ACCO Brands RDX 1970 Instruction manual

ACCO Brands RDX 1970 Instruction manual
RDS 2050
RDX 1750
RDS 2270
RDX 1970
Mercury
RSX 1530
RSS 1830
RSS 2230
G Instruction Manual
F Manuel d’utilisation
D Bedienungsanleitung
I Manuale d’istruzioni
O Gebruiksaanwijzing
E Manual de instrucciones
P Manual de Instruções
T Kullanım Kılavuzu
K Οδηγίες
c Brugsvejledning
FI Käyttöopas
o
NO Bruksanvisning
o
S Bruksanvisning
Q Instrukcja obsługi
CZ Návod k obsluze
o
H Használati útmutató
o Руководствo по
RUS
зкcплyатации
Specifications
Models
RSX1530
RSS1830
RSS2230
Sheet Capacity -
13 sheets
15 sheets
19 sheets
Duty Cycle -
4 min on / 30 min off
4 min on / 30 min off
4 min on / 30 min off
Duty Cycle -
2 min on / 10 min off
2 min on / 10 min off
2 min on / 10 min off
Duty Cycle -
2 min on / 20 min off
2 min on / 20 min off
2 min on / 20 min off
Volts / Hz
230-240V AC / 50Hz
230-240V AC / 50Hz
230-240V AC / 50Hz
Amperage
1.7A
1.2A
1.2A
m IMPORTANT: ONLY INSERT ONE CD OR ONE CREDIT CARD AT A TIME.
English
Français
Deutsch
Italiano
Nederlands
Español
Português
Türkçe
Ελληνικά
Dansk
Suomi
Norsk
Svenska
Polski
Česky
Magyar
Pyccкий
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
g
a
d
a
d
g
f
e
e
f
b
b
c
c
Models: RSX1530, RSS1830, RSS2230
1
Illuminated Panel
2
Models: RDS2050, RDX1750, RDS2270, RDX1970
3
4
5
6
7
Lights and Icons Explained
Illumination
Colour of LED
Green
Red
Power on button pushed / no fault
Door open
Bin full
Motor overheat
Auto button pushed / shredding
light
Anti-jam at Measure mode
light
Anti-jam at Running mode
light
Forward jammed
light
Reverse jammed
light
Reverse button pushed
light
Auto mode
light
1
Power on
Amber
light
light
light
light
light
light
light
light
light
light
light
2
Happy face
Green
light
light
3
Sad face
Red
light
light
light
light
light
light
light
4
Anti-
jam
Red
flash
flash
5
Door open
Red
flash
6
Cool
down
Amber
flash
7
Bin
full
Red
flash
Introduction
Thank you for choosing this shredder from Rexel. We are sure it will serve you well, but please take a little time to study these instructions to ensure you get the
best out of your machine.
a Indicator Panel
bRSX1530, RSS1830, RSS2230: Pull Out Drawer
RDS2050, RDX1750, RDS2270, RDX1970: Door for Bin
c Wheels
d Power On Button
e Auto Feed Button
f Reverse Button
g CD Guide
Safety First
m
Shredders are safe to use as long as you take a few safety precautions.
• Ensure the machine is plugged into an easily accessible power outlet, and
ensure the cable is not likely to trip up a passer by.
Power On (Amber Light)
Shredder OK (Green Light)
Shredder not OK (Red Light)
Anti Jam. Too many sheets (Red Light)
Door Open (Red Light)
Cool Down (Amber Light)
Bin Full (Red Light)
Mercury Anti-Jam Technology
Mercury Shredders will only shred stacks of paper that are within the
shredders sheet capacity. Eg. A shredder with a capacity between 20 and
22 sheets will not allow the shredding of more sheets than this.
• Unplug your shredder before moving it or when it is not in use for an
extended period of time.
Sensors in the paper feed area measure the thickness of paper about to
be shredded. The ability to shred or not is communicated through red and
green lighting. Green means that the stack of paper is within the shredders
sheet capacity and OK to shred. Red means that you have too much paper,
remove some sheets in order to shred.
• Do not operate with a damaged power supply cord or plug, after it
malfunctions, or after it has been damaged in any manner.
Given that you are unable to shred more sheets of paper than the shredder
is capable of shredding, paper jams are prevented.
• Do not overload electrical outlets beyond capacity as this can result in fire
or electrical shock.
This prevents time wasted through reversing paper and unblocking jams not
to mention the mess it can create.
• Any attempt to repair this unit by unqualified personnel will invalidate the
warranty. Please return to supplier.
• The socket-outlet should be installed near the equipment and shall be
easily accessible.
• Do not alter the attachment plug. The plug is configured for the
appropriate electrical supply.
• Do not use near water.
• Do not use aerosol dusters or cleaners.
• Do NOT Spray anything into the shredder.
Although this shredder has been designed to be child safe, it is not advised
to operate the machine near children.
1
2
3
4
5
6
7
Warranty
Models - RSX1530, RSS1830, RSS2230
This machine is guaranteed for 24 months from the date of purchase.
Please return the unit to your supplier. This does not affect your statutory
rights.
Models - RDS2050, RDX1750, RDS2270, RDX1970
This machine is guaranteed for 24 months for the full product with an extra
36 months on the cutting heads.
G
Operation
1 Connect shredder to mains supply
2Press the central power on button (d). This will switch the power on
and all the LED warning symbols on the indicator panel (a) will flash in
sequence. The shredder will now be in standby mode and the “Poweron” symbol on the indicator panel will be illuminated amber.
3To commence shredding, press the right hand auto feed button (e) this
will illuminate the feed area green and illuminate the symbol green.
This sets the shredder into auto mode and initiates the Mercury anti jam
mechanism. You are now able to shred.
4Insert paper to be shredded into the feed area. The Mercury anti jam
mechanism will sense the thickness of the paper being shredded.
If the paper thickness is within the shredders capacity the motor will
start and your documents will be shredded. Cutters will stop once the
shredding process is complete.
If the paper thickness is greater than the shredders sheet capacity the
area around the feed slot will turn from green to red and the motor will
not run. In this situation the Mercury Icon on the indicator panel will
flash red, the green will go off, instead the will be illuminated
red.
5If this happens, remove some of the sheets from the paper stack and
re-try until the feed area reverts back to green, the shredder will then
automatically start and allow the paper to be shredded.
If the shredder is left in auto mode for more than 10 minutes without
being used, the shredder will automatically turn back to standby mode
in order to save power.
Reverse Function
1Should you wish to reverse the shredding direction whilst shredding a
document, a reverse button (f) has been fitted for your convenience.
2By pressing the reverse button the shredding cutters will change
direction allowing the retrieval of the document being shredded. The
feed area will turn to red.
3The reverse function will only run whilst the button is being pressed.
When the reverse button has been released the shredder will revert to
stand by mode.
4To turn back to auto mode simply press the right hand auto feed button
again.
CD and Credit Card Shredding
The Mercury models can also shred CDs and credit cards.
1Pull up the orange CD guide (g) located in the centre of the feed area
and flip it into position over the shredder mouth.
2For credit card shredding, switch the shredder to auto mode and insert
the card into the centre slot.
3For CD shredding, extend the sides of the orange CD guide, switch the
shredder to auto mode and place the CD into the centre of the CD slot.
Only 1 CD can be shred at a time.
Rare Occasions of Jamming
In the unlikely event of the shredder jamming, use the reverse function to
unblock the shredder. (see Reverse function section)
Alternating between the reverse function and the forward run (Hold Auto
start for 2 seconds) will help unblock the feed area.
Once the jam is clear, press the right hand auto button once to revert back
to auto mode. You can now resume shredding as normal.
Bin Full
When the bin is full the shredder will not function and the bin full symbol
will illuminate and flash red, the green will switch off and the will
illuminate red.
When this happens you must empty the bin.
• Pull open the drawer to empty. (RSX1530, RSS1830, RSS2230 )
• Open the door to locate the bin (RDS2050, RDX1750, RDS2270
RDX1970)
Once the bin is empty, close the door/drawer and press the auto button to
resume shredding.
Door Open Safety Function
If the door is opened during shredding as a safety precaution the shredder
will instantly stop, and the door open symbol on the indicator panel will flash
red. The green will go off and the red flash will illuminate. To resume
shredding, shut the door and press the auto button.
Over Heating
If the shredder is used continuously for long periods of time the shredder
may overheat. If this occurs the egg timer symbol on the indicator panel will
flash amber, the green will go off and you will see the red .
When the shredder is ready to be used again the egg timer symbol will stop
flashing and the green will show once again. To resume shredding press
the auto button.
Shredder Waste Sacks
Rexel shredder waste sacks AS1000 (Code 40070) should be used with
models RDS2050, RDX1750, RDS2270, RDX1970. We recommend that no
waste sacks are to be used for the models RSX1530, RSS1830, RSS2230.
Service
G ACCO Service Division
N Sannum & Stang
I ACCO Italia Spa
Freepost 193, Hereward Rise, Halesowen, West Midlands, B62 8AN.
Tel: 0845 658 6600, Fax: 0870 4215576, www.acco.co.uk/service
CCO UK Sales International
A
Oxford Road, Aylesbury, HP21 8SZ.
Tel: 00 44 1296 397444, Fax: 00 44 1296 311000
Gladengveien 16 0661 Oslo.
Tel: +4722685940, Fax: +4722686730, e-mail: [email protected]
Via Nenni 13, Settimo Torinese (TO) Via Regio Parco 10B/bis.
Tel: 011 896 11 11, Fax: 011 896 11 12
F ACCO France
o ACCO-Rexel Ltd
O ACCO Benelux
Q ACCO Polska Sp. z o.o.
B ACCO Benelux (Technische Dienst)
S ACCO Nordic Region
D ACCO Deutschland
o Arnoldstrasse 5, 73614 Scorndorf, Germany.
H Tel: +49 - 7181/887-160, Fax: +49 - 7181/887-165
CZ XERTEC a.s.
o
FI Somen Huoltopalvelu oy
o
Service Aprés-Vente, 8 Rue du 19 Mars 1962, 21601 Longvic, Cedex BP7/ZI.
Tel: 0802 872 356, Fax: 03 80 68 60 49
Peppelkade 64, 3992AK Houten.
Tel: 030-6346060, Fax: 030-6346070, [email protected], www.accobenelux.nl
Peppelkade 64, 3992AK Houten, Nederland.
Tel: 02-4117416, Fax: 02-4140784, [email protected], www.accobenelux.be
IRE
Clonshaugh Business & Technology Park, Clonshaugh Dublin 17.
Tel: 01 816 4300, Fax: 01 816 4302
Al-Jerozolimskie 184, 02-486 Warszawa.
Tel: +42 22 570 18 01, Fax: +48 22 570 18 33
Kontor 1, i norden AB Kanalvägen 16 194 61 Upplands Väsby.
Tel: 08 444 5191, Fax: 08 444 5199
Kanaamouka 1 00360 Helsinki. Tel: 956 050 510, Fax: 956 050 500
RUS
U Továren 770/1b, 102 00, Praha 10.
Tel: +420 271 741 800, Fax: +420 271 743 143, www.xertec.cz
A ACCO Österreich
Sallmann Bürotechnik GmbH, Esshaverstrasse 16, 5020 Salzburg.
Tel: 0662 4345 160, Fax: 0662 4345 164, e-mail: [email protected]
S ACCO Schweiz
ABC Bürotechnik AG, Winkelbüel 4, 6043 Adligenswil.
Tel: 041 375 6060, Fax: 041 375 6061,
e-mail: [email protected]
E ACCO Iberia SL
P Isaac Peral 19, 28820 Coslada (Madrid). Tel: 91 669 9391, Fax: 91 672 07 11
g Oddi
Höfdabakka 3-7 IS-112 Reykjavik. Tel: 00354 515 5000, Fax: 00354 515 5101
T Eraysan
Ankara Cad N.129, Sirkeci, Istanbul.
Tel: 0090 212 6591686, Fax: 0090 212 5226992, [email protected]
o ACCO Australia Pty.
AUS
Level 2 Building B, 8 Lord Street, Botany. NSW. Australia 2019.
Tel: 2 9700 0180, Fax: 2 9700 0195
c Mailtech
Baldersbaekvej 8B 2635 Ishoj.
Tel: 045 43 73 37 37, Fax: 0045 43 73 73 37 07, e-mail: [email protected]
ACCO Brands Europe
Oxford House
Aylesbury HP21 8SZ
United Kingdom
www.accoeurope.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement