MS-168XXXX CB report

MS-168XXXX CB report
Page 2 of 61
Report No.:
11016568 001
Copy of marking plate:
Note: The above labels are draft of artwork for marking plates pending approval by National
Certification Bodies and it shall not be affixed to products prior to such approval.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 3 of 61
Report No.:
11016568 001
Summary of testing:
The manufacturer specified maximum ambient temperature as 40°C.
Highest load for this equipment is to copy files between HDD and memory card, connect to internet by RJ-45
port, play a video CD. Adjust LCD panel with max. brightness and speaker with max. volume. Add dummy
loads of 2.5W for each USB port, charging an empty battery pack.
USB ports were compled with sub-clause 2.5 limited power source.
CPU information: Intel, Merom Core 2 Duo / Penryn processor, 2.4GHz.
There are two main boards provided for this Notebook, P/N MS-16821 and MS-16831,the big difference as
below:
-
Main board MS-16821: without HDMI port, 2 core chips used.
-
Main board MS-16831: has HDMI port, 1 core chip used.
-
Other critical components, see appended table 1.5.1 for details.
Particulars: test item vs. test requirements
Equipment mobility .......................................: Transportable equipment
Operating condition .......................................: Continuous
Mains supply tolerance (%) ...........................: No direct mains connection
Tested for IT power systems ........................: No
IT testing, phase-phase voltage (V) ..............: N/A
Class of equipment .......................................: III
Mass of equipment (kg).................................: 2.5
Protection against ingress of water ..............: IPX0
Test case verdicts
Test case does not apply to the test object ..: N/A
Test item does meet the requirement ..........: P(ass)
Test item does not meet the requirement ....: F(ail)
Testing
Date of receipt of test item ...........................: Apr., 2009
Date(s) of performance of test .....................: Apr. – May, 2009
General remarks
”This report is not valid as a CB Test Report unless appended by an approved CB Testing
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02”.
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
The manufacturer's declaration, that the samples tested represent the products from each factory, is
available
Comments:
Summary of compliance with National Differences (for explanation of codes see below):
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 4 of 61
Report No.:
11016568 001
EU Group Differences, EU Special National Conditions, EU A-Deviations, AR, AT, AU, BE, CA, CH, CN, CZ,
DE, FR, GB, GR, HU, IL, IN, IT, KE, KR, MY, NL, PL, SG, SI, SK, US.
AR=Argentina, AT=Austria, AU=Australia, BE=Belgium, CA=Canada, CH=Switzerland, CN=China,
CZ=Czech Republic, DE=Germany, DK=Denmark, FI=Finland, FR=France, GB=United Kingdom,
GR=Greece, HU=Hungary, IL=Israel, IN=India, IT=Italy, KE=Kenya, KR=Korea, MY=Malaysia, NL=The
Netherlands, NO=Norway, PL=Poland, SE=Sweden, SG=Singapore, SI=Slovenia, SK=Slovakia, US=United
States of America.
For National Differences see end of this test report.
Factories:
1.
Micro-Star Int’l Co., Ltd.
69, Li-De St., Chung Ho City, Taipei Hsien 235 Taiwan
2.
Micro-Star Int'l Co., Ltd.
488 Ban Nan St., Chung Ho City, Taipei Hsien 235 Taiwan
3.
MSI ELECTRONICS (KUNSHAN) CO., LTD.
88E QIANJIN Rd., Kunshan City, Jiangsu 215300, P.R. China
4.
MSI Computer (Shenzhen) Co., Ltd.
Longma Information Technology, Industrial Park, Tangtou Village, Shiyan Town, Baoan District,
Shenzhen, Guangdong 518108, P.R. China
Definition of variables:
Variable:
Range of variable:
Content:
x
0-9, A-Z, a-z or blank
Marketing purpose, no technical differences
General product information:
The equipment is Notebook Computer for general office use.
Connectors arrangment:
-
Rear side: 2 USB ports. D-sub port, DC-in port, HDMI port (Main board MS-16831 only).
-
Right side: 1 USB port.
-
Left side: PCMCIA slot, Card reader slot, 2 Audio ports, RJ-45 LAN port.
The external power adapters are approved products which were CB-scheme evaluated according to IEC
60950-1:2001, for detail information see appended table 1.5.1.
This report contains all national deviations shown on next page as the class III equipment itself is subject of
this CB report, but CB countries should investigate this matter for external adapter while the equipment
under test is submitted for national approval.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 5 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1
GENERAL
P
1.5
Components
P
1.5.1
General
See below.
P
Comply with IEC 60950 or relevant component
standard
See appended table 1.5.1.
P
1.5.2
Evaluation and testing of components
Components not covered by
IEC standards are tested under
the conditions present in the
equipment.
P
1.5.3
Thermal controls
1.5.4
Transformers
1.5.5
Interconnecting cables
N/A
1.5.6
Capacitors in primary circuits ...............................:
N/A
1.5.7
Double insulation or reinforced insulation bridged
by components
N/A
1.5.7.1
General
N/A
1.5.7.2
Bridging capacitors
N/A
1.5.7.3
Bridging resistors
N/A
1.5.7.4
Accessible parts
N/A
1.5.8
Components in equipment for IT power systems
N/A
1.6
Power interface
1.6.1
AC power distribution systems
1.6.2
Input current
1.6.3
Voltage limit of hand-held equipment
N/A
1.6.4
Neutral conductor
N/A
1.7
Marking and instructions
1.7.1
Power rating
N/A
No insulation transformer.
N/A
P
N/A
See appended table.
P
P
See below.
P
Rated voltage(s) or voltage range(s) (V) .............: 19V (no direct connection to
mains supply)
Symbol for nature of supply, for d.c. only .............: d.c. symbol used.
N/A
P
Rated frequency or rated frequency range (Hz) ..:
N/A
Rated current (mA or A) ......................................: 3.42A (no direct connection to
mains supply)
N/A
Manufacturer’s name or trademark or identification See copy of marking plates.
mark .....................................................................:
TRF No.:IECEN60950_1B
P
TRF originator: SGS Fimko
Page 6 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Type/model or type reference...............................: See copy of marking plates.
Symbol for Class II equipment only .....................:
Verdict
P
N/A
Other symbols ......................................................: Additional symbols or markings
do not give rise to
misunderstanding.
Certification marks ...............................................: See copy of marking plates.
N/A
1.7.2
Safety instructions
1.7.3
Short duty cycles
N/A
1.7.4
Supply voltage adjustment ...................................:
N/A
Methods and means of adjustment; reference to
installation instructions .........................................:
N/A
1.7.5
Power outlets on the equipment ..........................:
N/A
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) .........................:
N/A
1.7.7
Wiring terminals
N/A
1.7.7.1
Protective earthing and bonding terminals ..........:
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
1.7.8.1
Identification, location and marking .....................: The marking of the stand-by
switch is located that indication
of function clearly.
1.7.8.2
Colours ...............................................................:
1.7.8.3
Symbols according to IEC 60417 .........................: Marking for stand-by switch
according IEC 60417-1, No.
5009.
1.7.8.4
Markings using figures ........................................:
N/A
1.7.9
Isolation of multiple power sources .....................:
N/A
1.7.10
IT power distribution systems
N/A
1.7.11
Thermostats and other regulating devices
N/A
1.7.12
Language(s) .........................................................: Marking label and User’s
manual are in English. Versions
in other languages will be
provided when national
certificate approval.

1.7.13
Durability
Compliance.
P
1.7.14
Removable parts
No required markings placed
on removable parts.
P
TRF No.:IECEN60950_1B
Safety instructions are provided
in user’s manual.
P
See below.
P
P
P
N/A
P
TRF originator: SGS Fimko
Page 7 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
1.7.15
Replaceable batteries
Provided in user’s manual.
Language(s)..........................................................: English.
Verdict
P

1.7.16
Operator access with a tool ..................................:
N/A
1.7.17
Equipment for restricted access locations ............:
N/A
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
2.1.1.1
Access to energized parts
N/A
Test by inspection ................................................:
N/A
Test with test finger ..............................................:
N/A
Test with test pin ..................................................:
N/A
Test with test probe .............................................:
N/A
2.1.1.2
Battery compartments .........................................: No TNV.
N/A
2.1.1.3
Access to ELV wiring
N/A
The equipment is supplied from
an approved power adaptor or
battery pack that provides only
SELV.
Working voltage (Vpeak or Vrms); minimum
distance (mm) through insulation
P

2.1.1.4
Access to hazardous voltage circuit wiring
2.1.1.5
Energy hazards ....................................................:
2.1.1.6
Manual controls
N/A
2.1.1.7
Discharge of capacitors in equipment
N/A
N/A
P
Time-constant (s); measured voltage (V) .............:

2.1.2
Protection in service access areas
N/A
2.1.3
Protection in restricted access locations
N/A
2.2
SELV circuits
2.2.1
General requirements
2.2.2
Voltages under normal conditions (V) ..................: 42.4V peak or 60Vd.c. are not
exceeded in SELV circuit under
normal operation.
TRF No.:IECEN60950_1B
P
The secondary circuits were
tested as SELV. See 2.2.1 to
2.2.4.
P
P
TRF originator: SGS Fimko
Page 8 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
2.2.3
Voltages under fault conditions (V).......................: Single fault did not cause
excessive voltage in accessible
SELV circuits. Limits of 71V
peak and 120Vd.c. were not
exceeded within 0.2s and limits
42.4V peak and 60Vd.c. were
not exceeded for longer than
0.2 s.
2.2.3.1
Separation by double insulation or reinforced
insulation (method 1)
N/A
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit
(method 3)
N/A
2.2.4
Connection of SELV circuits to other circuits........: See 2.2.2, 2.2.3, 2.3 and 2.4.
2.3
TNV circuits
N/A
2.3.1
Limits
N/A
2.3.2
2.3.3
Result – Remark
P
P
Type of TNV circuits .............................................:

Separation from other circuits and from accessible
parts
N/A
Insulation employed..............................................:

Separation from hazardous voltages
N/A
Insulation employed..............................................:
2.3.4
Verdict

Connection of TNV circuits to other circuits
N/A
Insulation employed..............................................:

2.3.5
Test for operating voltages generated externally
2.4
Limited current circuits
2.4.1
General requirements
See below.
P
2.4.2
Limit values
See below.
P
N/A
P
Frequency (Hz) .....................................................: See appended table 2.4.2

Measured current (mA).........................................: See appended table 2.4.2

Measured voltage (V) ...........................................: See appended table 2.4.2

Measured capacitance (µF) ..................................: Less than 0.45µC.

2.4.3
Connection of limited current circuits to other
circuits
P
2.5
Limited power sources
P
Inherently limited output
N/A
TRF No.:IECEN60950_1B
Complied.
TRF originator: SGS Fimko
Page 9 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Impedance limited output
See appended table for USB
ports.
Verdict
P
Overcurrent protective device limited output
N/A
Regulating network limited output under normal
operating and single fault condition
N/A
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N/A
Output voltage (V), output current (A), apparent
See appended table.
power (VA)............................................................:

Current rating of overcurrent protective device (A)

2.6
Provisions for earthing and bonding
N/A
2.6.1
Protective earthing
N/A
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
2.6.3.1
General
N/A
2.6.3.2
Size of protective earthing conductors
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:
2.6.3.3
Size of protective bonding conductors

N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:

2.6.3.4
Resistance (Ω) of earthing conductors and their
terminations, test current (A) ................................:
N/A
2.6.3.5
Colour of insulation ...............................................:
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type and nominal thread
diameter (mm) ......................................................:

2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors
and protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 10 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
N/A
2.7.1
Basic requirements
N/A
Instructions when protection relies on building
installation
N/A
2.7.2
Faults not covered in 5.3
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ..........:
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ...............................:
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ..............................................:
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
2.9.1
Properties of insulating materials
2.9.2
Humidity conditioning
Humidity (%) ........................................................:
TRF No.:IECEN60950_1B
Result – Remark
Verdict
P
The unit is supplied from an
approved power supply or
battery pack that provides
SELV. Only SELV and limited
current circuit inside the unit.
P
N/A

TRF originator: SGS Fimko
Page 11 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
Temperature (°C) .................................................:

2.9.3
Grade of insulation
P
2.10
Clearances, creepage distances and distances through insulation
P
2.10.1
General
P
2.10.2
Determination of working voltage
N/A
2.10.3
Clearances
N/A
2.10.3.1
General
N/A
2.10.3.2
Clearances in primary circuits
N/A
2.10.3.3
Clearances in secondary circuits
N/A
2.10.3.4
Measurement of transient voltage levels
N/A
2.10.4
Creepage distances
N/A
CTI tests ...............................................................:
The unit is supplied from an
approved power supply or
battery pack that provides
SELV. Only SELV and limited
current circuit inside the unit.

2.10.5
Solid insulation
N/A
2.10.5.1
Minimum distance through insulation
N/A
2.10.5.2
Thin sheet material
N/A
2.10.5.3
Number of layers (pcs) .........................................:

Electric strength test

Printed boards
N/A
Distance through insulation
N/A
Electric strength test for thin sheet insulating
material

Number of layers (pcs) .........................................:
N/A
Wound components
N/A
Number of layers (pcs) .........................................:
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ..................................:
N/A
2.10.6
Coated printed boards
N/A
2.10.6.1
General
N/A
2.10.6.2
Sample preparation and preliminary inspection
N/A
2.10.6.3
Thermal cycling
N/A
2.10.6.4
Thermal ageing (°C) .............................................:
N/A
2.10.6.5
Electric strength test
2.10.5.4
TRF No.:IECEN60950_1B

TRF originator: SGS Fimko
Page 12 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
2.10.6.6
Abrasion resistance test
Result – Remark
N/A
Electric strength test
2.10.7
2.10.8
Verdict

Enclosed and sealed parts ...................................:
N/A
Temperature T1=T2 + Tma – Tamb +10K (°C)....:
N/A
Spacings filled by insulating compound................:
N/A
Electric strength test

2.10.9
Component external terminations
N/A
2.10.10
Insulation with varying dimensions
N/A
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring which is PVC
insulated, rated VW-1, minimum
80°C. Internal wiring gauge is
suitable for current intended to
be carried.
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges, which could damage
the insulation.
P
3.1.3
Securing of internal wiring
Internal wires are secured
reliable so that a loosening of
the terminal connection is
unlikely.
P
3.1.4
Insulation of conductors
The insulation of the individual
conductors is suitable for the
application and the working
voltage. For the insulation
material see 3.1.1.
P
3.1.5
Beads and ceramic insulators
N/A
3.1.6
Screws for electrical contact pressure
N/A
3.1.7
Insulating materials in electrical connections
N/A
3.1.8
Self-tapping and spaced thread screws
N/A
3.1.9
Termination of conductors
N/A
10 N pull test
N/A
3.1.10
Sleeving on wiring
N/A
3.2
Connection to an a.c. mains supply or a d.c. mains supply
N/A
3.2.1
Means of connection ............................................:
N/A
3.2.1.1
Connection to an a.c. mains supply
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 13 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
Number of conductors, diameter (mm) of cable
and conduits ........................................................:
Verdict

3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
Type......................................................................:
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:


3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ........................:

Longitudinal displacement (mm) ..........................:

3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
D (mm); test mass (g) ..........................................:

Radius of curvature of cord (mm).........................:

3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply
cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
2
area (mm )............................................................:
3.3.5
Wiring terminal sizes
Rated current (A), type and nominal thread
diameter (mm) .....................................................:

N/A

3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 14 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
3.4.1
General requirement
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Single-phase equipment and d.c. equipment
N/A
3.4.7
Three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
3.5
Interconnection of equipment
3.5.1
General requirements
3.5.2
Types of interconnection circuits ..........................: SELV and LCC.
3.5.3
ELV circuits as interconnection circuits
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Angle of 10°
Result – Remark
Verdict
P
See below.
P
P
N/A
Compliance.
P
Test: force (N).......................................................:
N/A
4.2
Mechanical strength
4.2.1
General
4.2.2
Steady force test, 10 N
N/A
4.2.3
Steady force test, 30 N
N/A
4.2.4
Steady force test, 250 N
4.2.5
Impact test
N/A
Fall test
N/A
Swing test
N/A
P
No hazards after tests.
Compliance.
P
P
4.2.6
Drop test
Compliance.
P
4.2.7
Stress relief test
Compliance at 80°C.
P
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ...........................:
N/A
High pressure lamps
N/A
4.2.9
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 15 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
4.2.10
Wall or ceiling mounted equipment; force (N) .....:
4.3
Design and construction
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ...............:
N/A
4.3.3
Adjustable controls
N/A
4.3.4
Securing of parts
Electrical and mechanical
connections can be expected
to withstand usual mechanical
stress.
P
4.3.5
Connection of plugs and sockets
Mismatch of connectors were
prevented by incompatible form
or location.
P
4.3.6
Direct plug-in equipment
N/A
Dimensions (mm) of mains plug for direct plug-in :
N/A
Torque and pull test of mains plug for direct
plug-in; torque (Nm); pull (N) ................................:
N/A
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
N/A
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids.................................................:
N/A
Quantity of liquid (l) ...............................................:
N/A
Flash point (°C).....................................................:
N/A
N/A
P
Edges and corners of the
enclosure are rounded.
For results see appended table
5.3.
P
P
4.3.13
Radiation; type of radiation ..................................: See below.
P
4.3.13.1
General
P
4.3.13.2
Ionizing radiation
4.3.13.3
4.3.13.4
See below.
N/A
Measured radiation (pA/kg) .................................:

Measured high-voltage (kV) ................................:

Measured focus voltage (kV) ...............................:

CRT markings .....................................................:

Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification ........................................................:
N/A
Human exposure to ultraviolet (UV) radiation ......:
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 16 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
4.3.13.5
Laser (including LEDs)
For ODD, which was approved
component and evaluated
according to relevant standard
for laser product.
Verdict
P
Others are indicating LEDs
used.
Laser class ...........................................................: Class 1.

4.3.13.6
Other types ..........................................................:
4.4
Protection against hazardous moving parts
4.4.1
General
The rotating part of the build-in
DC fan is protected by the
enclosure. Other motors only
used in approved components
and are no accessible to the
user.
P
4.4.2
Protection in operator access areas
See above.
P
4.4.3
Protection in restricted access locations
N/A
4.4.4
Protection in service access areas
N/A
4.5
Thermal requirements
4.5.1
Maximum temperatures
N/A
P
P
See appended table 4.5.1.
Normal load condition per Annex L.......................: See Annex L.
P
P
4.5.2
Resistance to abnormal heat
4.6
Openings in enclosures
P
4.6.1
Top and side openings
N/A
N/A
Dimensions (mm) ................................................:
4.6.2

Bottoms of fire enclosures
N/A
Construction of the bottom ...................................:
4.6.3
Doors or covers in fire enclosures
4.6.4
Openings in transportable equipment
4.6.5
Adhesives for constructional purposes

N/A
See appended table.
P
N/A
Conditioning temperature (°C)/time (weeks) ........:

4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
See below.
P
Method 1, selection and application of
components wiring and materials
Use of materials with the
required flammability classes.
P
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 17 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Method 2, application of all of simulated fault
condition tests
Verdict
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following parts:
P
- Components in secondary
(not supplied by LPS)
- Insulated wiring
The fire enclosure is required.
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Materials
4.7.3.1
General
See appended table 1.5.1 for
PCB.
P
4.7.3.2
Materials for fire enclosures
See appended table 1.5.1 for
enclosure material.
P
4.7.3.3
Materials for components and other parts outside
fire enclosures
4.7.3.4
Materials for components and other parts inside
fire enclosures
4.7.3.5
Materials for air filter assemblies
N/A
4.7.3.6
Materials used in high-voltage components
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
5.1
Touch current and protective conductor current
N/A
5.1.1
General
N/A
5.1.2
Equipment under test (EUT)
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
N/A
P
N/A
Internal components except
small parts are V-2 or better.
P
P
Test voltage (V) ...................................................:

Measured touch current (mA) ..............................:

Max. allowed touch current (mA) .........................:

Measured protective conductor current (mA) ......:

Max. allowed protective conductor current (mA) .:

5.1.7
Equipment with touch current exceeding 3.5 mA :
N/A
5.1.8
Touch currents to and from telecommunication
networks and cable distribution systems and from
telecommunication networks
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 18 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
5.1.8.1
Limitation of the touch current to a
telecommunication network and a cable
distribution system
Result – Remark
Verdict
N/A
Test voltage (V) ...................................................:

Measured touch current (mA) ..............................:

Max. allowed touch current (mA) .........................:

5.1.8.2
Summation of touch currents from
telecommunication networks ................................:
N/A
5.2
Electric strength
N/A
5.2.1
General
N/A
5.2.2
Test procedure
N/A
5.3
Abnormal operating and fault conditions
5.3.1
Protection against overload and abnormal
operation
5.3.2
Motors
N/A
5.3.3
Transformers
N/A
5.3.4
Functional insulation .............................................: Results see appended table.
5.3.5
Electromechanical components
5.3.6
Simulation of faults
5.3.7
Unattended equipment
5.3.8
Compliance criteria for abnormal operating and
fault conditions
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
P
See below.
P
P
N/A
Results see appended table.
P
N/A
No fire occurred. No molten
metal was emitted.
P
Test voltage (V) ...................................................:

Current in the test circuit (mA) ............................:

6.1.2.2
Exclusions.............................................................:
N/A
6.2
Protection of equipment users from overvoltages on telecommunication networks
N/A
6.2.1
Separation requirements
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 19 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
Max. output current (A) .........................................:

Current limiting method ........................................:

7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
Protection of cable distribution system service
persons, and users of other equipment
connected to the system, from hazardous
voltages in the equipment
N/A
7.2
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.3
Insulation between primary circuits and cable
distribution systems
N/A
7.3.1
General
N/A
7.3.2
Voltage surge test
N/A
7.3.3
Impulse test
N/A
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
A.1
Flammability test for fire enclosures of movable equipment having a total mass
exceeding 18 kg, and of stationary equipment (see 4.7.3.2)
A.1.1
Samples................................................................:

Wall thickness (mm) .............................................:

A.1.2
Conditioning of samples; temperature (°C) ..........:
N/A
A.1.3
Mounting of samples ............................................:
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ...............................................:
P
N/A

A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 20 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
P
A.2.1
Samples, material.................................................:

Wall thickness (mm) .............................................:

A.2.2
Conditioning of samples
N/A
A.2.3
Mounting of samples ...........................................:
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C ...................................................:

A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

Alternative test acc. to IEC 60695-2-2, cl. 4 and 8
N/A
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position ................................................................:

Manufacturer ........................................................:

Type .....................................................................:

Rated values .......................................................:

B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) .............................................:

Electric strength test: test voltage (V) ..................:

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 21 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
B.6
Running overload test for d.c. motors in
secondary circuits
N/A
B.7
Locked-rotor overload test for d.c. motors in secondary circuits
N/A
B.7.1
Test procedure
N/A
B.7.2
Alternative test procedure; test time (h)................:
N/A
B.7.3
Electric strength test
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V) ...........................................:
C
Verdict

ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
N/A
Position ................................................................:

Manufacturer ........................................................:

Type .....................................................................:

Rated values .......................................................:

Method of protection .............................................:

C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings ............:
N/A
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
N/A
D.1
Measuring instrument
N/A
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10)
N/A
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V) .......:
N/A
G.2.1
AC mains supply
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 22 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
G.2.2
DC mains supply
N/A
G.3
Determination of telecommunication network
transient voltage (V)..............................................:
N/A
G.4
Determination of required withstand voltage (V)...:
N/A
G.5
Measurement of transient levels (V).....................:
N/A
G.6
Determination of minimum clearances .................:
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
N/A
Metal used ...........................................................:
Verdict

K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) .........:
N/A
K.3
Thermostat endurance test; operating voltage
(V) .......................................................................:
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................:
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.1)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
TRF No.:IECEN60950_1B
See copy of marking plate.
P
P
TRF originator: SGS Fimko
Page 23 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
M.3.1.1
Frequency (Hz) ....................................................:

M.3.1.2
Voltage (V) ...........................................................:

M.3.1.3
Cadence; time (s), voltage (V) .............................:

M.3.1.4
Single fault current (mA) .......................................:

M.3.2
Tripping device and monitoring voltage ................:
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V)...........................................:
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 2.10.3.4, 6.2.2.1, 7.3.2 and
clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, BIBLIOGRAPHY
N/A
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A
P

U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 24 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N/A
V.1
Introduction
N/A
V.2
TN power distribution systems
N/A
V.3
TT power systems
N/A
V.4
IT power systems
N/A
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS
(see clause C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus .....................................................:
N/A
Y.2
Mounting of test samples .....................................:
N/A
Y.3
Carbon-arc light-exposure apparatus ..................:
N/A
Y.4
Xenon-arc light exposure apparatus ....................:
N/A
TRF No.:IECEN60950_1B
Result – Remark
Verdict
TRF originator: SGS Fimko
Page 25 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
CENELEC COMMON MODIFICATIONS [C],
SPECIAL NATIONAL CONDITIONS [S] AND A-DEVIATIONS (NATIONAL DEVIATIONS) [A]
(EN 60950-1:2001, Annex ZB and Annex ZC)
General
C: Delete all the "country" notes in the reference
document according to the following list:
1.1.5
Note 2
1.7.2
Note 4
2.2.3
Note
2.3.3
Note 1, 2
2.10.3.1 Note 4
3.2.5.1 Note 2
4.7.3.1 Note 2
6.2.2
Note
7
Note 4
G2.1
Note 1, 2
1.5.8
1.7.12
2.2.4
2.3.4
3.2.1.1
4.3.6
6.1.2.1
6.2.2.1
7.1
Annex H
Note 2
Note 2
Note
Note 2,3
Note
Note 1,2
Note
Note 2
Note
Note 2
1.6.1
2.6
2.3.2
2.7.1
3.2.3
4.7.2.2
6.1.2.2
6.2.2.2
Deleted.
Verdict
P
P
Note
Note
Note 2, 7, 8
Note
Note 1, 2
Note
Note
Note
1.2.4.1
S (DK): Certain types of Class I appliances (see
3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted
into Danish socket-outlets.
No direct connection to the
mains supply.
N/A
1.5.1
A (SE, Ordinance 1990:944 and
CH, Ordinance on environmentally hazardous
substances SR 814.013, Annex 3.2, Mercury):
Add NOTE – Switches containing mercury such as
No such switch.
N/A
S (NO): Due to the IT power system used (see
annex V, Fig. V.7), capacitors are required to be
rated for the applicable line-to-line voltage
(230 V).
Class III equipment.
N/A
S (FI, NO, SE): CLASS I PLUGGABLE EQUIPMENT
intended for connection to other
equipment or a network shall, if safety relies on
connection to protective earth or if surge
suppressors are connected between the network
terminals and accessible parts, have a marking
stating that the equipment must be connected to
an earthed mains socket-outlet.
Class III equipment.
N/A
FI: "Laite on liitettävä suojamaadoituskoskettimilla Class III equipment.
varustettuun pistorasiaan"
N/A
NO: "Apparatet må tilkoples jordet stikkontakt"
Class III equipment.
N/A
SE: "Apparaten skall anslutas till jordat uttag"
Class III equipment.
N/A
A (DK, Heavy Current Regulations): Supply cords Class III equipment.
of class I equipment, which is delivered without a
plug, must be provided with a visible tag with the
following text:
N/A
thermostats, relays and level controllers are not allowed.
1.5.8
1.7.2
TYPE A
The marking text in the applicable countries shall
be as follows:
Vigtigt!
Lederen med grøn/gul isolation må kun tilsluttes
en klemme mærket
eller
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 26 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
If essential for the safety of the equipment, the
tag must in addition be provided with a diagram
which shows the connection of the other
conductors, or be provided with the following text:
"For tilslutning af de øvrige ledere, se
medfølgende instalationsvejledning."
1.7.5
1.7.5
S (DK): Socket-outlets for providing power to
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For stationary
equipment the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a.
No socket-outlets.
N/A
A (DK, Heavy Current Regulations):
Class III equipment.
shall not be fitted with socketoutlets for providing power to other equipment.
N/A
A (DE, Gesetz über technische Arbeitsmittel
Shall be evaluated during
(Gerätesicherheitsgesetz) [Law on technical
national approval.
rd
labour equipment {Equipment safety law}], of 23
rd
nd
October 1992, Article 3, 3 paragraph, 2
sentence, together with the "Allgemeine
Verwaltungsvorschrift zur Durchführung des
Zweiten Abschnitts des Gerätesicherheitsgesetzes" [General administrative regulation on
the execution of the Second Section of the
th
Equipment safety law], of 10 January 1996,
th
article 2, 4 paragraph item 2):
Directions for use with rules to prevent certain
hazards for (among others) maintenance of the
technical labour equipment, also for imported
technical labour equipment shall be written in the
German language.
N/A
CLASS II EQUIPMENT
1.7.12
NOTE: Of this requirement, rules for use even only by service
personnel are not exempted.
1.7.15
A (CH, Ordinance on environmentally hazardous
substances SR 814.013):
Annex 4.10 of SR 814.013 applies for batteries.
Battery pack and RTC battery
are in compliance with
requirements of IEC 60950-1.
N/A
Overall compliance needs to be
evaluated during the national
approval process.
A (DE, Regulation on protection against hazards This national difference was
th
by X-ray, of 8 January 1987, Article 5 [Operation deleted by A11 of EN 60950-1.
of X-ray emission source], clauses 1 to 4):
a) A licence is required by those who operate an
X-ray emission source.
b) A licence in accordance with Cl. 1 is not
required by those who operate an X-ray emission
source on which the electron acceleration voltage
does not exceed 20 kV if
1) the local dose rate at a distance of 0,1 m from
the surface does not exceed 1 µSv/h and
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 27 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated and
ii) the electron acceleration voltage must not
exceed the maximum value stipulated by
the manufacturer or importer.
c) A licence in accordance with Cl. 1 is also not
required by persons who operate an X-ray
emission source on which the electron
acceleration voltage exceeds 20 kV if
1) the X-ray emission source has been granted a
type approval and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated
ii) the device stipulated by the manufacturer or
importer guarantees that the maximum
permissible local dose rate in accordance
with the type approval is not exceeded and
iii) the electron acceleration voltage must not
exceed the maximum value stipulated by the
manufacturer or importer.
d) Furthermore, a licence in accordance with
Cl. 1 is also not required by persons who operate
X-ray emission sources on which the electron
acceleration voltage does not exceed 30 kV if
1) the X-rays are generated only by intrinsically
safe CRTs complying with Enclosure III, No. 6,
2) the values stipulated in accordance with
Enclosure III, No. 6.2 are limited by technical
measures and specified in the device and
3) it is adequately indicated on the X-ray emission
source that the X-rays generated are adequately screened by the intrinsically safe CRT.
2.2.4
S (NO): Requirements according to this annex,
1.7.2 and 6.1.2.1 apply.
N/A
2.3.2
S (NO): Requirements according to this annex,
6.1.2.1 apply.
N/A
2.3.3 and
2.3.4
S (NO): Requirements according to this annex,
1.7.2 and 6.1.2.1 apply.
N/A
2.6.3.3
S (GB): The current rating of the circuit shall be
taken as 13 A, not 16 A.
N/A
2.7.1
C: Replace the subclause as follows:
N/A
Basic requirements
To protect against excessive current, shortcircuits and earth faults in PRIMARY CIRCUITS,
protective devices shall be included either as
integral parts of the equipment or as parts of the
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 28 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
building installation, subject to the following, a), b)
and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the
requirements of 5.3 shall be included as parts of
the equipment;
b) for components in series with the mains input
to the equipment such as the supply cord,
appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided
by protective devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT TYPE B
or PERMANENTLY CONNECTED EQUIPMENT, to rely
on dedicated overcurrent and short-circuit
protection in the building installation, provided
that the means of protection, e.g. fuses or circuit
breakers, is fully specified in the installation
instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT TYPE
A the building installation shall be regarded as
providing protection in accordance with the rating
of the wall socket outlet.
S (GB): To protect against excessive currents
and short-circuits in the PRIMARY CIRCUIT OF
DIRECT PLUG-IN EQUIPMENT, protective device shall
be included as integral parts of the DIRECT PLUGIN EQUIPMENT.
N/A
2.7.2
C: Void.
Declared.
N/A
2.10.2
C: Replace in the first line "(see also 1.4.7)" by
"(see also 1.4.8)".
Replaced.
N/A
2.10.3.1
S (NO): Due to the IT power distribution system
used (see annex V, Fig. V.7), the A.C. MAINS
SUPPLY voltage is considered to be equal to the
line-to-line voltage and will remain at 230 V in
case of a single earth fault
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 29 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
3.2.1.1
Requirement – Test
S (CH): Supply cords of equipment having a
not exceeding 10 A shall be
provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of the following dimension
sheets:
Result – Remark
Verdict
N/A
RATED CURRENT
SEV 6532-2.1991, Plug type 15, 3P+N+PE 250/400 V, 10 A
SEV 6533-2.1991, Plug type 11, L+N
250 V, 10 A
SEV 6534-2.1991, Plug type 12, L+N+PE 250 V, 10 A
In general, EN 60309 applies for plugs for
currents exceeding 10 A. However, a 16 A plug
and socket-outlet system is being introduced in
Switzerland, the plugs of which are according to
the following dimension sheets, published in
February 1998:
SEV 5932-2.1998, Plug type 25, 3L+N+PE 230/400 V, 16 A
SEV 5933-2.1998, Plug type 21, L+N
250 V, 16 A
SEV 5934-2.1998, Plug type 23, L+N+PE 250 V, 16 A
S (DK): Supply cords of single-phase equipment
having a rated current not exceeding 13 A shall
be provided with a plug according to the Heavy
Current Regulations, Section 107-2-D1.
N/A
provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against
indirect contact is required according to the wiring
rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
CLASS I EQUIPMENT
If ply-phase equipment and single-phase
equipment having a RATED CURRENT exceeding
13 A is provided with a supply cord with a plug,
this plug shall be in accordance with the Heavy
Current Regulations, Section 107-2-D1 or
EN 60309-2.
S (ES): Supply cords of single-phase equipment
having a rated current not exceeding 10 A shall
be provided with a plug according to
UNE 20315:1994.
N/A
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be
provided with a plug according to
UNE-EN 50075:1993.
provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against
indirect contact is required according to the wiring
rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
CLASS I EQUIPMENT
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
S (GB): Apparatus which is fitted with a flexible
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 30 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
cable or cord and is designed to be connected to
a mains socket conforming to BS 1363 by means
of that flexible cable or cord and plug, shall be
fitted with a 'standard plug' in accordance with
Statutory Instrument 1768:1994 – The Plugs and
Socket etc. (Safety) Regulations 1994, unless
exempted by those regulations.
NOTE – 'Standard plug' is defined in SI 1768:1994 and
essentially means an approved plug conforming to BS 1363
or an approved conversion plug.
S (IE): Apparatus which is fitted with a flexible
cable or cord and is designed to be connected to
a mains socket conforming to I.S. 411 by means
of that flexible cable or cord and plug, shall be
fitted with a 13 A plug in accordance with
Statutory Instrument 525:1997 – National
Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic
Use) Regulations 1997.
3.2.3
C: Delete Note 1 and in Table 3A, delete the
conduit sizes in parentheses.
3.2.5.1
C: Replace
N/A
Deleted.
N/A
N/A
"60245 IEC 53" by "H05 RR-F";
"60227 IEC 52" by "H03 VV-F or H03 VVH2-F";
"60227 IEC 53" by "H05 VV-F or H05 VVH2-F2".
In Table 3B, replace the first four lines by the
following:
Up to and including 6
2)
Over 6 up to and including 10 (0,75)
3)
Over 10 up to and including 16 (1,0)
1)
0,75
1,0
1,5
In the Conditions applicable to Table 3B delete
1)
the words "in some countries" in condition .
In Note 1, applicable to Table 3B, delete the
second sentence.
3.2.5.1
S (GB): A power supply cord with conductor of
2
1,25 mm is allowed for equipment with a rated
current over 10 A and up to and including 13 A.
3.3.4
C: In table 3D, delete the fourth line: conductor
sizes for 10 to 13 A, and replace with the
following:
"Over 10 up to and including 16
1,5 to 2,5
N/A
Deleted.
N/A
1,5 to 4"
Delete the fifth line: conductor sizes for 13 to
16 A.
3.3.4
S (GB): The range of conductor sizes of flexible
cords to be accepted by terminals for equipment
with a RATED CURRENT of over 10 A up to and
including 13 A is:
2
2
- 1,25 mm to 1,5 mm nominal cross-sectional
area.
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 31 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
4.3.6
S (GB): The torque test is performed using a
socket outlet complying with BS 1363 and the
plug part of DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3,
12.9, 12.11, 12.12, 12.16 and 12.17, except that
the test of 12.17 is performed at not less than
125 °C.
N/A
S (IE): DIRECT PLUG-IN EQUIPMENT is known as
plug similar devices. Such devices shall comply
with Statutory Instrument 526:1997 – National
Standards Authority of Ireland (Section 28)
(Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
4.3.13.6
C: Add the following note:
Result – Remark
Added.
Verdict
N/A
NOTE Attention is drawn to 1999/519/EC: Council
Recommendation on the limitation of exposure of the general
public to electromagnetic fields 0 Hz to 300 GHz. Standards
taking into account this recommendation are currently under
development.
6.1.2.1
S (FI, NO, SE): Add the following text between
the first and second paragraph:
N/A
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that CLEARANCES
AND CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below
and in addition
- passes the tests and inspection criteria of 2.10.8
with an electric strength test of 1,5 kV multiplied
by 1,6 (the electric strength test of 2.10.7 shall be
performed using 1,5 kV), and
- is subject to ROUTINGE TESTING for electric
strength during manufacturing, using a test
voltage of 1,5 kV.
It is permitted to bridge this insulation with a
capacitor complying with EN 132400:1994,
subclass Y2.
A capacitor classified Y3 according to
EN 132400:1994, may bridge this insulation
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 32 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
under the following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
EN 132400, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in
EN 60950:2000, 6.2.2.1;
- the additional testing shall be performed on all
the test specimens as described in EN 132400;
- the impulse test of 2,5 kV is to be performed
before the endurance test in EN 132400, in the
sequence of tests as described in EN 132400.
6.1.2.2
S (FI, NO, SE): The exclusions are applicable for
N/A
PERMANENTLY CONNECTED EQUIPMENT and
PLUGGABLE EQUIPMENT TYPE B and equipment
intended to be used in a RESTRICTED ACCESS
LOCATION where equipotential bonding has been
applied, e.g. in a telecommunication centre, and
which has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is provided
with instructions for the installation of that
conductor by a service person.
7.1
S (FI, NO, SE): Requirements according to this
annex, 6.1.2.1 and 6.1.2.2 apply with the term
TELECOMMUNICATION NETWORK in 6.1.2 being
replaced by the term CABLE DISTRIBUTION SYSTEM.
N/A
G.2.1
S (NO): Due to the IT power distribution system
used (see annex V, Fig. V.7), the A.C. MAINS
SUPPLY voltage is considered to be equal to the
line-to-line voltage, and will remain at 230 V in
case of a single earth fault.
N/A
Annex H
C: Replace the last paragraph of this annex by:
N/A
At any point 10 cm from the surface of the
operator access area, the dose rate shall not
exceed 1 µSv/h (0,1 mR/h) (see note). Account is
taken of the background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete Note 2.
Annex P
C: Replace the text of this annex by:
P
See annex ZA.
Annex Q
C: Replace the title of IEC 61032 by "Protection of persons and equipment by
enclosures – Probes for verification".
N/A
Add the following notes for the standards indicated:
IEC 60127
IEC 60269-2-1
IEC 60529
IEC 61032
IEC 61140
TRF No.:IECEN60950_1B
NOTE Harmonized as EN 60127 (Series) (not modified)
NOTE Harmonized as HD 630.2.1 S4:2000 (modified)
NOTE Harmonized as EN 60529:1991 (not modified)
NOTE Harmonized as EN 61032:1998 (not modified)
NOTE Harmonized as EN 61140:2001 (not modified)
TRF originator: SGS Fimko
Page 33 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
ITU-T Recommendation K.31
NOTE in Europe, the suggested document is EN 50083-1.
Annex ZA
C: NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH
THEIR RELEVANT EUROPEAN PUBLICATIONS
P
This European Standard incorporates, by dated or undated reference, provisions
from other publications. These normative references are cited at the appropriate
places in the text and the publications are listed hereafter. For dated references,
subsequent amendments to or revisions of any of these publications apply to this
European Standard only when incorporated in it by amendment or revision. For
undated references, the latest edition of the publication referred to applies
(including amendments).
NOTE When an international publication has been modified by common modifications, indicated by
(mod), the relevant EN/HD applies.


EN 60065:1998 + corr. June 1999
EN 60073:1996
HD 566 S1:1990
HD 214 S2:1980
HD 611.4.1.S1:1992
1)
HD 21 Series
2)
HD 22 Series
EN 60309 Series
EN 60317-43:1997
EN 60320 Series
HD 384.3 S2:1995
HD 384.4.41 S2:1996
4)
EN 132400:1994
+ A2:1998 + A3:1998 + A4:2001
EN 60417-1
HD 625.1 S1:1996 + corr. Nov. 1996
EN 60695-2-2:1994
EN 60695-2-11:2001




EN 60695-11-10:1999
EN 60695-11-20:1999
EN 60730-1:2000
EN 60825-1:1994 + corr. Febr. 1995 +
A11:1996 + corr. July 1997
EN 60825-2:2000

EN 60851-3:1996
EN 60851-5:1996
EN 60851-6:1996

EN 60990:1999

EN 61965:2001
EN ISO 178:1996
EN ISO 179 Series
TRF No.:IECEN60950_1B
IEC 60050-151
IEC 60050-195
IEC 60065 (mod):1998
IEC 60073:1996
IEC 60085:1984
IEC 60112:1979
IEC 60216-4-1:1990
IEC 60227 (mod) Series
IEC 60245 (mod) Series
IEC 60309 Series
IEC 60317-43:1997
IEC 60320 (mod) Series
IEC 60364-3 (mod):1993
3)
IEC 60364-4-41 (mod):1992
IEC 60384-14:1993
IEC 60417-1
IEC 60664-1 (mod):1992
IEC 60695-2-2:1991
IEC 60695-2-11:2000
IEC 60695-2-20:1995
IEC 60695-10-2:1995
IEC 60695-11-3:2000
IEC 60695-11-4:2000
IEC 60695-11-10:1999
IEC 60695-11-20:1999
IEC 60730-1:1999 (mod)
IEC 60825-1:1993
IEC 60825-2:2000
IEC 60825-9:1999
IEC 60851-3:1996
IEC 60825-5:1996
IEC 60851-6:1996
IEC 60885-1:1987
IEC 60990:1999
IEC 61058-1:2000
IEC 61965:2000
ISO 178:1993
ISO 179 Series
TRF originator: SGS Fimko
Page 34 of 61
Report No.:
11016568 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
EN ISO 180:2000


EN ISO 527 Series

EN ISO 4892 Series

EN ISO 8256:1996

EN ISO 9773:1998


Result – Remark
Verdict
ISO 180:1993
ISO 261:1998
ISO 262:1998
ISO 527 Series
ISO 386:1984
ISO 4892 Series
ISO 7000:1989
ISO 8256:1990
ISO 9772:1994
ISO 9773:1998
ITU-T:1988 Recommendation K.17
ITU-T:2000 Recommendation K.21
1) The HD 21 series is related to, but not directly equivalent with the IEC 60227 series
2) The HD 22 series is related to, but not directly equivalent with the IEC 60245 series
3) IEC 60364-4-41:1992 is superseded by IEC 60364-4-41:2001
4) EN 132400, Sectional Specification: Fixed capacitors for electromagnetic interference suppression
and connection to the supply mains (Assessment level D), and its amendments are related to, but not
directly equivalent to IEC 60384-14
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 35 of 61
1.5.1
Report No.:
11016568 001
TABLE: list of critical components
P
Object/part no.
Manufacturer/
trademark
Type/model
Technical data
Standard
Mark(s) of
1.
conformity
AC Adapter
Li Shin
0335A1965
Input rated: 100240Vac, 50-60Hz,
1.7A
EN 60950-1:
2001+A11
TÜV, CB by
TÜV
Output rated: 19
Vdc, 3.42A min.
IEC 60950-1:
2001
Class I, 40°C
Delta
ADP-65HB BB
Input rated: 100240Vac, 50-60HZ,
1.5A
Output rated: 19
Vdc, 3.42A min.
EN 60950-1:
2001+A11
TÜV, CB by
TÜV
IEC 60950-1:
2001
Class I, 40°C, LPS
Raychem
PTC provided
for USB ports
(F1, F2 for main
board MS16821)
miniSMDC150F 6Vdc, Ih=1.5A,
It=3A
IEC/EN 60730-1 TÜV
Bourns Inc
MF-MSMF150
6Vdc, Ih=1.5A,
It=3A.
IEC/EN 60730-1 TÜV
Forcecon
DFS451205M1
0T
5Vdc, 0.4A,
4.2CFM
EN 60950-1:
2001+A11
(F2, F3 for main
board MS16831)
DC Fan
TÜV
IEC 60950-1:
2001
RTC Battery
Vic-Dawn
(Lithium)(BAT1) Enterprise Co
Ltd
CR2032
UL 1642
3Vdc, max.
abnormal charging
current 10mA,
UL
Matsushita
Electric
Industrial Co
Ltd;
Panasonic
Corp Of North
America
CR2032
UL 1642
3Vdc, max.
abnormal charging
current 10mA,
UL
V-0, overall 374 by UL 94
247.5 by 35mm,
min. 1.2mm
thickness, 85°C
UL
Enclosure
C7230P
SABIC
Innovative
plastics JAPAN
LCC
Hard Disk Drive
(Optional)
Fujitsu Ltd
TRF No.:IECEN60950_1B
MHZ2xxxBz (x= 5Vdc, 0.6A
0-9, A-Z or a-z;
z= A, H or S)
EN 60950-1:
2001+A11
TÜV
IEC 60950-1:
2001
TRF originator: SGS Fimko
Page 36 of 61
Fujitsu Ltd
MJA2xxxBA
(x=0-9 or A-Z)
5Vdc, 0.6A
Report No.:
EN 60950-1:
2001+A11
11016568 001
TÜV
IEC 60950-1:
2001
Western Digital WD series
5Vdc, 1.0A
EN 60950-1:
2001+A11
TÜV
IEC 60950-1:
2001
5Vdc, 1.1A or
HDD2yyyx (x=
A-Z, y=0-9 or A- 5Vdc, 3.3Vdc/
0.7A, 0.5A
Z)
EN 60950-1:
2001+A11
Sony Nec
AD-7580S
Rated :5Vdc,1.5A,
Laser Class 1
IEC/EN 60950- TÜV
1:2001
IEC/EN 60825-1
/A1+A2
Hitachi-LG
Date Storage
GT10N
Rated :5Vdc, 1.8A, IEC/EN 60950- TÜV
Laser Class 1
1:2001
IEC/EN 60825-1
/A1+A2
Toshiba
TS-L633
Rated :5Vdc, 1.5A
or 1.3A, Laser
Class 1
IEC/EN 60950- TÜV
1:2001
IEC/EN 60825-1
/A1+A2
Philips & LiteOn
DS-8A2S
Rated :5Vdc,1.5A,
Laser Class 1
IEC/EN 60950- TÜV
1:2001
IEC/EN 60825-1
/A1+A2
Sampo Corp.
YIVNMS0018D
11-B
I/P: 20Vdc, 740mA -max.
Toshiba
O.D.D (CD-RW
/DVD ROM
Drive)
(Optional)
DC/AC inverter
TÜV
IEC 60950-1:
2001
--
O/P: 850Vrms,
6.5mA max.
YCVT-1619IDZ-A
105°C
--
--
--
--
150pF, 2KV
--
--
Mitac
Technology
Corp.
DA-1A08MS02L
I/P: 20 dc, 850mA
max.
--
--
-
Transformer Top Nation,
Yao Sheng
(PT1)
-
Capacitor
(C13)
DC/AC inverter
-
Transformer Top Nation,
Yao Sheng
(T1)
-
Capacitor
(C3)
--
TRF No.:IECEN60950_1B
O/P: 1400Vrms,
6.5mA max.
273001051551
105°C
--
--
--
100pF, 2KV
--
--
TRF originator: SGS Fimko
Page 37 of 61
DC/AC inverter
Taiwan Sumida IV14080/T-LF
Electronics Inc
Report No.:
11016568 001
--
--
105°C
--
--
I/P: 14.4Vdc,
450mA max.
O/P: 1600Vrms,
6.5mA max.
-
Transformer Taiwan Sumida CL-14080TDZElectronics Inc LF
(T1)
-
Capacitor
(C14)
TFT LCD panel
Battery Pack
--
--
100pF, 2KV
--
--
Chi Mei
N156B3-L01,
N156B3-L02
15.6”, TFT
--
--
Samsung
LTN160AT01A01,
LTN160AT01A02,
LTN160AT01A04
16”, TFT
--
--
Celxpert
Energy Corp
BTY-L74
11.1Vdc, 4.4Ah,
40°C
EN 60950-1:
2001+A11
TÜV
IEC 60950-1:
2001
Speaker (Two
Provided)
--
--
4Ω, 2W
--
--
PCB
--
--
V-1, 105°C
UL94
UL
Note(s):
1. An asterisk indicates a mark that assures the agreed level of surveillance.
1.6.2
Fuse #
TABLE: electrical data (in normal conditions)
Irated (A)
U (V)
P (W)
I (A)
P
Ifuse (A)
Condition/status
For main board MS-16821
--
3.42
DC 19
61.94
3.26
--
DC/AC Inverter SAMPO,
YIVNMS0018D11-B
--
3.42
DC 19
62.32
3.28
--
DC/AC Inverter Mitac, DA-1A08MS02L
--
3.42
DC 19
62.32
3.28
--
DC/AC Inverter Sumida,
IV14080/T-LF
For main board MS-16831
--
3.42
DC 19
63.46
3.34
--
DC/AC Inverter SAMPO,
YIVNMS0018D11-B
--
3.42
DC 19
63.46
3.34
--
DC/AC Inverter Mitac, DA-1A08MS02L
--
3.42
DC 19
63.27
3.33
--
DC/AC Inverter Sumida,
IV14080/T-LF
Note(s):
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 38 of 61
2.1.1.5
Report No.:
11016568 001
TABLE: max. V, A, VA test
Voltage (rated)
(V)
N/A
Current (rated)
(A)
Voltage (max.)
(V)
Current (max.)
(A)
VA (max.)
(VA)
Note(s):
2.1.1.7
TABLE: discharge test
Condition
N/A
τ calculated τ measured
(s)
(s)
t u→ 0V
(s)
Comments
Note(s):
2.2.2
TABLE: Hazardous voltage measurement
Transformer
N/A
Location
max. Voltage
V peak
Voltage Limitation
Component
V d.c.
Note(s):
2.2.3
TABLE: SEL voltage measurement
Location
N/A
Voltage measured (V)
Comments
Note(s):
2.4.2
TABLE: limited current circuit measurement
Location
Voltage
(V)
Current
(mA)
P
Freq.
(kHz)
Limit
(mA)
Comments
Test for DC/AC inverter: Sampo / YIVNMS0018D11-B
Normal condition
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2-Earth
2.94
1.47
58
40.6
PT1 pin 5-6
--
--
--
--
Unit shut down immediately.
PT1 pin 5-Earth
--
--
--
--
Unit shut down immediately.
PT1 pin 6-Earth
1.86
0.93
52
36.4
C13 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 39 of 61
CN2 Pin 2-Earth
Report No.:
11016568 001
2.98
1.49
59
41.3
PT1 pin 5-6
--
--
--
--
Unit shut down immediately.
PT1 pin 5-Earth
--
--
--
--
Unit shut down immediately.
PT1 pin 6-Earth
--
--
--
--
Unit shut down immediately.
C21 shorted or C9 shorted or Q1 pin 2-6 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2-Earth
--
--
--
--
Unit shut down immediately.
PT1 pin 5-6
--
--
--
--
Unit shut down immediately.
PT1 pin 5-Earth
--
--
--
--
Unit shut down immediately.
PT1 pin 6-Earth
--
--
--
--
Unit shut down immediately.
Test for DC/AC inverter: Mitac / DA-1A08-MS02L
Normal condition
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
2.84
1.42
21
14.7
--
--
--
--
T1 pin 3-Earch
1.98
0.99
21
14.7
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 3-4
Unit shut down immediately.
C3 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
2.88
1.44
22
15.4
T1 pin 3-4
--
--
--
--
Unit shut down immediately.
T1 pin 3-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
C6 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
2.78
1.39
22
15.4
T1 pin 3-4
--
--
--
--
Unit shut down immediately.
T1 pin 3-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
R15 shorted or U1 pin 2-6 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 40 of 61
Report No.:
11016568 001
CN2 Pin 2- Earth
--
--
--
--
Unit shut down immediately.
T1 pin 3-4
--
--
--
--
Unit shut down immediately.
T1 pin 3-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
Test for DC/AC inverter: Sumida / IV14080/T-LF
Normal condition
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
2.82
1.41
47.02
32.91
--
--
--
--
T1 pin 4-Earch
1.78
0.89
55.12
38.58
T1 pin 5-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 4-5
Unit shut down immediately.
C14 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
2.98
1.49
48.62
34.03
T1 pin 4-5
--
--
--
--
Unit shut down immediately.
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 5-Earch
--
--
--
--
Unit shut down immediately.
R4 shorted or R9 shorted or Q3 pin 2-6 shorted
CN2 Pin 1-2
--
--
--
--
Unit shut down immediately.
CN2 Pin 1-Earth
--
--
--
--
Unit shut down immediately.
CN2 Pin 2- Earth
--
--
--
--
Unit shut down immediately.
T1 pin 4-5
--
--
--
--
Unit shut down immediately.
T1 pin 4-Earch
--
--
--
--
Unit shut down immediately.
T1 pin 5-Earch
--
--
--
--
Unit shut down immediately.
Note(s):
2.5
TABLE: limited power source measurement
Limits
P
Measured
Verdict
8
2.8
P
5*Uoc
10.86
P
For main board MS-16821
According to Table 2B (normal condition), For USB ports, Uoc=5.05V
current (in A)
apparent power (in VA)
For main board MS-16831
According to Table 2B (normal condition), For USB ports, Uoc=5.03V
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 41 of 61
current (in A)
apparent power (in VA)
Report No.:
11016568 001
8
2.6
P
5*Uoc
9.49
P
Note(s):
1. The all protection circuits of USB 5V output are same design, only wrong test data be written.
2.6.3.4
TABLE: ground continue test
Location
N/A
Resistance measured (mΩ) Comments
Note(s):
2.10.2
Table: working voltage measurement
Location
N/A
RMS voltage (V)
Peak voltage (V) Comments
Note(s):
2.10.3 and TABLE: clearance and creepage distance measurements
2.10.4
Clearance cl and creepage
distance dcr at/of:
Up
(V)
U r.m.s.
(V)
N/A
Required
cl (mm)
cl
(mm)
Required
dcr (mm)
dcr
(mm)
Note(s):
2.10.5
TABLE: distance through insulation measurements
Distance through insulation di at/of:
U r.m.s.
(V)
N/A
Test voltage
(V)
Required di
(mm)
di
(mm)
Note(s):
4.5.1
TABLE: maximum temperatures
P
test voltage (V) .............................................: A) DC 19V

B) Power from battery pack
t1 (°C) ..........................................................: --

t2 (°C) ..........................................................: --

Maximum temperature T of part/at:
Test condition
T (°C)
A)
allowed Tmax (°C)
B)
--
68.5
105
For main board MS-16821
PCB near U25 (CPU)
TRF No.:IECEN60950_1B
75.5
TRF originator: SGS Fimko
Page 42 of 61
Report No.:
11016568 001
PCB near U22
72.0
67.5
105
PCB near U32
81.0
75.9
105
RTC battery (BAT1)
73.8
72.4
--
H.D.D body
66.3
62.3
--
CD-ROM body
53.1
52.0
--
Battery pack body
44.2
58.4
75
T1 coil (DC/AC Inverter, Mitac / DA-1A08-MS02L)
79.2
76.2
105
Enclosure inside near U25 (plastic)
68.5
63.7
85
Enclosure outside near U25 (plastic)
62.3
57.2
75
40.0 (26.4)
40.0 (26.1)
--
80.8
--
105
40.0 (25.8)
--
--
72.8
--
105
40.0 (25.1)
--
--
Tma (Tamb)
PT1 coil (DC/AC Inverter, Sampo / YIVNMS0018D11-B)
Tma (Tamb)
T1 coil (DC/AC Inverter, Sumida / IV14080/T-LF)
Tma (Tamb)
For main board MS-16831
PCB near U13 (CPU)
70.2
69.3
105
PCB near U14
73.3
72.6
105
RTC battery (BAT1)
61.3
59.7
--
H.D.D body
51.1
56.3
--
CD-ROM body
53.6
52.6
--
Battery pack body
43.9
56.6
75
T1 coil (DC/AC Inverter, Mitac / DA-1A08-MS02L)
78.7
75.2
105
Enclosure inside near U13 (plastic)
60.6
61.2
85
Enclosure outside near U13 (plastic)
56.3
55.5
75
40.0 (26.2)
40.0 (26.9)
--
76.2
--
105
40.0 (25.9)
--
--
72.0
--
105
40.0 (25.6)
--
--
Tma (Tamb)
PT1 coil (DC/AC Inverter, Sampo / YIVNMS0018D11-B)
Tma (Tamb)
T1 coil (DC/AC Inverter, Sumida / IV14080/T-LF)
Tma (Tamb)
Temperature T of winding:
R1
(Ω)
R2
(Ω)
T
(°C)
allowed
Tmax (°C)
insulation
class
Note(s):
1. All values for T (°C) are re-calculated from actual ambient respectively.
4.5.2
TABLE: ball pressure test of thermoplastic parts
allowed impression diameter (mm) .................. : ≤ 2 mm
TRF No.:IECEN60950_1B
N/A

TRF originator: SGS Fimko
Page 43 of 61
Report No.:
Part
Test temperature
(°C)
11016568 001
Impression diameter
(mm)
Note(s):
4.6.1, 4.6.2 Table: enclosure openings
P
Location
Size (mm)
Comments
Front side
11.0 x 1.5
30 openings for speakers
Left side
9.5 x 4.5
8 openings for heatsink.
Rear side
7.0 x 3.0
Kensington Lock Hole, internal plastic
enclosure as barrier.
Bottom
Max. 16.0 x 0.95
Other sides
Numerous openings.
None
--
Note(s):
4.7
Part
Table: resistance to fire
Manufacturer of material
P
Type of material
Thickness
(mm)
Flammability
class
Note(s): see appended table 1.5.1 for details.
5.1.6
Condition
TABLE: touch current measurement
L→ terminal A N → terminal A
(mA)
(mA)
N/A
Limit
(mA)
Comments
Note(s):
5.2
TABLE: electric strength tests and impulse tests
Test voltage applied between:
N/A
Test voltage (V)
Breakdown
Note(s):
5.3
TABLE: fault condition tests
P
ambient temperature (°C) ...................................... : See below

model/type of power supply ................................... : See appended table 1.5.1.

manufacturer of power supply ............................... : See appended table 1.5.1.

rated markings of power supply ............................. : See appended table 1.5.1.

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 44 of 61
No.
Component no.
Fault
Test
voltage (V)
Test
time
Fuse
no.
Report No.:
11016568 001
Fuse
Result
current (A)
For main board MS-16821
1.
CPU Fan
locked
DC 19
4.5hrs
--
--
Unit shutdown, no damaged,
no hazards, temp. was
stable, U22= 83.8°C,
ambient= 24.8°C
2.
Ventilation
openings
blocked
DC 19
7.5hrs
--
--
Unit shutdown, no damaged,
no hazards, temp. was
stable, U32= 98.6°C,
ambient= 25.8°C
3.
DT1 pin X-Z
s-c
DC 19
1min
--
--
For RTC battery, abnormal
charging current= 2.96mA.
4.
DT1 pin X-Y
s-c
DC 19
1min
--
--
For RTC battery, abnormal
charging current= 3.24mA.
5.
R104
s-c
DC 19
1min
--
--
For RTC battery, no
abnormal charging current.
For main board MS-16831
6.
CPU Fan
locked
DC 19
3hrs
--
--
Unit shutdown, no damaged,
no hazards, temp. was
stable, U13= 84.7°C,
ambient= 25.8°C
7.
Ventilation
openings
blocked
DC 19
3.5hrs
--
--
Unit shutdown, no damaged,
no hazards, temp. was
stable, U13= 79.1°C,
ambient= 24.9°C
8.
D17 pin X-Z
s-c
DC 19
1min
--
--
For RTC battery, abnormal
charging current= 2.94mA.
9.
D17 pin X-Z
s-c
DC 19
1min
--
--
For RTC battery, abnormal
charging current= 3.19mA.
10.
R173
s-c
DC 19
1min
--
--
For RTC battery, no
abnormal charging current.
Note(s):
1. In fault column: s-c=short-circuited.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 45 of 61
Report No.:
11016568 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX Australian National Differences according to CB Bulletin No. 112A, December
2006 (AS/NZS 60950.1:2003)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Annex ZZ Variations
1.2
Between the definitions for "Person, service" and
"Range, rated frequency" insert the following:
Potential ignition source
1.2.12.15
Inserted.
N/A
1.2.12.201
After the definition of 1.2.12.15, add the following: Added.
N/A
1.2.12.201 Potential ignition source:
Possible fault which can start a fire if the opencircuit voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak) a.c.
or d.c. and the product of the peak value of this
voltage and the measured r.m.s. current under
normal operating conditions exceeds 15 VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in conductive patterns on printed boards.
NOTE 201: An electronic protection circuit may be
used to prevent such a fault from becoming a
potential ignition source.
NOTE 202: This definition is from AS/NZS
60065:2003.
1.5.1
Add the following to the end of first paragraph:
Added.
N/A
Add the following to the end of first and third dash Added.
items:
N/A
"or the relevant Australian/New Zealand
Standard."
1.5.2
"or the relevant Australian/New Zealand
Standard."
2.1
Delete the Note.
Deleted.
N/A
3.2.3
Delete Note 2.
Deleted.
N/A
3.2.5
Modify Table 3B as follows:
Modified.
N/A
Rated current of
equipment A
Over 0.2 up to
and including 3
Nominal
crosssectional
2
area mm
1)
0.5
AWG or kcmil
(cross-sectional
2
area in mm )
see note 2
18 [0.8]
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 46 of 61
Report No.:
11016568 001
National Differences
Clause
Result – Remark
Requirement − Test
Over 3 up to and
including 7.5
0.75
Over 7.5 up to
and including 10
(0.75) 1.00
Over 10 up to
and including 16
(1.0) 1.5
Verdict
16 [1.3]
2)
16 [1.3]
3)
14 [2]
Replace footnote 1) with the following:
1)
This nominal cross-sectional area is only
allowed for Class II appliances if the length of the
power supply cord, measured between the point
where the cord, or cord guard, enters the
appliances, and the entry to the plug does not
exceed 2 m (0.5 mm² three-core supply flexible
cords are not permitted; see AS/NZS 3191).
Delete Note 1.
4.3.6
Replace paragraph three with:
Replaced.
N/A
Equipment with a plug portion, suitable for
insertion into a 10 A 3-pin flat-pin socket-outlet
complying with AS/NZS 3112, shall comply with
the requirements in AS/NZS 3112 for equipment
with integral pins for insertion into socket-outlets.
4.3.13.5
Add the following to the end of the first paragraph: Added.
N/A
", or AS/NZS 2211.1"
4.7
Add the following paragraph:
For alternative tests refer to clause 4.7.201.
4.7.201
Add the following after clause 4.7.3.6:
Added. The clause 4.7.201
was not tested.
N/A
Added.
N/A
4.7.201 Resistance to fire - Alternative tests
4.7.201.1
General
Equipment under test and
materials used materials and
Parts of non-metallic material shall be resistant to
components in compliance
ignition and spread of fire.
with requirements of
This requirement does not apply to decorative
IEC 60950-1.
trims, knobs and other parts unlikely to be ignited 4.7.201.1 was not considered.
or to propagate flames originating from inside the
apparatus, or the following:
(a) Components that are contained in an
enclosure having a flammability category of
FV-0 according to AS/NSZ 4695.707 and
having openings only for the connecting wires
filling the openings completely, and for the
ventilation not exceeding 1 mm in width
regardless of the length.
(b) The following parts which would contribute
negligible fuel to a fire:
-
small mechanical parts, the mass of which
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 47 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
does not exceed 4 g, such as mounting
parts, gears, cams, belts and bearings;
-
small electrical components, such as
capacitors with a volume not exceeding
3
1750 mm , integrated circuits, transistors and
optocoupler packages, if these components
are mounted on material flammability
category FV-1 or better according to AS/NZS
4695.707
NOTE - In considering how to minimize
propagation of fire and what “small parts” are,
account should be taken of the cumulative effect
of small parts adjacent to each other for the
possible effect of propagating fire from one part to
another.
Compliance is checked by tests of 4.7.201.2,
4.7.201.3, 4.7.201.4 and 4.7.201.5.
For the base materials of printed boards,
compliance is checked by the test of 4.7.201.5.
The tests shall be carried out on parts of nonmetallic material, which have been removed from
the apparatus. When the glow-wire test is carried
out, the parts shall be placed in the same
orientation, as they would be in normal use.
These tests are not carried out on internal wiring.
4.7.201.2
Parts of non-metallic material are subjected to
glow wire test of AS/NZS 4695.2.11, which is
carried out at 550 °C.
Parts for which the glow-wire test cannot be
carried out, such as those made of soft or foamy
material, shall meet the requirements specified in
ISO 9772 for category FH-3 material. The glowwire test shall be not carried out on parts of
materials classified at least FH-3 according to
ISO 9772 provided that the sample was not
thicker than the relevant part.
4.7.201.3
Testing of insulating materials
Parts of insulating materials supporting potential
ignition sources shall be subject to the glow-wire
test of AN/NZS 4695.2.11, which is carried out at
750 °C.
Equipment under test and
materials used materials and
components in compliance
with requirements of
IEC 60950-1.
4.7.201.1 was not considered.
N/A
Equipment under test and
materials used materials and
components in compliance
with requirements of
IEC 60950-1.
4.7.201.1 was not considered.
N/A
The test shall be also carried out on other parts of
insulating material which are within a distance of
3 mm of the connection.
NOTE - Contacts in components such as switch
contacts are considered to be connections.
For parts, which withstand the glow-wire test but
produce a flame, other parts above the
connection within the envelope of a vertical
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 48 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
cylinder having a diameter of 20 mm and a height
of 50 mm shall be subjected to the needle-flame
test. However, parts shielded by a barrier which
meets the needle-flame test shall not be tested.
The needle-flame test shall be made in
accordance with AS/NZS 4695.2.2 with the
following modifications:
5 Severities
Replace with:
The duration of application of the test flame shall
be 30 s ± 1 s.
8 Test procedure
8.2 Modification:
Replace the first sentence with:
The specimen shall be arranged so that the flame
can be applied to a vertical or horizontal edge as
shown in the examples of figure 1.
8.4 Modification:
The first paragraph does not apply.
Addition:
If possible, the flame shall be applied at least
10 mm from a corner.
8.5 Replacement:
The test shall be made on one specimen. If the
specimen does not withstand the test, the test
may be repeated on two further specimens, both
of which shall then withstand the test.
10 Evaluation of test results
Replace with:
The duration of burning (tb) shall not exceed 30 s.
However, for printed circuit boards, it shall not
exceed 15 s.
The needle-flame test shall not be carried out on
parts of material classified as V-0 or V-1
according to IEC 60695-11-10, provided that the
sample tested was not thicker than the relevant
part.
Australian National Differences according to CB Bulletin No. 112A, December 2006
Verdict
Page 49 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
4.7.201.4
Testing in the event of non-extinguishing material Equipment under test and
materials used materials and
If parts, other than enclosures, do not withstand
components in compliance
the glow-wire tests of 4.7.201.3, by failure to
with requirements of
extinguish within 30 s after the removal of the
IEC 60950-1.
glow-wire tip, the needle-flame test detailed in
4.7.201.1 was not considered.
4.7.201.3 is made on all parts of non-metallic
material which are within a distance of 50 mm or
which are likely to be impinged upon by flame
during the tests of 4.7.201.3. Parts shielded by a
separate barrier which meets the needle-flame
test need not to be tested.
Verdict
N/A
NOTE 1 - If the enclosure does not withstand the
glow-wire test the equipment is considered to
have failed to meet the requirement of clause
4.7.201 without the need for consequential
testing.
NOTE 2 - If other parts do not withstand the glowwire test due to ignition of the tissue paper and if
this indicates that burring or glowing particles can
fall onto an external surface underneath the
equipment, the equipment is considered to have
failed to meet the requirement of clause 4.7.201
without the need for consequential testing.
NOTE 3 - Parts likely to be impinged upon by the
flame are considered to be those within the
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting in contact with or in close proximity to
connections.
4.7.201.5
Testing of printed boards
The base material of printed boards is subjected
to needle-flame test to Clause 4.7.201.3. The
flame is applied to the edge of the board where
the heat sink effect is lowest when the board is
positioned as in normal use. The flame shall not
be applied to an edge, consisting of broken
perforations, unless the edge is less than 3 mm
for a potential ignition source.
Equipment under test and
materials used materials and
components in compliance
with requirements of
IEC 60950-1.
4.7.201.1 was not considered.
The test is not carried out if the –
- Printed board does not carry any potential
ignition source;
- Base material of printed boards, on which the
available apparent power at a connection
exceeds 15 VA operating at a voltage
exceeding 50 V and equal or less than 400 V
(peak) a.c. or d.c. under normal operating
conditions, is of flammability category FV-1 or
better according to AS/NZS 4695.707, or the
printed boards are protected by an enclosure
meeting the flammability category FV-0
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 50 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
according to AS/NZS 4695.707, or made of
metal, having openings only for connecting
wires which fill the opening completely, or
- Base material of printed boards, on which the
available apparatus power at a connection
exceeds 15 VA operating at a voltage
exceeding 400 V (peak) a.c. or d.c. under
normal operating conditions, and base material
printed boards supporting spark gaps which
provide protection against overvoltages, is of
flammability category FV-0 according to
AS/NSZ 4695.707 or the printed boards are
contained in a metal enclosure, having
openings only for connecting wires fill the
openings completely.
Compliance is determined using the smallest
thickness of the material.
NOTE - Available apparent power is the
maximum apparent power, which can be drawn
from the supplying circuit through a resistive load
whose value is chosen to maximise the apparent
power for more than 2 min when the circuit
supplied is disconnected.
6.2.2
Add the following after the first paragraph:
Added.
N/A
Deleted.
N/A
In Australia (this variation does not apply in New
Zealand), compliance with 6.2.2 is checked by the
tests of both 6.2.2.1 and 6.2.2.2.
Delete the note.
6.2.2.1
Delete Note 2.
Add the following after the first paragraph:
In Australia (this variation does not apply in New
Zealand), the electrical separation is subjected to
10 impulses of alternating polarity, using the
impulse test generator of annex N for 10/700 µs
impulses. The interval between successive
impulses is 60 s and the initial voltage, Uc, is:
- for 6.2.1 a):
7.0 kV for hand-held telephones and for
headsets and 2.5 kV for other equipment; and
- for 6.2.1b) and 6.2.1c):
1.5 kV.
NOTE 201 - The 7 kV impulse simulates lightning
surges on typical rural and semi-rural network
lines.
NOTE 202 – The 2.5 kV impulse for 6.2.1a) was
chosen to ensure adequacy of the insulation
concerned and does not necessarily simulate
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 51 of 61
Report No.:
11016568 001
National Differences
Clause
Result – Remark
Requirement − Test
Verdict
likely overvoltages.
6.2.2.2
Delete the note.
Deleted.
N/A
Add the following after the second paragraph:
In Australia (this variation does not apply in New
Zealand), the a.c. test voltage is:
- for 6.2.1a):
3 kV; and
- for 6.2.1b) and 6.2.1c):
1.5 kV.
NOTE 201 – Where there are capacitors across
the insulation under test, it is recommended that
d.c. test voltages are used.
NOTE 202 – The 3 kV and 1.5 kV values have
been determined considering the low frequency
induced voltages from the power supply
distribution system.
Annex P
Add the following Normative References to Annex Added.
P:
IEC 60065, Audio, Video and similar electronic
apparatus - Safety requirements
AS/NZS 3112, Approval and test specification Plugs and socket-outlets
AS/NZS 3191, Approval and test specification Electric flexible cords
AS/NZS 4695.707, Fire hazard testing of
electrotechnical products - Methods of test for the
determination of the flammability of solid electrical
insulating materials when exposed to an igniting
source
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 52 of 61
Report No.:
11016568 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX Canadian National Differences according to CB Bulletin No. 112A, December
2006 (CAN/CSA C22.2 No. 60950-1/UL60950-1)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Special National Conditions
1.1.1
All equipment is to be designed to allow
installations in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70,the
Canadian Electrical Code (CEC), Part I,
CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2. Also,
unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
Equipment was evaluated
according to IEC 60950-1. The
requirement have to be
checking to national approval.
N/A
1.4.14
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
Class III equipment.
N/A
1.5.5
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type (e.g. DP, CL2) specified in the NEC.
No supply cords provided.
N/A
Class III equipment.
N/A
Where a fuse is used to provide Class 2, Limited No such fuse used.
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
N/A
For lengths 3.05 m or less, external
interconnecting flexible cord and cable
assemblies that are not types specified in the
NEC are required to have special construction
features and identification markings.
1.7.1
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
A voltage rating that exceeds an attachment plug
cap rating is only permitted if it does not exceed
the extreme operating conditions in Table 2 of
CAN/CSA C22.2 No. 235, and if it is part of a
range that extends into the Table 2 “Normal
Operating Conditions.” Likewise, a voltage rating
shall not be lower than the specified “Normal
Operating Conditions,” unless it is part of a range
that extends into the “Normal Operating
Conditions.”
2.5
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Page 53 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
2.7.1
Suitable NEC/CEC branch circuit protection rated No such outlet provided.
at the maximum circuit rating is required for all
standard supply outlets, receptacles and mediumbase or smaller lampholders if the supply branch
circuit protection is not suitable.
Verdict
N/A
Power distribution transformers distributing power
at 100 volts or more, and rated 10 kVA or more,
require transformer overcurrent protection.
3.2
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC/CEC.
Class III equipment.
N/A
3.2.1
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
No such cords provided.
N/A
3.2.3
Permanent connection of equipment to the mains Not permanent connection
supply by a power supply cord is not permitted,
equipment.
except for certain equipment, such as ATMs.
N/A
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length.
No such cords provided.
N/A
Not permanent connection
equipment.
N/A
Flexible power supply cords are required to be
compatible with Article 400 of the NEC, and
Tables 11 and 12 of the CEC.
3.2.9
Permanently connected equipment is required to
have a suitable wiring compartment and wire
bending space.
3.3
Wiring terminals and associated spacings for field No such terminal used.
wiring connections shall comply with CSA C22.2
No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm²).
No such terminal used.
N/A
3.3.4
Terminals for permanent wiring, including
No such terminal used.
protective earthing terminals, are required to be
suitable for U.S./Canadian wire gauge sizes, rated
125 percent of the equipment rating, and be
specially marked when specified (1.7.7).
N/A
3.4.2
Motor control devices are required for cordNo motor used.
connected equipment with a motor if the
equipment is rated more than 12A, or if the motor
has a nominal voltage rating greater than 120V,
or is rated more than 1/3 hp (locked rotor current
over 43 A)
N/A
3.4.8
Vertically-mounted disconnect switches and
No such switches used.
circuit breakers are required to have the ”on”
position indicated by the handle in the up position.
N/A
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Page 54 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
Not for computer room used.
4.3.12
The maximum quantify of flammable liquid stored No flammable liquid used.
in equipment is required to comply with NFPA 30.
N/A
4.3.13
Equipment with lasers is required to meet Code of No lasers.
Federal Regulations 21 CFR 1040 (and the
Canadian Radiation Emitting Devices Act, REDR
C1370).
N/A
4.7
For computer room applications, automated
Not for computer room used.
information storage systems with combustible
media greater than 27 cubic feet are required to
have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
N/A
4.7.3.1
For computer room applications, enclosures with Not for computer room used.
combustible material measuring greater than 0.9
m² or a single dimension greater than 1.8 m are
required to have a flame spread rating of 50 or
less. For other applications, enclosures with the
same dimensions require a flame spread rating of
200 or less.
N/A
Annex H
Equipment that produces ionizing radiation is
required to comply with the Code of Federal
Regulations, 21 CFR 1020 (and the Canadian
Radiation Emitting Devices Act, REDR C1370).
N/A
No ionizing radiation.
Verdict
N/A
Other differences
1.5.1
Components of equipment must be suitable for
the application, and must comply with the
requirements of the equipment standard and the
applicable national (Canadian and/or U.S.)
component or material standards, as far as they
may apply.
Components are UL or CSA
approved, see component list
1.5.1.
The acceptance will be based on the following:
A) A component Certified by a Canadian or U.S.
National Certification Body (NCB) to a
Canadian or U.S. component standard will be
checked for correct application and use in
accordance with its specified rating. Where
necessary, it will also be subject to the
applicable tests of the equipment standard.
B) A component, which has a CB Test
Certificate for compliance with a relevant IEC
component standard, will be checked for
correct application and use in accordance
with its specified ratings. Where necessary, it
will also be subject to the applicable tests of
the equipment standard, and to the applicable
Canadian National Differences according to CB Bulletin No. 112A, December 2006
P
Page 55 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
tests of the Canadian and/or U.S. component
or material standard, under the conditions
occurring in the equipment.
C) A component, which has no approval as in A)
or B) above or which is used not in
accordance with its specified ratings, will be
subject to the applicable tests of the
equipment standard, and to the applicable
tests of the Canadian and/or U.S. component
or material standard, under the conditions
occurring in the equipment.
D) Some components may require annual retesting, which may be carried out by the
manufacturer, CSA International or another
laboratory
2.3.1
For TNV-2 and TNV-3 circuits with other than
No TNV circuits.
ringing signals and with voltages exceeding
42.4 Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mAd.c.
under normal operating conditions.
N/A
2.3.2
In the event of a single fault, the limits of 2.2.3
No TNV circuits.
apply to SELV Circuits and accessible conductive
parts.
N/A
2.6.3.3
When subject to impedance testing, protective
Class III equipment.
earthing and bonding are required to be subjected
to the additional test conditions specified.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power Not connected to DC mains.
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, writing, marking and
installation instruction requirements.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of No CRT used.
160mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
N/A
4.3.2
Equipment with handles is required to comply with No such handles used.
special loading tests.
N/A
5.1.8.3
Equipment intended to receive telecommunication No TNV circuit.
ringing signals is required to comply with a special
touch current measurement tests.
N/A
6.2.1
Enamel coating on winding wire not considered
electrical separation unless subjected to special
investigation.
N/A
No TNV circuit.
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Page 56 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
6.4
Equipment intended for connection to
No TNV circuit.
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
N/A
6.5
Equipment connected to a telecommunications
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
No TNV circuit.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
No TNV circuit.
N/A
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Verdict
Page 57 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
APPENDIX Korean National Differences according to CB Bulletin No. 112A, December 2006
(K60950)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
1.5.101
Addition:
Class III equipment.
N/A
To be evaluated when
submitted for national
approval.
N/A
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305).
7
Addition: EMC
The apparatus shall comply with the relevant
CISPR standards.
Korean National Differences according to CB Bulletin No. 112A, December 2006
Page 58 of 61
Report No.:
11016568 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX US National Differences according to CB Bulletin No. 112A, December 2006
(UL 60950-1)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Special National Conditions
1.1.1
All equipment is to be designed to allow
installations in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70,the
Canadian Electrical Code (CEC), Part I,
CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2. Also,
unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
Equipment in compliance with
IEC 60950-1. Overall
acceptance has to be
evaluated during the national
approval process.
N/A
1.4.14
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
Class III equipment.
N/A
1.5.5
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type (e.g. DP, CL2) specified in the NEC.
No supply cord provided.
N/A
Class III equipment.
N/A
Where a fuse is used to provide Class 2, Limited No such fuse used.
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
N/A
For lengths 3.05 m or less, external
interconnecting flexible cord and cable
assemblies that are not types specified in the
NEC are required to have special construction
features and identification markings.
1.7.1
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
A voltage rating that exceeds an attachment plug
cap rating is only permitted if it does not exceed
the extreme operating conditions in Table 2 of
CAN/CSA C22.2 No. 235, and if it is part of a
range that extends into the Table 2 “Normal
Operating Conditions.” Likewise, a voltage rating
shall not be lower than the specified “Normal
Operating Conditions,” unless it is part of a range
that extends into the “Normal Operating
Conditions.”
2.5
2.7.1
Suitable NEC/CEC branch circuit protection rated No such outlets provided.
at the maximum circuit rating is required for all
standard supply outlets, receptacles and mediumbase or smaller lampholders if the supply branch
US National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 59 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
circuit protection is not suitable.
Power distribution transformers distributing power
at 100 volts or more, and rated 10 kVA or more,
require transformer overcurrent protection.
3.2
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC/CEC.
Class III equipment.
N/A
3.2.1
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
No such cords provided for
this country.
N/A
3.2.3
Permanent connection of equipment to the mains Not permanent connection
supply by a power supply cord is not permitted,
equipment.
except for certain equipment, such as ATMs.
N/A
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length.
No such cords provided for
this country.
N/A
Not permanent connection
equipment.
N/A
Flexible power supply cords are required to be
compatible with Article 400 of the NEC, and
Tables 11 and 12 of the CEC.
3.2.9
Permanently connected equipment is required to
have a suitable wiring compartment and wire
bending space.
3.3
Wiring terminals and associated spacings for field No such terminal used.
wiring connections shall comply with CSA C22.2
No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm²).
No such terminal used.
N/A
3.3.4
Terminals for permanent wiring, including
No such terminal used.
protective earthing terminals, are required to be
suitable for U.S./Canadian wire gauge sizes, rated
125 percent of the equipment rating, and be
specially marked when specified (1.7.7).
N/A
3.4.2
Motor control devices are required for cordNo motor used.
connected equipment with a motor if the
equipment is rated more than 12A, or if the motor
has a nominal voltage rating greater than 120V,
or is rated more than 1/3 hp (locked rotor current
over 43 A)
N/A
3.4.8
Vertically-mounted disconnect switches and
No such switches used.
circuit breakers are required to have the ”on”
position indicated by the handle in the up position.
N/A
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
4.3.12
The maximum quantify of flammable liquid stored No flammable liquid used.
in equipment is required to comply with NFPA 30.
Not for computer room.
US National Differences according to CB Bulletin No. 112A, December 2006
N/A
N/A
Page 60 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
4.3.13
Equipment with lasers is required to meet Code of No lasers.
Federal Regulations 21 CFR 1040 (and the
Canadian Radiation Emitting Devices Act, REDR
C1370).
N/A
4.7
For computer room applications, automated
Not for computer room.
information storage systems with combustible
media greater than 27 cubic feet are required to
have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
N/A
4.7.3.1
For computer room applications, enclosures with Not for computer room.
combustible material measuring greater than 0.9
m² or a single dimension greater than 1.8 m are
required to have a flame spread rating of 50 or
less. For other applications, enclosures with the
same dimensions require a flame spread rating of
200 or less.
N/A
Annex H
Equipment that produces ionizing radiation is
required to comply with the Code of Federal
Regulations, 21 CFR 1020 (and the Canadian
Radiation Emitting Devices Act, REDR C1370).
N/A
No ionizing radiation.
Verdict
Other differences
1.5.1
Some components and materials associated with
the risk of fire, electric shock, or personal injury
are required to have component or material
ratings in accordance with the applicable national
(U.S. and Canadian) component or material
requirements. These components include:
Components are UL or CSA
approved, see component list
1.5.1.
attachment plugs, battery packs (rechargeable
type, used with transportable equipment), cathode
ray tubes, circuit breakers, communication circuit
accessories, connectors (used for current
interruption of non-LPS circuits), cord sets and
power supply cords, direct plug-in equipment,
enclosures (outdoor), flexible cords and cables,
fuses (branch circuit), fuseholders, ground-fault
current interrupters, industrial control equipment,
insulating tape, interconnecting cables,
lampholders, limit controls, printed wiring,
protectors for communications circuits,
receptacles, solid state controls, supplementary
protectors, surge suppressors, switches
(including interlock switches), thermal cut-offs,
thermostats, multi-layer transformer winding wire,
tubing, wire connectors, and wire and cables.
US National Differences according to CB Bulletin No. 112A, December 2006
P
Page 61 of 61
Report No.:
11016568 001
National Differences
Clause
Requirement − Test
Result – Remark
2.3.1
For TNV-2 and TNV-3 circuits with other than
No TNV circuits.
ringing signals and with voltages exceeding
42.4 Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA d.c.
under normal operating conditions.
N/A
2.3.2
In the event of a single fault, the limits of 2.2.3
No TNV circuits.
apply to SELV Circuits and accessible conductive
parts.
N/A
2.6.3.3
When subject to impedance testing, protective
Class III equipment.
earthing and bonding are required to be subjected
to the additional test conditions specified.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power Not connected to DC mains.
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, writing, marking and
installation instruction requirements.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of No CRT used.
160mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
N/A
4.3.2
Equipment with handles is required to comply with No such handles used.
special loading tests.
N/A
5.1.8.3
Equipment intended to receive telecommunication No TNV circuit.
ringing signals is required to comply with a special
touch current measurement tests.
N/A
6.2.1
Enamel coating on winding wire not considered
electrical separation unless subjected to special
investigation.
No TNV circuit.
N/A
6.4
Equipment intended for connection to
No TNV circuit.
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
N/A
6.5
Equipment connected to a telecommunications
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
No TNV circuit.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
No TNV circuit.
N/A
US National Differences according to CB Bulletin No. 112A, December 2006
Verdict
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement