User Manual
Access Control Software
Instruction
Contents
Copyright owns by © 2006 PEGASUS Software Inc. All right
reserved
·Information in this document is subject to change
without notice.
·PEGASUS Software Inc. is a registered trademark
of PEGASUS Software Corporation, Biokey is a core
technical logon of PEGASUS Software Inc,
PEGASUS Software, Biokey has been registered in
the china and the U.S.A
·Other trademark and trade name may be used in this
document to refer to either the entities claiming the
mark and names or their products, PEGASUS
Software Inc disclaims any proprietary interest in the
trademark and trade name other than its own.
1
Access control software introduction
Contents
1. Installation and Uninstall ......................................................... 7
1.1 Installs software............................................................. 7
1.2 Uninstall software .........................................................12
2.1.1 Communication Setup ...................................................... 14
2.1.2 Fingerprint Machine Information ....................................... 17
2.1.3 Wiegand .......................................................................... 18
2.1.4 Verification ....................................................................... 20
2.1.5 Power Management ......................................................... 21
2.1.6 Access Control ................................................................. 22
2.1.7 Mifare Card ...................................................................... 23
2.1.8 Other Setup ..................................................................... 24
2.2 Department Management .............................................25
2.3 User Management ........................................................27
2.4. Load from the USB flash disk ......................................37
2.5 Management USB Flash Disk .......................................38
2.5.1 Load in the User Data ...................................................... 38
2.5.2 Export user data............................................................... 39
2.6 System Setup ...............................................................40
2.6.1 Automatic monitoring ....................................................... 41
2.6.2 Parameter of Server ......................................................... 42
2.6.3 Function Configuration ..................................................... 42
3. Access Control Setup ............................................................43
3.1 Period Time ..................................................................43
3.2 Group ...........................................................................44
Group Setting ........................................................................... 45
3.3 Unlock Combination .....................................................47
3.4 User Privileges .............................................................48
3.5Holidays setting .............................................................57
4. Base Operation .....................................................................62
4.1 Upload Setting ..............................................................62
4.2 Upload Equipment .............................................................. 62
4.2 Open Door....................................................................65
4.3 Starting/Stopping Monitoring.........................................65
5. Query ....................................................................................66
5.1 Record Query ...............................................................66
5.2 Alarm Record ...............................................................67
-2-
Access control software introduction
6. System Management.............................................................68
6.1 Operator Management .................................................68
6.2 System Operation Log ..................................................69
6.3 Data Maintenance ........................................................70
6.3.1 Backup Database............................................................. 70
6.3.2 Database Compress ........................................................ 71
6.3.3 Clear Old Data ................................................................. 71
6.4 Initialize System ...........................................................72
6.5 Set Database ...............................................................73
6.6 Set Password of Database ...........................................75
-3-
Access control software introduction
About Software
Fingerprint Access Control, Access Control based on
biometric solution from PEGASUS Software is designed to
help you with all solution which can be use with access
control system to limit the areas where each person is
authorized to go, it might every be good to know where an
individual has been.
Who is still doubt, among various biometric systems, the
fingerprint recognition system takes up most of the market,
because it is easy to use as well as economical and capable of
developing various types of applications. The current software
version is Version 2.0 and its main functions are as follows:

Multi-terminal networking, real-time monitoring 
No matter Ethernet connection or 485 connections,
fingerprint machine can be added into management
software. After all fingerprint machines are added, click Start
Monitoring and the system will start relative monitoring from
the first unit to the last unit.

Real-time record download 
Fingerprint records on each fingerprint machine can be
downloaded in real time. After download, these records will
be stored in database automatically. If there is a attendance
software, you can set database directory of attendance
software as directory of the database to store these records.
Then you can check attendance records at any time.

Search records and output records in various formats 
When there are many fingerprint records, you can search records.
During search, various condition search functions are defined, such
as ID of fingerprint machine, time period, department, etc. Also
records can be outputted in various formats.

Upload Access control setting 
This function is to upload basic Access control setting and
user Access control setting.
-4-
Access control software introduction

Department management 
After created department, in User Management you can
assign employees to corresponding department.

User management 
This function mainly includes downloading user and
fingerprint, editing user’s information and privilege, creating
password for user, using ―U are U fingerprint sensor‖ to add
new user, uploading user and fingerprint.

Remote open door 
In program, you can click Open Door button to remote unlock
the selected door

Synchronizing time 
Synchronize time of fingerprint machines.

Upgrading firmware 
Upgrade the firmware of fingerprint machine.

Initialize fingerprint machine 
In device management, you can initialize fingerprint machine.
-5-
Access control software introduction



Operation procedure steps as follow: 
Hardware connection 
This is the first step. Connect all fingerprint machines and PC
together. Use RS232 cable to connect when distance doesn’t
exceed 15 meters. Under the condition of distance over 15
meters, it is recommended to use Ethernet connection.RS485
cable can be used for connection when distance exceeds 80
meters and can connect for 1000 meters maximally.

User management 
This step is mainly to register each fingerprint machine or upload
users. When there are many fingerprint records, it is recommended
to use ―U are U‖ Fingerprint Sensor to register users first. Then
upload users to each fingerprint machine respectively. In user
management, you can edit employee’s information, create
password for employee and set corresponding privilege.

Access control management 
For Access control, we define that all users are initialized as
invalid user. User can become valid user in effective time
period only after user is assigned privilege. So we need to
upload Access control setting after we finish uploading users
-6-
Access control software introduction
1. Installation and Uninstall
1.1 Installs software
Before installing your software, it is better to shutdown other
running application programs, in order to keep away conflict
in installing process.
Note: Maybe some displaying figure does not tally with
real contents please subject with CD you install
Please put the CD with software into CD-ROM, it will be
running automatically and pop-up following interface.
Select an installation Language, Click Next, enter follow interface
-7-
Access control software introduction
Click Next, enter follow interface:
This interface fully provide with three way the software apply to,
there use method ability to be shifted by the setting, this software
mainly apply to the access control, so select the a Access
-8-
Access control software introduction
Control Device as example, Choose Access Control Device .
Click Next, enter follow interface:
Please read this license Agreement carefully, if you agree to
the terms, select the I accept... button and click Next.
If you do not agree above terms, select I don’t accept…., the step
will exit the installing program and return, enter following interface
-9-
Access control software introduction
This interface applies to locate the folder of the fingerprint access
control software, you may use the default folder, also can create or
select a folder, and Click Next enters following interface:
After select installing component. Click Next, Enter following
- 10 -
Access control software introduction
interface
This window is to confirm the folder which is created in
Start/Program item. Click Next, display following Interface
- 11 -
Access control software introduction
After enter into this interface, it is show that you have finish all
configured to setup, if want to modify it, Click Back to return,
Otherwise click Install, the installing program will copy and write
corresponding information into hard disk, After finish installation,
click Finish to complete the process。
1.2 Uninstall software
If you will not use the software and want to delete it from the
computer, may perform following operation:
Exit from all PEGASUS software Access Control management
software, enter Start-> Setting-> Control Panel-> Adding/
Cancel to select PEGASUS software and click Cancel to delete
it, may be there are some files which is not to be all deleted, you
ability to entry the installing directory to cancel the folder of
Pegasus emnetman
In the Starting /Program to run the access control system, in this
portion of the Base Setup, you will review 6 module of the base
- 12 -
Access control software introduction
setup, Access Control, Base Operation, Query, Help. The
equipment must be added before using it.
- 13 -
Access control software introduction
2. Base Setup
In the portion of the Base Setup, include Department
Management, User Management, Equipment Management,
and Load from USB flash disk, System Setup and Exit
2.1 Equipment Management
First add equipment, open Equipment in the Base setup
menu, the display interface is following
Click Add button underside of the list, display interface is
following
2.1.1 Communication Setup
Communication Setup: Click Read Option; it can show
communication setup of all equipment to be connected. Like
as following figure
- 14 -
Access control software introduction
Communication type: Change to Serial Port/RS485
Machine num: Input number of fingerprint machine according
to the own requirement. For example, number of fingerprint
machine is set to 1, and its identify ID is set to Machine 1.
Communication Key: it is not required to set under default
condition. If communication password is set in fingerprint machine,
then it is required to enter communication password correctly.
Port Number: Select communication port number that connects
PC and fingerprint machine. Default value is COM1.
Baud Rate: Select 9600 (recommended)
Note: Above settings are used for RS485 connection. If RS232
connection is used, then Baud Rate should be changed to
115200, which will increase communication speed greatly.
Ethernet
(2)If the Ethernet communication mode is selected, shown
as following :
- 15 -
Access control software introduction
Name: Enter name according to the own requirement. For
example, name is set to Machine 1.
Communication key: it is not required to set under default
condition. If communication password is set in fingerprint machine,
then it is required to enter communication password correctly.
IP address: Default value is 192.168.1.201. IP address can be
changed according the network segment of local area network,
but IP address cannot conflict with other IP address of any
machine in the same local area network. Please notice that to fill
IP address of fingerprint machine should remain the same IP
address as that is edit in fingerprint machine.
Port: Default value is 4370 (no change)
There are two connection modes that have been described above.
You can select different modes to connect devices as requirement
by yourself. After finishing setting, click Test Connection button on
the bottom to test connection . After Connection Success
appears, click Save button to save the setting of this fingerprint
machine. If Connection Failure, please check the setting both
fingerprint machine and communication setting. You can use the
- 16 -
Access control software introduction
same method to add next fingerprint machine to system.
After all fingerprint machines are added, an icon of fingerprint
machine that has been added will appear in List on the left of
Device Manager. If you want to edit the information of fingerprint
machine, ability to read the setup of fingerprint machine firstly, then
you can directly modify it, click Apply Setup button below to
complete modifying. If you want to delete one fingerprint machine,
select the fingerprint machine and click Delete button below.
Read Option
If you want to check connection information of one fingerprint
machine, click Read Option to get connection information of
that fingerprint machine.
2.1.2 Fingerprint Machine Information
Click Fingerprint Machine info in the Equipment
Management item, display interface following.
- 17 -
Access control software introduction
Click Read Option, the base information of fingerprint
machine will be list. Like following Figure:
2.1.3 Wiegand
Click Wiegand in the Equipment Management, display
interface is following:
- 18 -
Access control software introduction
Click Read Option to obtain all kinds of wiegand parameter
which store in the fingerprint machine; there are four Defined
Formats in the drag –down volume to select. to choose a
wiegand 26 or 44444444444444444wiegand 34 is avaliable.
Defined Format: this format has been defined and built in the
system; User doesn’t need to define the length of Bit and the
location of information. There are four default defined format:
wiegand26 with device ID、wiegand34 with device ID、wiegand26
without device ID、wiegand34 without device ID. The wiegand 26
with device ID means that the W26 output format along with
equipment ID and the wiegand26 without device ID point that the
W26 output format doesn’t own the unit ID, Here the equipment ID
is defined by following condition: if there is no set of the site code,
then it will output machine code. And if the site code has been set,
it will output the defined site code (which is similar the machine
code, there different is that this code is defined by user and can
recycle to use, range is 0-255)
Fail ID: Export Fail ID after verified is failure, if it has been
selected; its output range is 0-65534.
Site Code: similar the machine code, which different is that this
- 19 -
Access control software introduction
code is defined by user and it can be recycled in different
unit, range is 0-255)
Self-define Format: User define Wiegand output format by herself
Total Bit: the length of output format
ID begin: The start location of the ID code in the total bit
ID Bit: The length of ID code
Pulse Width: the default value of to send pulse width time is
100µs, if the controller isn’t able to receive the Weigand
signal, can adjust value from 20 to 800
Pulse Interval: the default value is 900 µs, ability to adjust it
from 200 to 20000.
2.1.4 Verification
Click Verification in the Equipment item to read setting,
following interface display
1: N Match Threshold: A predefined number, often controlled by a
- 20 -
Access control software introduction
biometric system administrator, which establishes the degree of
correlation necessary for a comparison to be deemed a match. If the
score resulting from template comparison exceeds the threshold, the
templates are a match (though the templates themselves are not
identical).the default value is high, you can modify it
1:1 Match Threshold: It mean that match fingerprint
threshold after presenting the Card, the default value is high.
Only Verification No. Card: It is mainly designed for ID
card, if the item is choused as Yes, a user directly use ID
card to verify enough, to verify procedure doesn’t need to
press fingerprint. If the item is choused as NO, you must
verify fingerprint after present the card until pass
Only 1:1 Match: This feature is only available to that an user own
fingerprint, ID card or Mifare card for verification, can configure
Only 1:1 Match, if the item is choused as Yes to this setup, to
verify must first present a card, and then press fingerprint. If doesn’t
slide a card, there is no response to fingerprint in the unit.
Must Register Mifare Card: there are two statuses to register a
Mifare card, if the card was configured to Must Register, it is
only to verify the user who’s ID has stored in the fingerprint
machine. The user No. to be store will not be verifying.
When you choose the item as NO, no matter there are user’s
ID information in the unit or not, it will export as the user and
fingerprint template which is store in the card are verified
successfully.
You can change the option according you actual statue to
achieve the best result.
2.1.5 Power Management
Click Power Management to read setup. The following is
display interface:
- 21 -
Access control software introduction
Firstly read the parameter of Power Management, modify the state
of Idle Setup and minutes of Idle Time, then click the Application
Option to complete set. When the idle time is 0, then the idle setup
function is invalid. When the value more than 0, the machine will
enter into idle state after arrives at define time.
2.1.6 Access Control
Click Access Control to obtain Setup, display interface as follow:
- 22 -
Access control software introduction
Delay time of lock control apply to determine unlock hour, the min
measured unit is20ms, in the normal condition is 100—200ms.
2.1.7 Mifare Card
Click Mifare , display follow interface:
Fingerprint Amount: How many fingerprints are stored up in the
- 23 -
Access control software introduction
Mifare card
Fingerprint First Sector: the first sector of Mifare card to
store fingerprint
Fingerprint Total Sector: fingerprint hold total sector.
Password of card: Read and write password of card, you
only can set it, can’t obtain it.
2.1.8 Other Setup
Click Other Setup the following appear:
This module provide with mainly convenience to configure
equipment.
Restart Unit: in the list, select a device and Click the name
of the device to restart fingerprint machine.
Clear Administer Privilege: this function can clear all administer
privilege which has registered in the fingerprint machine. Firstly
choose the name of the device from the list, then to do it
- 24 -
Access control software introduction
Upgrade Firmware: We remind that user doesn’t use the
function random, except user receive the manufactory notice,
according to the guide which factory offer to do.
Initialize Equipment: This function is mainly used to clear all
data in the reader.
Seize Fingerprint Image: This function can be used to view
fingerprint image, if want to inspect fingerprint image, please
place finger on the sensor window, don't move, and then
click the button, and will see the fingerprint
Date formats: Select the date formats from drag- drown box, this
data formats appear on the starting interface of fingerprint machine.
Voice function: Utilize this function to determine the prompt
voice of the fingerprint device on or off.
2.2 Department Management
Click Department Management in the Base Setup menu,
pop –up the Department Management main interface, like
as following figure.
- 25 -
Access control software introduction
Click
department,
or
to add or delete a interrelated
is to Enroll Department Staff Button.
After established a new department, if want to shift a staff to
anther department, first select the head-office, then click
Enrolling Department Staff button, pop-up following interface.
- 26 -
Access control software introduction
Select the staff of corresponding department and add it to column, click
enroll staff button.
2.3 User Management
User management provides maintenance work for staff
information. Click User Management from drag-down menu
of Basic Setting, and main window of department
management will pop up as follows::
- 27 -
Access control software introduction
(1) User list Sort Order: Click the name of field. Choose a
triangle symbol which is beside the field, according to
ascending order to arrange when the triangle symbol point
upwards, otherwise, the triangle symbol point downwards that
means the sort order follow the descending order, you can
click triangle symbol to change the rise or down rank.
Statistic: the software can automatically count the total
record and also can count grouping record.
Left side is a user list and right side is a user maintenance setting
area. If one staff is redeployed from a headquarter to other
department, click corresponding the department from down drag
buttons of Department, a dialog will appear and ask whether the
staff is redeployed to this department or not. Here, you can set
user’s privilege. If you want to change one user to other identity, for
example an administrator, first select this user in list on the left and
then select Administrator from down drag options of Privilege on
the right. If you want to add password to one user, first select this
user in list on the left and then click Set Password to add
password. After this user is uploaded to fingerprint machine,
- 28 -
Access control software introduction
one user number will be added in password registration.
Therefore, this user can not only use fingerprint, but also use
password when identifying.
(2) Enroll fingerprint State: this item will show every user
enrolling State:
(3)Import: This function can realize to import data, this
importing software support all kinds of format user’s data file.
This system support following format data to import
MS Excel、MS Access、DBF、XML、Text File、CSV
file,we recommend use the CSV file to import, the following
example which take CSV file to import user’s data is used to
illustrate how to import data.
(1)、First click the radio button of CSV file, then select the
file that want to be import.
(2)、Click Next, the following figure appear
- 29 -
Access control software introduction
The left side list is a field list, the right side is a import file rank,
there are Skip line(s) on the right-up part, that means want to skip
amount of the line, if the first line to be import isn’t material data,
you can fill 1 here, that show to skip the first line to import data.
Fields List Explain:
UserID: The ID only is used in the system interior, it is
useless to import the fields, please don’t use the field
BadgeNumber:User code, this code is that user adopts the
number in the fingerprint machine and the software.
Name: User name, these fields must exist.
VerificationMethod:User’s verification method. This item
can be neglected.
DefaultDeptID:Department ID. If you wan to import the
data from other origin, this item can be neglected.
Gender: Males or Females
Title:Title
- 30 -
Access control software introduction
Photo: Photo can be neglected
Privilege:Privilege can be neglected.
Password: Password can be neglected.
CardNo:ID card number can be neglected.
(3)、First choose the field in the Fields list as to import, then
select the corresponding rank in the right side list. The Fields
list will automatically attach the corresponding number to the
name of field, such as it is, arrange all fields and
corresponding rank after to complete, click next.
If you want to cancel a field’s setup, first choose the field, and then
click corresponding rank, the software will cancel this field’s setup.
(4)、Click Execute button to run input operation.
Export:This function can realize that the software export
user’s data via all kinds of format which can be support by the
software. In order to it is convenient to supply third party to use.
Following, take the exporting MS Excel file as an example
to explain:
Click the Export button, appear following interface
1. Select the object file which is to be exported
- 31 -
Access control software introduction
2、Click Start Export button to export the file via default
format, otherwise, can configure exporting content through to
click the different option card.
Fields:Select the field to be export, the default format is all,
it is only to export field’s content after selected field.
Formats:Be exporting format of defined all kinds of field value.
Header & Footer: The file is starting and ending of the text.
Caption & Width:The title and width of field
Excel Options: Set font
Transfer User’s Information and Fingerprint
(5) Photo: There are two ways to attach photo, one way is
directly import photo into the file, and other way is to utilize a
- 32 -
Access control software introduction
camera to seizing image.
(6) Fingerprint Management
Enroll Fingerprint by The Fingerprint Sensor:
To use U.are.U sensor can enroll user's fingerprint under the
connecting condition, click shortcut ―+” button to add new user
in the staff maintenance item, choose fingerprint sensor to enroll
fingerprint after finishing the enrollment procedure and close
enrolling interface, the system will store the user’s fingerprint
into the local Database, the new user’s info can be send to the
fingerprint machine via From PC to Fingerprint machine. The
enrollment interface like as following figure illustration.:
Select the finger which want to be enrolled to enroll; if want
to delete this fingerprint, please double click this finger.
- 33 -
Access control software introduction
Select a user you want cancel, Click shortcut ―-” button to
delete the user.
Enroll Fingerprint by The Fingerprint Machine: Use the
fingerprint machine to enroll. Select the fingerprint machine
on the blank area, Click Connect Enrollment Equipment to
connect fingerprint machine, after to connect successfully,
the disconnection will appear, click Enroll to begin
registration fingerprint.
Note: this function only is used for black-write LCD
fingerprint machine, Now the TFT Screen Fingerprint does
not support this function.
Enroll Mifare Card: Choose the user who wants to register the
Maifare Card, then click Through Fingerprint Machine to
Write Card, the software will remind Punch Card, to slide the
card near an appropriate place in the fingerprint machine, after
to show Write Card successfully on the unit, this user's code
and the fingerprint will store in the card. Click Through
Fingerprint Machine to Clear Card to delete user's data in the
Mifare, the program remind Present Card, to slid the card near
an appropriate place in the fingerprint Machine, after to notice
Clear Card successfully to show the operation well.
Note: this feature is available only to the fingerprint machine
which support the Mifare card enrollment
Fingerprint Register Status: to show the detail of user and
fingerprint register
Sort Order: can arrange the record according to the
ascending or descending order in the record list, directly click
the head of rank to achieve, following figure is the process of
sort order which according to the name.
(6) Transfer
User’s Information and Fingerprint
Form PC to Fingerprint Machine: the user which is store in
the database will be uploaded to the fingerprint machine,
click From PC to fingerprint machine, pop –up the
interface to upload user’s fingerprint.
- 34 -
Access control software introduction
Upload:Base on your need, Select a staff and an
uploading fingerprint machine, click Upload, it is able to
upload user’s data to the defined fingerprint machine.
Notice:User’s data include user information and fingerprint.
Delete: If you want to delete a user in a fingerprint
machine, first choose user and corresponding fingerprint
machine, and then click Cancel button.
Operation Log:That is an error log during operating process
Batch:Utilize the function to speed up communication when
there a lot of users are need to be uploaded, if there a few
user, do not use it. (E.g... 30user)
From Fingerprint machine to PC: The user which is store in the
fingerprint machine will be downloaded to the local database, click
From fingerprint machine to PC, pop –up the interface to
download user’s data.
- 35 -
Access control software introduction
Select a fingerprint machine No. to download user’s
information which is on the left side list, click View User in
the Fingerprint machine, it is able to display all user in the
fingerprint machine, Select a user to be downloaded, click
the ―Download‖ button to download the user information and
fingerprint from fingerprint machine to local database
View User in the Fingerprint machine:Display all users in
the fingerprint machine
Download:Download user data to be selected.
Delete: If you want to delete a user in a fingerprint
machine, first choose user, and then click ―click‖ button.
Batch:Utilize the function to speed up communication when there
are a lot of users to be Downloaded, it isn’t need to a few user.
Note: this function only apply to Black–white LCD serial fingerprint
machine, the TFT screen serial fingerprint machine do not support this
- 36 -
Access control software introduction
function.
Operation Log:that is a error log during operating process。
Note:In the process of the user management, if the
fingerprint and user will be upload or download, the
monitor function should be shut down firstly, if want to
upload,the download operation will be priors, the
operation must enter user management once again.
2.4. Load from the USB flash disk
Load the attendance data of USB flash disk to the software
through this item, like as following figure:
Load in : On the left side list choose the data you want
load in. click Load in to load data to system.
- 37 -
Access control software introduction
Delete Data:On the left side list choose the data you want
delete. Click Cancel to delete the data from system
2.5 Management USB Flash Disk
The Option can be used to download the attendance data,
and download and upload employee data through USB flash
disk. This operation is as following
2.5.1 Load in the User Data
Click USB Flash Disk Management in the Base Setup, and enter
the U flash disk management interface. Like as follow figure.
Click Load the User Data from the USB disk button. The
system will automatically search the user data and load it into
the system from the USB flash disk, if a new use is found, the
system will prompt whether add the new user to system or not.
In the list the records with red color show this record do not
- 38 -
Access control software introduction
synchronization with data of software, click override to cover
asynchrony data up by the data of computer.
Delete Data of U Flash disk: Delete user data of user data
of U flash disk
Clear List: clear list on left side
2.5.2 Export user data
Click label of exporting data, display as follow
Left side is a department list. Ability to choose a department
from the list, all staff information will be appear on the
information list, Double click staff record or selected staff and
click move the selected record to right side add an
employee information in the right side. If there are a lot of
staff record, ability to show all staff information of the staff to
be queried through staff information query function.
Maintained Staff Information
- 39 -
Access control software introduction
Add: Add a piece of information of staff.
Modify: modify selected staff’s information
Delete: delete selected staff’s information.
Click export user data to U flash diskette. Then all record
accessories in the ready exporting to U flash to data list will
be exported to U flash disk
2.6 System Setup
System Setting of Access control software mainly includes following
several parts. First open System Setting, as shown in figure below:
- 40 -
Access control software introduction
2.6.1 Automatic monitoring
Run automatic monitoring when program start-up
If this option is selected, program start-up will enable automatic
poll all devices that has been connected with. If this option is not
selected, program start-up will not enable poll.
Default device rotation periodicity
During device continue poll, some fingerprint machines may
disconnect temporarily due to various reasons. Here, you
can modify device rotation periodicity in second (it is
recommended to set to 120)
Remain device record
Device record number means user attendance records that are
downloaded in every device. You can enter a record number. If actual
record number exceeds the pre-set value, the software will clear all
fingerprint records stored in fingerprint machine. For example, record
number to store is set to 1200, when record number downloaded is
1201, all fingerprint records in fingerprint machine will be deleted and
record number downloaded resets to 0.
Count for continuous failure retries
Count for continuous failure retry (it is recommended to set to 3)
that is convenience to reconnect automatically under the
condition of fingerprint machine recovers normal connection.。
Run monitoring in specified Period time
Here, we can define one time period to run monitoring. If run
uninterrupted polling, it will bring huge burthen to whole
monitoring network. You can define one time period to run
monitoring, in order to reduce burthen of monitoring network.
Please pay attention to time format, such as 06:00-22:00.
Download all record cycle: Set the cycle to download record
automatically.
Synchronize time of fingerprint machines:
- 41 -
Access control software introduction
You can define a time to synchronize time of all fingerprint
machines that have been added into device. Please pay
attention to time format, such as 10:00
2.6.2 Parameter of Server
Select start to connect with network function; it is need to
input the IP address and port of linked Server.
2.6.3 Function Configuration
Select the function you want, the three function can be
shifted before use the function you have to restart the device.
Unit Name:Enter company name here.
Set database connection: For more detail see Set
Database Connection,
Run the program when windows start-up If this option is
selected, then the program will run automatically every time
after PC start-up. If this option is not selected, then this program
will not run automatically every time while PC start-up
- 42 -
Access control software introduction
3. Access Control Setup
Access control setting is to set unlock time and assign privilege
for registered users. Settings of each user consist of three
period time settings and one group setting. Relationship
between period time and period time is ―OR‖. Group also
consists of three period time settings and by the same token,
relationship between these three period time is ―OR‖.
Simply put, if you want to keep a registered user in unlock status.
Firstly the group that this user is in should be defined in unlock
combination (one group can be defined in one combination together
with other group, but these groups are required to unlock door
together). Second, current unlock time is in any availability range of
user time period and period time of its group.
Under system default, a new registered user is in Group 1
and group combination is Group 1. So new registered user is
in unlock status under default. If a group that user is in is not
defined in group unlock combination setting, then the use
can only record attendance and cannot unlock door.
3.1 Period Time
Time period is the smallest time period unit in Access control
setting. In whole system, you can define up to 50 time periods.
Each time period defines 7 time intervals, i.e. one week. Each
time interval is valid time period in 24 hours everyday. Each use
can set up to three time periods and the relationship between
these three time periods is ―Or‖, which means the user is valid
as long as identification time satisfied one of these three time
periods. Each time period format of time period is HH: MM-HH:
MM, i.e. in term of 24 hours format and precision to second.
End time less than start time (23:57-23:56) means all day forbidden.
End time larger than start time (00:00-23:59) means valid in the
- 43 -
Access control software introduction
time interval.
Valid time period for user unlocks: all day open (00:00-23:59)
or time period with end time larger than start time.
Click Time period from Drag-down menu of Access Control
Setting, window of adding Time period will pop up. Click Add
button and system will pop up a timetable from Sunday to
Saturday. Here, you can define any time period you may use.
Then click Confirm to save the time period automatically. If you
want to use several time periods, continue to click Add. In
addition, time period can be edited and deleted.
3.2 Group
Group function can divide users into groups and combine different
- 44 -
Access control software introduction
groups to different unlock combinations, which make group
management of Access control more convenience. So user
can define many unlock combinations. System has defined 5
groups: Group 1, Group 2, Group 3, Group 4, and Group 5.
Under system default, new registered user is in Group 1 and
can be re-assigned to other group.
Under system default, a new registered user uses time period of
Group 1. After the user is re-assigned to other group, the user
uses default time period of the corresponding group. So please
make sure to define default time periods for each group.
Group Setting
Entered the "group" setting ,there are two ways to enter:
1) Through bar options of the system menu: Access Control
Settings -> Group, set up group access interface.
2) Through shortcuts button options of the system : Time
Period, Enter the group setting interface.
Enter the "group setting" interface, shown as following figure.
Group editing. left click item that need to edit with cursor to enter
the editing state.
- 45 -
Access control software introduction
Through drop-down box to choose the Time Period .
Through the drop-down box to choose verification way
If you want to holiday Time Period take effective, selected it by
cursor clicks, if you want the holidays is invalid, it can not selected.
- 46 -
Access control software introduction
Set up is completed, click on "Save" to save
3.3 Unlock Combination
Definition of unlock combination function
Unlock combination is the direct expression for controlling
unlock. For example, if you want that all registered users
cannot unlock door, then set Unlock Combination to null.
Definition of unlock combination is defined to different
combinations that can unlock door, and each combination
consists of different groups. Unlock combination directly uses
group number and does not consider order for identifying
user between each group. For example, ―123‖ means door
will only be unlocked when at least one user in each group of
Group 1, Group 2 and Group 3 passes identification together
with other two users. ―4‖ means door will be unlocked when
one user in Group 4 passes identification together with other
two users. System can define up to 10 unlock combinations
at the same time and door will be unlocked as long as one of
these 10 unlock combinations passes identification.
- 47 -
Access control software introduction
3.4 User Privileges
User privilege mainly applies to user access control setting: if
a user whose personal No. is assigned as 1,2,3,4, and is
distributed to No. (1) Device in the default period time, likes
as follow, add user to right list first, then add device to right
side list. Click allows passing.
1 entered the "Access Control Privilege‖ setting there are two
ways to provided:
1) through the system menu bar options: Access Control Settings ->
Access Control Privilege, enter Access Control Privilege interface.
2) through directly shortcuts button of the system : Access
Control Privilege, enter Access Control Privilege interface.
- 48 -
Access control software introduction
2 enter the "Access Control privilege" interface such as shown.
3Click on "Edit Privilege" button and enter the Access
Control Privilege to edit the interface, shown such following.
4 default users belong to Group 1, if need be assigned to other user
groups, the need for users to re-allocation group. Here we illustrate:
- 49 -
Access control software introduction
No. 1 users assigned to Group 1.
First selected No. 1 users, shown as following.
5 Click on the "Set Group" button and enter "the group
setting" interface, select group 2.
6 through the above steps, the users will be assigned to the
second group, shown as following.
- 50 -
Access control software introduction
7 follow the 4-6 steps, set up the group those users respective.
After the setting completed, through ">/>>" button, a single or all
of users will be moved to the right critical areas, waiting for the
Privilege setting. Shown as following
8 in the equipment list choose the equipment that need to
upload Privilege.
- 51 -
Access control software introduction
9 through ">/>>" button, single or all of the equipment will be
moved to the right the critical region, waiting for Privilege
setting. Like following equipment known as the NEW UNIT_1
, the equipment has been moved to the critical region,
waiting for Privilege setting
10 after users and equipment is selected, click on "allows"
button, the group Time period which is used by user in the
critical periods will be assigned to the selected devices. After
distribution is successful, prompt will appear shown as following
- 52 -
Access control software introduction
11 In the "User Access Control Privilege" interface, click
"exit" button and enter the "Access Control Privilege Setting"
and synchronize set up information of user groups will
display in the list. Shown as following, NEW UNIT_1 in the
No. 1 user group 1 Time Period.
2) Set up the Access Control Privilege When a user do not
use group
1 if a user belongs to the group, but she/he does not use group
Time Period, then in the "User Access Control Privilege" setting
interface, select the Time Period to be used, shows as below,
No. 10 users belong to the third group, but he/she does not use
group Time Period, and use the 1,2,3 Time Period
- 53 -
Access control software introduction
2 After completing, in the "user Access Control Privilege" interface,
click "exit" button and enter the "Access Control Privilege Setting"
and synchronize set information of user groups will display in the
list. shown as following, in the NEW UNIT_1 the No. 1 user use the
2 group Time Period. in the NEW UNIT_1 the No. 10 user use group
3 Time Period, the non-use group, but use 1,2,3 Time Period
3) Delete the user Access Control Privilege
- 54 -
Access control software introduction
1 After choose the user who will ready to be deleted and his
group , move their to the critical areas, and moved
equipment whose the Privilege will be deleted to the critical,
shown as below, delete the No. 1 users in NEW UNIT_1 ,
who use the Group 2 Time Period .
2 Click on the "AccessDeny " button, the group Time
Period the user use will be deleted in critical area from the
selected equipment. After deleted successfully, the system
will prompt shown as in the dialog box.
3 after completion, in the "User Access Control Privilege"
interface click "exit" button and enter the "Access Control
Privilege Setting" , and synchronize the set information of
user groups will display in the list. shown as following , only in
the NEW UNIT_1 the No. 10 user use group 3 Time Period,
Do not use group, but use 1,2,3 Time Period
- 55 -
Access control software introduction
After assigned the privilege, ability to automatically produce a
privilege table, click exit to exit, the following figure will appear
- 56 -
Access control software introduction
4 through shortcuts delete user privileges. in the Access
Control Privilege setting interface, select the user to be
removed , and then right click this item, the pop-up "delete"
button. Click this button to delete users.
3.5Holidays setting
These steps is shown
1 entered the holidays set. Choose Access Control Settings > holidays set. Shown as following.
2 Click on the "New" button, can add a holiday. The default
date is the date you choose.
- 57 -
Access control software introduction
3 move the cursor to the "start date", it is start date to revise
holiday,
4 move cursor to the "end date", it is end date to revise holiday .
- 58 -
Access control software introduction
5 moved the cursor to the Time Period to be set, choose the
valid Access Control Time Period .
- 59 -
Access control software introduction
6 set is completed, click on the "Save" button, the setting will
be saved.
After complete assigned the user privilege, next step is to
upload the user access control setup and the basic access
control setup to fingerprint machine, exit to the main program
interface, may see upload setup, must upload the privilege to
N machine prior selecting N machine, if want to upload many
fingerprint, may hold down Ctrl to select and click Upload
setting again, a dialog box will pop-up, As counting the need to
click confirm to upload Access Control Setup.
Note: when the privilege is assigned to user, because all the
group period time of users is defaulted as 1 group, therefore
there are two kinds of situations occurring:
1st, user use group time period, designated a user in the left
side user list (may hold down the Ctrl key to select), then
click redistribute the group in the user privilege assign
which the group is designated user .
2nd, user does not use the group time period and directly uses the
time period, add a user to privilege distribution list in the right side ,
from three time period option in the top right corner the time period
- 60 -
Access control software introduction
is choused in the user privilege distribution list which can use
- 61 -
Access control software introduction
4. Base Operation
The base operation fully provide with three sub-module—
Upload Setting, Open Door, Starting/Stopping Monitoring。
4.1 Upload Setting
Choose operation device , click Upload Device, show as
following interface :
Select the Access control setting which you want, the two
kind of setting ability to be choused at same time
4.2 Upload Equipment
Choose upload equipment. click icons to choose the
equipment with mouse, selected this equipment.
- 62 -
Access control software introduction
Select "upload set up" interface, there are two ways to enter:
1) through bar options of the system menu: basic operation > upload settings, enter upload interface.
2) through the system shortcuts button options: upload
settings, enter upload interface.
There are two choices to upload interface elements, the basic
setup and user Access Control Access Control setting, and it is
better the two selected together at the same time to upload.
This can choose to upload multiple machines.
- 63 -
Access control software introduction
Upload success, in its lower right corner the successful
operation prompt will be displayed, shown as below
- 64 -
Access control software introduction
4.2 Open Door
Click Open Door to open the selected door remotely.
4.3 Starting/Stopping Monitoring
The monitoring function already run after the program is
running, the information about opening door and fingerprint
verification will not show on the list
- 65 -
Access control software introduction
5. Query
These modules include record and alarm record
5.1 Record Query
In Start/End Date, you can select time period to query, Click
Query, list below will show all users’ come-in and go-out records
within the time period. Each rank in the table has drag-down
condition for searching. If you want to do classify Query, you can
drag head of rank to table head of query table, show as following.
Click Output to output fingerprint records in various formats,
such as Excel format, etc. this operation like as user
management exporting operation.
- 66 -
Access control software introduction
5.2 Alarm Record
Click alarm record. The following interface appears.
When the fingerprint identify fail or the Duress fingerprint has
been verified the alarm record will produce.
- 67 -
Access control software introduction
6. System Management
System Management includes that Operator Management,
System Operation Log, Backup Database, Clear old Data,
Initialize System and Set Password of Database. Eight
sub-modules
6.1 Operator Management
Click Operator Management in the System Management menu,
Pop-up the main interface of administers maintained, like as follow.
Click Administer,Pop-up the two item of Add Administer
and Cancel Administer, and then pop-up a user list frame,
Select a user to be add a administer, and the click Confirm
to pop-up a distributing privilege list. Like as follow
- 68 -
Access control software introduction
Put a tick in front of the administer privilege, and then click
Confirm.
If want to cancel administer, click Administer firstly, and then
click Cancel Administer to complete the operation process.
It is able to modify administer password and operation
privilege after a administer is added
In the administer interface, Choose a administer and click
modify, then follow the system prompt to click privilege to
reset its privilege.
If there is only one administer in the system, a administer
want to be canceled, you firstly find the Database Att2000,
and open the list of Userinfo, delete the field Securityflags
6.2 System Operation Log
The system operation Log is a track record which records this
software operation history, and utilize list mode to record all
- 69 -
Access control software introduction
operation. Click Cancel, this operation is availed to delete operation
log to the defined previous date, appear following figure.
6.3 Data Maintenance
The Data maintenance is, consist up Backup Database, ,
Compress Database, Clear Old Data, threes module Buildup
6.3.1 Backup Database
Click Backup Database in the System Management menu, pop-up
a dialog-box to backup database, you can name it as your favor,
and save it in the defined location, like as following picture:
- 70 -
Access control software introduction
6.3.2 Database Compress
Click Database Compress in the Data Maintenance menu, to
compress database, it is only capable to Access Database.
6.3.3 Clear Old Data
Can use the function to clear old data which are useless to
utility, click Clear Old Data in the Data Maintenance display
interface as follow
- 71 -
Access control software introduction
Click the Menu to choose the date, and than Confirm to
clear old data at once, then old record data will backup in the
installation directory automatically.
Note:The delete content doesn’t include the ending date
be selected. You can choose the operation to backup
record data which is before the close data to your folder.
6.4 Initialize System
Click Initialize System in the System Management menu,
pop-up a warn dialogs box, like as following figure , executes
the command all the system will be initialized, after this
operation the all data will be clear.
- 72 -
Access control software introduction
6.5 Set Database
Click set database
1.Connecting Microsoft Access Database setup
(1)Provide program to select Microsoft Jet 4.0 OLE DB
Provider;
(2)Click ―Next‖ or ― Connect‖ enter the following interface.
- 73 -
Access control software introduction
Click
button, Can select the database file, the default
name is att200.mdb, according to real condition to renew
setup of the database connection.
2.SQL Server Database Connecting Setup
First you should establish the empty database on the
database server. you can find a script file with the name of
sqlserver.sql in the directory of instating CD, the empty
database is established in the front of the searcher of SQL
Server, and then open the sqlserver.Sql script files, to run
database which is to create this software.
In the Provider Select Microsoft OLE DB Provider for SQL
Server, click ―next‖ or ―connect‖ to enter this following interface
- 74 -
Access control software introduction
Confirm the server name for storing this database, information
for logging on this serve, and the database name. After run test
connection successfully Click (OK) button to complete settings
6.6 Set Password of Database
In order to ensure the database security, we may give the
database to set a password, when the database is opened needs
to input the password to prevent other people destroy the data
Clicks setup database password in the system administration
menu, inputs your password to press the confirmation, please
keep firmly in mind the password which you set. Has to revise this
- 75 -
Access control software introduction
password, enter the set database password interface to
input the new password once more.
- 76 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement