M2000 JK.qxd

USERS MANUAL

M2000

STUDIO EFFECTS PROCESSOR

2

TABLE OF CONTENTS

WELCOME

About this Manual, The help function

THE FRONT PANEL

THE REAR PANEL

Keys, LED’s and other functions explained

Inputs, Outputs

THE SIGNAL FLOW

RECALL

SNAPSHOTS, Recalling a Preset, Combined recall, Factory/User presets, Memory card

STORE

THE WIZARD

I/O MENU

LEVELS MENU

ROUTING

UTIL/MIDI

TEMPO MENU

MIDI MONITOR

Store a new preset, The letterbox, Combined store

I/O, Input selector, Sample Rate, Mix, Primary output

Ranges, Auto level

Serial, Parallel, Dual input, Dual mono, Stereo, Preset glide, Studio setup examples

Display, Preset glide, MIDI in, MIDI out, MIDI map, Security, Memory protect, Backup, Pedal

Tap key, BPM, Tempo subdivisions.

TUNER

EDIT

DYNAMIC MORPHING

THE PROGRAMS

Reverb, Chorus, Flanger, Delay, Phaser, Pitch, EQ, Tremolo, Stereo, Dynamic

THE RESET PAGE

TECHNICAL REFERENCE

TROUBLESHOOTING

MIDI IMPLEMENTATION CHART

Combined Edit, Engine output level

Reset page, User data page

Maybe you will find help here

SELF-TEST PROGRAM

GLOSSARY

PRESET LIST

21

21

22

23

15

16

18

20

10

12

13

14

8

9

5

6

33

34

35

36

24

30

31

32

TC Electronic, Sindalsvej 34, DK-8240 Risskov - [email protected] Rev 4 - SW - V 2.06

3

4

WELCOME

Congratulations on the purchase of your new M2000.

We hope, that you will have as much pleasure using it as we had making it.

The M2000 is basically two separate effect Engines housed in the same box. They can be used as such but they can also work together in a number of Combined configurations. The outputs of the two Engines are mixed down to a common stereo output.

The general Control of the M2000 is accomplished by moving the cursor with the cursor keys; value changes are made by turning the Adjust wheel.

The rest is simple. You select the area that you wish to control by pressing the function keys on the front of the M2000; i.e., if you want to Recall you press the RECALL key.

About this Manual

Many people in the music business have an aversion to reading manuals. We understand that. So if you feel like starting without reading the whole manual, simply: Plug & Play. You can always use the manual for checking out areas that you have questions about or if you want to dig deeper into the unit. Refer to the

Table of Contents for further information.

On the other hand, you might want to know a little more about the M2000 before you start pressing keys. The manual will take you step by step through all of the M2000 functions. If you want to read about a specific function, please refer to the Table of

Contents.

The Help function

The Help function is another way to learn your way around the

M2000. Simply press Help (Shift - I/O) and the Help function will brief you about functions in the current display.

5

THE FRONT PANEL

6

POWER + MEMORY CARD

Electronic power switch

»Easy touch«

Keep pressed for more than

1sec to turn device off.

PC-CARD memory card

Copy presets to/from a standard memory card.

PPM + INDICATORS

PPM meters

range from -40dB to 0dB

Overload

Lights up if internal overload occurs.

SampleRate indicator

48000Hz

44100Hz

32000Hz

Midi In

Midi receive indicator

Card

Indicates presence of a valid memory card

Tempo

Beats per Minute indicator

Morphing

Indicates an on-going morphing

SETUP SECTION

I/O

Input/output

Samplerate

Digital/analog selection

Dithering.

Routing

Setup the internal routing of the 2 engines.

Levels

Input/output analog levels

Digital input level

Util/Midi

Viewing angle

Security lock

Preset handling

Pedal input

MIDI

Secondary functions

Help

(online help function)

Tuner

(the tuner you always wanted)

Auto level

(the fast way to set input levels)

Midi monitor

(Monitors all midi ch. at the same time)

ENGINE 1 OR 2

Recall

Recall presets to engines

Store

Store and name presets.

Edit

Edit engine 1 or 2

Bypass

Individual bypass key for each engine.

Second functions

Recall Wizard

Find a preset that match your application

Delete Preset

The fast (and only) way to delete presets

COMBINED 1+2

Recall

Recall combined presets.

Store

Store and name combined presets

Edit

Engine mix level

Dynamic Morphing

Bypass

Bypasses the entire device.

Snapshots 1-4

Quick store/recall of combined presets


Recall Wizard

Delete Preset

CONTROL SECTION

OK

Confirms operations.

Shift

Enables access to »shifted« secondary functions.

Cursors

Moves between parameters

Adjust wheel

Sets parameter values and preset numbers.


Cancel

Page up/down

7

8

THE REAR PANEL

Main

Power

Switch

Balanced

XLR

Inputs

Balanced

XLR

Outputs

Serial no.

AES/EBU

Digital in/out

S/PDIF

Digital in/out

MIDI

In,Thru,Out

Pedal

Input

Notes:

To accomodate International regulations, we have also added a back panel power switch.

You don’t need to use the power switch on the rear panel. Use the front panel power switch instead.

Remember to use the left input when you’re using only one input.

Pin 2 is »hot« on all XLR’s (AES Regulations).

If You are connecting the M2000 to unbalanced equipment, you must tie pins 1 and 3 together in the cable ends away from the M2000.

We have reserved the two unused pins on the MIDI connectors for an optional RS485 interface. Therefore, if you are connecting M2000 to other equipment that use these pins, please make sure the cable is a 3-wire standard MIDI type, and not a five wire MIDIPLUS type.

If you want to use the pedal input, be sure it is a momentary »make« type.

THE SIGNAL FLOW

Notes Regarding the signal flow:

As shown in the block diagram signals are present on all outputs, all the time.

The digital input gain circuit is capable of »lifting« the signal level. This is a very useful feature if you e.g.

are feeding the M2000 with a DAT recording that isn´t fully leveled to 0 dB.

9

RECALL + SNAPSHOTS

The Recall Displays

The Recall display is the »homepage« of the M2000. This means that you return to this display whenever you exit any other display of the

M2000.

The Recall display is split into two halfs, showing the presets of both Engines at the same time. Engine 1 is always the top half while

Engine 2 is the bottom half of the display.

If you want to have only one effect, use one engine and set the other in bypass mode.

Recall Display Algorithm type Primary parameter Edited flag Preset number

Engine 1

Bank indicator

(RAM/ROM)

Preset name

Engine 2

Primary parameters

Combined Recall Display

Routing mode

Recalling a Preset

Flag indicating change to a new routing (only visible during preset preview)

When you wish to Recall a preset, simply use the

ADJUST wheel to scroll through the presets and press

OK to Recall.

Another way of Recalling is to use the Wizard described later in this section (see »The Wizard«). The Preset number and the OK key will be blinking while you are previewing, indicating that the shown preset is not Recalled yet.

Use the Cursor keys (or the other Recall key) to access the other

Engine.

10

Combined Recall

The M2000 is capable of Recalling Combined presets, meaning a preset for each Engine in a combination.

A Combined preset consists of two normal presets and the

Routing of the M2000: i.e. by Recalling Combined preset 30, a

Chorus will be loaded into Engine 1; a Reverb will be loaded into

Engine 2, and the Routing will change to Serial (see »Routing«).

To Recall a Combined preset

:

Press the Combined Recall key and scroll through the presets using the Adjust wheel. Press OK when you find the right preset.

The Preset number and the OK key will be blinking while you are previewing, indicating that the shown preset is not Recalled yet.

A Combined preset is made out of two normal presets. This means that when you return to the normal Recall display (the

Homepage) the M2000 will display the numbers and names of the two presets that the Combined preset consists of. The Edited flag will light if the presets have been modified.

Factory/User Presets

NORMAL COMBINED

128 ROM

PRESETS

128 ROM

PRESETS

Factory presets

128 RAM

PRESETS

128 RAM

PRESETS

Your own presets

Preset banks

The M2000 contains four different preset banks. Each bank can hold 128 presets.

The four banks are as follows:

Normal ROM bank:

This bank contains 128 normal factory presets. The presets are available from Engine 1 and Engine 2.

Combined ROM bank:

The Combined bank contains 128 Combined factory presets. The presets are available from the Combined Recall.

Normal RAM bank:

This bank can hold up to 128 of your normal presets.

Combined RAM bank:

The Combined Ram bank can hold up to 128 of your Combined presets (see Combined presets).

The two Ram preset banks are located after the corresponding

Rom banks . This means that you scroll through the 128 Rom presets to enter the Ram bank.

For fast RAM access press shift and turn Adjust wheel one click to the right.

Snapshots

The Snapshots are fast Recall keys. Store your favorite presets or use the Snapshots as four compare keys.

A Snapshot will always include both Presets, and Routing just like a Combined preset.

With the Snapshots you are able to switch between completely different configurations with the touch of a single key.

TAKING A SNAPSHOT:

When you want to Take a Snapshot of your M2000 setup, press

Shift and the Snapshot key where you want to store.

RECALLING A SNAPSHOT:

Recall of a Snapshot is very easy as well: Simply press the

Snapshot you wish to Recall and the M2000 will change the whole setup.

11

STORE

Store a new RAM Preset

- Press the STORE button

[Engine 1, 2 or combined]

- Select a location for your new preset

[dial between preset 1 to 128]

- Move cursor to the new name line and dial in the new preset name

[find letter with ADJUST and confirm with OK ]

- Point on DONE and press OK to finalize store operation.

Store with the same name:

If you want to Store the Preset with the existing name simply select the RAM location to Store in by using the ADJUST wheel and press

OK (the OK key will be blinking while you search for a suitable RAM space). The M2000 will now tell you STORED in a pop-up window and return to the homepage.

CAPS LOCK

Indicator

The letterbox

When you want to change the name of the preset to Store, press the Cursor Down key. You are now able to write a new name using the letterbox. Simply dial the ADJUST wheel and press OK to select new letters.

Select CAP, by pressing OK, to change case.

When you have changed the name select DONE in the Letterbox and press OK to Store.

Combined Store

The handling of Combined Store is exactly the same as a normal

Store.

Please note that a Combined Preset Stores the Routing of the

Engines along with the Preset.

Store location

New preset name

Letterbox

Place cursor here and press OK to finalize store operation

Cursor arrows

Using a Memory Card:

When you wish to use a Memory card, simply insert the Card in the M2000. The M2000 will now autodetect your card and the

Store, Recall and Snapshot facilities will be attached to the

Memory card. The M2000 will now use the Memory Card as a normal RAM bank. When you remove your Memory card the

M2000 will switch back to the internal RAM.

If the format of the Memory card is not correct, the M2000 will detect this immediately.

Card types

Type 1 PC-CARDS, with minimum 64KBytes SRAM.

12

THE WIZARD

The Wizard is a tool that helps you find the right preset for your program material.

The Wizard is easy to access and simple to use.

Try it out, and listen what our creative staff suggests for your program material.

The Wizard Display

How to enter »The Wizard«

Engine 1 or 2

1. Select the type of effect you want

2. Which instrument to be used on

3. and the category of intensity

Dial here to select between presets that utilize the search criteria.

Number of presets utilizing the search criteria

Name of selected preset

Press Shift and Wizard to enter the function

Use the parameter keys to select the different filters and the Adjust wheel to select filter parameters.

Set the three different categories as you desire and try out the proposed presets. The Wizard will show the Name and Number of the proposed preset.

Scroll through the Presets using the Adjust wheel and press OK to

Recall.

You can use the Wizard in many different ways, i.e., set it to enter only Drum Reverbs or use it as a creative partner.

Algorithm types

Reverb

Delay

Chorus (including flanging and phasing)

Pitch

Dynamic (compressor/limiting/expanding/deessing)

Misc.

Instruments

Vocals

Guitars

Bass

Keyboards

Percussion

Classic instruments (violins, flutes, etc.)

Category

Gentle

Normal

Extra

13

I/O

Press the I/O key to setup various I/O parameters.

Move the marker using the Cursor keys and turn the ADJUST wheel to change values.

Input Selector

Input Signal

Sample rate:

44100Hz,

48000Hz or from digital inputs

I/O

Press the I/O key to setup various I/O parameters.

Move the marker using the Cursor keys and turn the ADJUST wheel to change values.

Input

Select Input source Analog/Digital.

Select Input type Left/Both. When you select Left the right input will be muted. If you are using two inputs you should select Both

Sample rate

Select Master clock 44.1 kHz/48 kHz/DI.

When Digital Input is selected, the external Clock frequency will be displayed by the three LEDS on the left side of the Display. If the M2000 cannot lock, all three LEDs will be blinking.

Mix

The Mix is a global parameter. When Mix is set to 100% the

Mix parameter of all presets will be 100% and no direct signal will pass through the M2000. Note that when Mix is set to 100% the Bypass keys will act like Mute-keys.

When Mix is set to Mix, the parameter is adjustable.

Here you can freeze mix to 100%

Select Status Bit output:

SP/DIF OR AES/EBU standard.

Indicates the number of bits digital output are dithered to.

Automatically set to default value, when changing Status Bit.

Status Bit:

This selector changes the Channel Status Bits of the digital output between professional and consumer format. When AES is selected, the M2000 will output the professional AES/EBU standard, and when S/PDIF is selected, the M2000 will output the S/PDIF consumer standard.

The defaults setting is AES/EBU but some digital consumer products refuses to accept the professional standard.

In that case change to S/PDIF consumer standard.

Example: If you are using a non-professional DAT machine as a receiver of the M2000 digital output, and you cannot make it accept the digital input, change the output format from AES/EBU to S/PDIF.

NOTE: The different Status Bit standards do not affect the quality of the audio output from the M2000.

Dither:

The M2000 can output Dither from 8 to 22 bit resolution on the

AES/EBU and S/PDIF ouput. The dither type is HP-TDF or High

Pass Triangular probability Density Function.

M2000 uses internal 24 bit resolution and 24 bit AD/DA converters. Dither should therefore only be used when the digital outputs are used (e.g. to a 16 bit DAT machine). It is recommended not to use dither until the final stage of a production, so if there is a chance that the source material is going to be dithered later in a production, do not use Dither.

14

LEVEL MENU

Press the Level key to access this menu.

These global level controls should be set to optimize the performance of the 24bit AD converter in the M2000.

The Level bars can be controlled individually or in common.

Mark the level bar you want to control using the cursor keys, and turn ADJUST to change value.

For common control the marker should be set between the two Level bars.

Note that the Digital In Level is capable of +6 dB gain.

Input gain and sensitivity

(Consumer/PRO)

Output gain and level

(Consumer/PRO)

Digital input gain

Place cursor between L and R to adjust simultaneously

Auto level

Press SHIFT and AUTO LEVEL to activate function.

Ranges

Analog Inputs

Consumer range: -16dB to +10dB

Professional range: -6dB to +16dB

Analog Outputs



Digital Input Level

Adjust the Digital Input from: Off to +6dB.

Send your expected source into the M2000 and press Auto Level

(Shift-Levels) to optimize your Input level automatically. The

M2000 will perform a measure for about five seconds and then adjust the Input level giving you about 6 dB of headroom.

15

ROUTING

Pressing the Routing key gives you the ability to choose one of six different Routings.

Move the marker by pressing the Cursor keys and press OK to accept the new Routing.

A small pop-up window will tell you that the Routing has changed.

Serial

The Serial mode is a Stereo In/Out

Routing. The Serial mode is very useful when you want two independent effects in the same signal path; i.e., from a

Keyboard through the M2000 Reverb and Chorus to The mixer.

Parallel

The Parallel mode is a stereo In/Out

Routing. Both Engines will work as stereo effects and their Output will be mixed down to a stereo signal. With this Routing, the M2000 can be used as two parallel effects on the same stereo source. You may also set the I/O menu to left input to get two independent stereo-out effects on the M2000 from a single send on the mixer.

Dual input (Split mode)

The Dual input mode is a Dual mono In / stereo Out Routing. Left In is always attached to ENGINE 1 and Right In is attached to ENGINE 2. Using this Routing enables you to get two different effects with separated inputs; i.e., connect Aux 1 from your Mixer to Left In and Aux 2 to Right In. You now have access to two separate effects with a common stereo output. Set the individual Preset output volumes to achieve the correct effects balance.

16

Dual Mono

This mode is for Dual Mono In/Out

Routing. Left In/Out is always ENGINE 1 and Right In/Out is ENGINE 2. The Dual

Mono is very useful when you want to use the M2000 as two independent Inserts.

Stereo

When you select the Stereo Routing, the two Engines will link together to perform true Stereo. This means that the preset of

Engine 1 will be copied into Engine 2 and the Edit pages will lock together. The Stereo Routing is indicated by the two Edit LEDS which will be lit simultaneously. Left and

Right channel audio path are completely separated in this

Routing.

Preset Glide

When the Preset Glide Routing is selected, the M2000 will perform preset changes by crossfading the current Effect and the new preset. This gives you a very smooth change of effects; i.e., allowing a Delay to keep repeating while a Chorus is being faded in.

The glide time is located in the Utility menu (see Util/MIDI).

Please note that only one Engine is available while the M2000 is in the Preset Glide Mode.

STUDIO SETUP EXAMPLES

Use two sends on your mixing console

Dual Input mode

Lets say Engine1 is running a long Hall-type reverb and Engine 2 a short more ambient type of reverb. On Your mixing console youll now have individual sends for the two effects.

And - not to forget - you are saving a set of return channels.

Create your own vocal reverb

Serial mode

You probably always wanted to have a long bright reverb on your lead vocal, without

»esses« hanging for seconds. Thats now possible. You simply connect a »deesser« and your favorite reverb in serial. The de'esser will cut away all sharp transients in the signal.

If you want your vocal to have a unique »livingness«, or the reverberated signal to be slightly detuned, simply connect the pitch shifter or chorus in series with the reverb.

There are numerous applications in this mode - try them out.

Two individual inserts on your mixer

Dual mono mode

In the dual mono mode you are able to use two completely separate mono effects at the same time. It can be equalizers or compressors or whatever you can imagine.

Post Production

Stereo mode

When running in stereo mode both engines are linked in stereo and both channels audio path are totally separated. This means that you can process Dolby Surround materials without destroying the hidden information. Use this mode when adding reverb to your recording.

17

18

UTIL/MIDI

How to move around

In the Util/MIDI menu you always move by pressing the

Cursor keys and change values by dialing the Adjust wheel.

Display

Viewing Angle:

Adjust for best contrast on the LCD display.

Preset glide:

Glide time

This parameter sets the glide time of the incoming preset. The parameter is only active when Preset glide Routing is selected

(See Routing).

In the MIDI section you are able to see the MIDI setup of both Engine 1, Engine 2 and the Combined section at the same time.

MIDI In

Channel

Sets the Channel of which the current Engine will respond to.

When set to Omni the Engine will respond to all channels, When set to off no MIDI will be received.

Filter

Sets whether the current section of the M2000 should respond to

MIDI Control changes (CTRL) and MIDI Program changes

(PROG) or not; i.e., when Filter is set to PROG the M2000 will only respond to MIDI Program changes.

Offset

With this parameter, you are able to add or subtract to the incoming Program change; i.e., the incoming Program Change is preset

123, and the Offset is set to +1, the Program Change will now be

124.

Sys-ex id

Sets the Sys-Ex ID number of the M2000.

MIDI Out

Channel

Sets the sending MIDI channel of the M2000.

Filter

Sets wether the current section of the M2000 should send out

MIDI Control changes (CTRL) and MIDI Program changes

(PROG) or not; i.e., when Filter is set to PROG the M2000 will only send out MIDI Program changes.

Offset

With this parameter you are able to add or subtract to the outgoing Program change; i.e., the outgoing Program Change is preset 123, and the Offset is set to +1 the Program Change will now be 124.

MIDI Map

MIDI Map

Sets the current MIDI Map On or Off.

Prg. Bank

Determines which Bank the MIDI Map should control;

Ram/Rom.

Prg. In

The current Program change Maps to a M2000 program (See

Maps to).

Maps to

The current incoming Program change set in Prg. In will be changed to the Program number of this parameter.

Reset Map

Press OK while this parameter is selected and your MIDI Map will be Reset.

Security

Security Lock

Press OK while this parameter is selected to Security lock the

M2000. When locked, you will have to dial the PIN-Code shown below to access the M2000.

PIN-Code

Set your own PIN-code for the Security lock by Dialing the

Adjust Wheel.

If you should forget your PIN-code, please enter the Reset page.

This will release M2000 from the locked state. (You do not have to run any of the reset functions).

Memory Protect

Protect

This parameter sets the Memory protect On or Off. When the

Protect is activated the Ram presets inside the High and Low limit are write protected.

Low Lim

Sets the Low limit of the Memory protect. The current number is included in the Protect.

High Lim

Sets the High limit of the Memory protect. The current number is included in the Protect.

Snapshot Protect

Enables or disables the Protect of the Snapshots. When activated the Snapshots are write protected.

Memory Backup

Mem > Card

Insert a PC-CARD Card in the card-slot and press OK. All Ram presets of the M2000 will now be backed up to the Memory

Card.

Card > Mem

Insert the PC-CARD Card containing your presets and press OK.

All Presets will now be Stored back into the M2000 Ram.

Warning:

This action will destroy ALL existing Ram Presets of the M2000.

Mem > Midi

Connect your M2000s Midi Out to a another M2000, a

Sequencer or any other Midi Recordable device. Press OK and the M2000 will perform a Midi bulk dump of all Ram Presets.

Midi > Mem

Connect the Storing device to the M2000s Midi In and press OK.

The M2000 is now ready to receive a Midi bulk dump containing

Ram presets. WARNING this action will destroy ALL existing

Ram Presets of the M2000.

Pedal

Pedal

The Pedal input can control any one of four different features:

Engine 1 Bypass, Engine 2 Bypass, Engine 1+2 Bypass and Tap tempo.

Select by turning the Adjust Wheel.

19

TEMPO

Tapped or dialed BPM

Which engine to work on

Define subdivision beat

Tapped time in ms.

Tapped time in ms.

corrected with the subdivision factor.

Tap Tempo

The Tap Tempo key is similar to its cousin Learn on the TC

2290 Digital Delay. Only the M2000 Tap Tempo key can control various parameters: Delay time, Decay time, Chorus speed, etc.

When you press the Tap key, a Tempo menu pops up. If no further actions are made, the Tempo menu will disappear after a few seconds.

The Tap key is attached to a default parameter in each effect type.

This means that the function of the Tap key changes along with the presets (See default list later in this section).

The Tempo Menu

The Tempo you tap is always measured in BPM (Beats Per

Minute). The Tempo menu is able to recalculate the tapped time into Subdivisions of the BPM. Simply set the Tempo menu to the

Subdivision you like and Tap the BPM on the Tap Tempo key.

You also have the possibility of changing the Tempo using the

BPM parameter in the Tempo menu. When a preset has been

Tapped, the parameter attached to the Tap function will be displayed in BPM in the Tempo Menu.

Tempo BPM

The BPM will display the Tapped tempo (BPM is equal to the 1/4

Subdivision). You can also set your Tempo with this parameter using the ADJUST wheel.

Subdivision

Sets the subdivision of the Tempo. If the Subdivision is set to 1/8, the actual Tempo will be twice as fast as the tapped time, etc. The following subdivisions are possible:

1,1/2,1/4,1/4T,1/8,1/8T,1/16,1/16T,1/32,1/32T (T for triplets).

20

Tap/Subdivision

This is read only parameters displaying the tapped time and the

Subdivided time in milliseconds. Tap Time Subdivision is corresponding to the parameter in your preset.

The parameters controlled by the Tap key

Reverb Decay parameter

Delay Delay time

Chorus Speed

Flanger Speed

Phaser Speed

Tremolo Speed

Panner Speed

Press and hold TAP for 3 seconds to learn MIDI tempo (MIDI-Clock).

MIDI MONITOR & TUNER

»MIDI MONITOR SCREEN«

Program changes

Note on/off

Controllers

System exclusive

Engines MIDI channels

Channel pointer

»TUNER SCREEN«

Tuning guide

Select guitar/bass or note set manual

Master tune 440-445Hz

MIDI Monitor

Press Shift - Util/Midi to access MIDI Monitor.

In the MIDI Monitor, you are able to see all MIDI actions received by the M2000. The actions are displayed according to the current channels.

Prog.

Note

Displays Program changes.

Displays Note On/Off.

Cntl Displays Control changes

Sys-x Displays System exclusive commands

Eng

Chan

Displays the midi channels of Eng 1,2 and combined.

Displays the Midi channels

Press any key to exit MIDI Monitor.

Deviation in cents

Tuning guide

Detected note

Tuner

Press Shift - Routing to access the Tuner of the M2000.

When Tuner is selected, the Outputs will be muted.

Select Guitar/Bass/Manual mode by turning the ADJUST wheel.

When Guitar or Bass is selected, the Tuner will only respond to notes corresponding to the strings of these instruments.

When set to Manual, you must select the desired Note using the

ADJUST wheel.

In the Master section, you can Calibrate the Tuners default, 440-

445 Hz.

The detected note will be shown in the lower right corner and in the note line. When the horizontal marker is 0, you are tuned in.

The two tuning guides will tell you wether the note is too flat or too sharp.

Press any key to exit Tuner.

21

EDIT

Subtitles

Parameters

Algorithm been edited

Values

Edit

In the Edit menu, you always move by pressing the Cursor keys and change values by dialing the Adjust wheel.

Expert mode

When pressing OK on the Expert line, the M2000 will enable you to access a detailed Edit mode of the Reverbs.

Since the two different Edit modes (User & Expert) are not compatible, it is NOT possible to return to the User Edit mode. When

Storing a preset Edited in Expert mode, the current preset will remain in expert mode forever.

Combined Edit

See illustration on next page

The relative Levels of the two Engines can be adjusted in this display. The range is: off - 0.0 dB.

These levels affect both analog and digital outputs.

Move the marker by pressing the Cursor keys; change values using the Adjust wheel.

The Engine Out Levels are identical with the Outlev. parameter in the Edit page and will, at all times, be corresponding with these.

22

DYNAMIC MORPHING

Engine output levels [mix]

Dynamic Morphing section

Engine output levels

Morphing on/off and morphing direction

Morphing speed

Morphing threshold

Dynamic Morphing

The Dynamic Morphing function is a great new way of interaction between your source signal and the Effect.

When activated, the M2000 will morph between the two Engines according to your Input level. This is a function for quick seamless changes of an Effect.

Think about the vocal in a ballad being soft and subtle during the verse and then rising to heartbreaking heights in the chorus. Now imagine the Reverb changing along with it, from a small discreet

Room in the verse, to a Big Bright Hall in the chorus.

Simply select the two presets in the current Engines and then activate the Dynamic Morphing function. Set the Threshold and the Speed of the Dynamic Morphing and check out the result.

Morph direction 1-2:

If this box is selected, Engine 1 will be active while the Input is below Threshold.

Morph direction 2-1:

If this box is selected, Engine 2 will be active while the Input is below Threshold.

Note that the max. level of the Engines is set by the Engine Out bars above Dynamic Morphing.

The Dynamic Morphing is Stored along with Combined Presets.

The Dynamic Morphing function is only available when Routing is set to Parallel.

23

THE PROGRAMS

Reverb Programs

HALL-ROOM-PLATE-AMBIENCE-GATED

All Reverb presets both have a User and an expert page.

The number of parameters depends on which preset you have selected.

24

USER PARAMETERS

Decay

Sets the decay time. The value indicates the time to where the reverb tail is damped to -60dB.

Pre-delay

The time to arrival of the first reflection.

Reverb Lo

Adjust the low frequency reverberation time.

Reverb Mid

Adjust the mid frequency reverberation time.

Reverb Hi

Adjust the high frequency reverberation time.

Expert mode

Press OK here to enter expert mode. Remember there is no way back to normal user parameters, after adjusting any expert parameters.

HiCut freq.

Sets the cutoff frequency of the HighCut filter.

HiCut level

Damping ratio in dB of the HighCut filter.

Mix

Mix between direct and effect.

Out Level

Adjust output level. Use this parameter to match levels between presets.

EXPERT PARAMETERS

(only additional parameters mentioned)

Diffuse

This parameter sets the degree of wall diffusion. Increasing the value will result in a more dense reverberation tail. Dont set the value too high, as it will result in a not natural sounding reverberation tail.

Room shape

Here you can choose between different room shapes.

Changing the room shape will change the initial reflections.

Size mult.

Size multiplication factor. With this parameter you can change the size of the room. Only the initial reflections are influenced by this factor.

Lo Crossover

Crossover frequency between low and mid band reverberation filter.

Mid Crossover

Crossover frequency between lo-mid and hi-mid band reverberation filter.

Hi Crossover

Crossover frequency between mid and high band reverberation filter.

Initial lev.

Sets the Initial reflection level.

Rev.lev.

Level of the reverberation tail.

Rev.width

This parameter adjust the stereo width of the reverb tail.

Rev Feed

Determines how fast the reverberation will build up.

Rev.diff

Imposes the characteristics of the early reflections on the later reverberation.

Distance

The relative distance control varies the mix relations between early and later reflections. Simulating how far away you are from the sound source.

Difusor type

The natural room mode peak frequencies and the smoothness of the tail are affected by this parameter.

Mod Rate

The MODRATE varies the rate of modulation of the recirculating delay paths simulating the reverb tail.

Mod Depth

Controls the amount of delay path modulation or "wander" in the reverb.

Chorus Programs

These presets are capable of producing a smooth natural sounding stereo chorus effect. The Hicut filter gives you the ability to make it sound very warm.

Flanger Programs

The Presets range from very soft add-on effects to the wildest guitar sound you can imagine. The Feedback filters are capable of controlling both high frequency and low frequency feedback.

USER PARAMETERS

Speed

Controls the rate of sweep in a range from 1 sweep every 10 seconds to 10 sweeps every second.

Depth

Determines how wide a modulation (sweep) is produced.

Phase

Determines the sine wave modulation phase shift between left and right channels. At 0º the left and right modulation will move in sync. At 180º the modulation will move the channels against each other.

HiCut Freq.

Hicut shelving type filter (6dB/oct). This parameter sets the

»hinge« point of the shelving filter.

HiCut Level

Sets maximum depth of cut above the HiCut shelving frequency.

Delay

Controls the length of delay time.

Mix


Out Level


USER PARAMETERS

Speed


Depth


Phase


FB Level

Controls the amount of effect signal routed back to the flanger inputs. Select negative feedback to change feedback phase.

Delay


FB HiCut

Feedback High Cutoff frequency. Signal is damped 6dB/oct above this frequency.

FB LoCut

Feedback Low Cutoff frequency. Signal is damped 6dB/oct below this frequency.

HiCut Freq.

(see chorus)

HiCut Level

(see chorus)

Mix


Out Level


25

26

THE PROGRAMS... continued

Delay Programs

The Delay presets are capable of performing up to 1200 ms delay. The Feedback filters makes it possible to control both high and low frequency feedback.

Phaser Programs

USER PARAMETERS

Delay


FB Level

Controls the amount of effect signal routed back to the input.

FB HiCut

Feedback High Cutoff frequency. Signal is damped 6dB/oct above this frequency.

FB LoCut

Feedback Low Cutoff frequency. Signal is damped 6dB/oct below this frequency.

HiCut Freq.



HiCut Level


Mix


Out Level


USER PARAMETERS

Intensity

Phaser intensity.

Speed


Depth

Determines the depth of modulation.

HiCut Freq.



HiCut Level


Mix


Out Level


Multi Pitch-shift Programs

The Multi pitch presets are capable of performing 6 pitched Voices at the same time. This makes it possible to produce a true chorus effect.

USER PARAMETERS

Mix


Out Level


Voice

Sets which voice you are editing.

Pitch

Sets the pitch of the current Voice (0-1200).

Level

Sets the level of the current Voice.

Pan

Sets the panning of the current Voice.

Delay

Sets the Delay of the current Voice.

27

28

THE PROGRAMS... continued

EQ Programs

The EQ programs are all 3 band parametric types with separate high and low shelving bands.

Tremolo Programs

The Tremolo programs are effects where the output level is modulated by an LFO. Our programs are able of setting the

LFO phase between the two outputs.

USER PARAMETERS

Frequency

Low shelving filter ranges from 20hz to 5Khz

High shelving filter ranges from 500hz to 20Khz

Three band filters ranges from 20hz to 20Khz

Band width

Low and high shelving filters have 2 different bandwidths

The 3 bandfilters have 3 different bandwidths

Level

All filters range +/- 12dB.

EQ level

Adjustable +/-12dB.

USER PARAMETERS

Speed


Depth [intensity]


Phase


Mix


Out Level


Stereo Programs

USER PARAMETERS

Spatial

Controls the amount of spatial expansion.

HiCut Freq.



HiCut Level


Mix


Out Level


Dynamic Programs

COMPRESSOR-LIMITER-GATE-DE'ESSER

USER PARAMETERS

Attack

Dynamics attack time.

Release

Dynamics release time.

Ratio

Compression ratio.

Threshold (compressor)

Adjustable threshold level. The compressor will be engaged above this level.

Threshold (limiter)

Adjustable threshold level. The limiter will be engaged above this level.

Threshold (expander)

Adjustable threshold level. The expander is active below this level.

Gain (make-up gain)

The gain parameter compensates for the compression gain loss.

Deessing frequency

The de'essers attack frequency.

Deess damp

The damping ratio of unwanted »esses«..

29

THE RESET PAGE

Store and load your own default settings

Enter UserData page

Reset system parameters

Clear all user presets

Test Programs

Type your name here and your phone number

Place cursor here and press OK to finalize session.

How to enter the Reset page:

Hold one of the 3 Bypass keys pressed while power-up.

Move the marker using the Cursor keys and press OK to select the RESET type you desire.

Load User Default

This will reset all system parameters back to a Default setup made by you (See Store User Def). This reset will NOT delete the User presets of the M2000.

Store User Def

When you have a perfect setup of your M2000, you are able to

Store this as your own Default setup. This function is very useful, for example when you have finished a special production and want to go back to normal. When you have the perfect setup of your M2000, simply select this parameter and press OK to store your Default settings.

30

Set User Name

This function makes it possible to write your Name and Phone number into the M2000. Press OK to access the User data menu.

Use the ADJUST wheel and the Cursor keys to write your Name and Phone number into the M2000. Press OK to accept. Your

Name and Phone number will be displayed during power-up.

Reset System Parameters

This will reset all system parameters back to the Factory Default.

This reset will NOT delete the User presets of the M2000.

Reset all Presets

This will Clear all Ram Presets .

TECHNICAL SPECIFICATIONS

Digital Inputs and Outputs

Connectors:

Formats:

Output Dither:

Sample Rates:

Processing Delay:

Frequency Response DIO:

XLR (AES/EBU), RCA Phono (S/PDIF)

AES/EBU (24 bit), S/PDIF (20 bit), EIAJ CP-340, IEC 958

HPF TPDF dither 8 to 24 bit

32 kHz, 44.1 kHz, 48 kHz

0.2 ms @ 48 kHz

DC to 23,9 kHz ± 0,01 dB @ 48 kHz

Analog Inputs

Connectors:

Impedance:

Max. Input Level:

Min. Input Level (for 0 dBFS):

Sensitivity:

A to D Conversion:

A to D Delay:

Dynamic Range:

THD:

Frequency Response:

Crosstalk:

Analog Outputs

Connectors:

Impedance:

Max. Output Level:

Full Scale Output Range:

D to A Conversion:

D to A Delay:

Dynamic Range:

THD:

Frequency Response:

Crosstalk:

EMC

Complies with:

Safety

Certified to:

Environment

Operating Temperature:

Storage Temperature:

Humidity:

PCMCIA Interface

Connector:

Standards:

Card Format:

Control Interface

MIDI:

GPI, Pedal, Fader:

General

Finish:

Dimensions:

Weight:

Mains Voltage:

Power Consumption:

Backup Battery Life:

Warranty Parts and labor:

XLR balanced (pin 2 hot)

20 kohm

+22 dBu (balanced)

-10 dBu

@ 12 dB headroom: -22 dBu to +10 dBu

24 bit (1 bit, 128 times oversampling)

0.8 ms @ 48 kHz

>103 dB (unweighted), >106 dB(A)

-95 dB (0,0018 %) @ 1 kHz, -6 dBFS (FS @ +16 dBu)

10 Hz to 20 kHz: +0/-0.2 dB

<-80 dB, 10 Hz to 20 kHz, typical -100 dB @ 1 kHz

XLR balanced (pin 2 hot)

100 ohm (active transformer)

+22 dBu (balanced)

-10 dBu to +22 dBu

24 bit (1 bit, 128 times oversampling)

0.57 ms @ 48 kHz

>100 dB (unweighted), >104 dB(A)

-86 dB (0.005 %) @ 1 kHz, -6 dBFS (FS @ +16 dBu)

10 Hz to 20 kHz: +0/-0.5 dB

<-60 dB, 10 Hz to 20 kHz, typical -90 dB @ 1 kHz

EN 55103-1 and EN 55103-2 FCC part 15, Class B. CISPR 22, Class B

IEC 65, EN 60065, UL 1419, CSA E65

32° F to 122° F (0° C to 50° C)

-22° F to 167° F (-30° C to 70° C)

Max. 90 % non-condensing

PC Card, 68 pin type 1 cards

PCMCIA 2.0, JEIDA 4.0

Supports up to 2 MB SRAM

In/Out/Thru: 5 Pin DIN

1/4” phone jack, 0 ohm to 50 kohm

Anodized aluminum front, Plated and painted steel chassis

19" x 1.75" x 8.2" (483 x 44 x 208 mm)

5.2 lb. (2.35 kg)

100 to 240 VAC, 50 to 60 Hz (auto-select)

<20 W

>10 years

1 year

31

TROUBLESHOOTING

You press the POWER switch but there is no light.

- The power switch on the rear panel is switched off.

The input PPM meters dont peak out.

- You are using analog inputs, but the input selector in the I/O menu is set to digital in.

- The analog input level is set too low.

Only left input PPM meter is showing a signal.

- Set input selector (in I/O menu) to Both

No sound through the M2000.

- You are using analog inputs, but the input selector in the I/O menu is set to digital in.

You cant turn the power off.

- Hold the power switch pressed for at least 3 seconds.

All Program sounds »phased«

- You are using the M2000 in combination with a mixing console (send/return), but have not set Mix to 100%. You can do this permanently in the I/O menu.

Pedal works wrong

- Be sure the pedal is a »make« type.

32

MIDI IMPLEMENTATION CHART

STUDIO EFFECTS PROCESSOR M2000 - FEB 2, 1996 Version 1.0

Function

Basic Channel

Mode

Note Number

Velocity

After Touch

Pitch Bend

Control Change

Default

Changed

Default

Messages

Altered

True Voice

Note ON

Note OFF

Keys

Chs

Transmitted

1-3

1-16

X

X

X

X

X

X

X

X from 10 and up

Recognized

1-3

1-16

X

X

X

X

X

X

X

X from 10 and up

Remarks

Eng1: 1, Eng2: 2, Com: 3

Prog Change

True#

System Exclusive

Common :Song Pos

:Song Sel

:Tune

System real time :Clock

Aux Messages

:Commands

:Local ON/OFF X

:All Notes OFF X

:Active Sense

:Reset

X

X

O

X

X

X

O

X

O

0-127

Notes

O:YES

X:NO

Mode1: OMNI ON, POLY

Mode 3: OMNI OFF, POLY

O

0-127

O

X

X

X

O

X

X

X

X

X

Mode 2: OMNI ON, MONO

Mode 4: OMNI OFF, MONO

Cntl.#10: Mix (If available)

Cntl.#11: Output Level

Cntl.#12: First Param. on Edit page.

Cntl.#13: Second Param. on Edit page.

Cntl.#14: Third ....

Cntl.#15: ...

Cntl.#16: ...

Cntl.#17: ...

All Controllers are single byte type, scaled to parameter range.

33

SELF TEST

PRESS ONE OF THE 3 BYPASS KEYS, WHILE POWER-

ING UP, TO ACCESS THE SELF-TEST AND SELECT

»RUN TEST PROGRAM«

Turn the Adjust Wheel to scroll through Self tests

Key test

Select Key test by pressing OK.

The keys must be pressed in the order they are requested by the

M2000 to pass the test.

Press Cancel to exit Key test.

Adjust Wheel test

Select Adjust Wheel test by pressing OK

Turn the Adjust Wheel to 30 and back to 0 to pass test.

Press Cancel to exit Adjust Wheel test.

Led test

Select Led test by pressing OK

Turn Adjust Wheel to test the Leds. The test is ok when all

Leds are lit.

Press Cancel to exit Led test.

Display test

Select Display test by pressing OK

Press OK to check that all pixels are lit. Press any key to leave the pixel test.

Press Cancel to exit Display test.

Analog I/O test

Select Analog I/O test by pressing OK

Connect an Analog Output to the Analog Input, which has to be tested and press OK.

Use a balanced cable.

PPM must show -12 dB to pass test.

Press Cancel to Exit Analog I/O test

Digital I/O test

Select Digital I/O test by pressing OK

Connect a Digital Output to the Digital Input, which has to be tested and press OK.

The AES/EBU output can also be connected to the S/PDIF input and vice versa.

PPM must show 0 dB to pass test.

Press Cancel to exit Digital I/O test.

34

Midi I/O test

Select Midi I/O test by pressing OK

Connect Midi Out to Midi In.

Prg change 1-128 is send out on Midi Thru. Connect this socket to a Midi compatible device and confirm the Prg. changes.

Press Cancel to exit Midi I/O test.

Pedal test

Select Pedal test by pressing OK.

Connect a momentary pedal to the Pedal socket.

When pressing the Pedal, the Result should be OK.

When released, the Result should be Not OK.

Press Cancel to Exit Pedal test.

PCMCIA test

Select PCMCIA test by pressing OK

Insert PCMCIA card. Note that all Data on PCMCIA card will be destroyed.

Press OK to test.

Result reads:

Low battery - Time to change battery in your PCMCIA card.

Not Ok - Try the test using another PCMCIA card.

Press Cancel to Exit PCMCIA test.

Battery test

Select Battery test by pressing OK

Confirm that Result is ok.

Press Cancel to Exit Battery test.

System test

Select System test by pressing OK

Confirm that Result is ok.

Result reads:

Eeprom Not ok - The unit will most likely work ok, the message is for service matters only.

DSP Not ok - Contact your local dealer.

Press Cancel to Exit System test.

Power Off - On to start standard software.

GLOSSARY

AES/EBU

Professional digital in/out standard, using balanced XLR cables.

S/PDIF

Consumer digital in/out standard, normally using coaxial phonotype cables.

DITHERING

Dithering is a method to optimize the quality of a digital audio signal at low levels. A small amount of filtered noise is added to the signal, giving you a less distorted low level signal.

If you are using digital outputs, the equipment you feed determines the number of bits. A DAT recorder should always be dithered to 16 bit.

PROF/CONS LEVELS

Depending on which equipment you are using along with the

M2000, you must set the PRO/CON parameters correctly in the

I/O setup menu.

M2000 Analog Inputs:

Consumer range: -16dB to +10dB, nominal level = -10dB

Professional range: -6dB to +16dB, nominal level = +4dB

M2000 Analog Outputs:



The levels are either listed in the technical specifications or printed on the rear panel of the connected devices.

DE’ESSING

An algorithm that removes unwanted »esses« from a vocal material.

SYSTEM EXCLUSIVE MIDI COMMANDS

Device-dependent MIDI commands, normally used for remote controlling machines.

35

36

M2000 Hall

Great Vocal Hall

Very Big Hall

Warm MidSize Hall

Bright MidSize Hall

Small Hall

Nice Hall

Realistic Hall

Chorus Reverb

Synthesizer Reverb

Soundcheck Empty Arena

High School gym

Empty Theater

Airport Gate

Big Church

Arvo Part Cathedral

Taj Mahal

Big Snare Hall

Vintage Hall

Wood Floor

Stone Wall

Doubling Room

SlapBack Room

Sidewall Reflections

Backwall Reflections

True Room

Home Room

The Shop

The CORE Room

At Home

New Booth

Large Room

Medium Room

Small Room

Very Small Room

Small Wood Room

Small damped Room

Empty Room

Small Chamber

Very Small Chamber

Dark Chamber

Locker Room

Auditorium

Basement

Empty Garage

In the Bathroom

Classroom

33

34

35

36

37

28

29

30

31

32

23

24

25

26

27

18

19

20

21

22

43

44

45

46

47

38

39

40

41

42

13

14

15

16

17

10

11

8

9

12

5

6

3

4

7

1

2

PRESET LIST - SINGLE PRESETS

Tiled Room

Small Room for Drums

Percussion Room

Long Gold Plate

Medium Gold Plate

Short Gold Plate

Large Bright Plate

Snare Plate

Vocal dry

Vocal Wet

Air

Microphone Bleed

Small Studio Room

Small Box Ambience

Tiled Staircase

Nextdoor

Living Room

Phonebooth

Inside a Locker

Inside a Van

Tunnel

ZigZag Perc effect

Triple slap Reverb

Gated Reverb Short

Gated Reverb Medium

Gated Reverb Long

Gated Hall

Gated Room

Gated Gold Plate

Straight Delay

Soft Delay

Slapback Delay

The King Vocal Delay

Delay Doubler Effect

Old Tape Echo

Metallic Delay

In a Tin Can

Plain Chorus

Center Chorus

Chorus Extreme

Stereo Flange

Talking Flange

Dark Flanger

Phaser 1

Phaser 2

Phaser 3

Vocal Compressor

80

81

82

83

84

75

76

77

78

79

70

71

72

73

74

65

66

67

68

69

90

91

92

93

94

85

86

87

88

89

60

61

62

63

64

55

56

57

58

59

48

49

50

51

52

53

54

Guitar Compressor

Light Compressor

Heavy Compressor

Gain Maximizer

Pumpin Compressor

Heavy Limit

Limiter

Fast Gate

Slow Gate

Expander

Program De-Esser

Vocal De-Essing

Hard De-Essing

Neutral EQ

Bass EQ

Acoustic Guitar EQ

Loudness

Turn up the Bass

Air EQ

Telephone Voice

Voice Multipitch

6-Voice Bass Pitch

6-Voice Guitar Pitch

Fifths Up and Down

Barbershop

Mono to Stereo

Expanded Mono

Casual Panner

Straight Slow Panner

Fast Narrow Panner

Slow Tremolo

Fast Tremolo

Very Fast Tremolo

No Effect

122

123

124

125

126

127

128

117

118

119

120

121

112

113

114

115

116

102

103

104

105

106

107

108

109

110

111

95

96

97

98

99

100

101

PRESET LIST - COMBINED PRESETS

Two 2000 Halls

Deep Room

Smooth Hall

Small warm Hall

Giant Hall

Thick Drum Room

Thick Gated Reverb

Big Drum Hall

Two Verbs

Warm and Slow

Short + Slow Reverb

Big and Warm Hall

Nice Big Hall

Reverb along Reverb

Chorus-like Hall

Warm Vintage Hall

Fat Hall

Flanged Hall

Chorused Hall

Chorused Stonewall

Big Lead Guitar

Reverb + MultiPitch

Realistic Room

Reverb in Reverb

Biig Room

Short Room

Light Medium Room

Double Room

Flanged Small Room

Flanged Ambience

Flanged Room

Open up the Vocal

All Ambience

Far Away

Chorused Room

Sing in the Shower

Nice wide Vocal

Wide Room

Chorused Ambience

Room Multiplied

A litle to the Right

Wobbly Hall

Multiplex Hall

Chorus Doubler

Ultimative Chorus

Unchained Flanger

The King

33

34

35

36

37

28

29

30

31

32

23

24

25

26

27

18

19

20

21

22

43

44

45

46

47

38

39

40

41

42

13

14

15

16

17

10

11

8

9

12

5

6

3

4

7

1

2

Slapdelay along Hall

Slapdelay + Gateverb

Room + Long Delay

Very Long Delay-Verb

Right and Left

Subtle Slap

Clean Arpegio

Tap Dance Delay

Fast Flanged Delay

Nice Pitch + Delay

Bright Delay

Two Delays

Thick Delay

Telephone Delay

Slpabacking Flanger

Slapback and Doubler

Chorus + Delay

Beautiful SpaceDelay

Slow Reverb + Delay

Echo Chorus

Slowflange and Echos

Fizzy Echoes

Compressed Flanger

Comp + Gated Verb

Comp+ Small Drumhall

Compressed Snarehall

Compressed Room

Compressed + Hall

Vocal Comb + Delay

De-essed Delay

De-Essed M2000 Hall

De-Essed Bright Hall

De-Essed Basement

De-Essed Ambience

Heavy Limit+Expander

De-Esser + EQ

Compressor+De-esser

Limiter + EQ

Compressor + Expand

Compressor + Limiter

Vocal Compressor+EQ

LeslieLike Rotor

Panned Delay

Slow Panned Phone

Moving Ambience

Moving Vintage Hall

Autopanned Stonewall

80

81

82

83

84

75

76

77

78

79

70

71

72

73

74

65

66

67

68

69

90

91

92

93

94

85

86

87

88

89

60

61

62

63

64

55

56

57

58

59

48

49

50

51

52

53

54

122

123

124

125

126

127

128

117

118

119

120

121

112

113

114

115

116

102

103

104

105

106

107

108

109

110

111

95

96

97

98

99

100

101

Slapdelay in Circles

Doubler and Panner

Panned Inverse

Slow Moving Reverb

In Cirkles

Two Panners

True Stereo Delay

Stereo Garage

Stereo EQ

Stereo Compressor

Stereo Limiter

Stereo Gate

Short Stereo Delay

True Stereo Reverb

Insert Compressors

Insert EQs

Insert Gates

Echo in the Basement

Dynamic Flanger

Vocalroom-Choruslike

Short-Long Reverb

Compressor-Reverb

Bright -Warm Reverb

Warm-Bright Reverb

Chorus-Chorus

Dynmorph Looong Room

Hall-Ambience

Slapdelay-Vocal Wet

Delay-SlapDelay

Dynmorph SneakingVerb

Delay-Reverb

Reverb-Delay

Changing Ambience

Blues in a Room

37

M2000 JK.qxd

USERS MANUAL

TABLE OF CONTENTS

WELCOME

THE FRONT PANEL

THE REAR PANEL

THE SIGNAL FLOW

RECALL

STORE

THE WIZARD

I/O MENU

LEVELS MENU

ROUTING

UTIL/MIDI

TEMPO MENU

MIDI MONITOR

TUNER

EDIT

DYNAMIC MORPHING

THE PROGRAMS

THE RESET PAGE

TECHNICAL REFERENCE

TROUBLESHOOTING

MIDI IMPLEMENTATION CHART

SELF-TEST PROGRAM

GLOSSARY

PRESET LIST

WELCOME

About this Manual

The Help function

THE FRONT PANEL

THE REAR PANEL

THE SIGNAL FLOW

RECALL + SNAPSHOTS

The Recall Displays

Recalling a Preset

Combined Recall

Factory/User Presets

Snapshots

STORE

Store a new RAM Preset

The letterbox

Combined Store

Using a Memory Card:

THE WIZARD

I/O

I/O

Input

Sample rate

Mix

Status Bit:

Dither:

LEVEL MENU

Auto level

Ranges

ROUTING

STUDIO SETUP EXAMPLES

Use two sends on your mixing console

Create your own vocal reverb

Two individual inserts on your mixer

Post Production

UTIL/MIDI

How to move around

Display

Preset glide:

MIDI In

MIDI Out

MIDI Map

Security

Memory Protect

Memory Backup

Pedal

TEMPO

MIDI MONITOR & TUNER

MIDI Monitor

Tuner

EDIT

Edit

Combined Edit

DYNAMIC MORPHING

USERS MANUAL

The input PPM meters dont peak out.

You cant turn the power off.

tc electronic