Bosch EX27N Installation instructions

Add to my manuals
48 Pages

advertisement

Bosch EX27N Installation instructions | Manualzz

INSTALLATION INSTRUCTIONS

EX27/EX27N/EX27D

All-Weather Cameras

MAN-27/27N/27D-01

1

IMPORTANT SAFETY INSTRUCTIONS

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

2

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

3

IMPORTANT

For best results, please read this Instruction Booklet prior to installing the EX27 camera.

EU Directives covered by this declaration:

72/9/EC Low Voltage Directives

89/336/EEC Electromagnetic Compatibility Directive

This installation should be made by a qualified service person and conform to all local codes.

Bosch Security Systems will not be responsible for injuries or damages resulting from the improper installation or use of any camera sold by Bosch Security Systems, their agents, distributors or dealers.

4

NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. As part of its’ normal operation this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may cause interference to radio communications.

However, there is no guarantee that interference will not occur on a particular installation. If the device does cause interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures:

1) Fit Ferrite beads on all cable to and from the power

supply box, within the box walls.

2) Route the composite cable between the camera and the power supply in steel conduit piping over the entire run of the cable up to and including connection to a deep conduit base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box.

3) Contact a Bosch Service Center for further advice.

5

INDEX – EX27/27N/EX27D

1.

DESCRIPTION....................................................... 7

2.

UNPACKING .......................................................... 8

3.

EX27/EX27N MECHANICAL SPECIFICATIONS ... 9

4.

EX27D MECHANICAL SPECIFICATIONS........... 10

5.

INITIAL PREPARATIONS .................................... 11

6.

GUIDELINES........................................................ 12

7.

VOLTAGE INPUT................................................. 13

8.

CAMERA AND LENS ACCESS ........................... 14

9.

PHOTOCELL ADJUSTMENTS ............................ 17

10.

LENS ADJUSTMENTS......................................... 19

11.

OSD MENU SYSTEM .......................................... 21

12.

TROUBLESHOOTING GUIDE ............................. 40

13.

GENERAL SPECIFICATIONS ............................. 43

6

1. DESCRIPTION

The EX27 camera is an all-weather system that includes all of the best features of a “plug and play” camera without compromise to CCD optics and lens quality.

Full size vari-focal auto-iris lenses are integrated as standard equipment for simplified installations. High resolution extended day/night

CCDs ensure that a picture is received under extreme outdoor lighting conditions.

The EX27 is rugged, compact, power protected, weather sealed, easily installed and designed for use in industrial applications.

A voltage regulator circuit automatically allows for 12VDC or 24VAC operation without any wiring changes. Its wider voltage range also provides protection from voltage surge, transient spikes, and reverse voltage.

The EX27 is available in several models to meet individual requirements or specific needs.

7

2. UNPACKING

Care should be taken when unpacking. Check the parts list and confirm all items have been located.

Inspect the equipment thoroughly to ensure nothing was damaged in transit.

Contact a Bosch Service Center if a problem is noted, see the rear page of this booklet for contact numbers.

PARTS LIST (items supplied with unit)

- EX27/EX27N/EX27D camera assembly

- Installation Instructions

- Universal type pan/tilt mounting bracket with

¼ - 20 captive nut

-3mm Allen key

ITEMS REQUIRED FOR INSTALLATION

(not supplied with unit)

- Hardware for camera mounting (bolts, etc.)

- Mounting tools and wrenches

- Optional mounting brackets (contact

Bosch for details and prices)

8

3. EX27/EX27N MECHANICAL

SPECIFICATIONS

9

4. EX27D MECHANICAL SPECIFICATIONS

10

5. INITIAL PREPARATIONS

 Determine the operating voltage at the installation site.

 All cameras have been tested prior to shipment.

Select a suitable location that is protected from accidental damage, tampering, and environmental conditions exceeding the camera’s specifications.

Caution: The selected mounting location should not place the camera in a situation where its environmental specifications could be exceeded.

Ensure the selected location is protected from falling objects, accidental contact with moving objects, and unintentional interference from personnel. Follow all applicable building codes.

11

6. GUIDELINES

The following installation guidelines must be followed:

 Locate the camera such that it cannot be easily interfered with, either intentionally or accidentally.

 Select a mounting surface capable of supporting the combined weight of the camera and mounting hardware under all expected conditions of vibration and temperature.

 Secure all cabling.

 Installations on drywall must use a ¼” bolt and drywall butterfly type anchor or superior connection.

12

7. VOLTAGE INPUT

The camera unit is pre-connected with an electrically isolated power board for 24VAC or

12VDC operation with no wiring change or wiring polarity. See figure 7-1 for wiring details.

Note: Input voltage is 10.5VDC to 40VDC for DC input. The AC input range is 12VAC to 28VAC.

Power

IN

from supply

Power

OUT

to camera

FIGURE 7 – 1

12VDC or 24VAC

Electrically Isolated Board

13

8. CAMERA AND LENS ACCESS

The following steps show the installer how to access the camera board and the camera lens.

Step 2.1 - Remove the four cap screws with a

3mm Allen key. See Figure 8-1 on page 15.

Step 2.2 - Carefully slide out the rear housing from the main enclosure. Make sure the gasket remains with the rear section. See Figure 8-2 on page 16.

Step 2.3 - Make any necessary camera or lens adjustments as described in

Section 9, 10 or 11.

Step 2.4 - Carefully slide the rear section into the main enclosure and tighten the cap screws.

14

Cap screw

FIGURE 8 – 1

Rear Housing Removal

15

FIGURE 8 – 2

Camera and Lens Access

16

9. PHOTOCELL ADJUSTMENTS

The photocell settings are optimally set from the factory; only adjust these settings if experiencing undesired day/night switching operation. To increase the night switching sensitivity turn the dial clockwise, to increase the day switching sensitivity turn the dial counter-clockwise. For

EX27N versions refer to figure 9-1. For EX27 and

EX27D refer to figure 9-2.

Power to

LED Array Photocell

Adjustment

12V

Enable

Power

Input

FIGURE 9 – 1

EX27N LED Array Power Board

17

Photocell Adjustment

FIGURE 9 – 2

EX27/EX27D Day/Night Switch

Adjustment

18

10. LENS ADJUSTMENTS

Refer to figure 10-1 and follow the directions below:

 Loosen the lens set screws for focus/zoom adjustments.

 The adjustment marked T ←→ W is for image zoom.

 The adjustment marked N ←→ ∞ is for image focus.

 Re-tighten the setscrews after focus adjustments have been completed.

FIGURE 10 – 1

EX27 Vari-focal Lens Focus Adjustment

19

Use a Neutral Density filter or an Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For varifocal lenses, the camera should be focused with the lens iris fully opened to simulate the worst possible depth of field. Using a Neutral Density filter or Infra-Red Pass filter will ensure the iris is fully open for correct setup and adjustment.

Note that statement above is applicable only for Day/Night or IR version cameras.

20

11. OSD MENU SYSTEM

1. Follow the instructions in Section 8 to access the OSD controls.

2. Enter the OSD menu by pressing the joystick button; to navigate through the menu use up, down, left and right. the camera adjustments.

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

12. TROUBLESHOOTING GUIDE

PROBLEM

No Video

POSSIBLE

CAUSE

1. Power Supply:

-Connections….

-Voltage Range...

LIKELY

SOLUTION

Check input power connections at the cable leads.

Check for loose wires.

If connected to DC, check voltage input range of 10.5 - 40 V.

If connected to AC, check input voltage range of 12 – 28 V.

Measure the voltage at the Input terminal block.

40

No Video

(cont’d.)

__________

Poor

Picture

Quality

Snowy

Image

2. Video

Connections

________________

Poor Video Signal

41

Determine if wiring polarity at “Video

Connector” terminal block is correct.

Check BNC connector.

If still no video, connect the camera directly to the monitor. Check the video signal. If okay, the problem is with the interconnections.

If still no video, contact a Bosch

Service Center.

See rear page of this manual for contact information.

_________________

Ensure video cable is correctly matched and terminated with

75 ohms at each end.

Make sure video cables are similar types.

Poor

Picture

Quality

Snowy

Image

(cont’d.)

Horizontal

Scan Lines,

Rolling Up or Down

Negative, scrambled, or faded image

Noisy Power

Supply

Ground Looping on video cable

24V ac operation

Low voltage

Check connections.

Relocate or replace power supply.

Check the coax cable shield is not touching ground, e.g. at couplings.

An electrically isolated circuit board or isolation transformer may be required.

Line Lock adjustment required.

Check voltage at input power cable.

Must be >10.5V dc or

>12V ac.

42

13. GENERAL SPECIFICATIONS

Input Voltage: 10.5-40 VDC

VAC

4.5W

Enclosure (housing): Aluminum casting and

IP66 / NEMA4)

Viewing Window:

Weight:

Polycarbonate

1.4kg ( 3.1lbs. )

Subject to Change Without Notice.

43

Notes:

44

Notes:

45

Notes:

46

Notes:

47

Americas

Bosch Security Systems, Inc.

850 Greenfield Road

Lancaster, Pennsylvania 17601 USA

Telephone: + 1 888-289-0096

Fax: + 1 585-223-9180 [email protected] www.boschsecurity.us

Europe, Middle East, Africa

Bosch Security Systems B.V.

P.O. Box 80002

5600 JB Eindhoven, Netherlands

Phone: + 31 40 2577 284

Fax: + 31 40 2577 330 [email protected] www.boschsecurity.com

Asia Pacific

Bosch Security Systems Pte Ltd.

11 Bishan Street 21, Singapore, 573943

Phone: +65 6319 3450

Fax: +65 6319 3499 [email protected] www.boschsecurity.com

© Bosch Security Systems Inc. 2010; Data subject

to change with out notice

48

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals