Haier HWM85-9288 User manual

User’s Manual

Fully Automatic Washing Machine

This manual is for

HWM85-9288

Index





Safety precautions

Packing list

............... 2

........................... 4



Names of the parts ............... 4



Installation and

 adjustment............................ 5

Preparation before

 washing................................. 9

Use the operation buttons ....11



Disposal after washing ......... 14



Trouble-shooting Answer

 to question............................15

Specification .........................16





Please read this manual carefully before using.

Retain it for future reference.

2

Safety precautions

Meaning and description of the symbols

WARNING

Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user.

Contents marked with that symbol are actions forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of the user.

FORBIDDEN









Please check if power receptacle has good earthing condition before using to guarantee your safety.

Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.

It is suggested to use foamless washing powder.

Please don’t use the washer in the environment below 0 °C; if the washer has been stored below 0°C, please be sure to ensure the washer is placed under the room temperature more than 2 hours and then use otherwise the washing effects may be lowered or the washer may be damaged.













Please insert the power cord into special receptacle with rated voltage.

Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably. If possible,please adopt electric leakage protector.

The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine.

Do not plug or pull the power plug with wet hand.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.

Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with dry cloth carefully.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.



Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacles loose, do not use the plug any more.



In case the washing machine is installed on ground with carpet, do not block the ventilation hole with carpet. Ensure carpet does not obstruct the opening in the bases.



Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel.





Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning. Wash the clothes that can float on the water surface easily, please be careful especially,for fear damage.

Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children.



Do not put any hot or heavy items (such as the kettle with hot water ) on the washing machine.



Do not wash laundries with volatile materials (such as thinner, petrol etc.)



The children shall not approach the working washing machine.



Keep the machine away from direct sunlight and heat source like the heater.



Do not decompose, repair or alter the machine by yourself.



Do not use water hotter than 50 °C.

Alcohol

3

Packing list

Fully automatic washing machine

Water inlet hose Bottom plate Tapping screws

(One Piece)

User’s manual

Warranty card

4



All illustrations in this Manual are given for reference only. Your products and accessories may show differences from these illustrations due to our continuous improvement.

Installation and adjustment

Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine.

After you open the package, please lean the washing machine gently down on soft items (like the towel cloth, blanket, ect. ).

Install the bottom plate to the bottom of the machine, then lift the machine up gently. See to the figure:

Two claws at the bottom cover shall be inserted in two bar-shaped holes in the stand. Make sure the claws are firmly in place.

Fasten the bottom plate to base frame with one screw

Front

Back

Soft items

Section I enlarging

Bottom plate

The washing machine away from wall should be overrun 20mm. The largest allowable slope of the shank base of the machine is 2°. The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods:



Confirm it's horizontal:

Hang the lead line to check if it is horizontal.



Adjust the adjustable foot:

To twist the adjustable foot, please fi rst lift up the side of the foot slightly, and then you can twist the two adjustable feet. Please make sure to keep the washing machine in balance.

High Low

The adjustable foot

5

NOTE:

The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be reused.

Confirm the water faucet



It is required that the front end shall be longer than 10mm.



The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.

The exit end face of the faucet

Connection between the water inlet hose jointer and the water faucet

water inlet hose jointer

1.

Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component.

See to Figure 1.

Lock lever

Slider water inlet hose

Figure 1

2.

Loosen the screw till the water faucet can be

accessed. Put the jointer of the water inlet

hose on the faucet. See to Figure 2. (If the

faucet is too large and the jointer can not be

set on the water faucet,please loosen the four

screws and take out the bushing in the jointer.

The front end of the faucet must be smooth,

otherwise it may leak water. See to Figure 3.)

Sign plate

Screw

Figure 2

Screw knife

Figure 3

Bushing

6

3.Fasten the four screws evenly. See to Figure 4.

Figure 4

4.Take off the nameplate. Twist the fastening nut

as per the indication of the figure to seal up the

exit end face of the faucet. See to Figure 5.

Remark: Before installation, the threading is

4mm above the upper surface of the nut.After

installation, the threading is 2mm above the

upper surface of the nut.See to Figure 6.

Figure 5

Screw nut

Figure 6

About 4mm before twisting

About less than 2mm after twisting

Connection between the water inlet hose and the washer

1.

Do not take off the water absorption cushion. Please

check if the cushion is dropped or damaged before

each usage. If it happens please contact our

after-sale department immediately.

nut of the water inlet hose

2.Put the nut of the water inlet hose on the valve

jointer.

jointer of the water inlet valve water absorption cushion

3.Fasten the nut. Swing it gently to confirm if it's

suitable.

Connection between the jointer of the water inlet hose and the water inlet hose

1.

Push down the slider. Insert the water inlet hose

into the jointer.

2.

Hang the lock lever to the jointer. Release the

slider till a click sound is heard.

Locking lever

The jointer of the water inlet hose

Slider

Check the connection between the jointer of the water inlet hose and the water faucet

1.

Swing the hose gently to confirm if it is fastened stable.

2.After installation, open the faucet to check if it leaks.

3.Do not bend the hose with overstrain.

4.Before each usage please check if the connection between

the jointer of the water inlet hose and the water faucet, and

the installation of the water inlet hose are firm, so as to

prevent dropping from improper installation position.

Dismantle the water inlet hose

1.

Close the water faucet.

2.Press the locking lever. Push down the slider.Then pull off the water inlet hose.

If the machine is used frequently, the jointer of the water inlet hose can be kept

on the faucet to prevent damaging the fixing screw.

Locking lever

Slider

7

How to change the direction of the drain hose

1.Dismantle the back cover of the washing machine.

2.Press the spring lamination lightly and pull the top

segment of the drain hose decumbent then put

down the drain hose from the drain hose frame.

3.Put down the drain hose, squeeze the drain hose

lightly and take off the hook, put the drain hose into

the cabinet. Take off the small baffle which installed

on the other drain outlet and install it on the side

which won't install the drain hose.

Back cover

Drain hose frame

Spring lamination

4.Extend the drain hose from the other side and install

it on the base by the drain hose frame

5.Install the back cover.

Remark: In order to make sure of the correct of installation, it is suggested to change the

direction of the drain hose with our company serviceman.

The drain hose shall drain smoothly.

1.

The height of the drain hose shall be less than 10cm , or the drainage will not be smooth, and cost such long time that the machine may stop at mid way.

2.

Do not trample or press the drain hose.

3.

If the drain hose is too long, cut it at mid point. To make smooth drainage,cut the front end of the hose slantingly.

4.

If extra drain hose is needed,please make separate purchase.The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m.

8

5.

If the extra hose is too long,cut it either at A or at B point.









Preparation before washing

Connect the water inlet hose. Open the water faucet.

Confi rm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. The earth terminal shall not link to gas pipeline and faucet water pipeline.

Put down the drain hose.

Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally.

Pay attention to followings before washing the laundries

Confirm if there is special requirement for the laundries.

Clear the pocket. Take out the coins,sand, hairpins etc.

Tie the long strips; fasten the buttons;close zippers.

The quantity of the laundries shall not be too large. Stretch and loosen the laundries before putting them in the tub.

When the pulsator is running, the buttons of the laundries may cause noise.

For the sake of discretion, please put the laundries with buttons into other laundries.











Check if the laundries are applicable for washing with machine.

Please repair the damaged cloth before washing in order to avoid the situation worse.

Divide the laundries that are not colorfast from other laundries.

Put those laundries diffi cult to absorb water into water with hand.

For those laundries with heavy soil, please fi rst remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent on them in advance, which can make it easier to remove the soil.







For those laundries that may get lint ball and those with long fur, turn it over before putting in.

Do not put those laundries polluted by chemicals into the washing machine directly.

The foreign materials will result in damage of the machine.

9







The capacity of washing and spinning of he machine refer to the largest weight ofthe standard laundries under dry conditionthat can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity.

The thickness, size, type of the cloth will infl uence the actual washing capacity. It is suitable for one time washing to put in reasonable amount of laundries and the laundries can be turned round in washing.

Do not select the high water level for laundries less than 1.0kg ,so as to avoid splashing of water.

10

How to use the washing powder



Directly dissolved in the machine: (not applicable for fuzzy program )

1

2

3 .

.

.

A

P li d d u

l t s i t m n h t a e h l p e

l q o l u w a n d e t a u n d r ti

.

ir y

R e o s u

f n w

.

S a f o e l t e e

r 3 c

.r

0

t s s u e c o n ti a b l d s e w t o a t d e r i s s o l l e v e v e

.l

i t completely.





The instant dissolving of the washing powder:

1

2

.

.

P

A r e p a d d t r e w a r m h e p o w d e w a t e

r w h li

r e o s

f t

3 ri

0 ir

° n

C g t a o n f d u a ll y c o d i n s t s a o i n l v e e

.r

i .t

The quick program, it is suggested to adopt liquid detergent instead of washing powder to guarantee the washing effect.





Put in the proper quantities detergent according to the water level and the laundries quantities.

It is suggested not to use high sudsing detergent. Washing powder with poor quality or long time storage maybe caked. Please pay attention to cleaning the detergent box in time.

How to use the whitener





Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub.

Avoid using whitener on laundries with color or pattern as they are prone to lose color.







The whitener shall not touch the laundries directly.

Refer to the user’s manual for the usage and quantity of the whitener.

For powder whitener, please dissolve it before using.

13

Use the operation buttons

Description of the function of buttons

overflow

Favourite

Speedy overflow overflow

Favourite,Memory,Standard cycles

4

/Silk

4,6 or 8.

8

0.5h, 1.0h

2.0h

HOLD

Disposal after washing





Please first pull off the power plug from the receptacle before cleaning.

After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine.

Clean the detergent box and set it on the control panel seat.

1

The method of dismantle: Push it up aslant and gently.

2

The method of install : install it upwards and aslant and push it in.

Cleaning the lint filter

1

3

Push down the spring piece of the top lint filter to make the claws out of the filter cover, and then pull out the lint filter to get it down.

Put the lint filter into filter cover, and make it tight .

2

4

Pull the back of the lint filter, and then you can get down it off the front cover of the lint filter.

Sweep the rubbish in the lint filter.

Put the back of the lint filter into the front cover .

Make sure the lint filter well installed, or it can influence your use.





















Notes:

The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet. Please clean it with brush every two months.

If the cabinet is dirty, wipe it with wet cloth

Do not flush it directly with water.

Wipe it with neutral detergent.

Do not wipe it with thinner, petrol, alcohol etc.

After washing, close the water faucet.

Petrol Thinner

Alcoho

( If needed, you can dismantle the water inlet hose).

Do not store water in the washing machine for a long period.

Drain the water completely after each using.

Be sure to pull off the power plug before maintenance.

Hang up the power cord.

Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time ( about 1 hour), then close the top lid.

14

15

Trouble-shooting Answer to question

(If there’s breakdown, please pull off the power plug before checking)

The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair.

If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.

Phenomena

The digitron displays E0.

The reason

●The top lid is opened during

reserve procedure.

How to settle

► Close the top lid.

The drainage cannot work, or is too slow. The digitron displays E1.

●Is the drain hose blocked?

●Is the drain hose put down?

●The top lid is not closed.

► Clean the foreign material. Open and close The top Lid Once.

► Put down the drain hose. Open and

close the top lid once.

► Close the top lid.

It stops running in midway. The digitron displays E2.

The safety switch acts, and the spinning cannot work. The digitron displays E3.

●Are the laundries put slantingly?

●Is the machine slanting?

►

►

Reorder the laundries. Close the top lid.

The machine will start running after 10 seconds of being placed horizontally.

The water filling does not work, or is slow, the digital displays E4.

The digitron displays E6.

The machine does not act

Not wash

●Is the water tap opened, or is

there water supply failure?

●Is the water inlet valve blocked?

●Is the water pressure too low?

●The water level sensor is bad.

►

►

►

Open the water tap. Push the start/

Pause button once.

Clean the water inlet valve then push the start/Pause button once.

Use after the water pressure is normal.

► Please contact the after-sales service department.

●Is there power failure?

●Is the power plug inserted tightly?

●Is the water level reached preset position?

►

►

►

Please use it when there’s power supply.

Insert the power plug tightly.

Fill water to the preset position.

Not spin

There’s abnormal sound inside the machine

The water tap leaks

●Is the power plug inserted tightly?

●Is the top lid closed reliably?

●Are the laundries set flat?

►

►

►

Insert the power plug tightly.

Close the top lid.

Set the laundries flat.

●Is the machine slanting?

●Are the laundries put slantingly in spinning?

●Are there any foreign materials?

●Is the jointer of water inlet hose loose or awry?

► Adjust the machine to be even.

► Reorder the laundries and close the

top lid.

► Remove the foreign materials.

► Fasten the jointer properly.

Phenomena

The spinning is intermittent when it starts.

Push the “spin” button to select “Spin”, but it doesn’t work.

The fi nal spinning is fi nished, it becomes rinsing and begins to inlet water.

There may be some water flowing out of the drain hose in the first use of machine.

Explanation

Balance the laundries to avoid slanting.

The program is setting the drain time. Some time is needed before it starts spinning.

Because the washing clothes lean to one side,the safety switch acts.After water fi lling and running, eliminating the eccentricity of washing clothes,then beginning to spin.

It is the water remained in the factory inspection of performance.

Specifi cation

Rated voltage/Frequency 220-240V ~ /50Hz

Water level / Water quantity (about) 1/20L, 2/29L, 3/38L, 4/46L, 5/54L, 6/60L, 7/65L,8/70L

Injection pressure 0.03 MPa ~ 1.0 MPa

Max Washing/Max Spinning capacity 8.5kg/8.5kg

16