HP-3000/4000
HP-3000/4000
Terminal User’s Guide
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and,
if not installed and used in accordance with the Installation Manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct the interference
at the user’s own expense.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglemente sure le
materiel brouilleur du Canada.
© 1998 through 2011 Schlage Biometrics, Inc. – ALL RIGHTS RESERVED
Document Part Number: 70100-6003 – Revision 3.3 – July, 2011
HandPunch is a trademark of Schlage Biometrics, Inc.
The trademarks used in this Manual are the property of the trademark holders. The use of
these trademarks in this Manual should not be regarded as infringing upon or affecting the
validity of any of these trademarks.
Schlage Biometrics, Inc. reserves the right to change, without notice, product offerings or
specifications.
No part of this publication may be reproduced in any form without the express written
permission from Schlage Biometrics, Inc.
Table of Contents
Introduction
Biometrics
3
Planning an Installation
Site Preparation 11
Principle of Operation
Specifications
HandPunch Placement Wiring Power Input Battery Backup Earth Ground and Shielding Communications External Devices 4
4
7
11
11
12
12
12
13
18
20
Mechanical Installation 23
Networking and Communications 27
Wiring Connections 31
Erasing the Memory 43
Closing the HandPunch 45
Enter Command Menu If No One is Enrolled in the HandPunch 47
Programming the HandPunch Service Menu 51
HandPunch Maintenance 69
Appendix A - Installation Tips 70
Wall Plate Installation Mounting the Wall Plate Stand-alone HandReader Master or Remote HandReader in a HandReader Network Remote HandReader in a HandReader Network Connected to a Host PC Remote HandReader Connected to a Host PC via Optional Modem Remote HandReader Connected to a Host PC via Optional Ethernet Printer If Users are Enrolled in the HandPunch Navigating Command Menus Setup Menu Management Menu Enrollment Menu Special Menu 23
24
27
27
27
28
29
29
47
47
49
54
56
60
63
67
Appendix B - Differences in Board Layout 72
Appendix C - Old Installation Guide 76
Appendix D - Troubleshooting 94
Glossary 96
Limited Warranty 98
HandPunch 3000/4000 Manual
Introduction
The HandPunch 3000/4000 is part of Schlage Biometrics’ 3rd generation line
of biometric hand geometry Time and Attendance Terminals1. The HandPunch
records and stores a three-dimensional shape of the human hand for
comparison and identity verification. Upon verification, the HandPunch records
the time, date, user ID number, and collected time and attendance data for
collection by a host computer. The HandPunch can produce an output that can
unlock a door and it can communicate with a host computer. The HandPunch
also has auxiliary inputs and outputs that can be used to control other systems
such as bells and alarms.
The HandPunch provides proof-positive employee verification combined
with the sophisticated operating features one expects in a modern Time and
Attendance Terminal. Because of this unique combination of capabilities, the
HandPunch provides the most accurate Time and Attendance data collection
terminal available. The key features of the HandPunch include:
•
•
•
•
•
•
•
•
•
Programmable Function Keys
- HP-3000 – 2
- HP-4000 – 10
User Time Restrictions
Supervisor Override at the “Time Clock”
- Add Punch
- Add Bulk Hours or Dollars
- Review Punches
Department Transfers
Explicit Punch Menu
Transaction Buffer
- HP-3000 – 5,120 event capacity
- HP-4000 – 7,680 event capacity
Bell Schedules
Door Control and Monitoring
Programmable Clock and Date Formats and Daylight Savings Switch-over
The HP-4000 also includes:
• Integrated Bar Code Reader
• Programmable User Messages
• Data Validation
1.
For the sake of using a consistent name throughout the manual, the HandPunch
3000/4000 terminal is referred to as the HandPunch for the remainder of this manual.
3
Introduction
Biometrics
Biometrics is a term describing the automatic measurement and comparison
of human characteristics. While its origins are ancient, the evolution of
advanced scanning and microprocessor technology brought biometrics into
everyday life. Electronic hand geometry technology first appeared in the
1970s. Schlage Biometrics Inc., founded in 1986, built the first mass-produced
hand geometry readers and made biometric technology affordable for the
commercial market. Today, Schlage Biometrics’ products are in use in every
imaginable application from protecting cash vaults to verifying employee
attendance in hospitals.
Principle of The HandPunch uses low-level infrared light, optics, and a CMOS camera
to capture a three-dimensional image of the hand. Using advanced
Operation
microprocessor technology, the HandPunch converts the image to an
electronic template. It stores the template in a database along with the user’s
ID number.
To gain punch, the user enters his or her ID number at the HandPunch’s
keypad or uses an external card reader. The HandPunch prompts the user to
place his or her hand on the HandPunch’s platen1. The HandPunch compares
the hand on the platen with the stored user’s unique template. If the images
match, the HandPunch records the transaction for processing.
The HandPunch is a time and attendance terminal designed for use with time
The
HandPunch and attendance software. Refer to “Figure 1-1” on page 5 and “Figure 1-2” on
page 6 when reviewing the information in this section.
Terminal
The HandPunch has an integrated keypad for ID entry and reader
programming. The HandPunch 3000 has two function keys (F1 and F2 – see
Figure 1-1). The HandPunch 4000 has ten function keys (F1 through F10 –
see Figure 1-2). These function keys can be programmed to collect data or to
activate auxiliary outputs. The CLEAR and ENTER keys assist in data
entry and programming.
1.
4
The Platen is the flat surface at the base of the HandPunch (see Figure 1-1). This
is where users place their hands for enrollment and verification. It has guide pins to
assist positioning the fingers during use.
HandPunch 3000/4000 Manual
Four different features assist the user with hand placement and read verification.
1.
2.
3.
4.
A light emitting diode (LED) hand placement display on the HandPunch’s top panel assists users with hand placement on the platen.
A liquid crystal display (LCD) shows operational data and programming menus.
“Red light/Green light” verification LEDs quickly inform users if their verification attempts were rejected or accepted.
An internal beeper provides audible feedback during keypad data entry and user verification.
HAND
PLACEMENT
DISPLAY
VERIFICATION
LIGHTS
LCD DISPLAY
Recog
nition
NUMERICAL
KEYPAD
1
4
7
*
No
8
0
2
5
9
Enter
ms In
c.
Clear
F1
F2
#
Nos
Ye
3
6
Syste
FUNCTION
KEYS
PLATEN AND GUIDE PINS
Figure 1-1: The HandPunch 3000
5
Introduction
HAND
PLACEMENT
DISPLAY
VERIFICATION
LIGHTS
LCD DISPLAY
Recog
nition
NUMERICAL
KEYPAD
1
4
7
*
No
8
0
2
5
9
s Inc.
Clear
F3
F1
F4
F2
#
Nos
Ye
3
6
System
F5
Enter
F6
F10
F7
F8
F9
BAR CODE
CARD
READER
FUNCTION
KEYS
PLATEN AND GUIDE PINS
: The HandPunch 4000
6
HandPunch 3000/4000 Manual
Specifications
Table 1: Specifications
Size:
8.85 inches wide by 11.65 inches high by 8.55 inches deep.
223 cm wide by 29.6 cm high by 21.7 cm deep.
Power:
12 to 24 VDC or 12 to 24 VAC 50-60 Hz, 7 watts
Weight:
6 lbs (2.7 kg) – 7 lbs (3.2 kg) with optional backup battery
Wiring:
2 twisted-pair, shielded, AWG 22 or larger (such as Belden 82732)
Temperature:
-10°C to +60°C – non-operating/storage (14°F to 140°F)
5°C to 40°C – operating (40°F to 110°F)
Relative Humidity NonCondensing:
5% to 95% – non-operating/storage (non-condensing)
20% to 80% – operating
Verification Time:
1 second or less
Memory Retention:
5 years using a standard internal lithium battery
Transaction Buffer:
ID Number Length:
HP-3000 – 5,120 transactions
HP-4000 – 7,680 transactions
1 to 10 digits
Baud Rate:
300 to 28.8 K bps
Communications:
RS-232, RS-422, optional Modem, optional Ethernet
User Capacity:
HP-3000 – 512 users expandable to 40,xxx
HP-4000 – 530 users expandable to 5,xxx
Message Capacity:
HP-4000 – 550 exandable to 3520 (not available with the HP-3000)
Function Keys:
HP-3000 – 2 user definable, HP-4000 – 10 user definable
Card Reader Input:
Proximity, Wiegand, Magnetic Stripe, Bar Code
(5 VDC provided by HandPunch unit)
Door Controls:
Lock output, Request to Exit input, Door Switch input
(open collector, 5 VDC present, sinks to ground, 100 mA max)
Alarm Monitoring:
Tamper, Door Forced
Event Monitoring:
There are a variety of monitoring options including events such as:
Invalid ID, Time Zone Violation, ID Refused, Try Again, Power
Failure
62 total: 2 fixed, 60 programmable
Time Zones:
7
Introduction
Table 1: Specifications
Time Schedules:
Auxiliary Inputs:
Auxiliary Outputs:
Options
HP-4000 – 3 definable time schedules per user
2 (open collector, 5 VDC present, sinks to ground, 100 mA max)
up to 3 user definable
(open collector, 5 VDC present, sinks to ground, 100 mA max)
HandPunch units have the following options available.
• Backup Battery Support See Technical Note 70200-0012 rev C
• Modem Communication See Technical Note 70200-0013 rev C
• Ethernet Communication See Technical Note 70200-0014 rev H
UL Compliance
Hand Readers are UL Listed as stand alone units only (i.e. the card reader function
has not been evaluated by UL).
The HandKey ll has not been tested for UL 294 in an Outdoor configuration.
approved
recyclable
8
HandPunch 3000/4000 Manual
This page is intentionally blank.
9
Introduction
This page is intentionally blank.
10
HandPunch 3000/4000 Manual
Planning an Installation
Site
Before you begin installation, check the site blueprints, riser diagrams, and
Preparation specifications for important information about the HandPunch’s location and
other systems that will connect to the HandPunch. Look for any existing wall
preparations and wiring that other contractors may have installed for the
HandPunch. A wire routing layout diagram (see “Figure 3-2” on page 25) is provided
to assist in planning.
HandPunch The recommended height for the HandPunch platen is 40 inches (102 cm)
Placement from the finished floor. The HandPunch should be out of the path of pedestrian
and vehicular traffic, and convenient too, but not behind the door it is controlling.
Avoid placing the HandPunch where users must cross the swing path of the door.
The HandPunch should be in an area where it is not exposed to excessive
airborne dust, direct sunlight, water, or chemicals.
40 in. (102 cm.)
Figure 2-1: HandPunch Placement Rules
NOTE
For the following sections, Schlage Biometrics does not supply hardware items
such as door control relays, door locks, switches, relays, communications or
power wiring.
11
Planning An Installation
Wiring
Four basic circuits typically connect to the HandPunch:
•
•
•
•
Power Input
Earth Ground and Shielding
Networking and Communications
External Devices
The minimum wire size for these circuits is AWG 22; the maximum wire size
is AWG 18. Schlage Biometrics recommends using Belden 82732 or its
equivalent when wiring for RS-422 communications.
Power
Input
The HandPunch uses an internal switching regulator to obtain internal
operational power. It accepts input voltages from 12 to 24 VDC or 12 to 24 VAC
at 50 to 60 Hz. The HandPunch comes with a 120 VAC to 13.5 VDC power
supply (Class 2, Model No. P48131000A010G-120 VAC, 60 Hz, 21 W, 13.5
VDC output @ 1000mA), if need an optional 220 VDC power supply is also
available (this power supply was not evaluated for UL 294).
To power the HandPunch with this power supply, a 120 VAC (or 220 VAC as
applicable) duplex outlet must be within 5 feet of the HandPunch. The power
supply has a 6-foot cable to provide a comfortable reach between power
outlet and HandPunch. The barrel jack at the of the power supply’s cable is
connected to J12 on the HandPunch PCB.
Battery
Backup
12
NOTE
J6 terminal 1 and the center pin of power jack J12 are connected together.
J6 terminal 2 and the sleeve of power jack J12 are connected together.
NOTE
Neither terminal 1 or terminal 2 is connected to the HandPunch ground.
NOTE
Do not connect a HandPunch’s power supply to a switched duplex outlet. The
HandPunch must have a constant source of power for proper operation.
The HandPunch uses an internal switching regulator to obtain internal
operational power. It accepts input voltages from 12 to 24 VDC or 12 to 24
VAC at 50 to 60 Hz. An optional power-fail protection circuit board can be
attached to the main circuit board to provide and control battery backup.
The design of the internal power supply is such that any range of the above
input voltages may be used and still provide proper battery charge voltage
and battery backup operation. Switch-over to battery power is automatic and
occurs when the input voltage falls to approximately 10.5 volts. At that time the
internal battery charger is disabled to save power and uninterrupted operation
continues on battery power.
HandPunch 3000/4000 Manual
When input power is restored, the HandPunch switches off of battery
operation and the battery charger is re-enabled to recharge the battery.
Battery charge voltage is set at approximately 13.65 volts, and battery charge
current is limited to approximately 50 mA. A fully discharged battery requires
approximately 12 hours of charge to fully recover.
Additional options installed and specific configurations within the HandPunch
make it difficult to predict precisely how long battery support will last, but in
general two hours of battery operation can be expected. While operating on
battery backup due to loss of main input power, the battery output voltage
is constantly monitored by internal circuitry. If the battery voltage reaches
approximately 9.5 volts the HandPunch automatically shuts down. This is done
to prevent full exhaustion of the battery. A yellow indicator on the top panel
illuminates to indicate that the HandPunch is running off of battery power. This
indicator extinguishes when main input power is restored.
Shunt J7 which is located to the left of TS3 see “Figure 4-1” on page 31 enables
or disables battery operation on those HandPunchs equipped with optional
battery backup. If a HandPunch does not have the optional battery backup
package installed, J7 is not used. On HandPunchs equipped with the battery
backup option, J7 allows service personnel a mechanism for disabling battery
backup operation before removal of main input power. To fully power down a
HandPunch equipped with battery backup, remove or reposition shunt J7 so
that the two pins protruding up from the main logic board are not connected
to each other. This effectively opens the circuit, removing the battery from any
internal circuitry. Main input power can then be removed and the HandPunch
will fully shut down. Once the HandPunch has fully shut down, shunt J7 may
be reinstalled. The design of the power supply is such that main input power
must be reapplied to re-enable the battery protection mechanism. If shunt J7
is not properly installed, the internal backup battery will not be charged, and in
the event of a main input power loss, the HandPunch will shut down.
The HandPunch with the battery backup option uses a 12 volt 800 ma/hour
sealed lead acid battery to provide backup battery power. This battery is
located immediately inside the rear panel of the HandPunch and plugs into
jack J4 on the keypad control circuit board located in the top of the chassis.
Earth
Ground
and
Shielding
Schlage Biometrics recommends that all HandPunchs be grounded with a
solid, reliable earth ground connection. This connection establishes a common
ground return point used to protect internal semiconductor devices from
ElectroStatic Discharge (ESD) and from external signal line transients. It also
provides a common signal level reference point between externally networked
HandPunchs. Schlage Biometrics recommends that the earth ground source
be identified by a qualified electrician familiar with electrical codes as well as
wiring and grounding techniques.
13
Planning An Installation
This is an extremely important and often overlooked aspect of hard-wired
serial communication systems. If the sending and receiving stations do not
agree on the ground reference for the signal voltages, communication errors
or a total inability to communicate may be observed. If the voltages are very
different, it is even possible to damage the units.
The subject of grounding can be complicated, and the full circuit of a system,
including power supplies and often even the building line power wiring, must
be understood. It is strongly recommended that a qualified electrician or
electrical engineer familiar with this subject be consulted when designing
the wiring of an HGU network installation. Always adhere to any applicable
electrical codes for your area. Schlage Biometrics is not responsible for
damage done to units due to improper wiring.
NOTE
Use any one of the following ground terminals to make the earth ground
connection: 4, 10, or 13. Do NOT use terminal 2 to establish the earth ground
connection; terminal 2 is not directly connected to ground.
14 13 12 11 10 9 8 7 6 5 4 3 2 1
CARD
READER
INPUT
SWITCH
INPUTS
OUTPUTS
AUX IN 2
GROUND
AUX IN 1
DOOR SWITCH
REX SWITCH
EARTH GROUND
GROUND
AUXOUT 2
AUXOUT 1
BELL OR DATA
LOCK OR CLOCK
CLOCK/D1
GROUND
DATA/D0
+5 VDC OUTPUT
1 2 3 4 5 6 7 8
9 10 11 12 13 14
ONNECTI
C
ON PIN
Figure 2-2: Earth Ground Connection Terminals
14
HandPunch 3000/4000 Manual
There are two standard methods for providing earth grounding to HandPunch
units:
•
•
earth grounding all units (see Figure 2-3)
carrying an earth ground to each unit (see Figure 2-4)
Earth ground all units when there is a good earth ground source near each
unit and/or when there are very long cable runs between units.
Carry an earth ground to each unit when there are no earth grounds
Earth Ground convenient to the unit and the unit’s power supply is floating.
All Units
One method of establishing a ground reference is to connect each unit’s
main board ground to earth ground. Earth ground is found on the third pin on
standard AC line sockets (in the United States, this is the round one in the
middle). If the building wiring is functioning correctly, this should be a lowimpedance path to a true ground, which then serves as a common reference
point for the units.
If this method of grounding the units is used, it is not necessary to connect the
units in the network together with a ground line in the communication cable.
Indeed, doing so could create ground loops—large-area loops which provide
a good coupling to external magnetic fields—which may actually compound
communication problems. If a magnetic field, such as that from a lightning
strike, induces a voltage in the ground loop, it is possible for large currents
to flow around the loop, which can raise the ground potential of some units
relative to others. When the shield or the cable is connected to any ground
in this configuration, it should be connected only at one end to prevent the
formation of ground loops.
For systems with multiple units on a network, there will be a series of cables
daisy-chained between the units, and the shield of each leg of the network
should be connected to ground at only one end. It does not matter which end.
An example of this method of grounding is shown in Figure 2-3.
15
Planning An Installation
GND
T+
Remote 2
Remote 1
Master
T-
GND
R+
GND
R-
R+
R-
Connect the
Cable Shield to
Remote 1's
Ground
Connect the
Cable Shield to
Remote 2's
Ground
To Next
Remote
Connect the Cable
Shield to the
Master's Ground
Do Not Connect
the Cable Shield
at this End
Do Not Connect
the Cable Shield
at this End
Do Not Connect
the Cable Shield
at this End
Figure 2-3: Communication Shielding with All Units Earth Grounded
All units are connected to the same earth ground. Each shield ground is
connected to only one unit, then interrupted to prevent the formation of ground
loops. Two sets of lines are wired as shown in Figure 2-3. It does not matter
significantly which unit’s GND is used for a particular shield, as long as the
path is broken from unit to unit.
Carry a
Ground Line
to Each Unit
The second method of establishing a ground reference in a system with
floating power supplies is to use the ground line in the RS-422 cable to
establish a common reference voltage for the communication signals. This line
should be connected to the negative power terminal on the data converter or
the ground line in the RS-232 port from the host PC system. It should then be
carried to one of the ground terminals on the back of each unit in the network.
An example of this method of grounding is shown in Figure 2-4.
GND
T+
Remote 2
Remote 1
Master
T-
GND
R+
R-
GND
R+
R-
To Next
Remote
Connect the Cable
Shield to the
Master's Ground
Connect Both Shields
to Remote 1 Ground
Connect Both Shields
to Remote 2 Ground
Connect Shield
to Next Remote
: Communication Shielding Carrying a Single Ground to Each Unit
If no earth ground is available at the units, this is the only possible method of
connecting the grounds. Even if an earth ground is available, depending on
the building’s power wiring and other environmental issues, this method may
be superior to the previous one, since it establishes the ground of each unit
independently of the building power lines. Local variations in grounds between
buildings, or from one point to another in a very large building, (perhaps due to
16
HandPunch 3000/4000 Manual
elevator motors or other large-current drawing machines) will have no effect on
the communication network if this configuration is used.
However, the power supplies must be truly floating, with no hidden paths back
to the high-voltage side of the transformers, or to earth ground. Since this
is difficult to achieve (there is always some parasitic capacitance between
the primary and secondary in any transformer), this method may be more
susceptible to high-frequency transients in the high-voltage side of the power
lines than the earth-grounded method.
The master unit’s ground establishes the ground for the entire system. The
main board ground points are connected to the shield ground at each unit,
but are not connected to earth ground. The ground point on the master can
be the data converter power supply negative terminal, or the GND pin on the
RS-232 cable. If the master is an HGU, its main board ground can be used.
This configuration should only be used if the power supplies to the units are
truly floating, otherwise ground loops will be created, and differences in local
grounds may cause large currents to flow through the cable shield.
17
Planning An Installation
Communications
HandPunch
to Host
Computer
Connection
HandPunch/host computer communications can be configured in one of three
ways:
RS-232 Host
Computer
Connection
A direct HandPunch connection to a host computer can be made through an
4-conductor cable in an RS-232 serial configuration. A 6’ or 50’ cable may be
purchased through Schlage Biometrics or a wiring diagram for the RS-232 to
host computer connection is found on “Table 4” on page 33.
NOTE
RS-422 Host
Computer
Connection
via a direct RS-232 connection
via a direct RS-422 connection using a data converter
via an optional Ethernet network connection (one HandPunch terminal
must have the Ethernet communication option installed)
• via an optional Modem connection (one HandPunch terminal must have
the Modem communication option installed)
•
•
•
If you make the RS-232 to host computer connection you cannot use the serial
printer option (see page 21).
A direct HandPunch network connection to a host computer can be made
through a shielded, 4-conductor cable in a full-duplex RS-422 configuration.
An RJ-11 jack must be installed within 6 feet of the host computer. Position
the RJ-11 jack using the template provided in this manual (see “Figure 3-2” on
page 25). The HandPunch RS-422 network is connected to this jack.
A data converter (Schlage Biometrics P/N: DC-102) is required to connect the
host computer to the RS-422 HandPunch network. The DC-102 is connected
to an available RS-232 serial port on the computer. Then connect the DC-102
to the RJ-11 jack using the 8 foot cable provided with the DC-102. A wiring
diagram for the RS-422 to host computer connection is found on page 31.
A HandPunch communication network is then connected, unit-to-unit, via an
RS-422 “daisy-chain” network. A network RJ-11 jack is installed on or in the
wall behind each terminal. Each RJ-11 jack is then interconnected in daisychain fashion using two, twisted-pair, AWG22 wires (Schlage Biometrics
recommends using Belden No. 82723 cable). The daisy-chain network can
extend up to 4,000 feet in length, and can have up to 31 HandPunch terminals
connected to it.
Connect the HandPunch terminal to the RJ-11 jack using the short silver cable
provided with the terminal.
18
HandPunch 3000/4000 Manual
NOTE
Hand
Punch
When wiring the RS-422 daisy-chain network, do not wire HandPunch
terminals in a “star” network (a network where a number of units are all
connected to the network at one, central location – see Figure 2-5).
Hand
Punch
Hand
Punch
Daisy Chain - OK
Hand
Punch
Hand
Punch
Hand
Punch
Hand
Punch
Hand
Punch
Star - Not Supported
Figure 2-5: Daisy-Chain Versus Star Network Communication Connections
Ethernet Host The HandPunch is available with an optional, internal Ethernet
Computer
communications module for TCP/IP communications between the HandPunch
Connection
network and the host computer. When connecting via an Ethernet connection,
one HandPunch terminal must be configured with this Ethernet option. This
terminal will communicate with the host computer.
To make the Ethernet connection, the Ethernet wiring must conform to
10BaseT standards. An Ethernet RJ-45 jack must be installed on or in the wall
behind the Ethernet HandPunch terminal. Position the jack location using the
template provided in this manual (see “Figure 3-2” on page 25). The cable from
the jack to the HandPunch is not provided with the Ethernet option. A wiring
diagram for the Ethernet to host computer connection is found on page 39.
IP Address and Gateway and Subnet Mask information is entered at the
HandPunch using the Set Serial command (see page 59).
Modem Host
Computer
Connection
The HandPunch is also available with an optional modem module for
telephone line communications between the HandPunch network and the
host computer. When connecting via modem, one HandPunch terminal must
be configured with the modem option. This terminal will communicate with the
host computer.
To make the modem connection, a telephone jack must be installed on or
in the wall behind the modem HandPunch terminal. Position the RJ-11 jack
location using the template provided in this manual (see “Figure 3-2” on page
25). The short black cable provided with the modem HandPunch connects the
terminal to the telephone jack. A wiring diagram for a modem to host computer
19
Planning An Installation
connection is found on page 40.
External Devices
The HandPunch can control external devices such as:
•
•
•
•
•
•
Bell
Door Lock
Request to Exit, Door Switch, and Auxiliary Inputs
Auxiliary Outputs
External Card Reader
Serial Printer
The HandPunch requires the use of an external DC power supply to operate
other controls or relays. The power supply can be of a different voltage than
that used to power the HandPunch. The bell, door lock, and auxiliary outputs
switch to ground when activated. For these devices, one pole of a control
relay is connected to the PLUS side of the power supply, and the other pole
connects to the output connection (switched minus) on the HandPunch.
The negative pole on the external power supply must connect to a negative
(ground) connection on the HandPunch to complete the circuit. The current
draw of the relay or external device must not exceed 0.1A.
Wiring for these devices should enter the HandPunch through the opening in
the center of the wall plate or through the conduit opening at the right side of
the HandPunch.
NOTE
The external DC power supplies and relays needed to operate external
devices such as bells or door locks are NOT provided by Schlage Biometrics.
You must provide these power supplies.
Bell
The bell control circuit switches direct current to ground when actuated. The
bell must receive its power from an external power supply through the contacts
of a bell control relay. Refer to the Bell Output Wiring Diagram on page 34.
Door Lock
The door lock control output of the HandPunch switches to ground upon
verification (unless programmed to send card data to a third-party control
panel). As the output is limited to 0.1A, a lock control relay must be used.
Refer to the Lock Output Wiring Diagram on page 35 for lock output wiring
connections. The relay and lock must receive power from an external power
supply.
20
HandPunch 3000/4000 Manual
Request to
Exit, Door
Switch, and
Auxiliary
Inputs
The HandPunch terminal has four inputs. Refer to the Inputs Wiring Diagram
on page 36.
•
•
•
Request to Exit
Door Switch
Two Auxiliary Inputs
A Request to Exit switch (REX) on the secure side of a controlled door will
activate the lock output. When the REX switch is pressed, the door unlocks for
a specified time. The REX switch must be a momentary contact, normally open
switch rated greater than 0.5 mA, 5 VDC circuit.
A Door Switch monitors door status – open or closed. The door switch must be
a normally closed switch rated greater than 0.5 mA, 5 VDC circuit.
Auxiliary Input requirements vary, depending upon the type of input device, but
the input device should be rated greater than 0.5 mA, 5 VDC circuit.
Auxiliary
Outputs
The HandPunch allows for the connection of up to three auxiliary output
devices. Refer to the Outputs Wiring Diagram on page 35.
External
Card Reader
You can connect an external card reader (such as a magnetic stripe, bar code,
or proximity reader) to a HandPunch. This external card reader provides a
secondary level of user identification.
NOTE
The HandPunch may require special format programming to be able to read
these external card reader formats. Contact your dealer for information.
The connection to an external card reader is made through TS-3 on the
HandPunch. Refer to the External Card Reader Wiring Diagram on page 37.
Serial Printer You can connect a serial printer to a HandPunch. A serial printer connected
to the HandPunch prints punches as they occur. Schlage Biometrics does not
supply serial printers. The connection to a serial printer is made through J4,
the 4 pin connector on the HandPunch. Refer to the Serial Printer Connection
Diagram on page 41. Refer to the Printer String Information Application Note
(available from Schlage Biometrics) for detailed information on connecting a
serial printer to a HandPunch.
NOTE
If you use the serial printer option you cannot use the RS-232 HandPunch
network to host computer option (see page 18).
21
Planning An Installation
This page is intentionally blank.
22
HandPunch 3000/4000 Manual
Mechanical Installation
Select an installation location based on the guidelines provided in the Planning
an Installation section beginning on page 11.
Wall Plate
Installation
NOTE
For the following instructions protect the HandPunch from the dust and debris
generated during the wall plate installation process.
1.
Remove the wall plate from the packing carton. Refer to Figure 3-1 for all
wall plate references in the following section.
LEVELING HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
3 LOWER SCREWS
Figure 3-1: Wall Plate
Measure and mark a point 42 1/2 inches (123 cm) from the surface of the
finished floor. This point will correspond to where the top-center point of the
HandPunch should be mounted.
3. For a hollow wall, drive a small nail into the wll at the mark and hang the
wall plate from the leveling hole located near the top of the wall plate.
4. For a solid wall, hold teh wall plate against the wall, centering the leveling
hole over the mark in the wall.
2.
23
Networking and Communications
Align a bubble level with the top edge of the wall plate and gently rotate the
wall plate until the bubble level shows that the totp edge of the wall plate is
level.
6. Secure the plate to the wall using heavy masking tape.
7. Using the wall plate as a template, mark the locations of teh two upper
screw holes and the three lower screw holes.
8. For a concealed wiring connection, trace the outline of the open area in the
center of the wall plate. Identify and mark a 1/2 inch hole through which the
HandPunch’s wiring will be mounted.
9. For a surface conduit wiring connection, mark the two conduit clamp holes
at the right side of the wall plate.
10. Remove the wall plate, masking tape, and the nail (if used).
5.
Mounting the 1. For a hollow wall, use the provided hardware to mount the wall plate. Use
Wall Plate
the two auger style fasteners for teh upper two mounting holes. Use the
toggle bolts for the three lower mounting holes.
2. For a solid wall, use expansion bolts to mount the wall plate. For all five
mounting holes, drill a 1/4 inch diameter hole, 1/4 of an inch deeper than
the length of the expansion anchor.
Routing the
Wiring
24
For a concealed wiring connection, drill a 1/2 inch hole in a convenient
location within the open area of the wall plate. Pull the wiring to enter the
HandPunch through this hole in the open area.
2. For a surface conduit wiring connection, drill a 1/4 inch diameter hole, 1/4
of an inch deeper than the length of the expansion anchor for each of the
two conduit clamp holes. Route 1/2 inch conduit to the HandPunch, ending
the conduit between the two conduit clamp holes. Pull the wiring to enter
the HandPunch through the conduit.
1.
HandPunch 3000/4000 Manual
WIRE ENTRY POINT
FOR RJ-11 JUNCTION BOX
Wall Plate
SURFACE
CONDUIT
ENTRY POINT
CL
1.25"
(3 cm)
50" Reference
(127 cm)
to Top of
Wall Plate
WIRE ENTRY POINT
FOR SURFACE
RJ-11 BOX
2"
(5 cm)
CL HandPunch
42.75"
(108.6 cm)
42.5"
(108 cm)
40.75"
(103 cm)
Finished Floor
Figure 3-2: HandPunch Wire Routing Layout
Attaching the 1. Remove the HandPunch from its carton.
2. Align the sleeves of the back plate with the pins of the wall plate and slide
HandPunch
the HandPunch to the left as shown in “Figure 3-3” on page 26.
25
Networking and Communications
HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
KEYHOLE
HOLES
3 LOWER
MOUNTING
SCREWS
REAR OF TERMINAL
: Attaching the HandPunch to the Wall Plate
3.
26
The Hand Punch is now ready for its wiring connections.
HandPunch 3000/4000 Manual
Networking and Communications
HandReader networking and communications can be configured in one of five
ways:
as a stand-alone HandReader
as a master or remote HandReader in a HandReader network
as a remote HandReader in a HandReader network connected to a host
PC
• as a remote network connected via optional Modem to host PC
• as a remote network connected via optional Ethernet to host PC
•
•
•
Stand-alone
HandReader
When installed as a stand-alone access control system there is no
communication wiring to other HandReaders or to a host computer. Power
input and control output wiring are all that are required. An RS-232 serial
printer output is available for event logging (refer to the Printer section on 29).
Schlage Biometrics highly recommends using Backhand™ software to backup
template information stored in the HandReader.
Master or
Remote
HandReader
in a
HandReader
Network
Multiple HandReaders can be linked together in a HandReader network.
Up to 32 HandReaders can be linked together on a 2-wire RS-485 or
4-wire RS-422 network (see Figure 3-1).
• Two twisted-pair, shielded, AWG 22 (or larger) wire should be used
(Schlage Biometrics recommends Belden 82732 or its equivalent).
• The wiring must be a “daisy-chain” network from HandReader to
HandReader and must not exceed 4,000 feet (1220 meters) in total length.
•
The master/remote network requires user enrollment at the “master”
HandReader. The master HandReader distributes hand template data with ID
numbrs and time restrictions (if any) to the other HandReaders in the network.
Users removed at the master HandReader are automatically removed from
the remote readers. A printer connected to the master HandReader will report
transactions from all Handreaders on the network.
Remote
HandReader
in a
HandReader
Network
Connected to
a Host PC
Multiple HandReaders can be linked to a presonal computer (PC) for an
integrated access control network. Real time monitoring of door status and
a variety of alarm types can be done with Schlage Biometrics’ HandNet for
Windows™ (Schlage Biometrics model number HN-300) software. To run
HandNet for Windows™, the computer must be PC compatible, using a
Pentium™-166 or faster microprocessor and it must have a CD-ROM.
•
The HandNet software can monitor over 1,000 HandReaders
simultaneously.
27
Networking and Communications
•
•
•
•
•
An unlimited number of sites can be created with up to 32 HandReaders
per site.
The HandReaders report all transactions to the PC. The HandNet software
records all transactions and displays a variety of reports generated from
this information.
Template management is handled automatically.
Users may enroll at any HandReader in the system. The PC collects the
data and distributes it to other HandReaders in the network.
Access may be restricted by time and by HandReader via HandNet’s
access profiles and by the use of time zones.
Typically, HandReader networks link to a PC using an RS-422 connection.
These networks have the following requirements:
Two twisted pair, shielded, AWG 22 wire or larger should be used (Schlage
Biometrics recommends Belden No. 82723 or equivalent cable).
• HandReaders must be wired together in a “daisy-chain” network from
HandReader to HandReader and then to the host PC. The total length of
teh wiring must not exceed 4,000 feet per network.
• The network requires an RS-422 to RS-232 converter (Schlage Biometrics
P/N DC-102) at the PC.
•
Schlage Biometrics’ optional HandNet for Windows™ software allows
programming of most of the remote HandReader setups from the computer.
However, each HandReader on the network requires the setting of an address.
HandReader addresses may be repeated, but only on different sites. Display
language, date format changes, and the communication mode must also be
set at the HandReader.
Remote
HandReader
Connected to
a Host PC via
Optional
Modem
28
An optional internal “answer only” 14.4 bps modem is available for
HandReaders. This modem is designed for operation with United States phone
systems. Site wiring should conform to standard telephone wiring standards
and terminate at teh HandReader with a standard RJ-11 modular phone
jack. Each HandReader with a modem includes a XXXX cable for the final
connection between the phone jack and the HandReader modem. Modem
HandReaders may be networked with up to 31 non-modem HandReaders
using RS-422 wiring. Refer to the Modem application note (available from
Schlage Biometrics) for detailed information.
HandPunch 3000/4000 Manual
Remote
HandReader
Connected
to a Host PC
via Optional
Ethernet
Printer
The HandReader is available with an optional internal Ethernet
communications module for TCP/IP communications. The wiring must
conform to 10BaseT standards. Typically, network wiring terminates at the
HandReader with a standard RJ-45 modular jack. The cable from the jack to
the HandReader is not provided with the Ethernet option. The IP address,
Gateway, and Host Bits are entered at the HandReader in the SET SERIAL
menu. Ethernet HandReaders may be networked with up to 31 non-Ethernet
HandReaders using RS-422 twisted pair cable. Refer to the Ethernet
application note (available from Schlage Biometrics) for detailed information.
A serial printer can be connected to a HandReader. A printer connected to a
remote HandReader will print only the events that occur at that HandReader.
Schlage Biometrics Inc. does not supply serial printers. Refer to the Printer
String application note (available from Schlage Biometrics) for detailed
information.
29
Networking and Communications
This page is intentionally blank.
30
HandPunch 3000/4000 Manual
Wiring Connections
Once the HandPunch is attached to the wall plate the wiring connections to
the HandPunch can be made (see Figure 4-1).
WALL
Power
Connectors
Reset
Switch
J7 Battery
Jumper
Wall Plate
Terminal
RJ-11 Strips Optional Modem Serial RS-232
or Ethernet
RS-422
Top of
Terminal
Top of HandPunch
Figure 4-1: Wiring Connections
Wiring
Examples
The following tables provide the pinouts for the terminal strips on the
HandPunch.
“Table 2” on page 32 provides the pinouts for TS-2: Input Connections.
“Table 3” on page 32 provides the pinouts for TS-3: Card Reader and Output
Connections.
• “Table 4” on page 33 provides the pinouts for the Serial RS-232 Connection.
• “Table 5” on page 33 provides the pinouts for the RS-422 HandPunch to
HandPunch Network Connection.
•
•
The following figures provide the pinout diagrams for the RJ-11 and RS-232
connectors:
“Figure 4-2” on page 33 provides the pinouts for J3, the RJ-11/RS-422
Network Configuration.
• “Figure 4-3” on page 34 provides the pinouts for J8, the RS-232 Serial Printer
Connection.
•
31
Wiring Connections
The following figures provide typical HandPunch wiring diagrams.
•
•
•
•
•
•
•
•
“Figure 4-4” on page 34 provides a typical Bell Output wiring diagram.
“Figure 4-5” on page 35 provides a typical Lock Output wiring diagram.
“Figure 4-6” on page 36 provides a typical Input wiring diagram.
“Figure 4-7” on page 37 provides a typical Card Reader Emulation Mode
wiring diagram.
“Figure 4-8” on page 38 provides a typical Host PC Network System wiring
diagram.
“Figure 4-9” on page 39 provides a typical Ethernet Network wiring diagram.
“Figure 4-10” on page 40 provides a typical Modem Network wiring diagram.
“Figure 4-11” on page 41 provides a typical Printer to HandPunch wiring
diagram.
Table 2: TS-2 - Input Connections
Terminal
Connection
9
Request to Exit Input
10
Ground
11
Door Monitor Switch Input (NC Standby)
12
Auxiliary Input 1
13
Ground
14
Auxiliary Input 2
Table 3: TS-2 - Output Connections
Terminal
32
Connection
1
+5 VDC @ 400mA Max. Output for External Card Reader
2
Card Reader: Wiegand D0 or Magnetic Stripe Data Input
3
Card Reader: Wiegand D1 or Magnetic Stripe Clock Input
4
Ground
5
Lock Output or Wiegand D1 or Magnetic Stripe Clock Output
6
Auxiliary Output 0 or Wiegand Data 0 or Magnetic Stripe Data Output
7
Auxiliary Output 1zt
HandPunch 3000/4000 Manual
Table 3: TS-2 - Output Connections
Terminal
8
Connection
Auxiliary Output 2
Table 4: RS-232 Connection
Pin
Signal
Connection
1
GND
Ground
2
RXD
Receive Data Input (from external device)
3
TXD
Transmit Data Output (to external device)
4
RTS
Ready to Send Output (to external device)
Table 5: RJ-11/RS-422 Network Connection
J3 Pin
Signal
1
Rx+
2
Rx-
3
Tx-
4
Tx+
J3 Pins
1 2 3 4
Figure 4-2: J3 - RJ-11/RS-422 Jack Pinout
33
Wiring Connections
RS-232 Pins
1
2
3
4
Figure 4-3: J4 - RS-232 Jack Pinout
* POWER SUPPLY
+12 to 24 VDC Max
+
NC
NO
*AUX
RELAY
BELL
+
-
WALL TO WHICH
THE HANDREADER
IS ATTACHED
HINGE
12 to 24 V
AC/DC
Input
1
14 13 12 11 10 9
2
8
7
6
5
4
3
2
1
RJ-11
RS-422
Connection
TOP OF THE
HANDREADER
* These components are not supplied by Recognition Systems, Inc.
** The operation of the Auxiliary Outputs depend upon how the inputs have been configured.
Figure 4-4: Bell Output Wiring Diagram
34
HandPunch 3000/4000 Manual
* POWER SUPPLY
+12 to 24 VDC Max
+
NC
*ELECTRIC LOCK
+ OR STRIKE -
NO
*LOCK
RELAY
WALL TO WHICH
THE HANDREADER
IS ATTACHED
HINGE
12 to 24 V
AC/DC
Input
1
14 13 12 11 10 9
2
8
7
6
5
4
3
2
1
RJ-11
RS-422
Connection
TOP OF THE
HANDREADER
* These components are not supplied by Recognition Systems, Inc.
** The operation of the Auxiliary Outputs depend upon how the inputs have been configured.
Figure 4-5: Lock Output Wiring Diagram
35
N.C. DOOR SWITCH*
REQUEST TO EXIT
N.O. MOMENTARY*
AUX INPUT 1**
N.O. DOOR SWITCH
SWITCH LEGEND
AUX INPUT 2**
Wiring Connections
WALL TO WHICH
THE HANDREADER
IS ATTACHED
HINGE
12 to 24 V
AC/DC
Input
1
14 13 12 11 10 9
2
8
7
6
5
4
3
2
1
RJ-11
RS-422
Connection
TOP OF THE
HANDREADER
* These components are not supplied by Recognition Systems, Inc.
** The operation of the Auxiliary Inputs depend upon how the inputs have been configured.
Figure 4-6: Request to Exit, Door Switch, and Auxiliary Inputs Wiring Diagram
36
HandPunch 3000/4000 Manual
Card Reader
GROUND
DATA 1
DATA 0
+5 VDC POWER
(SEE NOTE BELOW)
Access Panel
GROUND
DATA 1
DATA 0
WALL TO WHICH
THE HANDREADER
IS ATTACHED
HINGE
12 to 24 V
AC/DC
Input
1
14 13 12 11 10 9
2
8 7
6
5
4
3
2
1
RJ-11
RS-422
Connection
TOP OF THE
HANDREADER
NOTE: For +12 VDC readers, connect power supply +12 VDC to card reader.
Figure 4-7: Card Reader Emulation Mode Wiring Diagram
37
Wiring Connections
DC-102
RS-232 to 4-wire RS-422
Power Supply Data Converter (P/N DC-102)
B
DB-25
Serial
Port
Recogniti
on
1
2
4
5
7
8
*
No
0
3
6
9
* RS-422
4-Wire
(2 Twisted
Pairs)
Inc.
Clear
F1
Enter
HandPunch 1
Recogniti
on
4
7
*
No
2
5
8
3
6
9
0
Systems
* RS-422
4-Wire
(2 Twisted
Pairs)
Inc.
Clear
Enter
Recogniti
on
1
7
0
2
5
8
3
6
9
Systems
G
Y
J-3
* RS-422
4-Wire
(2 Twisted
Pairs)
Inc.
Clear
F1
Enter
B
HandPunch X
R
G
Y
J-3
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
R
F2
#
No
Yes
Y
F1
HandPunch 2
No*
G
J-3
B
4
R
F2
#
No
Yes
Y
RJ-11 Jack Surface
or Wall Plate
B
1
G
F2
#
No
Yes
Systems
R
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 4-8: Host PC to RS-422 Direct-Connect Network System Wiring Diagram
38
HandPunch 3000/4000 Manual
RSI Supplied Cable (Black)
Recogniti
on
1
4
7
*
No
8
0
2
5
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
6
Enter
Modem Unit
HandPunch
Modem Port
RJ-11 Telephone Outlet
HandPunch RS-422
RJ-11 Port
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
RJ-11 Jack Surface
or Wall Plate
Recogniti
on
1
2
4
5
7
8
*
No
0
3
6
9
Inc.
F1
F2
#
No
Yes
Systems
Clear
Enter
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
HandPunch 1
Recogniti
on
1
4
7
*
No
2
5
8
0
3
6
9
#
No
Yes
Systems
Inc.
Clear
F1
F2
Enter
B
R
G
Y
HandPunch 2
Recogniti
on
1
4
7
*
No
5
8
0
2
6
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
* RS-422
4-Wire
(2 Twisted
Pairs)
Enter
B
R
G
Y
HandPunch X
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 4-9: Host PC to HandPunch Ethernet Connection Diagram
39
Wiring Connections
Ethernet Cable
Recogniti
on
1
4
7
*
No
2
5
8
0
3
6
9
Connection to
Host Computer
via Ethernet
HandPunch
Ethernet Port
Inc.
Clear
F1
F2
#
No
Yes
Systems
Enter
HandPunch
RS-422
RJ-11 Port
Ethernet Unit
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
RJ-11 Jack Surface
or Wall Plate
Recogniti
on
1
2
4
5
7
8
*
No
0
3
6
9
Inc.
F2
#
No
Yes
Systems
Clear
F1
Enter
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
HandPunch 1
Recogniti
on
1
4
7
*
No
2
5
8
3
6
9
0
Inc.
F1
F2
#
No
Yes
Systems
Clear
Enter
B
R
G
Y
HandPunch 2
Recogniti
on
1
4
7
*
No
8
0
2
5
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
6
* RS-422
4-Wire
(2 Twisted
Pairs)
Enter
B
R
G
Y
HandPunch X
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 4-10: Host PC to HandPunch Modem Connection
40
HandPunch 3000/4000 Manual
*Host Computer/Hyperterminal
*Serial Printer
WALL TO WHICH
THE HANDREADER
IS ATTACHED
HINGE
HINGE
12 to 24 V
AC/DC
Input
1
4 Pin
Connector
14 13 12 11 10 9
2
RJ-11
RS-422
Connection
8
7
6
5
4
3
2
1
J4
RS-232 Jack
TOP OF THE
HANDREADER
* These components are not supplied by Recognition Systems, Inc.
Figure 4-11: HandPunch to Serial Printer or Host Computer Wiring Diagram
41
Wiring Connections
This page is intentionally blank.
42
HandPunch 3000/4000 Manual
Erasing the Memory
There are two options when erasing the memory of the HandReader:
1.
2.
Setup
All
The erasing of the setup will set the HandReader’s address, passwords, etc.,
back to factory defaults.
Erasing
HandReader
Memory
Choosing the All option will take the HandReader’s setup back to factory
defaults plus erase all user databases and datalogs. This action cannot be
undone. If there is a software that is managing the system then the users can
be downloaded back to the HandReader if needed.
The erase memory function allows a HandReader’s setup and/or user
database to be erased.
Perform the following steps to erase the setup programs but retain the user
database.
1.
2.
3.
With system power OFF, depress reset switch.
Turn system power ON and wait 5 seconds.
LCD screen will display.
ERASE
:1 SETUP
:9 ALL!!!
43
Planning an Installation
This page intentionally blank.
44
HandPunch 3000/4000 Manual
Closing the HandPunch
Before closing the HandPunch clear all dust and debris away from the
HandPunch. With the wal mount latch in the unlocked position, swing the body
of the HandPunch up and lock the latch into place with the key provided with
the HandPunch (see Figure 6-1 below).
Dust and debris surrounding the HandPunch can drastically affect the
terminal’s operation. It is important to ensure the HandPunch is free from dust
and debris before closing the terminal.
Do not force the HandPunch onto the wall mount latch when the latch is
in the locked position.
Wa l l P l a t e
etsyS
m
.cnI s
goceR
noitin
Latch
Key
oN
LOCK
Unlocked Position
Wa l l P l a t e
Latch
Key
Locked Position
Figure 6-1: Closing the HandPunch
45
Planning an Installation
This page intentionally blank.
46
HandPunch 3000/4000 Manual
Enter Command Menu
Press the CLEAR and ENTER keys simultaneously to enter a
command menu.
If No One
is Enrolled
in the
HandPunch
1.
The display appears as follows:
ENTER PASSWORD
2.
Press the default password for the menu you wish to enter.
Press 1 for the Service Menu.
Press 2 for the Setup Menu.
Press 3 for the Management Menu.
Press 4 for the Enrollment Menu.
Press 5 for the Security Menu.
3.
If Users are
Enrolled
in the
HandPunch
1.
Press ENTER and the first command option in the selected menu
appears.
The display appears as follows.
ENTER ID
*:
Enter your ID number on the keypad and place your hand on the platen for
verification.
3. If verification is successful, the display appears as follows.
2.
47
Enter a Command Menu
Enter Password
4.
Enter the password for the menu you wish to enter. The default passwords
are as follows:
Press 1 for the Service Menu.
Press 2 for the Setup Menu.
Press 3 for the Management Menu.
Press 4 for the Enrollment Menu.
Press 5 for the Security Menu.
Press ENTER
If you are authorized to use this command, the first command option in the
selected menu appears.
7. If you are not authorized to enter this command, the display appears as
follows:
5.
6.
ENTER ID
*:
NOTE
NOTE
48
To access these menus you must be the first person enrolled in a new system
installation or you must have been enrolled as a supervisor. If you are blocked
from the supervisory menus, verify your access rights with management
personnel. If enrollment information has been incorrectly changed and you
must have supervisory access to all menus, make these changes through
software.
It is possible to physically reset the HandPunch’s memory, however resetting
memory sets all unit parameters back to the factory default values. Resetting
memory allows access to all menus by the first person enrolled (as if it is
a new system installation), but this means that all employee information
programmed into the HandPunch is lost and must be re-entered
manually. Be sure you need to reset memory before performing this function.
To reset memory, refer to the Erasing HandPunch Memory section on page 43.
HandPunch 3000/4000 Manual
Navigating
Command
Menus
Once you have entered a command menu, there are three options available for
navigating the command menu system
•
Press # to enter the command shown on the display.
•
Press * to step to the next command in the menu.
•
Press CLEAR to exit the command menu (pressing any numeric key also
exits the command menu). If you are in a command’s sub-menu, you may
have to press CLEAR multiple times to completely exit the command
menu.
49
Enter a Command Menu
This page is intentionally blank.
50
HandPunch 3000/4000 Manual
Programming the HandPunch
The HandPunch is programmed via a series of command menus. A summary
of the menus and commands is given in Table 6.
Table 6: Basic Command Mode Structure
Service Menu
Setup Menu
Password 1
Calibrate
Password 2
Set Language
Status Display
Set Date Format
Set Time and
Date
Set Address
Set ID Length
Set Serial
Management
Menu
Password 3
Supervisor
Override
List Users
Enrollment Menu
Password 4
Add Employee
Set User Data
Remove User
Security Menu
Password 5
Special Enroll
Add Supervisor
Restrictions
Set Reader Mode
Upgrade
To control access to the command menus, each menu has a unique password.
This password is requested as a part of the process for accessing each menu.
A supervisor must enter the correct password for that menu to access that
menu. The default menu passwords are given in Table 6.
To increase the security of the HandPunch, Schlage Biometrics recommends
changing the passwords for the command menus to new numbers. These
password numbers can be up to 10 digits long. This is done with the Set
Passwords command described on.
Authority Level
A second method for controlling access to the command menus is through
the use of Authority Levels. Authority Levels control whether or not a user has
access to the command menus.
Level 0 is for a user who does not need access to any of the command
menus.
• Level 5 is assigned to Supervisors who need access to all of the command
menus.
•
51
Programming the HandPunch
The HandPunch automatically assigns Authority Level 0 to users enrolled by
the Add Employee command. Authority Level 5 is automatically assigned to
users enrolled by the Add Supervisor command.
NOTE
Until a user has been assigned to Supervisor, every user can access every
menu. Once a user has been enrolled using the Add Supervisor (designated
as a supervisor), all further user authority levels are assigned. The first person
enrolled should be enrolled using the Add Supervisor command. This protects
the integrity of the system. Schlage Biometrics strongly recommends enrolling
at least two users as supervisors to ensure that more than one person has the
authority to access all menus and all commands.
Programming Order
When setting up HandPunch operations there is a general programming/
operations order that should be followed.
Set HandPunch Site Parameters – Set the HandPunch site parameters to
meet site-specific needs and usage: change the language used by the
display, set the HandPunch’s address, and set the serial communication
baud rate (used if you have installed a serial printer – see page 56).
Enroll Supervisory Staff – Enroll yourself and the supervisors who will have
responsibility for HandPunch management. This is done through the
Enrollment Menu (see Supervisor Enrollment on page 66).
NOTE
The time, date, and ID number length are normally set by the host computer.
However, a supervisor can change these parameters at a HandPunch after
setup information has been downloaded from the host computer.
These tasks are done through the Setup Menu. The instructions for
reader setup parameters begin on page 56.
Train and Enroll Users – Train each user regarding HandPunch usage and
then Enroll each user. This is done through the Enrollment Menu. The
instructions for employee enrollment begin on page 66. Special enrollment
allows you to enroll people with disabilities that prevent them from using
the HandPunch properly. Employees with special enrollment ID numbers
can punch in without biometric verification.
WARNING
52
This means that anyone who knows a special enrollment ID number can
punch in. This function should only be used if absolutely necessary. The
instructions for special enrollment begin on page 68.
HandPunch 3000/4000 Manual
System Management
Onca a HandPunch system is in operation the following commands are used
for system management.
Supervisor Override – Review employee punch history, add bulk hours or
dollars, or record a punch for an employee. This is done through the
Management Menu. The instructions for supervisor override begin on
page 61.
List Users – List the users authorized to use a HandPunch. This is done
through the Management Menu. The instructions for listing employees
begin on page 62.
Set User Data – Set a user’s reject threshold (adjusting the sensitivity applied
when a HandPunch reads a hand) and assign time zones to users
(defining when users are allowed to punch in and out). These tasks are
done through the Management Menu. The instructions for setting user
data begin on page 62.
Restrictions – Set or remove time restrictions for when employees punch in.
This is doen through the Management Menu. The instructions for setting
in time restrictions begin on page 62.
Remove User – Remove employees (and supervisors) from a HandPunch.
This is done through the Enrollment Menu. The instructions for removing
employees begin on page 66.
Set Amnesty¹ – Temporarily remove time resrictions at a HandPunch to
accommodate circumstances that may affect when employees punch
in (such as inclement weather). This is done through the Management
Menu. The instructions for setting amnesty begin on page 62.
1. On HandPunch 4000 units only.
53
Programming the HandPunch
Service Menu
The Service menu commands provide information that help you determine if
the HandPunch is performing within normal operating parameters and identify
the status of the unit’s inputs and outputs. The following section provides a
brief summary of the Service Menu commands.
NOTE
Navigating
the Service
Command
Menu
There are no user serviceable parts inside the HandPunch.
Enter the appropriate password to enter the Service command menu. Once
you have entered the command menu, there are three options available for
navigating the command menu system.
•
Press # to enter the command shown on the display.
Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also
exits the command menu). If you are in a command’s sub-menu, press
CLEAR multiple times to completely exit the command menu.
•
Service
Commands
There are two commands available from the Service command menu.
•
•
Calibrate
Status Display
Refer to Table 7 and identify the command you need to perform. Step through
all previous commands until you reach the desired command.
Table 7: Service Command Menu
Service Menu
Password = 1
Calibrate
Recal (Y/N)
Status Display
On/Off (Y/N)
54
HandPunch 3000/4000 Manual
Calibrate
The Calibrate command displays the HandPunch’s exposure values, allowing
you to verify these values are within normal operating parameters. The
standard operating parameters are shown in Table 8.
Table 8: Normal Operating Parameters
Parameter
Row “r”
Column “c”
Exposure “e”
Normal Range
0 +/- 2
0 +/- 2
100 +/- 20
Status Display The status display command allows you to enable or disable the displaying of
the following information.
•
•
the status values of HandPunch inputs and outputs
the hand read score of the last user to verify on the system
When the status display is enabled, Figure 8-1 identifies each status display
field value.
- ENTER ID O C O C O H L H L NN
O C O C O
H L H L NN
Last Hand Read Score
Aux Out 2
Aux Out 1
* Aux Out 0
* Lock
Aux In 2
Request to Exit
Aux In 1
Door Monitor Switch
Tamper
* These status values are inactive if the
reader is in Card Reader Output Mode.
O = Circuit Open
C = Circuit Closed
H = Output is OFF (High)
L = Output is ON (Low)
Figure 8-1: Status Display Chart
55
Programming the HandPunch
Setup Menu
The Setup menu commands allow you to set the basic operating parameters
for the HandPunch unit. The following section provides a brief summary of all
the parameters that may be set on a HandPunch unit.
NOTE
Navigating
the Setup
Command
Menu
Once in the Command Menu, you can step through and set the parameters
for each command sequentially. You do not have to exit command mode after
setting any individual command.
Enter the appropriate password to enter the Setup command menu. Once
you have entered the command menu, there are three options available for
navigating the command menu system.
Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key
also exits the command menu). If you are in a command’s sub-menu, press
CLEAR multiple times to completely exit the command menu.
•
Setup
Commands
There are six commands available from the Setup command menu:
•
•
•
•
•
•
•
Set Language
Set Date Format
Set Date and Time
Set Address
Set ID Length
Set Serial
Set Output Mode
Refer to “Table 9” on page 57 and identify the command you need to perform.
Step through all previous commands until you reach the desired command.
56
HandPunch 3000/4000 Manual
Table 9: Setup Command Menu
Setup Menu
Password = 2
Set Language
Select Language
Set Date Format
Select Date Format
Set Time and Date
Month (MM)
Day (DD)
Year (YY)
Hour (HH)
Minute (MM)
Set Address
New Address
Set ID Length
New ID Length
Set T & A Mode
a
Set Serial
RS-422 (Y/N)
Select Baud Rate
RS-232
Select Baud Rate
Use RS-232 for Printer or Host
57
Programming the HandPunch
Table 9: Setup Command Menu
Setup Menu
Password = 2
a
Set Serial
Verify/Enter IP Address
Verify/Enter Gateway
Verify/Enter Host Bit
Set Output Mode
For Lock & Auxiliary (Y/N)
For Card Reader Output (Y/N)
Upgrade
Code
a.
The Set Serial command has different
values based on whether the HandPunch
unit is configured for serial or modem
communication versus Ethernet
communication.
Set Language The Set Language command allows the language shown on the HandPunch’s
display to be “localized” for a variety of countries:
-
-
-
-
-
Set Date
Format
58
-
-
-
-
-
German
Russian
Indonesian
Portuguese
Polish
The Set Date Format Command allows the date format shown on the
HandPunch’s display to be “localized” for a variety of countries.
-
-
-
-
Set Time
and Date
English
Japanese
French
Italian
Spanish
mm/dd/yy
dd-MMM-yy
dd-mm-yy
dd/mm/yy
- mm-dd-yy
- MMM dd,yy
- ddMMMyyyy
The Set Time and Date command allows the HandPunch’s time and date to be
set. This is normally not necessary as the HandPunch’s time and date are set
by the host computer.
HandPunch 3000/4000 Manual
Set Address
The Set Address command allows a unique address to be set for each
HandPunch in a network. For proper operation, each HandPunch in the
network must have a unique address. All units may use any address from 0 to
254. All units are sent with the address set to 1.
Set ID Length The Set ID Length command allows you to reduce the number of keystrokes
required to enter the ID number by eliminating the use of the ENTER key
to complete an ID number entry. Once the ID Length is set, the HandPunch
will automatically accept an ID number entry once the correct number of
characters have been entered.
Set ID Length does not apply when ID entry is made from a card reader. Once
the ID Length is set, the T & A Mode Set command appears, allowing you
to configure the HandPunch to prepare punch data for time and attendance
software.
Set Serial
The Set Serial command allows you to set communication parameters
depending upon the communication method for which the HandPunch has
been configured. Different configuration parameters are entered based on if
the unit is configured for a direct-connection or a modem connection, or if the
unit is configured for Ethernet communication.
The unit defaults to the RS-422 communication mode unless a modem or
Ethernet module has been installed. The unit defaults to 9600 bps which is
suitable for most communication applications.
If an Ethernet module has been installed, the IP Address and Gateway and
Subnet Mask must be set. The host bits should be left at 0, if communicating
across a LAN.
Set Output
Mode
The Set Output Mode command allows you to set how the output relays
operate. The relays should be set based on the HandPunch application.
Set the HandPunch to Lock/Auxiliary Relay mode if the unit is acting as door
controller (this is the factory default setting).
Set the HandPunch to Card Reader Emulation mode if the unit is outputting to
an access control panel.
Upgrade
This Upgrade Menu is where the HandPunch code gets input to allow for a
Memory Upgrade.
59
Programming the HandPunch
Management Menu
The Management menu commands allow you to manage employee data
stored in a HandPunch unit. The following section provides a brief summary of
the employee data that may be manipulated on a HandPunch unit.
Enter the appropriate password to enter the Setup command menu. Once
you have entered the command menu, there are three options available for
navigating the command menu system.
•
Press # to enter the command shown on the display.
Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also
exits the command menu). If you are in a command’s sub-menu, press
CLEAR multiple times to completely exit the command menu.
•
There are four commands available from the Management command menu.
•
•
•
•
Supervisor Override
List Users
Set User Data
Restrictions
Refer to Table 10 and identify the command you need to perform. Step through
all previous commands until you reach the desired command.
Table 10: Setup Command Menu
Setup Menu
Password = 3
Supervisor Override
Review
ID #
Add
Bulk Hours
Bulk Dollars
Punch
60
HandPunch 3000/4000 Manual
Table 10: Setup Command Menu
Setup Menu
Password = 3
List Users
Display
Print
Set User Data
User Reject
User Time Zone
Amnesty
Set Restrictions
On/Off (Y/N)
Supervisor
Override
The Supervisor Override command allows you to review an employee’s punch
record, add or remove bulk hours or dollars to an employee’s punch record, or
add a new punch to an employee’s punch record (see “Table 11” on page 62 for
a description on Punch Type codes).
61
Programming the HandPunch
Table 11: Punch Type Information
T & A Code
1
2
3
4
5
6
7
8
9
15
Type
IN
Back From Lunch
Out
Department Code
Back From Break
-not usedCalled Back to Work
Supervisor Entered Hours
Supervisor Entered Dollars
Supervisor Entered Category
List Users
The List Users command allows you to display or print a list of all the
employees enrolled in a HandPunch.
Set User
Data
The Set User Data command allows you to set an employee’s Reject
Threshold (adjusting the hand read threshold for one employee without
affecting the threshold of other employees), set an employee’s Time Zone (the
hours an employee is allowed access), and set employee Amnesty (removing
time zone restrictions for a specified number of punches – available on the HP4000 only).
Restrictions
The Restrictions command allows you to enable or disable employee punch
time restrictions, allowing or disallowing punches outside an employee’s
assigned time zone.
62
HandPunch 3000/4000 Manual
Enrollment Menu
Enrollment is the process of recording a hand image and associating it with
an ID number. The first person to enroll in the HandPunch has access to
all command menus. This person should enroll using the Add Supervisor
command (see page 66). Once a supervisor has been enrolled, all further
enrollments use the following rules:
A user enrolled through the Add Employee command (page 66) is assigned
Authority Level 0. This allows the user to punch in and/or gain access
through a door secured by the HandPunch.
• A user enrolled through the Add Supervisor command (see page 66) is
assigned Authority Level 5. This allows the supervisor to punch in and
gain access through a door secured by the HandPunch, and it allows the
supervisor to access all command menus.
•
NOTE
Navigating
the Setup
Command
Menu
Until a user has been assigned to Authority Level 5 using the Add Supervisor
command, every user with Authority Level 0 can access every menu. This is
done to ensure that the first person enrolled is able to access all the menus
to perform all the programming required to support the HandPunch. Once a
user has been enrolled using the Add Supervisor command, all further user
authority levels are assigned as per the list above. This protects the integrity
of the system by enacting the Authority Level rules described above. Schlage
Biometrics strongly recommends enrolling at least two users as supervisors to
ensure that more than one person has the authority to access all menus and
all commands.
Advance planning and training make enrollment fast and easy. Users
should be informed on what to expect and how to place their hands on the
HandPunch before you enroll them.
Enter the appropriate password to enter the Setup command menu. Once
you have entered the command menu, there are three options available for
navigating the command menu system.
•
Press # to enter the command shown on the display.
Press # to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also
exits the command menu). If you are in a command’s sub-menu, press
CLEAR multiple times to completely exit the command menu.
•
63
Programming the HandPunch
Preparation
Here are a few guidelines to help you prepare for an enrollment session:
•
•
•
•
•
User
Education
The HandPunch is easy to use and non-threatening. However, most
people have never used a biometric HandPunch. Training users on how the
HandPunch works and how to use it will eliminate most fears and concerns
before they occur. Inform the users of these facts.
•
•
•
•
•
•
Proper Hand
Placement
The HandPunch reads the shape of the hand, not the fingerprints or
palmprints.
It does not identify people. It confirms people’s identity.
It scans with an invisible light of the type used in TV remote controls.
It does not transfer germs any more than a doorknob or money.
It does not invade privacy; it guarantees it.
The enrollment process requires three or more reads to collect enough
information to create a template.
For correct, consistent hand reads it is very important that your hand is placed
on the platen in the same manner every time. The following rules apply for
proper hand placement on the platen also refer to “Figure 8-2” on page 65.
•
•
•
•
•
•
64
You can enroll one person or a group of people during an enrollment
session.
Each user must have a unique personal identification (ID) number. It will
save you considerable time if you assign the ID numbers in advance (Refer
to the Design an ID Numbering System section on page 47).
The HandPunch will not accept two people with the same ID number.
If you enroll people using the last four digits of their phone numbers or
social security numbers, you may get duplicate numbers.
If you are enrolling large groups of people you may consider using an
enrollment trainer. It is a replica of a platen that is available through your
Schlage Biometrics reseller.
If you are wearing a ring, rotate the ring so the stone faces up in its normal
position.
Slide your right hand onto the platen rather like an airplane landing at the
airport.
Slide your hand forward until the web between your index and middle finger
stops against the Web Pin.
Keep your hand flat. You should feel the surface of the platen on your palm
and the underside of your fingers.
Close your fingers together until they touch the Finger Pins and watch the
hand diagram light display on the top panel.
The lights go out when you have properly placed your fingers. If a light
remains on, a finger is not in proper contact with its Finger Pin.
HandPunch 3000/4000 Manual
WEB PIN
Figure 8-2: Placing Your Hand on the Platen
Left Hand
Enrollment
Some right hands cannot be used in the HandPunch due to disabilities such
as missing fingers. You can enroll a user with the left hand facing palm side
up. The techniques for left hand enrollment are the same as for standard
enrollment. The user should keep the back of the hand flat against the platen
and move the fingers against the web pin and the finger pins in the same
manner as in standard enrollment. Users enrolled with the left hand must
always verify with the left hand. Extra practice on placing the hand on the
platen may be required to ensure correct, consistent hand reads.
Read Score
When a user uses the HandPunch, the display appears as follows:
OKAY (USER ID)
SCORE IS: (SCORE NUMBER)
The score number on the display reflects how accurately the user’s hand is
placed on the platen (see page 64). Scores that vary greatly between low and
high numbers are indicative of inconsistent hand placement. Scores above
50 are indicative of improper hand placement or of a drastic change in the
physical appearance of the hand.
When this occurs, emphasize the importance of sliding the hand onto the
platen and keeping the hand flat. Re-training and practice should lower a
user’s score. It might be necessary to change a user’s reject threshold if the
user has a mild disability. Re-enrollment might be necessary to create a new
user template.
65
Programming the HandPunch
Enrollment
Commands
There are three commands available from the Enrollment command menu:
•
•
•
Add Employee
Add Supervisor
Remove User
Refer to Table 12 to identify the command you need to perform. Step through
all previous commands until you reach the desired command.
Table 12: Enrollment Command Menu
Service Menu
Password = 4
Add Employee
ID #
Add Supervisor
ID #
Remove User
ID #
Add
Employee
The Add Employee command allows you to enroll a new employee into the
HandPunch.
Add
Supervisor
The Add Supervisor command allows you to enroll a new supervisor into the
HandPunch.
Remove
User
The Remove User command allows you to remove an employee or supervisor
from the HandPunch.
66
HandPunch 3000/4000 Manual
Special Menu
The Special menu has one command – Special Enroll. This command
accommodates users with disabilities that make it difficult or impossible to
use a HandPunch in its standard way. The following section provides a brief
description of the Special Menu command.
Enter the appropriate password to enter the Special command menu. Once
you have entered the command menu, there are three options available for
navigating the command menu system.
Press # to enter the command shown on the display.
Press * to step to the next command in the menu.
Press CLEAR to exit the command menu (pressing any numeric key also
exits the command menu). If you are in a command’s sub-menu, press
CLEAR multiple times to completely exit the command menu.
Special Command
There is one command available from the Special command menu:
•
Special Enroll
Refer to Table 13 and identify the command you need to perform. Step through
all previous commands until you reach the desired command.
Table 13: Special Command Menu
Special Menu
Password = 5
Special Enroll
ID #
On/Off (Y/N)
67
Programming the HandPunch
Special Enroll The Special Enroll command allows a user to be enrolled such that the ID
number is the primary criteria for determining access. A hand read is required,
but is not verified against any stored identification data. A time zone value
can be applied to the Special Enrollment ID number to limit access times (see
page 62). The HandPunch default is for no time zone to be applied.
NOTE
68
Special Enrollment affects the integrity of the HandPunch terminal and should
only be used as a last resort. Anyone who knows a Special Enroll ID number
is granted access when the ID number is used. Before specially enrolling a
user, try to alleviate verification problems by adjusting the individual user’s
reject threshold (see page 62) or by using left hand enrollment (see page 65).
HandPunch 3000/4000 Manual
HandPunch Maintenance
A minimum amount of system maintenance is required to keep HandPunchs
fully functional. HandPunchs should be cleaned periodically to prevent an
accumulation of dust from affecting the HandPunch’s readability. User Scores
should be reviewed periodically to ensure the HandPunch is performing
properly.
NOTE
Cleaning the
HandPunch
There are NO user serviceable parts inside the HandPunch.
Once a HandPunch system is in operation there are three HandPunch
commands that can assist with system maintenance. These commands are
performed through the Service Menu. The instructions for these commands
begin on page 54.
•
•
Calibrate – View HandPunch exposure values.
Status Display – Display HandPunch input/output status, the hand read
score of the last user to verify on the system.
Inspect and clean the HandPunch regularly to maintain optimum performance.
Clean the platen, side mirror, reflector, and the window above the platen using
a clean cloth dampened with ordinary, non-abrasive window cleaner (see
Figure 9-1 below). Start at the rear corners of the platen and work your way
forward.
NOTE
DO NOT SPRAY CLEANING FLUID DIRECTLY INTO OR ON THE
HandPunch.
Figure 9-1: HandPunch Cleaning
User Score
Periodically check users’ scores (refer to the Read Score section on page
65). Scores should average under 30. Occasionally a user will score above
30. This is not necessarily an indication of poor performance. If a number of
scores average over 30, clean the HandPunch and check scores again. If
scores remain high, or if users are experiencing frequent rejections, run the
Calibration command (see page 55).
69
Appendix A - Tips
Appendix A
Tips for a successful Installation
HandPunch
•
•
•
•
•
•
Think of the HandPunch as a camera
Clean the HandPunch before it gets dirty
Use non-abrasive cleaners such as glass cleaners and non-abrasive and
clean cloths
Make cleaning the HandPunch part of Janitorial program
Do not remove the foam backing from the wall mounting plate
Seal any holes made in the wall for wire routing, so that dust will not blow
into the HandPunch
Location
•
•
•
•
Mount all HandPunchs in a network so that the top of the platen is 40” off
of the floor
If an enrollment HandPunch is used make sure that it is placed with the
top platen 40” off of the floor and not sitting directly on top of a desk, this
will help to eliminate “bad enrollments”
Mount the HandPunch so that it is not difficult or dangerous to verify then
open the door
It is not recommended to mount the HandPunch in an area where there is airborne dust, in the path of direct sunlight, or where the HandPunch can
be exposed to water or corrosive gasses
Enrollment
•
•
•
•
•
Educate the Enrollee on Hand Geometry
Explain enrollment process
Train Enrollee on hand placement
-Practice placing hand on platen
-Rotate rings to be stone-up
-Make sure hand is flat on platen
-Close finger towards the center of hand
-Fingers gently touch finger pins
Let the enrollee enter in their own ID number during the enrollment
process, this forces the Enroller to step aside allowing the Enrollee to
stand in front of the HandPunch helping to eliminate “bad enrollments”
If an enrollment HandReader is used make sure that it is placed with the
top of the platen 40” off of the floor and not sitting directly on top of a desk,
this will help to eliminate “bad enrollments”
• If an enrollment transaction fails:
-Retrain the user on correct placement and ensure that rings are rotated to be stone-up then
70
HandPunch 3000/4000 Manual
-Try again to enroll the same hand
-Try to enroll the other hand (with the hand placed upside-down so the thumb still contacts the thumb-pin on the platen)
• After enrollment, it is a good idea to let the enrollee enter their ID number
and practice a verification transaction to ensure that the enrollment was
high-quality.
• If a user consistently fails during verifications days/months/years later, reenroll the user to ensure a high quality and up-to-date enrollment record.
Communication
•
•
Make sure the Data Convertor is plugged in
When starting a network for the first time bring one HandPunch up at a
time, this is a very easy way to find out where communication problems
may exist
71
Appendix B - Board Configuration Differences
Appendix B
Noted Board Configuration Differences
Because of Schlage Biometrics’ camera retrofit of the HandPunch some
changes have been made to the main PCB and they are listed as follows:
• Dipswitches have been removed
-comm lines are terminated.
-RS-485 is set by wiring jumpers.
-memory is reset with a push-button reset and user interface with keypad and LCD.
• The labeling of the terminal strips have changed. See “Figure 11-1” on
page 73.
• The configuration of the terminal strips have changed. See “Figure 11-2”
on page 74.
• Power has moved to the right side of the PCB.
• The RSS-232 RJ-45 receptacle has been replaced with a 4 pin Molex connector on the left side of the PCB.
• A 2 pin Molex connector (J5) has been added to the board, next to the reset button, to supply power for the LEDs. This connector should never be unplugged. unless a modem or Ethernet is added to the PCB.
• The upgrading of the memory is now handled through software codes at the HandPunch. Contact Order Entry for memory upgrades.
72
HandPunch 3000/4000 Manual
Terminal
Block
Labeling
Number
1
2
RJ-11
RJ-11
RJ-11
RJ-11
OLD PCB
12-24 VDC (+) OR VAC
12-24 VDC (-) OR VAC
RXRX+
TXTX+
7
8
9
10
11
12
13
14
REX SWITCH
GROUND
DOOR SWITCH
GROUND
AUX IN 1
GROUND
AUX IN 2
GROUND
15
16
17
18
19
20
21
22
23
24
25
26
(+) 5 VDC OUTPUT
DATA/D0
CLOCK/D1
GROUND
LOCK OR CLOCK OUTPUT
GROUND
BELL OR DATA OUTPUT
GROUND
AUXOUT 1
GROUND
AUXOUT 2
GROUND
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RJ-11
RJ-11
RJ-11
RJ-11
1
2
NEW PCB
(+) 5 VDC OUTPUT
DATA/D0
CLOCK/D1
GROUND
LOCK OR CLOCK OUTPUT
BELL OR DATA OUTPUT
AUXOUT 1
AUXOUT 2
REX SWITCH
GROUND
DOOR SWITCH
AUX IN 1
GROUND
AUX IN 2
RXRX+
TXTX+
12-24 VDC (+) OR VAC
12-24 VDC (-) OR VAC
Figure 11-1
73
Appendix B - Board Configuration Differences
Terminal
Block
Layout
New Board
Old Board
J6
1
1
2
2
J6 - 2 pin Power
connector when
daisy chaining
power to
HandReaders
RJ-11 - 4 pin Comm
connector
7
TS2
8
9
9
10
10
11
11
12
12
13
13
14
TS2 - 6 pin Input
connector
14
15
16
TS3
17
1
18
2
19
3
20
4
21
5
22
6
23
7
24
8
TS3 - 8 pin Output
connector
25
26
7
8
Any of the grounds coming off
of pins 8, 10, 12, 14, 18, 20,
22, 24, and 26 of the "Old
Board" can be tied to pin 4, 10,
or 13 on the new board. If
there are multiple grounds
create a pig tail so that there is
only 1 wire going into the
terminal block
Figure 11-2
74
9
10
11
12
13
14
9
GRD
GRD
GRD
GRD
10
11
12
GRD
GRD
Example of Ground Pigtail
13
14
HandPunch 3000/4000 Manual
Memory
Reset
To reset the memory of the HandPunch follow these steps1. Remove power and battery jumper, if a back up is installed
2. Press down on reset button and apply power
3. Release button
4. Reader will boot to
ERASE
•
•
:1 SETUP
:9 ALL!!!
Press 1 to erase setup i.e. address, outputs, passwords, but retain user database and datalogs
Press 9 to erase everything i.e. HandPunch goes back to factory defaults
75
Appendix C - Old Board Configuration
Appendix C
Old Board Configuration Information
Wall Plate Installation
1. Loosen the three bottom mounting screws until there is approximately 1/8 inch (3 mm) clearance between the screw head and the wall plate.
2. Remove the HandPunch from its carton.
3. At the base of the HandPunch is a piano hinge with three keyhole shaped
slots that correspond with the three lower mounting screws. Align and hang the HandPunch from the three lower mounting screws (see below).
HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
KEYHOLE
HOLES
3 LOWER
MOUNTING
SCREWS
REAR OF TERMINAL
Figure 13-1: Attaching the HandPunch to the Wall Plate
4. Tighten all three lower mounting screws.
5. The HandPunch is now ready for its wiring connections.
76
HandPunch 3000/4000 Manual
Grounding
Terminal 1 and the center pin of jack J12 are connected together. Terminal 2 and
the sleeve of jack J12 are connected together.
Use any one of the following ground terminals to make the earth ground
NOTE connection: 8, 10, 12, 14, 18, 20, 22, 24, or 26. Do NOT use terminal 2 to
establish the earth ground connection; terminal 2 is not directly connected to
ground.
NOTE
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8
7
SWITCH INPUTS
CARD
READER
INPUT
OUTPUTS
AUXOUT 2
GROUND
AUXOUT 1
GROUND
BELL OR DATA
GROUND
GROUND
LOCK OR CLOCK
GROUND
CLOCK INPUT
DATA INPUT
+5 VDC OUTPUT
GROUND
AUX IN 2
GROUND
AUX IN 1
DOOR SWITCH
GROUND
GROUND
REX SWITCH
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
EARTH GROUND
CONNECTION PINS
Figure 13-2: Earth Ground Connection Terminals
There are two standard methods for providing earth grounding to HandPunch
units:
• earth grounding all units (see 15)
• carrying an earth ground to each unit (see 16)
Earth ground all units when there is a good earth ground source near each unit
and/or when there are very long cable runs between units.
Carry an earth ground to each unit when there are no earth grounds convenient
to the unit and the unit’s power supply is floating.
77
Appendix C - Old Board Configuration
Wiring Connections
Once the HandPunch is attached to the wall plate the wiring connections to the
HandPunch can be made (see Figure 13-3 below).
Wall Plate
WALL
8 1 26
RS-232 RJ-45
TS-3 Terminals 26 to 15
TS-2 Terminals 14 to 7
15 14
76
1
Backup Battery
Jumper
Optional Modem
or Ethernet Jack
TS-1 Terminals 6 to 1
Top of Hand Reader
Top of
Terminal
5 4 3 2 1 OFF
ON
Dip Switches
Figure 13-3: Wiring Connections and Dip Switches
Wiring Examples
The following Tables provide the pin outs for the terminal strips on the
HandPunch.
•
•
•
•
“Table 14” on page 79 provides the pinouts for TS-2 – Input Connections.
“Table 15” on page 79 provides the pinouts for TS-3 – Card Reader and Output
Connections.
“Table 16” on page 80 provides the pinouts for the RJ-45/RS-232 Serial Printer
or Host Computer Connection.
“Table 17” on page 81 provides the pinouts for the RJ-11/RS-422 HandPunchto-HandPunch Network Connection.
The following Figures provide pinout diagrams for the RJ connectors.
• Figure 13-4 on 81 provides the pinouts for J3, the RJ-11/RS-422 Network Connection.
• “Figure 13-5” on page 81 provides the pinouts for J8, the RJ-45/RS-232 Serial
Printer Connection.
78
HandPunch 3000/4000 Manual
The following Figures provide sample HandPunch wiring diagrams:
• “Figure 13-6” on page 82 provides a sample Bell Output wiring diagram.
• “Figure 13-7” on page 83 provides a sample Door Lock Output wiring diagram.
• “Figure 13-8” on page 84 provides a sample Request to Exit, Door Switch, and Auxiliary Inputs wiring diagram.
• “Figure 13-9” on page 85 provides a sample Auxiliary Outputs wiring diagram.
• “Figure 13-10” on page 86 provides a sample External Card Reader wiring diagram.
• “Figure 13-11” on page 87 provides a sample RS-422 4-Wire Direct-
Connect Host PC to HandPunch Network wiring diagram.
• “Figure 13-12” on page 88 provides a sample Host PC to HandPunch Ethernet Network wiring diagram.
• “Figure 13-13” on page 89 provides a sample Host PC to HandPunch Modem Network wiring diagram.
• “Figure 13-14” on page 90 provides a sample Printer or Host PC to HandPunch wiring diagram.
Table 14: TS-2 - Input Connections
Terminal
Connection
7
Request to Exit Input
8
Ground
9
Door Monitor Switch Input (NC Standby)
10
Ground
11
Auxiliary Input 1
12
Ground
13
Auxiliary Input 2
14
Ground
Table 15: TS-3 - Card Reader and Output Connections
Terminal
Connection
15
+5 VDC @ 400 mA Max. Output for External Card Reader
16
Card Reader: Wiegand D0 or Magnetic Stripe Data Input
79
Appendix C - Old Board Configuration
Table 15: TS-3 - Card Reader and Output Connections
Terminal
Connection
17
Card Reader: Wiegand D1 or Magnetic Stripe Clock Input
18
Card Reader Ground
19
Lock Output or Wiegand D1 or Magnetic Stripe Clock Output
20
Ground
21
Auxiliary Output 0 or Wiegand Data 0 or Magnetic Stripe Data Output
22
Ground
23
Auxiliary Output 1
24
Ground
25
Auxiliary Output 2
26
Ground
Table 16: RJ-45/RS-232 Serial Printer Connection
J8 Pin
Signal
Connection
1
RI
* Ring Indicator Input
(from external device)
2
CD
* Carrier Detect Input
(from external device)
3
DTR
* Data Terminal Ready Output (to external device)
4
GND
Ground
5
Rx Data
Receive Data Input (from external device)
6
Tx Data
Transmit Data Output (to external device)
7
CTS
* Clear to Send Input (from external device)
8
RTS
* Ready to Send Output (to external device)
* These signals are not currently supported
80
HandPunch 3000/4000 Manual
Table 17: RJ-11/RS-422 Network Connection
J3 Pin
Signal
1
Rx+
2
Rx-
3
Tx-
4
Tx+
J3 Pins
1 2 3 4
Figure13-4: J3 - RJ-11/RS-422 Jack Pinout
J4 Pins
1 2 3 4 5 6 7
Figure 13-5: J4 - RJ-45/RS-232 Jack Pinout
81
Appendix C - Old Board Configuration
POWER SUPPLY
+
1
2
NC
12 to 24 VDC Max.
NO
BELL
1
1
BELL
RELAY
WALL TO WHICH
THE HAND PUNCH
IS ATTACHED
HINGE
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
RJ-45/RS-232
Printer Output
7
Optional RJ-45
Ethernet or
RJ-11 Modem
Power
Connection
These components are not supplied by Recognition Systems, Inc.
2
The Power Supply shall be a UL Listed Limited Current
Power Source for UL 294 Installations.
Figure 13-6: Bell Output Wiring Diagram
82
8
RJ-11/RS-422
4-wire
Network
TOP OF THE
HANDPUNCH
1
9
HandPunch 3000/4000 Manual
1
POWER SUPPLY
+
12 to 24 VDC Max.2
NC
NO
ELECTRIC LOCK1
+ OR STRIKE -
1
LOCK
RELAY
WALL TO WHICH
THE HAND PUNCH
IS ATTACHED
HINGE
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
RJ-45/RS-232
Printer Output
9
7
RJ-11/RS-422
4-wire
Network
TOP OF THE
HANDPUNCH
1
8
Optional RJ-45
Ethernet or
RJ-11 Modem
Power
Connection
These components are not supplied by Recognition Systems, Inc.
2
The Power Supply shall be a UL Listed Limited Current
Power Source for UL 294 Installations.
Figure 13-7: Door Lock Output Wiring Diagram
83
1
2
N.C. DOOR SWITCH
N.O. MOMENTARY
1
AUX INPUT 1
N.C. DOOR SWITCH
AUX INPUT 2
2
SWITCH LEGEND
N.O. REQUEST TO EXIT
Appendix C - Old Board Configuration
WALL TO WHICH
THE HAND PUNCH
IS ATTACHED
HINGE
14 13 12 11 10 9
8
7
6
5
4
3
2
1
RJ-11/RS-422
Network
Power
Connections
TOP OF THE
HANDPUNCH
1
2
RS-232
Printer Output
Optional RJ-45
Ethernet or
RJ-11 Modem
These components are not supplied by Recognition Systems, Inc.
The Aux 1 and Aux 2 input contact states are programmable within
the HandPunch unit.
Figure 13-8: Request to Exit, Door Switch, and Auxiliary Inputs Wiring Diagram
84
HandPunch 3000/4000 Manual
1
POWER SUPPLY
+
12 to 24
VDC Max.2
NC
NO
1
AUXILIARY
+
DEVICE
1
AUX OUTPUT 0
AUX OUTPUT 1
AUX OUTPUT 2
AUX.
RELAY
WALL TO WHICH
THE HANDPUNCH
IS ATTACHED
HINGE
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
RJ-45/RS-232
Printer Output
8
7
RJ-11/RS-422
4-wire
Network
TOP OF THE
HANDPUNCH
1
9
Optional RJ-45
Ethernet or
RJ-11 Modem
Power
Connection
These components are not supplied by Recognition Systems, Inc.
2
The Power Supply shall be a UL Listed Limited Current
Power Source for UL 294 Installations.
Figure 13-9: Auxiliary Outputs Wiring Diagram
85
Appendix C - Old Board Configuration
ABA-Track II
Magnetic Stripe Card Reader
AUX INPUT 1 2
AUX INPUT 2
AUX OUTPUT 1
AUX OUTPUT 2
2
CLOCK
GROUND
DATA
REQUEST TO EXIT
Access Control
Panel
N.C. DOOR SWITCH
GROUND
CLOCK
DATA
+5 VDC POWER
(SEE NOTE BELOW)
SWITCH LEGEND
N.C. DOOR SWITCH 1
N.O. MOMENTARY
1
WALL TO WHICH
THE HANDPUNCH
IS ATTACHED
HINGE
J6
+12 VDC for
12 Volt External
Card Readers
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7
RJ-45/RS-232
Printer Output
RJ-11/RS-422
4-wire
Network
TOP OF THE
HAND READER
1
2
Optional RJ-45
Ethernet or
RJ-11 Modem
HandPunch
Power
Connection
These components are not supplied by Recognition Systems, Inc.
The Aux 1 and Aux 2 input contact states are programmable within
the HandPunch unit.
NOTE: For +12 VDC magnetic stripe readers, connect the magnetic stripe reader
power supply to J6 on the Hand Punch.
Figure 13-10: External Card Reader Wiring DIagram
86
HandPunch 3000/4000 Manual
DC-102
RS-232 to 4-wire RS-422
Power Supply Data Converter (P/N DC-102)
B
DB-25
Serial
Port
Recognit
ion
1
2
4
5
7
8
*
No
0
3
6
9
* RS-422
4-Wire
(2 Twisted
Pairs)
RJ-11 Jack Surface
or Wall Plate
Inc.
Clear
F1
F2
#
No
Yes
Systems
Enter
B
HandPunch 1
Recognit
ion
1
4
7
*
No
2
5
8
3
6
9
0
Systems
* RS-422
4-Wire
(2 Twisted
Pairs)
Inc.
Clear
F1
Enter
HandPunch 2
Recognit
ion
1
4
*
No
0
2
5
8
3
6
9
Systems
G
Y
J-3
* RS-422
4-Wire
(2 Twisted
Pairs)
Inc.
Clear
F1
Enter
B
HandPunch X
R
G
Y
J-3
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
R
F2
#
No
Yes
Y
G
J-3
B
7
R
F2
#
No
Yes
R
Y
G
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 13-11: RS-422 4-Wire Direct-Connect Host PC to HandPunch Connection
87
Appendix C - Old Board Configuration
Ethernet Cable
Recogniti
on
1
4
7
*
No
2
5
8
0
3
6
9
Clear
F1
F2
#
No
Yes
Connection to
Host Computer
via Ethernet
HandPunch
Ethernet Port
Systems
Inc.
Enter
HandPunch
RS-422
RJ-11 Port
Ethernet Unit
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
RJ-11 Jack Surface
or Wall Plate
Recogniti
on
1
2
4
5
7
8
*
No
0
3
6
9
Inc.
F2
#
No
Yes
Systems
Clear
F1
Enter
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
HandPunch 1
Recogniti
on
1
4
7
*
No
2
5
8
3
6
9
0
Inc.
F1
F2
#
No
Yes
Systems
Clear
Enter
B
R
G
Y
HandPunch 2
Recogniti
on
1
4
7
*
No
8
0
2
5
6
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
* RS-422
4-Wire
(2 Twisted
Pairs)
Enter
B
R
G
Y
HandPunch X
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 13-12: Host PC to HandPunch Ethernet Connection
88
HandPunch 3000/4000 Manual
RSI Supplied Cable (Black)
Recogniti
on
1
4
7
*
No
5
8
0
2
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
6
Enter
Modem Unit
HandPunch
Modem Port
RJ-11 Telephone Outlet
HandPunch RS-422
RJ-11 Port
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
RJ-11 Jack Surface
or Wall Plate
Recogniti
on
1
2
4
5
7
8
*
No
0
3
6
9
F1
F2
#
No
Yes
Systems
Inc.
Clear
Enter
B
R
G
Y
* RS-422
4-Wire
(2 Twisted
Pairs)
HandPunch 1
Recogniti
on
1
4
7
*
No
2
5
8
3
6
9
0
F1
F2
#
No
Yes
Systems
Inc.
Clear
Enter
B
R
G
Y
HandPunch 2
Recogniti
on
1
4
7
*
No
5
8
0
2
6
9
Systems
Inc.
Clear
F1
F2
#
No
Yes
3
* RS-422
4-Wire
(2 Twisted
Pairs)
Enter
B
R
G
Y
HandPunch X
RSI Supplied Cable
(Silver)
* Recommended Cable
Belden #82723
B = Black
R = Red
G = Green
Y = Yellow
To Next HandPunch
31 HandPunches Max
4,000 Ft. (1220 meters)
Max Zone Length
Figure 13-13: Host PC to HandPunch Modem Connection
89
Appendix C - Old Board Configuration
RJ-45 to Printer
Adapter
(if required)
*Serial Printer
WALL TO WHICH
THE HAND READER
IS ATTACHED
RJ-45
Connector
HINGE
RJ-45
Connector
12 to 24 V
AC/DC
Input
TS-3
TS-2
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
J4
RJ-45 Jack
TS-1
9
8
7
6
5
4
3
RS-422
Connection
2
TOP OF THE
HAND READER
* These components are not supplied by Recognition Systems, Inc.
Figure 13-14: HandPunch to Serial Printer or Host Computer Wiring Diagram
90
1
- +
HandPunch 3000/4000 Manual
Setting the DIP Switches
The DIP Switch settings perform three tasks for the HandPunch (see Figure
13-15 below):
• Set End of Line (EOL) Termination to match the type of termination needed by the network.
• Set the Communication Method to match the type of network used.
• Erase Memory to clear HandPunch memory to all factory defaults values and also clear all user memory.
WA L L
5 4 3 2 1
OFF
ON
E O L Te r m i n a t i o n
E O L Te r m i n a t i o n
Communication Method
Erase HandReader Setup
Erase HandReader Setup and Database
TOP OF HANDREADER
Figure 13-15: HandPunch Dip Switches
91
Appendix C - Old Board Configuration
End of Line
Termination
Termination helps to ensure clean data signals are transmitted through the
network wiring. Termination is applied to the end-of-line (EOL) HandPunch
in the network daisy-chain. The factory default setting is for EOL termination
to be disabled – switches 1 and 2 OFF. Refer to “Figure 13-15” on page 91 for
switch ON/OFF positioning.
•
•
To enable EOL termination at a HandPunch, both switches 1 and 2 must be ON.
To disable EOL termination at a HandPunch, both switches 1 and 2 must be OFF.
EOL Termination must be enabled for:
• A single HandPunch terminal installation.
• In a HandPunch Direct-Connect network – the last HandPunch in the daisy-chain (the one farthest from the host computer).
• In a Modem/HandPunch to PC network the HandPunch terminal with the
Ethernet option (for communication with the host computer) in the daisy-
chain.
EOL Termination must be disabled for:
• All HandPunches in the network not identified in teh previous section.
• In an Ethernet/HandPunch to PC network the HandPunch terminal with
the Ethernet option (for communication with the host computer) in the daisy-chain.
Communication Method
The communication method dip switch is set ON for factory testing purposes.
The factory default setting and for standard operation, switch 3 must be OFF.
• Switch 3 must always be OFF.
Erasing HandPunch Memory
The erase memory function can perform either or both of the following:
• Erase a HandPunch’s configuration data.
• Erase a HandPunch’s user database, transaction buffer, and menus (and messages on the HandPunch 4000).
The factory default setting (and normal operation setting) is set for switches 4
and 5 to be OFF, retaining memory.
NOTE
92
If the HandPunch is equipped with the battery backup option, remove shunt
J7 in front of the DIP switch array (see “Figure 13-3” on page 78) before
proceeding. Replace shunt J7 after completion of the following steps.
HandPunch 3000/4000 Manual
Erasing the
HandPunch
Setup
Perform the following steps to erase the configuration data but retain the
user database.
1. With system power OFF, set switch 4 ON.
2. Turn system power ON and wait for HandPunch boot information to
appear on the display.
3. Turn switch 4 OFF.
Erasing the
HandPunch
Setup and
User Database
NOTE
Perform the following steps to erase both the configuration data and the user
database.
1. With system power OFF, set both switches 4 and 5 ON.
2. Turn system power ON and wait 5 seconds.
3. Turn both switches 4 and 5 OFF.
Before putting the HandPunch into service ensure DIP switches 4 and 5 are
both OFF. If switches 4 and 5 are not off, the next time the HandPunch’s
power is cycled the HandPunch’s memory will be erased.
93
Appendix D - Troubleshooting Tips
Appendix D
Troubleshooting Guide
Display Messages During Verification
Various messages can appear on the HandPunch’s dispaly during
hand verification. These messages are defined in Table 18 below.
Table 18: Display Messages During Verification
Message
PLACE HAND
ID VERIFIED
REMOVE HAND
Definition
The platen is ready to receive your hand for verification.
You are verified, proceed.
Remove your hand and place it on the platen again.
Follow proper hand placement rules.
TRY AGAIN
Your attempt was rejected. Repeat verification following
proper hand placement rules.
ID REFUSED
Your rejections exceeded the maximum number of tries
allowed. Wait until another employee has verified and try
again or call your supervisor.
ENTER ID
You entered your ID number incorrectly or your access
time is restricted.
If the display shows TRY AGAIN, you are not verified. You may have made
an error in entering your ID number or in placing your hand on the platen.
Re-enter your ID number and try again, taking care to follow proper hand
placement rules (see 64).
• If the display shows TIME RESTRICTION, you are not authorized to punch
in at this time. If this seems to be in error, contact your supervisor about time
restrictions.
• After a pre-programmed number of denied attempts, an ID number will no
longer be accepted and the display will appear as follows:
•
ID INVALID
TEMPORARILY
94
HandPunch 3000/4000 Manual
This is called a “lockout”. Before the rejected ID number can be used again,
another employee or a supervisor must successfully verify at the HandPunch.
•
If you enter your ID number, but do not place your hand on the platen, the
HandPunch will time-out in about 25 seconds. You can immediately end
this time-out by the CLEAR key.
Beeper and LED Status During Verification
The HandPunch’s beeper and LED status display also displays hand
verification information. This information is defined in Table 19 below.
Operation
During Keypad
Entry
After ID Entry
After ID Entry
After Hand
Placement
After Hand
Placement
After Hand
Placement
Table 19: Beeper and LED Status During Verification
Beeps
1 per Keystroke
LED
–
–
2
–
–
1
Green
2
Red
1 Long
Continuous
Red
Meaning
Keystroke
Accepted
OK - Proceed
ID Number Not in
Database
ID Verified
ID Not Verified Try Again
ID Refused
95
Glossary
Glossary
Address, IP – An Internet Protocol address is a unique address assigned to a
computer for communicating over a LAN/WAN. It is made up of 4 sets of numbers,
separated by periods (for example, 123.245.78.901).
Address, HandPunch – A HandPunch Address is a unique identification number
assigned to a HandPunch. Each HandPunch on a site must be assigned its own
unique address.
AWG – American Wire Gauge is a U.S. standard set of wire conductor sizes. The
“gauge” refers to the diameter of teh wire. The higher the gauge number, the
smaller the diameter, the thinner the wire, and teh greater the electrical resistance.
Thicker, smaller gauge wire carries more current because it has less electrical
resistance over a given length. Thicker wire is better for long wire distances.
Daisy-Chain – A Daisy-Chaing is a method of wiring together HandPunch on a
network, where the first HandPunch is connected to the second HandPunch,
which is connected to the third HandPunch, and so on until the last HandPunch is
reached.
End-of-Line (EOL) Termination – EOL Termination is a set of resistors attached to
the data lines at the last HandPunch physically connected to a network. These
resistors prevent data signal distortion and reflection back across the data lines,
improving the integrity of the network connection.
HandPunch Address – see Address, HandPunch.
IP Address – see Address, IP.
Platen – The Platen is the flat surface at the base of the HandPunch, on which a user
places his/her hand for enrollment and verification. The platen has guide pins to
ensure the user’s fingers are consistently positioned correctly.
Template – A Template is a set of data generated for a user. It is made up of the user’s
enrollment information and any system configuration parameters that are assigned
to the user. The template is stored at each HandPunch and can be stored at the
host computer with the Time and Attendance software.
Time Zone – A Time Zone is an identified period of time, during which a user is
allowed to punch in our out at a HandPunch. Punch attempts outside of that time
period are rejected by the HandPunch.
Transaction – A Transaction is any kind of event recorded at a HandPunch.
Transactions may include In or Out punches, department transfers, and supervisor
edits.
96
HandPunch 3000/4000 Manual
Wiegand™ Reader – The term “Wiegand Reader” has two meanings depending upon
its application. A true Wiegand reader reads a specially constructed card made
up of small pieces of magnetic wire. As the card is swiped through the reader, the
individual bits of wire generate a unique data signal. This data signal is made up
of a Facility Code field (typically 8 bits), an ID number field (typically 16 bits), and
parity bits (typically 2 bits) for a total of 26 bits of data. Now this 26-bit Wiegand
data format has been adopted by a variety of card reader devices for entering user
ID data. Other Wiegand formats (for example, 37-bit) are used as well.
97
Warranty
Limited Warranty
Schlage Biometrics, Inc. (the “Company”) warrants to the original user the
products manufactured by the Company (the “Product”) to be free of defects in
material and workmanship for a period of one year from the date of purchase by
usch user or 15 months from the date of shipment from the factory, whichever is
sooner, provided:
1. The Company has been notified within such period by return of any alleged
defective product, free and clear of all liens and encumbrances, to the Company
or its authorized dealer, transportation prepaid; and
2. The Product has not been abused, misused, or improperly maintained and/or
repaired during such period; and
3. Such defect has not been caused by ordinary wear and tear; and
4. Such defect is not the result of voltage surges/brownouts, lightning, water
damage/flooding, fire, explosion, earthquakes, tornadoes, acts of aggression/war,
or similar phenomenon; and
5. Accessories used as integral to the Product have been approved by the
Company.
The Company shall, at its option, either repair or replace, free of charge, the
Product found, upon the Company’s inspection, to be so defective, or if agreed
upon, refund the purchase price, less a reasonable allowance for depreciation, in
exchange for the Product.
THE COMPANY MAKES NO OTHER WARRANTY AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION
OF THE EXPRESSED WARRANTY PERIOD AS SET FORTH ABOVE.
THE COMPANY’S MAXIMUM LIABILITY THEREUNDER IS LIMITED TO THE
PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, INCIDENTAL, OR
SPECIAL DAMAGES OF ANY NATURE ARISING FROM THE SAME OR THE
USE OF THE PRODUCT.
Schlage Biometrics, Inc. reserves the right to make changes in the design of any
of its products without incurring any obligation to make the same change on units
previously purchased.
98
Ingersoll Rand’s Security Technologies Sector is a leading global provider of products and services that
make environments safe, secure, and productive. The Sector’s market-leading products include electronic
and biometric access control systems; time and attendance and personnel scheduling systems; mechanical
locks and portable security, door closures and exit devices, steel doors and frames, architectural hardware
and technologies and services for global security markets.
866.861.2480
Schlage
Biometric Solutions
Ingersoll Rand Security Technologies
538 Oakmead Parkway
Sunnyvale, CA 94085
Office: 866-861-2480/512-712-1413 (international)
Fax: 866-303-1794/408-341-4101
E-mail: sbssupport@irco.com
www.schlage.com
©2011 Ingersoll-Rand Company Limited
www.ingersollrand.com
P/N 70100-6003 Rev. 3.3 07/11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising