.
30 seconds timed: The output sends a continuous signal for 30 seconds.
Note: Bitwriter® programs from 1 to 90 seconds.
Warning! Never use this wire to drive anything but
a relay or a low-current input! This transistorized output can only supply 200 mA. Connecting directly to
a solenoid, motor, or other high-current device will
cause the module to fail.
H2/6
LIGHT BLUE
(-) 200mA 2ND UNLOCK OUTPUT
This wire produces a (-) 200mA output for progressive locks in which the driver
door unlocks first and the remaining locks unlock with a second press of the
unlock button on the remote.
20
© 2008 Directed Electronics. All rights reserved.
Note: This feature needs to be programmed “On” to function correctly (see
System Feature Menu #1, feature #8).
H2/7
GRAY/BLACK
(-) DIESEL WAIT TO START INPUT
Connect this wire to the wire in the vehicle that sends the signal to turn on the
WAIT-TO-START bulb in the dashboard. In most diesels the wire is negative
(ground turns on the bulb) and the GRAY/BLACK wire can be directly connected
to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the
bulb) a relay must be used to change the polarity.
The system has a programmable onboard timer (See Feature menu #3, feature
#9) so it is not mandatory to connect to the wait-to-start wire in the vehicle.
Note: A 1-amp diode must be installed in line on the factory wire between the
wait-to-start indicator and the ECM. (See the following diagram for details).
(+)WAIT-TO-START WIRE
© 2008 Directed Electronics. All rights reserved.
21
H2/8
BROWN/BLACK
(-) HORN HONK OUTPUT
This wire is low current output (200mA) and can be hooked to the horn honk
wire in the vehicle. It can be programmed to sound only during full trigger or
to be used like a siren output with arm/disarm honks. Refer to System Features
Menu#1, Feature 10, for more information.
➢ Heavy Gauge, 10-pin connector
There are 9 heavy gauge wires coming from the large 10-pin connector. They
are used to energize the ignition circuits in the vehicle. It is crucial to ensure that
these connections are capable of handling the current demands. For this reason,
Scotch-Locks, T-taps and other such connectors are strongly discouraged.
H3/1
PINK
IGNITION 1 INPUT/OUTPUT
Connect this wire to the ignition wire in the vehicle. This wire not only supplies
voltage for the ignition line in the vehicle, it is also the ignition feed for the
security system.
H3/2
RED/WHITE
(+) (30A) FUSED IGNITION 2 / FLEX RELAY INPUT 87
This wire is the polarity feed for the ignition 2/flex relay.
H3/3
ORANGE
ACCESSORY OUTPUT
Connect this wire to the accessory wire that powers the climate control system.
H3/4
VIOLET
STARTER OUTPUT
This wire hooks up to the starter side of the starter wire in the car. This wire is
also pin 30 of the onboard starter kill relay.
H3/5
GREEN
STARTER INPUT
After cutting the starter wire connect the GREEN wire to the end going to the
ignition switch. This wire is pin 87a of the onboard starter kill relay.
22
© 2008 Directed Electronics. All rights reserved.
H3/6
RED
(+) (30A) FUSED IGNITION 1 RELAY INPUT
This wire is the polarity feed for the Ignition1 relay.
H3/7
PINK/WHITE
(+) IGNITION 2 FLEX RELAY OUTPUT
This wire is factory programmed as Ignition 2 and can be programmed as a
2nd accessory or as a 2nd starter.
H3/8
PINK/BLACK
87a OF IGNITION 2 FLEX RELAY
This wire is used when an ignition switch isolation on the vehicle is necessary
This is common on Toyota and Nissan's which require the use of Tech Tip document #1077. (See Menu #3, Feature #8, for programming options)
H3/9
RED/BLACK
(+) (30A) FUSED ACCESSORY/STARTER RELAY INPUT
This wire is the polarity feed to the accessory and starter relays.
© 2008 Directed Electronics. All rights reserved.
23
➢ Remote start input - 5-pin connector
1
BLACK/WHITE
(-) NEUTRAL SAFETY SWITCH INPUT
Connect this wire to a ground source if installing this unit in an automatic transmission vehicle. If this unit is being installed in a manual transmission vehicle then
connect it to the emergency brake wire. This input MUST rest at ground in order
for the remote start system to operate.
Important! Always perform the steps outlined in Safety Check section to verify
that the vehicle cannot be started in ANY drive gear and that the override switch
is functioning properly.
2
VIOLET/WHITE
TACHOMETER INPUT WIRE
This input provides the module with information about the engine’s revolutions
per minute (RPMs). It can be connected to the uncommon colored wire of the
fuel injector, the crankshaft position sensor, the camshaft position sensor or the
negative side of the coil in vehicles with conventional coils. In multi-coil and high
energy ignition systems locating a proper signal may be more difficult. (See
Finding the Wires You Need section of this guide.) Once connected, you must
teach the system the tach signal.
Note: This wire MUST be used when installing this unit on a manual transmission.
3
BROWN
(+) BRAKE SHUTDOWN WIRE
This wire MUST be connected to the vehicle’s brake light wire. This is the wire
that shows (+) 12V when the brake pedal is depressed. The remote start is
disabled or shuts down any time the brake pedal is depressed. Note: This wire
MUST be used when installing this unit on a manual transmission.
4
GRAY
N/O or N/C (-) HOOD PIN SWITCH INPUT
This wire MUST be connected to a hoodpin switch. This input disables or shuts
down the remote start when the hood is opened. It also triggers the security system if the hood is opened while the system is armed. (See Feature Descriptions,
Menu #1 feature #11 for details about programming.)
24
© 2008 Directed Electronics. All rights reserved.
5
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER
This wire supplies a 200mA output as soon as the module begins the remote
start process. The Blue/White wire can also be used to activate the defogger
trigger (latched/pulsed) 10-seconds after the remote start engages. (See the
Feature Descriptions, Menu#3, feature #11 for details about programming this
output).
➢ Remote start auxiliary output, 5-pin
These signals are provided to drive additional optional relays.
1
PINK/WHITE
(-) 200mA FLEX RELAY CONTROL OUTPUT
This wire is programmed as (-) 2nd ignition output from factory and can be programmed (to drive a relay) as a (-) starter or an accessory output.
2
ORANGE
(-) 200mA ACCESSORY OUTPUT
This wire works like the main accessory wire and can be used (with a relay) to
drive any additional accessory circuits in the vehicle.
3
VIOLET
(-) 200mA STARTER OUTPUT
This wire works like the starter wire and can be used (with a relay) to drive any
additional starter circuits in the vehicle.
4
PINK
(-) 200mA IGNITION 1 OUTPUT
This wire works like the ignition 1 wire and can be used (with a relay) to drive
any additional ignition circuits in the vehicle.
Note: Wires 1 - 4 on the remote start auxiliary outputs are wired to the (-) triggers
for the onboard remote start relays and are not diode isolated. If connecting
these wires directly to the vehicle you must place a 1-amp diode in line to prevent feedback from the vehicle.
© 2008 Directed Electronics. All rights reserved.
25
5
BLUE
(-) 200mA STATUS OUTPUT
This wire supplies an output as soon as the module begins the remote start process. It can be used to activate a bypass module or power the key sense wire
in most vehicles to disarm the factory alarm without unlocking.
Note: Check vehicle information to verify if a bypass module is needed or if the
key sense wire is needed.
➢ Door lock wire diagrams
Important: Depending on the vehicle, the door locks may be controlled by an optional data bus expansion module. If so, no door
lock interface wiring is required.
There are eight different types of door lock systems (Type A - H). The more common type of door lock systems are Type A or Type B. Any other, Types C thru H,
require external relays or a Directed Electronics 451M.
Type A: Three-wire (+) pulse controlling factory lock relays.
Type B: Three-wire (-) pulse controlling factory lock relays.
Type C: Direct-wired reversing-polarity switches. The switches are wired directly
to the motors. This type of system has no factory relays.
Type D: Adding one or more aftermarket actuators. These include central locking
systems without an actuator in the driver’s door, but with factory actuators in all
the other doors.
Type E: Electrically-activated vacuum systems.
Type F: One-wire system - cut to lock, ground to unlock. This is a very rare system
found mainly in early 90’s imports and some newer Hyundai models.
Type G: Positive (+) multiplex. One wire controls lock and unlock using
resistor(s).
Type H: Negative (-) multiplex. Same as Type G system, but uses (-) pulse instead.
Note: You can use a 456L door lock learn module for Type G and H, instead of
relays and resistors. For additional information and wiring diagrams see Document 1041 on www.directechs.com under Resource tab.
26
© 2008 Directed Electronics. All rights reserved.
Neutral safety switch interface
Some vehicles do not have an electrical neutral safety switch. Instead, the vehicle has a mechanical neutral safety switch that physically interrupts the starter
wire and is used when the vehicle is in any drive gear. If the remote start is
interfaced before this switch, it will provide protection from starting in gear.
However, some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechanical part.
Important: You must complete the remote start system installation
before doing the following test. Ensure that the remote start system
is functioning normally. This includes connecting to the brake as
a shut-down.
➢ Testing the neutral safety switch
1.
2.
3.
4.
5.
6.
7.
8.
Make sure there is adequate clearance to the front and rear of the
vehicle because it may move slightly.
Make sure the hood is closed and there are no remote start shut-downs
active.
Set the emergency brake.
Turn the key to the “run” position, this releases the shifter.
Place the car in drive (D).
Place your foot directly over the brake pedal, but do not depress it. Be
ready to step on the brake if the starter engages.
Activate the remote start system.
If the starter engages, immediately depress the brake to shut the remote
start system down. If the starter does not engage, no additional safety
system is required.
If the starter engages and the vehicle is a General Motors product or
Dodge Dakota pickup, refer to www.directechs.com for Document 1008
under the Resource tab. for an alternative shut-down method which
prevents the starter from engaging. If the vehicle is not a General Motors
product or a Dodge Dakota pickup, please call Directed Electronics
Technical Support for an alternative shut-down method. Do not return the
vehicle to the customer until this feature is properly installed!
© 2008 Directed Electronics. All rights reserved.
27
Plug-in LED and valet/program switch
The LED and valet switch are incorporated into the control center, the LED line
plugs into the white 2-pin port and the Valet switch line plugs into the blue 2-pin
port.
Note: Onboard LED and valet switch can be substituted with an optional outboard LED (P/N 8634 for Blue LED and 8633 for red LED) and an outboard
valet switch (P/N 8631).
Bitwriter interface - 3-pin black plug
The black 3-pin port is provided for programming the unit using the Bitwriter
(p/n 998T). When using the Bitwriter, it is possible to configure any and all of
the programmable functions as well as lock the Remote Control and System Features Learn Routines so that unauthorized users cannot change the configuration
or program remote controls to the unit.
When the learn routines have previously been programmed using the
Bitwriter, they may have been locked. Before proceeding with reprogramming the learn routines, they must be unlocked with the Bitwriter
- this cannot be done manually with the Valet switch.
Note: Bitwriters require software v2.6. Bitwriters with a date code of 6a or older
require an IC upgrade (p/n 998M). Some Bitwriters with a date code of 6B
do not require the IC upgrade, refer to tech tip # 1112 for more information.
Bitwriter 2 compatible.
Optional sensor port - 4-pin connector
There is a shock sensor built onboard the main unit. This connector is an optional
sensor port to add sensors to the security system. Optional sensors that may be
used are: 508D Doubleguard Proximity Field Disturbance, 509U Ultrasonic
Sensor, 506T Glass Break Sensor, and 507M Digital Tilt Sensor.
This input can also be used for a second 504D Doubleguard Shock Sensor, or
for additional pin and magnetic switches.
28
© 2008 Directed Electronics. All rights reserved.
Alarm trigger inputs shorter than 0.8 seconds trigger the WarnAway response,
while inputs longer than 0.8 seconds triggers the Full Alarm sequence.
Note: You need to add a 4-pin plug to interface with any hardwired switches
Tachometer settings
➢ Virtual tach
To program Virtual Tach:
1. After the install is complete, remote start the car.
2. If the car does not start on the first attempt, let the remote start attempt
again.
3. Once the car starts, let it run until the parking lights come on.
4. When the parking lights come on, shut off the remote start with the remote
- that's it! Virtual Tach is programmed.
To reset Virtual Tach, go into the remote programming grid and choose option
#4. Virtual Tach cannot be reset with the Bitwriter.
Note: Virtual Tach cannot be used in MTS Manual Transmission Mode.
Virtual Tach handles disengaging the starter motor during remote starting – it
does not address over-rev. If the customer wants to have the over-rev protection
capability, the tach wire must be connected. This may involve more installation
shop charges than initially quoted.
Important: If the Virtual Tach mode over cranks or doesn't
crank the vehicle long enough to start and run the car, use the
Bitwriter to add or subtract the starter output time. You can
adjust the output time in increments of 50mSec of the learned
time using the Bitwriter.
© 2008 Directed Electronics. All rights reserved.
29
➢ Tach learning
REVISIONS
DESCRIPTION
REV.
1
DRN.
DATE
To learn the tach signal:
1. Start the vehicle with the key.
10.44
36.32
2. Within 5 seconds, press and hold the Valet/Program
switch.
11.50
%2'<0$7(5,$/+,+($7$%689
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
C
±
3. After 3 seconds CASE
the P/N:IADGH0A1
LED lights constant when the tach
signal is learned. KEY P/N:IKDEL0A0
UNIT:
SCALE:
DRN BY
M/M
1:1
VICTOR
MATERIAL
0.40
APPD BY
FINISH
0.80
YGF
2.00
CODE
94I0600
DATE
11/20/07
CHK BY
REV.
1
SHEET
NUTEK
TITLE
FELIX
0.30
CORPORATION
DEI
OLED IVU
SIZE DEPT
REVISIONS
A4
OF
DESCRIPTION
DRAWING NO
94I0600
DRN.
REV
DATE0
4. Release the Valet/Program switch.
➢ Tach threshold On/Off
In most cases, this jumper can be left in the Off position. Some new vehicles use
less than 12 volts in their ignition systems. The unit may have trouble learning the
tach signal in these vehicles. Changing the jumper to the On setting changes
the trigger threshold of the digital tach circuit so that it works with these type
vehicles.
36.32
10.44
11.50
CASE P/N:IADGH0A1
KEY P/N:IKDEL0A0
%2'<0$7(5,$/+,+($7$%689
n
C
±
6
0.30
0
0.40
0
0.80
0
2.00
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
MATERIAL
FINISH
CODE
UNIT:
M/M
DRN BY
VICTOR
DATE
11/20/07
CHK BY
CORPORATION
DEI
OLED IVU
APPD BY
SHEET
NUTEK
TITLE
FELIX
YGF
SIZE
OF
A4
DEPT
DRAWING NO
94I0600
REV
0
94I0600
30
© 2008 Directed Electronics. All rights reserved.
D2D Jumper settings
The security system has the ability to work with a compatible module through
the D2D lines. There are two settings: one for using an internal docking module,
(p/n XK 400N) or an external docking XK module.
Jumpers
Jumper settings when using
an onboard D-2-D module
Jumper settings when using
an external D-2-D module
Jumpers
Setting the light flash polarity
Light flash (+) / (-) polarity
The internal fuse is used to determine the light flash output. In the (+) position, the
onboard relay outputs (+)12V on the WHITE wire, H1/11. In the (-) position,
the on-board relay will supply a (-) output. When wiring into a multiplex circuit,
you can replace the fuse with a resistor (paying attention to the polarity setting).
(Refer to diagram on p.16, H1/4 White/ Brown wire description).
Note: For parking light circuits that draw 10 amps or more, the internal jumper
must be switched to a (-) light flash output. P/N 8617 or a standard automotive
SPDT relay must be used on the H1/11 light flash output harness wire.
© 2008 Directed Electronics. All rights reserved.
31
(Light Flash Fuse Jumper is under
access door - use needle nose pliers to
change fuse position)
Access door
➢ Impact Sensor Adjustment
Make sure the keypad is unlocked and the vehicle is disarmed with no open
zones.
• Press and hold the button on the remote for approximately 8 seconds (at
3 seconds ignore the car select indicator) and continue holding.
• The status screen clears and the LCD text displays "main menu". Release the
button and the LCD text changes to the remote setup options table.
• Pressing the
button steps up one Main Menu option per press.
• Pressing the
button steps down one Main Menu option per press.
• When the desired Main Menu option (Sensor Adjust) is displayed on the
LCD text press and hold the button for 1 second, the remote beeps three
times and the siren will emit one long chirp confirming entry into the sensor
adjust mode.
• The LCD text displays the current level setting of the impact sensor.
• Pressing the
button increases the sensitivity up one level and pressing
the
button decreases the sensitivity on level.
• When the desired level is reached, press on the remote to lock in the
setting.
AUX
AUX
AUX
AUX
AUX
AUX
AUX
32
AUX
© 2008 Directed Electronics. All rights reserved.
At this point you can either re-adjust the sensor or press
or
to save and
exit the programming. the siren will emit one long chirp when exiting the adjustment mode.
AUX
AUX
The Impact Sensor Adjustment Mode exits if there is no activity from the remote
after 30 seconds.
Adjusting the impact sensor with the 1way companion remote.
Disarm system
AUX
Press/hold the button of the remote control for 8 seconds or until the Amber
LED turns on and you hear one long beep.
Press/hold the
button 1.5 seconds or until the amber led comes on solid.
The control module emits one long chirp, confirming that it has entered adjustment mode.
,
, or
buttons to adjust the sensor level.
Press the
AUX
AUX
AUX AUX
Arm button: Pressing the
button increases the sensitivity one level. The siren
chirps twice confirming the sensitivity adjustment.
AUX
Disarm button: Pressing the
button decreases the sensitivity one level. The
siren chirps once confirming the sensitivity adjustment.
AUX
Remote Start button: Pressing the
chirps three times.
button resets to default level 7. The siren
AUX
To exit the shock sensor adjustment mode from the remote control:
Press and release the button any time during programming to go back to the
main menu. Press and hold for 1.5 seconds in the main menu to exit programming.
AUX
To exit the shock sensor adjustment mode from the control module:
Open an entry point or turn on the ignition, the control module emits one long
chirp when exiting adjustment mode.
© 2008 Directed Electronics. All rights reserved.
33
Remote control Learn Routine™
The system comes with a 1-way and a 2-way remote control that are already
programmed to the system. The system can store up to 4 different remote control
codes in memory.
The remote uses a Supercode Protocol and requires setup before programming
the system.
➢ Remote Control Programming
2 way programming
1.
2.
Make sure the keypad is unlocked.
Press and hold the
button on the remote for approximately 8 seconds ,
at 3 seconds ignore the car select indicator and continue to hold. The LC
button is released.
text displays Main Menu until the
Release the
button. The LC text displays the remote setup options table.
Pressing the
button steps up one Main Menu option per press and
pressing the
button steps down one Main Menu option per press.
When the Pair Remote menu option is displayed, press and hold the button for 1 second. The remote emits 3 short beeps and the LC text displays
Pair.
Now enter the remote control learn routine using the control center (as
described on the following page) and choose the Auto learn standard
configuration function listed on the program grid.
AUX
AUX
AUX
3.
4.
AUX
AUX
5.
6.
1 way programming:
AUX
Hold the
1.
2.
3.
button on the remote until you hear it emit a long beep.
The transmit LED comes on solid (approximately 8 seconds).
Press and hold the
button and the amber Transmit LED lights up.
Next enter the remote control learn routine and choose the function for
“auto learn configuration” listed on the program grid.
AUX
Note: You do not need to go through the setup for the other features in the
menu.
34
© 2008 Directed Electronics. All rights reserved.
After entering the setup mode on the remotes, use the following learn routine to
add remote controls to the system.
If the siren generates one long chirp when attempting to program the unit, the
learn routine is locked and must be unlocked using the Bitwriter® before proceeding.
The Valet/Program switch, plugged into the blue port, is used for programming.
There is a basic sequence to remember whenever programming this unit: Door,
Key, Choose, Transmit and Release.
REVISIONS
DESCRIPTION
1. Open a door. (The GREEN wire, H1/8, or the VIOLET,
H1/6 must be connected.
REV.
1
DRN.
DATE
2. Insert the key. Turn the ignition to the ON position. The
heavy gauge pink wire must be connected.
10.44
36.32
3. Choose. Within 10 seconds, press and release the
Program switch corresponding to the number of the
desired function step listed in the following table.
11.50
CASE P/N:IADGH0A1
P/N:IKDEL0A0
Once you have selected the function step,KEYpress
the switch once more and hold
NUTEK the selected functional step. Do
it. The LED flashes and the siren chirps to confirm
DEI
not release the Program switch.
%2'<0$7(5,$/+,+($7$%689
C
±
0.30
0.40
0.80
2.00
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
MATERIAL
FINISH
CODE
UNIT:
M/M
DRN BY
VICTOR
DATE
CORPORATION
11/20/07
CHK BY
TITLE
FELIX
OLED IVU
APPD BY
YGF
SHEET
94I0600
SIZE
OF
A4
DEPT
DRAWING NO
94I0600
REV
0
Step
Function
1
Auto Learn Standard Configuration* (default)
The auto learn configuration automatically sets up the remote's button configuration.
Note: Due to the Supercode protocol, you cannot change the configuration.
© 2008 Directed Electronics. All rights reserved.
35
Step
Function
2
Delete remotes: This feature erases all remotes from the memory of the security
system. This is useful in cases when a customer’s remote is lost or stolen.
Note: This does not reset the programmed features of the security system or
reset the Virtual Tach setting.
3
Reset Features: This resets features all of the security system to the factory
default settings.
Note: This feature does not delete the remotes from the security system or reset
the Virtual Tach setting.
4
Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on
the next remote start sequence the unit begins virtual tach initialization.
Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach
setting.
4. Transmit. While holding the Valet/Program switch,
press the
button on the remote control. The unit chirps
to confirm that the code has been successfully programmed. It is not possible to teach a remote control
button to the system more than once.
AUX
REVISIONS
DESCRIPTION
REV.
1
DRN.
DATE
5. Release. Once the code is learned, the Valet/Program
switch can be released. You can advance from one
function step to another by releasing the Valet/Program
switch and tapping it to advance function steps and then
holding it.
Learn Routine is exited if:
• The door is closed
• The ignition is turned off
• The program switch is pressed too many times
• More than 30 seconds elapses between steps
36.32
10.44
11.50
CASE P/N:IADGH0A1
KEY P/N:IKDEL0A0
%2'<0$7(5,$/+,+($7$%689
n
C
±
6
0.30
0
0.40
0
0.80
0
2.00
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
MATERIAL
FINISH
CODE
UNIT:
M/M
DRN BY
VICTOR
DATE
11/20/07
CHK BY
CORPORATION
DEI
OLED IVU
APPD BY
SHEET
NUTEK
TITLE
FELIX
YGF
SIZE
OF
A4
DEPT
DRAWING NO
94I0600
REV
0
94I0600
36
© 2008 Directed Electronics. All rights reserved.
Remote control configuration
➢ Responder LC 2-way
531
,&$
)&&,'(=6
AUX
Note: If Keypad Lock is On, press
and then press
to exit.
AUX
Note: The one-way remote only has a transmit LED and does not report any
confirmations or vehicle requests..
The remote control buttons that operate the features of the security and remote
start system are described below. The buttons operate in this configuration when
the remote control is programmed using the Step 1 Auto-learn routine.
© 2008 Directed Electronics. All rights reserved.
37
For more information about the remote control functions, see the Owners
Guide.
AUX
Level
Button
AUX
AUX
AUX
AUX
AUX
Direct
Access
AUX
x1
AUX
x2
AUX
x3
ARM/LOCK
(Panic)
SILENT ARM
SENSOR
BYPASS
SILENT ALARM
SENSORS
DISARM/UNLOCK (Panic)
SILENT DISARM
VALET ON/OFF
CAR FINDER
STARTER
ON/OFF
RESET RUNTIME
TIMER MODE
ON/OFF
SMART START
ON/OFF
TRUNK
RELEASE (Red/
White)
AUX 1
AUX 2
AUX 3
Advance Level
Change Car
(3s) Enter
programming
(8s)
CABIN
TEMPERATURE
REQUEST
RUNTIME
CHECK
EVENT HISTORY
REPORT
x4
SILENT ALARM
ALL ZONES
DEFOGGER ON
Important: To access “Cabin temperature request, Runtime
AUX
check and event report history, press the
fied amount of times, and then hold.
button the speci-
System features learn routine
The System Features Learn Routine dictates how the unit operates. It is possible to
access and change any of the feature settings using the Valet/program switch.
However, this process can be simplified by using the Bitwriter®. Any of the
settings can be changed and then assigned to one of four remote controls. This
feature is called Owner Recognition. Each time that particular remote control is
used to disarm the system, the assigned feature settings are recalled. Owner
Recognition is only possible when programming the unit via the Bitwriter®.
If programming with the Bitwriter®, the learn routine can be locked or
unlocked. If the learn routine has previously been locked, it must be
unlocked with Bitwriter® - this cannot be done manually with the Valet
switch.
38
© 2008 Directed Electronics. All rights reserved.
n
REV.
1
DRN.
DATE
2. Turn the ignition on, then off. (The heavy gauge PINK
wire must be connected.)
3. Select a Menu. Press and HOLD the Valet/Program
switch. (The Valet/Program switch must be plugged into the
blue port.) After three seconds the siren chirps one-time, indicating entry to the Basic Features Menu. If this is the menu
you want, release the button and go on to
36.32
10.44
11.50
CASE P/N:IADGH0A1
P/N:IKDEL0A0
If the button is not released, the programKEYjumps
to the next menu and the siren
NUTEKSelect the menu you want, then
chirps twice. There are three possible menus.
DEI
release the Valet/Program switch.
%2'<0$7(5,$/+,+($7$%689
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
C
±
0.30
0.40
0.80
2.00
UNIT:
SCALE:
DRN BY
M/M
1:1
VICTOR
MATERIAL
TITLE
OLED IVU
APPD BY
SHEET
CORPORATION
11/20/07
CHK BY
YGF
REV.
1
REV.
94I0600
DATE
FELIX
FINISH
CODE
SIZE
DEPT
DRAWING NO
REV
94I0600
A4
OF
REVISIONS
DESCRIPTION REVISIONS
DESCRIPTION
DRN.
DRN.
0
DATE
DATE
4. Select a Feature. Press and release the Valet/Program
switch the number of times corresponding to the feature
you wish to change. For example, to access the third
feature, press and release 3 times. Then press the button
once more and HOLD it. The siren chirps the number of
times equal to the feature you have accessed.
1
10.44
10.44
36.32
36.32
5. Program the Feature. While holding the Valet/Program
switch, you can toggle the feature on and off using the
remote control. Pressing the button that arms the system
selects the options in increasing order.. Pressing the button
that disarms the system
selects the options in descending
CASE P/N:IADGH0A1
CASE
P/N:IADGH0A1
KEY remote
P/N:IKDEL0A0
order. Pressing the button that activates the
start resets the feature to the
KEY P/N:IKDEL0A0
factory default.
NUTEK
11.50
11.50
%2'<0$7(5,$/+,+($7$%689
C
±
0.30
C
0.40 ±
0
0.800.30
2.000.40
0
0.80
0
2.00
6
REVISIONS
DESCRIPTION
1. Open a door. (The GREEN wire, H1/8, or the VIOLET,
H1/6 must be connected.)
1. Texture is same as
%2'<0$7(5,$/+,+($7$%689
2. Radious
will be if not specified.
Texture
3. 1.
Body
coloris: same as%/$&.
2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
SCALE:
MATERIAL
FINISH
CODE
94I0600
94I0600
UNIT:
M/M
UNIT:
DRN BY
VICTOR
DRN BY
DATE
11/20/07 REVISIONS
DATE
CHK BY
VICTOR DESCRIPTION
11/20/07
1:1 REV. M/M FELIX
MATERIAL
FINISH
1
CHK BY
APPD BY
FELIX
YGF
APPD BY
SHEET
DEI
NUTEK
TITLE
TITLE
SIZE
A4
DEPT
CORPORATION
CORPORATION
DRN.
DATE
OLED
DEI IVU
DRAWING NO
OLED IVU
94I0600
REV
0
6. Release. Valet/program switch.
YGF
CODE
SHEET
© 2008 Directed Electronics. All rights reserved.
10.44
OF
OF
SIZE
A4
DEPT
DRAWING NO
94I0600
REV
0
39
Note: Some features have more than two possible settings. Pressing
toggles through the two-chirp and higher settings.
or
AUX
AUX
Once a feature is programmed:
• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete
To access another feature in the same menu:
1. Press and release the Valet/Program switch the number of times necessary
to advance from the feature you just programmed to the next one you want
to program.
2. Then press the Valet/Program switch once more and hold it.
For example, if you just programmed the third feature in the menu and you want
to program the seventh feature in the menu, press and release the Valet/Program
switch four times and then press it once more and hold it. The siren chirps seven
times to confirm access to the seventh feature.
To select another menu:
1. Press and hold the Valet/Program switch.
2. After three seconds, the unit advances to the next menu and the siren
chirps, indicating which menu has been accessed.
If you just programmed features in the first menu and you want to program a
feature in the third menu, press and hold the Valet/Program switch. After three
seconds the siren chirps twice indicating access to the second menu. Continue
to hold the button and three seconds later the siren chirps three times indicating
access to the third menu.
Features in the third menu are then programmable following steps 4 through 6
of the System Features Learn Routine procedure.
The learn routine exits if any of the following occurs:
• The open door is closed
• The ignition is turned On
• There is no activity for 30 seconds
• The Valet/Program switch is pressed too many times
40
© 2008 Directed Electronics. All rights reserved.
Feature menus
The default settings are indicated in bold type.
➢ Menu 1 - Security
Menu
Item
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
System Arming
Mode
Active
Passive Arm
w/o lock
Passive
Arm w/
lock
Auto re-arm
w/o lock
Auto
re-arm w/
lock
2
Panic Mode
On
Ign Off only
Off
3
Confirmation
Chirps
On w/Warn
chirps On
On w/Warn
chirps Off
Off w/
Warn
chirps On
Off w/
warn
chirps Off
4
Siren duration
30 sec.
60 sec.
5
Ign-controlled
locks
No Ignlocking
Lock &
Unlock
Lock Only
Unlock
Only
6
DoorLock Pulses
Single
Double Unlock Only
Double
Lock Only
Double
Lock &
Unlock
7
Door lock output
duration
0.8 sec.
3.5 sec.
0.4 sec.
8
2nd Unlock
No 2nd
Unlock
2nd unlock
on Igncontrol after
first unlock
2nd unlock
on Igncontrol with
first unlock
9
Comfort Closure
No Comfort
Closure
Comfort
Closure 1
Comfort
Closure 2
10
Horn function
Full Alarm
Only
Siren Function 20 mS
Siren
Function
30 mS
11
Hood Trigger
Type
Normally
Open
Normally
closed
12
Sensor trigger
Single
Double
© 2008 Directed Electronics. All rights reserved.
Siren
Function
40 mS
Siren
function
50 mS
41
➢ Menu 2 - Convenience
Menu
Item
42
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
One-time Bypass
One time
bypass
OFF
One time
bypass
ON
2
Nuisance
Prevention
ON
Off
3
Valet Switch
Pulse Count
1
2
3
4
5
4
Door Trigger
Error Chirp
On
Off
5
Ign-controlled
Dome light
On
Off
6
OEM Alarm
Disarm w/trunk
release
On
Off
7
OEM Alarm
Disarm Output
With
Unlock
Before
Unlock
8
OEM Alarm
Disarm Pulses
1
2
9
Aux 1 Output
type
Validity
Latch
Latch/
reset/ign
Timed 30
sec.
Off
10
Aux 1 Linking
No Linking
Link to Arm
Link to
Disarm
Link to
Arm/
disarm
Link to
Remote Start
only
11
Aux 2 Output
type
Validity
Latch
Latch
reset/ign
Timed 30
sec.
Off
12
Aux 2 Linking
No Linking
Link to Arm
Link to
Disarm
Link to
Arm/
Disarm
Link to
Remote Start
only
13
Aux 3 Output
type
Validity
Latch
Latch
reset/ign
Timed 30
sec.
Off
14
Aux 3 Linking
No Linking
Link to Arm
Link to
Disarm
Link to
Arm/
Disarm
Smart Key
Control (Link
to Remote
Start Off)
Remote
Start Only
© 2008 Directed Electronics. All rights reserved.
➢ Menu 3 - Remote start
Menu
Item
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
1
Transmission
Mode
Manual
Automatic
2
Engine Checking
Mode
Virtual
Tach
Voltage
Off
Tachometer
3
Cranking Time
0.6 sec.
0.8 sec.
1.0 sec.
1.2 sec.
4
Remote Start
Runtime
12 min.
24 min.
60 min.
5
Activation Pulse
Count
1
2
6
Turbo Mode
No Turbo
Mode
On-1 min.
On-3 min.
On-5 min.
7
Timer Mode
Runtime
12 min.
3 min.
6 min.
9 min.
8
Flex Relay
Function
Ignition 2
Accessory 2
Starter 2
9
Diesel Start
Delay
Wait-to
Start input
Timed 15
sec.
Timed 30
sec.
10
Accessory during
Diesel Start
Delay
On
Off
11
Status 2 Output
Status
Latch Rear
Defogger
Pulse Rear
Defogger
12
Parking Light
Output
Constant
Pulsed
Off
13
Anti-grind Output
On
Off
14
Tach Mode
Starter Release
Normal
Increase
15
Vehicle temp
auto report
Off
On
© 2008 Directed Electronics. All rights reserved.
Opt. 5+
1.4
(5)/1.6(6)/
1.8 (7)
2.0(8)4.0(9)
Timed 45
sec.
Decrease
43
Feature descriptions
The features of the system are described below. Features that have additional
settings that can be selected only when programming with the Bitwriter® are
indicated by the following icon:
Note: The numbers in parentheses indicate the number of times the LED on the
antenna flash. Default settings are in bold.
➢ Menu 1 - Security
1-1 Active/Passive Arming: Active arming (1): When active arming is selected,
the system only arms when the transmitter is used.
Passive arming (2): When set to passive arming the system automatically arms
30 seconds after the last door is closed. To alert the user of passive arming, the
siren chirps 20 seconds after the door is closed. This provides the user with an
audible warning prior to the alarm actually arming. At the 30 second mark the
system arms, but without the siren chirp.
Passive arm & lock (3): When set to passive arming and locking, the system
arms the same as described above but also locks the doors at the 30 second
mark.
Auto re-arm w/o lock (4): When the alarm is disarmed from the remote a 30
second timer starts and rearms the alarm.
Auto re-arm w/lock (5): Works the same as above with the addition of locking
the doors when re-arming.
Note: The re-arm feature exits when any hardwired input on the alarm is activated and does not re-engage until the alarm receives a disarm command from
the remote.
.
1-2 Panic On: (1 LED flash) This feature controls whether or not the panic mode
is available with the ignition on. In some states there are laws prohibiting a
siren continually sounding in a moving vehicle. This feature makes the system
compliant with these regulations. The LED flashes twice (2) to indicate Panic with
ignition Off. When the Panic feature is Off, the LED flashes (3)
1-3 Arm/disarm and Warn Away CHIRPS ON: (1) This feature controls the
44
© 2008 Directed Electronics. All rights reserved.
chirps that confirm the arming and disarming of the system, Arm/Disarm chirps
ON, w/Warn Away chirps OFF (2), Arm/disarm chirps OFF, w/ Warn Away
chirps ON (3), Arm/disarm chirps OFF, w/Warn Away chirps OFF (4).
1-4, 30 Second Siren Duration:
It is possible to program the unit to sound
for 30 (1) or 60 (2) seconds during the triggered sequence. Some states have
laws regulating how long a security system can sound.
When using the Bitwriter®, the siren can be programmed to sound for any
length of time from 1 second to 180 seconds.
1-5 Ignition Locks Off: (1) When turned Off the system does not lock/unlock
the doors. (2) Lock and Unlock: The doors lock three seconds after the vehicles
doors are closed when the ignition is turned On, and unlock when the ignition
is turned Off. (3) Lock: Locks the doors three seconds after the ignition is turned
On and the vehicles doors are closed. (4) Unlock: Unlocks the doors when the
ignition is turned off.
1-6 Single Pulse Lock/Unlock(1): The system sends out a single pulse when locking and unlocking. (2) Double-pulse unlock sends out 2 pulses when unlocking.
(3) Double-pulse lock sends out 2 pulses when locking. (4) Double-pulse lock/
unlock sends out 2 pulses when locking and unlocking.
1-7 0.8 sec. Door Lock Pulse Duration (1): The default setting is 0.8 second
door lock pulses. Some European vehicles, such as Mercedes-Benz and Audi,
require longer lock and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5 second (2) pulses, accommodates the door
lock interface in these vehicles. (See door lock connections section for wiring
information regarding Type E door locks interfacing. The 0.4 second (3) pulse
is required on some vehicles where the lock wires can also control the windows
and the 0.8 second pulse causes the windows to open/close when locking or
unlocking.
1-8 No 2nd Unlock Output (1): The second unlock output is defeated at all
times. (2) 2nd unlock On with ignition control, after first unlock turns on the
2nd unlock output and unlocks the passengers doors after the driver’s door is
unlocked with ignition controlled locks. (3) 2nd unlock on with ignition control
with first unlock turns on the 2nd unlock output and unlocks the passengers doors
at the same time the driver door is unlocked with ignition controlled locks.
© 2008 Directed Electronics. All rights reserved.
45
1-9 Comfort Closure Off(1): The system can be programmed to close the windows when the system is locked. If programmed ON, the lock output provides a
20 second pulse when the system is locked. The output is cancelled if the unlock
button is pressed. In the Off setting, the alarm does not perform this function.
(2) Comfort closure 1 - Activates the 20 second timer after the door lock
pulse.
(3) Comfort Closure 2 - Activates the 20 second timer with the door lock
pulse.
To test if the car has the comfort closure:
1.
2.
Insert the key into the drivers door key cylinder.
Turn the key to the lock position and hold for about 10 seconds.
If Comfort closure is available, the windows (and in some cars the sunroof)
closes.
Note: Some cars require that you turn the key once, release it, and then turn and
hold into the lock position.
Important: Comfort closure can only be used on cars that
have the capability of closing the windows (and on some
cars the sunroof as well) with the key cylinder in the door.
1-10 HORN FUNCTION FULL ALARM ONLY (1): SIREN FUNCTION - honk
length 20mS (2) 30mS (3) 40mS (4) 50mS (5). Program for output when the
alarm is fully triggered or as the siren (arming/disarming and Warn Away and
full trigger with timing options).
1-11 Hood Trigger (Normally Open) (1): Hood trigger (normally closed (2).
To program the unit for either a normally open (rests open, or at 12v when the
hood is closed) or a normally closed (rests at ground when the hood is closed)
pin switch.
1-12 Sensor trigger (single) (1) Sensor trigger double (2). When programmed
on; any 2 sensors (zones 2, 4, 7) need to be triggered within 5 seconds of
each other to trigger the alarm. When programmed off; each sensor triggers
the alarm independently.
46
© 2008 Directed Electronics. All rights reserved.
➢ Menu 2 - Convenience
2-1 One time bypass Off (1): One time bypass ON. When programmed On
(2) the unit does not passively arm/lock for one cycle when turning the ignition
On and Off within 3 seconds. When going through this procedure the siren
chirps once indicating that One Time Bypass has been activated.
2-2 Nuisance Prevention® Circuitry (NPC) On (1): Nuisance Prevention Circuity OFF (2). NPC stops repeated triggering of the same zone. If one zone is
triggered three times in one hour, that zone is bypassed for one hour, starting
from the time of the third trigger. During that hour, if the system sees a trigger on
that zone again, the system resets the one hour timer.
If one hour passes and the zone has not triggered again, the zone is activated
and can trigger the system again. NPC only monitors sensor inputs, and does
not bypass the door trigger or the ignition trigger at any time.
If NPC is turned off, the system responds to repeated triggers on the sensor
inputs and will do so indefinitely. Some states have laws regulating how many
times a security system can trigger before it is considered a nuisance and the
vehicle is towed away.
2-3 Disarm from Valet, 1 pulse (1). Disarm from valet, 2-5 pulses (2). The system
can be programmed to count the number of presses of the valet switch before
disarming the security system. The factory default setting is one pulse. The unit
can also be set for two to five pulses.
2-4 Door trigger error chirp On (1): Door trigger error chirp Off (2). This feature
controls the error chirp that is generated if the system is locked with the door
trigger active. This is useful in vehicles with a long dome light delay after the
door is closed. If the system is locked before the dome light turns Off, the system
generates the door trigger error chirp. If this error chirp notification is not desired,
use this feature to disable the door open error chirp notification. If the error chirp
notification is turned Off, no bypass chirp is generated, even if a door is accidentally left open.
2-5 Ignition Controlled Dome Light Supervision On (1): If turned on, the system
turns on the dome light for 60 seconds when the ignition is turned off. The op-
© 2008 Directed Electronics. All rights reserved.
47
tional dome light supervision feature must be installed as described in the Wire
Connection Guide. Ignition controlled dome light Off (2).
2-6 FAD w/trunk release On (1): FAD w/trunk release OFF (2). In the default
setting the factory alarm disarm output disarms the factory alarm system any time
the button controlling the trunk release output is pressed.
2-7 Factory Alarm Disarm/With Unlock (1), Before Unlock (2), Remote Start
Only (3): In the default setting the factory alarm disarm output disarms the factory
alarm system any time the button controlling Unlock or Remote Start is pressed.
The “Before Unlock”(2) output disarms the factory alarm before the unlock
output activates and when remote start is activated. The “Remote Start Only” (3)
disarms the factory alarm only when the remote start is activated.
2-8 FAD 1 pulse (1): FAD 2 pulses (2). This setting determines how many pulses
the security system outputs on the Factory alarm disarm wire.
2-9 Aux 1 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. Timed
(4)
•
•
•
•
•
Validity: Output that sends a signal as long as the transmission is received.
Latched: Output that sends a signal when the Aux 1 button(s) is pressed
and continues until the same button(s) is pressed again.
Latched, reset with ignition: Similar to the latched output this output type
turns ON the first time the Aux 1 button(s) is pressed and turns OFF the next
the same button is pressed. This output type additionally stops and resets
whenever the ignition is turned ON, and then OFF.
30-second timed: Output that sends a continuous signal for 30 seconds.
Off: Output is disabled.
Note: All auxiliary channel timed outputs can be programmed using the Bitwriter® (1-90 seconds)
2-10 Aux 1 Linking, None (1) Lock (2) Unlock (3) Lock/Unlock (4) Remote Start
(5). When programming to Validity or timed output this can be programmed to
activate when locking or unlocking (or remote start) with the transmitter.
2-11 Aux 2 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. Timed,
48
© 2008 Directed Electronics. All rights reserved.
(4) Output, (5) Off: Aux 2 can be programmed for these output configurations.
The unit is set to the default validity output. To change the configuration use the
two-chirp setting to toggle through the different configurations. Refer to feature
2-9 for additional details
.
2-12 Aux 2 Linking None (1) Arm (2) Disarm (3) Arm/Disarm (4) Remote Start
(5). Refer to feature 2-10 for additional details.
2-13 Aux 3 Validity (1) Latched (2), Latch reset w/ignition (3), 30 -sec. Timed,
(4), Off (5): Channel 3 can be programmed for these output configurations.
The unit is set to the default validity output. To change the configuration use the
two-chirp setting to toggle through the different configurations. Refer to feature
2-9 for additional details.
2-14 Aux 3 Linking None (1) Arm (2) Disarm (3) Arm/Disarm (4) Smart key
control (link to remote start Off) (5). When Aux 3 is programmed to Smart Key
control, this wire outputs a 800ms pulse when the Remote Start is shut Off.
The alarm also monitors the door trigger input. When the door is opened during
the remote start runtime, the remote start shuts down and this wire outputs the
800ms pulse.
Note: This wire should be connected to the wire at the push button that start/
stops the car. It pulses the wire at the button to shut off the car when the remote
start is deactivated.
➢ Menu 3 - Remote start
3-1 Manual Transmission Mode (1): Automatic transmission mode (2). In the
default setting the remote start unit is programmed to look for a shutdown procedure to activate the remote start.
3-2 Engine Checking Virtual Tach: (1) When set to “virtual tach” the remote start
monitors the cranking voltage of the vehicle and set that voltage as a reference
point. Fifteen seconds after the crank output sequence the remote start checks the
voltage again to determine if the vehicle is running.
When set to voltage (2), the unit cranks the starter for the programmed time and
then attempts to sense that the engine is running by detecting an increase in volt© 2008 Directed Electronics. All rights reserved.
49
age. If programmed OFF (3) the vehicle cranks for the programmed crank time
(feature 3-3) and does not verify with tach or voltage that the car is running. In
the OFF setting, if the vehicle fails to start, the ignition can stay on for the entire
run duration. When set to Tachometer (4), the unit references the learned tach
signal to disengage the starter. In addition it monitors the RPM and shut down if
the engine RPM is too high or too low.
Note: The tach wire must be connected and programmed for the manual transmission mode to work.
3-3 Crank Time 0.6 (1) 0.8 (2) 1.0 (3) 1.2 (4) 1.4 (5) 1.6 (6) 1.8 (7) 2.0 (8)
4.0 (9) SECONDS: If the unit is programmed for no engine checking or voltage
sense, the crank time must be set to the appropriate duration. The default setting
is 0.6 second and the LED flashes once. If a different crank time is desired,
toggle through the higher settings by using the two-chirp settings.
3-4 Run Time 12 (1), 24 (2) 60 (3) MINUTES:
Selects the time in minutes
that the system operates the engine until the system “times out”. The system may
be shut down using the remote or any of the shutdowns at any time. Using the
Bitwriter®, the run time can be programmed for any duration from 1-60 minutes.
3-5 Activation Pulse One (1): Two activation pulses (2). This allows the system
to use 1 or 2 pulses to activate the remote start sequence.
Note: This setting affects both the input wire and the remote control.
3-6 Turbo Mode: OFF (1). On1 min (2), On 3 min (3) On 5 min (4) On 10
min (5): In the Off setting the turbo mode does not function. In the On and timed
setting, the remote start can be used as a turbo timer. The car remains running
for the programmed runtime, and the ignition is turned Off.
Note: For this feature to work the “turbo timer run time” mode needs to be
programmed ON and the tachometer wire on the remote start needs to be connected and programmed.
3-7 Timer Mode Run Time—12min (1), 3(2), 6 (3), 9 (4) MINUTES:
Selects the time in minutes that the system operates the engine until the system
50
© 2008 Directed Electronics. All rights reserved.
“times out” when the remote start activates in timer mode. The system may be
shut down using a shutdown at any time. Using the Bitwriter®, the run time can
be programmed for any duration from 1-16 minutes.
3-8 Flex Relay Function: Ignition 2 (1) In the factory setting, the flex relay functions the same as the pink ignition 1 wire, in accessory (2) setting the flex relay
functions the same as the Orange accessory 1 wire, in starter (3) setting the flex
relay functions the same as the purple starter 1 wire.
3-9 Diesel Timer—Wait-To-Start Input (1)- 15 (2), 30 (3), or 45 (4) seconds.
Default is the “Wait-to-Start” input control wire, or programmable to ignore
the input control wire by a delay of 15 ,30, or 45 seconds. This feature can
also be optionally programmed with the Bitwriter®, with a delay from 1 to 90
seconds in one second increments.
3-10 Accessory State During Wait-To-Start: On (1) OFF (2): This feature allows
the selection of the accessory output to be ON or OFF during wait-to-start. Use
the two-chirp setting for OFF.
3-11 2nd Status Output: Normal (1) Latched (2) Pulsed (3): This feature allows
selection of status output or a rear defogger mode that turns on ten seconds after
the vehicle has started if the vehicle interior temperature is below 55 degrees F.
The defogger mode has two selections, latched, or pulsed. Latched mode only
stays on for 10 minutes.
Note: When the defogger mode is on, the output is always active and can
be turned on independently with the remote for a one-time activation. (See the
Remote Functions table.)
3-12 Parking Lights: Constant (1) Flashing (2) OFF (3): In the default setting, the
parking lights (if connected) comes on solid during the remote start runtime. In
the two- flash setting the parking lights flashes during the remote start runtime. In
the OFF setting, the parking lights do not come ON or flash, when the vehicle
is remote started.
3-13 Anti-Grind: On (1) OFF (2): With the anti-grind On (default) the ground-
when-armed output is active during remote start operation. This activates the
starter kill relay and prevents the customer from re-cranking the car with the key,
when doing key takeover. If accessories such as a voice module or window
© 2008 Directed Electronics. All rights reserved.
51
module are added to the unit, it may be necessary to use the two-chirp setting
to program this feature OFF.
3-14 Tach Mode Starter Release: Normal (1) Increase (2) Decrease (3): Use the
two-chirp setting to increase time by 15% of the original tach programmed time.
Use the three chirp setting to decrease by 15% of the original programmed
time.
3-15 Vehicle temperature auto report: ON (1) or OFF (2). The default setting is
OFF. When programmed ON the main unit stores the interior temperature of the
vehicle in its temporary memory. When the vehicle’s interior temperature changes 1 degree Celsius, the main unit automatically sends the interior temperature
message to the remote the screen displays the current temperature.
52
© 2008 Directed Electronics. All rights reserved.
➢ Bitwriter®
The Bitwriter®
has the ability to fine tune certain features of the security
system. These features and the adjustments that may be programmed are described in the table below.
Feature
Default
setting
Optional settings
Zone 4 sensor icon
None
Shock/omni, field disturbance, tilt sensor,
glass break, ultrasonic
Aux/trunk icon type
Trunk
Window, sunroof, audio, lights, left slider
dr, right slider dr, rear hatch.
Aux 1 timed output
30 seconds
1-90 seconds
Aux 1icon type
Trunk
Window, sunroof, audio, lights, left slider
dr, right slider dr, rear hatch, timed,
latched, pulsed
Aux 2 timed output
30 seconds
1-90 seconds
Aux 2 icon type
Trunk
Window, sunroof, audio, lights, left slider
dr, right slider dr, rear hatch, timed,
latched, pulsed
Aux 3 timed output
30 seconds
1-90 seconds
Aux 3 icon type
Trunk
Window, sunroof, audio, lights, left slider
dr, right slider dr, rear hatch, timed,
latched, pulsed
Diesel start timer
15 seconds
1-90 seconds
Timer mode run time
12 minutes
1-16 minutes
Timer mode starts
6 starts
1/2/3/4/6/8/10/12/14/16/18
20/22/24 (Starts)
Timer mode intervals
3 hours
1/2/3/4/6/8/10/12/14/16/18/
20/22/24 (Hours)
Smart start low temp
0 (F)
OFF/-20/-10/0/10/20/30/40/50
/60/70 (F)
Smart start high temp
100 (F)
OFF/40/50/60/70/80/90/100/
110/120/130 (F)
© 2008 Directed Electronics. All rights reserved.
53
Feature
Default
setting
Optional settings
Smart start low battery
10.5 volts
OFF/12.5/12/11.5/11/10.5/10/
9.5/9 volts
Sensor 1 level
7 (normal)
0/1/2/3/4/5/6/7/8/9/10/11/1
2/13/14/15
Tach mode starter
release
10 (normal)
0/1/2/3/4/5/6/7/8/9/10/11/1
2/13/14/15/16/17/18/
19/20
Feature programming
Unlocked
Locked
Virtual tach fine tune
Not initialized
0 to 1 second in 50ms increments.
Transmitter programming
Unlocked
Locked
Remote start runtime
12 minutes
1-60 minutes
54
© 2008 Directed Electronics. All rights reserved.
Long term event history
REV.
1
REVISIONS
DESCRIPTION
DRN.
DATE
The system stores the last two full triggers in memory. These are not erasable.
Each time the unit sees a full trigger, the older of the two triggers in memory is
replaced by the new trigger. To access long term event history:
36.32
10.44
1. With the ignition off, press and hold the Valet/Program
switch.
11.50
INJECT TOLERANCE SPEC.
GRADE
A
±
B
C
±
±
UNDER 6
0.08
0.16
0.30
6~30
0.10
0.20
0.40
30~120
0.20
0.40
0.80
120~300
0.40
0.80
2.00
DIMENSION
CASE P/N:IADGH0A1
KEY P/N:IKDEL0A0
REVISIONS
DESCRIPTION
REV.
1
%2'<0$7(5,$/+,+($7$%689
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
*Tolerance please refer specification
of tolerance limits "c"
DRN.
DATE
2. Turn on theNUTEK
ignition.
UNIT:
SCALE:
M/M VICTOR
1:1
MATERIAL
CORPORATION
11/20/07
CHK BY
OLED IVU
APPD BY
YGF
CODE
DEI
TITLE
FELIX
FINISH
94I0600
DATE
DRN BY
SIZE
SHEET
A4
OF
DEPT
DRAWING NO
REVISIONS
DESCRIPTION
REV.
1
REV
94I0600
DRN.
0
DATE
3. Release the Valet/Program switch.
10.44
REVISIONS
DESCRIPTION
4. Press and release the Valet/Program switch within 5
seconds. The LED flashes in groups indicating the last two
zones that triggered the unit for one minute or until the ignition isCASEturned
off. Refer to table of zones.
P/N:IADGH0A1
36.32
REV.
1
DRN.
DATE
10.44
36.32
11.50
KEY P/N:IKDEL0A0
11.50
%2'<0$7(5,$/+,+($7$%689
NUTEK
Note: The Warn Away triggers
are not stored to memory and is not reported.
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
C
±
30
SCALE:
1:1
UNIT:
40
FINISH
80
DATE
DRN BY
M/M VICTOR
MATERIAL
00
CORPORATION
DEI
TITLE
10.44
OLED IVU
APPD BY
YGF
SIZE
SHEET
DEPT
A4
OF
DRAWING NO
P/N:IADGH0A1
0
KEY P/N:IKDEL0A0
94I0600
%2'<0$7(5,$/+,+($7$%689
*Tolerance please refer specification
of tolerance limits "c"
INJECT TOLERANCE SPEC.
GRADE
A
0.20
0.40
0.40
0.80
0.40
0.80
2.00
0.08
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
C
±
0.30
0.10
0.20
UNDER 6
±
B
±
0.16
6~30
30~120
120~300
DIMENSION
REV
CASE
94I0600
36.32
CODE
11/20/07
CHK BY
FELIX
SCALE:
1:1
MATERIAL
FINISH
CODE
UNIT:
DRN BY
M/M VICTOR
DATE
TITLE
11.50
APPD BY
SHEET
NUTEK
11/20/07
CHK BY
FELIX
YGF
SIZE
OF
A4
CORPORATION
DEI
OLED IVU
DEPT
DRAWING NO
REV
94I0600
94I0600
0
CASE P/N:IADGH0A1
KEY P/N:IKDEL0A0
%2'<0$7(5,$/+,+($7$%689
*Tolerance please refer specification
of tolerance limits "c"
INJECT TOLERANCE SPEC.
GRADE
A
C
±
0.30
0.10
0.20
0.40
0.20
0.40
0.80
0.40
0.80
2.00
UNDER 6
±
B
±
0.16
6~30
30~120
120~300
DIMENSION
0.08
1. Texture is same as
2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
MATERIAL
FINISH
CODE
UNIT:
DRN BY
M/M VICTOR
DATE
11/20/07
CHK BY
CORPORATION
DEI
OLED IVU
APPD BY
SHEET
NUTEK
TITLE
FELIX
YGF
SIZE
OF
A4
DEPT
DRAWING NO
94I0600
REV
0
94I0600
© 2008 Directed Electronics. All rights reserved.
55
Table of zones
When using the Diagnostic functions, use the Table of Zones to see which input
has triggered the system. It is also helpful in deciding which input to use when
connecting optional sensors and switches.
Zone No.
Trigger typeInput description
1
Trunk Input
BLUE (H1/7)
2
Shock Sensor
Onboard shock sensor
3
Door Trigger
GREEN (H1/8) and VIOLET (H1/6).
4
Sensor 2 Optional MUX sensor port
5
Ignition
Heavy gauge pink of remote start harness
6
Hood Trigger
GRAY on the 6-pin shutdown harness.
Note: The WarnAway® response does not report on the LED
Shutdown diagnostics
To perform shutdown diagnostics:
1.
2.
3.
4.
With the ignition OFF, press and hold the Valet/Program switch.
Turn the ignition ON and then back OFF while holding the Valet/Program switch.
Release the Valet/Program switch.
Press and release the Valet/Program switch. The LED flashes to report
the last shutdown for one minute or until the ignition is turned on, as
shown in the following table:
LED Flashes
1 flash
2 flashes
3 flashes
4 flashes
5 flashes
6 flashes
56
Shutdown Mode
Runtime expired
Over-rev shutdown
Low or no RPM
Transmitter shutdown (or optional push button)
(+) Brake shutdown
(-) Hood shutdown
© 2008 Directed Electronics. All rights reserved.
7 flashes
8 flashes
9 flashes
10 flashes
11 flashes
*
Timer mode/Turbo mode/Manual mode error *
Neutral safety shutdown
Low battery (voltage mode)
Alarm triggered **
Wait-to-start input timed out
Timer mode error: Ignition is on or shutdown input is active when activating
timer mode.
Turbo mode error: Turbo mode is programmed off, engine is not on or
shutdown input is active.
Manual mode error: MTS mode not enabled.
** Alarm was triggered during remote start sequence.
Remote starting diagnostics
When the remote start function is activated and the 2-way remote emits an error
tone; you have the ability to see what the cause of the no-start situation is by
counting the amount of flashes of the parking lights from the vehicle.
5 flashes
6 flashes
7 flashes
8 flashes
Brake wire is active
Hoodpin wire is active
Manual transmission mode is enabled and not
initialized.
Neutral safety wire has no ground or the neutral safety switch is Off.
© 2008 Directed Electronics. All rights reserved.
57
Remote start safety check
Before vehicle reassembly, the remote system must be checked to ensure safe
and trouble-free operation. The following test procedure must be used to verify
proper installation and operation of the system. The installation must be completed before testing, including connection to the brake switch and hood switch.
1.
2.
3.
Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the
remote start system. Once the engine is running, press the brake pedal.
The engine should shut down immediately. If the engine continues to run,
check the brake circuit connection.
Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the
hood. Activate the remote start system. The vehicle should not start. If the
starter engages, check your hood pin and connections.
Test the NEUTRAL SAFETY shutdown circuit.
Important! Make sure there is adequate clearance to the
front and rear of the vehicle before attempting this test.
1.
2.
3.
4.
5.
6.
Make sure the hood is closed and no other shutdown circuits are active.
Set the emergency brake.
Turn the ignition key to the run position but do not start the engine.
Put the vehicle in Drive (D).
Put your foot over the brake pedal but do not press down on it. Be ready
to step on the brake to shutdown the remote start system.
Activate the remote start system.
•
If the starter engages, immediately step on the brake to shut down the
system. If it does engage, recheck the neutral safety input connection. The
vehicle may use a mechanical neutral safety switch. (See H3/1 BLACK/
WHITE neutral safety switch input in Remote Start Harness Wire Connection Guide section of this guide.)
•
If the starter does not engage, the test is complete. Once the system passes
the tests, the vehicle can be re-assembled and delivered. Do not the use
the remote start system or finalize the installation if it fails any of the safety
check tests.
58
© 2008 Directed Electronics. All rights reserved.
Troubleshooting
➢ Alarm
•
Shock sensor doesn’t trigger the alarm:
•
Door input does not immediately trigger full alarm. Instead,
chirps are heard for the first 3 seconds:
Has the NPC® system been triggered? If so, you hear 5 chirps when disarming.
To check this, turn the ignition key on and off to clear the NPC® memory, and
then retest the shock sensor. For a detailed description of NPC®, see Nuisance
Prevention Circuitry section of the owners guide.
That’s how the progressive two-stage door input works! This is a feature of this
system. This is an instant trigger, remember, even if the door is instantly closed
again, the progression from chirps to constant siren continues.
•
Closing the door triggers the system, but opening the door does
not:
Have you correctly identified the type of door switch system? This happens often
when the wrong door input has been used. (See Door Lock Harness Wire Connection Guide section of this guide.)
•
System does not passively arm until it is remotely armed and then
disarmed:
Are the door inputs connected? Is the H1/6 blue wire connected to the door
trigger wire in the vehicle? Either the H1/5 green or the H1/7 violet should be
used instead. (See wiring diagrams.)
•
Door input does not respond with the progressive trigger, but with
immediate full alarm:
Does the Status LED indicate that the trigger was caused by the shock sensor?
(See Di­ag­nos­tics section of this guide.) The shock sensor, if set to extreme sensitivity, may be detecting the door unlatching before the door switch sends its
signal. Reducing the sensitivity can solve this problem.
•
The Valet/Program switch doesn’t work.
Is it plugged into the correct socket? See Plug-In LED and Valet/Program Switch
© 2008 Directed Electronics. All rights reserved.
59
section of this guide.
•
Status LED doesn’t work.
•
Door locks operate backwards.
Is it plugged in? (See Plug-In LED and Valet/Program Switch section of this
guide.) Is the LED plugged into the correct socket?
This unit has easily-reversed lock/unlock outputs. Recheck wire connections to
see if you have reversed these.
➢ Remote start
•
1.
2.
3.
4.
•
1.
2.
3.
4.
5.
6.
60
The remote start does not activate
Check remote startup diagnostics to determine what may be the cause of
the no start situation.
Check the harnesses and their connections. Make sure that the harnesses
are completely plugged into the remote start module. Make sure there are
good connections to the vehicle wiring.
Check voltage and fuses on the main 12-pin harness and on the
Heavy gauge remote start harness.
The remote start does activate, but the starter never engages.
Check for voltage on the purple starter wire two seconds after the remote
start becomes active. If there is voltage present, skip to Step 4. If there is
not voltage present, advance to Step 2.
Check the 30A fuses.
If the gray/black wait-to-start wire is detecting ground upon activation, the
starter will not crank.
Make sure the purple starter wire is connected on the starter side of the
optional starter kill/anti-grind relay.
Does the vehicle have an immobilizer? Some immobilizer systems do not
allow the vehicle to crank if active.
Check connections. The heavy gauge remote start input wires on the
heavy gauge 10-pin connector should have a solid connection. “T-taps”
or “scotch locks” are not recommended for any high current heavy gauge
wiring.
© 2008 Directed Electronics. All rights reserved.
•
1.
2.
3.
•
1.
2.
3.
The vehicle starts, but immediately dies.
Does the vehicle have an immobilizer? The vehicle’s immobilizer cuts the
fuel and/or spark during unauthorized starting attempts.
Is the remote start programmed for virtual tach or voltage sense? If so, the
crank time may not be set high enough. Voltage sense does not work on
some vehicles.
Check diagnostics. Sometimes a shutdown becomes active during cranking or just after cranking.
The vehicle starts, but the starter keeps running.
Is the system programmed for engine checking off or virtual tach voltage
sense? When programmed for either of these features, the engine cranks
for the preprogrammed crank time regardless of how long it takes for the
vehicle to actually start. Adjust to a lower cranking time.
Was the Tach Learn successful? The LED must light solid and bright to
indicate a successful learn.
Make sure that there is a tach signal at the purple/white tach input wire
of the remote start. If there is not a tach signal, recheck the connection to
the vehicle’s tach wire and make sure the wire is not broken or shorted to
ground leading to the remote start.
•
1.
The vehicle starts, but only runs for 10 seconds.
Is the remote start programmed for voltage sense? If this does not work, a
tach wire should be used.
2. Check shutdown diagnostics.
• The climate control system does not work while the unit is operating the
vehicle.
Either the wrong accessory wire is being energized or more than one ignition
or accessory wire must be energized in order to operate the climate control
system.
• Remote start MTS mode failure
The remote emits a failure notification when trying to enable the manual transmission mode or the vehicle fails to stay remote started when the key is turned off.
Possible causes are:
•
•
Hood Open (gray wire).
Foot Brake active (brown wire).
© 2008 Directed Electronics. All rights reserved.
61
•
•
•
•
62
No Parking Brake input, Black/white neutral safety wire not showing
ground with parking brake set.
Tachometer is not hooked up or programmed.
The unit has not been programmed for tachometer mode
Toggle switch not installed or not in the ON position.
© 2008 Directed Electronics. All rights reserved.
N5702X 2008-08
Vista, CA 92081
www.directed.com
© 2008 Directed Electronics.—All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement