Advertisement
Advertisement
BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR Kupplungstechnik GmbH D-48407 Rheine KTR-N Sheet: Edition: 40114 EN 1 of 20 5 BoWex-ELASTIC® highly flexible flange couplings types HEW1, HEW2 and their combinations according to standard 94/9/EC (ATEX 95) for finish bored, pilot bored and unbored couplings Type HEW1 Type HEW2 BoWex-ELASTIC® highly flexible flange couplings types HEW-ZS and their combinations for finish bored, pilot bored and unbored couplings Type HEW-ZS Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 2 of 20 5 The BoWex-ELASTIC® HEW is a high flexible plug-in shaft coupling. It dampens torsional oscillations, decreases shocks and is impact sound insulating. The BoWex-ELASTIC® HEW coupling compensates for relatively considerable shaft displacements caused by e. g. inaccuracies in production, heat expansion etc. Table of Contents 1 Technical Data 2 Hints 2.1 2.2 2.3 2.4 2.5 Coupling Selection General Hints Safety and Advice Hints General Hints to Danger Proper Use 3 Storage 4 Assembly 4.1 4.2 4.3 4.4 4.5 5 Components of the Couplings Hint Regarding the Finish Bore Assembly of the Coupling Displacements - Alignment of the Couplings Spares Inventory, Customer Service Addresses Enclosure A Hints and instructions regarding the use in 5.1 Use in hazardous areas Hazardous Areas According to the Regulations 5.2 Control intervals for couplings in 5.3 Checking of torsional backlash 5.4 Approximate values of wear hazardous areas Marking of coupling for the hazardous area 5.5 5.6 Starting 5.7 Breakdowns, causes and elimination 5.8 Certificate of Conformity according to the EG Standards 94/9/EG dated 23 March 1994 Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR Kupplungstechnik GmbH D-48407 Rheine KTR-N Sheet: Edition: 40114 EN 3 of 20 5 1 Technical Data ® ® Illustration 1: BoWex-ELASTIC type HEW1 Illustration 2: BoWex-ELASTIC type HEW2 Table 1: dimensions – type HEW1 and HEW2 Size 42 48 65 80 G 80 100 125 G 125 150 Max. finish bore [mm] d3 d2 48 50 48 55 65 75 80 80 85 95 100 110 125 125 125 125 150 150 D 68 68 96 124 124 152 192 192 225 Size 42 48 65 80 G 80 100 125 G 125 150 l3 15 17 28 17 22 16 18 15 18 l4 50 55 75 80 90 111,5 170 170 150 l5 42 45 63 70 78 110 171 157 143 D2 162 180 224 295,27 333,4 438,15 438,15 489 542,9 Dimensions [mm] E 4 4 5 5 5 20 zxM 6 8 8 8 8 8 16 8 6 M6 M6 M8 M10 M10 M12 M12 M12 M16 E1 32 32 42 45 55 57 47 47 64 Dimensions [mm] D4 146 164 205 266 302 350 416 440 470 LHEW1 132 137 187 215 235 278,5 357 357 364 D5 180 200 245 318 358 478 478 530 585 LHEW2 104 109 150 160 185 320 D6 85 92 125 130 145 158 175 175 225 Weight with max. bore [kg] 4,3 5,5 13,2 19,7 25,9 50,5 75,8 96,1 114,3 l1 50 50 70 90 90 110 140 140 150 l2 45 45 55 70 80 80 99 95 140 Mass moment of 2 inertia [kgm ] JL JA 0,0121 0,0015 0,0204 0,0019 0,0752 0,0071 0,1449 0,0285 0,2748 0,0422 0,8396 0,1068 0,9631 0,2777 1,4491 0,3031 2,8644 0,4314 Table 2: torques Size 42 48 65 80 G 80 Elastomer hardness [Shore A] 40 50 65 40 50 65 40 50 65 40 50 65 40 50 65 Please note protection mark ISO 16016. Drawn: Verified: Torque [Nm] TK max. TKN 130 390 150 450 180 540 200 600 230 690 280 840 350 1050 400 1200 500 1500 750 2250 950 2850 1200 3600 1250 3750 1600 4800 2000 6000 08.11.11 Pz/Hk 09.11.11 Pz Size 100 125 G 125 150 Elastomer hardness [Shore A] 40 50 65 40 50 70 40 50 70 40 50 70 Replaced for: Replaced by: Torque [Nm] TK max. TKN 2000 6000 2500 7500 3200 9600 3000 9000 4000 12000 5000 15000 4000 12000 5200 16000 6500 20000 5500 16500 7000 21000 9000 27000 KTR-N valid from 08.04.04 BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR Kupplungstechnik GmbH D-48407 Rheine KTR-N Sheet: Edition: 40114 EN 4 of 20 5 1 Technical Data ® Illustration 3: BoWex-ELASTIC type HEW-ZS (size 48 to G 80) ® Illustration 4: BoWex-ELASTIC type HEW-ZS (size 100 to G 125) Table 3: dimensions – type HEW-ZS1) Size 48 65 80 G 80 100 125 G 125 Max. finish bore [mm] d4 d3 55 28 75 45 80 65 95 65 110 90 125 120 125 120 1) zxM 8 8 8 8 8 16 8 D4 164 205 266 302 350 416 440 M6 M8 M10 M10 M12 M12 M12 Dimensions [mm] Size 48 65 80 G 80 100 125 G 125 D2 180 224 295,27 333,4 438,15 438,15 489 D5 200 245 318 358 478 478 530 Dimensions [mm] D6 92 125 130 145 158 175 175 D7 78 110 145 145 180 225 225 Removeable part HEW-ZS LZ [mm] l4 l5 l6 100 120 55 75 80 90 111,5 170 170 45 63 70 78 110 171 157 45 56 75 75 76 76 76 140 180 250 D8 45 72 100 100 135 180 180 l1 50 55 90 90 80 80 80 Weight with max. bore [kg] 6,9 16,0 25,5 34,2 l2 45 55 70 80 80 99 95 l3 17 28 17 22 16 18 15 Mass moment of inertia [kgm2] JA JL 0,0203 0,0747 0,1447 0,2752 0,0050 0,0160 0,0699 0,1412 ® For torques of BoWex-ELASTIC type HEW-ZS see table 2. BoWex-ELASTIC® couplings with attached parts that can generate heat, sparks and static charging (e. g. combinations with brake drums, brake disks, overload systems like torque limiters, impellers etc.) are not allowed for the use in hazardous areas. A separate checking must be made. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 5 of 20 5 2 Hints 2.1 Coupling Selection ! CAUTION! For a continuous and troublefree operation of the coupling it must be designed according to the selection instructions (according to DIN 740 part 2) for the particular application (see BoWex-ELASTIC® catalogue). If the operating conditions (performance, speed, changes on engine and machine) change, the coupling selection must be checked again. Please make sure that the technical data regarding torque only refer to the elastomer part. The transmissible torque of the shaft/hub connection must be checked by the orderer, and he is responsible for the same. For drives with dangerous torsional vibration (drives with periodical load on torsional vibration) it is necessary to make a torsional vibration calculation to ensure a perfect selection. Typical drives with dangerous torsional vibration are e. g. drives with diesel engines, piston pumps, piston compressors etc. On request KTR will perform the coupling selection and the torsional vibration calculation. 2.2 General Hints Please read through these mounting instructions carefully before you set the coupling into operation. Please pay special attention to the safety instructions! The BoWex-ELASTIC® coupling is suitable and approved for the use in hazardous areas. When using the coupling in hazardous areas please observe the special hints and instructions regarding safety mentioned in enclosure A. The mounting instructions are part of your product. Please keep them carefully and close to the coupling. The copyright for these mounting instructions remains with KTR Kupplungstechnik GmbH. 2.3 Safety and Advice Hints STOP DANGER! Danger of injury to persons. ! CAUTION! Damages on the machine possible. ATTENTION! Pointing to important items. PRECAUTION! Hints concerning explosion protection. 2.4 General Hints of Danger STOP DANGER! With assembly, operation and maintenance of the coupling it has to be made sure that the entire drive train is protected against unintentional engagement. You can be seriously hurt by rotating parts. Please make absolutely sure to read through and observe the following safety instructions. All operations on and with the coupling have to be performed taking into account "safety first". Please make sure to disengage the power pack before you perform your work. Protect the power pack against unintentional engagement, e. g. by providing hints at the place of engagement or removing the fuse for current supply. Do not touch the operation area of the coupling as long as it is in operation. Please protect the coupling against unintentional touch. Please provide for the necessary protection devices and caps. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 6 of 20 5 2 Hints 2.5 Proper Use You may only assemble, operate and maintain the coupling if you carefully read through the mounting instructions and understood them had technical training are authorized to do so by your company The coupling may only be used in accordance with the technical data (see table 1 to 3 in chapter 1). Unauthorized modifications on the coupling design are not admissible. We do not take any warranty for resulting damages. To further develop the product we reserve the right for technical modifications. The BoWex-ELASTIC® type HEW and HEW-ZS described in here corresponds to the technical status at the time of printing of these mounting instructions. 3 Storage The coupling hubs are supplied in preserved condition and can be stored at a dry and roofed place for 6 - 9 months. The features of the elastomer parts remain unchanged for up to 5 years in case of favourable storage conditions. ! CAUTION! The storage rooms may not include any ozone-generating devices, like e. g. fluorescent light sources, mercury-vapour lamps or electrical high-voltage appliances. Humid storage rooms are not suitable. Please make sure that there is no condensation. The best relative air humidity is below 65%. 4 Assembly Basically the coupling is supplied in individual parts. Before assembly the coupling has to be inspected for completeness. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR Kupplungstechnik GmbH D-48407 Rheine KTR-N Sheet: Edition: 40114 EN 7 of 20 5 4 Assembly 4.1 Components of the Couplings Components of BoWex-ELASTIC®, type HEW1 and HEW2 Component 1 2 4 5 7 1) Quantity 1 1 1 see table 1 1) 2 Designation elastomer part hub coupling flange cylinder head screw DIN EN ISO 4762 1) setscrew DIN EN ISO 4029 For size 150 nuts according to DIN EN ISO 4014 are required additionally. ® ® Illustration 5: BoWex-ELASTIC type HEW1 Illustration 6: BoWex-ELASTIC type HEW2 Components of BoWex-ELASTIC®, type HEW-ZS Component 1 2 3 4 4.1 4.2 4.3 5 6 7 Quantity 1 1 1 1 1 1 see table 4 see table 1 see table 4 2 Designation elastomer part hub spec. ZW-hub coupling flange adaptor flange flange hub cylinder head screw DIN EN ISO 4762 cylinder head screw DIN EN ISO 4762 cylinder head screw DIN EN ISO 4762 setscrew DIN EN ISO 4029 ® Illustration 7: BoWex-ELASTIC type HEW-ZS (size 48 to G 80) ® Illustration 8: BoWex-ELASTIC type HEW-ZS (size 100 to G 125) Table 4: cylinder head screws DIN EN ISO 4762 Size Quantity z (component 4.3) Quantity z (component 6) Please note protection mark ISO 16016. Drawn: Verified: 48 8 65 12 08.11.11 Pz/Hk 09.11.11 Pz 80 12 G 80 12 Replaced for: Replaced by: 100 15 12 125 12 12 G 125 12 12 KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 8 of 20 5 4 Assembly 4.2 Hint Regarding the Finish Bore DANGER! The maximum permissible bore diameters d (see table 1 to 3 in chapter 1 - Technical Data) must not be exceeded. If these figures are disregarded, the coupling may tear. Rotating particles may cause serious danger. STOP Hub bores or coupling flange bores machined by the customer have to observe concentric running or axial running, respectively (see illustration 9). Please make absolutely sure to observe the figures for dmax. Carefully align the hubs or coupling flange when the finish bores are brought in. Please use a setscrew according to DIN EN ISO 4029 or an end plate to fasten the hubs or coupling flange axially. Illustration 9: concentric running and axial running CAUTION! The orderer is responsible for all subsequently made machinings to unbored or pilot bored and to finish machined coupling parts and spare parts. KTR does not assume any warranty claims resulting from insufficient remachining. ! PRECAUTION! KTR supplies unbored or pilot bored coupling parts and spare parts on explicit customer´s request. These parts are additionally labelled with the symbol . Table 5: setscrews DIN EN ISO 4029 Size Screw size Tightening torque TA [Nm] 42 M8 48 M8 65 M10 80 M10 G 80 M10 100 M12 125 M16 G 125 M16 150 M20 10 10 17 17 17 40 80 80 140 Table 6: Recommended combinations of fit acc. to DIN 748/1 Bore [mm] above to 50 50 Shaft tolerance Bore tolerance k6 m6 H7 (KTR-Standard) If a feather key is intended to be used in the hub, it should correspond to the tolerance ISO JS9 (KTR-Standard) with normal operating conditions or ISO P9 with heavy operating conditions (frequently alternating torsional direction, shock loads, etc.). The transmissible torque of the shaft/hub connection must be checked by the orderer, and he is responsible for the same. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 9 of 20 5 4 Assembly 4.3 Assembly of the Coupling ATTENTION! We recommend to check bores, shaft, keyway and feather key for dimensional accuracy before assembly. Heating the hub, flange hub or coupling flange slightly (approx. 80 °C) allows for an easier installation onto the shaft. PRECAUTION! Please pay attention to the danger of ignition in hazardous areas. STOP ! DANGER! Touching the heated hubs causes burns. We would recommend to wear safety gloves. CAUTION! For the assembly please make sure that the distance dimension E or LZ (see table 1 and 3) is kept to ensure that the elastomer part can be moved axially. Disregarding this hint may cause damage on the coupling. Applying for type HEW-ZS only (size 100 to G 125)! Screw the flange hub (component 4.2) to the additional flange (component 4.1) at the tightening torques TA mentioned in table 7. Table 7: cylinder head screws DIN EN ISO 4762 Size Tightening torque TA [Nm] 100 355 125 355 G 125 355 Assemble the hub, flange hub or adaptor flange onto the shaft of driving and driven side. Shift the power packs in axial direction until the installation dimension LHEW1, LHEW2 or LHEW-ZS has been achieved. If the power packs have already been firmly mounted, the mounting dimension has to be adjusted by shifting the hub, flange hub or coupling flange axially on the shafts. Fasten the hub, flange hub or coupling flange by tightening the setscrews DIN EN ISO 4029 with cup point (tightening torque see table 5). Applying for type HEW-ZS only! Put the hub spec. (component 2) in front of the hub ZW (component 3) and screw the components at the tightening torques TA mentioned in table 8. Table 8: cylinder head screws DIN EN ISO 4762 Size Tightening torque TA [Nm] Please note protection mark ISO 16016. 48 65 80 G 80 100 125 G 125 41 69 120 120 190 295 295 Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 10 of 20 5 4 Assembly 4.3 Assembly of the Coupling Put the elastomer part (component 1) in front of the flange hub with additional flange or coupling flange. Screw the parts hand-tight for the time being. Afterwards tighten the screws at the tightening torque TA mentioned in table 9. ! CAUTION! For the assembly please make sure that the hub toothing is covered completely by the internal toothing of the elastomer part. (Please observe the assembly dimensions LHEW1, LHEW2 or LHEW-ZS.) Disregarding this hint may cause damage on the coupling. Table 9: cylinder head screws DIN EN ISO 4762 Size Tightening torque TA [Nm] 42 48 65 80 G 80 100 125 G 125 150 14 14 35 69 69 120 120 120 295 PRECAUTION! If used in hazardous areas the grub screws to fix the hub as well as all screw connections must be additionally secured against self-loosening, e. g. glue with Loctite (medium strength). ! CAUTION! Please observe the manufacturer´s instructions when using the glue. Do not put any glue onto the rubber surfaces. 4.4 Displacements - Alignment of the Couplings The BoWex-ELASTIC® HEW couplings accept a deviation of position of the machine parts to be connected up to the data indicated in table 10. In case of the alignment, the radial and angular displacement should be as small as possible, because the lifetime is increased hereby under the same operating conditions. The alignment of the BoWex-ELASTIC® HEW coupling has to be effected from the shaft-sided coupling hub to one of the processed surfaces of the flange hub. ! CAUTION! In order to ensure a long service life of the coupling and to avoid dangers regarding the use in hazardous areas, the shaft ends must be accurately aligned. Please absolutely observe the displacement figures indicated (see table 10). If the figures are exceeded, the coupling is damaged. The more accurate the alignment of the coupling, the higher is its lifetime. In case of a use in hazardous areas for the explosion group IIC (marking II 2GD c IIC T X), only half of the displacement figures (see table 10) are permissible. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 11 of 20 5 4 Assembly 4.4 Displacements - Alignment of the Couplings Please note: The displacement figures mentioned in table 10 are maximum figures which must not arise in parallel. If radial and angular displacement arises in parallel, the permissible displacement figures may only be used proportionately (see illustration 11). The displacement figures mentioned are general figures that apply up to an ambient temperature of 80 °C, ensuring a sufficient service life of the BoWex-ELASTIC® coupling. Displacement figures between the speeds indicated have to be interpolated accordingly. If necessary, please ask about the displacement for the corresponding coupling type. Please check with a dial gauge, ruler or feeler whether the permissible displacement figures of table 10 can be observed. Radial displacement Angular displacement Axial displacement Illustration 10: displacements Illustration 11: combinations of displacement Example for the misalignment combinations given in illustration 11: Example 1: Kr = 30 % Kw = 70 % Example 2: Kr = 60 % Kw = 40 % Ktotal = Kr + Kw 100 % Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR Kupplungstechnik GmbH D-48407 Rheine KTR-N Sheet: Edition: 40114 EN 12 of 20 5 4 Assembly 4.4 Displacements - Alignment of the Couplings Table 10: displacement figures Displacement figures Elastomer hardness [Shore A] 40 50 65 40 50 65 40 50 65 40 50 65 40 50 65 48 1,2 1,1 0,5 1,1 1,0 0,4 3,8 3,5 1,7 1,0 0,75 0,5 0,5 0,4 0,25 65 1,6 1,5 0,7 1,4 1,3 0,5 5,1 4,7 2,2 1,0 0,75 0,5 0,5 0,4 0,25 80 1,8 1,7 0,8 1,6 1,5 0,6 5,7 5,3 2,4 1,0 0,75 0,5 0,5 0,4 0,25 G 80 2,0 1,9 0,9 1,8 1,7 0,8 6,0 5,7 2,7 1,0 0,75 0,5 0,5 0,4 0,25 100 2,2 2,0 1,0 1,9 1,7 0,9 6,5 6,0 3,0 1,0 0,75 0,5 0,5 0,4 0,25 40 / 50 / 65 1,5 1,5 1,5 1,5 1,5 1,5 40 / 50 / 65 ±2 ±2 ±2 ±2 ±2 ±3 perm. radial displacement with n=1500 1/min. Kr (mm) perm. radial displacement with n=3000 1/min. Kr (mm) max. radial displacement 1) Kr max. (mm) perm. angular displacement with n=1500 1/min. Kw (°) perm. angular displacement with n=3000 1/min. Kw (°) max. angular displacement 1) Kw max. (°) perm. axial displacement Ka (mm) Displacement figures 40 50 70 40 50 70 40 50 70 40 50 70 40 50 70 125 3,3 2,5 1,1 2,9 2,1 1,0 7,5 6,9 3,3 1,0 0,75 0,5 0,5 0,4 0,25 Size G125 3,3 2,5 1,1 2,9 2,1 1,0 7,5 6,9 3,3 1,0 0,75 0,5 0,5 0,4 0,25 150 3,5 2,5 1,3 3,0 2,2 1,1 8,0 7,5 4,0 1,0 0,75 0,5 0,5 0,4 0,25 40 / 50 / 70 1,5 1,5 1,5 40 / 50 / 70 ±3 ±3 ±5 Elastomer hardness [Shore A] perm. radial displacement with n=1500 1/min. Kr (mm) perm. radial displacement with n=3000 1/min. Kr (mm) max. radial displacement 1) Kr max. (mm) perm. angular displacement with n=1500 1/min. Kw (°) perm. angular displacement with n=3000 1/min. Kw (°) max. angular displacement 1) Kw max. (°) perm. axial displacement Ka (mm) 1) Size 42 1,1 1,0 0,5 0,8 0,7 0,4 3,6 3,3 1,5 1,0 0,75 0,5 0,5 0,4 0,25 for short-term start 4.5 Spares Inventory, Customer Service Addresses A basic requirement to guarantee the operational readiness of the coupling is a stock of the most important spare parts on site. Contact addresses of the KTR partners for spare parts and orders can be obtained from the KTR homepage at www.ktr.com. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 13 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Type HEW1and HEW2: Hazardous Areas Hub / Elastomer part / Coupling flange Attachment A only applies for BoWex-ELASTIC HEW1 and HEW2. 5.1 Use in Hazardous Areas According to the Regulations Conditions of operation in hazardous locations BoWex-ELASTIC® couplings are suitable for the use according to EC standard 94/9/EC. 1. Industry (with the exception of mining) device class II of category 2 and 3 (coupling is not approved for device class 1) media class G (gases, fogs, steams), zone 1 and 2 (coupling is not approved for zone 0) media class D (dusts), zone 21 and 22 (coupling is not approved for zone 20) explosion class IIC (explosion class IIA and IIB are included in IIC) Temperature class: Temperature class T4, T3, T2, T1 T5 T6 Ambient or operating temperature - 30 °C to + 80 °C - 30 °C to + 65 °C - 30 °C to + 50 °C Max. surface temperature 1) 115 °C 2) 100 °C 85 °C Explanation: The maximum surface temperatures each result from the permissible ambient or operating temperature Ta plus the maximum temperature increase T of 35 K which has to be taken into account. 1) The ambient or operating temperature Ta is limited to + 80° C by the permissible permanent operating temperature of the BoWex-ELASTIC® elastomer parts used. 2) The maximum surface temperature of 115 °C applies for the use in locations which are potentially subject to dust explosion, too. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 14 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in 5.2 Control Intervals for Couplings in Hazardous Areas Explosion group 3G 3D II 2GD c IIB T4, T5, T6 Hazardous Areas Control intervals For couplings which are classified in category 3G or 3D the operating and assembly instructions that are usual for standard operation apply. During the standard operation which has to be subject to the analysis of danger of ignition the couplings are free from any ignition source. Merely the temperature increase produced by proper heating and depending on the coupling type has to be considered: for BoWex-ELASTIC®: T = 35 K A review of the circumferential backlash and a visual inspection of the flexible elastomer part must be effected after 1,000 operating hours for the first time, after 6 months at the latest. Except for centered, stiff connecting flanges (e. g. bellhousings). If you note unconsiderable or no wear on the elastomer part after this first inspection, the future inspections can be effected, in case of the same operating parameters, respectively after 2,000 operating hours or after 18 months at the latest. If you note considerable wear during the first inspection, so that a change of the elastomer part would be recommended, please find out the cause according to the table „Breakdowns“, as far as possible. The maintenance intervals must be adjusted according to the changed operating parameters. BoWex-ELASTIC® Here the backlash between the hub and the nylon toothing must be checked by a torsional backlash, separately from the drive and the driven end. The friction / wear may only be Xmax. of the original toothing strength before the elastomer part must be replaced. When reaching the torsional backlash Smax. the elastomer part must be replaced immediately, irrespective of the inspection intervals. Visual inspection of the elastomer part (fractures, holes or similar). ® Illustration 12: BoWex-ELASTIC (type HEW1) Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 15 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.3 Checking of Torsional Backlash CAUTION! To check the torsional backlash the driving power pack turned off must be secured against unintended switching on. ! Drive end Turn the hub in opposite direction to the direction of drive. ! CAUTION! Here the elastomer part may not be axially displaced from its wear position. Mark elastomer part and hub (see illustration 13). Turn the hub in the direction of drive and measure the torsional backlash Smax. When reaching the torsional backlash Smax the elastomer part must be replaced. Driven end Turn the hub in the direction of drive. ! CAUTION! Here the elastomer part may not be axially displaced from its wear position. Mark elastomer part and hub (see illustration 13). Turn the hub in opposite direction to the direction of drive and measure the torsional backlash Smax. When reaching the torsional backlash Smax the elastomer part must be replaced. Illustration 13: marking of the elastomer part and the hub Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 16 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.4 Approximate Values of Wear If the torsional backlash is Smax. [mm] / friction Xmax. [mm], the elastomer part must be replaced. Reaching the exchange values depends on the operating conditions and the existing operating parameters. CAUTION! In order to ensure a long lifetime of the coupling and to avoid dangers regarding the use in hazardous areas, the shaft ends must be accurately aligned. Please absolutely observe the displacement figures indicated (see table 10). If the figures are exceeded, the coupling is damaged. ! Illustration 14: elastomer part in new condition Illustration 15: wear of elastomer part Table 11: Limits of wear each hub Torsional backlash Friction Xmax. [mm] Smax. [mm] 1,0 1,7 1,0 1,8 1,4 2,5 1,6 2,7 1,6 2,7 Size 42 48 65 80 G 80 5.5 Limits of wear each hub Torsional backlash Friction Xmax. [mm] Smax. [mm] 1,8 3,1 2,0 3,5 2,0 3,5 2,0 3,5 Size 100 125 G 125 150 Marking of Coupling for the Hazardous Area The ATEX marking of the BoWex-ELASTIC® coupling is performed on the polyamide flange of the elastomer indicating the following details: Short labelling: (standard) II 2GD c IIB T X Complete labelling: II 2G c IIB T6, T5 bzw. T4 - 30 °C Ta + 50°C, + 65 °C bzw. + 80 °C II 2D c T 115 °C - 30 °C Ta + 80 °C The labelling with Explosion Group llB included the Explosion Group llA. ! CAUTION! The orderer is responsible for all subsequently made machinings to unbored or pilot bored and to finish machined coupling parts and spare parts. KTR does not assume any warranty claims resulting from insufficient remachining. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 17 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.6 Starting Before putting the coupling into operation, check the tightness of the setscrews in the hubs, the alignment and the distance dimensions LHEW1, LHEW2 bzw. LHEW-ZS and correct, if necessary, and also check all screw connections regarding the stipulated tightening torques dependent on the type of coupling. If used in hazardous areas the grub screws to fix the hub as well as all screw connections must be additionally secured against self-loosening, e. g. glue with Loctite (medium strength). Last but not least, the coupling protection against unintended contact must be fixed. The cover must be electrically conductive and be included in the equipotential bonding. Bellhousings (magnesium part below 7,5 %) made from aluminium and damping rings (NBR) can be used as connecting element between pump and electric motor. The cover may only be taken off after having stopped the unit. During operation, please pay attention to strange running noises occurring vibrations. If the couplings are used in dust explosive areas and in mining the operator must make sure that there is no accumulation of dust in a critical quantity between the cover and the coupling. The coupling must not operate in an accumulation of dust. For covers with unlocked openings on the upper side no light metals may be used if the couplings are used as appliances of appliance group ll (if possible, from stainless steel). If the couplings are used in mining (appliance group l M2), the cover must not be made from light metal. In addition, it must be resistant to higher mechanical loads than if it is used as appliance of appliance group ll. The minimum distance „Sr“ between the protection device and the rotating parts must at least correspond to the figures mentioned below. If the protection device is used as cover, regular openings complying with the explosion protection demands can be made that must not exceed the following dimensions: Openings Circular - max. diameter Rectangular - max. lateral length Straight or curved slot max. lateral length/height ! Top side 4 4 Cover [mm] Lateral parts 8 8 Distance „Sr“ 10 10 prohibited 8 20 CAUTION! If you note any irregularities with the coupling during operation, the drive unit must be turned off immediately. The cause of the breakdown must be found out with the table „Breakdowns“ and, if possible, be eliminated according to the proposals. The potential breakdowns mentioned can be hints only. To find out the cause all operating factors and machine components must be considered. Coupling layer: If coated (priming, painting etc.) couplings are used in hazardous areas, the requirements to conductability and layer thickness must be considered. In case of paintings up to 200 µm no electrostatic load can be expected. Multiple coatings exceeding a thickness of 200 µm are prohibited for explosion group llC. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 18 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.7 Breakdowns, Causes and Elimination The below-mentioned errors can lead to an incorrect use of the BoWex-ELASTIC® coupling. In addition to the stipulations in these operating and mounting instructions please make sure to avoid these errors. The errors listed can only be clues to search for the errors. When searching for the error the adjacent components must be generally included. Due to incorrect use the coupling may become a source of ignition. EC Standard 94/9/EC requires a special care from the manufacturer and the user. General errors of incorrect use Important data for the coupling selection were not forwarded. The calculation of the shaft/hub connection was not considered. Coupling parts with damage occurred during transport are assembled. If the heated hubs are assembled, the permissible temperature is exceeded. The fits of the parts to be assembled are not coordinated with each other. Tightening torques are fallen below/exceeded. Components are replaced by mistake/put together incorrectly. No original KTR parts (purchased parts) are used. Old elastomer parts/already worn out elastomer parts or elastomer parts that were stored too long are used. The coupling used/the coupling protection used is not suitable for the operation in hazardous areas and does not correspond to EC Standard 94/9/EC, respectively. Maintenance intervals are not observed. breakdowns change of the running noises and / or occurring vibrations break of the elastomer part / toothing Please note protection mark ISO 16016. hints to danger for hazardous areas causes misalignment micro friction at the toothing of the elastomer part danger of ignition due to hot surfaces loose screws for axial securement of hubs danger of ignition due to hot surfaces break of the elastomer part / toothing due to high shock energy / overload Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz --- elimination 1) put the unit out of operation 2) eliminate the reason for the misalignment (e. g. loose foundation bolts, fracture of the engine fixing, heat expansion of unit components, change of the assembly dimension E of the coupling) 3) checking of wear see under point 5.4 1) put the unit out of operation 2) check alignment of coupling 3) tighten the screws to secure the hubs and secure against self-loosening 4) checking of wear see under point 5.4 1) put the unit out of operation 2) disassemble the coupling and remove remainders of the elastomer part 3) check coupling parts and replace damaged coupling parts 4) insert elastomer part, assemble coupling parts 5) find out the reason for overload Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 19 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.7 Breakdowns, Causes and Elimination breakdowns hints to danger for hazardous areas causes operating parameters do not correspond to the performance of the coupling --- mistake in service of the unit --- drive vibrations danger of ignition due to hot surfaces break of the elastomer part / toothing ambient / contact temperatures which are too high for the excessive wear at elastomer part, max. the elastomer part / permissible toothing e. g. T4 = -30 °C / +100 °C danger of ignition due to hot surfaces e. g. contact with aggressive liquids / oils, ozoneinfluence, too high ambient temperatures etc. effecting a physical change of the elastomer part --- elimination 1) put the unit out of operation 2) check the operating parameters and select a larger coupling (consider installation space) 3) assemble new coupling size 4) check alignment 1) put the unit out of operation 2) disassemble the coupling and remove remainders of the elastomer part 3) check coupling parts and replace damaged coupling parts 4) insert elastomer part, assemble coupling parts 5) instruct and train the service staff 1) put the unit out of operation 2) disassemble the coupling and remove remainders of the elastomer part 3) check coupling parts and replace damaged coupling parts 4) insert elastomer part, assemble coupling parts 5) check alignment, correct if necessary 6) find out the reason for the vibrations 1) put the unit out of operation 2) disassemble the coupling and remove remainders of the elastomer part 3) check coupling parts and replace damaged coupling parts 4) insert elastomer part, assemble coupling parts 5) check alignment, correct if necessary 6) check and regulate ambient / contact temperature 1) put the unit out of operation 2) disassemble the coupling and remove remainders of the elastomer part 3) check coupling parts and replace damaged coupling parts 4) insert elastomer part, assemble coupling parts 5) check alignment, correct if necessary 6) make sure that further physical changes of the elastomer part are excluded If you operate with a worn elastomer part (see item 5.2) a proper operation meeting the explosion protection requirements and acc. to Standard 94/9/EC is not ensured. ATTENTION! KTR does not assume any liabilities or warranties regarding the use of spare parts and accessories which are not provided by KTR and for the damages resulting herefrom. Please note protection mark ISO 16016. Drawn: Verified: 08.11.11 Pz/Hk 09.11.11 Pz Replaced for: Replaced by: KTR-N valid from 08.04.04 KTR Kupplungstechnik GmbH D-48407 Rheine BoWex-ELASTIC® Operating/Assembly Instructions Type HEW and HEW-ZS KTR-N Sheet: Edition: 40114 EN 20 of 20 5 5 Enclosure A Hints and Instructions Regarding the Use in Hazardous Areas 5.8 EC Certificate of Conformity EC Certificate of Conformity corresponding to EC Standard 94/9/EC dated 23 March 1994 and to the legal regulations The manufacturer - KTR Kupplungstechnik GmbH, D-48432 Rheine - states that the BoWex-ELASTIC - highly flexible flange couplings described in these mounting instructions and designed for explosion protection correspond to Article 1 (3) b) of Standard 94/9/EC and comply with the general Safety and Health Requirements according to enclosure II of Standard 94/9/EC. The BoWex-ELASTIC® is in accordance with the specifications of the standard 94/9/EC. One or several standards mentioned in the corresponding EC type test certificate IBExU01ATEXB004_05 X were in part replaced by updated versions. KTR Kupplungstechnik GmbH as the manufacturer confirms that the product mentioned above is in accordance with the specifications of the new standards, too. According to article 8 (1) of Standard 94/9/EC the technical documentation is deposited with the: IBExU Institut für Sicherheitstechnik GmbH Fuchsmühlenweg 7 09599 Freiberg Rheine, Please note protection mark ISO 16016. 08.11.11 Date Drawn: Verified: i. V. Reinhard Wibbeling Engineering Manager 08.11.11 Pz/Hk 09.11.11 Pz i. V. Josef Schürhörster Product Manager Replaced for: Replaced by: KTR-N valid from 08.04.04 ">

Public link updated
The public link to your chat has been updated.
Advertisement