instruktion

1
Teknisk specifikation
2
Användarhandbok till kontrollenheten
3
Bilaga till användarhandboken
4
Instruktion vid skjutplats
5
Simulera skjutning med demoskott
6
Hur göra om någon ändrat på
inställningarna i kontrollenheten
7
Ändra inställningen från 10 m till 50 m
i kontrollenheterna.
8
Instruktion för hantering av programvara
samt underhåll av tavla
System 7
Användarhandbok
www.sius.se
Användarhandbok System 7, 2011-08-18
Användarhandledning för kontrollenheten CU941
Följande användarhandledning beskriver kontrollenhetens funktioner för en 80
m löpande älgbana, 50 m löpande viltbana och inskjutningsbana.
Innehållsförteckning
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Bildskärmslayout
Manövrering
Inställningar
Skjutprogram
Kontrollera menyn
Tavlor (fria serier)
Fasta Program
Användarprogram
Match
Kommunikation
Underhåll
Log
Taveltest
Tavlans mätelektronik (LME)
PC dator
Kontrollenhet
Uppstartsvarianter
Demoskott
Fjärrkontroll
Återkommande frågor (FAQ)
Begreppsförklaringar
3
6
9
9
10
10
11
12
12
12
13
14
14
15
16
16
17
17
17
19
20
Sida 2 av 20
Användarhandbok System 7, 2011-08-18
1.
Bildskärmslayout
Information om pågående skjutning visas i olika fält på bildskärmen.
Rubriklist
Listfönster
Skottfönster
Programförlopps
fönster
Funktionstangentfönster
Statusfönster
Tavelfönster
I ovanstående exempel har valts layouten ”Klassisk”. Vid leverans är layouten
inställd på ”Final”. Tavelfönstret är i detta fall större och inkluderar de både
nedre rutorna. Vid träffbildsskytte kan det vara en fördel att använda ”Klassisk”
layout i och med att informationen om
1.1.
Tavelfönster
Med funktionstangenten Zoom kan olika förstoringssteg väljas. Eller med
handkontrollerns Zoom knapp. Visningsskalan ändras då i motsvarande grad i
tavelfönstret. Symbolen för det senast avfyrade skottet kan ställas in oberoende
av symbolen för de övriga skotten. Som fabriksinställning har för båda
symbolen ”Cirkel” valts. Kontrollenheten visas då skotthålen i överdriven
storlek.
Informationen ”Skala” medger en bedömning av tavelstorleken. Därigenom kan
en uppfattning får om avståndet mellan skott och avståndet skott till
tavelcentrum. Visningen av kaliber ((tolken storlek) och skala kan urkopplas via
inställningarna. Detta är gjort som fabriksinställning för jakt.
Sida 3 av 20
Användarhandbok System 7, 2011-08-18
För inskjutningstavlan bibehålls dock kaliber informationen. Man får då en linjal
som ger en bra uppfattning om storleken.
När bomskottsensorn är inkopplad visas i nedre högra hörnet denna symbol.
När nedanstående korslagda markörspadar visas har något inträffat vid
skjutplatsen. Bomskottsensorn har icke registrerat att ett skott avfyrats:
1.2.
Skottfönster
I detta fall visas ett fönster från älgen. Skott nr 2 har tagit i ring 5 och siffran ett
till höger talar om att skottet är innanför det anatomiska träffområdet på älgen.
En 0 anger att träffen tagit utanför det anatomiska träffområdet.
Vid vildsvinsskytte bl.a. samt skytte mot inskjutningstavlan visas ett P efter
tvåan vilket anger att skottet är ett provskott.
1.3.
Listfönster
Siffran till vänster anger skottnumret. Pilen visas träffläge sett från tavlans mitt.
Därefter följer valören. Flaggan till höger om siffran 5 betyder att en träff i
innerfemman föreligger. I utskriften på skrivaren framställs innerfemman som
”*”. Därefter följer träff inom det anatomiska träffområdet som visas som 1. En
0 anger träff utanför det anatomiska träffområdet.
1.4.
Programförloppsfönster
Programförloppsfönster kan bara ses om det valts in, och det kan urkopplas via
inställningarna. I fabriksinställningen visas detta fönster.
Sida 4 av 20
Användarhandbok System 7, 2011-08-18
Programförloppsfönstrets innehåll beror på det inställda programmet. I
ovanstående figur visas ett ”Fast Program” för vildsvinsskytte, där antalet skott
är fast fördefinierat. Den aktiva gruppen visas mot vit bakgrund. Symbolen ”>>”
anger att det efter gruppen ”E10” följer ytterligare grupper. På liknande sätt
sker visning vid användarprogram och vid en Match.
Vid ’fria serier’ visas endast de tre avfyringsvarianterna P- (provskott), E(enkelskott) och D- (dold skottserie). Det går att välja fritt mellan
avfyringsvarianterna och antalet skott är inte fördefinierat.
1.5.
Statusfönster
Det förekommer ett antal viktiga statusinformationer:
Med mindre text visas dessutom ytterligare statusinformation:
Sida 5 av 20
Användarhandbok System 7, 2011-08-18
1.6.
Rubriklist
I rubriklisten visas tavelnumret samt aktuellt datum och klockslag. Formatet för
datumvisning kan ändras.
1.7.
Funktionstangentfönster
Funktionstangenterna F1 till F5 har olika funktioner. Beroende på i vilken mod
Kontrollenheten arbetar kan funktionstangenterna tilldelas olika funktioner.
I funktionstangentfönstret visas samma information som på den lilla LCDdisplayen på kontrollenhetens tangentbord. Men LCD-displayen är för varje
funktionstangent begränsad till fyra tecken (se listan över förkortningar i ”Bilaga
till driftsinstruktion för System 7”). Hur navigering kan ske i menyträdet beskrivs
i avsnitt ”Manövrering”.
2.
Manövrering
2.1.
Manöversätt
Kontrollenheten kan användas på olika sätt. Manövrering via tangentbordet
(meny) är den gynnsammaste varianten. Samtliga funktioner som är tillgängliga
hos Kontrollenheten kan styras via tangentbordet. Undantagna från detta är
endast användarprogrammen. Dessa kan enbart laddas via en
streckkodsläsare eller från en central dator.
Den stora fördelen med manövrering via streckkoder är att de viktigaste
instruktionerna kan sammanställas på ett pappersark, varigenom
manövreringen kan reduceras till det nödvändigaste.
Manövrering med fjärrkontrollen är ytterligare ett sätt för att enkelt föra in en ny
skytt och starta om skjutprogrammet.
2.2.
Meny (manövrering via tangentbord)
Menyn är strukturerad som ett träd. På liknande sätt som hos moderna
datorsystem är de befintliga elementen indelade i kataloger, mappar och filer
(instruktioner). Trädets rot är i översikten placerad i mitten. Från roten förgrenar
sig katalogerna och mapparna. Ju mera katalogerna och mapparna är
förgrenade desto mera detaljerade är informationen och instruktionerna.
Sida 6 av 20
Användarhandbok System 7, 2011-08-18
Trädets kompletta struktur visas överskådligt i ”Bilaga till driftsinstruktion för
System 7”. Dessutom motsvarar denna struktur samtidigt
innehållsförteckningen för streckkodsbeskrivningarna. För navigering inom
trädet används följande tangenter och funktionstangenter:
Sida 7 av 20
Användarhandbok System 7, 2011-08-18
När ett skjutprogram väljs växlar menyn automatiskt till kontrollmenyn.
I kontrollmenyn finns direkt de viktigaste instruktionerna tillgängliga vid den
valda programtypen. Se avsnitt ”Programstyrning”.
2.3.
Streckkoder
Vid inläsning av en streckkod skall streckkodsläsaren placeras direkt och ca 12 cm rakt ovanför den aktuella streckkoden. Därefter trycks inläsningsknappen
in.
För en fungerande manövrering av systemet måste streckkoderna föreligga
som högvärdiga utskrifter eller kopior.
Streckkodsläsaren kvitterar inlästa streckkoder genom olika ”beep”-signaler. Ett
”beep” betyder godkänd inläsning av streckkoden, två ”beep” innebär att
Sida 8 av 20
Användarhandbok System 7, 2011-08-18
instruktionen visserligen har blivit korrekt inläst men att den inte stöds av
systemet eller att den för tillfället inte kan utföras. Vid tre ’beep’ föreligger ett
inläsningsfel eller en ogiltig streckkod.
Tillåtna streckkoder är endast de som är listade i ”Bilaga till driftsinstruktion för
System 7” eller sådana som framställts med hjälp av Barcode-biblioteket. Andra
streckkoder kan leda till funktionsfel hos enheten.
Kontrollenheten (endast CU941) har på höger sida ett hårdvarugränssnitt
(kontaktdon) till vilket en streckkodsläsare kan anslutas. Med denna
streckkodsläsare kan alla inmatningar göras som också kan göras via
tangentbordet. Därutöver kan även användarprogram läsas in som tidigare
framställts med datorprogrammet Barcode-Library (Gratisprogram hämtas från
hemsidan www.sius.com) eller med SIUSDATA®.
Streckkoderna är organiserade på samma sätt som Kontrollenhetens
tangentbord. I ”Bilaga till driftsinstruktion för System 7” är samtliga tillgängliga
streckkoder listade. Menyträdet kan därvid användas som en kompletterande
innehållsförteckning.
Som streckkoder används ”Interleave 2 of 5”-koder. Koderna är skyddade med
en kontrollsiffra. Därigenom filtreras läsfel och felaktiga koder.
2.4.
PC
Med mjukvaran SIUSDATA® kan alla instruktioner sändas samtidigt till
samtliga kontrollenheter som är anslutna till samma nätverk. Med denna
funktion är det enkelt att hos alla kontrollenheter samtidigt ändra samma
inställningar eller ladda ett program. Tillvägagångssättet beskrivs i
dokumentationen för SIUSDATA®.
3.
Inställningar
Kontrollenheten erbjuder ett stort antal inställningsmöjligheter. Praktiskt taget
alla kundbehov kan täckas med dessa inställningar. Från språket via ett
uppstartningsprogram till diverse presentationsvarianter kan allt programmeras.
Hur inställningarna är organiserade framgår mest överskådligt i menyträdet.
Vid leverans har vi föreslagit en kundinställning. Dessa inställningar kan
användaren ändra.
Filter är en funktion för att dölja inställningar som inte används.
4.
Skjutprogram
De program som kan lagras i kontrollenheten kan indelas i fyra grupper:
Sida 9 av 20
Användarhandbok System 7, 2011-08-18
5.
Kontrollera menyn
6.
Tavlor (fria serier)
I en Fri Serie är antalet skott som skall skjutas inte fastlagt i förväg. Skytten kan
själv avsluta skjutningen genom grupptotal eller stotal. På så sätt kan valfria
program skjutas. Något fast föreskrivet förlopp för detta kan emellertid inte fås
via Kontrollenheten . Detta funktionssätt är därför speciellt lämpligt för vana
användare som är väl förtrogna med de program som skall skjutas. Efter att en
Fri Serie ställts in visas följande i programförloppsfönstret:
Sida 10 av 20
Användarhandbok System 7, 2011-08-18
De tre bokstäverna betecknar de tre skjutarterna som finns tillgängliga. Vid ”P-”
kan provskott avfyras. Valörerna för provskotten adderas inte till den
sammanlagda totalen. Genom att trycka på funktionsknappen ”\Enkelskott” kan
växling till ”E-” ske. Enkelskott visas direkt efter varje enskilt skott. I motsats
härtill visas serieskott under ”D-” först efter att en seriegrupp avslutats eller
efter att uttryckligen instruktionen ”Visa” utförts. Bindestrecket ”-” betyder att det
är fråga om en öppen grupp. Antalet skott som kan skjutas är valfritt. Vid en Fri
Serie kan följande instruktioner utföras.
7.
Fasta Program
Fasta Program är lagrade i Kontrollenhetens icke flyktiga minne. Ett Fast
Program ger en fast ordningsföljd för skottgrupperna. Kontrollenheten
garanterar att det bestämda förloppet följs. Fasta Program är exempelvis
programmet för löpande älg med två skott per löp och två löp per serie.
Programförloppsfönstret hos detta Fasta Program har följande utseende:
Ett nytt Fasta Program kräver en ny programversion hos kontrollenheten.
Sida 11 av 20
Användarhandbok System 7, 2011-08-18
8.
Användarprogram
Användarprogram kan skapas med PC-mjukvaran Barcode-Library eller i SIUS
DATA®. Med sådana program kan egna programförlopp definieras. Det är
också möjligt att sammanställa ett användarprogram där tavelbilden växlar
under programmets utförande. Det är emellertid inte möjligt att samtidigt ändra
andra inställningar med streckkoden för användarprogrammet. När det för ett
program till exempel krävs en viss utskrift måste denna ställas in separat.
Inställning av användarprogram kan ske via streckkoder eller en PC. Likaså är
det inte möjligt att konfigurera användarprogram med hjälp av tangentbordet. I
övrigt fungerar användarprogram identiskt lika som Fasta Program.
9.
Match
Skytten kan individuellt växla från provskott till tävlingsskott. Detta kan ske ex.
via fjärrkontrollen genom att trycka på knappen Match. Så länge inget
tävlingsskott avfyrats kan skytten återgå till provskott.
10.
Kommunikation
De olika systemkomponenterna (Kontrollenhet, LON-mätelektronik (tavlan), och
PC) är sammanlänkade via en fältbuss LON. Genom detta kommunikationsnät
kan systemkomponenterna kommunicera med varandra. LON-mätelektroniken
överför skottrådata till kontrollenheten så att kontrollenheten kan beräkna
skottvalören och infoga denna korrekt i det pågående programmet. Detta är
den viktigaste förbindelsen. Utan kommunikation från kontrollenheten till LONmätelektroniken kan ingen skjutverksamhet startas. Ett avbrott i förbindelsen
med LON-mätelektroniken signaleras av kontrollenheten genom indikeringen
”OFFLINE” i statusfönstret.
Kontrollenheten ger förutom skottinformationen även annan information till
PC:n, för att där data från alla banor kan sammanfattas och utvärderas. För att
förhindra en överbelastning av nätverket indelas det vid installation av större
anläggningar med flera banor i olika segment. Kraven på kablering och
användning av routers beskrivs i hårdvaruinstruktionen.
För felfri funktion krävs att systemkomponenterna adresseras via en adress
som är indelad i en subnet- och nodadress. Nodadressen definierar
systemkomponenterna själva. Alla systemkomponenter för en bana (lane)
måste vara inställda för samma subnet-adress (tavelnummer). Detta sker
antingen via en LNR-box (Lane Number Box) och tillhörande vridströmbrytare
eller genom inställningar och programmering som hos kontrollenheten (se
”System\Hårdvara\Manöverenhett\Set Subnet” och
”System\Hårdvara\Figur\Anslut”).
Systemkomponenterna detekterar automatisk om de adresserade
komponenterna är tillgängliga.
Sida 12 av 20
Användarhandbok System 7, 2011-08-18
11.
Underhåll
11.1. Rapporter
Rapporten över inställningarna har reducerats så långt att den endast omfattar
inställningar som skiljer sig från fabriksinställningarna.
Efter fullständig inställning av kontrollenheten efter användarens önskemål är
det meningsfullt att skriva ut och arkivera rapporten över inställningarna. Med
hjälp av rapporten kan även en reparerad eller utbytt manöverenhet åter ställas
in för den önskade konfigurationen.
11.2. Skottrapport
Skottrapporten kan användas för redovisningar. Skottrapporten innehåller
detaljerade uppgifter om de olika skotthändelserna.
Sida 13 av 20
Användarhandbok System 7, 2011-08-18
12. Log
I den interna loggen är alla händelser lagrade som erfordras för
dokumentationen och för en eventuell återställning efter ett strömavbrott. Varje
händelse visas på minst två rader. I den övre raden anges tidpunkten för
händelsen i 1/100-sekunder. I den andra raden skrivs händelsens klass och en
representativ text ut. Vid skott dokumenteras koordinaterna för skottläget på en
ytterligare linje. Nedan förklaras de viktigaste uppgifterna i en loggutskrift.
13. Taveltest
Utskrift av taveltesten:
Sida 14 av 20
Användarhandbok System 7, 2011-08-18
Taveltesten ger information om mjukvaru- och hårdvaruversionerna samt
information om den LON-mätelektronik som är inställd på samma tavelnummer
som den manöverenhet från vilken taveltesten utlöses. Betydelsen av de olika
värdena förklaras i följande tabell:
PIC betecknar hårdvaruversionen och ”Version\Release” betecknar
mjukvaruversionen avseende LON-mätelektroniken. Tidsdifferensen erhålls
från den tidpunkt vid vilken LON-mätelektroniken har avsänt taveltesten minus
den tidpunkt vid vilken kontrollenheten utvärderar taveltesten. En tidsdifferens
lägre än 100 millisekunder är normal. Större tidsdifferenser tyder på felaktig
tidssynkronisering.
14. Tavlans mätelektronik (LME)
LON-mätelektroniken omfattar nedanstående komponenter. Dessa
komponenter kan detekteras via taveltesten (”\System\Underhåll\BITtest\
Taveltest”).
Sida 15 av 20
Användarhandbok System 7, 2011-08-18
I mätelektroniken måste samma tavelnummer (subnet-adress) finnas som hos
den tillhörande kontrollenheten. Tavelnumret kan endast programmeras via
kontrollenheten. Förfarandet beskrivs i kap.”Anslutning av tavlan” eller i ”Bilaga
till driftsinstruktion för System 7” under ”\System\Hardvåra\Figur\Anslut”.
Alternativt kan dessutom tavlorna bestyckas med en LNR-box eller en LNRkretskort. I ett sådant fall behövs inte programmeringen via kontrollenheten.
15. PC dator
Med hjälp av en ”LON-dongle” kan även en vanlig dator (PC) anslutas till LONnätverket. Det finns ett antal programvaror som tagits fram för drift tillsammans
med manöverenheterna.
16. Kontrollenhet
Kontrollenheten (CU931 eller FPE06) innehåller huvuddatorn för varje
träffindikeringsanläggning. Det finns olika mjukvaruprogram som kan laddas in i
dessa enheter. I den föreliggande dokumentationen beskrivs versionen
”System 7”.
I kontrollenheten finns följande komponenter:
Sida 16 av 20
Användarhandbok System 7, 2011-08-18
LON-programvaran och Manöverenhet-programvaran kan laddas med PCprogramvaran LONORG®. För Boostrap-loader-programvaran är denna
funktion ännu inte tillgänglig. Altera-versionen kan ändras genom byte av en
socklad IC-komponent. Genom att trycka ned Help-tangenten fås en utskrift av
ovanstående uppgifter.
17. Uppstartsvarianter
18. Demoskott
Ett demoskott utlöses med Ins-tangenten under förutsättning att anläggningen
är inställd för ”Demo”.
19. Fjärrkontroll
Sida 17 av 20
Användarhandbok System 7, 2011-08-18
Fjärrkontroll lådan RC941 kan anslutas till kontrollenheten. Den är tänkt för
skyttar så att de från sin placering kan inmata de viktigaste instruktionerna utan
att behöva lämna sin placering.
Zoom-knapp
Med ZOOM-knappen kan, såsom redan beskrivits i kap. ”Manövrering”, tavlans
bildsegment förstoras.
Meny-knapp
Under förutsättning av inställningen ”\System\Hardvåra\RC92\Match Meny” är
aktiverad kan man med Meny-knappen få kontrollmenyn som listfönster direkt
på monitorn.
Med Meny- och Match-knappen kan sedan urvalet i detta fönster flyttas uppåt
eller nedåt. När rätt instruktion valts ut kan denna bekräftas med Enterknappen (Zoom-knappen). Om ingen aktion skall äga rum måste instruktionen
”Cancel” utföras. Meny försvinner omedelbart när någon annan händelse (t.ex.
skott eller felmeddelande) föreligger.
Match-knapp
Match-knappen har, förutom den ovan beskrivna navigeringsfunktionen, under
en ISSF-ställningsMatch en särskild funktion. Skytten kan genom nedtryckning
av Match-knappen individuellt växla från prov- till tävlingsskott. Han får även
återgå till provskott såvida han inte har startat Matchen. Denna funktion kan
genomföras via RC941 (Fjärrkontroll lådan) eller på kontrollenheten med dess
funktionstangenter. Efter provskott kan skytten växla tillbaka till det ordinarie
programmet genom att trycka ned Match-knappen. Vid Fria Serier kan man
med hjälp av Match-knappen stega genom prov, enkelskott och dolda skott.
Med programmet DIANA kan Matchknappen vid viltmålsskytte användas för att
föra in en ny figur vid vändning av vagnen..
Sida 18 av 20
Användarhandbok System 7, 2011-08-18
20. Återkommande frågor (FAQ)
– Varför är en viss instruktion eller en viss katalog inte åtkomlig via menyn?
Med filterfunktionen kan menyområden undantas från visning. Se därför till att
filtren är inställda enligt de individuella behoven.
– Hur kan anläggningen genomtestas?
I demo-moden kan man med Ins-tangenten hämta skott från
LONmätelektroniken. Därigenom testas kommunikationen med
LONmätelektroniken och funktionen hos stora delar av kontrollenheten. Demomoden kan aktiveras/deaktiveras via ”\System\Inställningar \Annan\Demo”.
Aktuell aktiveringsstatus visas i statusfönstret.
– Kontrollenheten förblir ”OFFLINE” och skotten visas inte i det inställda
programmet.
Kontrollenheten kan inte kommunicera med LON-mätelektroniken. Kontrollera
LON-mätelektronikens strömförsörjning samt konfigurationen av tavelnumret.
Kontrollera kableringen och anslut eventuellt LON-mätelektroniken på nytt. (Se
”Anslutning av tavlan”.)
– Kontrollenheten startar alltid med engelska som valt språk.
Inställningarna inklusive språkvalet förblir intakta även vid ett strömavbrott. Det
förloras först när buffertbatteriet är urladdat. Kontrollenheten visar (Lågt batteri
eller CRC fault) efter uppstart i listfönstret och ger under startförloppet tre
’beep’-signaler i följd.
– Hur kan man skjuta kommenderat på en skjutplats?
Manöverenheterna kan fjärrstyras med PC-programvaran SIUSDATA®. Med
denna programvara kan alla anslutna manöverenheter kontrolleras och
konfigureras.
Sida 19 av 20
Användarhandbok System 7, 2011-08-18
21. Begreppsförklaringar
Sida 20 av 20
Föreg. serie
Skrivt ut
Skotträknare
Ogiltigt skott
Log
Bilaga till driftsinstruktion för
System 7
Rapport
Symbol
Form
Storlek
Invertera
Sista skott
Last Shot Window
Visa
Deferred Shots
Visa 10X
Symbol
Skott
Standard
ISSF
Rörligt mål
Skidskytte
10m
ISSF
Schweiz
25m
Schweiz
A
B
ISSF
CISM
Schweiz
Skriver
F1 Figurer
300m
Nollställa skottnummer
Delsumma
Layout
Funktions tangenter
Manöverenhet
Status blinkar
Övningsfönster
Large font in Listwindow
Grupp
Belgium
Jakt
Skandinavien
Militär
Övrigt
Övrigt
Inställningar
ISSF
Rörligt mål
Femkamp
Övrigt
10m
ISSF
CISM
Sui
25m
Meddelande
Rörligt mål
Simulera resultattavla
Divisor
F2 Program
ISSF
CISM
Militär
Språk
F4 System
50m
Sui
Övrigt
Schweiz
Home
300m
Justera tid
Datumformat
Möjliggöra Repetering
återställa fria serier
Automatisk uppstart
SC-Programs
Start
Single Execution
Scale Factor
Set Scale Factor
Target Alternative
Automatisk nollställning
Övrigt
Skandinavien
Övrigt
Skandinavien
Distans
Kategorie
Vapen
Användar grupp
Funktion
Mode
Filter
Övrigt
Jakt
Kaliber
Zoom
TOTAL
Resultat
Utskrift
Repetera
SC-Programs
Felfunktion
Avbryt
Radera tavlan
Ställ in timer
Övrigt
Starta timer
Timer
Nollställ timer
Ta bort timer
Legalisering
ange vapen
Ange ställning
Skytt ID krav
Text
MTP
MTP
Parametrar
Tid
OP
Lag mästerskap
A
B
Övrigt
FS
F5
Krav
Use Always
Control Mode
Demo
F3 Kontrollera
Underhåll
Kontroll inställningar
Inställningar
Skotträknare
Rapport
Ogiltigt skott
Log
Debug
BIT-test
Taveltest
Tangentbord
Resultattavla
Nollställa monitor
Resultattavla
Resultattavla
Meny
Manöverenhet
Set subnet
Info
RC92
F5 Logga in
Legalisering
Vapentyp
Ställning
Skytt nummer
Hårdvara
Figur
Match Meny
Figur byte
Känslighet
Bandmatning
Use Always
Use Always
Anslut
Time Control Unit
SIUS AG
BASYS7AH1SR1
Menu.mmp - 21.03.2005
Visa meddelanden
Info tavelmatning
Visa figurnamn
Kaliber
Indikera
ISSF
CISM
ISSF
DJV
SWE
Use Always
Skriv ut skjutprotokoll
Tiondel
Provskott
Delsumma
Print Overtime
Antal tomrader
Skandinavien
Norge
Use Always
Visa format
Tiondel
Radera tavlan efter skott
Presentation
50m
Skidskytte
Utskriftsformat
Kors skott
Ogiltigt skott
Bästa skott
Kolumnkonfiguration
ISSF
Gevär
Finkaliber
Grovkaliber
Form
Storlek
Invertera
Time Control Unit
Duell mode
Graphic Printer Modell
Im Langhag
1
Skott
sensor
CH-8307 Effretikon
+41 (52) 354 60 60
Fax: +41 (52) 354 60 66
www.sius.com
[email protected]
Reload
Reprint
Shot Counter
Invalid shots
Log
User Manual Appendix
System 7
Reports
Symbol
Last Shot
Last Shot Window
10m
ISSF
Switzerland
25m
Display Inner ten
Form
Size
Inverse
Shot
Standard
ISSF
Switzerland
A
B
F1 Targets
300m
Group
Italy
Austria
Hunting
Scandinavia
Full Bore
B
C
1/x
Other
Other
ISSF
Running Target
Pentathlon
Other
10m
ISSF
CISM
Sui
Other
25m
Running Target
Simulator SCB
Divisions
Language
F4 System
Language
Adjust Clock
Time
Date format
Enable Repeat
Free series start setting
Startup program
SC-Programs
Start
Single Execution
Scale Factor
Set Scale Factor
Target Alternative
Enable Autoreset
50m
Home
F2 Programs
ISSF
CISM
Switzerland
Other
300m
Scandinavia
Other
Military
Distance
Category
Weapon
User Group
Function
Mode
Filter
Full Bore
Austria
Scandinavia
Calibre
Use Always
Control Mode
Demo
Other
Settings Control
Hunting
Zoom
TOTAL
Score
Print screen
Repeat
SC-Programs
Malfunction
Abort
Clear target window
Set Timer
Other
Start Timer
Timer
Reset Timer
Remove Timer
Reports
Settings
Shot Counter
Invalid shots
Log
Debug
Self Test
Target test
Keyboard
Scoreboard
Maintenance
F3 Control
Control unit reset
SCB
SCB
Menu
Control unit
Set Subnet
RC92
Legalisation
Weapon required
Position required
Firer number required
Requirements
Info
Hardware
F5 Logon
Legalisation
Weapon Type
Position
Firer number
SIUS AG
BASYS7AH1ER1
Menu.mmp - 21.03.2005
Display Messages
Target Feed Message
Text
MPI
MPI
Parameter
Sui
Other
OP
Group championship
A
B
Other
FS
F5
Message
Display target name
Display calibre
Indication
ISSF
CISM
ISSF
DJV
SWE
Reset Shot Number
Subtotal
Layout
Function Keys
Control unit
Status flashing
Practice progress window
Large font in Listwindow
Other
Settings
Norway
Target
Match Menu
Target changer
Sensitivity
Use Always
Paper feed
Use Always
Connect
Distance Index
Time Control Unit
Use Always
Print Protocol
Secondary Score
Sighters
Subtotal
Print Overtime
Number of line feeds
Printing
Belgium
Military
Use Always
Screen-format
Secondary Score
Clear target after shots
Presentation
Scandinavia
Norway
Print-format
Cross Shot
Illegal Shot
Best shot
Column Configuration
50m
Biathlon
ISSF
CISM
Switzerland
Screen
Deferred Shots
Symbol
ISSF
Running Target
Biathlon
Other
Rifle
Small Bore
Big Bore
Form
Size
Inverse
Time Control Unit
Duel mode
Im Langhag
1
Graphic
Printer Model
Shot
sensor Effretikon
CH-8307
+41 (52) 354 60 60
Fax: +41 (52) 354 60 66
www.sius.com
[email protected]
Contents
English
Page
0
Targets
0
10m
ISSF
Running Target
Biathlon
Other
0
0
0
0
25m
ISSF
Switzerland
0
0
0
50m
ISSF
Switzerland
Rifle
Small Bore
Big Bore
Biathlon
0
0
0
0
0
0
0
300m
ISSF
CISM
Switzerland
A
B
Scandinavia
Norway
Belgium
Other
Italy
09.08.2010
0
0
0
0
0
0
0
0
0
0
0
Contents
English
Page
Austria
Hunting
Scandinavia
Military
0
0
0
0
Full Bore
Norway
0
B
C
1/x
Other
0
0
0
0
0
Programs
0
10m
0
ISSF
Running Target
Pentathlon
Other
0
0
0
0
25m
ISSF
CISM
Sui
Other
0
0
0
0
0
50m
ISSF
CISM
Running Target
ISSF
DJV
SWE
09.08.2010
0
0
0
0
0
0
0
Contents
English
Page
0
Sui
Other
0
0
300m
ISSF
CISM
Switzerland
OP
Group championship
A
B
Other
FS
F5
Scandinavia
Other
0
0
0
0
0
0
0
0
0
0
0
0
Other
Full Bore
Austria
Scandinavia
Military
Hunting
Control
Zoom
TOTAL
Score
Print screen
Repeat
09.08.2010
0
0
0
0
0
0
0
0
0
0
0
0
Contents
English
Page
0
SC-Programs
Malfunction
Other
0
0
Abort
Clear target window
Timer
Set Timer
Start Timer
Reset Timer
Remove Timer
0
0
0
0
0
0
0
System
0
Reports
0
Reload
Reprint
Shot Counter
Invalid shots
Log
0
0
0
0
0
Settings
Presentation
0
Shot
0
0
Last Shot
Symbol
0
Form
0
Size
0
Inverse
0
Last Shot Window
0
Screen
0
Deferred Shots
0
Display Inner ten
Standard
Symbol
09.08.2010
0
0
0
0
Contents
English
Page
Form
0
Size
0
Inverse
0
Print-format
0
Use Always
0
Screen-format
Secondary Score
Clear target after shots
0
Cross Shot
Illegal Shot
Best shot
0
0
0
0
0
Printing
Column Configuration
0
Use Always
0
Print Protocol
Secondary Score
Sighters
Subtotal
Print Overtime
Number of line feeds
0
Reset Shot Number
Subtotal
0
0
0
0
0
0
0
Other
Control unit
Layout
Function Keys
Status flashing
Practice progress window
Large font in Listwindow
Message
Display Messages
Target Feed Message
Display target name
Display calibre
Indication
Parameter
0
0
Group
09.08.2010
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Contents
English
Page
0
MPI
0
Text
MPI
0
Simulator SCB
Divisions
0
0
Language
Language
Time
0
0
Adjust Clock
Date format
0
0
0
Other
0
Start
Enable Repeat
Free series start setting
Startup program
SC-Programs
Single Execution
Scale Factor
Set Scale Factor
Target Alternative
Enable Autoreset
Filter
Distance
Category
Weapon
User Group
Function
Mode
Calibre
Use Always
09.08.2010
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Control Mode
Demo
0
Settings Control
0
0
Contents
English
Page
Maintenance
0
Reports
0
Settings
Shot Counter
Invalid shots
Log
Debug
Self Test
Target test
Keyboard
Scoreboard
Control unit reset
0
0
0
0
0
0
0
0
0
0
Hardware
0
SCB
SCB
0
Control unit
0
Menu
Set Subnet
0
0
0
RC92
Match Menu
0
0
Target
Target changer
Sensitivity
Use Always
Paper feed
0
0
0
0
Use Always
0
Connect
Distance Index
0
Time Control Unit
Time Control Unit
09.08.2010
0
0
0
0
Contents
English
Page
Duel mode
Graphic Printer Model
Shot sensor
0
0
0
Logon
0
Info
0
Requirements
Legalisation
Weapon required
Position required
Firer number required
Legalisation
Weapon Type
Position
Firer number
09.08.2010
0
0
0
0
0
0
0
0
0
09.08.2010
SIUS AG (c) 2004
1 / 112
Targets
Targets
Free series are programs which do not prescribe any set numbers of shots. They are especially suitable for completing open training
courses. With free series all official shoots can be simulated.
10m
The directory 10m is the compilation of all target images which typically are used over a distance of 10 metres.
ISSF
Official targets of the ISSF are filed in this directory.
Air Rifle
10 metre running target; ISSF Rules, Section
6.3.2.3; diameter 45.5mm; black reflector from ring 4 06000019000201(62)
to 9
Air Pistol
10 metre air pistol target; ISSF Rules, Section
6.3.2.6; diameter 155.5mm; black reflector from ring
7 to 10
06000019000203(56)
Switzerland
Targets that are used only in Switzerland are stored in this directory.
Air Rifle
10 metre target with the dimensions of the official
ISSF target. But unlike the latter, with the secondary
score in one hundredth rings instead of the one
tenth ring score of the ISSF.
06000019000205(50)
Air Pistol
10 metre target with the dimensions of the official
ISSF target. But unlike the latter, with the secondary
score in one hundredth rings instead of the one
tenth ring score of the ISSF.
09.08.2010
SIUS AG (c) 2004
06000019000207(44)
2 / 112
Targets\10m\Switzerland
Volkscheibe
A10 air rifle target with large 10-er ring for public
events.
06000019000209(38)
Running Target
The target pictures for the running target are filed in this directory. The discipline is also supported in the 10 metres by
the ISSF.
Standard
10 metre running target; ISSF Rules, Section
6.3.2.7.2; diameter 50.5mm; black reflector from ring 06000019001200(72)
5 to 10
Final
10 metre running target; ISSF Rules, Section
6.3.2.7.2; diameter 50.5mm; black reflector from ring 06000019001201(69)
5 to 10
Biathlon
The target pictures for biathlon are filed in this directory. Biathlon targets can be found under 10 metres and 50 metres.
15
Target image with 15 millimetre circle.
06000019001302(57)
20
Target image with 20 millimetre circle.
06000019001301(60)
09.08.2010
SIUS AG (c) 2004
3 / 112
Targets\10m\Biathlon
35
Target image with 35 millimetre circle.
06000019001300(63)
Other
Zimmerstutzen
German target
06000019000210(35)
Croatian AR Target
06000019000211(32)
25m
The directory 25m is the compilation of all target images which typically are used over a distance of 25 metres.
ISSF
Official targets of the ISSF are filed in this directory.
Precision
25 / 50 metre precision pistol target PP10; ISSF
Rules, Section 6.3.2.5, Diameter 500mm; black
reflector from ring 7 to ring 10
06000019000303(47)
Rapid Fire
25 metre rapid fire target, ISSF Rules, Section
6.3.2.4, Diameter 500mm; black reflector from ring 5
to 10
06000019000305(41)
Switzerland
Targets that are used only in Switzerland are stored in this directory.
09.08.2010
SIUS AG (c) 2004
4 / 112
Targets\25m\Switzerland
O10
Swiss ordnance rapid fire pistol target (military);
outline with ovals; Form 34.17
06000019000407(26)
Big bore pistol
Many 25 metre targets are also shot with large calibre pistols (9.65mm). In order that the calibre setting can be correctly
selected, these targets are listed twice.
Precision
25 / 50 metre precision pistol target PP10; ISSF
Rules, Section 6.3.2.5, Diameter 500mm; black
reflector from ring 7 to ring 10
06000019000311(23)
Rapid Fire
25 metre rapid fire target, ISSF Rules, Section
6.3.2.4, Diameter 500mm; black reflector from ring 5
to 10
06000019000313(17)
O10
Swiss ordnance rapid fire pistol target (military);
outline with ovals; Form 34.17
06000019000707(96)
50m
The directory 50m is the compilation of all target images which typically are used over a distance of 50 metres.
ISSF
Official targets of the ISSF are filed in this directory.
Rifle
50 metre precision rifle target; ISSF Rules, Section
6.3.2.2; diameter 154.4mm; black reflector from one
section of ring 3 to ring 10, diameter 112.4mm
09.08.2010
SIUS AG (c) 2004
06000019000301(53)
5 / 112
Targets\50m\ISSF
Final
06000019000302(50)
Pistol
25 / 50 metre precision pistol target PP10; ISSF
Rules, Section 6.3.2.5, Diameter 500mm; black
reflector from ring 7 to ring 10
06000019000303(47)
Switzerland
Targets that are used only in Switzerland are stored in this directory.
Rifle
A5
50 metre small calibre rifle target with five rings;
diameter 154.4mm; black reflector from one section
of ring 2 to ring 5.
06000019000307(35)
A10
50 metre precision rifle target; ISSF Rules, Section
6.3.2.2; diameter 154.4mm; black reflector from one
section of ring 3 to ring 10, diameter 112.4mm
06000019000308(32)
A20
50 metre precision rifle target; diameter 154.4mm;
black reflector from one section of ring 6 to 20,
diameter 112.4mm
09.08.2010
SIUS AG (c) 2004
06000019000309(29)
6 / 112
Targets\50m\Switzerland
A100
50 metre precision rifle target with a one hundred
ring score instead of the ISS ten ring score;
diameter 154.4mm; black reflector diameter
112.4mm
06000019000310(26)
Small Bore
Swiss pistol targets with small calibre (5.6mm) setting.
PA4
Pistol target A40; circular target with four rings.
06000019000401(44)
PA10
Pistol target A10; circular target with ten rings.
06000019000402(41)
PA100
Pistol target A100; circular target with one hundred
rings.
06000019000403(38)
PB5
Pistol target B5; circular target with five equal rings
and an outline whereby the outline is worth at least
three points.
06000019000404(35)
PB10
Pistol target B10; circular target with ten equal rings
and an outline.
09.08.2010
SIUS AG (c) 2004
06000019000405(32)
7 / 112
Targets\50m\Switzerland
PB100
Pistol target B100; circular target with one hundred
equal rings and an outline.
06000019000406(29)
O10
Swiss ordnance rapid fire pistol target (military);
outline with ovals; Form 34.17
06000019000407(26)
Big Bore
Big bore pistol
PA4
Pistol target A40; circular target with four rings.
06000019000701(17)
PA10
Pistol target A10; circular target with ten rings.
06000019000702(14)
PA100
Pistol target A100; circular target with one hundred
rings.
06000019000703(11)
PB5
Pistol target B5; circular target with five equal rings
and an outline whereby the outline is worth at least
three points.
09.08.2010
SIUS AG (c) 2004
06000019000704(08)
8 / 112
Targets\50m\Switzerland
PB10
Pistol target B10; circular target with ten equal rings
and an outline.
06000019000705(05)
PB100
Pistol target B100; circular target with one hundred
equal rings and an outline.
06000019000706(02)
O10
Swiss ordnance rapid fire pistol target (military);
outline with ovals; Form 34.17
06000019000707(96)
Morgarten
Outline target with five scores, whereby the value
two is assigned to five ellipses and the value one to
the rest of the outline.
06000019000410(17)
Biathlon
The target pictures for biathlon are filed in this directory. Biathlon targets can be found under 10 metres and 50 metres.
35mm
Target image with 35 millimetre circle.
06000019001306(45)
45mm
Target image with 45 millimetre circle.
06000019001305(48)
09.08.2010
SIUS AG (c) 2004
9 / 112
Targets\50m\Biathlon
85mm
Target image with 85 millimetre circle.
06000019001304(51)
110
Target image with 110 millimetre circle.
06000019001303(54)
300m
The directory 300m is the compilation of all target images which typically are used over a distance of 300 metres.
ISSF
Official targets of the ISSF are filed in this directory.
A10
06000019000002(77)
CISM
The A10 target which is used in military contests does not differ from the A10 target which is used in ISSF disciplines. So
that the filter function can be better used, the category CISM was separately introduced.
A10
06000019000002(77)
Switzerland
Targets that are used only in Switzerland are stored in this directory.
A
A-targets with varied scores:
A5
06000019000001(80)
09.08.2010
SIUS AG (c) 2004
10 / 112
Targets\300m\Switzerland
A6
06000019000005(68)
A10
06000019000002(77)
A100
06000019000003(74)
A10/FA10
06000019000014(41)
A10 final
06000019000015(38)
B
B-targets with different scores (field target B Form. 34.21.2.88):
B4
06000019000004(71)
09.08.2010
SIUS AG (c) 2004
11 / 112
Targets\300m\Switzerland
B10
06000019000008(59)
B100
06000019000009(56)
PB5
Pistol target PB5
06000019000010(53)
F5
06000019000007(62)
Scandinavia
Targets that are used only in Scandinavia are stored in this directory. The exception is animal images (moose and
reindeer) which can be found under '\Other\Hunting\Moose'.
Norway
Nor7
06000019001101(78)
Nor8
06000019001102(75)
09.08.2010
SIUS AG (c) 2004
12 / 112
Targets\300m\Scandinavia
NSF 15m
06000019001410(24)
DFS 15m
06000019001411(21)
DFS100
06000019001103(72)
DFS 200
06000019001412(18)
DFS 300
06000019001413(15)
New Swedish target
06000019001100(81)
16FIG
06000019001105(66)
09.08.2010
SIUS AG (c) 2004
13 / 112
Targets\300m\Scandinavia
16V
06000019001106(63)
C30
06000019001104(69)
A10 Reduced 200
06000019001414(12)
Belgium
Targets from Belgium
A10
06000019000002(77)
Oly100
Oly100 Target
06000019001501(42)
Oly200
Oly200 Target
06000019001502(39)
09.08.2010
SIUS AG (c) 2004
14 / 112
Targets\300m\Belgium
Schijf K
Schijf K Target
06000019001503(36)
Schijf 4
Schijf 4 Target
06000019001504(33)
Schijf 5
Schijf 5 Target
06000019001505(30)
Schijf S
Schijf S Target
06000019001506(27)
NTTC4
06000019001507(24)
NTTC5
06000019001508(21)
Other
All targets that do not clearly fall under one of the preceding distances are included in the category 'Other'.
Italy
09.08.2010
SIUS AG (c) 2004
15 / 112
Targets\Other\Italy
Bersaglio 1
06000019002400(61)
Bersaglio 2
06000019002401(58)
Bersaglio 9
06000019002402(55)
P1
06000019002403(52)
P2
06000019002404(49)
P3
06000019002405(46)
A10 100m
06000019002406(43)
09.08.2010
SIUS AG (c) 2004
16 / 112
Targets\Other\Italy
A10 200m
06000019002407(40)
A10 300m
06000019002408(37)
Austria
ASR
\ASR\Pistol
Pistol A 5m
06000019001700(27)
Pistol A 10m
06000019001701(24)
Pistol B 5m
06000019001702(21)
Pistol B 10m
06000019001703(18)
09.08.2010
SIUS AG (c) 2004
17 / 112
Targets\Other\Austria
Pistol D 5m
06000019001704(15)
Pistol D 10m
06000019001705(12)
Pistol C 7m
06000019001706(09)
Pistol C 15m
06000019001707(06)
Pistol C All
06000019001708(03)
Pistol E 20m
06000019001709(97)
Pistol E All
06000019001710(94)
09.08.2010
SIUS AG (c) 2004
18 / 112
Targets\Other\Austria
\ASR\Rifle
Rifle A 10m vertical
06000019001602(30)
Rifle A 20m vertical
06000019001603(27)
Rifle B 10m horizontal
06000019001604(24)
Rifle B 20m horizontal
06000019001605(21)
Rifle B 10m ellipse
06000019001606(18)
Rifle B 20m ellipse
06000019001607(15)
09.08.2010
SIUS AG (c) 2004
19 / 112
Targets\Other\Austria
Rifle C 15m
06000019001608(12)
Rifle C 30m
06000019001609(09)
Rifle C All
06000019001610(06)
Rifle D 40m
06000019001611(03)
Rifle D All
06000019001612(97)
Classic
\Classic\Pistol
A10
06000019001810(85)
09.08.2010
SIUS AG (c) 2004
20 / 112
Targets\Other\Austria
A100
06000019001811(82)
Klein links
06000019001801(15)
Klein rechts
06000019001802(12)
Gross links
06000019001803(09)
Gross rechts
06000019001804(06)
Klein Klein
06000019001805(03)
Klein Gross
06000019001806(97)
09.08.2010
SIUS AG (c) 2004
21 / 112
Targets\Other\Austria
Gross Klein
06000019001807(94)
Gross Gross
06000019001808(91)
Precision
25 / 50 metre precision pistol target PP10; ISSF
Rules, Section 6.3.2.5, Diameter 500mm; black
reflector from ring 7 to ring 10
06000019001812(79)
\Classic\Rifle
R10
06000019001800(18)
A10
06000019000002(77)
A100
06000019000003(74)
09.08.2010
SIUS AG (c) 2004
22 / 112
Targets\Other\Austria
Anschuss Scheibe
06000019001809(88)
\Classic\MG
\Classic\MG\A
MG Ziel A1
06000019001900(09)
MG Ziel A2
06000019001901(06)
MG Ziel A3
06000019001902(03)
MG Ziel A4
06000019001903(97)
MG Ziel A5
06000019001904(94)
09.08.2010
SIUS AG (c) 2004
23 / 112
Targets\Other\Austria
MG Ziel A6
06000019001905(91)
MG Ziel A7
06000019001906(88)
MG Ziel A8
06000019001907(85)
\Classic\MG\B
MG Ziel B1
06000019001908(82)
MG Ziel B2
06000019001909(79)
MG Ziel B3
06000019001910(76)
09.08.2010
SIUS AG (c) 2004
24 / 112
Targets\Other\Austria
MG Ziel B4
06000019001911(73)
MG Ziel B5
06000019001912(70)
MG Ziel B6
06000019001913(67)
MG Ziel B7
06000019001914(64)
MG Ziel B8
06000019001915(61)
\Classic\MG\C
MG Ziel C1
06000019002000(97)
09.08.2010
SIUS AG (c) 2004
25 / 112
Targets\Other\Austria
MG Ziel C2
06000019002001(94)
MG Ziel C3
06000019002002(91)
MG Ziel C4
06000019002003(88)
MG Ziel C5
06000019002004(85)
MG Ziel C6
06000019002005(82)
MG Ziel C7
06000019002006(79)
MG Ziel C8
06000019002007(76)
09.08.2010
SIUS AG (c) 2004
26 / 112
Targets\Other\Hunting
Hunting
Moose
Summary of the moose targets:
\Moose\Left
Moose 5-5-4-3
Moose target with the scores 5-5-4-3 and 10-8-6-4.
06000019001401(51)
Moose
Moose target with tenner score.
06000019001404(42)
Moose SWE
Swedish moose target with 5-5-4-3 score.
06000019001407(33)
Moose Calf
Swedish Elkcalf target with 5-5-4-3 and Hit-Score
06000019001409(27)
\Moose\Right
Moose 5-5-4-3
Moose target with the scores 5-5-4-3 and 10-8-6-4.
06000019001402(48)
09.08.2010
SIUS AG (c) 2004
27 / 112
Targets\Other\Hunting
Moose
Moose target with tenner score.
06000019001405(39)
Moose SWE
Swedish moose target with 5-5-4-3 score.
06000019001408(30)
Moose Calf
Swedish Elkcalf target with 5-5-4-3 and Hit-Score
06000019001415(09)
\Moose\Double
Moose 5-5-4-3
Moose target with the scores 5-5-4-3 and 10-8-6-4.
06000019001400(54)
Moose
Moose target with tenner score.
06000019001403(45)
Moose SWE
Swedish moose target with 5-5-4-3 score.
06000019001406(36)
Boar
Summary of bore targets:
09.08.2010
SIUS AG (c) 2004
28 / 112
Targets\Other\Hunting
Wild Boar 5
Running target 50 metre (ISSF-Bore 5; DJV No. 5);
ISSF Rules Section 6.3.2.7.1
Diameter 60mm
06000019000110(44)
Wild Boar 5 Right
Running target 50 metre (ISSF-Bore 5; DJV No. 5);
ISSF Rules Section 6.3.2.7.1
Diameter 60mm
06000019000104(62)
Wild Boar 2
DJV Number 2; Bore Art. No. S100AA010V1
06000019001514(03)
Bear
Bear Target
Bear Left
06000019001213(33)
Bear Right
06000019001214(30)
Bear
06000019001215(27)
Other
Bear Target
09.08.2010
SIUS AG (c) 2004
29 / 112
Targets\Other\Hunting
Kronhjort
06000019002500(52)
Roebuck left
06000019002501(49)
Roebuck right
06000019002502(46)
Chamois
DJV Number 1; Chamois Art. No. S100AA008V1
06000019000108(50)
Fox
DJV Number 2; Fox Art. No. S100AA009V1
06000019000106(56)
Roe
DJV Number 4; Roebuck Art. No. S100AA007V1
06000019000102(68)
09.08.2010
SIUS AG (c) 2004
30 / 112
Targets\Other\Hunting
Danish Roebuck
06000019000115(29)
Reindeer
Reindeer DV-! Norway; Art. No. S100AA012
06000019000114(32)
Roe Left
Hubertus Reh linkslaufend (Spezialscheibe für
Kanton St. Gallen)
06000019000112(38)
Chamois Hubertus
Hubertus Gams rechtslaufend (Spezialscheibe für
Kanton St. Gallen)
06000019000113(35)
Precision
25 / 50 metre precision pistol target PP10; ISSF
Rules, Section 6.3.2.5, Diameter 500mm; black
reflector from ring 7 to ring 10
06000019000303(47)
Scandinavia
Targets that are used only in Scandinavia are stored in this directory. The exception is animal images (moose and
reindeer) which can be found under '\Other\Hunting\Moose'.
Military
09.08.2010
SIUS AG (c) 2004
31 / 112
Targets\Other\Scandinavia
2x1/3 figure
06000019001112(45)
1/1+1/3 figure
06000019001113(42)
Full Figure
06000019001107(60)
1/8+1/2 figure
06000019001114(39)
Half Figure
06000019001108(57)
One Third Figure
06000019001109(54)
Eighth figure
06000019001110(51)
09.08.2010
SIUS AG (c) 2004
32 / 112
Targets\Other\Scandinavia
Precision
06000019001115(36)
Full Bore
300y
06000019002300(70)
500y
06000019002301(67)
600y
06000019002302(64)
300m
06000019002303(61)
500m
06000019002304(58)
09.08.2010
SIUS AG (c) 2004
33 / 112
Targets\Other\Full Bore
600m
06000019002305(55)
Long Range
06000019002306(52)
Norway
B
B45
06000019002210(49)
B65
06000019002211(46)
B100
06000019002212(43)
Smaen
06000019002213(40)
09.08.2010
SIUS AG (c) 2004
34 / 112
Targets\Other\Norway
Minismaen
06000019002214(37)
C
C15
06000019002100(88)
C20
06000019002101(85)
C25
06000019002102(82)
C30
06000019002103(79)
C35
06000019002104(76)
09.08.2010
SIUS AG (c) 2004
35 / 112
Targets\Other\Norway
C40
06000019002105(73)
C50
06000019002106(70)
1/x
1/3Mini
06000019002200(79)
1/3
06000019002202(73)
1/4Mini
06000019002201(76)
1/4Figur
06000019002207(58)
09.08.2010
SIUS AG (c) 2004
36 / 112
Targets\Other\Norway
1/4
06000019002203(70)
1/6
06000019002204(67)
1/8
06000019002205(64)
1/10
06000019002206(61)
Other
13x40
06000019002107(67)
30x10
06000019002108(64)
09.08.2010
SIUS AG (c) 2004
37 / 112
Targets\Other\Norway
Stripe
06000019002109(61)
Prisme
06000019002110(58)
S25
06000019002111(55)
Hjul
06000019002112(52)
150Sirkel
06000019002113(49)
55Sirkel
06000019002114(46)
40Tonne
06000019002208(55)
09.08.2010
SIUS AG (c) 2004
38 / 112
Targets\Other\Norway
14Tonne
06000019002209(52)
09.08.2010
SIUS AG (c) 2004
39 / 112
Programs
Programs
The programs are subdivided according to the usual distance, and according to categories of additional properties (e.g. Federation
programs, group championships). The individual programs are designated with the target picture (e.g. A5), the type or fire (T=Test
shots, S=Single fire, D=Serial fire) and the number of shots in this type of fire (T2 = 2 test shots, S5 = single fire 5 shots, D3 = serial
fire 3 shots, T0 = test free/open, i.e. an open-ended number of test shots can be fired).
10m
The directory 10m is the compilation of all programs which typically are shot over a distance of 10 metres.
ISSF
Air Rifle 40
20000735(55)
Air Rifle 60
20000734(58)
Air Pistol 40
20000737(49)
Air Pistol 60
20000736(52)
Running Target
3030
20000760(77)
2020
20000761(74)
Mixed
20000762(71)
Biathlon
15mm
06000019001302(57)
20mm
06000019001301(60)
Pentathlon
09.08.2010
SIUS AG (c) 2004
40 / 112
Programs\10m\Pentathlon
Pentathlon 20
20000450(37)
Pentathlon 3*10
20000460(07)
CE
20000451(34)
Sighters
20000452(31)
Other
Air Rifle 30
20000756(89)
Air Rifle 20
20000757(86)
Air Rifle 3*10
20000754(95)
Air Pistol 20
20000739(43)
Zimmerstutzen 30
20000748(16)
Rapid Fire Pistol
20000765(62)
25m
The directory 25m is the compilation of all programs which typically are shot over a distance of 25 metres.
ISSF
Rapid Fire Pistol
20000730(70)
Sport Pistol
20000733(61)
Center Fire Pistol
20000731(67)
Standard Pistol
20000732(64)
CISM
Sport Pistol
20000733(61)
09.08.2010
SIUS AG (c) 2004
41 / 112
Programs\25m\CISM
Center Fire Pistol
20000731(67)
Military Rapid Fire Men
20000750(10)
Military Rapid Fire Women
20000753(01)
Sui
OP
20000830(61)
FS
20000831(58)
Other
SP15
20000751(07)
50m
The directory 50m is the compilation of all programs which typically are shot over a distance of 50 metres.
ISSF
Rifle 60
20000725(85)
Standard Rifle 3*20
20000726(82)
Free Rifle 3*40
20000724(88)
Pistol 60
20000727(79)
CISM
Rifle 60
20000725(85)
Standard Rifle 3*20
20000726(82)
Biathlon
09.08.2010
SIUS AG (c) 2004
42 / 112
Programs\50m\Biathlon
35mm
06000019001306(45)
45mm
06000019001305(48)
85mm
06000019001304(51)
110
06000019001303(54)
Running Target
ISSF
3030
20000770(47)
2020
20000771(44)
Mixed
20000772(41)
DJV
Wild Boar 5
20000775(32)
SWE
09.08.2010
SIUS AG (c) 2004
43 / 112
Programs\50m\Running Target
Running Roebuck
20000851(95)
Running Moose
20000852(92)
Sui
OP
20000832(55)
FS
20000833(52)
Morgarten
20000361(13)
PB5
D4D6
20000072(07)
Other
Rifle 3*10
20000755(92)
Rifle 30
20000758(83)
300m
The directory 300m is the compilation of all programs which typically are shot over a distance of 300 metres.
ISSF
Free Rifle 3*40
20000721(97)
Free Rifle 60
20000722(94)
Standard Rifle 3*20
20000723(91)
Rifle 2x30
20000717(12)
CISM
Standard Rifle 3*20
20000723(91)
09.08.2010
SIUS AG (c) 2004
44 / 112
Programs\300m\CISM
Rapid Fire 3x20
Military Rapid Fire 3*20
20000816(06)
Switzerland
OP
Complete
20000840(31)
OP A5 Sighters
20000839(34)
OP Part 1
A5 S5
20000838(37)
OP B4 Sighters
20000836(43)
OP Part 2
B4 S5 D2 D3 D5
20000837(40)
Group championship
A5P
Unlimited test shots feature on the A5 window
20000398(96)
A10P
Unlimited test shots feature on the A10 window
20000397(02)
Field A
GM Field A
20000084(68)
Field B
GM Field B
20000014(84)
Field D
GM Field D
20000083(71)
A
\A\A5
\A\A5\Shot by Shot
S0
20011011(73)
S4
20000019(69)
09.08.2010
SIUS AG (c) 2004
45 / 112
Programs\300m\Switzerland
S5
20000012(90)
S6
20000013(87)
S8
20000020(66)
S10
20000015(81)
\A\A5\Deferred
D0
20000010(96)
D5
20000023(57)
D6
20000024(54)
D3D3
20000025(51)
D4D4
20000026(48)
D5D5
20000016(78)
\A\A5\Deferred\Include sighters
P2 D2 D3 D5
20000344(64)
P1 D2 D3 D4 D5
20000346(58)
P2 D2 D2 D3 D3
20000348(52)
\A\A5\Combined
S4D4
20000006(11)
S5D3
20000021(63)
09.08.2010
SIUS AG (c) 2004
46 / 112
Programs\300m\Switzerland
S2 D3 D5
20000009(02)
S4 D3 D3
20000022(60)
S5 D3 D4
20000007(08)
S6 D3 D3
20000676(38)
S2 D2 D3 D5
20000008(05)
\A\A5\Combined\Include sighters
S6D4
20000002(23)
P2 S1 D3 D6
20000027(45)
P2 S2 D3 D3
20000668(62)
P2 S2 D3 D5
20000003(20)
P2 S5 D3 D4
20000667(65)
P3 S6 D3 D3
20000001(26)
P2 D2 D2 D3 D3
20000005(14)
P1 S2 S3 S4 S5
20000004(17)
\A\A10
\A\A10\Shot by Shot
S0
20000031(33)
S5
20000033(27)
09.08.2010
SIUS AG (c) 2004
47 / 112
Programs\300m\Switzerland
S6
20000034(24)
S8
20000035(21)
\A\A10\Shot by Shot\Include sighters
Opening shooting
20000763(68)
P2S6
20000666(68)
S10
20000029(39)
S6S4
20000038(12)
\A\A10\Deferred
D0
20000030(36)
D5
20000043(94)
D6
20000044(91)
D3D3
20000045(88)
\A\A10\Deferred\Include sighters
P2D1
20000694(81)
P2 D2 D3 D5
20000040(06)
P2 4*D5
20000028(42)
\A\A10\Combined
S3D3
20000041(03)
S4D4
20000042(97)
09.08.2010
SIUS AG (c) 2004
48 / 112
Programs\300m\Switzerland
S5D3
20000046(85)
S6D4
20000032(30)
S2 D3 D5
20000039(09)
S2 D3 D5
20000357(25)
S4 D3 D3
20000210(78)
S3 S4 D4 D4
20000677(35)
\A\A10\Combined\Include sighters
S4D4
20000047(82)
S5D3
20000037(15)
S6D6
20000048(79)
P2 S5 D2 D3
20000356(28)
P2 4*D5
20000695(78)
Prone 4*S10
20000589(08)
Standing 4*S10
20000579(38)
Kneeling 4*S10
20000569(68)
\A\A100
P0
20000396(05)
\A\A100\Shot by Shot
09.08.2010
SIUS AG (c) 2004
49 / 112
Programs\300m\Switzerland
S0
20000051(70)
S2
Nachdoppel
20000052(67)
S3
20000053(64)
S4
20000054(61)
S5
20000055(58)
S6
20000056(55)
S10
20000057(52)
P1S4
20000665(71)
D0
20000050(73)
D4D4
20000049(76)
P2 S5 D2 D3
20000058(49)
B
\B\B4
P0
20000395(08)
\B\B4\Shot by Shot
S0
20000061(40)
S6
20000062(37)
\B\B4\Deferred
D0
20000060(43)
09.08.2010
SIUS AG (c) 2004
50 / 112
Programs\300m\Switzerland
D5
20000064(31)
D6
20000063(34)
D3D3
20000065(28)
D4D4
20000066(25)
P2 D4 D6 KOM
20000349(49)
\B\B4\Combined
S3 D3 D3
20000067(22)
S3 D3 D6
20000379(56)
S3 D3 D3 D3
20000069(16)
S4D4
20000345(61)
S6 D3 D3 D6 KOM
20000359(19)
\B\B4\Combined\Include sighters
P2 S1 S3 S6
20000068(19)
P2 S2 D3 D5
20000669(59)
S4D4
20000070(13)
P2 S6 D6 D6
20000075(95)
\B\B10
P0
20000968(35)
09.08.2010
SIUS AG (c) 2004
51 / 112
Programs\300m\Switzerland
S0
20000076(92)
D0
20000077(89)
S2 D3 D5
20000376(65)
S2D2
20000078(86)
D3D5
20000079(83)
\B\B100
P0
20000967(38)
S0
20000081(77)
D0
20000080(80)
S10
20000082(74)
\B\PB5
P0
20000394(11)
S0
20000071(10)
D0
20000073(04)
D4D6
20000072(07)
Other
FS
20000059(46)
Knabenschiessen
The youth shooting practice is solely for the Zurich
Youth Shoot. Therefore it has a special score (A6)
20000399(93)
and a special printout. In youth shooting 5 shots are
fired at an A5 target. The innermost ring (5-er ring) is
valued with 6 points. The outermost ring counts for 2
09.08.2010
SIUS AG (c) 2004
52 / 112
Programs\300m\Switzerland
points instead of 1 point. Each hit outside the
outermost ring that nonetheless hits the target
counts for 1 point. Moreover at the end each target
hit is further awarded 1 point and this sum is
included in the total result. The maximum is
therefore 5 x 6 points + 5 hits = 35 points.
Morgarten
20000362(10)
Pfäffiker winter practice
Hit score for single firer: every 10 shots in 10-er
score; for group score 2. Pass (E4) in 100-er score.
20000377(62)
Ustertag-Scheibe
20000738(46)
Vögelinsegg
20000363(07)
Hans Waldmann Schiessen
20000776(29)
F5
D0
20000976(11)
S0
20000986(78)
Scandinavia
Swedish program
Double
P0 S5 S5 S5 S5
20000718(09)
10
P0 S5 S5
20000719(06)
25
P0 S5 S5 S5 S5 S5
20000720(03)
Swedish championship
First relay
P0 S5 S5 S5
20000705(48)
Middle relay
P0 S5 S5
20000706(45)
Final
P0 S5 S5
20000707(42)
09.08.2010
SIUS AG (c) 2004
53 / 112
Programs\300m\Scandinavia
Reserved
P0 S5 S5 S5 S5
20000708(39)
Final reserved
P0 S5 S5 S5
20000709(36)
Other
Rifle 3*10
20000728(76)
Other
All targets that do not clearly fall under one of the preceding distances are included in the category 'Other'.
Full Bore
3yDL
20000860(68)
5yDL
20000861(65)
6yDL
20000862(62)
LRDL
20000863(59)
Austria
Pistol
\Pistol\1
1
Pistol A 5m
20000500(81)
Pistol A 10m
20000501(78)
\Pistol\2
2
Pistol B 5m
20000502(75)
Pistol B 10m
20000503(72)
\Pistol\3
3
09.08.2010
SIUS AG (c) 2004
54 / 112
Programs\Other\Austria
Pistol D 5m
20000504(69)
Pistol D 10m
20000505(66)
\Pistol\4
4
Pistol D 5m
20000504(69)
Pistol D 10m
20000505(66)
5
5
20000504(69)
6
6
20000504(69)
7
7
20000506(63)
8
8
20000508(57)
9
9
20000508(57)
10
10
20000507(60)
11
11
20000509(54)
12
12
20000510(51)
Rifle
\Rifle\5
5
Rifle A 10m vertical
20000511(48)
Rifle A 20m vertical
20000512(45)
\Rifle\6
6
09.08.2010
SIUS AG (c) 2004
55 / 112
Programs\Other\Austria
Rifle B 10m horizontal
20000513(42)
Rifle B 20m horizontal
20000514(39)
\Rifle\7
7
Rifle B 10m ellipse
20000515(36)
Rifle B 20m ellipse
20000516(33)
\Rifle\8
8
Rifle B 10m ellipse
20000515(36)
Rifle B 20m ellipse
20000516(33)
9
9
20000515(36)
10
10
20000515(36)
11
11
20000515(36)
12
12
20000519(24)
13
13
20000519(24)
\Rifle\14
14
Rifle C 15m
20000517(30)
Rifle C 30m
20000518(27)
15
15
20000520(21)
16
16
20000521(18)
09.08.2010
SIUS AG (c) 2004
56 / 112
Programs\Other\Scandinavia
Scandinavia
Targets that are used only in Scandinavia are stored in this directory. The exception is animal images (moose and
reindeer) which can be found under '\Other\Hunting\Moose'.
Military
2x1/3 figure
20000740(40)
1/1+1/3 figure
20000741(37)
Full Figure
20000742(34)
1/8+1/2 figure
20000743(31)
Half Figure
20000744(28)
One Third Figure
20000745(25)
Eighth figure
20000746(22)
Precision
20000747(19)
Hunting
Moose
20000850(01)
Moose LR Running
20000853(89)
09.08.2010
SIUS AG (c) 2004
57 / 112
Control
Control
The control menu contains all the functions that are necessary during a running program. The menu pops up automatically into this
view after a program is selected.
Zoom
Most target pictures can be represented in three
different sizes (zoom levels). The zoom command
switches to the next size. When the smallest size
has been reached, then the next zoom command
brings up the largest size again.
099052(52)
Match
In the course of a match, by means of the Match
button (RC92) the major commands for controlling
the match can be carried out by the firer. Thus the
setting can be changed from the test group to the
first single group. So long as the single group has
not yet shot, triggering this command again can
enable a return to the test group. In user practices
and in free series this command does not appear in
the menu. In this case (if the RC92 is pressed or if
the corresponding barcode is input) a group total is
triggered.
990636(75)
Sighters
In free series the fire type can be restarted at any
time with the commands Test, Single and Series.
99063400(49)
Shot by Shot
In free series the fire type can be restarted at any
time with the commands Test, Single and Series. If
the fire type is already set to single, with this
command the single group can be totalised and
immediately a new group can be started. In this way
for example every 10 shots a group total of an ISSF
shoot can be simulated.
99063401(46)
Subtotal
Closes off the current open group and prints out a
group total. The function is available only when an
open group (P-, S- or D-) is shot. A group where the
number of shots is prescribed cannot be skipped. If
shooting takes place without a shot logoff, then
shots which have totally missed the target must be
reported to the system with the command
'\Other\Insert zero shot'.
990530(05)
Total
In a free series the group total corresponds to the
intermediate total or to a position total. The current
group is added up. This corresponds to a subtotal.
In addition all the groups since the last group total
are counted together and removed. Thereafter the
group can be continued.
990531(02)
TOTAL
In a free series the match total stops the current
program (program total). It triggers a subtotal and a
group total. In addition all shot values (except test
shots) are added together and shown as the 'large'
total. Other programs than the free series (match,
user practice and fixed programs) cannot be
stopped prematurely. They can only be broken off
09.08.2010
SIUS AG (c) 2004
990532(96)
58 / 112
Control\TOTAL
and filled with manual nulls. An abort can be brought
about by the command '\Other\Abort' or by loading
another program. In the event of an abort the shot
values are also added together and displayed.
Deferred
In free series the fire type can be restarted at any
time with the commands Test, Single and Series. If
the fire type is already set to Series, with this
command the series group can be shown and
totalised. Subsequently a new series group is
automatically started.
99063402(43)
Show
In a group with serial shots all shots fired up to the
present moment are displayed in advance.
099054(46)
Correspondingly at the end of the group, only those
shots which have not yet been displayed are shown.
In groups with the fire type Test or Single Shot the
barcode has no effect.
Score
In free series the command Value can change the
secondary score to the primary score. This is useful 990643(54)
if first a qualifier and then a final are shot. At most
official shoots the finals are scored in tenths, but the
qualifiers are scored in whole tens. If the command
is carried out a second time, then the original score
is switched on again. With the commands
'\Other\Next Primary Score' and '\Other\Next
Secondary Score' the primary and secondary scores
can be controlled.
Print screen
The current screen content is printed on the graphic
printer (Only D931/CBM210). It is not possible to
print out on the dot matrix printer D93.
099050(58)
Repeat
Restarts a closed off practice with the same settings
(firer number, firer name, weapon and position). This 91(18)
command can be blocked with the setting
'\Other\Start\Permit Repeat\(Off)'.
SC-Programs
Practice
In programs that show a match structure, under 'Group' it is possible to select which setting you want to begin with. In this way
for example only the final of a match can be shot. During the match in progress, under 'Group' the setting 'Test' can be
selected. This test corresponds to the regulated exceptional test which can be permitted after weapon malfunction. If the
setting 'Test' is selected, then under 'Group' only the position that was shot most recently appears. Choosing this position
enables you to return to the official match.
Malfunction
In the 25m pistol disciplines, various rules are defined which lay down the procedures for weapon failures. According to the
discipline and the type of weapon failure (allowable / non allowable) the fired shots must be completed and evaluated.
Individual commands enable the system to correctly calculate the end result and to correctly show the individual shots on the
screen as well as on the scoreboard.
Fill Series
The active group is stocked with zeros. This also
happens when the group have not yet shot.
09.08.2010
SIUS AG (c) 2004
99063700(22)
59 / 112
Control\Malfunction\Insert zero shot
Insert zero shot
Inserts a shot with the value 0 into the current
program. This function is needed if shooting took
place without the use of the shot sensor and the
target was missed. The system itself cannot
recognise the shot in this situation.
099058(34)
Allowable
A permitted weapon malfunction (decision of the
referee) permits the firer to complete the group
according to the discipline (sport pistol, central fire
pistol in rapid fire section) or to repeat it (standard
pistol, rapid fire). The execution of this command
produces at least one log entry.
99063701(19)
Non-Allowable
Non allowable weapon failures normally result in the
open group being completed with zero and no repeat 99063702(16)
being available to the firer. Additionally a log entry is
produced.
Compute series
'Calculate series' completes the handling of weapon
malfunctions. Even when several repetitions have
had to be shot, on this command the shots are
correctly selected and counted according to the
rules of the ISSF.
99063703(13)
Other
Frequently used operating elements can be found directly under the Control menu\Other.
Abort
Produces in addition to the match total an abort (log
entry) in order to mark the current group as invalid.
50(44)
Insert zero shot
Inserts a shot with the value 0 into the current
program. This function is needed if shooting took
place without the use of the shot sensor and the
target was missed. The system itself cannot
recognise the shot in this situation.
099058(34)
Clear target window
Clears the shots from the target window without
removing them from the score. (see also the setting
'Clear target window after shots')
099062(22)
Clear List
Clears all entries from the list window, without
removing the fired shots from the score.
990630(93)
Convert last sighting shot
09906901(97)
Convert both sighters
09906902(94)
Timer
This commands are used to control the embedded Timer.
09.08.2010
SIUS AG (c) 2004
60 / 112
Control\Other\Timer
Set Timer
Sets the Timer to the entered value and displays it in
the titlebar
990650(33)
Start Timer
starts the timer
990651(30)
Reset Timer
Resets the timer to the value set by the Set Timer
command
990652(27)
Remove Timer
Disables the Timer and removes it from the Display
990653(24)
Fix timer values
Here is a collection of fix timer values to configure the timer via Barcode
30s
30s
9906600030(34)
40s
40s
9906600040(04)
50s
50s
9906600050(71)
60s
60s
9906600060(41)
90s
90s
9906600090(48)
300s
5 min
9906600300(97)
1h
1h
9906603600(91)
Next Primary Score
Every target image has a number of score methods
installed, which can be used to evaluate the target.
With the command '\Other\Next Primary Score'
these different score methods can be scrolled
through. These amendments can only be made for
free series. It should also be observed that different
score methods are not strongly compatible one with
another. It is therefore not advisable to change the
score method while a program is running.
9906421999(45)
Next Secondary Score
Just as for the primary score, so too can the score
method for the secondary score be changed.
9906422999(52)
Edit Barcode
990646(45)
09.08.2010
SIUS AG (c) 2004
61 / 112
System
System
Settings and commands that in normal shooting operation must rarely be changed or used. Some of the functions available are also
reserved for specific user groups (administrator and Sius staff).
Reports
With many reports information about past programs can be printed out.
Reload
The last ten groups can subsequently be loaded once more and considered with the discussion mode. However in a
subsequently loaded group no further amendments can be carried out. The shot picture can in this way once again also
be created from completed programs and displayed.
1
Load the last program that was shot in order that it
can be discussed.
99063800(13)
2
Load the program before last in order that it can be
discussed.
99063801(10)
3
Load the third from last program in order that it can
be discussed.
99063802(07)
4
Load the fourth from last program in order that it can
be discussed.
99063803(04)
5
Load the fifth from last program in order that it can
be discussed.
99063804(01)
6
Load the sixth from last program in order that it can
be discussed.
99063805(95)
7
Load the seventh from last program in order that it
can be discussed.
99063806(92)
8
Load the eighth from last program in order that it can
be discussed.
99063807(89)
9
Load the ninth from last program in order that it can
be discussed.
99063808(86)
10
Load the tenth from last program in order that it can
be discussed.
99063809(83)
Reprint
In the event of a paper jam or other printer problem it can happen that a score sheet does not print out as desired.
Finished groups can therefore be repeatedly printed out.
1
Print out the last program again.
09905520(69)
09.08.2010
SIUS AG (c) 2004
62 / 112
System\Reports\Reprint
2
Print out the program before last again.
09905521(66)
3
Print out the third from last program again.
09905522(63)
4
Print out the fourth from last program again.
09905523(60)
5
Print out the fifth from last program again.
09905524(57)
6
Print out the sixth from last program again.
09905525(54)
7
Print out the seventh from last program again.
09905526(51)
8
Print out the eighth from last program again.
09905527(48)
9
Print out the ninth from last program again.
09905528(45)
All
Reprint all programs remaining in the log.
09905529(42)
Shot Counter
Mechanical shot counters:
The optional mechanical shot counter only counts the shots on your own target. It cannot be reset. Demo shots or
inserted no scores are not counted. A detailed description of the whole function can be found in the user manual under
'Mechanical shot counters'.
Software shot counters:
The software shot counter counts shots in different categories. Own shots, cross shots, missed shots, demo shots etc.
are differentiated and displayed separately. The shot count report is displayed in the list window and provided a printer is
connected and switched on, is printed out. The shot counters are connected to the control units. If the settings are reset
to factory settings, the shot counts are also reset to zero. The same occurs when the battery has to be changed. With a
normal interruption to the power supply, the values are not lost. The software shot counters can also be reset
independently of the settings under '\Maintenance\Reports\Shot Counters'.
Report Shot Counter
The current shot numbers are displayed on the
screen and on the printer.
09903608(82)
Invalid shots
Non-allowable shots (shots during the Stop, Pause or the Show Phase and cross shots) are not only counted, they are
kept in the control unit as pending and can be queried at any time. The shots are then shown with the time and if
possible with the score. With a warm start or with the command 'Erase' under '\Maintenance\Invalid Shots' the report can
be rejected. The shots remain in the log throughout and furthermore can be documented in a log printout.
Show
The report on invalid shots is displayed in the list
window.
990562(06)
Print
The report on invalid shots is printed out on the
connected printer. If the printer is not turned on, the
report is rejected.
09.08.2010
SIUS AG (c) 2004
990564(97)
63 / 112
System\Reports\Invalid shots
Log
Events that are of relevance for the duration of a program are filed in the memory (events memory, log). This information
is needed to be able to reproduce a program after a power interruption. The CU931 investigates this data at every
system start-up. If it is established that the last program to be shot was not correctly ended, then a repetition process is
introduced. By means of the log past programs can also be reloaded or a copy can be printed once again. The log is
stored in the volatile memory of the control unit, which is buffered with a battery. The data is protected from
misinterpretation by a check sum. If the check sum is not correct at system start-up, for example due to a faulty battery,
the log is initialised again. The control unit communicates this by a triple beep and a report in the list window. The log is
restricted in memory size. In the event of an overload, the oldest events are overwritten by the most recent on a rolling
basis. Typically more than ten programs can be stored in the log. The log can also be manually erased under
'\Maintenance\Reports\Log'. The format of the printout is described in the user manual.
All
All events are printed out in chronological order. The
oldest events first, and the most recent events at the 09905500(32)
end. The printout can be broken off at any time by
switching off the printer.
10
The ten most recent events are printed out in
chronological order.
09905501(29)
20
The twenty most recent events are printed out in
chronological order.
09905502(26)
50
The fifty most recent events are printed out in
chronological order.
09905505(17)
Inverse
All events are printed out in reverse chronological
order, the most recent events first, and the oldest
events at the end. The printout can be broken off at
any time by switching off the printer.
09905509(05)
Settings
The performance of the control unit can be adapted to the user's own needs by means of very many different settings.
Programs can behave differently according to the properties selected. On the other hand, it is possible for fixed programs to
overwrite particular properties. So for example shots are printed out differently in ISSF programs to other programs. It is also
possible for programs to select a setting simply as a basic setting, which subsequently (after the program has been switched
on) can be changed again by the user. The printout of shots in ISSF disciplines can subsequently be changed again under
'Presentation\Shot\Standard\Print format'.
Presentation
All the settings that affect the images of objects in the wider sense are stored under 'Presentation'. This applies not only
to representation on the screen, but also to forms of representation on the printer and other display equipment.
Shot
The directory '\Presentation\Shot' contains settings which alter the appearance of the shots. This affects not only
the shot symbol but also the image in the shot window, in the list window and on the printer.
\Shot\Last Shot
In the directory '\Last shot' the settings which influence the depiction of the last represented shot are stored.
\Shot\Last Shot\Symbol
The symbol of a shot can be varied according to appearance, size and background.
\Shot\Last Shot\Symbol\Form
The form of the symbol can be preset individually for the last shot and jointly for all other shots.
09.08.2010
SIUS AG (c) 2004
64 / 112
System\Settings\Presentation
Cross
The shot is displayed with a cross.
09907110(52)
Number
The shot is displayed with its shot number.
09907111(49)
None
The shot is not displayed.
09907112(46)
X
The shot is displayed with an X.
09907113(43)
Dot
The shot is displayed with a dot.
09907114(40)
Thin Cross
The shot is displayed with a thin cross.
09907115(37)
Circle
The shot is displayed with a cross.
99071106(17)
Calibre (Default)
The shot is represented in its true dimensions as a
circle, as long as it is no smaller than 5 Pixel. When
the dimensions are too small, the image changes
automatically to a 'cross'.
99071107(14)
\Shot\Last Shot\Symbol\Size
The image size of the shot can be altered. The size is given in screen dots (Pixels). In the calibre form this setting
has no effect.
14
Dots
99073300(31)
16
Dots
99073301(28)
18
Dots
99073302(25)
20
Dots
99073303(22)
22 (Default)
Dots
99073304(19)
24
Dots
99073305(16)
26
Dots
99073306(13)
28
Dots
99073307(10)
09.08.2010
SIUS AG (c) 2004
65 / 112
System\Settings\Presentation
30
Dots
99073308(07)
32
Dots
99073309(04)
\Shot\Last Shot\Symbol\Inverse
All symbols are primarily conceived as a white symbol on a dark background. Most targets are black in the centre.
The graphics can be inverted. The symbol will then be depicted as a black symbol on a white background.
Off (Default)
The shot is represented normally.
09907140(59)
On
The shot is represented in inverse colours.
09907141(56)
\Shot\Last Shot\Last Shot Window
In the shot window alongside the shot value, the shot number and a secondary score are indicated. In order to
make the representation still clearer, it can be worthwhile to omit the secondary score or the shot number. It is also
possible to switch the shot window off altogether.
\Shot\Last Shot\Last Shot Window\Screen
In the shot window alongside the shot value, the shot number and a secondary score are indicated. In order to
make the representation still clearer, it can be worthwhile to omit the secondary score or the shot number. It is also
possible to switch the shot window off altogether.
Off
The display field for the last shot is faded out.
09907050(38)
Primary
In the shot window only the primary score is shown.
09907051(35)
SNr Prim
In the shot window the shot number and the primary
score are shown.
09907052(32)
SNr Prim Sec (Default)
In the shot window the shot number, primary and
secondary score (100-er score, ISSF tenner ring
score) are displayed.
09907053(29)
Timer
09907054(26)
\Shot\Last Shot\Last Shot Window\Deferred Shots
On (Default)
On
99080701(41)
Off
Off
99080700(44)
\Shot\Last Shot\Display Inner ten
Most target pictures have a small ring defined which besides the normal score is valued as a particularly good hit.
A hit in this ring (the inner ten, Mouche) can be displayed on the control unit by an animated picture on the target
window.
09.08.2010
SIUS AG (c) 2004
66 / 112
System\Settings\Presentation
Off
An inner ten (Mouche) hit is displayed as normal.
99074100(56)
On (Default)
In the event of a hit on the inner ten (Mouche) the
control unit shows concentric circles of different
99074101(53)
sizes one after another several times in the centre of
the target.
\Shot\Standard
In the directory '\Standard' all the settings which affect the depiction of all shots except the last shot are stored.
\Shot\Standard\Symbol
The symbol of a shot can be varied according to appearance, size and background.
\Shot\Standard\Symbol\Form
The form of the symbol can be preset individually for the last shot and jointly for all other shots.
Cross
The shot is displayed with a cross.
09907030(01)
Number
The shot is displayed with its shot number.
09907031(95)
None
The shot is not displayed.
09907032(92)
X
The shot is displayed with an X.
09907033(89)
Dot
The shot is displayed with a dot.
09907034(86)
Thin Cross
The shot is displayed with a thin cross.
09907035(83)
Circle
The shot is displayed with a cross.
99070306(89)
Calibre (Default)
The shot is represented in its true dimensions as a
circle, as long as it is no smaller than 5 Pixel. When
the dimensions are too small, the image changes
automatically to a 'cross'.
99070307(86)
\Shot\Standard\Symbol\Size
The image size of the shot can be altered. The size is given in screen dots (Pixels). In the calibre form this setting
has no effect.
14
Dots
09907040(68)
16
Dots
09907041(65)
09.08.2010
SIUS AG (c) 2004
67 / 112
System\Settings\Presentation
18 (Default)
Dots
09907042(62)
20
Dots
09907043(59)
22
Dots
09907044(56)
24
Dots
09907045(53)
26
Dots
09907046(50)
28
Dots
09907047(47)
30
Dots
09907048(44)
32
Dots
09907049(41)
\Shot\Standard\Symbol\Inverse
All symbols are primarily conceived as a white symbol on a dark background. Most targets are black in the centre.
The graphics can be inverted. The symbol will then be depicted as a black symbol on a white background.
Off
The shot is represented normally.
09907320(04)
On (Default)
In the event of a hit on the inner ten (Mouche) the
control unit shows concentric circles of different
09907321(01)
sizes one after another several times in the centre of
the target.
\Shot\Standard\Print-format
The print format dictates the image of a shot on the printout. Print formats are often prescribed directly by
programs. So the printout at an international contest is laid out differently to that of a compulsory confederation
practice in Switzerland.
\Shot\Standard\Print-format\Use Always
On
99073199(43)
Off (Default)
99073198(46)
Default (Default)
The printer prints the shot with shot number,
direction arrow, primary and secondary score.
09.08.2010
SIUS AG (c) 2004
99073100(49)
68 / 112
System\Settings\Presentation
Xy
On the printer the primary and secondary score and
the XY coordinates are printed out.
99073101(46)
t x/y
As well as the primary score, the time of the shot
and its coordinates are displayed.
99073109(22)
Time
In the 'Time' format the time difference from the first
shot of the group is always depicted.
99073108(25)
Debug
The debug format is only intended for test purposes.
It supplies all the values which have been measured 99073102(43)
by the LON electronic measuring system. As well as
register values the recorded temperature and other
information is listed.
\Shot\Standard\Screen-format
Default (Default)
The shot is displayed with shot number, direction
arrow, primary and secondary score in the list
window.
99070800(62)
Xy
In the list window the primary and secondary scores
and the XY coordinates are displayed.
99070801(59)
t x/y
As well as the primary score, the time of the shot
and its coordinates are displayed.
99070809(35)
Time
Display format 'Time' the time gap to the first shot of
the current group will also be displayed.
99070808(38)
Debug
The debug format is only intended for test purposes.
It supplies all the values which have been measured 99070802(56)
by the LON electronic measuring system. As well as
register values the recorded temperature amongst
others is listed.
\Shot\Standard\Secondary Score
The secondary score can be always switched off.
Off
The secondary score is switched off.
09907120(22)
On (Default)
The secondary score is switched on.
09907121(19)
\Shot\Standard\Clear target after shots
In test and single groups the setting 'Clear target window after shots' enables the target window to be regularly
cleared and so to remain clear. Thereby the shots are counted comprehensively by group. But this is only in test
and single groups. In series groups all shots are shown one after another without shots being cleared in between.
Consequently with the setting 10 in the following program: 'T2 S4 S4 S4' the target window is cleared after 2 shots
09.08.2010
SIUS AG (c) 2004
69 / 112
System\Settings\Presentation
(because the test group has come to an end and the shoot will continue with a single group). Additionally the same
action is carried out in the last 'S4' group after the second shot (because 10 shots have been used in the single
groups).
0
Clears the target window after twenty shots.
99078600(39)
5
Clears the target window after five shots.
99078605(24)
10 (Default)
Clears the target window after ten shots.
99078610(09)
20
Clears the target window after twenty shots.
99078620(76)
\Shot\Cross Shot
In the directory '\Cross shots' the settings which influence the depiction of cross shots (shots from another lane
onto one's own target) are stored.
\Shot\Cross Shot\Show
Cross shots are indicated with a symbol in the right bottom corner of the target window. The symbol remains active
for seven minutes. If the last cross shot is more than seven minutes old, then the symbol is extinguished again.
Additionally in the list window an entry can be generated which draws attention to the cross shot.
Off (Default)
The showing of cross shots is suppressed in the list
window. The first cross shot is displayed with a
symbol in the target window in the bottom right
corner.
09907060(08)
On
Cross shots are displayed in the list window with the
entry 'cross shot'.
09907061(05)
\Shot\Cross Shot\Print
As well as being shown in the target window, cross shots can also be printed.
Off (Default)
Cross shots are not displayed on the printer. In
particular if printing is done onto pre-printed sheets
(federal programs, field shooting) cross shots may
not influence the formatting.
09907170(66)
On
A cross shot is output on the printer.
09907171(63)
\Shot\Illegal Shot
In the directory '\Invalid shots' all the settings which affect the depiction of shots outside the permitted time, during
the stop, pause or show phase, are stored.
\Shot\Illegal Shot\Show
Invalid shots can be displayed in the list window.
Off
The showing of non-allowable shots is suppressed
in the list window.
99073400(22)
On (Default)
Invalid shots are indicated in the list window with
'Invalid Shot'.
09.08.2010
SIUS AG (c) 2004
99073401(19)
70 / 112
System\Settings\Presentation
\Shot\Illegal Shot\Print
Invalid shots can be printed.
Off
Invalid shots are not printed.
99073500(13)
On (Default)
An non-allowable shot is printed out on the score
sheet as 'non-allowable shot'.
99073501(10)
\Shot\Best shot
In serial groups the best shot (low shot) at the end can be shown once more and printed out in round brackets
together with the shot number.
Off
The display of the best low shot is suppressed.
99079700(37)
On (Default)
The best low shot is displayed in series groups.
99079701(34)
Printing
In the directory '\Presentation\Printing' all the settings which control the printer can be changed.
\Printing\Column Configuration
For the matrix printer D93 printer paper which is perforated in the centre is available. With the column configuration
the program can be set up to print out in two columns at once. The perforated paper can subsequently be
separated down the middle. It should however be observed that certain shot print formats (e.g. with ISSF
disciplines) cannot be placed on half of the paper. The information is cut off after 19 characters. This can lead to
loss of information on the printout.
\Printing\Column Configuration\Use Always
On
99071399(11)
Off (Default)
99071398(14)
Left
The program is printed out aligned left. The full width
of the paper is available.
09907130(89)
Right
The program is printed out on the right half of the
paper. Only half the width of the paper is available.
09907131(86)
Double (Default)
The program is printed out twice in parallel. Only
half the width of the paper is available in each case.
09907132(83)
\Printing\Print Protocol
The printing out of shots on the printer during a program can always be switched on and off with 'Print records'.
Off
The records are not printed.
99076300(52)
09.08.2010
SIUS AG (c) 2004
71 / 112
System\Settings\Presentation
On (Default)
The records are printed.
99076301(49)
\Printing\Secondary Score
Although the secondary score is shown, the printout of the secondary score can be suppressed.
Off (Default)
The secondary score is not printed.
09907250(20)
On
The secondary score is printed.
09907251(17)
\Printing\Sighters
Test shots are usually printed out just like all other shots. However, in order that pre-printed score sheets are not
overwritten with test shots, it is possible to block the printing out of test shots.
Off
Test shots are displayed only on the screen.
09907160(96)
On (Default)
Test shots are displayed on the printer. The
exception to this is shooting programs consisting of
only one test group. These shots are never printed.
This was done so that pre-prepared score sheets
could be sued correctly.
09907161(93)
\Printing\Subtotal
The shots of every group are counted together and the result is displayed in the list window and on the printer. It is
possible to suppress these totals on the printout.
Off
Subtotals or group totals are not printed.
09907210(43)
On (Default)
Subtotals or group totals are printed.
09907211(40)
\Printing\Print Overtime
Off
99080600(53)
On (Default)
99080601(50)
\Printing\Number of line feeds
After a program the printer should advance the paper so far that with continuous paper it can be torn off correctly
on the cutting edge of the printer. With pre-printed score sheets it can happen that this paper feed must be altered.
With '\Number of Empty Lines' it is possible to specify how many empty lines (paper feed) should be printed after a
program.
0
Empty lines
99074000(65)
1
Empty lines
99074001(62)
09.08.2010
SIUS AG (c) 2004
72 / 112
System\Settings\Presentation
2
Empty lines
99074002(59)
3
Empty lines
99074003(56)
4
Empty lines
99074004(53)
5
Empty lines
99074005(50)
6
Empty lines
99074006(47)
7
Empty lines
99074007(44)
8
Empty lines
99074008(41)
9
Empty lines
99074009(38)
10
Empty lines
99074010(35)
11 (Default)
Empty lines
99074011(32)
12
Empty lines
99074012(29)
13
Empty lines
99074013(26)
14
Empty lines
99074014(23)
Number of line feeds
After a program the printer should advance the
paper so far that with continuous paper it can be
990645(48)
torn off correctly on the cutting edge of the printer.
With pre-printed score sheets it can happen that this
paper feed must be altered. With '\Number of Empty
Lines' it is possible to specify how many empty lines
(paper feed) should be printed after a program.
Shoot
With the settings '\Presentation\ Program' or '\Presentation\ Group' the form of depiction of expressions and
readouts in the list window can be changed. But many programs have their own fixed format. These settings
should only be changed in consultation with Sius AG.
\Shoot\Print
09.08.2010
SIUS AG (c) 2004
73 / 112
System\Settings\Presentation
\Shoot\Print\Header
Empty
99075100(63)
Name (Default)
99075105(48)
Short
99075101(60)
Line feed
99075102(57)
\Shoot\Programed Timers
This settings determines if the programmed Timers for ISSF-Disziplines should be used or not.
Off (Default)
Disables the programmed Timers fo ISSF-Disziplines
99080800(35)
On
Activates the programmed Timers for ISSFDisziplines
99080801(32)
Practice
With the settings '\Presentation\ Program' or '\Presentation\ Group' the form of depiction of expressions and
readouts in the list window can be changed. But many programs have their own fixed format. These settings
should only be changed in consultation with Sius AG.
\Practice\Print
\Practice\Print\Footer
Total (Default)
99075407(15)
Total with SeqNr
99075412(97)
Group
The directory '\Presentation\Group' contains settings which influence the behaviour of individual groups.
\Group\Reset Shot Number
If this option is selected, the shots within this group are always numbered beginning with a 1. Otherwise the shots
within the whole practice are continuously numbered. Test shots are excluded from this.
Off (Default)
The shot numbers are continuously numbered in a
program.
99073700(92)
On
The numbering of the shots begins again with '1'
with every group.
99073701(89)
\Group\Subtotal
The group totals in a program can be displayed in the program progress window. For completed groups the fire
type and the number of shots (e.g. E2 S4) are replaced by the respective subtotals.
09.08.2010
SIUS AG (c) 2004
74 / 112
System\Settings\Presentation
Off (Default)
The end of program window shows the types of fire
and the active group.
99073600(04)
On
In the program progress window the fire type of the
concluded groups is replaced by the subtotal of the
current group.
99073601(01)
Other
In the directory '\Presentation\Other' can be found the settings which cannot be assigned to another group.
\Other\Control unit
Settings affecting the basic layout of the image are stored under '\Screen'.
\Other\Control unit\Layout
The image on the control unit can be adjusted to meet individual needs as far as possible.
Classic (Default)
The classic representation best meets the most
frequent needs of firers.
99073900(74)
Stop at Left
If the screen is mounted on the right hand side of
the firer, it can be useful for the status notification to
be visible by means of a small movement of the
head. For this reason the status window in the
layout 'Stop Left' was moved. In the layout 'Stop
Left' the status window was omitted for reasons of
space. Parameters that are represented in the
status window are no longer displayed in the list
window.
99073901(71)
Final
If the screen of the control unit is to be made visible
also for the spectators, the target image can be
made as large as possible with the 'Final' layout. In
the 'Final' layout the status window, the practice
progress window and the selection window are not
shown.
99073902(68)
\Other\Control unit\Function Keys
The window with the menu keys is displayed on the LCD of the control unit and at the lower edge of the screen. In
portable devices (handheld) the function key window should not be switched off because this device has no LCD.
Off
The bar with the function keys is concealed. Details
of the keypad mode are only available on the LCD of 99074400(29)
the control unit.
On (Default)
The bar with the function keys is also overlayed on
the screen.
99074401(26)
\Other\Control unit\Status flashing
In order that the firer's attention can better be drawn to the screen, the most important status information (stop,
offline) flashes in the status window. This effect, which can also be distracting, can be turned off with this setting.
Off (Default)
The status window will indicate no status by flashing.
99078800(21)
09.08.2010
SIUS AG (c) 2004
75 / 112
System\Settings\Presentation
On
The most important information (stop, offline, show)
is displayed flashing.
99078801(18)
\Other\Control unit\Practice progress window
The display of the program progress window can be suppressed.
Off
The end of program window is not displayed.
99074300(38)
On (Default)
The end of program window is displayed.
99074301(35)
\Other\Control unit\Large font in Listwindow
Specifies font used in list window.
Off (Default)
Normal font is used in list window.
99080200(89)
On
Large font is used in list window.
99080201(86)
\Other\Message
Under '\Messages' the way the control unit handles messages can be configured.
\Other\Message\Display Messages
The control unit displays various texts as reports in the list window. Many of these reports are laid out in such a
way that they are also displayed on the LCD near the keyboard. With this setting these outputs can be limited.
Off
Reports are no longer displayed.
99073800(83)
On-screen
Only reports that are displayed in the list window are
shown. The readouts on the LCD are suppressed.
99073801(80)
This setting is useful when the display screen is to
be set up directly next to the control unit. In this
situation readouts on the LCD can then be
suppressed.
On LCD
Only reports that are displayed in the LCD are
shown. The readouts in the list window of the screen 99073802(77)
are suppressed. This setting is useful when the
control unit is to be set up some distance away from
the display screen. Usage is then mainly controlled
via the LCD.
On Both (Default)
All reports are displayed both on the LCD and in the
list window of the screen.
99073803(74)
\Other\Message\Target Feed Message
The S10, the S25/50, the S101 and other targets have a materials handling (paper or rubber band feed). If the
motors stall, the material runs out or the band jams, then the target reports a band feed error to the control unit. It
is essential to correct this error as missing band feed can lead to incorrect measurements in the detection system.
However, the display of the error message can be suppressed. This only serves a useful purpose when no targets
with band feed have been installed or for test purposes, when no band is available, but the unit nonetheless needs
to run in simulation mode.
09.08.2010
SIUS AG (c) 2004
76 / 112
System\Settings\Presentation
Off
Reported line feed errors are suppressed.
99073000(58)
On-screen (Default)
Reported line feed errors are only displayed in the
list window of the screen.
99073001(55)
On printer
Reported line feed errors are only printed.
99073002(52)
On Both
Reported line feed errors are shown in the list
window and printed.
99073003(49)
\Other\Display target name
The target description and the names of the active score methods are displayed in the upper left corner of the
target window.
Off
The target description and the score information are
suppressed.
99074200(47)
On (Default)
In the target window the target name and the score
information are shown.
99074201(44)
\Other\Display calibre
The calibre is displayed together with the measurement in the upper left corner of the target window. If the calibre
is written inside round brackets, then in addition this means that the score is calculated as centre score. The
advantage of score methods with central score is that they are independent of the calibre.
Off
The calibre information is suppressed.
99078300(66)
On (Default)
The calibre information is displayed.
99078301(63)
\Other\Indication
There are situations in which the firer should not be informed about the shot which has been fired. If the screen is
switched off, then the shot situation is not relayed. No entry is made in the list window and no printout is produced.
Only the shot number is displayed in the shot window.
Off
All displays (graphics window, list window, shot
window and printer) are suppressed. The shot
information is visible only on an associated PC and
in the log. The function is used when statistical
measurements need to be made and the firer must
not be influenced by the result.
09907260(87)
On (Default)
Images are no longer suppressed.
09907261(84)
Parameter
Parameters are optional functions that can be turned on if desired. Parameters can be set in many ways. There are
parameters that affect the image, parameters that calculate statistical values, and many more. Parameters must be
switched on before a particular program is input.
MPI
The MPI (mean point of impact) calculates the mean point of impact of the last five shots and indicates this spot as
09.08.2010
SIUS AG (c) 2004
77 / 112
System\Settings\Parameter
coordinates in the statistics window and as a small square in the target window. The number of shots that were
included in the calculation of the MPI can also optionally be displayed in the statistics window.
\MPI\Text
The text readout in the statistics window can be suppressed.
Off
Only the small square on the site of the mean hit
point is indicated. The text readout in the statistics
window is suppressed.
99079500(55)
On (Default)
In addition to the graphic square in the statistics
window a text with direction and place details is
displayed via the MPI.
99079501(52)
\MPI\MPI
The MPI can be turned on and off as a whole (graphics and text).
Off
The MPI is not calculated.
99078100(84)
On (Default)
The MPI is calculated.
99078101(81)
Simulator SCB
The SCB parameter (scoreboard) simulates the details of a scoreboard in the statistics window.
Off
The SCB is not copied.
99080100(01)
On (Default)
The scoreboard is replicated in the statistics window.
99080101(95)
Divisions
The divider is a score method which is used above all in Germany. It shows the distance of the point of entry of a
shot from the centre of the target in 1/10 millimetre. The goal of a firer is to achieve the lowest possible number of
dividers. The divider exists as a parameter and is displayed in the statistics window. In addition the divider values
of all shots in one program are added up. The divider can be chosen as a score method in free series. In this way
it is possible to select the divider as a primary or secondary score.
Off (Default)
The divider parameter in the statistics window is
turned off.
99079300(73)
On
The divider parameter in the statistics window is
turned on.
99079301(70)
Fi
The parameter Fi indicates the distance between the shots which are furthest apart in a group in the statistics
window.
Off (Default)
The parameter Fi is not calculated.
99079100(91)
On
The parameter Fi is calculated.
99079101(88)
09.08.2010
SIUS AG (c) 2004
78 / 112
System\Settings\Parameter
FiFi
The parameter FiFi indicates the distance between the shots which are furthest apart in an entire program in the
statistics window. With very large numbers of shots, this parameter is very calculation intensive and the operating
rate of the control unit can become noticeably slower.
Off (Default)
The parameter FiFi is not calculated.
99079200(82)
On
The parameter FiFi is calculated.
99079201(79)
Biathlon
Off (Default)
99079000(03)
On
99079001(97)
Spread
The distance between those shots which lie furthest apart horizontally is calculated and displayed in the statistics
window. The distance between those shots which lie furthest apart vertically is similarly calculated and displayed.
Off (Default)
The X and Y ranges are not calculated.
99080000(10)
On
The X and Y ranges are calculated.
99080001(07)
Language
The control unit supports several languages. The language of the user guidance can be individually adjusted.
English (Default)
The menu operation is displayed in English.
99070200(19)
Deutsch
The menu operation is displayed in German.
99070201(16)
Language
The control unit supports several languages. The language of the user guidance can be individually adjusted.
English (Default)
The menu operation is displayed in English.
99070200(19)
Deutsch
The menu operation is displayed in German.
99070201(16)
Francais
The menu operation is displayed in French.
99070202(13)
Español
The menu operation is displayed in Spanish.
99070207(95)
Dansk
The menu operation is displayed in Danish.
99070204(07)
09.08.2010
SIUS AG (c) 2004
79 / 112
System\Settings\Language
Norsk
The menu operation is displayed in Norwegian.
99070205(04)
Svenska
The menu operation is displayed in Swedish.
99070206(01)
Italiano
The menu operation is displayed in Italian.
99070203(10)
Russian
99070208(92)
Time
The clock time that is shown in the title bar can be set and the form of the representation can be changed.
Adjust Clock
The clock time can be set on every control unit. If several control units are connected together over a LON
network, then every adjustment to the time will be relayed to all the control units. At best the time on the control
unit is always synchronised with the lowest subnet number. The control unit with the lowest subnet number is
therefore automatically responsible for ensuring that all the connected devices are synchronised. To ensure
correct escore of shots, above all when shooting takes place with a shot logoff, the correct clock time on all
devices is most important.
Year minus 1
One year will be subtracted from the year set now.
99063100(76)
Year plus 1
One year is added to the year that is set now.
99063101(73)
Month minus 1
One month will be subtracted from the month set
now.
99063102(70)
Month plus 1
One month is added to the month that is set now.
99063103(67)
Day minus 1
One day will be subtracted from the day set now.
99063104(64)
Day plus 1
One day will be added to the day set now.
99063105(61)
Hour minus 1
One hour will be subtracted from the hour set now.
99063106(58)
Hour plus 1
One hour is added to the hour that is set now.
99063107(55)
Minute minus 1
One minute will be subtracted from the minute set
now.
99063108(52)
Minute plus 1
One minute is added to the minute that is set now.
99063109(49)
09.08.2010
SIUS AG (c) 2004
80 / 112
System\Settings\Time
Set second zero
The selected minute starts afresh.
99063110(46)
Date format
The date format can be adjusted according to the circumstances of the country.
Short format
The date in short format looks for example like this:
27.09 17:32
99076900(95)
European (Default)
The date in 'European' format looks for example like
this: 27.09.2004 17:32
99076901(92)
European with Seconds
The date in 'European plus seconds' format looks for
example like this: 27.09.2004 17:32:15
99076902(89)
US
The date in 'US' format looks for example like this:
09/27/2004 17:32
99076903(86)
US+Seconds
The date in 'US plus seconds' format looks for
example like this: 09/27/2004 17:32:15
99076904(83)
Other
The directory '\Other\Settings' contains all settings that cannot be unequivocally classified in any other category.
Start
Start settings concern the system startup(switching on) on the one hand, and variations in program start settings
on the other hand.
\Start\Enable Repeat
After a program has been shot the control menu changes automatically. When the status changes to 'Stop', a new
button 'Repeat' appears. There are occasions when a firer may shoot a program only once. In this case the
permission for 'Repeat' must be denied.
Off
The function 'Repeat' is barred.
99077100(77)
On (Default)
The function 'Repeat' is permitted.
99077101(74)
\Start\Free series start setting
Free series are represented in the practice progress window with three open groups. The method of operation of
the free series is described in the user manual. The start setting defines which of the three groups should be
started.
Sighters (Default)
Every free series starts with the test group. In the
practice progress window the test group T is on a
white background.
99079400(64)
Shot by Shot
Alternatively a free series can also be started
directly with the open single group S-.
09.08.2010
SIUS AG (c) 2004
99079401(61)
81 / 112
System\Settings\Other
\Start\Startup program
If a program has been selected this can be saved as a start-up program. The control unit will then in future
automatically load the start-up program as long as no rebuild has been launched. User programs cannot be
consigned as start-up programs. If the start-up program is saved after a user program has been loaded, in future
the control unit will start up with a free series but with the right target.
Clear
If an autostart program has been saved, then this
setting is erased. In future the control unit will not
automatically select any program when turned on.
990798000000(58)
Save
The program that has currently been chosen will
load automatically in future when the control unit is
turned on.
990798065535(72)
\Start\SC-Programs
\Start\SC-Programs\Single Execution
Off (Default)
99081100(08)
On
99081101(05)
\Start\Scale Factor
In some situations targets have to be scaled because of shooting range reasons. For creating comparable
shooting programs it is possible to resize targets in that way that other distances may be simulatet. For example a
300 Meter target was resized to 2/3 to use it at 200 Meter distance. Scale Factor can now be set to 667 for using
the original 300 meter target from the catalogue but shooting on smaller, nearer target on 200 meter.
Reset
Resets the scale factor to its standard value.
9908101000(58)
Scale Factor (600)
9908100600(94)
Set Scale Factor
Starts an editor for having the scale factor entered.
Its value has to be between 100 and 9999 where
1000 is the standard value.
99064700(29)
\Start\Target Alternative
Setting for special variants of programs.
Default
Default
99080900(26)
Right
Used for Moving Mosse Exercise starting on right
side instead of left side.
99080901(23)
\Start\Enable Autoreset
Under certain conditions the resources of the control unit can become limited. This affects mainly the on hand
working memory, its fragmentation and the working speed of the control unit. If certain limits are exceeded, the
control unit can restart by itself and thus fix the resource shortage. This only occurs when the status of the control
unit has been on 'Stop' for a long time or if the screen saver is activated. In these situations the control unit starts
up again automatically.
09.08.2010
SIUS AG (c) 2004
82 / 112
System\Settings\Other
Off
The control unit may not be restarted automatically.
99078400(57)
On (Default)
The control unit may restart automatically under
certain conditions.
99078401(54)
Filter
With many filters the menu can be shortened to those items which the user finds most essential. For instance if a
certain distance is selected, all other distances and the programs associated with them can be suppressed. Thus
so-called filter dimensions are created (user groups, distance, category etc.). A filter dimension contains several
filter characteristics. The dimension 'User Group' comprises the characteristics Standard, Advanced, Administrator
and Sius. A comprehensive description of the filter options can be found in the user manual.
\Filter\Distance
All the targets and programs were organised as a first priority by distance. Target images that are used exclusively
for one distance are filed accordingly. The distance filter is the most effective filter.
\Filter\Distance\Other
Targets and programs that cannot be assigned unequivocally to one distance, or that are regularly used for various
distances.
Off (Default)
The filter characteristic is deactivated.
990635030400(49)
On
The filter characteristic is activated.
990635030401(46)
\Filter\Distance\10m
Targets and programs that are employed for 10 metre distance.
Off (Default)
The filter characteristic is deactivated.
990635030000(85)
On
The filter characteristic is activated.
990635030001(82)
\Filter\Distance\25m
Targets and programs that are employed for 25 metre distance.
Off (Default)
The filter characteristic is deactivated.
990635030100(76)
On
The filter characteristic is activated.
990635030101(73)
\Filter\Distance\50m
Targets and programs that are employed for 50 metre distance.
Off (Default)
The filter characteristic is deactivated.
990635030200(67)
On
The filter characteristic is activated.
990635030201(64)
\Filter\Distance\300m
Targets and programs that are employed for 300 metre distance.
09.08.2010
SIUS AG (c) 2004
83 / 112
System\Settings\Other
Off (Default)
The filter characteristic is deactivated.
990635030300(58)
On
The filter characteristic is activated.
990635030301(55)
Reset
Switch off all settings of this filter dimension and
thereby deactivate filtering in this dimension.
990635039902(61)
\Filter\Category
Programs and targets are grouped in second priority after categories. This was with the intention that programs or
a target could be assigned as far as possible to the most widespread category. This means for example that the
pistol target for 50 metres is to be found under ISSF, although this target is also frequently used in Switzerland.
But ISSF is a more general category than Switzerland. Therefore this target image was stored under ISSF.
\Filter\Category\Other
Programs or targets that do not fit into any other category.
Off (Default)
The filter characteristic is deactivated.
990635010800(67)
On
The filter characteristic is activated.
990635010801(64)
\Filter\Category\ISSF
Targets and programs that are regulated by the ISSF.
Off (Default)
The filter characteristic is deactivated.
990635010000(42)
On
The filter characteristic is activated.
990635010001(39)
\Filter\Category\CISM
Targets and programs that are regulated by the CISM.
Off (Default)
The filter characteristic is deactivated.
990635010100(33)
On
The filter characteristic is activated.
990635010101(30)
\Filter\Category\Hunting
Targets and programs that are used exclusively as hunting targets or hunting programs.
Off (Default)
The filter characteristic is deactivated.
990635010400(06)
On
The filter characteristic is activated.
990635010401(03)
\Filter\Category\Belgium
Targets and programs that are used almost exclusively in Belgium..
09.08.2010
SIUS AG (c) 2004
84 / 112
System\Settings\Other
Off (Default)
The filter characteristic is deactivated.
990635011000(49)
On
The filter characteristic is activated.
990635011001(46)
\Filter\Category\Sui
Targets and programs that are used almost exclusively in Switzerland.
Off (Default)
The filter characteristic is deactivated.
990635010200(24)
On
The filter characteristic is activated.
990635010201(21)
\Filter\Category\Scandinavia
Targets and programs that are used almost exclusively in Scandinavia.
Off (Default)
The filter characteristic is deactivated.
990635010300(15)
On
The filter characteristic is activated.
990635010301(12)
\Filter\Category\Military
The category Military forms a subcategory in various regions. For example in Scandinavia public shoots and
military contests are common. With the category 'Military' the targets and programs that are used exclusively for
public sport are excluded.
Off (Default)
The filter characteristic is deactivated.
990635010900(58)
On
The filter characteristic is activated.
990635010901(55)
Reset
Switch off all settings of this filter dimension and
thereby deactivate filtering in this dimension.
990635019902(18)
\Filter\Weapon
Certain types of weapons are only employed for certain distances. For example air pressure weapons are
employed only for 10 metres and 25 metres, and pistols are not used for 300 metres. For a setup where
exclusively pistols are to be shot, all rifle targets and rifle programs can be masked by the use of a filter.
\Filter\Weapon\Other
All targets and programs that cannot be assigned to another weapon type.
Off (Default)
The filter characteristic is deactivated.
990635050400(92)
On
The filter characteristic is activated.
990635050401(89)
\Filter\Weapon\Rifle
Targets and programs that are shot exclusively with rifles.
09.08.2010
SIUS AG (c) 2004
85 / 112
System\Settings\Other
Off (Default)
The filter characteristic is deactivated.
990635050000(31)
On
The filter characteristic is activated.
990635050001(28)
\Filter\Weapon\Pistol
Targets and programs that are shot exclusively with pistols.
Off (Default)
The filter characteristic is deactivated.
990635050100(22)
On
The filter characteristic is activated.
990635050101(19)
\Filter\Weapon\Air Rifle
Targets and programs that are shot exclusively with air rifles.
Off (Default)
The filter characteristic is deactivated.
990635050200(13)
On
The filter characteristic is activated.
990635050201(10)
\Filter\Weapon\Air Pistol
Targets and programs that are shot exclusively with air pistols.
Off (Default)
The filter characteristic is deactivated.
990635050300(04)
On
The filter characteristic is activated.
990635050301(01)
Reset
Switch off all settings of this filter dimension and
thereby deactivate filtering in this dimension.
990635059902(07)
\Filter\User Group
With the filter 'User Group' a simplified user authorisation can be adopted. Different levels of authority are
assigned to the different user groups.
\Filter\User Group\Standard
A standard user can use only the normal shooting operation. He is forbidden to change settings or even to
configure hardware components.
Off (Default)
The filter characteristic is deactivated.
990635040000(58)
On
The filter characteristic is activated.
990635040001(55)
\Filter\User Group\Advanced
An 'Advanced' user can amend the major settings and print out supplementary reports.
Off (Default)
The filter characteristic is deactivated.
990635040100(49)
09.08.2010
SIUS AG (c) 2004
86 / 112
System\Settings\Other
On
The filter characteristic is activated.
990635040101(46)
\Filter\User Group\Administrator
Maintenance tasks and hardware settings can only be amended if at least one administrator is configured.
Off (Default)
The filter characteristic is deactivated.
990635040200(40)
On
The filter characteristic is activated.
990635040201(37)
\Filter\User Group\Sius
Special functions are reserved for Sius staff.
Off (Default)
The filter characteristic is deactivated.
990635040300(31)
On
The filter characteristic is activated.
990635040301(28)
Reset
Switch off all settings of this filter dimension and
thereby deactivate filtering in this dimension.
990635049902(34)
\Filter\Function
All the functions of the control unit were organised in function groups. By filtering individual function group the
fields which are not needed can be masked.
\Filter\Function\Other
Functions which cannot be assigned to another function group.
Off (Default)
The filter characteristic is deactivated.
990635020200(94)
On
The filter characteristic is activated.
990635020201(91)
\Filter\Function\Logon
Functions which are needed for the identification of firer.
Off (Default)
The filter characteristic is deactivated.
990635020000(15)
On
The filter characteristic is activated.
990635020001(12)
\Filter\Function\Free Series
Functions which are needed only in free series.
Off (Default)
The filter characteristic is deactivated.
990635020100(06)
On
The filter characteristic is activated.
990635020101(03)
09.08.2010
SIUS AG (c) 2004
87 / 112
System\Settings\Other
\Filter\Function\Programs
Functions which are needed only in free series.
Off (Default)
The filter characteristic is deactivated.
990635020300(85)
On
The filter characteristic is activated.
990635020301(82)
\Filter\Function\Firer number
When only the function 'Firer number' is permitted, but not the function 'Report', then the firer number can be
retrieved but the other information about position, weapon, sight etc. remains invisible.
Off (Default)
The filter characteristic is deactivated.
990635020400(76)
On
The filter characteristic is activated.
990635020401(73)
Reset
Switch off all settings of this filter dimension and
thereby deactivate filtering in this dimension.
990635029902(88)
\Filter\Mode
In contrast to the other settings, the Mode does not filter any menu functions. In previous Sius systems the mode
was urgently needed so that the correct detection system would be recognised. In the control unit this information
is no longer necessary. But the mode can be used as before as a lock. Every target and every program identify a
particular mode. A group can only be loaded when the filter Mode is set to 'Off' or when the program mode
corresponds to the set mode. This lock also functions when the target or the program are entered via barcodes. If
for example the mode '300m' is selected, no further hunting images can be selected. The control unit always
issues an appropriate error warning in the list window.
Off (Default)
All the programs can be selected.
99071899(63)
Air pressure weapons
Shooting mode for air pressure weapons and
programs that are shot over a 10 metre distance.
(Mode 2)
99071802(63)
25m
Mode for 25 metre and 50 metre small calibre and
large calibre pistols as well as for small calibre rifles. 99071803(60)
(Mode 3)
50m
Targets and programs that are shot from 50 metres.
This concerns large and small calibre pistols and
small calibre rifles as well as special Swiss groups
(Morgarten). (Mode 4)
99071804(57)
300m
Targets and programs for 300 metre disciplines
(Mode 0)
99071800(69)
Hunting
Hunting targets and hunting programs (Mode 1)
99071801(66)
09.08.2010
SIUS AG (c) 2004
88 / 112
System\Settings\Other
Scandinavia
Scandinavian targets (Denmark, Norway, Sweden)
(Mode 11)
99071811(36)
Running Target
Targets and programs for the running target for 10
and 50 metres (Mode 12)
99071812(33)
Biathlon
Targets and programs for biathlon disciplines (Mode
13)
99071813(30)
Calibre
With most targets and programs a certain calibre is implicitly assumed. With targets that are well known to be fired
at with different weapons types and thus with different calibres, the most common selection options are already
available. The calibre is used on the one hand for the image in the graphics window, and on the other hand certain
score methods require the calibre to calculate the score. In the modern ISSF disciplines the score is calculated by
means of the shot hole centre (centre score). The calibre is fixed (e.g. air pressure disciplines 4.5mm.) Even when
a larger calibre is employed, these disciplines are evaluated with the calibre that was fixed. Such score methods
are identified in the target window with the note 'centre score'. With older targets that are evaluated with edge
score, the selected calibre has an effect on the score. Changes to this setting are therefore logged.
\Calibre\Use Always
On
99079699(40)
Off (Default)
99079698(43)
Off
All disciplines that are not assessed with a fixed
given calibre are assessed with centre score.
990796000000(26)
450
All disciplines that are not assessed with a fixed
given calibre or with centre score are assessed with
4.5mm calibre.
990796000450(34)
560
All disciplines that are not assessed with a fixed
given calibre or with centre score are assessed with
5.6mm calibre.
990796000560(92)
800
All disciplines that are not assessed with a fixed
given calibre or with centre score are assessed with
8.0mm calibre.
990796000800(51)
900
All disciplines that are not assessed with a fixed
given calibre or with centre score are assessed with
9.0mm calibre.
990796000900(42)
965
All disciplines that are not assessed with a fixed
given calibre or with centre score are assessed with
9.65mm calibre.
09.08.2010
SIUS AG (c) 2004
990796000965(41)
89 / 112
System\Settings\Other
1158
990796001158(44)
1270
990796001270(96)
Control Mode
The control mode regulates various stages of the remote control. The control unit is configured so that for example
it can be controlled remotely by Siusdata ®.
Local (Default)
All functions can be carried out via the keyboard or
the barcode reader.
09907790(49)
Practice Control
In certain ISSF disciplines (e.g. 3*40 rifle shoot) the
control unit goes into a paused state. This state can
be released with a command from SiusData ®. In
this way a change of position can be ordered for a
whole score.
09907791(46)
Remote
If the control unit is totally remotely controlled,
entries via the keyboard or the barcode reader are
barred.
09907792(43)
Demo
The demo mode is displayed in the status window (small font). In demo mode shots can be created via the insert
key ('Ins'). The control unit requests the connected target to create a shot at a chance coordinate and to send this
back to the control unit. The demo shot implicitly tests both the connected target and the communication. Demo
mode is switched off every time at startup.
Off (Default)
Turns off the demo mode.
09907000(91)
On
Selects demo mode.
09907001(88)
Activate remote barcode
This command sets the CU in the remote barcode
mode. While activated all Barcodes from the
connected Barcodereader will be sent to the
specified Lane. To change the selected lane press
the specified keys on the keyboard, to exit
remotebarcode mode press escape. The
configuration of the key-lane selection can be
downloaded from siusdata, default setting is
099067(07)
Demonstration Mode
099068(04)
Settings Control
It is possible to store one's own setting configurations in the permanent memory of a control unit. These customer
settings will not be lost even with a change of battery. Even during a 'cold start' these settings will not be overwritten by
the factory settings. So it can be guaranteed that your own settings can also be selected as standard. The settings will
only be lost if a new software version is loaded. It is possible to save these settings as a file on a computer and with
SiusData to load them via the LON network onto all connected control units. Warm start: A warm start is triggered by a
short power failure or by the explicit command '\Maintenance\Warm-Start'. The current settings are preserved during a
warm start. Cold start: A cold start can be forced if during boot-up the cold start button is pressed (above the two 1mm
drillholes on the back of the control unit, on the right near the control unit socket). The control unit confirms the cold start
09.08.2010
SIUS AG (c) 2004
90 / 112
System\Settings\Settings Control
with a beep. A cold start is also necessary if the memory content is lost due to too little battery power during an electricity
failure. The control unit announces this process with the message 'crc-Failed'. In a cold start the user settings that were
most recently saved are always loaded. The devices are supplied with various user settings. In particular the filters are
preconfigured for the customer.
Factory Settings
With the command 'Factory Settings' all settings in
the volatile memory are reset to the factory settings. 09903601(06)
The customer settings are stored. In the event of a
system 'cold start' the customer settings are also
reloaded with this command. In order for the factory
settings to be selected as the standard settings after
a 'cold start', they must be saved as customer
settings following this command.
Customer Settings
All settings that were changed during the current
operation are reset to the customer settings. The
same occurs if a cold start takes place on the
control unit, or if the buffer battery is changed.
09903612(70)
Save Customer Settings
The settings in current use are saved as customer
settings. This process writes data from the volatile
memory into the non-volatile memory. The process
only lasts a few seconds but it is very important that
it is carried out completely as otherwise the control
unit can be damaged. If the process is not carried
out completely, it can happen that the control unit
will no longer start after the next interruption to the
power supply. In this event the software would have
to be reinstalled. The control unit must not be
switched off during the memory process. The power
supply must not be interrupted. The conclusion of
the memory process is signalled with a beep.
09903613(67)
Maintenance
The directory '\Maintenance' contains functions which go beyond daily use. Diagnosis, upkeep and error searches are
supported through various start points. These functions should be carried out only by well trained staff.
Reports
Expanded reports are listed under '\Maintenance\Reports'. Also kept here are the functions which are available for
erasing the data belonging to these reports and so to set the corresponding report to zero. For example the log can be
deleted or the software shot counter can be reset to zero.
Settings
Printing out settings:
Print
Prints out a list of the current settings that differ from
the factory settings. In addition the shaft settings of
09903602(03)
the target images and the filter configurations are
listed, insofar as these differ from the factory
settings.
Shoot
Many settings are taken over into a program when
the program is launched. Additionally a program use
of additional settings that were stored when the
program was being developed. The command
'\Settings\Program' prints all the settings of the
actively selected program.
09.08.2010
SIUS AG (c) 2004
09903610(76)
91 / 112
System\Maintenance\Reports
Shot Counter
Mechanical shot counters:
The optional mechanical shot counter only counts the shots on your own target. It cannot be reset. Demo shots or
inserted no scores are not counted. A detailed description of the whole function can be found in the user manual
under 'Mechanical shot counters'.
Software shot counters:
The software shot counter counts shots in different categories. Own shots, cross shots, missed shots, demo shots
etc. are differentiated and displayed separately. The shot count report is displayed in the list window and provided
a printer is connected and switched on, is printed out. The shot counters are connected to the control units. If the
settings are reset to factory settings, the shot counts are also reset to zero. The same occurs when the battery has
to be changed. With a normal interruption to the power supply, the values are not lost. The software shot counters
can also be reset independently of the settings under '\Maintenance\Reports\Shot Counters'.
Reset Shot Counter
Resets the software shot counter back to zero.
09903609(79)
Invalid shots
Non-allowable shots (shots during the Stop, Pause or the Show Phase and cross shots) are not only counted, they
are kept in the control unit as pending and can be queried at any time. The shots are then shown with the time and
if possible with the score. With a warm start or with the command 'Erase' under '\Maintenance\Invalid Shots' the
report can be rejected. The shots remain in the log throughout and furthermore can be documented in a log
printout.
Clear
The report on the latest cross shots and illegal shots
is erased.
990560(12)
Log
Events that are of relevance for the duration of a program are filed in the memory (events memory, log). This
information is needed to be able to reproduce a program after a power interruption. The CU931 investigates this
data at every system start-up. If it is established that the last program to be shot was not correctly ended, then a
repetition process is introduced. By means of the log past programs can also be reloaded or a copy can be printed
once again. The log is stored in the volatile memory of the control unit, which is buffered with a battery. The data is
protected from misinterpretation by a check sum. If the check sum is not correct at system start-up, for example
due to a faulty battery, the log is initialised again. The control unit communicates this by a triple beep and a report
in the list window. The log is restricted in memory size. In the event of an overload, the oldest events are
overwritten by the most recent on a rolling basis. Typically more than ten programs can be stored in the log. The
log can also be manually erased under '\Maintenance\Reports\Log'. The format of the printout is described in the
user manual.
Clear
The log memory is explicitly wiped. Because this
means that previous programs are irretrievably
erased, this command must be authorised by a
further confirmation.
Confirm
099057(37)
Log Hex
The 'Log-Hex' is an expanded log printout which
prints out all events additionally in hexadecimal
form. This printout allows events to be analysed at a
very detailed level. The printout is exclusively used
to search for software errors.
990559(15)
Debug
With the '\Debug' reports internal conditions of the control unit can be displayed. This report permits a diagnosis of
the control unit in respect of the demand, the speed of operation or the load. They serve to enable the speed and
reliability of the devices to be optimised.
Report Processes
Reports the number of runs as well as the time
taken by the individual processes.
09.08.2010
SIUS AG (c) 2004
09903611(73)
92 / 112
System\Maintenance\Reports
Classes
Prints a report that indicates for each class how
many instances are presently available, how often
the designer has been contacted and how high the
greatest occurrence of the class was in the past.
09903605(91)
Self Test
Hardware components can be tested by some special commands. These tests are normally used to fulfill the final check
of a new installation.
They can be used to filter an erroneous function while the system is running.
Shot Counter
The mechanical shot counter can be made to start counting by a self test. The chosen number triggers the
corresponding number of counting pulses. Thus the fastest possible meter pulse rate can be selected. The
mechanical counter cannot skip any of these pulses.
1
Counting impulse(s) on the mechanical shot counters
99035121(11)
2
Counting impulse(s) on the mechanical shot counters
99035122(08)
3
Counting impulse(s) on the mechanical shot counters
99035123(05)
4
Counting impulse(s) on the mechanical shot counters
99035124(02)
5
Counting impulse(s) on the mechanical shot counters
99035125(96)
6
Counting impulse(s) on the mechanical shot counters
99035126(93)
7
Counting impulse(s) on the mechanical shot counters
99035127(90)
8
Counting impulse(s) on the mechanical shot counters
99035128(87)
9
Counting impulse(s) on the mechanical shot counters
99035129(84)
Target test
The target test requests the most important status
information from the LON electronic measuring
99063300(58)
system. Along with the software and hardware
version, the temperature, the assembly alignment
and the Target Index Code are conveyed. The
running time of the enquiry indirectly provides
information on how well synchronised the equipment
is with respect to time. The target test can be used
to test the network cabling to the LON electronic
measuring system and the functioning of the
communication chips on the control unit and the
LON electronic measuring system. The target test
only functions if a LON electronic measuring system
is connected and linked to the control unit via the
09.08.2010
SIUS AG (c) 2004
93 / 112
System\Maintenance\Self Test
correct subnet (please refer to
'\Hardware\Target\Connections').
Keyboard
The keyboard test switches the control unit into a
special keyboard test mode. Every keystroke is
confirmed by an entry in the list window. Hitting the
Escape key permits this keyboard test to be exited.
09903505(03)
Scoreboard
The scoreboard itself has a test program available.
This test program can be started from the control
unit on its own scoreboard (subnet Addressing must
be in agreement).
09903508(91)
Beep
The beep test issues a series of ten short beeps one
after another. They must be acoustically audible
09903511(82)
from the control unit.
Control unit reset
With a warm start the control unit is forced to start up again (reboot process). This corresponds to the same process as
when the control unit is turned on without power for a short time. (see also '\Settings\Setting controls')
Confirm
09903600(09)
Debug
Functions that serve only for error detection are stored under '\Maintenance\Debug'.
Debug Mode
The debug mode allows all events which are being processed in the control unit also to be represented visually.
This representation permits a precise search for errors. In the case of reproducible error, it can happen that you
will be instructed by Sius colleagues to turn on this debug mode, so that the printout can subsequently be
analysed and the error can thereby be controlled.
Off (Default)
The events processed by the control unit are not
displayed.
99070700(71)
On
The events processed by the control unit are
displayed in the list window.
99070701(68)
Print
The events processed by the control unit are
displayed in the list window and additionally on the
connected printer.
99070702(65)
Trap
This function is only used for errors that are very difficult to reproduce. In the software versions that are specially
produced for this, an 'error case' can be programmed in. At the moment when the error is recognised, a special
response can be triggered. Mostly the debug mode is activated as a special treatment.
Off (Default)
The control unit operates without special error
recognition.
99078200(75)
On
The special treatment is activated.
99078201(72)
09.08.2010
SIUS AG (c) 2004
94 / 112
System\Hardware
Hardware
Settings that directly affect the hardware components of the control unit are stored under '\Hardware'. Some of these
components are optionally available for the equipment and only have an effect when these components are running.
SCB
SCB
Communication to the scoreboard can be basically suppressed. Communication reduces the speed of execution of
the control unit by several percent. It is therefore worthwhile to configure the SCB as 'Off' when it is not present.
Communication to the SCB must be switched on before a program is loaded.
Off (Default)
The SCB is not responded to.
99078900(12)
On
The SCB is responded to.
99078901(09)
Control unit
'\Screen' contains several hardware settings that directly affect the control unit.
Set Subnet
Sius AG devices communicate with one another via the field bus LON. Each device has its own address. One part
of this address is the so-called subnet. The LON electronic measuring system and the control unit with the same
subnet always belong together. Different lanes must be correspondingly differentiated in the subnet. Every LON
electronic measuring system sends its own detected shots to the control unit in the same subnet in which it is itself
addressed. A LON electronic measuring system with subnet 5 sends its shots to the control unit with subnet 5.
By setting a subnet on a control unit only the address of the control unit is affected. A previously linked LON
electronic measuring system must be reconnected after this alteration (please refer to '\Hardware\Target\Connect'
and instructions for use.
Insofar as a LON electronic measuring system is located in the same subnet, the status of the control unit changes
from 'Offline' to 'Stop' or 'Ready' according to whether a program is selected or not.
The subnet can be selected via the 10-er keyboard. Pressing the Enter key confirms a given value. With 'Esc' the
entry can be cancelled. The F5 key allows incorrect entries to be corrected in time.
\Set Subnet\1..9
1 (Default)
9907270001(58)
2
9907270002(55)
3
9907270003(52)
4
9907270004(49)
5
9907270005(46)
6
9907270006(43)
7
9907270007(40)
09.08.2010
SIUS AG (c) 2004
95 / 112
System\Hardware\Control unit
8
9907270008(37)
9
9907270009(34)
\Set Subnet\10..19
10
9907270010(31)
11
9907270011(28)
12
9907270012(25)
13
9907270013(22)
14
9907270014(19)
15
9907270015(16)
16
9907270016(13)
17
9907270017(10)
18
9907270018(07)
19
9907270019(04)
\Set Subnet\20..29
20
9907270020(01)
21
9907270021(95)
22
9907270022(92)
23
9907270023(89)
09.08.2010
SIUS AG (c) 2004
96 / 112
System\Hardware\Control unit
24
9907270024(86)
25
9907270025(83)
26
9907270026(80)
27
9907270027(77)
28
9907270028(74)
29
9907270029(71)
\Set Subnet\30..39
30
9907270030(68)
31
9907270031(65)
32
9907270032(62)
33
9907270033(59)
34
9907270034(56)
35
9907270035(53)
36
9907270036(50)
37
9907270037(47)
38
9907270038(44)
39
9907270039(41)
\Set Subnet\40..49
09.08.2010
SIUS AG (c) 2004
97 / 112
System\Hardware\Control unit
40
9907270040(38)
41
9907270041(35)
42
9907270042(32)
43
9907270043(29)
44
9907270044(26)
45
9907270045(23)
46
9907270046(20)
47
9907270047(17)
48
9907270048(14)
49
9907270049(11)
\Set Subnet\50..59
50
9907270050(08)
51
9907270051(05)
52
9907270052(02)
53
9907270053(96)
54
9907270054(93)
55
9907270055(90)
56
9907270056(87)
09.08.2010
SIUS AG (c) 2004
98 / 112
System\Hardware\Control unit
57
9907270057(84)
58
9907270058(81)
59
9907270059(78)
\Set Subnet\60..69
60
9907270060(75)
61
9907270061(72)
62
9907270062(69)
63
9907270063(66)
64
9907270064(63)
65
9907270065(60)
66
9907270066(57)
67
9907270067(54)
68
9907270068(51)
69
9907270069(48)
\Set Subnet\70..79
70
9907270070(45)
71
9907270071(42)
72
9907270072(39)
09.08.2010
SIUS AG (c) 2004
99 / 112
System\Hardware\Control unit
73
9907270073(36)
74
9907270074(33)
75
9907270075(30)
76
9907270076(27)
77
9907270077(24)
78
9907270078(21)
79
9907270079(18)
\Set Subnet\80..89
80
9907270080(15)
81
9907270081(12)
82
9907270082(09)
83
9907270083(06)
84
9907270084(03)
85
9907270085(97)
86
9907270086(94)
87
9907270087(91)
88
9907270088(88)
89
9907270089(85)
09.08.2010
SIUS AG (c) 2004
100 / 112
System\Hardware\Control unit
\Set Subnet\90..99
90
9907270090(82)
91
9907270091(79)
92
9907270092(76)
93
9907270093(73)
94
9907270094(70)
95
9907270095(67)
96
9907270096(64)
97
9907270097(61)
98
9907270098(58)
99
9907270099(55)
DeltaX
The absolute point of entry can be shifted in the horizontal direction. This can be used to compensate for assembly
inaccuracies.
X-0.1mm
to the left
99072800(76)
X+0.1mm
to the right
99072801(73)
X-1mm
to the left
99072802(70)
X+1mm
to the right
99072803(67)
X-10mm
to the left
99072804(64)
X+10mm
to the right
99072805(61)
09.08.2010
SIUS AG (c) 2004
101 / 112
System\Hardware\Control unit
DeltaY
The absolute point of entry can be shifted in the vertical direction. This can be used to compensate for assembly
inaccuracies.
Y-0.1mm
downwards
99072900(67)
Y+0.1mm
upwards
99072901(64)
Y-1mm
downwards
99072902(61)
Y+1mm
upwards
99072903(58)
Y-10mm
downwards
99072904(55)
Y+10mm
upwards
99072905(52)
Menu
The keyboard menu can be switched off. This is especially helpful when the configuration is to be used only via
the barcode reader. The barcode reader offers the advantage that the commands and programs permitted for the
user can be compiled on one sheet of paper.
Off
The keyboard menu is suppressed. Use of the
equipment is possible only via a barcode reader or a 99078000(93)
central computer.
On (Default)
The keyboard menu is switched on again. If the
menu is switched off, it can no longer be switched
99078001(90)
on via the keyboard. Normally it must be switched
on again by a barcode, from a central computer or
by means of a cold start. A further possibility is to
switch the menu on again by the code '282806'. The
code must be entered in one go on the transparency
keyboard. For this reason it should be made
available only to experienced persons.
Keystroke
Escape
9906442001(82)
Opt
9906442002(79)
Help
9906442003(76)
Next Window
9906442004(73)
09.08.2010
SIUS AG (c) 2004
102 / 112
System\Hardware\Control unit
Enter
9906442005(70)
Zoom
9906442006(67)
Menu
9906442007(64)
Match
9906442008(61)
Backspace
9906442009(58)
F1
9906441001(75)
F2
9906441002(72)
F3
9906441003(69)
F4
9906441004(66)
F5
9906441005(63)
Right
9906443001(89)
Up
9906443002(86)
Left
9906443003(83)
Down
9906443004(80)
Home
9906443005(77)
End
9906443006(74)
Page Up
9906443007(71)
09.08.2010
SIUS AG (c) 2004
103 / 112
System\Hardware\Control unit
Page Down
9906443008(68)
Insert
9906443009(65)
0 (Default)
9906440000(71)
1
9906440001(68)
2
9906440002(65)
3
9906440003(62)
4
9906440004(59)
5
9906440005(56)
6
9906440006(53)
7
9906440007(50)
8
9906440008(47)
9
9906440009(44)
Set Subnet
Sius AG devices communicate with one another via
the field bus LON. Each device has its own address. 99064000(92)
One part of this address is the so-called subnet. The
LON electronic measuring system and the control
unit with the same subnet always belong together.
Different lanes must be correspondingly
differentiated in the subnet. Every LON electronic
measuring system sends its own detected shots to
the control unit in the same subnet in which it is
itself addressed. A LON electronic measuring
system with subnet 5 sends its shots to the control
unit with subnet 5.
By setting a subnet on a control unit only the
address of the control unit is affected. A previously
linked LON electronic measuring system must be
reconnected after this alteration (please refer to
'\Hardware\Target\Connect' and instructions for use.
Insofar as a LON electronic measuring system is
located in the same subnet, the status of the control
unit changes from 'Offline' to 'Stop' or 'Ready'
09.08.2010
SIUS AG (c) 2004
104 / 112
System\Hardware\Control unit
according to whether a program is selected or not.
The subnet can be selected via the 10-er keyboard.
Pressing the Enter key confirms a given value. With
'Esc' the entry can be cancelled. The F5 key allows
incorrect entries to be corrected in time.
RC92
Optionally a RC92 (shoot box) can be connected to a control unit. The RC92 is controlled by means of three buttons
(Zoom, Menu and Shoot).
Match Menu
Via the Menu button an additional window can be opened on the screen. This window lists all the functions
available in the Control Menu. In this way the control unit can be remotely controlled by the firer without having to
leave his position.
In official ISSF contests the firer is not permitted to carry out these functions himself. It must therefore be possible
to switch off the Shoot Menu.
Off
The match menu is switched off. The Match button
on the RC92 has no function.
99079900(19)
On
The match menu is switched on.
99079901(16)
Short format
Only a reduced number of functions is available
(Clear Graphics).
99079902(13)
Target
Settings that must be communicated to the LON electronic measuring system are stored under '\Target'. These settings
are also frequently dependent on the program selected and therefore can be overwritten if necessary.
Target changer
Some detection systems are quipped with a target changer (S101, S310). Each target image has been
programmed with a basic setting or a shaft. If a program with a specific target is selected, the preselected shaft is
automatically activated. If the detection system is not equipped with a changing mechanism, the command is
ignored. If the target image is mounted in a different shaft or if the target image on the control unit does not
correspond to the physical target image, the shaft can be changed by means of the target changer commands.
The target image is hereby automatically programmed for the new choice of shaft. If the same program is selected
again later, the latest shaft to be selected will again be selected in any case.
A (Default)
The 'shaft' A corresponds to the fixed frame of the
detection system.
09907190(06)
B
The shaft B is the alternative frame.
09907191(03)
C
With the target S101 there are two alternative
frames available. The shaft C is the second
alternative frame.
09907192(97)
Sensitivity
The detection systems are fitted with various amplifier settings for the microphone. For most systems and
weapons a low sensitivity is the correct setting. In the 25 metre rapid fire pistols with a very small recoil are used.
The speed of the projectile is correspondingly small and the impact on the rubber very light. For these disciplines a
high sensitivity is necessary so that the shot can always be correctly picked up. But the setting must be set to high
only in these disciplines because with other firearms otherwise crosstalk onto neighbouring lines could ensue. The
setting is normally correctly adjusted for the programs and must not be adjusted manually.
\Sensitivity\Use Always
09.08.2010
SIUS AG (c) 2004
105 / 112
System\Hardware\Target
On
99072099(45)
Off (Default)
99072098(48)
Low (Default)
Low sensitivity is required for most bullets.
09907200(73)
High
High sensitivity is needed above all for sport
shooting (25m), which is shot with high recoil
weapons, typically on targets S10 and S25/50
09907201(70)
Paper feed
After every shot, detection systems controlling a materials handling unit (paper or rubber tape) trigger an automatic
feed unit. The feed unit is measured in millimetres. Depending on the discipline and the weapon, the tape must be
fed a greater or lesser distance. These distances are laid down in the target images. But every discipline can
define its own actual setting values. The tape feed for a 10 metre discipline is 20 millimetres. In ISSF finals the
feed distance is increased to 30 millimetres. The tape feed can be changed after a program has been selected.
\Paper feed\Use Always
On
99077899(08)
Off (Default)
99077898(11)
0
mm
99077800(14)
1
mm
99077801(11)
2
mm
99077802(08)
3
mm
99077803(05)
4
mm
99077804(02)
5
mm
99077805(96)
10
mm
99077810(81)
20 (Default)
mm
99077820(51)
09.08.2010
SIUS AG (c) 2004
106 / 112
System\Hardware\Target
30
mm
99077830(21)
40
mm
99077840(88)
50
mm
99077850(58)
Connect
This barcode switches the control unit over to a
special configuration mode. The control unit waits
99063200(67)
for a service PIN message from any LON electronic
measuring system. This message can be created on
the LON electronic measuring system, either when
the service PIN is pressed or when shooting takes
place. But a shot triggers a Service PIN message
only if the LON electronic measuring system was not
previously configured. Every LON electronic
measuring system that first reports this Service PIN
message is reprogrammed by the control unit to its
own subnet address. This function is used only if the
LON electronic measuring system does not have its
own LNR (lane number box).
Distance Index
0 (Default)
99081200(96)
1
99081201(93)
2
99081202(90)
3
99081203(87)
4
99081204(84)
Time Control Unit
Time Control Unit
Off (Default)
99080300(80)
On
99080301(77)
Duel mode
09.08.2010
SIUS AG (c) 2004
107 / 112
System\Hardware\Time Control Unit
Off (Default)
99080400(71)
On
99080401(68)
Graphic Printer Model
Undefined Printer (Default)
99080500(62)
D931-SP
99080501(59)
D931
99080502(56)
iDP3240
99080503(53)
Shot sensor
The shot sensor allows cross shots and no scores to be detected. Without the shot sensor all shots are interpreted as
own shots on the own target. Even a shot from a neighbouring lane onto the own target is interpreted as an own shot
and included in the calculation of the results. With the shot sensor, within a certain timescale after the Shot Off signal the
corresponding Shot On signal must be produced. If only a Shot Off signal is produced, the firer has not hit the target. The
shot sensor can be connected to the control unit as an optional extra. At the moment when the control unit recognises
the shot sensor, it switches this on automatically. If the shot sensor is removed, the control unit recognises this after a
short period of time and automatically switches the shot sensor off again.
Off
On installations without a shot logoff, this setting will
be switched off automatically. It is possible to switch
off the shot logoff manually even though it is
connected.
09907010(61)
On (Default)
The setting shot logoff ON is automatically cancelled
if no shot logoff is connected.
09907011(58)
09.08.2010
SIUS AG (c) 2004
108 / 112
Logon
Logon
In order that the system can adhere to the necessary rules, under certain circumstances particular information about the firer and his
weapon is needed. All this information can be recorded under the section 'Registration'.
Info
Requirements
With set assumptions the system requires information about weapon, position and/or firer number before a group can be
loaded. As long as this information is missing the group cannot be input.
Legalisation
If a legalisation unequal to 0 is chosen, then both the practice and the firer must produce the same legalisation in
their codes in order for it to be authorised. The legalisation of the firer is however only active if the firer number is
requested at the same time. This command is not to be confused with the command firer legalisation, under which
the legalisation of the firer can explicitly be provided. Fact: the settings '\Requirements\Legalisation' and
'\Register\Legalisation' must agree or one or other must be set to 0 in order that a program can be started and
shooting can take place.
0 (Default)
No legalisation is required.
99077000(86)
1
Demanded legalisation
99077001(83)
2
Demanded legalisation
99077002(80)
3
Demanded legalisation
99077003(77)
4
Demanded legalisation
99077004(74)
5
Demanded legalisation
99077005(71)
6
Demanded legalisation
99077006(68)
7
Demanded legalisation
99077007(65)
8
Demanded legalisation
99077008(62)
9
Demanded legalisation
99077009(59)
Weapon required
In order that in contests it can be determined which program was shot with which weapon, it is possible to force
the setting 'Position required'. Before a program can be loaded, a weapon type must be declared.
Off (Default)
Weapon identification is optional.
99077300(59)
09.08.2010
SIUS AG (c) 2004
109 / 112
Logon\Info\Requirements
On
A weapon specification must be input before a
program can be selected.
99077301(56)
Position required
In order that in contests it can be determined which program was shot in which position, it is possible to force the
setting 'Position required'. Before a program can be loaded, a position must be declared.
Off (Default)
Reporting of position is optional.
99077200(68)
On
A position report must be input before a program
can be selected.
99077201(65)
Firer number required
The firer number identifies the firer (see also '\Registering\Firer number'.
Off (Default)
The firer number is optional.
99077400(50)
On
A firer number must be input before a program can
be selected.
99077401(47)
Legalisation
Legalisation can be loaded either individually or together with a firer number practice code. The firer must as a result input his
firer number first (inclusive of legalisation) and then a program. Only when both legalisations agree, or one or other has a zero
value, can the program be launched. Otherwise the screen gives the error message 'Wrong legalisation'. A firer in possession
of the legalisation 0 in his practice code can shoot all programs, and a program that shows a legalisation 0 can be shot by all
firers.
0 (Default)
Legalisation of the firer
99077700(23)
1
Legalisation of the firer
99077701(20)
2
Legalisation of the firer
99077702(17)
3
Legalisation of the firer
99077703(14)
4
Legalisation of the firer
99077704(11)
5
Legalisation of the firer
99077705(08)
6
Legalisation of the firer
99077706(05)
7
Legalisation of the firer
99077707(02)
09.08.2010
SIUS AG (c) 2004
110 / 112
Logon\Legalisation\8
8
Legalisation of the firer
99077708(96)
9
Legalisation of the firer
99077709(93)
Weapon Type
For the assessment of a contest, it can be important that the type of weapon used in a program that has been shot is known,
for example if various rank listings are to be established for storm rifle 90 and storm rifle 57. In such a case the weapon type
can be set. With the setting '\Requirements\Weapon type' the specification of a weapon type can be insisted upon before a
program can be installed. Otherwise the program would be declined with a message 'weapon type needed'. The weapon type
selected is displayed on the screen and on the paper printout.
Off (Default)
99076800(07)
Rifle
99076801(04)
Free Rifle
99076821(41)
Carbine
99076802(01)
Stgw 57
99076803(95)
Stgw 90
99076804(92)
Free Pistol
99076805(89)
Sport Pistol
99076806(86)
Sport Pistol Big Bore
99076807(83)
Sport Pistol Small Bore
99076808(80)
Ordnance pistol
99076809(77)
Ordnance pistol 75
99076810(74)
Position
For the assessment of a contest, it can be important that the position in which shooting took place is known. In such a case the
position can be input either on the menu or via a barcode. With the setting '\Requirements\Position' the specification of a
position can be insisted upon before a program can be installed. The position selected is displayed on the screen and on the
paper printout.
09.08.2010
SIUS AG (c) 2004
111 / 112
Logon\Position\Off
Off (Default)
99077600(32)
Prone
99077601(29)
Prone supported
99077604(20)
Kneeling
99077603(23)
Standing
99077602(26)
Firer number
The firer number identifies the firer. The firer number
can also be loaded via a barcode (Sius barcode
99063900(04)
inclusive of legalisation or SSV licence card) or via
the keyboard. The firer number is transferred to the
central processor. From the central processor the
name of the firer can be construed from the firer
number. The firer number is displayed on the screen
and on the printer.
Should the setting Firer number needed' be
activated and 'Repeat allowed' be switched off, then
the firer number is erased after each program. This
ensures that with this configuration before every
program a firer number must be introduced.
09.08.2010
SIUS AG (c) 2004
112 / 112
Abkürzungen:
Shortcuts
1
10
Moose
2
2x30
Rifle 2x30
3
3*10
3*10
3*20
3*40
30
Air Rifle 3*10
Rifle 3*10
Standard Rifle 3*20
Free Rifle 3*40
Rifle 30
5
5
Moose 5-5-4-3
6
60
60
600
Free Rifle 60
Rifle 60
Scale Factor (600)
A
A1
A10
A101
A102
A103
A10m
A10m
A2
A20m
A3
A4
A5
A-5m
A6
A7
A8
Abrt
Act
Act
AdjC
Admn
Advn
MG Ziel A1
Precision
A10 100m
A10 200m
A10 300m
Pistol A 10m
Rifle A 10m vertical
MG Ziel A2
Rifle A 20m vertical
MG Ziel A3
MG Ziel A4
MG Ziel A5
Pistol A 5m
MG Ziel A6
MG Ziel A7
MG Ziel A8
Abort
MPI
SCB
Adjust Clock
Administrator
Advanced
Air
Allo
AP20
AP40
AP60
APis
AR20
AR30
AR40
AR60
ARif
AUT
Auto
Air pressure weapons
Allowable
Air Pistol 20
Air Pistol 40
Air Pistol 60
Air Pistol
Air Rifle 20
Air Rifle 30
Air Rifle 40
Air Rifle 60
Air Rifle
Austria
Startup program
B
B1
B1
B10m
B10m
B2
B2
B20m
B3
B3
B4
B5
B-5m
B6
B7
B8
BesS
BFrn
Biat
BigB
BLft
BO10
BO20
Boar
Boar
Boar
Both
Brcd
BRgt
Bersaglio 1
MG Ziel B1
Pistol B 10m
Rifle B 10m horizontal
Bersaglio 2
MG Ziel B2
Rifle B 20m horizontal
Bersaglio 9
MG Ziel B3
MG Ziel B4
MG Ziel B5
Pistol B 5m
MG Ziel B6
MG Ziel B7
MG Ziel B8
Best shot
Bear
Biathlon
Big Bore
Bear Left
Rifle B 10m ellipse
Rifle B 20m ellipse
Wild Boar 2
Wild Boar 5
Wild Boar 5 Right
On Both
Edit Barcode
Bear Right
C
C1
MG Ziel C1
C15m Pistol C 15m
Abkürzungen:
Shortcuts
C15m
C2
C3
C30m
C4
C5
C6
C7
C-7m
C8
Cal
Cal
Calf
CAll
CAll
Carb
Catg
CFP
CGaS
Cham
Chmp
Clas
Clck
Clmn
Clr
ClrG
ClrL
Clss
Cmbn
Cmpl
Cnct
Cntr
Comp
ConB
Conf
ConL
Crcl
CroA
Cros
CrSh
CtMo
CtmS
CU
CU
CURs
D
Rifle C 15m
MG Ziel C2
MG Ziel C3
Rifle C 30m
MG Ziel C4
MG Ziel C5
MG Ziel C6
MG Ziel C7
Pistol C 7m
MG Ziel C8
Calibre
Display calibre
Moose Calf
Pistol C All
Rifle C All
Carbine
Category
Center Fire Pistol
Clear target after shots
Chamois
Swedish championship
Classic
Time
Column Configuration
Clear
Clear target window
Clear List
Classes
Combined
Complete
Connect
Control
Compute series
Convert both sighters
Confirm
Convert last sighting shot
Circle
Croatian AR Target
Cross
Cross Shot
Control Mode
Customer Settings
Control unit
On-screen
Control unit reset
D100
D10m
D15m
D200
D300
D40m
D-5m
DAll
DAN
Dbl
Debg
Debg
Defe
DeMo
Dflt
Dfrd
DisF
Disp
Dist
Dist
Divi
D-SP
Duel
DFS100
Pistol D 10m
DFS 15m
DFS 200
DFS 300
Rifle D 40m
Pistol D 5m
Rifle D All
Dansk
Double
Debug
Debug Mode
Deferred Shots
Demonstration Mode
Default
Deferred
Screen-format
Screen
Distance
Distance Index
Divisions
D931-SP
Duel mode
E
E20m
EAll
Emty
EnAR
ENG
ERpt
ESP
Euro
EurS
Pistol E 20m
Pistol E All
Empty
Enable Autoreset
English
Enable Repeat
Español
European
European with Seconds
F
FacS
FB
Fig1
Fig2
Fig3
Fig8
Fill
FldA
FldB
FldD
Fltr
Factory Settings
Full Bore
Full Figure
Half Figure
One Third Figure
Eighth figure
Fill Series
Field A
Field B
Field D
Filter
Abkürzungen:
Shortcuts
Fnal
FncK
Foot
FRA
Free
Free
Free
FRes
Frmt
FrNo
FrNo
Frst
Func
Final
Function Keys
Footer
Francais
Free Rifle
Free Series
Free series start setting
Final reserved
Date format
Firer number
Firer number required
First relay
Function
G
GC
GER
GrGr
GrKl
GrLi
Grp
GrRe
Group championship
Deutsch
Gross Gross
Gross Klein
Gross links
Group
Gross rechts
H
HH+
Head
hGms
Hnt
Hnt
HrdC
HrdW
hRoe
Hwal
Hour minus 1
Hour plus 1
Header
Chamois Hubertus
Belgium
Hunting
Print screen
Hardware
Roe Left
Hans Waldmann
Schiessen
I
IDP3
Ilgl
IncS
Indi
Ins0
InTn
Invr
InvS
ITA
iDP3240
Illegal Shot
Include sighters
Indication
Insert zero shot
Display Inner ten
Inverse
Invalid shots
Italiano
K
KlGr
KlKl
KlLi
KlRe
Knbn
Knee
Kybd
Klein Gross
Klein Klein
Klein links
Klein rechts
Knabenschiessen
Kneeling
Keyboard
L
Lang
Layt
LCD
Legl
LFed
LfLw
Locl
LogH
Logn
LSht
LSW
Language
Layout
On LCD
Legalisation
Line feed
Large font in Listwindow
Local
Log Hex
Logon
Last Shot
Last Shot Window
M
M1
M2
M3
MalF
Mddl
Menu
MinMin+
Mntn
MonMon+
Moos
Morg
MP20
MP30
Msg
Mtch
2x1/3 figure
1/1+1/3 figure
1/8+1/2 figure
Malfunction
Middle relay
Match Menu
Minute minus 1
Minute plus 1
Maintenance
Month minus 1
Month plus 1
Running Moose
Morgarten
Pentathlon 20
Pentathlon 3*10
Message
Match
N
N15m NSF 15m
NAMf Non-Allowable
No
Number
Abkürzungen:
Shortcuts
No
NoLf
NOR
NOR
NrOI
NSwe
NTC4
NTC5
NxtP
NxtS
SNr Prim
Number of line feeds
Norsk
Norway
Number of Instancies diff
New Swedish target
NTTC4
NTTC5
Next Primary Score
Next Secondary Score
O
Off
Oly1
Oly2
OP_A
OP_B
OPAS
OPBS
OpnS
Or75
OrdP
Othr
Graphic Printer Model
On printer
Print
Printing
Report Processes
Programs
Swedish program
Prone
Print Overtime
Print Protocol
R
0
Oly100
Oly200
OP Part 1
OP Part 2
OP A5 Sighters
OP B4 Sighters
Opening shooting
Ordnance pistol 75
Ordnance pistol
Other
P
P60
PA00
Para
PB00
Pent
PFed
PffW
PiBB
PiBB
PiSB
Pist
Pist
Pos
Pos
PPrW
PrCo
Prct
Prec
Pres
Prim
PrnF
PrnF
Prnt
Prnt
Prnt
Prnt
Proc
Prog
Prog
Pron
PrOT
Prot
Pistol 60
PA100
Parameter
PB100
Pentathlon
Paper feed
Pfäffiker winter practice
Big bore pistol
Sport Pistol Big Bore
Sport Pistol Small Bore
Free Pistol
Pistol
Position
Position required
Practice progress window
Practice Control
Practice
Precision
Presentation
Primary
Print-format
Prone supported
R BC
RapF
Repo
Repo
Rept
Requ
Res
RF3x
RFP
RFPM
RFPW
Activate remote barcode
Rapid Fire
Report Shot Counter
Reports
Repeat
Requirements
Reserved
Rapid Fire 3x20
Rapid Fire Pistol
Military Rapid Fire Men
Military Rapid Fire
Women
Rght Right
Rifl
Rifle
RLd
Reload
Rmot Remote
Rmov Remove Timer
Roeb Running Roebuck
Rprn Reprint
Rset Reset
Rset Reset Shot Counter
Rset Reset Timer
RsNo Reset Shot Number
Run
Running Target
Rus
Russian
S
Save
SbyS
SCB
SclF
Scnd
ScNI
Scor
Save Customer Settings
Shot by Shot
Simulator SCB
Scale Factor
Scandinavia
Save number of
instancies
Score
Abkürzungen:
Shortcuts
SCPr
ScrB
Sec
Sec0
SecS
SeCt
Sens
SeqN
SetS
SetS
Sett
Sett
Sg57
Sg90
Shoo
Show
Shrt
Shrt
ShtC
Shts
Sigh
SiSe
SjF4
SjF5
SjFK
SjFS
SlfT
SmlB
SpPi
SSns
Stat
Stnd
Stnd
StPi
StpL
Strt
SubT
Sui
SWE
SWE
Symb
Sys
SC-Programs
Scoreboard
SNr Prim Sec
Set second zero
Secondary Score
Settings Control
Sensitivity
Total with SeqNr
Set Scale Factor
Set Subnet
Set Timer
Settings
Stgw 57
Stgw 90
Shoot
Display Messages
Short
Short format
Shot Counter
Shoot
Sighters
Single Execution
Schijf 4
Schijf 5
Schijf K
Schijf S
Self Test
Small Bore
Sport Pistol
Shot sensor
Status flashing
Standard
Standing
Standard Pistol
Stop at Left
Start Timer
Subtotal
Switzerland
Moose SWE
Svenska
Symbol
System
T
t xy
t x/y
TChg Target changer
TCU Time Control Unit
TgAl
TgFM
TgNm
Tgts
ThiC
Timr
Timr
TOTL
Trgt
Trgt
Target Alternative
Target Feed Message
Display target name
Targets
Thin Cross
Programed Timers
Timer
TOTAL
Target
Target test
U
UsrG User Group
USSe US+Seconds
V
Voeg
Vögelinsegg
W
Weap Weapon
Weap Weapon required
Weap Weapon Type
X
X
X+01
X+1
X+10
X-01
X-1
X-10
XY
DeltaX
X+0.1mm
X+1mm
X+10mm
X-0.1mm
X-1mm
X-10mm
Spread
Y
Y
YY+
Y+01
Y+1
Y+10
Y-01
Y-1
Y-10
Z
DeltaY
Year minus 1
Year plus 1
Y+0.1mm
Y+1mm
Y+10mm
Y-0.1mm
Y-1mm
Y-10mm
Abkürzungen:
Shortcuts
Zi30
Zimmerstutzen 30
INSTRUKTION VID SKJUTPLATS
1.
Slå på spänningen
2.
Tavlan kommer fram på monitorn
3.
Skjut provskotten [P]
4.
Tryck Match på fjärrkontrollen eller kontrollenheten när du är klar
med provskotten [S]. (D är dold skjutning där skotten inte visas förrän
omgången är klar och skytten trycker på Visa)
5.
När du är klar med tävlingsskotten tryck på TOTAL för att avsluta.
Ny skjutning?
Tryck på Repetera
(finns i menyn via fjärrkontrollen eller på kontrollenheten).
1 (1)
d okumentegenskap .
INSTRUKTION FÖR SKJUTLEDAREN
SIMULERA SKJUTNING MED DEMOSKOTT
Dok-nr: XNA 250108
Datum: 2011-08-18
d okumentegenskap .
1. Välj:
Home sedan System\Inställningar\Övrigt\Demo\På
2. För att simulera skott tryck på ”INS” (0).
3. Utropstecknet efter skottets valör anger att skottet
är simulerat.
d okumentegenskap .
INSTRUKTION FÖR SKJUTLEDAREN
HUR GÖRA OM NÅGON ÄNDRAT PÅ INSTÄLLNINGARNA
I KONTROLLENHETEN
Dok-nr: XNA 250110
Datum: 2011-08-18
d okumentegenskap .
1. Gör markeringssystemet spänningslöst.
2. Stoppa in en smal pinne (exempelvis en popnit) i
det översta hålet av de båda små hål som finns
ungefär i mitten på kontrollenhetens baksida, vid
kontakterna. (Bakom plåten finns nämligen en liten
kontakt fastsatt på ett kretskort, så var försiktig).
3. Håll kvar pinnen, slå på nätspänningen. Efter ca 15
s hörs en ton från kontrollenheten. En text kommer
upp på bildskärmen (Kundinställningar åter…). Ta
ur pinnen.
4. Därmed har de sparade kundinställningarna
återhämtats och kontrollenheten fungerar som
tidigare.
Ändra kontrollenheter och SiusData från
10 m till 50 m eller tvärtom!
1. Klicka på ikonen Funktionstangenter i SiusData.
2. Klicka på Import.
3. Välj filen Functions2_konfigurering_50m.ini när du ställer om till 50m
eller Functions2_konfigurering_10m.ini för 10m, filerna finns i mappen
SiusData. När filen är markerad tryck på Öppna.
4. Tryck på OK.
5. Gör samtliga tavlor ”aktiva” dvs. gröna.
2013-03-05
6.Klicka på knapparna 1 – 4 i ordning, vänta ca 30s mellan knapp
tryckningarna. När ni har klickat på knapp 4 kommer ett pip att höras
från kontrollenheten.
7. Klicka på ikonen Funktionstangenter i SiusData.
8. Klicka på Import.
9. Välj filen Functions2_Tävling.ini.
Klicka på Öppna.
10. Tryck på OK.
11. Klicka på ikonen ”allmänna inställningar”
12. Vid bantyp välj för 50m.
Eller för 10m välj
13. Klart.
Vi påminner om nya programmen för ISSF tävlingar som finns på vår
hemsida www.sius.se under Nyheter – Sport.
2013-03-05
1.
Introduktion
1
2.
Hämtning av dokument och programvara
2
3.
Kontrollera mjukvaruversion
3
4.
Installation LonDongle
4
5.
Reset LonDongle
5
6.
Installation SiusData
6
7.
Uppgradering SiusData
7
8.
Installation och uppgradering SiusView
8
8.
Uppgradering mjukvara i kontrollenhet och
tavla
9
10. Registrering av skyttar i SiusData
10
11. SiusData vid tävling
11
12. Skapa skott i simuleringsmod SiusData
12
13. SC-Program
13
14. Underhåll tavla S10
14
15. Underhåll tavla S25/50
15
16. Felrapport
16
17. Förklaring av csv fil
17
18. Error navigator
18
19
20
www.sius.se
UTBILDNING
SA941
Elektroniskt markeringssystem
2011-02-06
Introduktion
Målsättningen för utbildningen är att ge nödvändig kunskap för att använda och
underhålla SIUS anläggningar samt att kunna genomföra tävlingar med
resultatredovisning och publikinformation med utnyttjande av systemets möjligheter.
Utbildningen omfattar:

Grundläggande information om tekniken

Underhåll och service

Problembestämning

Resultatredovisning med PC-programmet Shooter och SIUS systemet

Uppgradering av programvara
Sida 2 av 2
Hämtning av
dokument och
programvaror
www.sius.se
Hämtning av dokument och programvaror
INSTRUKTION
Dok. nr: XNA 250155
•
Gå till hemsida: www.sius.se
Datum: 2011-02-05
Sidan: 2 av 3
Hämtning av dokument och programvaror
INSTRUKTION
Dok. nr: XNA 250155
Datum: 2011-02-05
Sidan: 3 av 3
Kontrollera
mjukvaruversion
www.sius.se
Kontrollera mjukvaruversion
INSTRUKTION
Dok. nr: XNA 250151
Datum: 2011-02-05
Sidan: 2 av 2
För att se vilken version av mjukvaran man har gör som nedan.
•
Detta gäller för SiusData & SiusView
•
Klicka på ”frågetecknet”
•
Klicka på Om
•
Här ser man versionen
Installation
LON DONGEL
www.sius.se
INSTALLATION LONDONGEL
INSTRUKTION
Dok. nr: XNA 250154
Datum: 2011-02-05
Sidan: 2 av 3
OBS! Anslut INTE LonDongeln till datorn innan SiusData är
installerad
1.
2.
Anslut USB kontakten till datorn, när bilden nedan kommer upp välj Nej inte den
här gången klicka på Nästa
Välj som på bilden nedan, klicka på nästa
INSTALLATION LONDONGEL
INSTRUKTION
Dok. nr: XNA 250154
Datum: 2011-02-05
3.
Markera Sök igenom flyttbar media …………. Klicka på Nästa
4.
Klicka på Slutför, detta kommer att ske två gånger
Sidan: 3 av 3
Installaton SIUS SNI
1. Anslut Sius SNI till datorn
2. Öppna Kontrollpanelen ->System ->Enhetshanteraren
3. Högerklicka på Sius Network Interface välj egenskaper välj uppdatera drivrutin
4. Välj det markerade alternativet
5. Leta rät på mappen SNI på CD;n ock klicka på nästa
6. Klicka på installera
7. Sius SNI är nu klar att använda
2
Reset
LonDongle
www.sius.se
Reset LonDongle
INSTRUKTION
Dok. nr: XNA 250150
Datum: 2011-02-05
Sidan: 2 av 4
Om du inte får kontakt med banan kontrollera att lysdioderna lyser
som på bilden nedan.
Om de inte lyser som bilden visar utan de istället lyser gult gör reset
på Lon Dongeln enligt följande:
•
•
•
Öppna kontrollpanelen
Klicka på system
Klicka på fliken Maskinvara
Reset LonDongle
INSTRUKTION
Dok. nr: XNA 250150
Datum: 2011-02-05
•
Välj
•
Klicka på ”pluset” vid XLON
•
Högerklicka på Egenskaper
Sidan: 3 av 4
Reset LonDongle
INSTRUKTION
Dok. nr: XNA 250150
•
Klicka på reboot
•
..
Datum: 2011-02-05
Sidan: 4 av 4
Installation och
konfigurering av
Sius Data
www.sius.se
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 2 av 12
1. Leta reda på mappen SiusData på cd:n och klicka på filen
Setup.exe
2. Välj installations språk
3. Klicka på OK
4. Om SiusData skall installeras på en dator med XPoperativsystem klicka nästa
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 3 av 12
5. Om SiusData skall installeras på en dator med Vista eller
Windows 7 ändra så att programmet installeras på C:\Sius
Ascor\SiusData
6. Klicka på Nästa
7. Klicka på Nej
8. När installationen är klar starta SiusData genom att klicka på
ikonen på skrivbordet
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
9. Välj Svenska klicka på OK
10. Klicka på OK
11. Välj CtmShoot2_75a_Main.ini eller senare version
12. Välj Functions2_Empty.ini klicka på OK
Sidan: 4 av 12
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
13. Markera XLon USB skriv in antalet tavlor
14. Klicka OK
15. Klicka Avsluta
16. Starta SiusData från skrivbordet
Sidan: 5 av 12
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 6 av 12
17. Markera det översta alternativet ”Öppna ny Tävling….”
18. Klicka OK
19. Skriv in Licensnumret för Lon Dongeln (är tryckt på Lon
Dongeln)
20. Klicka på ikonen Allmänna inställningar
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 7 av 12
21. Under bantyp välj “Air pressure weapons”
22. Fliken fjärrkontroll, välj inställningar som nedan
23. Fliken Data backup, om SHOOTER skall användas som
resultatsystem skapa en mapp rakt under C:\ och kalla den ex.
resultat (C:\resultat) klicka sedan på Lägg till
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 8 av 12
24. Välj mappen resultat som skapades i punkten ovan, klicka på
OK
25. Fliken ”Visa tavlor” välj inställningar som nedan
26. Kopiera filerna ” Functions2_10M.ini” och ”
Functions2_konfig10M.ini” samt ”CustomerBarcodes.txt”
från Cd:n till mappen SiusData på datorn
27. Kopiera alla bitmap ikoner från mappen bitmappikoner på
Cd:n till mappen SiusData
28. Klicka på ikonen Funktionstangenter
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 9 av 12
29. Klicka på import
30. Markera filen ” Functions2_konfigurering_10M.ini” klicka på
öppna
31. Gör samtliga banor ”aktiva” genom att klicka på den gråa
rutan för varje bana så att den blir grön
32. Klicka på funktionstangenterna i ordning 1 till 4 vänta ca
30sek mellan knapptryckningarna efter man tryckt på knapp
fyra kommer ett pip att höra från kontrollenheten vilket
innebär att anpassningen är sparad.
till
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 10 av 12
33. Klicka på ikonen Funktionstangenter
34. Klicka på Import
35. Markera filen ” Functions2_Tävling.ini” klicka på öppna
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 11 av 12
36. Klicka på OK dessa funktionstangenter används för att ställa
in fjärrkontrollen, radering av grafiken samt Match knapp vid
ex. finaler
37. Klicka på ikonen ”Anpassa verktygsrad”
38. Denna funktion används för att begränsa antalet ikoner i
verktygsraden, markera den som skall tas bort och tryck på
<<Ta bort
39. Detta är en lämplig uppsättning ikoner
40. Klicka på ikonen ”skrivarinställningar”
Installation och konfigurering av SiusData
INSTRUKTION
Dok. nr: XNA 250153
Datum: 2013-03-19
Sidan: 12 av 12
41. Detta är en lämplig inställning för utskriften av
skjutprotokoll, under Text1 skriver ni in tävlingens namn
Uppgradering av
Sius Data
www.sius.se
Uppgradering av Sius Data
INSTRUKTION
Dok. nr: XNA 250144
•
•
Datum: 2011-02-05
Sidan: 2 av 4
Kopiera hela mappen C:\Program\SiusAscor\SiusData till ex.
C:\temp
Stäng SiusFtpServer genom att högerklicka på den och välj
•
Hämta uppgraderingen från www.sius.se ► Programvaror
•
Unzip filen SiusData_Update.zip
•
Klicka på filen setup.exe
•
Klicka på Kör, klicka på OK för språkval Svenska. Klicka på
OK för bekräftning borttagning av fil
•
Uppgradering av Sius Data
INSTRUKTION
Dok. nr: XNA 250144
Datum: 2011-02-05
•
Klicka på filen setup.exe igen.
•
Klicka på OK
•
Klicka på Nästa
•
Svara Nej.
Sidan: 3 av 4
Uppgradering av Sius Data
INSTRUKTION
Dok. nr: XNA 250144
•
Datum: 2011-02-05
Sidan: 4 av 4
Starta SiusFtpSever genom att klicka på den i mappen
C:\Program\SiusAscor\SiusData
•
Från den gamla SiusData som ni sparade tidigare (C:\temp)
kopiera filerna RCI.ini, siusdata.ini, SCPrograms_10.ini,
Functions2_konfig10M.ini, Functions2_10M.ini
CustomerBarcodes.txt samt alla *.bmp filer.
•
Starta SiusData
•
•
Om inte skyttar vars namn innehåller (ÅÄÖ) inte visas rätt på
monitorn kontrollera filen RCI.ini, det skall stå som nedan
AsciiConversion = 0
Skrivskydda filen efter den sparats
Installation &
uppgradering
Sius View
www.sius.se
INSTALLATION SIUS VIEW
INSTRUKTION
Dok. nr: XNA 250152
Datum: 2011-02-05
Sidan: 2 av 6
Installation och konfigurering av Sius View
1. Leta rätt på filen Setup.exe på cd;n och klicka på den
2. Klicka OK
3. Om SiusView skall installeras på en dator med XPoperativsystem klicka nästa
4. Om programmet skall installeras på en dator med Vista eller
Windovs 7 ändra så att programmet installeras på C:\Sius
Ascor\SiusView
INSTALLATION SIUS VIEW
INSTRUKTION
Dok. nr: XNA 250152
Datum: 2011-02-05
5. Klicka på Nästa
6. Klicka på Slutför, programmet är nu installerat
7. Starta programmet med ikon på skrivbordet
8. Välj språk Svenska och tryck OK
Sidan: 3 av 6
INSTALLATION SIUS VIEW
INSTRUKTION
Dok. nr: XNA 250152
Datum: 2011-02-05
Sidan: 4 av 6
9. Skriv in IP-adress till datorn som SiusData körs på och tryck
på Nästa
10. Bocka i Aktivera och skriv in IP-adress till datorn som
SiusData körs på och tryck på Nästa
11. Klicka på ikonen Gemensamma inst.
12. Klicka på Ändra och markera med musen antalet banor
INSTALLATION SIUS VIEW
INSTRUKTION
Dok. nr: XNA 250152
Datum: 2011-02-05
13. I fliken Översikt tavla klicka på Flera tavlor
14. Detta är lämpliga inställning för visning
15. Starta om programmet för att inställningarna skall gälla
Sidan: 5 av 6
INSTALLATION SIUS VIEW
INSTRUKTION
Dok. nr: XNA 250152
Datum: 2011-02-05
Sidan: 6 av 6
Uppgradering:
•
Kopiera mappen SiusView till ex. C:\temp
•
Kör installationsprogrammet två gånger (första gången raderas
programmet)
•
När installationen är klar kopiera filen auxmon.ini
(konfigureringsinställningar) från den gamla versionen av SiusView som
ni sparade i första punkten till C:\Program\Sius Ascor\Siusview
Uppgradering av tavla och kontrollenhet
Ladda ner senaste versionen av mjukvaran från:
www.sius.se ► Programvaror
Klicka på Update, välj spara fil till ex. C:\temp
Filen är zippad, öppna den genom att klicka på den tills den är unzippad.
Klicka på Lon Org
Under mappen LmeLon kopiera filen LME_20p.NXE (eller senare)
till C:\Program\Sius Ascor\LonOrg\Download\LmeLon
Under mappen Me68000 kopiera filen
ME931_System_75a_Main_SWEDISH.68k (eller senare)
till C:\Program\Sius Ascor\LonOrg\Download\Me68000
Under mappen NIOS kopiera filerna NIOS_LS10_10i.flash eller nyare och
NIOS_HS10-Sport_11e. Flash eller nyare
Starta LonOrganizer
Klicka på ikonen Common
Kontrollera att det står XLon USB vid PC Lon alt. SIUS NetvorkInterface
annars ändra
Ändra denna inställning till 2sek
Välj Download och flik ME931
Klicka på
då söks efter installerade kontrollenheter
Klicka på knappen Refresh
då kommer kontrollenhetens programversioner att visas.
Klicka på File vid Download (68000)
Välj den senaste filen i detta fall ME931_System_75d_Main_SWEDISH.68k
Klicka på OK
Bryt spänningen till banorna vänta 10sek. slå på spänningen
till banorna, klicka på Start när bilden på monitorn blir randig
Nerladdningen till kontrollenheten startar tar ca. 20 min under nerladdningen
kommer bilden på monitorn att ”rulla”
När nerladdningen är klar klicka på Refresh och kontrollera att versionen är den rätta.
Uppgraderingen till tavlor under LME fliken och under
fliken NIOS för HS och LS tavlorna sker på samma sätt
men man behöver inte starta om banan innan nerladdningen
Efter att nerladdningen är klar starta om banan
Nu måste kontrollenheten konfigureras för språk, avstånd mm.
Se instruction Installation SiusData
För att slutföra installationen skall även nya filer kopieras till SiusData
Kopiera filerna från mappen System7_Main_Update\Main till mappen där SiusData finns
Instruktion för
registrering av
skyttar i Sius Data
www.sius.se
INSTRUKTION FÖR REGISTRERING AV SKYTTAR I SIUS DATA
INSTRUKTION
Dok. nr: XNA 250133
Datum: 2011-02-05
Sidan: 2 av 4
Instruktion för registrering av skyttar i
Sius Data.
Det finns två sätt för att registrera skyttar för användande i
SiusData, ett som används vid träning för att få namn på
utskrift och ev. kontrollremsa och ett vid tävling.
1. Träning
I SiusData klicka på ikonen ”Visa skyttar”
,klicka på
knappen Infoga.
Fyll i StartNr ex.1 på första skytten och Namn och Klubb. För
nästa skytt fyll i startnummer 2 Namn och Klubb o.s.v.
Spara filen när alla skyttar är registrerade genom att klicka på
knappen Export. Svara OK på frågan om sortering. Välj lämpligt
filnamn ex. föreningens namn och lämplig mapp ex.
C:\PROGRAM\SIUS ASCOR\SIUSDATA.
OBS!! Glöm inte att spara filen genom att klicka på export
annars är registreringarna borta.
När man startar en träning så skall man importera samma fil
som man skapade ovan genom att klicka på ikonen Visa
skyttarna och sedan på import och väljer den fil som ni sparade
ex. Västerås.csv.
INSTRUKTION FÖR REGISTRERING AV SKYTTAR I SIUS DATA
INSTRUKTION
Dok. nr: XNA 250133
Datum: 2011-02-05
Sidan: 3 av 4
För att välja skytt för resp. tavla klicka på den gula ikonen före
namnet och välj skytt i listan (sorteras på förnamn)
Välj önskat skjutprogram
Sänd till skyttens namn samt skjutprogram till monitorn genom
att klicka på den gröna pilen
2. Tävling:
Vid tävlingar, om inte externt resultat program används ex.
Shooter, kan man använda en Excel fil
(SiusDataResultatMacro) för registrering av skjutlag samt
insamling av resultat.
Skriv in Startnummer, Namn och Förening klicka på det lilla
”plusset”
INSTRUKTION FÖR REGISTRERING AV SKYTTAR I SIUS DATA
INSTRUKTION
Dok. nr: XNA 250133
Datum: 2011-02-05
Sidan: 4 av 4
Skriv in tavelnummer och skjutlag i respektive fält.
Klicka på minustecknet för att ”stänga” sidan.
Klicka sedan på ikonen Exportera skyttar.
För att välja skytt för resp. tavla klicka på den gula ikonen före
namnet och välj skytt i listan (sorteras på förnamn)
Välj önskat skjutprogram
Sänd skyttens namn samt skjutprogram till monitorn genom att
klicka på den gröna pilen, rutan i kolumnen ”ctiv” måste vara
grön d.v.s. banan är aktiv.
När skjutlaget är klart klickar man på ikonen ImportData i Excel
dokumentet.
SiusData vid
tävling
www.sius.se
SiusData vid tävling
INSTRUKTION
Dok. nr: XNA 250149
Datum: 2011-02-09
Sidan: 2 av 4
OBS! INNAN SIUS DATA STARTAS RENSA ALLA FILER I
MAPPEN DÄR SKJUTRESULTATEN SPARAS: C:\ resultat
1.
Starta Sius Data,
Välj det översta alternativet.
Skriv in eget fil namn eller använd föreslaget
datum,
OBS: Det får inte vara några mellanslag
I filnamnet.
Om SHOOTER används ha max
sex tecken i filnamnet
Tryck på OK
Om inte ”papperkorgen”
fösvinner starta o
det näst översta alternativet.
Klicka på ikonen ”VISA SKYTTARNA”
2.
Klicka på Import. Via nätverket sök mappen
skjutlagslistor på datorn där SHOOTER körs.
3.
Gör detta inför varje lag, om någon
omplacering av skyttar skulle ha skett.
Klicka på ikonen ”VISA BANOR”
4.
Välj ikonen ”ÖPPNA NYTT LAG”
5.
SiusData vid tävling
INSTRUKTION
Dok. nr: XNA 250149
Datum: 2011-02-09
Sidan: 3 av 4
Skriv in lagets nummer eller tryck på öka.
6. Välj rätt skjutprogram nere till vänster
7.
Klicka på gröna pilen
8. När alla skyttar är klara spara resultatet till SHOOTER
genom att trycka på ikonen
”DATA BACKUP”
9. Inför nästa skjutlag börja från punkt 2.
FINAL
OBS! Inför final skall Sius Data startas om och ny databas
skall skapas, se punkt 1.
SiusData vid tävling
INSTRUKTION
Dok. nr: XNA 250149
Datum: 2011-02-09
Sidan: 4 av 4
Flytta skytt inom skjutlaget
Skriv in skyttens startnummer som skall flyttas till ledig bana,
Radera namn på SiusView om banan går tom
För att ta bort
”gamla” resultat
från SiusView om
skytt saknas i
nästkommande
lag, aktivera då
banan som saknar
skytt
tryck på gröna pilen för den banan.
SiusData
skapa skott i
simuleringsmod
www.sius.se
SiusData skapa skott i simuleringsmod
INSTRUKTION
Dok. nr: XNA 250148
Starta SiusData I simuleringsmod
Öppna CU 931 Tangentbord
Datum: 2011-02-05
Sidan: 2 av 3
SiusData skapa skott i simuleringsmod
INSTRUKTION
Dok. nr: XNA 250148
Datum: 2011-02-05
Sidan: 3 av 3
Sen är det bara att skapa
skott med dessa knappar
Antal skott i serien
Skjutlaget skapas som en vanlig tävling, dock måste man använda
dom skjutprogrammen som finns som standard ex.
OBS! DET FUNGERAR INTE MED DE SKJUTPROGRAM SOM
FINNS UNDER ”EGEN TÄVLING”
SC-Program
www.sius.se
SC-Programs instructions:
SC-Programs are customer programs which can be sent to the control unit and will be saved in the SC
directory.
This Guide is a short description how to create such a SC-Program and send it to a control unit:
1. Open the Program Barcode Library.
2. Click on “Program\Settings…”
3. -Check if you are using the version 7.3e_Final for SA9003. If not, change it.
-Set the directory to the path where SiusData is installed and click “Ok”.
1
4. Create your own program. Click on the folder “User” and choose “Insert\Customer barcode\”
5. It appears a new window – the “Barcode editor”.
a. Insert the name of the program. This name will appear on the monitor
b. Choose a short name with maximum 4 letters. They will appear on the display of the
control unit.
c. Change to the right modus (Air pressure weapons, ISSF/SSSV 2550, …)
d. The legalisation is a free option which you can let 0.
e. The external number is also optional.
f. You may insert a description of your program.
g. Insert the desired competition
6. Click “Ok” to accept and close the window.
2
7. Click on User and Choose “Program\Create shortcut file”
8. Check if the current folder is “C:\programs\Sius Ascor\SiusData\”. Choose a name for your
competition and click “Save”
3
9. Go to “Program\Update SiusData”
10. Open SiusData. Check if you have installed at least version 2.03e.
11. Activate all those lines to which you want to send the shortcut program.
12. Choose “Settings\SCProgramme laden”
4
13. Open your created SCPrograms_File. Now the SC-File will be sent automatically to the
selected control units.
14. If the transfer is finished successful you will see this message:
15. Click “Ok” to close this window.
16. Now you can find the program in the control unit under “System\Control\SC-Programs” (F3,F3)
5
Elektroniskt markeringssystem
Underhåll tavla
LS10
HS10
SIUS MIATRON AB
Tfn:
021-600 13 (+4621 600 13)
Internet:
http://www.sius.se
E-post:
[email protected]
Dokument nr XNA 250145
SIUS / 2011-02-05
Innehållsförteckning
1.
2.
3.
4.
5.
6.
1.
Allmänt ....................................................................................................................... 2
Uppbyggnad och funktion ........................................................................................... 2
Underhåll .................................................................................................................... 2
Förbrukningsmaterial .................................................................................................. 3
Materialbeställning ...................................................................................................... 3
Noteringar ................................................................................................................... 3
Allmänt
Den elektroniska mättavlan LS10 och HS10 är konstruerad för alla 10 m luftvapendiscipliner,
samt gevär 50 m.
Vänligen beakta följande anvisning för underhållet av tavlan.
2.
Uppbyggnad och funktion
När kulan passerar genom tavlan detekteras kulan av tre oberoende infraröda lasermätsystem. Kulans position detekteras med en hög noggrannhet. Den höga noggrannheten
kan även utnyttjas för att visa kulans form! Därför är LASERSCORE® värdens noggrannaste
tavla.
Eftersom mätningen sker vid tavlans horisontella plan finns ingen risk för parallaxfel om
skjutningen sker snett mot tavlan. Detta är helt unikt och uppnås inte av någon annan tavla.
Som tillval finns bland annat belysning och skottverifiering med pappersremsa, nödvändigt
vid internationella ISSF mästerskap. Skottverifieringsmodulen monteras mot tavlans baksida.
Den väderskyddade elektroniken möjliggör att tavlan kan användas, inte bara för 10 m
luftgevär och pistol utan även för korthåll gevär utomhus.
3.
Underhåll
Underhållet av tavlan säkrar en felfri drift. Följande punkter skall beaktas:

att tavlans inre är rengjord och att de tre mottagarna inte är täckta av stoft
Tips!
Inför varje tävling skall tavlan rengöras.
Scheibenwartung S10-Lon_d, Version 1.0
-2-
SIUS AG / April 2012
4.
Förbrukningsmaterial
Pos.
1
2
3
4
5
5.
Artikel nr
Beskrivning
LS10A043R2
Försättstavla (PVC) Gevär
S20A022LS10/100
Försättstavla Gevär papper
LS10A040R2
Försättstavla (PVC) 50 m Gevär
LS10A044R2
Försättstavla (PVC) Pistol
S20A023/10
Försättstavla Pistol papper
Materialbeställning
Förbrukningsmaterial och reservdelar kan du beställa från:
SIUS MIATRON AB
Mälbyvägen 26
722 33 Västerås
Tfn:
021-600 13 (+4621 600 13)
Internet:
http://www.sius.se
E-post:
[email protected]
6.
Noteringar
Scheibenwartung S10-Lon_d, Version 1.0
-3-
SIUS AG / April 2012
Felrapport
www.sius.se
Felrapport
INSTRUKTION
Dok. nr: XNA 250156
Datum: 2011-02-05
Felrapport till SIUS skall innehålla:
1)
Felbeskrivning
Utskrift genom följande tangenttryckning på kontrollenheten:
2)
Hjälp tangenten
3)
Home\System\Underhåll\BIT-test\Taveltest
4)
Home\System\Rapport\Log\Allt
5)
Home\System\Underhåll\Rapport\Log\Log Hex
6)
Home\System\Underhåll\Rapport\Inställningar\Utskrift
Sidan: 2 av 2
F|UNODULQJFVYILO
www.sius.se
Start Nr Pri. Score
201
202
203
204
205
201
202
203
204
205
201
202
203
204
205
10
10
10
10
9
9
9
10
10
9
9
9
10
9
9
Match Ban
tiondel Divisions
shot
nr.
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
10.4
10.2
10.8
10.5
9.9
9.9
9.8
10.7
10.1
9.5
9.6
9.7
10.9
9.5
9.8
439
600
120
359
839
839
920
200
680
1159
1080
999
39
1159
920
Tid
46:43.7
46:49.8
46:55.9
47:02.2
47:08.3
47:23.8
47:29.8
47:35.9
47:42.2
47:48.3
48:03.8
48:09.8
48:15.9
48:22.2
48:28.3
Inner
In
Time
X-kord. Y-kord.
tia
time since ch
0
0
1
0
0
0
0
1
0
0
0
0
1
0
0
3.11
6
0.85
3.6
-5.94
-8.4
-6.51
1.41
4.81
8.2
-10.8
-7.07
0.28
0
6.51
-3.11
0
0.85
0
-5.94
0
6.51
1.41
-4.81
-8.2
0
-7.07
0.28
11.6
6.51
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
655.35
Sweep
dir.
Demo
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Prac- Ins Total
Fire Log
Log
Shoot tice
Del kind Group kind event type Time
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
3
3
3
3
3
6
6
6
6
6
7
7
7
7
7
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
110440375
110440984
110441593
110442218
110442828
110444375
110444984
110445593
110446218
110446828
110448375
110448984
110449593
110450218
110450828
Re- Wea- Pos- Target Ext.
lay pon ition ID
Nr.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
64
64
64
64
64
64
64
64
64
64
64
64
64
64
64
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Company-Documentation
Error Navigator SA931
Error Navigator
SA931
File: ErrorNavigatorSA931_en_V2.0.doc
Page 1 of 13
Company-Documentation
Error Navigator SA931
General
ATTENTION: Plug out the devices before opening them!
This Instruction for troubleshooting is made to localise system errors independently. The errors/questions
are listed in order to circumscribe more and more the error, if you go trough them step by step.
The troubleshooting is based on the World cup system SA931. Most of these functions apply for other SIUS
Ascor systems also.
To troubleshoot the error the manual is necessary!
If after circumscribing the error, an exchange of the faulty device (i.e. with second system) makes the system
work again, the confirmation of the found error is made. If you request SIUS for further assistance please
prepare this document and the made test results.
Remark: For better understanding you can find pictures of the CU931 and LME circuit-boards in section
“Software update” .
On malfunctions and false conclusions due to manipulations, on devices and their electronics, which
are NOT mentioned hereafter SIUS is not liable.
Troubleshooting
Error
No device shows any
reaction
Question
Is the fuse in order
Is the voltage-switch of the
power supply set right
Is the cabling correct
LED1 in device is not blinking
(CU931 / Target)
1
Remedy
Please exchange the fuse according to manual
→ ATTENTION: Check state of devices, eventually
send them back to SIUS to repair
Set voltage–switch to 110 respectively to 220 VAC
- Check cabling according to manual
- Check that the cables are snapped in correctly
Send device or electronic circuit board back to
SIUS to repair
Light-diode (Lamp) on case or on electronic circuit board
File: ErrorNavigatorSA931_en_V2.0.doc
Page 2 of 13
Kommentar [JE1]:
Company-Documentation
Error Navigator SA931
Error
Question
LED in CU931 / Target The LED on shooter monitor
are blinking, but else
(M931) does not lit
no reaction
LED on shooter monitor
(M931) is blinking
Picture on monitor (M931,
M1421) appears on power-up
and but ceases after
Is the brightness set right on
monitor
After the download of a new
“68000 Software” LED is light
(green)
System is hanging
Target can not be assigned to
CU931
Remedy
Connect monitor to the mains (220V) and turn it on
Check data cable connection, exchange monitor
(M931) or CU931
Turn up brightness
Set brightness
Check “Hardware Identifier Jumper” on CU931,
does it correspond to your software, or download
the “68000 Software” again
- Lock the RJ45 connector in the socket.
- Press the ServicePin at least 1 min.
- Was the LME allready configured (LED flash
slowly), it can’t configurred by a shot once again.
SIUSLANE has a red RS232- - Check the selected COM Port
Status indication, settings ok.? - Check the setting of the jumpers on target circuit
boards: “Lamp” for LON and “RS232” for
SIUSLANE.
If a jumper was set wrongly the circuit board should
be sent back to SIUS for control.
SIUSLANE has a red RS232- Only for cabling test:
Status indication, cabling ok.? Set one jumper across.
If the monitor shows “offline“
Is the LON-network set up
ideal
CU931 is hanging with the
message “Maxload“ on the
display
The system is booting, makes
a reset and boots again
File: ErrorNavigatorSA931_en_V2.0.doc
If the connection is ok the status turns to green.
Delete network configuration and reconfigure
according to manual
- Network-ends are set with terminations
- Brach lines are not longer than 2m
- For special systems (PC, Router etc.) consult the
manual
Download “68000 Software”. Is the error not fixed
send the device back to SIUS
- Are there only 2/10 systems per corresponding
power supply.
- The voltage of the power supply is too low
(min. 24VDC).
Page 3 of 13
Company-Documentation
Error Navigator SA931
Error
PC is hanging
Question
Get the LonDongle
disconnected while the PC
was running
No communication between
PC and LonDongle
Was there a new version of
SIUSData intalled
The system is booting
but operaton is not
possible
“Selftest” made without
connected printer D931?
Are settings made on the
CU931 which are not
reproducible
Was filter set unintentional
Was unintentional set remote
to on
Does the monitor show
“offline“ or does SIUSLANE
have a red RS232 status
display
Discipline choice makes the
following question pop up:
“All Data Required“, but can
not been activated
File: ErrorNavigatorSA931_en_V2.0.doc
Remedy
Send the LonDongle for check to SIUS.
Æ NEVER change a printerport device while the
PC is running (no HotSwap)
Read “troubleshooting_en.htm” at the directory
SIUSData\Help.
- Rename all *.ini files to *.ini.old and restart
SIUSData.
- The installation must be run twice. Once for
remove the old version, twice to install the new
one.
Connect and turn on printer D931 or make a
restart
Make a ColdStart (Reset) on the system.
→ ATTENTION: make ColdStart only according to
manual.
Saved filter will not cleared.
1. Switch off filter with “282806” (possible
anywhere)
2. Set back filter (factory setting)
3. Save filter
Make a ColdStart (Reset) on the system.
→ ATTENTION: make ColdStart only according to
manual.
Check connection between CU931 and target,
eventually wrong software in the target electronic.
Set FiDa OFF in “IdRq“ settings in “OPTIONS”
menu
Page 4 of 13
Company-Documentation
Error Navigator SA931
Error
The operation does
not function correctly.
Question
Are the SelfTest functions
executable.(Printer D931 is
necessary)
The barcode reader is not
working correctly
Malfunctions of keyboard
On special event’s (e.g. select
a new target) the system boot
Malfunctions of the display
File: ErrorNavigatorSA931_en_V2.0.doc
Remedy
Make all possible SelfTests:
− Printout with key Help
− Selected settings (Sett/Prnt)
− Shot memory (Log/All and LogH)
− Target Test (Trgt)
→ ATTENTION If you request SIUS for help please
prepare printouts; eventually fax them.
If barcode reader has no red light in front clean the
lens or exchange barcode reader: if still not
working, send back devise an reader to SIUS to
repair
Was unintentional set remote to on
Conduct Selftest (Self) (Printer D931 is necessary
On defect send back device to SIUS to repair
The memory is overflow with remaning data and
will be cleaned.
Æ If “Automatic Softstart” is ON (default), the
system make this under controll by it self.
Æ Do not change this setting!
Conduct Selftest (Self) (Printer D931 is necessary)
On defect send back device to SIUS to repair
Page 5 of 13
Company-Documentation
Error Navigator SA931
Error
Malfunctions of the
system
Question
The printer does not print
Remedy
- Conduct printer hardware selftest (plug in while
pressing LINE FEED and SELECT)
If no printout is made send the printer back to SIUS
to repair.
- Conduct printer software seftest (Self)
If there is no printout made contact SIUS.
– In the menu “OPTIONS“ move the cursor to the
complete right “>6“ (over the position “Lng“).
On the display in the upper right corner “ON“ or
“OFF“ appears, press ENTER. Now the “Printer
protocol“ menu comes up. Set to “ON“.
The printer feeds the paper but Is the printer paper inserted correctly?
no printout is made
The shiny side has to be visible.
Printer prints only very weak
Conduct printer hardware selftest (plug in while
pressing LINE FEED and SELECT).
“Head Rank“ letters have to correspond with the
letters on the printing unit, otherwise contact SIUS.
No paper feed on printer
Paper is jammed in “printer paper cover” or the
barrel needs to be cleaned with alcohol
Direction arrows are print as
Conduct selftest (Self). The arrows have to be in
special characters
the character set. If there are no arrows on the
printout contact SIUS
Printout of matrix printer is bad The ink ribbon is not inserted correctly or it needs
to be changed
LED on D931 is lit red
No paper or release handle is open, otherwise
(ALARM)
printing unit is defect
LED on D931 is not lit, but
If the printer has been opened the LED could be
functions well. (ALARM,
covered. Send back printer to SIUS to repair
PRINTER, SELECT)
On 25m range the light signals - Check cabling between TCU25 and VJ45LS
are not working
- Check if the Lamp/RS232 jumper on each
LME/target are on position Lamp
Red and green phase are
Inverse cabling in VJ45LS
inverted
On the second 25m bay only
Switch both channels of the TCU25 on INTERN
the TCU25 has a reaction but (internal), and the Master on OFF
not the light signals
The LONdongle is not working - Read the troubleshooting_en.html in the
correctly
SIUSDATA\Help-directory.
- Restart SIUSDATA (Settings in LONdongle are
reconfigured)
- In LonOrg search for LONdongle and devices.
If the LONdongle is not listed contact SIUS
File: ErrorNavigatorSA931_en_V2.0.doc
Page 6 of 13
Company-Documentation
Error Navigator SA931
Error
The displayed shot is
not correct
Question
Remedy
Comment: The discipline is not It is possible to shoot a 300m big bore rifle
depending ofn the target type discipline on a S10-LON target.
The TIC / MIX of the target informs this to the
CU931 (see manual)
Is the target maintained
- Clean microphones
correctly and the acoustic
- Mend the acoustic chamber
chamber in order
- Replace the backup-masks
- Exchange the heavy used front masks and
rubber membranes
→ see manual
Are the microphones clean
Remove dust and lead particles with brush
Do the microphones work
By knocking the microphones the corresponding
properly
LEDs on the target electronic are lit
On S10 and S25/50 a automatic paper/rubber feed
is made
Display Miss without
At target with framhit detector can display falsely a
shotsensor
Miss when it be hit by a grazing shot
After a shot “No paper feed“ is - Insert or replace paper/rubber band according to
displayed
manual.
- For S10-LON targets: Close target frame
- For S25/50 targets: Check transportation motor.
- Check “rubber band feed circuit board” for correct
fitting and cleanness
Is the band feed set correctly
Paper band feed S10:
Air rifle 2cm
in SIUSLANE
Air pistol 4cm
Rubber band feed S25/50: SB rifle 1mm
Pistol
2mm
→ ATTENTION: For proper function use band only
once
Is the setup of the target
Make Target Test (Targ) and check temperature
correct?
and TIC / MIX according manual. If the setup is not
(Printer D931 necessary)
correct send back target to SIUS to repair
Nr.
TIC
MIX
0
LME only Normal
1
S10
2
S25/50
3
S25
Rotated180
4
S100
5
S300
Flip0
6
DB100
7
DB128
Flip180
8
S101
Are the shots in “Demo-Mode” If no shots appear re-boot the system.
displayed
If error is not fixed send back target to SIUS to
repair
Is the shot sensor setting right Set shot sensor on/off correctly and check “Hidden
Miss“ (HMss)
OFF → Zero is shown
ON → Zero is only marked in log
File: ErrorNavigatorSA931_en_V2.0.doc
Page 7 of 13
Company-Documentation
Error Navigator SA931
Error
The displayed shot is
not correct
Question
Is the position of the shot
sensor / weapon right
Are the light sensors of the
shot sensor dirty
Are the light sensors exposed
to direct sun light
Shot indication without Did someone shoot on a
a fired shot
neighbour lane
10.9 without a shot on several
lanes
No shot indication
Are shots displayed in demo
mode
SIUSLANE has a red RS232Status indication
Is any device exposed to rain
(humidity)
Is the measurement bar of a
S110, S300 wet after rain
File: ErrorNavigatorSA931_en_V2.0.doc
Remedy
Are noise separation walls mounted?
→ see manual
Clean the plexiglas window of the light sensors
with a humid cloth
Protect shot sensor from direct sun light
- Turn on shot sensor
- On systems without shot sensor print out the log
(on lane and neighbour lanes). Check the missing
shot according to the time marks.
Print log and compare time marks of the 10.9’s of
the different lanes.
→ If the time is the same: The system is on the
same phase (230VAC) as an other consumer:
i.e. neon lamp (light on/off), electro-heating or
compressor.
If no shots appear re-boot the system. If error still
occurs, send the target back to SIUS to repair
Are the jumpers in the right direction on RS232,
(not across!)
Are all joints, covers and shutters present and
closed
Check rain protection according to manual
Page 8 of 13
Company-Documentation
Error Navigator SA931
Available Test Functions
Test-Function
SA931
SA921
Printer Test
MAINT./Test/Self
MAINT./Test/Self
Line Test
MAINT./Test/Line
MAINT./Test/Line
Memory Test Monitor
Automatic
Automatic
Target Test
MAINT./Test/Targ
MAINT./Test/Targ
Keyboard and Self Test
MAINT./Test/Self
MAINT./Test/Self
Individual Scoreboard Test
Azt
Demo On (Tip on “shot sensor”
OPT./Demo/ON
OPT./Demo/ON
or press “Ins“-key)
Demo Off
OPT./Demo/OFF
OPT./Demo/OFF
Print protocol
OPT./ 5x“>6“/ENTER
Monitor status
MAINT./Serv/Stat
MAINT./Serv/Stat
Print log
MAINT./Serv/PrnL
MAINT./Serv/PrnL
Shot Sensor On
OPT./Sens/ON
OPT./Sens/ON
Shot Sensor Off
OPT./Sens/OFF
OPT./Sens/OFF
Print “hidden miss” Off
OPT./HMss/OFF
OPT./HMss/OFF
Print “hidden miss” On
OPT./HMss/ON
OPT./HMss/ON
Show “hidden miss” Off
OPT./HMss/OFF
OPT./HMss/OFF
Show “hidden miss” On
OPT./HMss/ON
OPT./HMss/ON
Network Test
MAINT./Test/Net
Configure Network
MAINT./Net
Set time and date
MAINT./Time
Set language
OPT./Lng
OPT. ⇒ OPTIONS / MAINT. ⇒ MAINTENANCE
(Menu names, reach with “Next Window“)
File: ErrorNavigatorSA931_en_V2.0.doc
Page 9 of 13
Company-Documentation
Error Navigator SA931
Software UpDate
The control unit (CU931) has 4 Software components.
1. For the logic (electronic) the PLD (Programmable Logic Device) Software is responsible. This is in direct
relation to the circuit board print (Hardware) and can not be inserted into any circuit board version. The
software has to be loaded into the PROM (Programmable Read-only Memory) with a programmer. The
PROM can not be erased or reprogrammed. The version can be checked on the “Monitor Status“
printout or in LONorg.
2. For the communication between the control unit and the target the LON-software is responsible. This
communication-software has to be in accordance with the target LON-software! This Software is situated
in the LON-chip, a flash (electronically deleteable read-only memory) and can be downloaded with the
PC-software called LONorg. The version can be checked on the “Monitor Status“ printout or in LONorg.
3. The Boot Strap Loader (BSL) loads or refreshes the monitor software and makes a plausibility check at
the boot up. The software is saved in the lowest area of the operating program flash and can be
downloaded with a parallel download cable (See appendix) . If the BSL is exchanged the operating
program is deleted! This implicates that the operating program has to be re-downloaded. The version
can be checked on the CU931 display during booting, on the “Monitor Status“ printout or in LONorg.
The monitor software (68‘000) is in effect the operating program. This software is situated in the upper area
of the operating program flash and can be downloaded with the PC-software called LONorg. The version
can be checked on the shooters monitor at the end of booting, on the “Monitor Status” printout
CU931
PLD
Processor
BSL
68‘000
Software
PLD
LOGIC
LON
Processor
& Flash
Fuse
LED LON (rot) / 68'000 (green)
LON-Network
HIC
Flash for
BSL and 68‘000
Processor
PLD Logik
RAM
PLD Software
Battery for RAM-Data
LCD contrast
LON Processor and Flash
File: ErrorNavigatorSA931_en_V2.0.doc
Download-connector BSL
Page 10 of 13
Company-Documentation
Error Navigator SA931
The target electronic (LME) has 2 software components.
1. For the logic (electronic) the PLD (Programmable Logic Device) Software is responsible. This is in direct
relation to the circuit board print (Hardware) and can not be inserted into any circuit board version. The
software has to be loaded into the PROM (Programmable Read-only Memory) with a programmer. The
PROM can not be erased or reprogrammed. The version can be checked on the “Target Test” printout
as PIC (PLD Identification Code) or in LONorg.
2. For the communication between target and control unit the LON-Software is responsible. It also receives
the shot data and sends it to the control unit. This communication-software has to be in accordance with
the control unit LON-software! This Software is situated in a flash (electronically deleteable read-only
memory) and can be downloaded with the PC-software called LONorg. The version can be checked on
the “Monitor Status“ printout or in LONorg.
LME
PLD
PLD
LOGIC
LON
Shot data
processing
LON
Software
Mic
processing
Mic-processing
Amplification
Software
LON-Network
Processor
Target variant
RAM
LON/RS232
HIC
MIC 1...4
(rot) and
Software
(green) LED
PLD Software
PLD - LON LON-Processor
Logic Software
LON LED and Service Pin
Download Software
Software maintenance can be made with the PC-program called LONorg and a LONdongle. The software
versions can be checked and newer software can be downloaded.
LONorg is automatically installed if you install SIUSDATA
or you can get it as ZIP-file called:“LonOrg_1_16.zip“.
De-zip it into the root directory of C: and all program and directories are made to run the software.
Update BSL
The BSL is the same version in all control units and does not need to be updated normally. If in some
cases the BSL has to be updated, it can be done with the “Downloader“
in LONorg, over the parallel
download cable (see annex). To be able to use the “Downloader“ in LONorg the activation code
be inserted.
has to
ATTENTION: If the BSL is updated the operating software is deleted and has to be re-downloaded!
File: ErrorNavigatorSA931_en_V2.0.doc
Page 11 of 13
Company-Documentation
Error Navigator SA931
ATTENTION: Due to a wrong handling the repair of all devices might become necessary!
1. Connect the SA931 system with LONdongle to a PC
2. Copy the CU931 update-file into the directory:
C:\Program Files\Sius Ascor\SiusData\LonOrg\Download\ME 68000.
3. Copy the LME (target) update-file into the directory:
C:\Program Files\Sius Ascor\SiusData\LonOrg\Download\LME
4. Start the LONorg software
in the directory C:\Program Files\Sius Ascor\SiusData\LonOrg\
5. The LONorg main screen appears with the registers: “CU931“, “LME“, “Known“, “Unknown“ and “Router“.
6. If the main screen does not appear click on
to activate it.
7. Search for all devices in the LON-network with.
8. The screen should display the following for CU931 or LME (targets):
Register CU931
Register LME (targets)
If the system was configured according to the manual, the x in “(SN x)“ is the lane number
9. Now all CU931 or LME (targets) can be marked; With the button “Refresh”, the versions of the connected
devices is shows. With “File“ button the new software of point 2. or 3. Can be selected. With “Start” button the
corresponding software is downloaded to the selected devices.
ATTENTION: The LON-software is downloaded to the selected devices only, the 68'000-software (monitor/operating software) is downloaded to ALL connected CU931!
10. Press “Refresh” button to check the downloaded version of all devices.
Select devices and download again.
º LON-version not updated (very rarely):
Disconnect all devices which had a successful download
º 68‘000-version not updated:
from the LON-network and download again.
11. With this button
program start.
the language of LONorg can be changed. The selected language is activated at the next
12. Clicking on
, for detailed information (help file).
For further inquiries contact:
SIUS AG, Im Langhag 1, CH-8307 Effretikon
Tel.: +41 52 354 60 60, Fax: +41 52 354 60 66, www.sius.com
File: ErrorNavigatorSA931_en_V2.0.doc
Page 12 of 13
Company-Documentation
Error Navigator SA931
Annex
S te c k e r 2
S te c k e r 1
1A
25
1B
13
1
14
M a le
S ig n a l
P lu g 1
C a b le 1
P lu g 2
as3 8 1
P - D0
P – D1
P – D2
P – D3
P – D4
P – D5
P – D6
P – D7
X P - S tr o b e
S ta r t
P - B usy
GND
as0 8 3
P in
C o lo u r
P in
1B
1A
2B
2A
3B
3A
4B
4A
5B
5A
6B
5A
B rau n
2
3
4
5
6
7
8
9
1
16
11
25
R ed
O rang e
Y e llo w
G reen
B lu e
P u r p le
G rey
W h it e
B la c k
B rau n
R ot
BSL Parallel download cable
File: ErrorNavigatorSA931_en_V2.0.doc
Page 13 of 13
PROGRAMVARA
Datum: 2012-11-19
Bifogade CD innehåller programvaran för Er PC vid skjutledaren.
Vänligen installera direkt under C:\Sius Ascor\............
1 (1)