Free-Air® Pumps Instruction Manual

Free-Air® Pumps Instruction Manual
Free-Air® Pumps
Instruction Manual
EDP10
EDP16TE
This Manual provides
detailed instructions,
warnings and other
information for
individuals
using Bullard FreeAir Pump models
EDP10, EDP16TE and
EDP16HAZA
EDP16HAZ
TABLE OF CONTENTS
GENERAL INFORMATION . ......................................................................................................... 1
WARNINGS ............................................................................................................................ 2, 3
BREATHING AIR REQUIREMENTS ............................................................................................. 4
ASSEMBLING THE FREE-AIR PUMP
Model EDP10 . ............................................................................................................
Model EDP16TE . ........................................................................................................
Model EDP16HAZ . .....................................................................................................
Pump Performance Specifications ............................................................................
Electric Motor Specifications . ...................................................................................
5
5
5
6
7
OPERATING THE FREE-AIR ® PUMP . .......................................................................... 8, 9, 10, 11
MAINTAINING THE FREE-AIR PUMP ...................................................................................... 12
FREE-AIR PUMP TROUBLE SHOOTING GUIDE ................................................................... 13, 14
REPLACEMENT PARTS ............................................................................................................. 15
PUMP WARRANTY ................................................................................................................... 17
AIR FILTER REPLACEMENT SCHEDULE ................................................................................... 18
Free-Air® Pumps
Instruction Manual
GENERAL INFORMATION
Bullard Free-Air ® pumps transfer ambient air from a clean air location, where breathable
air can be assured at all times, to workers wearing Type C or CE continuous- flow supplied-air
respirator hoods or tight fitting half or full face masks.
The ambient air is filtered through a medium efficiency inlet air filter and a Carbofine outlet
filter before entering the respirator’s air supply hose.
Bullard Free-Air pumps are oil-less and have rotary carbon vanes. They produce no carbon
monoxide, oil vapors, oil mist or moisture. They do not require expensive carbon monoxide
monitors, high temperature alarms or airline filters. No calibration is required.
The pumps will supply air to one, two or three workers depending on the pump model and
style of respirator(s) being used. The chart below describes the pump model, the number of
respirators each unit will supply and its maximum outlet pressure.
PUMP SPECIFICATION TABLE
Maximum
Number of Respirators
Pump Model No.
Hood Style
Full or Half-Mask
Maximum Outlet
Air Pressure*
EDP10
One
Two
15 psig (103 kPa)**
EDP16TE
Two
Three
15 psig (103 kPa)
EDP16HAZ
Two
Three
15 psig (103 kPa)
* USE ONLY SUPPLIED-AIR RESPIRATORS THAT ARE APPROVED BY MSHA/NIOSH TO
OPERATE AT LESS THAN 15 PSIG (103 kPa).
**To convert kPa to bar, divide kPa by 100
1
� WARNING
READ ALL INSTRUCTIONS IN THIS MANUAL BEFORE USING FREE AIR® PUMP MODELS EDP10, EDP-16-TE OR EDP-16-HAZ.
FAILURE TO OPERATE ANY OF THESE PUMPS IN ACCORDANCE WITH THE INSTRUCTIONS
CONTAINED IN THIS MANUAL MAY RESULT IN DEATH OR SERIOUS INJURY TO THE
RESPIRATOR WEARER.
1. Locate the pump’s inlet air filter in a clean breathable air location at all times. The pump
DOES NOT remove toxic gases or other contaminants from the incoming air
it transfers to the respirator wearer.
See the BREATHING AIR REQUIREMENTS section on page 4 for specific details on breathing air quality. THESE PUMPS DO NOT SUPPLY OXYGEN.
2. This pump will only supply the required volume of air [6-15 cfm (170-425 lpm) for hoods or
4-15 cfm (113-425 lpm) for tight fitting half or full face masks] to low pressure continuous-flow supplied-air respirators approved by MSHA/NIOSH to operate at less than 15
psig (103 kPa).
Be sure that the pump’s outlet pressure, measured by the pressure gauge on the pump, is
maintained above the minimum pressure setting required by the respirator manufacturer.
To be assured your respirator can be used with this pump refer to:
a) The Pump Specification Table on page 1 for the maximum outlet pressure of the pump
model you are using.
b) The section in the respirator’s instruction manual for the respirator’s approved pressure range and permissible air supply hose lengths.
If you have any questions about whether or not your respirator is compatible with
this pump, contact Bullard Customer Service Department at 1-800-827-0423 or
1-859-234-6611.
3. Supplied-air respirators used with this pump must not be worn in any atmosphere immediately dangerous to life or health or from which the wearer cannot escape without the use
of the respirator.
2
Free-Air® Pumps
Instruction Manual
4. When connecting your respirator to the Free-Air® pump use only the air supply hose and
couplers required by the respirator manufacturer and approved by MSHA/NIOSH.
Use of non-approved hose or couplers will void the respirator’s MSHA/NIOSH Approval
and could reduce the air flow to the respirator, resulting in possible death or serious
injury to the respirator wearer.
5. DO NOT modify or alter this pump in any manner. Use only approved Bullard Free-Air pump
components and replacement parts on the pump.
Failure to use approved Bullard components and replacement parts invalidates all Bullard
warranties, and may result in death or serious injury to the respirator wearer.
6. If you have any questions concerning the use of this pump or your respirator, or you are
not sure the inlet filter is in a breathable location, ask your supervisor.
All instructions for the use and care of this product must be supplied to you by your employer as recommended by the manufacturer and as required by Federal Law
(29 CFR 1910.134).
For technical assistance or additional copies of this manual, call Bullard Customer Service or
go to www.Bullard.com to download a copy.
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
1-800-827-0423
859-234-6611
www.bullard.com
3
Air Quality
The Free-Air® pump’s inlet filter must be
located in a clean breathable air location at
all times.
The breathable air drawn into the inlet
filter must meet at least the requirements
for Type 1 gaseous air described in the
Compressed Gas Association Commodity
Specifications G-7.1 (Grade D or higher), as
specified by Federal Law 42CFR, Part 84,
Subpart b, and 29CFR1910.134(i).
4
The requirements of Grade D breathable air
include:
*Oxygen.................................... 19.5 - 23.0 %
*Hydrocarbons (condensed)
in mg/m3 of gas.............5 mg/m3 maximum
*Carbon Monoxide.............10 ppm maximum
*Carbon Dioxide...........1,000 ppm maximum
*No toxic contaminants at levels which
would make the air unsafe to breathe.
Refer to the C.G.A. Commodity Specification
G-7.1 for complete details. It is available
from: Compressed Gas Association, 500 Fifth
Ave., New York, NY 10036.
Free-Air® Pumps
Instruction Manual
Assembling the
Free-Air® Pump
1. MODEL EDP10:
a. Open the shipping carton and remove
the top layer of foam from the box.
Remove the pump from the carton.
We recommend storing the shipping
carton and foam in the event the pump
must be shipped in the future.
Figure 1
b. Remove the pressure gauge from its
separate box. Assemble it to the gauge
port located on top of the pump’s outlet
filter body. The gauge should face
outward so that it can be read while
setting the pressure adjustment knob
(see Figure 1).
There is no other assembly required on
the EDP10 pump.
2. MODEL EDP16TE OR EDP16HAZ:
a. Remove the pump from the shipping
carton. We recommend storing the
shipping carton and plywood board in
the event the pump must be shipped in
the future.
b. Remove the pressure gauge from its
separate box. Assemble it to the gauge
port located on top of the pump’s outlet
filter body. The gauge should face
outward so that it can be read while
setting the pressure adjustment knob
(see Figure 1).
3. ALL PUMPS:
a. Unscrew the pump’s outlet filter jar
and check to be sure the outlet filter
cartridge is seated firmly into the outlet
Figure 2
filter body (see Figure 2).
DO NOT OPERATE THIS PUMP
WITHOUT AN OUTLET FILTER
CARTRIDGE (Cat. No. S17101).
Be sure the outlet filter O-ring is installed inside the filter body.
b. Screw the filter jar back onto the filter
body. Tighten firmly by hand, making
sure the jar is seated against the
O-ring so that no air can escape.
c. Check to be sure that the inlet filter,
pressure gauge and outlet couplings
are all assembled tightly to the pump
so that no air can escape.
5
PUMP PERFORMANCE SPECIFICATIONS
EDP10 EDP16TE EDP16HAZ
PUMP DESIGN:
Rotary Carbon
Vane (4 vanes)
Rotary Carbon
Vane (4 vanes)
Rotary Carbon
Vane (4 vanes)
MAXIMUM
PRESSURE:
15 psig
(103 kPa)
15 psig
(103 kPa)
15 psig
(103 kPa)
TOTAL AIR
FLOW:
kPa)
10 cfm @ 5 psig
(283 lpm @ 34 kPa)
16 cfm @ 5 psig
(453 lpm @ 34 kPa)
16 cfm @ 5 psig
(453 lpm @ 34
INLET
FILTER:
Medium
Efficiency
Medium
Efficiency
Medium
Efficiency
OUTLET
FILTER:
Carbofine
with activated
carbon
Carbofine
with activated
carbon
Carbofine
with activated
carbon
DIMENSIONS:
Width
Length
Height
8 inches (20.3 cm)
16.3 inches (41.4 cm)
13.5 Inches (34.3 cm)
14 inches (35.5 cm) 28 inches (71.1 cm)
16 inches (40.6 cm)
14 inches (35.5 cm)
28 inches (71.1 cm)
16 inches (40.6 cm)
WEIGHT:
49 lbs. (approx.)
(22.2 kg)
98 lbs. (approx.)
(44.5 kg)
98 lbs. (approx.)
(44.5 kg)
6
Free-Air® Pumps
Instruction Manual
Electric Motor Specifications:
EDP10 EDP16TE EDP16HAZ
ENCLOSURE:
Open, Drip-
Totally-Enclosed,
proof Fan Cooled
Capacitor Start
Meets UL
Requirements,
Meets UL Requirements,
CSA Approved
CSA Approved
Hazardous Duty
CLASS:
Natl. Elec. Code:
Natl. Elec. Code:
Class B
Class III Design N
Division 1 and 2
Code K
National Electric Code:
Class I, Group D, Div. 1 & 2
Class II, Group F, Div. 1 & 2
Class III, Division 1 & 2
H.P.
3/4
1 1/2
1 1/2
PHASE:
Single
Single
Three
CYCLES:
60 Hz
60 Hz
60 Hz
VOLTS:
115
115/208/230
(Connected
for 115 V.)
230 - 460
AMPS:
10.2 @ 115 V.
17.2 @ 115 V.
8.8 @ 208/230 V.
5.0 @ 230 V.
2.5 @ 460 V.
SERVICE
FACTOR:
1.15
1.0
PROTECTOR:
Internal Thermal
Overload
Manual Reset Thermal
Overload equipped for
115 volt operation.
Thermal Overload and
Starter/Contactor to be
provided by the user.
Thermal Overload and
Starter/Contactor to be
provided by the user if
rewired to 208/230 volts.
1.25
Meets UL Requirements,
CSA Approved
� WARNING
PROPER MOTOR SELECTION AND WIRING (IN ACCORDANCE WITH LOCAL AND NATIONAL ELECTRIC CODES) IS
THE RESPONSIBILITY OF THE USER.
7
Operating the Free-Air Pump
� WARNING
THE RESPIRATOR USER MUST NOT ENTER THE CONTAMINATED WORK AREA UNTIL ALL OF
THE FOLLOWING STEPS HAVE BEEN COMPLETED
1. Analyze the atmosphere at the location of
the air inlet and the pump itself to be sure
the pump will not be operating in a contaminated or an explosive atmosphere.
2. If Using an EDP10 Pump:
Plug the pump into a 115 volt electrical
outlet. The pump’s motor is equipped with a
toggle switch and a 7 foot (2 m) ground-ed
cord with a standard three-prong plug.
You may use up to 100 (30.5 m) feet of 50
amp, 3-wire grounded extension cord to
reach your electrical outlet. We recommend using 14 gauge wire. Avoid excess-ive
lengths of extension cord, especially if running the pump continuously.
If Using an EDP16TE Pump:
Plug the pump into a 115 volt electrical
outlet. The pump’s motor is equipped with a
toggle switch and a 7 (2 m) foot ground-ed
cord with a standard three-prong plug.
You may use up to 100 (30.5 m) feet of 50
amp, 3-wire grounded extension cord to
reach your electrical outlet. We recommend
using 12 gauge wire.
Avoid excessive lengths of extension cord,
especially if running the pump continuously.
The pump’s motor is equipped with manual
reset thermal overload protection for 115
volt operation. The reset button is located
on the side opposite the toggle switch.
The EDP16TE may be rewired for 208/230
volt, 60 Hz operation. If rewired to 208/230
a suitable starter/contactor and thermal
overload protector must be provided by
the user. The conversion work should be
performed by a qualified electrician.
If Using an EDP16HAZ Pump:
The EDP16HAZ must be wired for either 230
or 460 volt, 3-phase, 60 Hz operation.
THE USER MUST SUPPLY AN EXPLOSIONPROOF THERMAL OVERLOAD PROTECTOR
AND A STARTER/CONTACTOR SWITCH.
Proper wiring should be performed by a
qualified electrician.
REFER TO THE MOTOR NAME PLATE OR
JUNCTION BOX COVER FOR PROPER
WIRING DIAGRAM.
� WARNING
PROPER MOTOR SELECTION AND WIRING (IN ACCORDANCE WITH LOCAL AND NATIONAL
ELECTRIC CODES) IS THE RESPONSIBILITY OF THE USER.
8
Free-Air® Pumps
Instruction Manual
3. Each pump will operate sitting on its four
rubber mounts. It does not need to be bolted
down. If desired, the pump may be mounted
on a wall or ceiling as long as the shaft
center line is horizontal.
4. Make sure the pump’s inlet filter is located in a clean, uncontaminated location where
breathable air is assured at all times (see
Figure 3).
If the inlet filter cannot be placed in a clean
breathable location, install Bullard’s 50 foot
(15 m) Inlet Extension Hose Kit (Cat. No.
V50IN) to the pump’s inlet port. See the
directions shipped with the Extension Hose
Kit for assembly instructions.
If clean breathable air cannot be guaranteed
at all times within this 50 foot (15 m) reach,
you may add up to five (5) additional lengths of
50 foot (15 m) Extension Hose (Cat. V50EX).
Therefore, you may place your inlet filter up
to 300 feet (91.4 m) (6 x 50) away from the
pump. Do not add more than 300
Figure 3
(91.4 m) feet of inlet extension hose to
the pump.
5. Assemble your respirator by following the
manufacturer’s directions as described in
the respirator’s instruction manual. Be sure
the pump’s outlet pressure, measured by the
pressure gauge on the pump, is greater than
the minimum MSHA/NIOSH approved pressure required to operate the respirator.
The respirator’s minimum approved pressure will be found in the respirator’s instruction manual and/or on labels attached to the
respirator.
If you have any questions as to whether
or not your respirator is compatible with
this pump, call Bullard’s Customer Service
Department at 1-800-827-0423 or
1-859‑­234-6616.
6. Connect the respirator’s NIOSH approved air
supply hose(s) to the quick-disconnect outlet
coupler(s) on the pump (see
Figure 4).
Figure 4
9
A. OUTLET COUPLER SPLITTER ADAPTOR
If the respirator’s air supply hose(s) have
1/2” Industrial Interchange quick-disconnect
fittings and you want to supply air to one of
the following:
- TWO Half or Full Face Mask respirators using pump model EDP10
or
- THREE Half or Full Face Mask respirators
using pump model EDP16TE or EDP16HAZ
Connect the following Q.D. coupler splitter
adaptor to the pump (see Figure 5):
Figure 5
Cat. No. V24 - Double Outlet, One FlowThrough (GREEN) & One Shut-Off (RED).
B. CONNECTING AIR SUPPLY HOSE(S)
WITHOUT 1/2” QUICK-DISCONNECT
FITTINGS
If your respirator’s NIOSH approved air supply
hose will not attach to the pump’s standard
1/2” Industrial Interchange outlet coupler,
(see above) you can adapt your hose’s fitting
to the pump by converting the pump’s quickdisconnect outlet to 3/8” Female NPT with the
installation of one of the following adaptors
(see Figure 6):
Figure 6
Cat. No. V22 - Converts SINGLE outlet to
DOUBLE 3/8” female NPT pipe thread.
Cat. No. V23 - Converts SINGLE outlet to
SINGLE 3/8” female NPT pipe thread. A variety of quick-disconnect fittings may be used
to connect your air supply hose to the 3/8”
female pipe thread. Contact your respirator’s
manufacturer for the proper fitting (Hansen,
Foster, Snap-Tite, Schrader, etc.)
(see Figure 7).
Figure 7
10
Free-Air® Pumps
Instruction Manual
7. Before connecting your respirator to the
air supply hose, turn the pump on. Allow
the air to flow through the pump and
hose for a few minutes to purge or expel
any hose odors or moisture that may
have accumulated inside the hose.
11. When finished working, leave the work
area wearing the respirator with the air
still flowing. Once outside the contaminated area, remove the respirator, turn the
pump off, then disconnect the air supply
hose using the quick-disconnect couplers.
8. Connect the respirator to the air supply
hose using the quick-disconnect fittings.
9. With the air flowing, put on the respirator by following the directions in the
respirator manufacturer’s instruction
manual.
See the respirator’s instruction manual for
proper inspection, maintenance and storage procedures for the respirator you are
using.
10. Set the pump’s outlet pressure to within
the respirator’s approved pressure range
by adjusting the pressure adjustment
valve located on the outlet filter body.
To set the pressure adjustment valve,
loosen the lock nut. Once the desired
outlet pressure has been obtained,
retighten the lock nut firmly by hand to
maintain consistent outlet pressure. (see
Figure 8).
YOU ARE NOW READY TO ENTER THE
WORK AREA.
Figure 8
11
®
Maintaining the Free-Air Pump
Bullard Free-Air pumps consist of an elec-trically
driven air pump with four carbon vanes. The vanes
self-adjust as they wear and should last from
5,000 to 15,000 hours if properly maintained.
For the pump to operate at its optimum performance level, the following routine maintenance
procedures must be performed:
1. REPLACE THE INLET AND OUTLET
FILTERS REGULARLY
� WARNING
NEVER USE KEROSENE OR OTHER COMBUSTIBLE
LIQUIDS OR VAPORS WITH THIS PUMP. THEIR USE
MAY RESULT IN AN EXPLOSION WHICH MAY CAUSE
INJURY OR DEATH.
Directions for Flushing Pump
a. Before flushing, disassemble and remove the
following parts from the pump:
- Disconnect the respirator’s air supply hose
Dirty filters may inhibit air flow to the
respirator(s), and cause the motor to overload
and decrease vane life.
- Remove the pump’s inlet filter
- Replace the Carbofine outlet filter cartridge (Cat.
No. S17101) at least once every 200 running hours
or sooner if necessary.
b. With the pump running, pour several ounces of
approved safety solvent into the pump’s air inlet
port. Repeat the flushing if necessary.
- Replace the inlet filter (Cat. No. 23611), at least
once every 500 operating hours or sooner if
necessary.
2. FLUSH PUMP IF NECESSARY
Should excessive dirt, sand, foreign particles,
moisture or oil be permitted to enter the pump,
the carbon vanes will become sluggish and the
pump’s performance will deteriorate. This will
result in decreased outlet pressure or failure of
the pump to operate.
If the pump remains idle in a humid environment
for a long period of time, rust film may build up
in the pump’s chamber and rotor slots. This will
result in decreased outlet pressure or a failure to
operate at all.
If the above occurs, the pump should be flushed
with the following recommended solvent:
- Loctite Safety Solvent (Cat. No. S17931)
12
- Remove the pump’s outlet filter jar and outlet
filter cartridge
� WARNING
RUN THE PUMP FOR A SUFFICIENT TIME TO PURGE
ALL TRACES OF THE SOLVENT BEFORE REPLACING
THE FILTERS, RECONNECTING THE AIR SUPPLY
HOSE(S) AND USING THE RESPIRATOR.
3. AVOID RUNNING THE PUMP AT EXCESSIVE
PRESSURE
Avoid running the Free Air pump above 15 psig
(103 kPa) for any length of time. Running the
pump above 15 psig (103 kPa) could cause motor
damage and will create premature wear of the
carbon vanes.
NOTE
NEVER LUBRICATE THIS OIL-LESS PUMP.
THE MOTOR BEARINGS ARE GREASE
PACKED AND SEALED. THEY REQUIRE NO
FURTHER LUBRICATION.
Free-Air® Pumps
Instruction Manual
Free-Air® Pump Trouble
Shooting Guide
If your Bullard Free-Air pump is not working
satisfactorily, please follow the trouble shooting
steps below:
SYMPTOM: Pump Fails to Start or
Hums
1. Turn pump switch off and disconnect from the
power source.
2. Check for the correct electrical current as
shown on the motor plate and in the Electric
Motor Specification Chart on page 7 of this
manual.
3. The pump is equipped with a thermal overload
protector that turns the current off when subjected to electrical overloads. Check to be sure
that the circuit is not overloaded by the pump
and other electrical equipment.
4. Wait 15 minutes and restart.
6. Check that both the inlet filter (Cat. No. 23611)
and outlet filter (Cat. No. S17101)are clean and
replace if necessary. Dirty filters restrict air
flow.
7. Flush the pump with Loctite Safety Solvent (Cat.
no. S17931) to remove excessive dirt, sand,
particles, moisture or oil in the rotor assembly.
See the Maintenance Section on Page 12 of this
manual for proper directions on flushing the
pump.
When the parts are reassembled, attach the
respirator and turn the pump on, monitoring the
outlet pressure.
SYMPTOM: Outlet Pressure Too High
1. The pressure adjustment valve is set too high
- reset to a lower pressure. Be sure the outlet
pressure remains in the proper range for
the respirator as specified by the respirator
manufacturer - see the respirator’s instruction
manual.
SYMPTOM: Outlet Air Pressure Too
Low
2. Check the respirator’s air supply hose for kinks.
1. Be sure you know the proper pressure range for
the respirator - see the respirator’s instruction
manual.
1. 160°-200°F (71°-93°C) is normal output air
temperature when the pump is continuously
running. This heat is dissipated as it travels
through the respirator’s air supply hose until it
reaches ambient air temperature.
2. Be sure the respirator and air supply hose are
connected when the gauge reading is taken.
3. Check to see that the gauge is functioning properly. Replace the gauge if broken or malfunctioning.
4. Check to see that the outlet filter jar is seated
firmly into the filter housing’s O-ring so that no
air can escape. Replace the jar and/or O-ring if
damaged or worn.
5. Check to see that no air is escaping from the
relief valve in the outlet filter body. Reset the
pressure adjustment valve if necessary.
SYMPTOM: Pump Overheating
2. Make sure that both the inlet and outlet filters
are clean. Replace if necessary.
3. The pressure adjustment valve is set too high
- reset to a lower pressure. Be sure the outlet
pressure remains in the proper range for
the respirator as specified by the respirator
manufacturer - see the respirator’s instruction
manual.
4. Flush the pump with Loctite Safety Solvent (cat.
no. S17931) to remove excess dirt, sand, particles, moisture or oil in the rotor assembly.
13
Trouble Shooting Guide
continued
See the Maintenance Section on page 12 of this
manual for proper directions on flushing the
pump.
When the parts are reassembled, attach the
respirator and turn the pump on, monitoring its
performance for overheating.
5. The electrical circuit to which the pump is
connected is overloaded. Check the amperage
load of the circuit and disconnect other electrical equipment, if necessary, from that circuit.
SYMPTOM: Outlet Air Temperature Too Warm
1. Be sure that at least the first 50 feet (15 m) of
air supply hose closest to the pump is laid out
(not coiled) to permit excess heat to dissipate
from the hose.
2. Keep the air supply hose out of direct sunlight and off warm or hot surfaces.
3. Put a coiled section of the air supply hose in the
bottom of a large container. Fill the container
with water and ice and cover with a lid. For
best results, locate the container as close to
the worker as possible.
14
SYMPTOM: Outlet Air Temperature Too Cold
1. Let the pump warm up approximately 15 minutes before using.
2. Coil the first 25-50 feet (7.6-15 m) of air supply
hose closest to the pump.
3. Keep the air supply hose off cold surfaces.
SYMPTOM: Moisture In Air Supply Hose Line
1. Locate the air inlet filter in a dry, clean air
location, where breathable air can be assured
at all times.
2. With the air supply hose connected to the
pump, but not the respirator, turn the pump on
and let it run for approximately 15 minutes to
purge the hose of excessive moisture.
IF THESE STEPS FAIL TO RESOLVE THE
PROBLEM, CONTACT YOUR BULLARD
DISTRIBUTOR OR BULLARD CUSTOMER
SERVICE DEPARTMENT AT 1-800-827-0423 OR
859-234-6616.
Free-Air® Pumps
Instruction Manual
Replacement Parts List
REPLACEMENT PARTS AND ACCESSORIES FOR EDP10, EDP16TE AND EDP16HAZ FREE-AIR PUMPS
Cat. No.
Description
23611
244852
263552
S17101
S17931
V22
V23
V24
V50IN
V50EX
Inlet Filter
Outlet Filter Jar
Outlet Filter Assembly O-Ring
Outlet Filter Cartridge, Carbofine
Loctite Safety Solvent, 12 oz. (350 ml) Aerosol Can
Quick-Disconnect Coupler Adaptor. Converts pump’s quick-disconnect coupler
to DOUBLE 3/8” Female NPT
Quick-Disconnect Coupler Adaptor. Converts pump’s quick-disconnect coupler
to SINGLE 3/8” Female NPT
Quick-Disconnect Coupler Splitter/Adaptor. Converts pump’s Quick-disconnect
coupler to DOUBLE 1/2” Industrial Interchange Female Couplers (One FlowThrough, One Shut-Off)
Remote Inlet Air Hose Kit, 50 Feet (15 m) 1 per pump
Remote Extension Hose Kit, 50 Feet (15 m) 5 per pump maximum
15
EDP10
244852
Outlet Filter Jar
23611
Inlet Filter
S19681
Pressure Gauge
S7101
Outlet Filter Cartridge
S16483
Quick-Disconnect Coupler
263552
O-Ring
(not shown)
EDP16TE
15921
Service Kit
(not shown)
244852
Outlet Filter Jar
S17101
Outlet Filter Cartridge
23611
Inlet Filter
S19683
Pressure Gauge
S16191
QuickDisconnect
Coupler (Shutoff)
S16481
Quick-Disconnect
Coupler (FlowThrough)
263552
O-Ring
(not shown)
EDP16HAZ
S17101
Outlet Filter Cartridge
263552
O-Ring
(not shown)
16
244852
Outlet Filter Jar
15922
Service Kit
(not shown)
23611
Inlet Filter
S19683
Pressure Gauge
S16481
QuickDisconnect
Coupler (FlowThrough)
S16191
Quick-Disconnect
Coupler (Shut-Off)
15922
Service Kit
(not shown)
Free-Air® Pumps
Instruction Manual
PUMP WARRANTY
FREE-AIR® PUMP ONE YEAR LIMITED WARRANTY
Bullard warrants to the original purchaser that the Free-Air pump will be free of defects in material and
workmanship under normal use and service for a period of one (1) year from the date of purchase. E.D.
Bullard Company’s obligation under this warranty is limited to repairing or replacing, at its option, articles that are returned within the warranty period and that are, after examination, shown to E.D. Bullard
Company’s satisfaction to be defective, subject to the following limitations:
a) Free-Air pump must be returned to the E. D. Bullard Company with shipping
charges prepaid.
b) Free-Air pump must not be altered from its original factory configuration.
c) Free-Air pump must not have been misused, subjected to negligent use, or damaged in
transport.
d) The date of purchase is within the one year warranty period. (A copy of the
purchaser’s original invoice showing the date of purchase is required to validate warranty
coverage).
In no event shall Bullard be responsible for damages for loss of use or other indirect, incidental, consequential or special costs, expenses or damages incurred by the purchaser, notwithstanding that Bullard
has been advised of the possibility of such damages.
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE (1) YEAR FROM THE DATE OF PURCHASE
OF THIS PRODUCT.
TO RETURN GOODS: Written permission must be obtained before returning any material for any reason
whatsoever. Material returned for credit will be subjected to factory inspection. In-warranty product
of current design, will be subjected to a rehandling charge less freight originally allowed. All material
must be shipped with transportation charges prepaid. Bullard will issue a Return Material Authorization
number and shipping label which must be affixed to all returns to facilitate handling and reduce risk
of loss.
Products which are obsolete or made to special order are not returnable.
Warranty information can be obtained from, and defective articles should be sent, shipping charges
prepaid to:
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll-Free: 800-877-BULLARD
Phone: 859-234-6616
17
Free-Air® Pumps
Instruction Manual
Air Filter Replacement
Schedule
Regular inspection and replacement of the air filters will prevent extensive and costly pump repair. Dirty
or clogged filters can be responsible for failure of the pump to build up outlet pressure and eventual
overheating.
-Replace the Carbofine outlet filter (Cat. No. S17101) at least once every 200 running hours or sooner if necessary.
The outlet filter cartridge is multi-layered with 40-micron size particles of activated carbon, a sorbent
bed with an exposed carbon surface of more than 15,000 square feet (1,615 sq meters).
-Replace the medium efficiency inlet filter (Cat. No. 23611) at least once every 500 running hours or
sooner if necessary.
The inlet filter keeps moisture as well as particulates out of the air supply and helps protect the pump’s
carbon vanes.
We recommend the following chart be used to monitor and maintain a routine air filter
replacement schedule.
CARBOFINE OUTLET FILTER
(Cat. No. S17101)
Cumulative
Pump
Operating
Hours
Last Filter
Replacement
Date
200
400
600
800
1,000
1,200
1,400
1,600
1,800
2,000
MEDIUM EFFICIENCY INLET FILTER
(Cat. No. 23611)
Employee
Responsible
(Initial)
Cumulative
Pump
Operating
Hours
Last Filter
Replacement
Date
Employee
Responsible
(Initial)
500
1,000
1,500
2,000
2,500
3,000
3,500
4,000
4,500
5,000
ISO 9001
certified
©2010 Bullard. All rights reserved.
Americas:
E.D. Bullard Company
1898 Safety Way
Cynthiana, KY 41031-9303
Toll free: 877-BULLARD (285-5273)
Tel: 859-234-6616
Fax: 859-234-8987
www.bullard.com
Europe:
Bullard GmbH
Lilienthalstrasse 12
53424 Remagen • Germany
Tel: +49-2642 999980
Fax : +49-2642 9999829
www.bullardextrem.com
6093500182B (0510)
Asia-Pacific:
Bullard Asia Pacific Pte. Ltd.
LHK Building
701, Sims Drive, #04-03
Singapore 387383
Tel: +65-6745-0556
Fax: +65-6745-5176
www.bullard.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement