HPRT Alpha User Manual
PDF
Download
Document
Advertisement
Advertisement
Alpha User Manual Xiamen Hanin Electronic Technology Co., Ltd. ADD:5F, 8#, Aide Airport Industrial Park, Huli District, Xiamen, China. WEB:www.idprt.com Rev.1.0 Alpha User Manual Contents Important Safety Instructions .............................................................................................................. 1 Chapter 1 Introduction ......................................................................................................................... 4 1.1 Packing List ............................................................................................................................. 4 1.2 Appearance and Components ................................................................................................ 5 1.3 Dimension .............................................................................................................................. 7 Chapter 2 Specifications....................................................................................................................... 8 Chapter 3 Installation & Usage .......................................................................................................... 11 3.1 Media Loading ...................................................................................................................... 11 3.1.1 Loading the Roll ......................................................................................................... 11 3.1.2 Loading the Ribbon ................................................................................................... 13 3.2 Power Connection ................................................................................................................ 16 3.3 Peripherals Connection ........................................................................................................ 17 3.3.1 Interface Cable Connection ....................................................................................... 17 3.3.2 Bluetooth Connection ............................................................................................... 17 3.4 Detection .............................................................................................................................. 18 3.4.1 Continuous Paper ...................................................................................................... 18 3.4.2 Labels ........................................................................................................................ 20 3.4.3 Punched Hole Label................................................................................................... 22 3.4.4 Blackmark Paper........................................................................................................ 23 3.5 Operation Panel ................................................................................................................... 24 3.5.1 Panel Introduction..................................................................................................... 24 3.5.2 Indicator Instructions ................................................................................................ 25 3.6 Basic Function ...................................................................................................................... 26 3.6.1 Power on/ Power off ................................................................................................. 26 3.6.2 FEED Button .............................................................................................................. 26 3.6.3 Quick Calibration ....................................................................................................... 26 3.6.4 Print Self-test Page .................................................................................................... 27 Chapter 4 Interface ............................................................................................................................ 28 4.1 USB Interface ........................................................................................................................ 28 4.2 Other Optional Interfaces .................................................................................................... 29 Chapter 5 Maintenance & Adjustment ............................................................................................... 31 5.1 Cleaning Media Sensor......................................................................................................... 31 5.2 Cleaning Thermal Print Head ............................................................................................... 31 5.3 Cleaning Roller and/or Paper Path ....................................................................................... 32 Chapter 6 Printer Utility Tool Instructions ......................................................................................... 33 6.1 Installation Preparation ........................................................................................................ 33 6.2 Usage .................................................................................................................................... 33 Chapter 7 Seagull Windows Driver Instructions ................................................................................ 50 7.1 Introduction ......................................................................................................................... 50 7.2 Installation Preparation ........................................................................................................ 50 7.3 Installation ............................................................................................................................ 51 7.4 Usage .................................................................................................................................... 56 Alpha User Manual 7.4.1 Printing Preferences .................................................................................................. 56 7.4.2 Printer Properties ...................................................................................................... 71 Chapter 8 BarTender Ultralite Instructions ........................................................................................ 75 8.1 Introduction ......................................................................................................................... 75 8.2 Installation Preparation ........................................................................................................ 75 8.3 Installation ............................................................................................................................ 76 8.4 Usage .................................................................................................................................... 80 8.4.1 Page Settings ............................................................................................................. 80 8.4.2 label Edit.................................................................................................................... 89 Alpha User Manual ◼ Statement This manual content may be altered without permission, and our company reserves the rights to make changes without notice in technology, spare parts, hardware and software of the products. If more information is needed about the products, please contact our company. Without any written permission from our company, any section of this manual is prohibited to be copied or transferred in any form. ◼ Copyright This manual is printed in 2019, the copyright belongs to Xiamen Hanin Electronic Technology Co., Ltd. Printed in China 1.1 Version ◼ Warnings This must be complied with in order to avoid any damage to the human body and the equipment. This is showing the important information and tips for the printer operation. oote Due to continuous update of our product, the description of printer specification, accessories, design in this manual may be slightly different. Please keep in kind prevail. Alpha User Manual Important Safety Instructions Before using the appliance, please carefully read the following safety regulations in order to prevent any hazard or material damage. 1. Safety warning Warnings: The print head will become very hot during printing; avoid contact with the print head after printing has finished. Warnings: Do not touch the printer head and connector in case static damage the printer head. 2. Instructions Warnings Violating following instructions can cause serious injury or death. 1) Do not plug several products in one multiperture outlet. • This can provoke over-heating and a fire. • If the plug is wet or dirty, dry or wipe it before usage. • If the plug does not fit perfectly with the outlet, do not plug in. • Be sure to use only standardized multiperture outlet. 2) You must use the supplied adapter. • It is dangerous to use other adapters. 3) Do not pull the cable to unplug. • This can damage the cable, which is the origin of a fire or a breakdown of the printer. 4) Do not plug in or unplug with your wet hands. • You can be electrocuted. 5) Do not bend the cable by force or leave it under any heavy object. • A damaged cable can cause a fire. 1 Alpha User Manual oote Violating following instructions may cause slight damage of the appliance. 1) If you observe a strange smoke, odour or noise from the printer, unplug it before taking following measures. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. 2) Install the printer on the stable surface. • If the printer falls, it can be broken and you can hurt yourself. 3) Use the approved accessories only and do not try to disassemble, repair or remodel it by yourself. • Call your dealer when you need these services. • Do not touch the blade of auto cutter. 4) Do not let water or other foreign objects drop into the printer. • If this happened, switch off and unplug the printer before calling your dealer. 5) Do not use the printer when it is out of order. This can cause a fire or an electrocution. • Switch off and unplug the printer before calling your dealer. 6) Other considerations: • Place the printer on a solid and even base so that it cannot fall. • Leave enough space around printer for operation and maintenance. • Keep all liquids away from the printer. • Do not expose the printer to high temperatures, direct sunlight or dust. • Ensure the printer is connected to a socket with the correct mains voltage. • Switch off the printer POWER supply when it’s not in use for a long time. • To ensure the printing quality and reliability, suggest use the same quality or recommend paper supplier. • Pls. switch off the POWER supply when connect/disconnect all the ports or it will cause damage to the printer control circuit. • Never carry out maintenance or repair work yourself. Always contact a qualified service Technician. • Keep this User Manual in a place which is always easily accessible. 2 Alpha User Manual 3. Other Precautions The copyright for this user manual and various other manuals is property of our company. Any copying or conversion into electronic form and saving of this material without the express written permission is strictly prohibited. Use of the information contained in this manual is not subject to any patent liability. This manual has been prepared with utmost care and attention to detail but may contain certain errors and/or omissions. Our company is not legally liable for any damages resulting from the use of the information in this manual. Our company and its affiliates are not legally liable (United States excluded) for any damages, loss, costs, and/or expenses that result from the breakdown, malfunction, and/or misuse of the product due to violation or neglect of the operation and maintenance information and instructions provided by our company, as well as from the unauthorized alteration, repair, and/or modification of the product by the user and/or third party. We are not legally liable for any damages and/or issues resulting from the use of options and/or parts that are not authentic or authorized products. 4. WEEE (Waste Electrical and Electric Equipment) This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office for details of where and how they can conduct environmentally safe recycling of such items. Commercial users should contact their suppliers and check the terms and conditions of purchase contracts. This product should not be combined with other commercial waste for disposal. Caution This is a Class A product. In a domestic environment this product may cause radio interference in which the user may be required to take adequate measures. 3 Alpha User Manual Chapter 1 Introduction 1.1 Packing List 1. Unpack the printer and keep the packing material in case you need to ship the printer in the future. 2. Any damages exist, please contact the local dealer. oote The packing materials are based on the order. 4 Alpha User Manual 1.2 Appearance and Components ■Front View ■Rear View 5 Alpha User Manual ■Inside View oote The views above are for your reference. Ports vary by your choice. 6 Alpha User Manual 1.3 Dimension Take printer Alpha as example. 7 Alpha User Manual Chapter 2 Specifications Item Printing Parameter Printing Method Thermal transfer/Direct thermal Resolution STD 203dpi,OPT 300dpi Max.Printing Speed Max.Printing Width Max.Pringting Length Memory 5 ips (203dpi) 4 ips (300dpi) 108 mm(203dpi),106 mm(300dpi) 2,286 mm(203dpi),1,524 mm(300dpi) RAM 128MB Flash 256MB Programming Language ZPL-II,EPL-II,DPL Print Frame Open Detect, Ribbon End Detect, Paper Out Detection Sensor Detect, TPH Over Heating Detect,2 Fixed See-through sensor, Full Range Reflective Sensor Types Media Ribbon 1''(25.4)-4.65''(118 mm), include the liner Thickness 0.002''(60um)-0.01''(250um) Label Roll Diameter 5''(127 mm) Max Core Diameter 0.5''(12.7 mm), 1''(25.4 mm). 1.5''(38 mm) Type Wax, Wax/Resin, Resin Width 1.18''(30 mm)-4.33''(110 mm) Length 328'(100 m) Core Diameter 0.5''(12.7 mm) Software Driver Resident Fonts Label Width Label Design Software Continuous Paper, Gap, Black Mark, Punched Hole HPRT Bartender Ultralite Windows 7,8,10, server 2008,2012 CUPS for Linux and MAC OS 6, 8, 12, 16, 32, OCR A & B. Bitmap fonts 90°, 180°, 270° rotatable and 10 times expandable in horizontal and vertical directions 8 Alpha User Manual Monotype CG Triumvirate™. 0°, 90°, 180°, 270° TTF fonts Item Parameter Bitmap fonts 90°, 180°, 270° rotatable and 10 times expandable in horizontal and vertical directions 16x16, 24x24. Traditional Chinese, Simplified Chinese, Japanese, Download Fonts rotatable Asian fonts Korean, 90∘,180∘,270∘, rotatable and 8 times expandable in horizontal and vertical directions TTF fonts 90°, 180°, 270° rotatable Code 39, Code 93, EAN 8/13 (add on 2 & 5), UPC A/E (add on 2 & 1D Barcodes 5), I 2 of 5, Codabar, Code 128 (subset A, B, C), EAN 128, MSI, Plessey, Telepen, GS1 DataBar, Standard 2 of 5, Industrial 2 of 5, Code 11, Code 49 2D PDF417, Data matrix code, QR code, Micro PDF417, Aztec code 850, 852, 437, 860, 863, 865, 857, 861, 862, 855, 866, 737, 851, 869, WINDOWS 1250, 1251, 1252, 1253, 1254, 1255, 1257, Code Pages UTF-8, UTF-16BE, UTF-16LE, DBCS 932 (JIS), 936(GBK), 949 (Koran), 950(BIG5) Resident graphic file types are BMP and PCX, other graphic formats Graphics Interfaces are converted by the software download Standard USB Optional RS232, Ethernet, Wi-Fi, Bluetooth Control Panel Power switch button, FEED button, 2 indicating LEDs External AC/DC switching power adapter, AC 100V-240V/DC Power Supply Environment Physical Characteristic 24V/2A/48W, Peak 5A Operation 5 to 50℃@ humidity 25% to 85% non-condensing Storage -40 to 60℃@ humidity 10% to 90% non-condensing Dimension (L*H*W) Weight 252*201*181 mm About 1.8 kg Options & Accessory Peeler Module, Cutter Module, External Label Roll Holder Agency Approval CE EMC (EN 55022 Class B), FCC EMC (Class A), CCC, RoHS 9 Alpha User Manual 10 Alpha User Manual Chapter 3 Installation & Usage 3.1 Media Loading 3.1.1 Loading the Roll 1.Pull and lift the cover. (e.g.: Alpha) 2.Pull the roll holders open and place the roll between them, then press down the locking tab. 11 Alpha User Manual 3.Press down the locking tab. 4.Pass the labels through label guides and adjust label guides to adapt to the label width. oote If your printer is under Thermal Line Printing Method, press down the printer cover until it snaps closed. Otherwise, continue the procedure in chapter 3.1.2. 12 Alpha User Manual 3.1.2 Loading the Ribbon 1.Insert the right part of supply spindle and then the left part. 2.Press and release the printhead module. 13 Alpha User Manual 3.Insert the right part of rewind spindle and then the left part. 4.Rotate the ribbon rewind wheel until ribbon is pulled tightly. 14 Alpha User Manual 5.Close the printhead module. Then press the lock and close the cover slightly. 6.Press down the cover until it snaps closed. 15 Alpha User Manual 3.2 Power Connection 1.Connect the AC adapter to power receptacle. 2.Connect the power cord to AC adapter. 3.Connect the other end of power cord to the outlet. Caution: ⚫ Use the original power adapter only. Avoid the damage caused by charging improperly. ⚫ Please unplug the printer power cord if it is not in use for a long time. 16 Alpha User Manual 3.3 Peripherals Connection 3.3.1 Interface Cable Connection 1.The standard for the printer’s interface cable shows as follows: - USB A-Type cable - USB B-Type cable - RS-232C cable - RJ45 cable 2.Based on your own need, follow the instructions to connect the cable. 1) Make sure the printer’s power is off. 2) Please plug in the cables. -Insert the USB A-Type cable into the USB (type A) interface. -Insert the USB B-Type cable into the USB (type B) interface. -Insert the RS-232C cable into the serial interface. -Insert the RJ45 cable into the ethernet interface. 3.3.2 Bluetooth Connection PDA with Bluetooth interface, laptop and other information terminals can drive the printer. Instructions show as follows: 1. Power on the printer. 2. Primary device searches for outer Bluetooth devices. 3. If there are other Bluetooth devices, select printer’s name. 4. Finish pairing. If you need more detailed information of pairing methods, please refer to the instructions of Bluetooth device. After pairing, primary devices with virtual Bluetooth interface (smart phone, tablet, pocket PC, palm, notebook) can drive the printer to print labels through virtual Bluetooth interface. oote The original code is 0000. 17 Alpha User Manual 3.4 Detection When printing paper, the moveable label sensor is used to detect paper. The label sensor moves differently when using various kinds of paper. If user moves the sensor improperly, paper may not be detected, therefore the printer could not print paper. The following instructions tell users how to use label sensor correctly. Please read it carefully. 3.4.1 Continuous Paper When printing continuous paper (Figure 1), the sensor shall be aimed at the left triangle below (Figure 2), which is the original position. Figure 1 (Continuous Paper) 18 Alpha User Manual Figure 2 (Left) 19 Alpha User Manual 3.4.2 Labels When printing labels (Figure 3) or double-row labels (Figure 4), the sensor shall be aimed at the left triangle below (Figure 5), which is the original position. Figure 3 (Labels) Figure 4 (Double-row Labels) 20 Alpha User Manual Figure 5 (Left) 21 Alpha User Manual 3.4.3 Punched Hole Label When printing punched hole labels, move the sensor until it’s aimed at the right triangle below (Figure 6). Figure 6 (Right) 22 Alpha User Manual 3.4.4 Blackmark Paper When printing blackmark paper (Figure 7), the sensor shall be aimed at the position of black mark (Figure 8). Figure 7 (Blackmark Paper) Figure 8 (aimed at blackmark’s position) 23 Alpha User Manual 3.5 Operation Panel 3.5.1 Panel Introduction The panel indicates the printer’s operating status and allows the user to control basic printer operation. 1.Power Button Much more detailed information is provided in “3.6.1 Power On/ Power Off”. 2.Feed Button Much more detailed information is provided in “3.6.2 FEED Button”. 24 Alpha User Manual 3.5.2 Indicator Instructions 1.Power Light Color Action Indicating Status x x The printer is off Green On Normal operation Green Slow flash Dump mode 2.Status Light Color Action Indicating Status x x The printer is off/standby/printing Red On Head up/paper out Red Quick flash Paper jam/label’s separation Orange On Ribbon out Orange Slow flash Printing pause Green On Label calibration Green Slow flash Wait on demand Green Quick flash Receiving data 3.Paper Container Light Action Indicating Status On Paper out/Paper jam/label’s separation Off Head up/error elimination oote Quick flash → 0.2 second / every cycle Slow flash → 1 second / every cycle 25 Alpha User Manual 3.6 Basic Function 3.6.1 Power on/ Power off ⚫ ⚫ When the printer is off, press the power button once, and printer will power on. When the printer is on, press the power button for three seconds. After ringing twice, the printer will power off. 3.6.2 FEED Button ⚫ ⚫ ⚫ ⚫ ⚫ When the printer is ready, press the feed button, and printer will automatically feed a label under “Label Mode”. Press the feed button, and the printer will feed the fixed distance under “Continuous Mode”. When the printer is printing, press the feed button once and it will stop the printing job. Press the feed button for three seconds and it will cancel the printing job. When the printer pauses, press the feed button once and it will continue the printing job. Press the feed button for three seconds and it will cancel the printing job. When the printer is in dump mode, press the feed button once, then back to the normal printing mode. When the indicator status flashes slowly(green), press the feed button once and printer will print a label. 3.6.3 Quick Calibration Users must carry out the calibration under the conditions below: ➢ The first time to use the printer since installation; ➢ The first time to use the printer since sensor cleaning; ➢ Reuse the printer when it has not been used for a long time; ➢ Change a new type of media; ➢ Printer cannot recognize the mark; ➢ Huge change of the operating environment; Calibration method ⚫ Carry out the calibration manually. When printer is ready, press the FEED button for 3 seconds until the status indicator (Green) flashes twice. Then release the button, and printer will start to do the calibration. When printer does the calibration under Continuous Media Mode, the calibration is invalid. ⚫ Carry out the calibration by printer utility tool. Please refer to detailed information in “Chapter 6 Printer Utility Tool Instructions”. Note: After the quick calibration, users could open the printer cover to pull back the learned paper in avoid of paper wasting. 26 Alpha User Manual 3.6.4 Print Self-test Page The self-test checks the printer’s current settings, status and whether the printer has any problems or not. 1.Printing Manually 1) Make sure the roll is loaded properly. 2) Make sure the top cover of the printer is closed properly. Then turn on the printer. 3) When the printer is ready, press the feed button continuously. As soon as the indicator flashes (green) once, loosen the button. Then the printer starts to print the self-test page. 2.Printing by Windows Driver Program 1) Install the Windows Driver program. 2) Set the “Interface” as the type you use. 3) Use the Windows Driver Program to print out the “Self-test page”. 4) Please refer to “Chapter 7 Seagull Windows Driver Instructions” for more detailed information. 3.Printing by BarTender Ultralite Program 1) Install the BarTender Ultralite program. 2) Edit a new label and print it. 3) Please refer to “Chapter 8 BarTender Ultralite Instructions” for more detailed information. 27 Alpha User Manual Chapter 4 Interface 4.1 USB Interface 1.USB (Type A) PIo 1 2 3 SIGoAL oAME VBUS DD+ 4 GND PIo 1 2 3 SIGoAL oAME VBUS DD+ 4 GND 2.USB (Type B) 28 Alpha User Manual 4.2 Other Optional Interfaces ◼ Serial Port PIo 1 2 3 4 5 6 7 8 9 SIGoAL oAME +5VDC RXD TXD DTR GND DSR RTS CTS - SIGoAL DIRECTIOo OUTPUT OUTPUT INPUT INPUT GROUNDING OUTPUT INPUT OUTPUT NO CONTACT ◼ Ethernet Port PIo 1 2 3 4 5 6 7 8 SIGoAL oAME TX+ TXRX+ RX29 Alpha User Manual 30 Alpha User Manual Chapter 5 Maintenance & Adjustment Adhesives and coatings of the media can transfer to the printer parts over time along the media path including the thermal print head and media sensor. This build-up can accumulate dust and debris. Failure to clean the print head, media path, and media sensor could result in inadvertent loss of labels, label jams and possible damage to the printer. ⚫ ⚫ ⚫ ⚫ oote Make sure to turn off the printer prior to cleaning. As the print head gets hot during printing, if intending to clean the print head, turn the printer off and wait approximately 2~3 minute before commencement. When cleaning the print head, take care not to touch the heated portion of the print head. Print Head is susceptible to damage from static electricity, etc. So it is strongly recommended to wear hand gloves during cleaning progress. Take care not to allow the print head become scratched and/or damaged in any way. 5.1 Cleaning Media Sensor Debris or dirt on the paper sensor can cause a miss-read or unstable detection of the label gap. Clean with a cotton bud dampened with alcohol. 5.2 Cleaning Thermal Print Head Thermal Paper stock on the print head, which degrades print quality. Clean the print head with methanol or isopropyl alcohol and a cotton bud. Do not touch the heating elements with your fingers. 1) Open the Printer Cover and then use the cleaning pen to clean the head in the direction from the center of the head to two sides. 2) After cleaning the head, do not use the printer until the alcohol used for cleaning evaporates completely (1~2 min) and the printer has completely dried. 3) Perform the cleaning process each time the paper roll is replaced to prevent print quality deterioration. 31 Alpha User Manual 5.3 Cleaning Roller and/or Paper Path 1) Open the printer cover and then remove the paper. 2) Remove any dust or foreign substance using dry cloth or cotton swab. 3) Soak the cloth or cotton swab in alcohol for medical use and use it to remove adhesive foreign substances or other pollution materials. 4) After cleaning the parts, do not use the printer until the alcohol evaporates completely (1~2 min) and the printer has completely dried oote Clean the parts when print’s quality or label detection degrades. 32 Alpha User Manual Chapter 6 Printer Utility Tool Instructions 6.1 Installation Preparation Download application program in CD. e.g.: Utility.exe 6.2 Usage ⚫ ⚫ oote The screen may vary slightly by different operating systems and models. Take printer Alpha as example. 1.Install “Utility.exe”, then open it. 33 Alpha User Manual 2.Click “Settings”. (1) Set up the interface needed. (range: USB, COM, LPT, ETH) 34 Alpha User Manual (2) Click “Get Printer Information”, and printer information will show in the above. 35 Alpha User Manual (3) Click “Get Status”, and printer status will show in the above. 36 Alpha User Manual (4) Click “Common”. In this menu, user can set up the protocol, media sensor, speed, density and so on. 37 Alpha User Manual (5) Click “RS-232”, then set up the baud rate, data bits, parity and flow control. 38 Alpha User Manual (6) Click “Bluetooth”, then set up the Bluetooth name and password. Click “Get” to gain the values of Mac address. 39 Alpha User Manual (7) Click “Ethernet”, then click “Get” to gain the relevant values. 40 Alpha User Manual (8) Click “WIFI”, then set up the name, password and so on. 41 Alpha User Manual oote ① Finishing all the settings, user can click “Set” to save the values changed. ② Click “Get”, and user will get the default values. 42 Alpha User Manual 3.Click “Storage” to print image. (1) Click "File name" to select the image. oote The file name must be in English or number, and the filename length must be less than 32. 43 Alpha User Manual (2) Click “Download”. (3) Select the downloaded graphic, and then click “print selected graphic” to print the picture. 44 Alpha User Manual (4) You can set a magnification of the graphic as needed. 45 Alpha User Manual 4.Click "Download Vector fonts". (1) Click "Select Font" to select the vector font you want. (2) Click "Download" (Note: The font file name must be in English or number). 46 Alpha User Manual (3) Select the downloaded font file, enter the print content in the text box, and click “Print Text”. 47 Alpha User Manual 5.Click “Function Test”. User can carry the followings such as sensor calibration, pattern print testing and so on. 48 Alpha User Manual 6.Click “System”. Click “language” and choose the language of printer utility. 49 Alpha User Manual Chapter 7 Seagull Windows Driver Instructions 7.1 Introduction ⚫ Windows Vista,Windows 7,Windows 8 and 8.1,and Windows 10. ⚫ Windows Server 2008,2008 R2,2012,2012 R2,and 2016. ⚫ 32-bit and 64-bit(x64)editions. 7.2 Installation Preparation Download Seagull Windows Driver application program in CD. 50 Alpha User Manual 7.3 Installation ⚫ ⚫ ⚫ oote Under different operating systems, the screen may be slightly different. Take Windows 10 as example. Take printer Alpha as example. To avoid the prevention, recommend to close the security software before installation. 1.Select one interface to connect your printer to computer. 2.Turn on the printer and check if it is connected to computer successfully. 3.Double click Seagull Windows Driver . 4.Read and agree the license agreement. Then click “Next”. 51 Alpha User Manual 5.Choose the installation directory, then click “Next”. 6.Click "Finish". 52 Alpha User Manual 7.Choose "Install printer drivers", then click "Next". oote If you have connected the printer to computer, it will detect and install the driver automatically. (e.g. USB port) 8.Choose "Specify Printer Model”, then click "Next". 53 Alpha User Manual 9.Enter a name for this printer, then click "Next". 10.Click"Finish". 54 Alpha User Manual 11.Click "Close", and the driver is installed successfully. 12.After installation, the icon will be found in “Start” → “Devices and Printers”. ⚫ ⚫ oote If you have already installed the driver (oo matter what kind of ports), it will generate a USB port automatically when connecting the printer to computer. Any problems exist, please use our utility tool in CD. 55 Alpha User Manual 7.4 Usage 7.4.1 Printing Preferences 1.Click “Start” → “Devices and Printers”. Right click the icon and choose “Printing preferences”. 56 Alpha User Manual 2.According to different needs, set up the page. 57 Alpha User Manual ●Click “Stock” → “Name”, and choose the paper type. 58 Alpha User Manual 59 Alpha User Manual ●Click “New Stock”, and set up a new stock. ●Click “Edit Stock”, and edit the stock. 60 Alpha User Manual 61 Alpha User Manual ●Click “Delete Stock”, and delete the stock. ●Choose “Orientation” or “Effects”, showed in the “Preview”. 62 Alpha User Manual ●Click “Preset” → “Name”, and back to the default settings. 63 Alpha User Manual ●Click “Manage”, and change the settings. 64 Alpha User Manual 3.Click “Graphics”, and edit the pictures. 65 Alpha User Manual 4.Click “Stock”. 66 Alpha User Manual ●Click “Print Method”, and choose the printing method. 67 Alpha User Manual 68 Alpha User Manual ●Set up the media type. 69 Alpha User Manual ●Click “Feed Mode” → “Mode”, and choose the method of media handing. 70 Alpha User Manual 7.4.2 Printer Properties 1.Click “Start” → “Devices and Printers”. Right click the icon and choose “Printer properties”. 71 Alpha User Manual 72 Alpha User Manual 2.Click “General” → “Print Test Page”, and printer will print labels with current settings. 73 Alpha User Manual 3.Click “Ports”, and choose the port needed. 74 Alpha User Manual Chapter 8 BarTender Ultralite Instructions 8.1 Introduction This chapter provides instructions on BarTender Ultralite program according to PC operating systems(OS). The followings are supported. ⚫ Windows 10, 8.1, 8, 7 and Vista. ⚫ Windows Server 2016,Server 2012 and 2012 R2,Server 2008 and 2008 R2. ⚫ Includes all 32-bit and 64-bit(x64)editions. 8.2 Installation Preparation Download BarTender Ultralite application program in CD. 75 Alpha User Manual 8.3 Installation oote: ⚫ ⚫ ⚫ Under different operating systems, the screen may be slightly different. Take Windows 7 as example. Take printer Alpha as example. Please refer to printer Alpha when using printer Alpha. To avoid the prevention, recommend to close the security software before installation. 1.Double click the application program . 2.Select language, then click "OK". 3.Click "Install". 76 Alpha User Manual 4.Click “Next”. 5.Read and accept the license agreement, then click "Next". 77 Alpha User Manual 6.Select "Features" and installation location, then click "Next". 7.Click "Install". 78 Alpha User Manual 8.Click "Finish". 9.Back to desktop, and you will see the icon of BarTender. Double click it and get down to use. 79 Alpha User Manual 8.4 Usage 8.4.1 Page Settings 1.Double click the icon, then choose the edition. Click “OK”. (The edition may be changed according to different needs.) 2.Click “Start a new BarTender document”. 80 Alpha User Manual 3.Choose “Blank Template”, then click “Next”. 81 Alpha User Manual 4.If the predefined stocks don’t meet your need, tick “Specify Custom Settings”. Then click “Next”. 82 Alpha User Manual 5.Tick “Single item per page”, then click “Next”. (If you print multiple labels, tick “Multiple columns and/or rows of items per page”.) 83 Alpha User Manual 6.Edit the side edges, then click “Next”. 84 Alpha User Manual 7.Choose the item shape, then click “Next”. 85 Alpha User Manual 8.Edit the template size, then click “Next”. 86 Alpha User Manual 9.Based on your need, edit the template background. Then click “Next”. 87 Alpha User Manual 10.Finish the settings, showed in the “Review” and “Preview”. Then click “Finish”. 88 Alpha User Manual 8.4.2 label Edit 1.Click the icon of code . 2.Choose the code, then click “Select”. 3.Click the blank, showing the code. 89 Alpha User Manual 90 Alpha User Manual 4.Double click the code and edit it. User can set up the size, font, border and so on. Finishing the change, click “Close”. 91 Alpha User Manual 5.Click the icon of character , then enter the text. 6.Click the icon of picture , then edit the pictures. 92 Alpha User Manual 7.Compose the text. 8.Finish all the settings. Click “Print” and a new label will be printed. 93 ">

Public link updated
The public link to your chat has been updated.
Advertisement