error reference

error reference
EDIABAS - ERROR REFERENCE
EDIABAS
Electronic Diagnostic Basic System
ERROR REFERENCE
VERSION 6b
Copyright BMW AG, created by Softing AG
ERROR.DOC
EDIABAS - ERROR REFERENCE
Contents
Contents ..........................................................................................................2
1.
Revision history .....................................................................................3
2.
Introduction ............................................................................................4
3.
4.
2.1.
About this manual....................................................................4
2.2.
Notational conventions ............................................................4
2.3.
Special features, terms, acronyms ..........................................5
General Information ...............................................................................6
3.1.
Error symbol and error code....................................................6
3.2.
Message and output of an error ..............................................6
3.3.
How errors affect program execution ......................................7
List of errors ...........................................................................................8
4.1.
IFH, Interface Handler .............................................................9
4.2. Runtime system ...............................................................................34
4.2.1. BIP, BEST Interpreter ...........................................................34
4.2.2. SYS, sequence control .........................................................41
4.3. API, Application Programming Interface .........................................55
A.
4.4.
Network ...................................................................................64
4.5.
Applikation...............................................................................72
References..............................................................................................73
2
EDIABAS - ERROR REFERENCE
1.
Revision history
Version 3.0
First release
Version 3.0A
Enhanced error message descriptions (partially)
Version 3.0B
Enhanced error message descriptions (complete)
Version 4.1
Revised for EDIABAS V4.1.0
Version 5
Revised for EDIABAS V5.1.0
Version 5a
Error corrections
Extended for EDIABAS 5.5.0
Version 5b
New: IFH-0037 to IFH-0040
Version 5c
Extended for QNX
Version 6
Extended for EDIABAS 6.0.0: BIP-0012, BIP-0013 and IFH-0041
to IFH-0059
Version 6b
Revised for EDIABAS V6.4.4
3
EDIABAS - ERROR REFERENCE
2.
Introduction
2.1. About this manual
This manual describes the general structure of an error. All errors which can occur in
EDIABAS are listed, including the respective methods of correction. General
information regarding EDIABAS and ECU description files is described in [2].
2.2. Notational conventions
The following typographical conventions are used throughout this manual:
Example
SAMPLE.C
Description
Uppercase denotes file names, registers and
operating system commands.
Bold-faced type identifies keywords and operators of
apiJob,
the language BEST/2 and BEST/s as well as the
APIREADY
API functions.
These words must be written exactly as specified in
syntax descriptions.
expression
Italics designate placeholders for values to be
entered by the programmer; e.g., file names..
[option]
Words enclosed in square brackets may be
optionally specified.
Curvy braces and vertical strokes characterize
{ result |
entries from which only one must be selected,
argument }
except when in square brackets.
[constant...] job... An ellipsis (three dots) which directly follows an
expression indicates that several expressions of the
same type can follow.
hallo="Test"; This syntax designates examples, user entries,
program outputs and error messages.
while() {
A column or a row comprising three dots indicates
.
that a section of an example was intentionally
.}
omitted.
[1]
Reference to a document in References.
4
EDIABAS - ERROR REFERENCE
2.3. Special features, terms, acronyms
An explanation of all abbreviations used in this and all other EDIABAS documentation
can be found in the publication "EDIABAS User Manual" in chapter "GLOSSARY"
5
EDIABAS - ERROR REFERENCE
3.
General Information
Erroneous functions such as time-out during ECU communication can occur during
the execution of EDIABAS. An erroneous function recognized by EDIABAS is
reported as an EDIABAS error.
3.1. Error symbol and error code
An error symbol structured as follows is assigned to each error:
The Origin of an error denotes the EDIABAS-internal program area where the error
was detected. The following areas are possible:
IFH
BIP
SYS
API
NET
RUN
Interface Handler (run-time system)
BEST Interpreter (run-time system)
Run-time System (run-time system)
Application Programming Interface
Network (run-time system)
SGBD (ECU description file)
Errors having the same Origin can be differentiated using a 4-digit error number. If an
error does not exist, it is identified by the pseudo error symbol
EDIABAS_ERR_NONE.
An integer value, the error code, is assigned to each Error symbol. The value 0
indicates that an error was not recognized by EDIABAS (error symbol
EDIABAS_ERR_NONE).
3.2. Message and output of an error
An error recognized by EDIABAS is reported to the application program and can only
be output there.
6
EDIABAS - ERROR REFERENCE
An application program can independently determine the type and way an error is
handled, whereby basically only the following error information can be fetched by
EDIABASE:
Error code
( with API function apiErrorCode )
Error text
( with API function apiErrorText )
Document [1] describes, in detail, the procedure on how an application program
recognizes and issues (outputs) errors.
3.3. How errors affect program execution
An error which occurs while a job is being processed causes the job to be aborted
and an error message to be issued to the application program. All job results stored
up to this point are deleted. If an error occurs during the initialization of EDIABAS
(apilnitXxx) by the application program, initialization is aborted.
An error remains stored until an application program (apiJobXxx call) starts a new
job, re-initialization is performed via apiInitXxx, or a device change is performed with
apiSwitchDevice.
The errors API-0005 and API-0014 will be deleted during the next result query
(apiResultXxx).
7
EDIABAS - ERROR REFERENCE
4.
List of errors
This chapter lists all errors which are reported by EDIABAS. In accordance with the
place of origin, subdivision into IFH, BIP, SYS and API is made.
All errors are represented in the same way:
Error symbol
Error code Error text
Meaning:
Causes:
Error correction:
Target system
WIN
SCO
QNX
Error code represents the error (as a value) reported by EDIABAS. This value can
be fetched by the application from EDIABAS using the function apiErrorCode.
Error text shows the error reported by EDIABAS in text format. This error text can be
fetched by the application program from EDIABAS using the function apiErrorText.
Error symbol corresponds to the error assignment in file API.H, in which the error
symbol is defined as a constant.
Each error description comprises the sections Meaning, Causes, Error correction
and Target system. Errors are explained in section "Meaning". The causes of an
error are described in a corresponding section. All measures described in section
"Error correction" are always to be observed or carried out.
Section "Target system" informs the user under which EDIABAS target system the
error can occur. If an error cannot occur on an EDIABAS target system, the
corresponding target system is crossed out.
Each target system is assigned an:
„ WIN
=
EDIABAS / MS-WINDOWS
„ SCO =
EDIABAS / SCO UNIX
„ QNX =
EDIABAS / QNX
8
EDIABAS - ERROR REFERENCE
4.1. IFH, Interface Handler
10
IFH-0000: INTERNAL ERROR
EDIABAS_IFH_0000
Meaning:
This error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
11
WIN
SCO
QNX
EDIABAS_IFH_0001
IFH-0001: UART ERROR
Meaning:
Overflow of a data buffer in the device driver of the
interface or undefined error message from the driver.
Causes:
More data are sent to the driver than this buffer can
receive.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
WIN
SCO
QNX
9
EDIABAS - ERROR REFERENCE
12
IFH-0002: NO RESPONSE FROM
INTERFACE
EDIABAS_IFH_0002
Meaning:
The diagnostic bus interface connected does not
respond.
Causes:
The interface is not connected.
The interface is not supported by the Interface Handler
No voltage is supplied to the interface.
No firmware is loaded in the interface (download
version of the interface).
Error correction: Check if the correct interface is properly connected.
Target system:
13
WIN
SCO
QNX
IFH-0003: DATATRANSMISSION TO
INTERFACE DISTURBED
EDIABAS_IFH_0003
Meaning:
A response from the interface was incorrectly received
(characters were lost, protocol frame incorrect, etc.).
Causes:
Contact problems in the cables between the host
system and EDIC-GH.
Error correction: Check the cables between the host system and EDICGH.
Target system:
WIN
SCO
QNX
10
EDIABAS - ERROR REFERENCE
14
IFH-0004: ERROR IN INTERFACE
COMMAND
EDIABAS_IFH_0004
Meaning:
Unknown command to the interface.
Causes:
The requested interface function is not available in the
interface used.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
15
WIN
SCO
QNX
IFH-0005: INTERNAL INTERFACE
ERROR
EDIABAS_IFH_0005
Meaning:
This error indicates an illegal program status of the
diagnostic bus interface.
Causes:
A program result of the interface cannot be processed.
Error correction: If an error repeatedly occurs, temporarily interrupt its
voltage supply in order to reset the interface.
If an error still occurs after interrupting of the voltage
supply, re-load the firmware of the interface.
Please contact SOFTING if the error still continues to
occur.
Target system:
WIN
SCO
QNX
11
EDIABAS - ERROR REFERENCE
16
IFH-0006: COMMAND NOT ACCEPTED
EDIABAS_IFH_0006
Meaning:
The interface fails to accept the sent command.
Causes:
With diagnostic bus interface EDIC:
A "Send message to ECU" (BEST1: xsend; BEST2:
send_and_receive) or "Set ECU parameters" (BEST1:
xsetpar; BEST2: set_communication_pars) was sent to
EDIC while ECU communication is still in progress. If
cyclic sending of a message is started (BEST1: xsendf;
BEST2: send_frequent), ECU communication is
continuously active.
Error correction: This mode must be aborted prior to re-sending a
message or setting ECU parameters (BEST1: xstopf;
BEST2: stop_frequent).
Target system:
17
WIN
SCO
QNX
EDIABAS_IFH_0007
IFH-0007: WRONG UBATT
Meaning:
This error occurs when either no voltage is currently
supplied to the D bus or when the voltage is too small.
In addition, this error can also be caused by short
circuits on the D bus. The error message is issued only
following BEST commands which access the D bus.
These are:
Send and receive a message
Request the ECU keybytes and identification
data
This error message is suppressed for all other BEST
commands of the Interface Handler (e.g. read the ports
or set ECU parameters). As soon as the correct voltage
is applied on the D bus, an error message no longer
occurs after executing the BEST commands above.
Causes:
No (or too small) voltage supplied on the D bus.
Error correction: Supply voltage to the D bus.
Target system:
WIN
SCO
QNX
12
EDIABAS - ERROR REFERENCE
18
IFH-0008: CONTROLUNIT CONNECTION
ERROR
EDIABAS_IFH_0008
Meaning:
Erroneous connection between the interface and the
ECU.
Causes:
Short circuit on the TxD or RxD .
Error correction: Remove short circuit.
Target system:
19
WIN
SCO
QNX
IFH-0009: NO RESPONSE FROM
CONTROLUNIT
EDIABAS_IFH_0009
Meaning:
The ECU is not connected or does not respond.
Causes:
The ECU is not connected (or not properly).
The ECU is not supplied with voltage.
The ECU is addressed with a wrong address.
The ECU parameters are incorrect (concept, times,
etc.).
Error correction: Check the error causes above.
Target system:
20
WIN
SCO
QNX
IFH-0010: DATATRANSMISSION TO
CONTROLUNIT DISTURBED
EDIABAS_IFH_0010
Meaning:
The data transmission between the interface and the
ECU is disturbed.
Causes:
Disturbance on the diagnostic line.
The interface EDIC is not loaded with the diagnostics
protocol requested in the ECU description file (SGBD).
Error correction: Repeat the last job.
Download the required EDIC firmware.
Target system:
WIN
SCO
QNX
13
EDIABAS - ERROR REFERENCE
21
IFH-0011: UNKNOWN INTERFACE
Meaning:
EDIABAS_IFH_0011
This error is inapplicable for EDIABAS V3.0.0 or later.
The error code and associated constants do not exist
due to compatibility reasons.
Causes:
-
Error correction: Target system:
22
WIN
SCO
QNX
IFH-0012: BUFFER OVERFLOW
EDIABAS_IFH_0012
Meaning:
Overflow in one of the internal data buffers of the
Interface Handler.
Causes:
IFH-internal buffer overflow.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
23
WIN
SCO
QNX
EDIABAS_IFH_0013
IFH-0013: COMMAND NOT
IMPLEMENTED
Meaning:
The BEST command called is not supported by the
Interface Handler.
Causes:
An interface is connected in which the functionality
appears behind the BEST command is not integrated
(e.g. IDBSS instead of EDIC).
Error correction: Replace the interface (e.g. EDIC instead of IDBSS).
Target system:
WIN
SCO
QNX
14
EDIABAS - ERROR REFERENCE
24
EDIABAS_IFH_0014
IFH-0014: CONCEPT NOT
IMPLEMENTED
Meaning:
This error is inapplicable for EDIABAS V3.0.0 or later.
The error code and associated constants do not exist
due to compatibility reasons.
You can set this error using the BEST2 function
make_error
Causes:
-
Error correction: Target system:
25
WIN
SCO
QNX
IFH-0015: UBATT ON/OFF ERROR
EDIABAS_IFH_0015
Meaning:
This error message occurs whenever the supply voltage
on the D bus was temporarily interrupted before the
Interface Handler accesses the interface. If the
interruption continues to exist during the current access
to the interface, the error message "IFH-0007: WRONG
UBATT" occurs instead. After the error message is
issued, the status flag in the interface which displayed
this error is automatically deleted by the Interface
Handler.
Causes:
The voltage supplied on the D bus was temporarily
interrupted.
Error correction: Repeat the job.
If the error is to be generally suppressed for all
application programs, set the EDIABAS configuration
element UbattHandling to 0.
Target system:
WIN
SCO
QNX
15
EDIABAS - ERROR REFERENCE
26
IFH-0016: IGNITION ON/OFF ERROR
EDIABAS_IFH_0016
Meaning:
This error message occurs whenever the ignition was
disabled after the last access of the Interface Handler to
the interface, even when it had been re-enabled again
in the meantime. The reason for this error message
cannot be determined from the current status of the
ignition. The current status of the ignition must be
interrogated with the corresponding BEST command
(BEST1: xignit; BEST2: get_ignition_voltage). After the
error message is issued, the status flag in the interface
which caused the error message is automatically
deleted by the Interface Handler
Causes:
Ignition disabled.
Error correction: Enable the ignition and repeat the last job.
If the error is to be generally suppressed for all
application programs, the
EDIABAS configuration
element IgnitionHandling must be set to 0.
Target system:
27
WIN
SCO
QNX
IFH-0017: INTERFACE DEADLOCK
ERROR
EDIABAS_IFH_0017
Meaning:
EDIC BUSY condition is too long (greater than
„deadlock“ timeout).
Causes:
The ECU response time is greater than “deadlock” time.
Several blocks are expected after sending a message
to which the ECU which does not respond (can be set
via BEST command "xawlen").
Error correction: The ECU response time is greater than “deadlock” time.
Set the response length to (BEST1: xawlen {0.i,0.i};
BEST2: set_answer_length).
Target system:
WIN
SCO
QNX
16
EDIABAS - ERROR REFERENCE
28
IFH-0018: INITIALIZATION ERROR
Meaning:
EDIABAS_IFH_0018
Error at initiation of the interface handler
Causes:
The Interface Handler XEDIC.DLL or XEDIC32.DLL is
used, and no EDIC unit is configured in the EDIC API
configuration files.
The Interface Handler was not initialized (shouldn't
occur, since the initialization automatically occurs with
apiInit).
Error correction:
Re-initialize EDIC (with EDIC API).
If the error
continues to occur, please inform SOFTING.
Target system:
29
WIN
SCO
QNX
IFH-0019: DEVICE ACCESS ERROR
EDIABAS_IFH_0019
Meaning:
Execution of the BEST command which accesses the
Interface Hander is denied.
Causes:
This error message always occurs whenever access is
made to the Interface Handler via a BEST command
and the device driver of the interface still has not been
opened.
Error correction: The connection to the driver must first be produced in
the ECU description file. (BEST1: xconnect, BEST2:
open_communication). This is why this command must
be placed before the first command which accesses the
Interface Handler; i.e. this command should principally
appear in the jobs "INITIALIZATION" and “ENDE”.
Target system:
WIN
SCO
QNX
17
EDIABAS - ERROR REFERENCE
30
EDIABAS_IFH_0020
IFH-0020: DRIVER ERROR
Meaning:
Error when accessing the device driver of the interface.
Causes:
The driver is not (or not properly) installed (parameter,
version !?).
Error correction: The driver installation is to be checked according to the
installation instructions enclosed with the interface
used.
Use EDIC as interface; then check your EDIC API
installation in Windows.
Target system:
31
WIN
SCO
QNX
EDIABAS_IFH_0021
IFH-0021: ILLEGAL PORT
Meaning:
Specification of an illegal port number in the ECU
description file (SGBD).
Causes:
Illegal port numbers are used In the BEST commands
(BEST1: xgetport and xsetport, BEST2: ifgetport and
ifsetport).
Error correction: Correction of the port number in the ECU description
file.
Target system:
32
WIN
SCO
QNX
IFH-0022: DRIVER STATUS ERROR
EDIABAS_IFH_0022
Meaning:
The Interface Handler cannot interpret the status
message of the device driver included in the interface.
Causes:
The driver responds with an undefined status message.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
WIN
SCO
QNX
18
EDIABAS - ERROR REFERENCE
33
IFH-0023: INTERFACE STATUS ERROR
EDIABAS_IFH_0023
Meaning:
The Interface Handler cannot interpret the status
message.
Causes:
The interface responds with an undefined status
message.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
34
WIN
SCO
QNX
IFH-0024: CANCEL FAILED
EDIABAS_IFH_0024
Meaning:
Error when resetting the DPRAMs. This error only
occurs
in
connection
with
EDIC
versions
communicating via DPRAM with the PC.
Causes:
The DPRAM and/or the device driver of the interface
are in an undefined state.
Communication problem between the device driver of
the interface and the EDIC firmware.
Error correction: Repeat the job.
Re-load the EDIC firmware.
Target system:
35
WIN
SCO
QNX
IFH-0025: INTERFACE APPLICATION
ERROR
EDIABAS_IFH_0025
Meaning:
Error when opening the device driver of the interface
(BEST1: xconnect, BEST2: open_communication). This
error only occurs together with EDIC versions
communicating via DPRAM with the PC.
Causes:
The firmware was not loaded in EDIC.
Error correction: Download the corresponding EDIC firmware.
Target system:
WIN
SCO
QNX
19
EDIABAS - ERROR REFERENCE
36
IFH-0026: SIMULATION ERROR
EDIABAS_IFH_0026
Meaning:
Error in connection with the ECU Simulator.
Causes:
Syntax error in one of the simulation files.
One of the simulation files is missing or placed in the
wrong directory (see description of the ECU Simulator).
Simulation files created with MS-DOS/WINDOWS were
not converted to the Unix format before being used with
Unix.
Error correction: Correction of the erroneous simulation file(s) (see
description of the ECU Simulator).
Target system:
WIN
SCO
QNX
20
EDIABAS - ERROR REFERENCE
37
EDIABAS_IFH_0027
IFH-0027: IFH NOT FOUND
Meaning:
The Interface Handler is not installed.
Causes:
EDIABAS attempts to access the Interface Handler
although this is not (or incorrectly) installed.
Error correction: Check your application as to whether the EDIC API or
ADS set, respectively, has been installed.
Terminate the application program
Check whether the correct interface is entered in the
EDIABAS configuration.
After the configuration has been corrected, terminate
the Interface Handler and EDIABAS, and re-start:
WIN32: EDIABAS is automatically closed with
the application (automatic restart)
WIN16: Close EDIABASW.EXE via the system
menu (automatic re-start)
SCO:
Call shell script apiclose
Call shell script apiboot
QNX:
Call shell script apiclose
Call shell script apiboot
Re-start the application program.
Target system:
WIN
SCO
QNX
21
EDIABAS - ERROR REFERENCE
38
IFH-0028: ILLEGAL IFH VERSION
EDIABAS_IFH_0028
Meaning:
A wrong Interface Handler version is installed.
Causes:
Your EDIABAS requires a different Interface Handler
version than that which is installed.
Error correction: Re-install the required EDIABAS version and possibly
the Extension Disk.
Re-install the required EDIC API or ADS version,
respectively.
Target system:
39
WIN
SCO
QNX
IFH-0029: ACCESS DENIED
EDIABAS_IFH_0029
Meaning:
Access to the Interface Handler is presently not
possible.
Causes:
Only one program can access the Interface Handler at
the same time. When a program accesses the Interface
Handler, this was already connected to another
program.
Error correction: Terminate all programs which currently access the
Interface Handler.
Target system:
WIN
SCO
QNX
22
EDIABAS - ERROR REFERENCE
40
IFH-0030: TASK COMMUNICATION
ERROR
EDIABAS_IFH_0030
Meaning:
Communication between EDIABAS and the Interface
Handler is disturbed.
Causes:
Communication data from the Interface Handler are
erroneous or the communication medium is damaged. If
the Interface Handler does not respond within a
specified time, this error is also issued..
Error correction: If this error repeatedly occurs, re-start the application
program. If the error is still not corrected, re-start your
system.
Target system:
41
WIN
SCO
QNX
IFH-0031: DATA OVERFLOW
EDIABAS_IFH_0031
Meaning:
The input buffer is full.
Causes:
Excessive data is transferred from EDIABAS to the
Interface Handler.
Error correction: Not possible by the user. If this error still occurs, please
contact SOFTING.
Target system:
42
WIN
SCO
QNX
EDIABAS_IFH_0032
IFH-0032: IGNITION IS OFF
Meaning:
This error messages occurs whenever the ignition is
disabled while the Interface Handler accesses the ECU.
Causes:
The ignition is disabled.
Error correction: Enable the ignition, and repeat the last job.
Target system:
WIN
SCO
QNX
23
EDIABAS - ERROR REFERENCE
44
IFH-0034: CONFIGURATION FILE NOT
FOUND
EDIABAS_IFH_0034
Meaning:
This error message occurs whenever the configuration
files for the EDIC API couldn't be found.
Causes:
The EDIC API configuration files do not exist (or do not
reside in the correct directory).
Error correction: Re-install EDIC. If the error should continue to occur,
please inform SOFTING.
Target system:
45
WIN
SCO
QNX
IFH-0035: CONFIGURATION ERROR
EDIABAS_IFH_0035
Meaning:
At least one configuration element in one of the EDIC
API configuration files is incorrectly configured.
Causes:
Erroneous configuration of an EDIC API configuration
element.
Error correction: In case of an erroneous configuration, the files
EDICHW.LOG or EDICFW.LOG, respectively, are
stored in the configuration file directory. In this file, the
erroneous configurations are listed.
Re-install EDIC. If this error should continue to occur,
inform SOFTING.
Target system:
WIN
SCO
QNX
24
EDIABAS - ERROR REFERENCE
46
EDIABAS_IFH_0036
IFH-0036: LOAD ERROR
Meaning:
This error message occurs when an error occurs while
loading the EDIC firmware.
Causes:
Erroneous configuration.
EDIC is not connected.
Error correction: Check the cables and the EDIC API configuration (was
a *.LOG file created?).
If necessary, re-install the EDIC (firmware). If this error
should continue to occur, inform SOFTING.
Target system:
47
WIN
SCO
QNX
EDIABAS_IFH_0037
IFH-0037: LOW UBATT
Meaning:
This error occurs whenever a voltage is currently
supplied to the D bus and when a connected ECU does
not respond. The error message is issued only after
BEST command which access the D bus. These are:
Send and receive a message.
Request the ECU keybytes and identification
files.
This error message is suppressed for all other BEST
commands of the Interface Handler (e.g. read the ports
or set ECU parameters). As soon as the correct voltage
is supplied to the D bus, no error message is issued
anymore after executing the BEST commands above.
Causes:
The supply voltage is too low on the D bus, and the
ECU does not respond.
Error correction: Increase voltage supply on the D bus.
Target system:
WIN
SCO
QNX
25
EDIABAS - ERROR REFERENCE
48
IFH-0038: INTERFACE COMMAND NOT
IMPLEMENTED
EDIABAS_IFH_0038
Meaning:
The command used by the Interface Handler to the
interface is not supported by the interface.
Causes:
The current interface version does not support the
command used.
Error correction: Install an interface which supports the commands used.
Target system:
49
WIN
SCO
QNX
IFH-0039: EDIC USER INTERFACE NOT
FOUND
EDIABAS_IFH_0039
Meaning:
Component EDICX.EXE or EDICX32.EXE couldn't be
found
Causes:
Component .EDICX.EXE or EDICX32.EXE is missing in
the installation
Error correction: Re-install the EDIC. If this error should continue to
occur, inform SOFTING.
Target system:
WIN
SCO
QNX
26
EDIABAS - ERROR REFERENCE
50
IFH-0040: ILLEGAL EDIC USER
INTERFACE VERSION
EDIABAS_IFH_0040
Meaning:
The version of the EDIC user interface does not match
the version of the EDIC API:
Causes:
EDIC API was installed incorrectly or parts of the EDIC
API
(EDIC.DLL,
EDIC32.DLL,
EDICX.EXE,
EDICX32.EXE) reside in the Windows directory.
Error correction: Delete all components of the EDIC API (EDIC.DLL,
EDIC32.DLL, EDICX.EXE, EDICX32.EXE) which reside
in the Windows directory.
Re-install the EDIC. If this error should continue to
occur, inform SOFTING.
Target system:
51
WIN
SCO
QNX
IFH-0041: ILLEGAL PARAMETERS
EDIABAS_IFH_0041
Meaning:
Faulty function parameter transfer to the EDIC API.
Causes:
A function of EDIC API received parameters not within
the range of values.
Error correction: Cannot be performed by the user. If this error should
occur, please inform SOFTING.
Target system:
52
WIN
SCO
QNX
IFH-0042: CARD INSTALLATION
ERROR
EDIABAS_IFH_0042
Meaning:
Error during installation of the EDICcard.
Causes:
The EDICcard could not be installed correctly.
Error correction: Re-install EDIC. If this error should continue to occur,
please inform SOFTING.
Target system:
WIN
SCO
QNX
27
EDIABAS - ERROR REFERENCE
53
IFH-0043: COMMUNICATION TRACE
ERROR
EDIABAS_IFH_0043
Meaning:
Error in the EDIC communication trace.
Causes:
No access to DPRAM possible.
Error correction: Re-install EDIC. If this error should continue to occur,
please inform SOFTING.
Target system:
54
WIN
SCO
QNX
EDIABAS_IFH_0044
IFH-0044: FLASH ERROR
Meaning:
An error was found during the flash process of the EDIC
firmware.
Causes:
Faulty EDIC API configuration, the
corrupted, or the EDIC is not connected.
firmware
is
Error correction: Check the EDIC connectors on the computer and the
EDIC
API
configuration
(EDICHW.INI
and
EDICFW.INI).
Target system:
55
WIN
SCO
QNX
IFH-0045: RUNBOARD ERROR
EDIABAS_IFH_0045
Meaning:
An error has occurred during initialization of the EDICPC3.
Causes:
Faulty EDIC API configuration.
Error correction: Check your EDIC API configuration (EDICHW.INI and
EDIC-PC3 configuration).
Target system:
WIN
SCO
QNX
28
EDIABAS - ERROR REFERENCE
56
IFH-0046: EDIC API ACCESS ERROR
EDIABAS_IFH_0046
Meaning:
An error has occurred during starting of the application
program.
Causes:
An application program in another directory already
uses the EDIC API.
Error correction: Terminate the other application program and restart
your application program.
Target system:
57
WIN
SCO
QNX
EDIABAS_IFH_0047
IFH-0047: PLUGIN ERROR
Meaning:
A plug-in DLL could not be loaded, or access to this
DLL was not possible.
Causes:
Faulty EDIC API configuration, plug-in DLL not found,
or the plug-in DLL needs another DLL which was not
found.
Error correction: Cannot be performed by the user. If this error should
re-occur, please inform the company which has
implemented your plug-in DLL.
Target system:
58
WIN
SCO
QNX
IFH-0048: PLUGIN FUNCTION ERROR
EDIABAS_IFH_0048
Meaning:
One function in a plug-in DLL could not be accessed.
Causes:
The function in the plug-in DLL is missing or
implemented incorrectly.
Error correction: Cannot be performed by the user. If this error should
re-occur, please inform the company which has
implemented your plug-in DLL.
Target system:
WIN
SCO
QNX
29
EDIABAS - ERROR REFERENCE
59
IFH-0049: CSS DEVICE DETECTION
ERROR
EDIABAS_IFH_0049
Meaning:
A C&SS EDIC was not found.
Causes:
Faulty configuration, or the necessary system resources
(IRQ, memory) are not available.
Error correction: Please check the EDIC API configuration (EDICHW.INI,
the driver, IRQ and memory configuration).
Target system:
200
WIN
SCO
QNX
IFH-0050: ENTRY IN DYNAMIC
CONFIGURATION NOT
FOUND
EDIABAS_IFH_0050
Meaning:
During the dynamic reloading of protocols, an internal
error has occurred.
Causes:
An entry in the EDIC API configuration file for the
dynamic reloading of protocols is faulty or missing.
Error correction: Re-install the firmware. If the same error should occur
again, please inform the company which has
implemented your application program.
Target system:
201
WIN
SCO
QNX
IFH-0051: INTERNAL DYNAMIC
PROTOCOL ERROR
EDIABAS_IFH_0051
Meaning:
During the dynamic reloading of protocols, an internal
error has occurred.
Causes:
An illegal program status of the EDIC API has occurred.
Error correction: Cannot be performed by the user. If this error should
re-occur, inform SOFTING.
Target system:
WIN
SCO
QNX
30
EDIABAS - ERROR REFERENCE
202
IFH-0052: CONCEPT NOT AVALIABLE
EDIABAS_IFH_0052
Meaning:
The selected concept is not available.
Causes:
For the selected concept, no firmware is available or
has been configured in the EDIC API configuration.
Error correction: Re-install the firmware. If this error should continue to
occur, please inform the company which has
implemented your application program.
Target system:
203
WIN
SCO
QNX
IFH-0053: ILLEGAL CONCEPT ID
EDIABAS_IFH_0053
Meaning:
Illegal concept number.
Causes:
The selected concept number has an illegal value.
Error correction: Cannot be performed by the user. If this error should
occur, please inform the company which has
implemented your application program.
Taget system:
204
WIN
SCO
QNX
IFH-0054: ILLEGAL FUNCTION
PARAMETER
EDIABAS_IFH_0054
Meaning:
An EDIC API function was called with an illegal
parameter.
Causes:
An illegal program status of the EDIC API has occurred.
Error correction: Cannot be performed by the user. If this error should
occur, please inform SOFTING.
Target system:
WIN
SCO
QNX
31
EDIABAS - ERROR REFERENCE
205
IFH-0055: CANNOT LOAD PROTOCOL
TABLES
EDIABAS_IFH_0055
Meaning:
The dynamic reloading of protocol tables has failed.
Causes:
Faulty firmware
configuration.
configuration
in
the
EDIC
API
Error correction: Re-install the firmware. If this error should continue to
occur, please inform the company which has
implemented your application program.
Target system:
206
WIN
SCO
QNX
IFH-0056: ILLEGAL CHANNEL
EDIABAS_IFH_0056
Meaning:
Transfer of an illegal channel number to EDIC API.
Causes:
An illegal channel number was passed to EDIC API.
Error correction: Cannot be performed by the user. If this error should
occur, please inform the company which has
implemented your application program.
Target system:
207
WIN
SCO
QNX
IFH-0057: ERROR READ DIGITAL
INPUTS
EDIABAS_IFH_0057
Meaning:
Error during reading of a digital EDIC input.
Causes:
An error has occurred during reading of a digital EDIC
input.
Error correction: Cannot be performed by the user. If this error should
occur, please inform SOFTING.
Target system:
WIN
SCO
QNX
32
EDIABAS - ERROR REFERENCE
208
IFH-0058: ERROR SET DIGITAL
OUTPUTS
EDIABAS_IFH_0058
Meaning:
Error during setting a digital EDIC output.
Causes:
An error has occurred during the setting of a digital
EDIC output.
Error correction: Cannot be performed by the user. If this error should
occur, please inform SOFTING.
Target system:
209
WIN
SCO
QNX
IFH-0059: ERROR READ ANALOG
INPUTS
EDIABAS_IFH_0059
Meaning:
Error during reading an analog EDIC input.
Causes:
An error has occurred during the reading of an analog
EDIC input.
Error correction: Cannot be performed by the user. If this error should
occur, please inform SOFTING.
Target system:
WIN
SCO
QNX
33
EDIABAS - ERROR REFERENCE
4.2. Runtime system
4.2.1. BIP, BEST Interpreter
60
BIP-0000: INTERNAL ERROR
EDIABAS_BIP_0000
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
Program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
61
WIN
SCO
QNX
EDIABAS_BIP_0001
BIP-0001: OUT OF RANGE
Meaning:
Job parameter too long or illegal index when accessing
string registers.
Causes:
This error usually always occurs whenever access is
made to an array variable with a calculated index and
this is too large.
Example:
i=100;
array[100*i]=50;
Error correction: Check all array accesses in your job if they contain an
index which is possibly invalid. The indexes must not
exceed 1024/element size.
Target system:
WIN
SCO
QNX
34
EDIABAS - ERROR REFERENCE
62
BIP-0002: IFH FUNCTION ERROR
EDIABAS_BIP_0002
Meaning:
The Interface Handler function cannot be executed.
Causes:
Error when calling an Interface Handler function.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
63
WIN
SCO
QNX
BIP-0003: OBJECT FILE ERROR
EDIABAS_BIP_0003
Meaning:
Error when reading the ECU description file.
Causes:
The ECU description file is possibly damaged or a
transmission error occurred when accessing via a
network.
Error correction: If the error repeatedly occurs, re-compile the description
file.
Target system:
64
WIN
SCO
QNX
BIP-0004: ILLEGAL OPCODE
EDIABAS_BIP_0004
Meaning:
Erroneous ECU description file.
Causes:
The ECU description file is possibly damaged or a
transmission error occurred when accessing via a
network.
Error correction: If an error repeatedly occurs, re-compile the description
file
Target system:
WIN
SCO
QNX
35
EDIABAS - ERROR REFERENCE
65
BIP-0005: STACK OVERFLOW
EDIABAS_BIP_0005
Meaning:
Overflow of the BEST stack.
Causes:
The 2 KB stack area in the BEST interpreter is too small
to execute the job. Either the job has a nesting depth
which is too large or one of the functions form the
runtime library is erroneous and does not clear the
affected stack area.
Error correction: Simplify the erroneous job or determine the function
which issued this error.
Target system:
66
WIN
SCO
QNX
BIP-0006: BEST FILE ERROR
EDIABAS_BIP_0006
Meaning:
Error when processing a BEST data file.
Causes:
An error occurred in one of the BEST data commands.
If this occurs when opening the file (fopen), either the
file does not exist or it cannot be read. If the error
occurred when positioning the file pointer (BEST2
functions fseek, fseekln), attempt was made to position
the pointer outside of the file. In the case of a read
command, the error refers to a real read problem.
Error correction: Check whether the file to be searched exists. If yes, test
the accesses to the file within the job.
Target system:
WIN
SCO
QNX
36
EDIABAS - ERROR REFERENCE
67
BIP-0007: DIVISION BY ZERO
EDIABAS_BIP_0007
Meaning:
Division by 0.
Causes:
Division by 0 occurred while a job was being executed.
Error correction: Check whether a division by 0 can occur in the code of
a job. Trap this case before the division! Example:
if(a==0)
b=1000;
else
b=1000/a;
Target system:
68
WIN
SCO
QNX
EDIABAS_BIP_0008
BIP-0008: BEST BREAK
Meaning:
Interruption by the description file.
Causes:
The command "break" (BEST/1) was called in the
description file. This command can be installed, for
example, for testing purposes in the ECU description
file (SGBD).
Error correction: Remove this command form the description file.
Target system:
69
WIN
SCO
QNX
BIP-0009: BEST VERSION ERROR
EDIABAS_BIP_0009
Meaning:
Erroneous BEST version of the ECU description file.
Causes:
The ECU description file addressed was compiled by a
compiler which is not compatible with this EDIABAS
version.
Error correction: Compile the ECU description file using the compiler
included in this EDIABAS version.
Target system:
WIN
SCO
QNX
37
EDIABAS - ERROR REFERENCE
70
BIP-0010: CONSTANT DATA ACCESS
ERROR
EDIABAS_BIP_0010
Meaning:
Error when accessing constants (tables).
Causes:
This error occurs with the table commands. If the
specified table or table column does not exist, this error
message is issued.
Error correction: Check whether the names of the tables and columns
specified in the ECU description file agree with the
actually existing tables.
Target system:
WIN
SCO
QNX
38
EDIABAS - ERROR REFERENCE
71
EDIABAS_BIP_0011
BIP-0011: REAL ERROR
Meaning:
Over or underflow of a mathematical function
Causes:
This error occurs in connection with the real processing
functions. The representable numeric range was
exceeded or fallen short of for an arithmetical operation.
Error correction: Check the function parameters specified in the ECU
description file which were transferred to the real
functions for computing real values.
Target system:
72
WIN
SCO
QNX
BIP-0012: PLUG IN NOT FOUND
EDIABAS_BIP_0012
Meaning:
The plug-in component was not found.
Causes:
Before an ECU description file can access a plug-in
component, this component must be installed in your
system.
The error occurs because the plug-in component does
not exist.
Error correction: For eliminating the error, contact the developer of the
ECU description file.
Target system:
73
WIN
SCO
QNX
EDIABAS_BIP_0013
BIP-0013: PLUG IN ERROR
Meaning:
Faulty call of the plug-in component.
Causes:
In the plug-in component, an error has occurred.
Error correction: For eliminating the error, contact the developer of the
ECU description file.
Target system:
WIN
SCO
QNX
39
EDIABAS - ERROR REFERENCE
74
BIP-0014: PLUG IN VERSION ERROR
EDIABAS_BIP_0014
Meaning:
Wrong version of Plug-In component
Causes:
No correct Plug-In component for ECU description file.
Error correction: No correct installation of EDIABAS system.
Target system:
75
WIN
SCO
QNX
BIP-0015: PLUG IN STACK ERROR
Meaning:
Error in Plug-In component.
Causes:
Error in Plug-In component
EDIABAS_BIP_0015
Error correction: Contact the deloper of the Plug-In component.
Target system:
76
WIN
SCO
QNX
BIP-0016: PLUG IN FUNCTION NOT
FOUND
Meaning:
Error in Plug-In component.
Causes:
Error in Plug-In component
EDIABAS_BIP_0016
Error correction: Contact the deloper of the Plug-In component.
Target system:
WIN
SCO
QNX
40
EDIABAS - ERROR REFERENCE
4.2.2. SYS, sequence control
90
SYS-0000: INTERNAL ERROR
EDIABAS_SYS_0000
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
91
WIN
SCO
QNX
SYS-0001: ILLEGAL FUNCTION
EDIABAS_SYS_0001
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
The application program transferred
communication to EDIABAS.
an
illegal
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
WIN
SCO
QNX
41
EDIABAS - ERROR REFERENCE
92
SYS-0002: ECU OBJECT FILE NOT
FOUND
EDIABAS_SYS_0002
Meaning:
The ECU variant description file couldn't be found.
Causes:
Either the description file does not exist in the EDIABS
search path or the search path is wrong.
EDIABAS search path:
The EDIABAS configuration element EcuPath describes
the EDIABAS search path. When the configuration
setting does not exist, the current directory is used by
EDIABAS as the search path.
Error correction: Description file does not exist:
Copy the requested description file in the EDIABAS
search path.
Search path is wrong:
Terminate the application program, and assign the
correct path to configuration element EcuPath.
In case the configuration changes, terminate EDIABAS,
and re-start.:
WIN32:
EDIABAS is automatically closed
with the application (automatic
restart)
WIN16:
Close EDIABASW.EXE via system
menu
(automatic re-start)
SCO:
Call shell script apiclose
Call shell script apiboot
QNX:
Call shell script apiclose
Call shell script apiboot
Re-start the application program.
Target system:
WIN
SCO
QNX
42
EDIABAS - ERROR REFERENCE
93
SYS-0003: ECU OBJECT FILE ERROR
EDIABAS_SYS_0003
Meaning:
Error when reading the ECU variant description file.
Causes:
Description file may be damaged or transmission errors
occurred while accessing via a network.
Error correction: If an error repeatedly occurs, re-compile the description
file.
Target system:
94
WIN
SCO
QNX
SYS-0004: ILLEGAL FORMAT OF ECU
OBJECT FILE
EDIABAS_SYS_0004
Meaning:
Illegal format of the ECU variant description file.
Causes:
The description file is damaged.
Error correction: Re-compile the description file.
Target system:
WIN
SCO
QNX
43
EDIABAS - ERROR REFERENCE
95
SYS-0005: OBJECT FILE NOT FOUND
EDIABAS_SYS_0005
Meaning:
The ECU description file couldn't be found.
Causes:
Either the description file does not exist in the EDIABAS
search path or the search path is wrong.
EDIABAS search path:
The EDIABAS configuration element EcuPath describes
the EDIABAS search path. If a configuration setting
does not exist, the current directory is used by
EDIABAS as the search path.
Error correction: Description file does not exist:
Copy the required description file in the EDIABAS
search path.
Such path is wrong:
Terminate the application program, and assign the
correct path to configuration element EcuPath.
In case the configuration changed, terminate EDIABAS,
and re-start.:
WIN32:
EDIABAS is automatically closed
with the application (automatic
restart)
WIN16:
Close EDIABASW.EXE via system
menu
(automatic re-start)
SCO: Call shell script apiclose
Call shell script apiboot
QNX: Call shell script apiclose
Call shell script apiboot
Re-start the application program.
Target system:
WIN
SCO
QNX
44
EDIABAS - ERROR REFERENCE
96
SYS-0006: GROUP OBJECT FILE
ERROR
EDIABAS_SYS_0006
Meaning:
Error when reading the ECU group description file.
Causes:
The description file may be damaged or transmission
errors occurred when accessing via a network.
Error correction: If the error repeatedly occurs, re-compile the description
file.
Target system:
97
WIN
SCO
QNX
SYS-0007: ILLEGAL FORMAT OF GROUP
OBJECT FILE
EDIABAS_SYS_0007
Meaning:
Illegal format of the ECU group description file.
Causes:
The description file is damaged.
Error correction: Re-compile the description file.
Target system:
98
WIN
SCO
QNX
SYS-0008: JOB NOT FOUND
EDIABAS_SYS_0008
Meaning:
The job couldn't be found in the ECU description file.
Causes:
The job is missing in the description file, or the
description file is wrong.
Error correction: Check if the desired job exists in the description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list all job names:
bestinfo <Name of the description file with path and
extension>
Also check exactly if the job is spelled correct.
If the desired job does not exist in the description file,
extend the description file by the job.
Target system:
WIN
SCO
QNX
45
EDIABAS - ERROR REFERENCE
99
SYS-0009: NO INITIALIZATION JOB
EDIABAS_SYS_0009
Meaning:
The job INITIALISIERUNG couldn't be found in the ECU
description file.
Causes:
The job INITIALISIERUNG is automatically executed by
EDIABAS; however, the job is missing in the description
file.
Error correction: The description file is to be extended by the job
INITIALISIERUNG.
Target system:
100
WIN
SCO
QNX
SYS-0010: INITIALIZATION ERROR
EDIABAS_SYS_0010
Meaning:
The job INITIALISIERUNG indicates an erroneous
initialization.
Causes:
The job INITIALISIERUNG is automatically executed by
EDIABAS. Whether the initialization was successful or
not is reported with the result DONE:
DONE = 0
DONE <> 0
Error during initialization
Successful initialization
An error occurred during the job INITIALISIERUNG.
The result DONE was therefore 0.
Error correction: If an error repeatedly occurs, please contact the
developer of the description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the names of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
WIN
SCO
QNX
46
EDIABAS - ERROR REFERENCE
101
SYS-0011: NO IDENTIFICATION JOB
EDIABAS_SYS_0011
Meaning:
The job IDENTIFIKATION couldn't be found in the ECU
group description file.
Causes:
The job IDENTIFIKATION is automatically executed by
EDIABAS; however, the job is missing in the description
file.
Error correction: The description file is to be extended by the job
IDENTIFIKATION.
Target system:
102
WIN
SCO
QNX
SYS-0012: IDENTIFICATION ERROR
EDIABAS_SYS_0012
Meaning:
The job IDENTIFIKATION in the ECU group description
file couldn't identify the ECU variant.
Causes:
The job IDENTIFIKATION is automatically executed by
EDIABAS. Whether the identification was a success or
not is displayed with the result VARIANTE:
Variant couldn't be identified:
VARIANTE = <empty>
Variant successfully identified:
VARIANTE = <Name of the ECU variant
description file without extension>
An error occurred during job IDENTIFIKATION. The
result VARIANTE was therefore empty.
Error correction: If an error repeatedly occurs, please contact the
developer of the description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the name of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
WIN
SCO
QNX
47
EDIABAS - ERROR REFERENCE
103
SYS-0013: UNEXPECTED RESULT
EDIABAS_SYS_0013
Meaning:
An illegal result was returned either in the job
IDENTIFIKATION of the ECU group description file or in
the job INITIALISIERUNG of the group or variant
description file.
Causes:
The job IDENTIFIKATION may only return the result
VARIANTE, and the job INITIALISIERUNG may only
return the result DONE.
Another result, however, was returned in one of the jobs
mentioned.
Error correction: If an error occurs, please contact the developer of the
description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the name of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
104
WIN
SCO
QNX
SYS-0014: ILLEGAL FORMAT
EDIABAS_SYS_0014
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A result format cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
WIN
SCO
QNX
48
EDIABAS - ERROR REFERENCE
105
SYS-0015: TASK COMMUNICATION
ERROR
EDIABAS_SYS_0015
Meaning:
Communication between EDIABAS and the application
program is disturbed.
Causes:
Communication data from the application program is
incorrect.
Error correction: If this error repeatedly occurs, re-start the application
program. If the error is still not corrected, re-start your
system.
Target system:
WIN
SCO
QNX
49
EDIABAS - ERROR REFERENCE
106
SYS-0016: ILLEGAL CONFIGURATION
EDIABAS_SYS_0016
Meaning:
EDIABAS configuration couldn't be executed.
Causes:
An illegal configuration setting resides in the EDIABAS
configuration file EDIABAS.INI.
Error correction: Terminate the application program, and check all
EDIABAS configuration settings.
After correcting the configuration, terminate EDIABAS,
and re-start:
WIN32:
EDIABAS is automatically closed
with the application (automatic
restart)
WIN16:
Close EDIABASW.EXE via system
menu
(automatic restart)
SCO: Call shell script apiclose
Call shell script apiboot
QNX: Call shell script apiclose
Call shell script apiboot
Re-start the application program.
Target system:
107
WIN
SCO
QNX
Reserved for future EDIABAS versions
EDIABAS_SYS_0017
50
EDIABAS - ERROR REFERENCE
108
SYS-0018: END JOB ERROR
EDIABAS_SYS_0018
Meaning:
A processing error occurred in the job ENDE.
Causes:
The job ENDE is automatically executed by EDIABAS.
An error occurred while a job was being processed, or a
result was returned.
Error correction: If an error repeatedly occurs, please contact the
developer of the description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the name of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
109
WIN
SCO
QNX
EDIABAS_SYS_0019
SYS-0019: TIMER ERROR
Meaning:
Error when requesting a timer by EDIABAS.
Causes:
All timers under Windows are already used by other
Windows programs.
Error correction: Terminate other Windows programs with timer use; e.g.
Windows clock programs.
Target system:
WIN
SCO
QNX
51
EDIABAS - ERROR REFERENCE
110
SYS-0020: BASE OBJECT FILE NOT
FOUND
EDIABAS_SYS_0020
Meaning:
The ECU base description file couldn't be found.
Causes:
Either the EDIABAS search path does not exist in the
description file, or the search path is wrong.
EDIABAS search path:
The EDIABAS configuration element EcuPath describes
the EDIABAS search path. If a configuration setting
does not exist, the current directory is assumed by
EDIABAS as the search path.
Error correction: Description file does not exist:
Copy the required description file in the EDIABAS
search path.
Such path is wrong:
Terminate the application program, and assign the
correct path to the configuration element EcuPath.
If the configuration changed, terminate EDIABAS, and
re-start:
WIN32:
EDIABAS is automatically closed
with the application (automatic
restart)
WIN16:
Close EDIABASW.EXE via system
menu
(automatic restart)
SCO: Call shell script apiclose
Call shell script apiboot
QNX: Call shell script apiclose
Call shell script apiboot
Re-start the application program.
Target system:
WIN
SCO
QNX
52
EDIABAS - ERROR REFERENCE
111
SYS-0021: BASE OBJECT FILE ERROR
EDIABAS_SYS_0021
Meaning:
Error when reading the ECU base description file.
Causes:
The description file may be damaged, or transmission
errors occurred while accessing via a network.
Error correction: If the error repeatedly occurs, re-compile the description
file.
Target system:
112
WIN
SCO
QNX
SYS-0022: ILLEGAL FORMAT OF BASE
OBJECT FILE
EDIABAS_SYS_0022
Meaning:
Illegal format of the ECU base description file.
Causes:
The description file is damaged.
Error correction: Re-compile the description file.
Target system:
113
WIN
SCO
QNX
SYS-0023: PASSWORD ERROR
EDIABAS_SYS_0023
Meaning:
Error when starting the EDIABAS runtime system.
Causes:
The EDIABAS system was incorrectly installed, or the
installation was subsequently changed by manually
copying files.
Error correction: Re-install EDIABAS.
Target system:
WIN
SCO
QNX
53
EDIABAS - ERROR REFERENCE
114
SYS-0024: ILLEGAL PASSWORD
EDIABAS_SYS_0024
Meaning:
The ECU description file cannot be executed..
Causes:
The ECU description file is protected with passwords
which are not known by the runtime system.
Error correction: If the description file exists as source code (B2G, B2V),
re-compile the description file with a password known
by the system.
If the description file only exists in object format (GRP,
PRG), the error cannot be corrected.
Target system:
WIN
SCO
QNX
54
EDIABAS - ERROR REFERENCE
4.3. API, Application Programming Interface
120
API-0000: INTERNAL ERROR
EDIABAS_API_0000
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
121
WIN
SCO
QNX
EDIABAS_API_0001
API-0001: USER BREAK
Meaning:
The job was aborted.
Causes:
The job was aborted by the application program.
Abortion of EDIABAS by the application program
(apiEnd) can also abort a job in progress.
Error correction: Please contact the developer of the application
program.
Target system:
122
WIN
SCO
QNX
API-0002: MEMORY ALLOCATION
ERROR
EDIABAS_API_0002
Meaning:
Not enough working memory (RAM).
Causes:
The working memory does not suffice for the results
returned from the job.
Error correction: If this error repeatedly occurs, terminate other
application programs in order to increase the working
memory available.
Target system:
WIN
SCO
QNX
55
EDIABAS - ERROR REFERENCE
123
API-0003: RESULT SETS OVERFLOW
EDIABAS_API_0003
Meaning:
The job returns too many result records.
Causes:
The maximum possible number of result records
comprises 65535. Too many result records were
returned from the job.
Error correction: Reduce the number of result records in the job.
If applicable, contact the developer of the description
file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the name of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
124
WIN
SCO
QNX
API-0004: RESULTS OVERFLOW
EDIABAS_API_0004
Meaning:
The job returned too many results.
Causes:
The maximum possible number of results within a result
record is limited to 65535. From the job, too many
results were returned within a record set.
Error correction: Reduce the number of results within the result record.
If applicable, please contact the developer of the
description file.
The program BESTINFO (contained in the RUNTIME
SYSTEM) can be used to list the name of the
description file developer:
bestinfo <Name of the description file with path and
extension>
Target system:
WIN
SCO
QNX
56
EDIABAS - ERROR REFERENCE
125
API-0005: ILLEGAL RESULT FORMAT
EDIABAS_API_0005
Meaning:
Illegal result format.
Causes:
A result cannot be converted into the format desired by
the application program.
This is the case when
arbitrary formats are converted from or into the
APIBINARY format. Also, an error can occur when
converting a value from or into the APITEXT format.
Error correction: Please contact the developer of the application program
for matching the result format to the description file (or
vice versa).
Target system:
126
WIN
SCO
QNX
API-0006: ACCESS DENIED
EDIABAS_API_0006
Meaning:
Access of the application to EDIABAS is currently not
possible.
Causes:
At the time no further application programs can access
EDIABAS.
Error correction: If this error repeatedly occurs, terminate a program with
access to EDIABAS.
Target system:
WIN
SCO
QNX
57
EDIABAS - ERROR REFERENCE
127
API-0007: INCORRECT
CONFIGURATION FILE
EDIABAS_API_0007
Meaning:
Error when reading configuration file ipc.ini, or
application program uses an old version of API library.
Causes:
The path of configuration file ipc.ini must be stored in
the environment variable IPC_CONFIG (only with SCO
UNIX).
The error occurs with wrong or unassigned environment
variable IPC_CONFIG. Also, the error then occurs
when the configuration file ipc.ini does not exist in the
path specified by the environment variable
IPC_CONFIG.The error also occurs when the
application program uses an old version of API library.
Error correction: Check the assignment of the environment variable
IPC_CONFIG. When the environment variable
IPC_CONFIG is properly set, check if configuration file
ipc.ini exists. Your application program must contain
read access to configuration file IPC.INI and a
compatible version of the API library.
Start EDIABAS with apiboot.
Target system:
WIN
SCO
QNX
58
EDIABAS - ERROR REFERENCE
128
API-0008: TASK COMMUNICATION
ERROR
EDIABAS_API_0008
Meaning:
Communication between the application program and
EDIABAS is disturbed.
Causes:
Communication data from EDIABAS are erroneous, or
the communication medium is damaged. If EDIABAS
does not respond within a specified time, this error is
also issued.
Error correction: If this error repeatedly occurs, re-start the application
program. If the error is still not corrected, re-start your
system.
Target system:
WIN
SCO
QNX
59
EDIABAS - ERROR REFERENCE
129
API-0009: EDIABAS NOT FOUND
EDIABAS_API_0009
Meaning:
EDIABAS is not installed or cannot be found.
Causes:
Before an application program accesses EDIABAS, this
must be installed on your system. EDIABAS must be
started prior to starting an application program.
The error occurred due to a fail start of EDIABAS.
Error correction: Terminate the application program, and check whether
EDIABAS is correctly installed on your system
Start EDIABAS if this has not already been done:
WIN: Occurs automatically
SCO: Call shell script apiboot
QNX: Call shell script apiboot
Re-start your application program.
Target system:
130
WIN
SCO
QNX
API-0010: ILLEGAL EDIABAS VERSION
EDIABAS_API_0010
Meaning:
Wrong EDIABAS version installed.
Causes:
The application requires a different EDIABAS version
than that which is installed.
Error correction: Install the required EDIABAS version.
If applicable, contact the developer of the application
program.
Target system:
WIN
SCO
QNX
60
EDIABAS - ERROR REFERENCE
131
API-0011: ILLEGAL ECU PATH
EDIABAS_API_0011
Meaning:
Illegal ECU path.
Causes:
The configuration element EcuPath is assigned with an
invalid path
Error correction: Terminate the application program, and correct the
environment variable ECU.
Target system:
132
WIN
SCO
QNX
API-0012: SIGNAL SERVER NOT
FOUND
EDIABAS_API_0012
Meaning:
The signal server is still not installed.
Causes:
Before an application accesses EDIABAS, this must
first be installed on your system. Before the application
program is started, the signal server (only under QNX)
must be started in addition to EDIABAS.
Error correction: Terminate the application program, and check whether
EDIABAS is properly installed on your system
Start EDIABAS and the signal server (only necessary
under QNX) if this has not already been done:
Call shell script apiboot
Re-start your application program.
Target system:
133
WIN
SCO
QNX
API-0013: INITIALIZATION ERROR
EDIABAS_API_0013
Meaning:
Error in initializing EDIABAS.
Causes:
The application program did not initialize EDIABAS
(apilnit/apiInitExt) prior to accessing EDIABAS.
Error correction: Please contact the developer of the application
program.
Target system:
WIN
SCO
QNX
61
EDIABAS - ERROR REFERENCE
134
API-0014: RESULT NOT FOUND
EDIABAS_API_0014
Meaning:
Error interrogating a result.
Causes:
The result requested from the application program was
not returned in the required result record by the job.
Error correction: Add result in the result record.
If applicable, contact the developer of the application
program.
Target system:
WIN
SCO
QNX
62
EDIABAS - ERROR REFERENCE
135
API-0015: HOST COMMUNICATION
ERROR
EDIABAS_API_0015
Meaning:
Communication between API.DLL and EDIABAS is
disturbed.
Causes:
Communication data from EDIABAS are erroneous, or
the communication medium is damaged. If EDIABAS
does not respond within a specified time, this error is
also issued.
Error correction: If this error repeatedly occurs, re-start the application
program. If the error has still not been corrected, restart your system.
Target system:
WIN
SCO
QNX
63
EDIABAS - ERROR REFERENCE
4.4. Network
150
NET-0000: INTERNAL ERROR
EDIABAS_NET_0000
Meaning:
The error indicates an illegal program EDIABAS state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
151
WIN
SCO
QNX
NET-0001: UNKNOWN ERROR
EDIABAS_NET_0001
Meaning:
Unknown error.
Causes:
Network communication is disturbed.
Error correction: If this error repeatedly occurs, re-start the application
program. If this error is still not corrected, re-start your
system.
Target system:
152
WIN
SCO
QNX
NET-0002: ILLEGAL VERSION
EDIABAS_NET_0002
Meaning:
Illegal version of NET<Protocol>32.DLL.
Causes:
The version of NET<Protocol>32.DLL does not match
the
version
of
the
EDIABAS
components
XREMOT32.DLL or IFHSRV32.EXE.
Error correction: Re-install the required EDIABAS version.
Target system:
WIN
SCO
QNX
64
EDIABAS - ERROR REFERENCE
153
NET-0003: INITIALIZATION ERROR
EDIABAS_NET_0003
Meaning:
Error when initializing the network.
Causes:
The network software cannot be simultaneously
operated by several clients (EDIABAS and BestView).
Error correction: Terminate EDIABAS or BestView.
Target system:
154
WIN
SCO
QNX
EDIABAS_NET_0004
NET-0004: ILLEGAL CALL
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error still happens to
occur, please contact SOFTING.
Target system:
155
WIN
SCO
QNX
EDIABAS_NET_0005
NET-0005: NO SUPPORT
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error still happens to
occur, please contact SOFTING.
Target system:
WIN
SCO
QNX
65
EDIABAS - ERROR REFERENCE
156
NET-0006: ACCESS DENIED
EDIABAS_NET_0006
Meaning:
The network access is denied.
Causes:
The network software cannot be simultaneously
operated by the client (EDIABAS or BestView) and
server (IFH-Server).
Error correction: Check the value of the EDIABAS configuration element
Interface, and terminated the client or server.
Target system:
157
WIN
SCO
QNX
NET-0007:SYSTEM ERROR
EDIABAS_NET_0007
Meaning:
Resource problem of the operating system.
Causes:
The applications require too many system resources.
Error correction: If this error repeatedly occurs, terminate other
application programs. If this error is still not corrected,
re-start your system.
Target system:
158
WIN
SCO
QNX
NET-0008: NETWORK ERROR
EDIABAS_NET_0008
Meaning:
General network problem.
Causes:
The network cannot be correctly operated.
Error correction: If this error repeatedly occurs, re-start the application
program. If this error is still not corrected, re-start your
system.
Target system:
WIN
SCO
QNX
66
EDIABAS - ERROR REFERENCE
159
EDIABAS_NET_0009
NET-0009: TIMEOUT
Meaning:
Communication partner does not respond.
Causes:
The communication setup or the communication with
the communication partner is not possible.
The communication partner is known in the network.
Error correction: Check the transmission medium.
Check whether the communication partner properly
runs.
Check whether the IFH server runs on the system of the
communication partner.
Check whether the EDIABAS configuration element
Port of the communication partner agrees with the own
system.
If this error continues to occur, re-start the application.
Target system:
160
WIN
SCO
QNX
NET-0010: BUFFER OVERFLOW
EDIABAS_NET_0010
Meaning:
The error indicates an illegal EDIABAS program state.
Causes:
A program result cannot be processed.
Error correction: Not possible by the user. If this error happens to occur,
please contact SOFTING.
Target system:
WIN
SCO
QNX
67
EDIABAS - ERROR REFERENCE
161
NET-0011: ALREADY CONNECTED
EDIABAS_NET_0011
Meaning:
Communication could not be established.
Causes:
The connection to the communization partner is already
established.
Error correction: If this error repeatedly occurs, re-start the application
program. If the error is still not corrected, re-start your
system.
Target system:
162
WIN
SCO
QNX
NET-0012: NO CONNECTION
EDIABAS_NET_0012
Meaning:
No connection to the communication partner.
Causes:
Communication with the communication partner is not
possible, since no connection exists.
Error correction: If this error repeatedly occurs, re-start the application
program. If the error is still not corrected, re-start your
system.
Target system:
163
WIN
SCO
QNX
NET-0013: CONNECTION DISTURBED
EDIABAS_NET_0013
Meaning:
Connection to the communication partner disturbed.
Causes:
Communication with the communication partner is
disturbed.
Error correction: Check the transmission medium.
Check whether the communication partner properly
runs.
If the error is still not corrected, re-start your system
Target system:
WIN
SCO
QNX
68
EDIABAS - ERROR REFERENCE
164
NET-0014: CONNECTION ABORTED
EDIABAS_NET_0014
Meaning:
No connection to the communication partner.
Causes:
Communication was aborted by the communication
partner.
Error correction: Check the communication partner, and re-start the
application program.
Target system:
165
WIN
SCO
QNX
NET-0015: HOST NOT FOUND
EDIABAS_NET_0015
Meaning:
The other communication partner or its network address
couldn't be found.
Causes:
Invalid EDIABAS configuration element RemoteHost.
Error correction: Check
the
EDIABAS
configuration
element
RemoteHost, and re-start the application program
Target system:
166
WIN
SCO
QNX
EDIABAS_NET_0016
NET-0016: HOST ERROR
Meaning:
Communication partner couldn't be reached.
Causes:
Communication setup or communication with the
communication partner is not possible.
The communication partner is known in the network.
Error correction: Check whether the communication partner properly
runs.
Check the EDIABAS configuration element Port.
Target system:
WIN
SCO
QNX
69
EDIABAS - ERROR REFERENCE
167
EDIABAS_NET_0017
NET-0017: PROTOCOL NOT
AVAILABLE
Meaning:
Protocol or network manager NET<Protocol>32.DLL
not available.
Causes:
Erroneous
EDIABAS
configuration
element
NetworkProtocol or missing NET<Protocol>32.DLL in
the EDIABAS\program directory.
Error correction: Check
the
EDIABAS
NetworkProtocol.
EDIABAS must be
configuration value.
Target system:
168
WIN
SCO
configuration
re-installed
with
the
element
correct
QNX
EDIABAS_NET_0018
NET-0018: UNKNOWN PROTOCOL
Meaning:
Unknown network protocol.
Causes:
Unassigned
EDIABAS
NetworkProtocol.
configuration
element
Error correction: Assign the network protocol to be used (e.g. TCP for
TCP/IP) to the EDIABAS configuration element
NetworkProtocol.
Target system:
169
WIN
SCO
QNX
NET-0019: UNKNOWN SERVICE
EDIABAS_NET_0019
Meaning:
Unknown network service or port.
Causes:
Unassigned EDIABAS configuration element Port.
Error correction: Assign the port number to be used to the EDIABAS
configuration element Port. The port number of the
communication partner must agree with that of the own
system
Target system:
WIN
SCO
QNX
70
EDIABAS - ERROR REFERENCE
170
EDIABAS_NET_0020
NET-0020: UNKNOWN HOST
Meaning:
Unknown communication partner.
Causes:
Unassigned
RemoteHost.
EDIABAS
configuration
element
Error correction: Assign the host name or the host address of the
communication partner to the EDIABAS configuration
element RemoteHost.
Target system:
171
WIN
SCO
QNX
NET-0021: SERVER NOT FOUND
EDIABAS_NET_0021
Meaning:
Communication partner is not avilable.
Causes:
IFH server not running
Error correction: Check IFH server is running
Target system:
172
WIN
SCO
QNX
NET-0022: SECURITY ERROR
EDIABAS_NET_0022
Meaning
During communication a security problem occured
Causes:
Missing access rights
Error correction: Check access rights
Target system:
WIN
SCO
QNX
71
EDIABAS - ERROR REFERENCE
4.5. Applikation
EDIABAS_RUN_0000
250
RUN-0000
..
..
..
349
RUN-0099
EDIABAS_RUN_0099
Meaning:
No valid status in SGBD.
Causes:
Error was set by SGBD.
Error correction: Contact the devolper of the ECU description file.
Target system:
WIN
SCO
QNX
72
EDIABAS - ERROR REFERENCE
A.
References
[1]
EDIABAS: API Interface Description
[2]
EDIABAS: User Manual
73
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement