Cisco DS-X9224-96K9= - Switching Module - Switch Installation guide

Add to my manuals
50 Pages

advertisement

Cisco DS-X9224-96K9= - Switching Module - Switch Installation guide | Manualzz

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

Release Date: October 30, 2013

Part Number: OL-27554-07

This document describes the caveats and limitations for switches in the Cisco MDS 9000 Family. Use this document in conjunction with documents listed in the

“Related Documentation” section on page 46 .

Release notes are sometimes updated with new information on restrictions and caveats. Refer to the following website for the most recent version of the Cisco MDS 9000 Family Release Notes: http://www.cisco.com/en/US/products/ps5989/prod_release_notes_list.html

Table 1

shows the online change history for this document.

Table 1 Online History Change

Revision

A0

Date

October 30, 2013

Description

Created the release notes.

Contents

This document includes the following:

Introduction, page 2

Components Supported, page 2

MDS 9000 Chassis and Module Support, page 8

Software Download Process, page 12

Upgrading Your Cisco MDS NX-OS Software Image, page 15

Downgrading Your Cisco MDS SAN-OS Software Image, page 19

New Features in Cisco MDS NX-OS Release 5.2, page 24

Licensed Cisco NX-OS Software Packages, page 29

Deprecated Features, page 31

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Introduction

Limitations and Restrictions, page 31

Caveats, page 39

Related Documentation, page 46

Obtaining Documentation and Submitting a Service Request, page 49

Introduction

The Cisco MDS 9000 Family of Multilayer Directors and Fabric Switches provides industry-leading availability, scalability, security, and management, allowing you to deploy high performance storage-area networks with the lowest total cost of ownership. Layering a rich set of intelligent features onto a high-performance, protocol-agnostic switch fabric, the Cisco MDS 9000 Family addresses the stringent requirements of large data center storage environments: uncompromising high availability, security, scalability, ease of management, and seamless integration of new technologies.

Cisco MDS 9000 NX-OS software powers the award-winning Cisco MDS 9000 Series Multilayer

Switches. It is designed to create a strategic SAN platform with superior reliability, performance, scalability, and features. Formerly known as Cisco SAN-OS, Cisco MDS 9000 NX-OS software is fully interoperable with earlier Cisco SAN-OS versions and enhances hardware platform and module support.

Components Supported

Table 2 lists the NX-OS software part numbers and hardware components supported by the Cisco MDS

9000 Family.

Note For the latest information about supported transceivers, see the Cisco MDS 9000 Family Pluggable

Transceivers data sheet.

Table 2 Cisco MDS 9000 Family Supported Software and Hardware Components

Component Part Number

Software M95S2K9-5.2.8c

M92S2K9-5.2.8c

M91S3K9-5.2.8c

M91S2K9-5.2.8c

Description

MDS 9500 Supervisor/Fabric-2, NX-OS software

MDS 9200 Supervisor/Fabric-2, NX-OS software

MDS 9148 Supervisor/Fabric-3 NX-OS software

MDS 9100 Supervisor/Fabric-2, NX-OS software

Applicable Product

MDS 9500 Series only

MDS 9222i Switch only

MDS 9148 Switch

MDS 9134 Switch and

MDS 9124 Switch

2

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Components Supported

Table 2 Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

Component Part Number

Licenses M9500SSE184K9

M9222ISSE1K9

M9200SSE184K9

M95DMM184K9

M9222IDMMK9

M92DMM184K9

M95DMM184TSK9

M9222IDMMTSK9

M92DMM184TSK9

M92SSESSNK9

M95SSESSNK9

M92SMESSNK9

M95SMESSNK9

M92IOASSN

M95IOASSN

M92IOA184

M95IOA184

M9222IIOA

M92EXTSSNK9

M95EXTSSNK9

M9200XRC

M9500XRC

Description

Storage Services Enabler License for one MSM-18/4 module

Storage Services Enabler License

Data Mobility Manager License for one MSM-18/4 module

Data Mobility Manager for one MSM-18/4 module —

Time Limited to 180 days only

Applicable Product

MDS 9500 Series only

Storage Services Enabler License for one MSM-18/4 module

MDS 9222i Switch only

MDS 9200 Series only

Data Mobility Manager License for one MSM-18/4 module

MDS 9500 Series only

Data Mobility Manager License for Cisco MDS 9222i MDS 9222i Switch

MDS 9200 Series only

MDS 9500 Series only

Data Mobility Manager — Time Limited to 180 days only MDS 9222i Switch only

Data Mobility Manager for one MSM-18/4 module —

Time Limited to 180 days only

MDS 9200 Series only

MDS 9200 Series only Cisco Storage Services Enabler License for SSN-16

(1 engine)

Cisco Storage Services Enabler License for SSN-16

(1 engine)

MDS 9500 Series only

MDS 9200 Series only Cisco Storage Media Encryption License for SSN-16

(1 engine)

Cisco Storage Media Encryption License for SSN-16

(1 engine)

Cisco I/O Accelerator License for SSN-16 (1 engine)

Cisco I/O Accelerator License for SSN-16 (1 engine)

Cisco I/O Accelerator License for MSM-18/4

Cisco I/O Accelerator License for MSM-18/4

MDS 9500 Series only

MDS 9200 Series only

MDS 9500 Series only

MDS 9200 Series only

MDS 9500 Series only

Cisco I/O Accelerator License for Cisco MDS 9222i base switch

Cisco SAN Extension License for SSN-16 (1 engine)

MDS 9222i Switch only

MDS 9200 Series only

Cisco SAN Extension License for SSN-16 (1 engine)

Cisco XRC Acceleration

Cisco XRC Acceleration

MDS 9500 Series only

MDS 9200 Series only

MDS 9500 Series only

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

3

Components Supported

Table 2

Component Part Number

Chassis DS-C9513

Supervisor

Modules

Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

DS-C9509

DS-C9506

DS-C9222i-K9

DS-C9148-K9

DS-C9134-K9

DS-C9124-K9

DS-X9530-SF2-K9

DS-X9530-SF2A-K9

Description

Cisco MDS 9513 Multilayer Director (13-slot multilayer director with 2 slots for Supervisor-2 modules, with 11 slots available for switching modules — SFPs sold separately)

Applicable Product

MDS 9513 Switch

Cisco MDS 9509 Multilayer Director (9-slot multilayer director with 2 slots for Supervisor modules, with 7 slots available for switching modules — SFPs sold separately)

Cisco MDS 9506 Multilayer Director (6-slot multilayer director with 2 slots for Supervisor modules, with 4 slots available for switching modules — SFPs sold separately)

MDS 9509 Switch

MDS 9506 Switch

Cisco MDS 9222i Multilayer Fabric Switch (3-rack-unit

(3RU) semimodular multilayer fabric switch with 18

4-Gbps Fibre Channel ports, 4 Gigabit Ethernet ports, and a modular expansion slot for Cisco MDS 9000 Family

Switching and Services modules)

Cisco MDS 9148 48-Port Multilayer Fabric Switch (1RU fixed-configuration multilayer fabric switch with 48

8-Gbps Fibre Channel ports)

MDS 9222i Switch

MDS 9148 Switch

Cisco MDS 9134 34-Port Multilayer Fabric Switch (1RU fixed-configuration multilayer fabric switch with 32

4-Gbps and 2 10-Gbps Fibre Channel ports)

MDS 9134 Switch

Cisco MDS 9124 24-Port Multilayer Fabric Switch (1RU fixed-configuration multilayer fabric switch with 24

4-Gbps Fibre Channel ports)

MDS 9124 Switch

Cisco MDS 9500 Series Supervisor-2 Module

Cisco MDS 9500 Series Supervisor-2A Module

MDS 9500 Series

MDS 9500 Series

4

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Components Supported

Table 2

Component Part Number

Switching

Modules

DS-X9112

DS-X9124

Services

Modules

External crossbar module

Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

DS-X9148

DS-X9704

DS-X9224-96K9

DS-X9248-96K9

DS-X9248-48K9

DS-X9708-K9

DS-X9232-256K9

DS-X9248-256K9

DS-X9316-SSNK9

DS-X9304-18K9

DS-13SLT-FAB1

DS-13SLT-FAB2

DS-13SLT-FAB3

Description

Cisco MDS 9000 12-port 4-Gbps Fibre Channel

Switching Module with SFP LC connectors

Applicable Product

MDS 9500 Series

Cisco 24-port 4-Gbps Fibre Channel Switching Module with SFP LC connectors

MDS 9200 Series

MDS 9500 Series

MDS 9200 Series

MDS 9500 Series Cisco MDS 9000 48-port 4-Gbps Fibre Channel

Switching Module with SFP LC

Cisco MDS 9000 Family 4-Port 10-Gbps Fibre Channel

Switching Module with SFP LC

MdS 9200 Series

MDS 9500 Series

Cisco MDS 9000 24-Port 8-Gbps Fibre Channel

Switching Module with SFP and SFP+ LC connectors

Cisco MDS 9000 48-Port 8-Gbps Fibre Channel

Switching Module with SFP and SFP+ LC connectors

Cisco MDS 9000 4/44-Port Host-Optimized 8-Gbps Fibre

Channel Switching Module with SFP and SFP+ LC connectors

Cisco MDS 9000 8-port 10-Gbps Fibre Channel over

Ethernet (FCoE) Module

Cisco MDS 9000 32-port 8-Gbps Advanced Fibre

Channel Switching Module

MDS 9200 Series

MDS 9500 Series

MDS 9500 Series

MDS 9500 Series

MDS 9222i Switch

MDS 9500 Series

MDS 9500 Series

Cisco MDS 9000 48-port 8-Gbps Advanced Fibre

Channel Switching Module

MDS 9500 Series

Cisco MDS 9000 Family 16-Port Storage Services Node

(SSN-16) — 16 fixed 1-Gbps Ethernet ports, plus 4 service engines that support 16 Gigabit Ethernet IP storage services ports.

MDS 9500 Series

MDS 9222i Switch

Cisco MDS 9000 18/4-Port Multiservice Module

(MSM-18/4) — 18-port, 4-Gbps Fibre Channel plus

4-port Gigabit Ethernet IP services and switching module with SFP LC connectors

Cisco MDS 9513 Switching Fabric 1 Module

MDS 9500 Series

MDS 9200 Series

MDS 9513 Switch

Cisco MDS 9513 Switching Fabric 2 Module

Cisco MDS 9513 Switching Fabric 3 Module

MDS 9513 Switch

MDS 9513 Switch

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

5

Components Supported

Table 2 Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

Component Part Number

Optics SFP-10G-SR

SFP-10G-LR

SFP-H10GB-CU1M

SFP-H10GB-CU3M

SFP-H10GB-CU5M

SFP-H10GB-ACU7M

SFP-H10GB-ACU10M

Description

10GBASE-SR SFP+ Module

10GBASE-LR SFP+ Module

10GBASE-CU SFP+ cable 1 meter

10GBASE-CU SFP+ cable 3 meter

10GBASE-CU SFP+ cable 5 meter

10GBASE-CU SFP+ active copper cable 7 meter

10GBASE-CU SFP+ active copper cable 10 meter

Applicable Product

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

MDS 9500 Series,

8-port 10-Gbps FCoE

Module (DS-X9708-K9)

6

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Components Supported

Table 2

Component Part Number

LC-type fiber-optic

SFP

DS-FC10G-SW

Cisco

Coarse

Wavelength

- Division

Multiplexi ng

(CWDM)

Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

DS-FC10G-LW

DS-SFP-FC8G-ER

DS-SFP-FC8G-SW

DS-SFP-FC8G-LW

DS-SFP-FC4G-SW

DS-SFP-FC4G-MR

DS-SFP-FC4G-LW

DS-SFP-FCGE-SW

DS-SFP-FCGE-LW

DS-SFP-GE-T

DS-CWDM-xxxx

DS-CWDM4Gxxxx

Description

SFP+ optics (LC type) for 10-Gbps Fibre Channel for shortwave mode

Applicable Product

32-port 8-Gbps Advanced

Fibre Channel Module

(DS-X9232-256K9),

48-port 8-Gbps Advanced

Fibre Channel Module

(DS-X9248-256-K9)

SFP+ optics (LC type) for 10-Gbps Fibre Channel for longwave mode

32-port 8-Gbps Advanced

Fibre Channel Module

(DS-X9232-256K9),

48-port 8-Gbps Advanced

Fibre Channel Module

(DS-X9248-256-K9)

SFP+ optics (LC type) for 2-, 4-, or 8-Gbps Fibre Channel for extended reach (40 km reach)

MDS DS-X9200 Series switching modules,

MDS 9148

SFP+ optics (LC type) for 2-, 4-, or 8-Gbps Fibre Channel for shortwave mode

MDS DS-X9200 Series switching modules

SFP+ optics (LC type) for 2-, 4-, or 8-Gbps Fibre Channel for longwave mode; supports distances up to 10 km

MDS DS-X9200 Series switching modules

SFP optics (LC type) for 1-, 2-, or 4-Gbps Fibre Channel for shortwave mode

MDS 9124, MDS 9134,

MDS 9148, MDS 9222i,

DS-X9100, and DS-X9200

Series switching modules

SFP optics (LC type) for 1-, 2-, or 4-Gbps Fibre Channel for longwave mode; supports distances up to 4 km

MDS 9124, MDS 9134,

MDS 9222i, DS-X9100, and DS-X9200 Series switching modules

SFP optics (LC type) for 1-, 2-, or 4-Gbps Fibre Channel for longwave mode; supports distances up to 10 km

MDS 9124, MDS 9134,

MDS 9222i, DS-X9100, and DS-X9200 Series switching modules

MDS 9000 Series SFP optics (LC type) for 1-Gbps Ethernet and 1- or

2-Gbps Fibre Channel for shortwave mode; not supported for use in 4-Gbps-capable ports

SFP optics (LC type) for 1-Gbps Ethernet and 1- or

2-Gbps Fibre Channel for longwave mode; not supported for use in 4-Gbps-capable ports

MDS 9000 Series

SFP (RJ-45 connector) for Gigabit Ethernet over copper MDS 9000 Series

CWDM Gigabit Ethernet and 1- or 2-Gbps Fibre Channel

SFP LC type, where product number xxxx = 1470, 1490,

1510, 1530, 1550, 1570, 1590, or 1610 nm

CWDM 4-Gbps Fibre Channel SFP LC type, where product number xxxx = 1470, 1490, 1510, 1530, 1550,

1570, 1590, or 1610 nm

MDS 9000 Family

MDS 9000 Family

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

7

MDS 9000 Chassis and Module Support

Table 2 Cisco MDS 9000 Family Supported Software and Hardware Components (continued)

Component

Dense

Wavelength

- Division

Multiplexi ng

(DWDM)

Part Number

DWDM-X2-xx.xx

Description

DWDM X2 SC optics for 10-Gbps Fibre Channel connectivity to an existing Ethernet DWDM infrastructure, with 15xx.xx nm wavelength, where xx.xx

= 60.61, 59.79, 58.98, 58.17, 56.55, 55.75, 54.94, 54.13,

52.52, 51.72, 50.92, 50.12, 48.51, 47.72, 46.92, 46.12,

44.53, 43.73, 42.94, 42.14, 40.56, 39.77, 38.98, 38.19,

36.61, 35.82, 35.04, 34.25, 32.68, 31.90, 31.12, or 30.33

Applicable Product

MDS 9500 Series

MDS 9200 Series

MDS 9000 Family

SFP LC type, where product number xxxx = 3033, 3112,

3190, 3268, 3425, 3504, 3582, 3661, 3819, 3898, 3977,

4056, 4214, 4294, 4373, 4453, 4612, 4692, 4772, 4851,

5012, 5092, 5172, 5252, 5413, 5494, 5575, 5655, 5817,

5898, 5979, or 6061nm

Add/Drop

Multiplexer

(ADM)

DS-CWDMOADM4A 4-channel CWDM optical ADM (OADM) module (Cisco

CWDM 1470, 1490, 1510, or 1530 NM Add/Drop

Module)

MDS 9000 Family

DS-CWDMOADM4B 4-channel CWDM OADM module (Cisco CWDM 1550,

1570, 1590, or 1610 NM Add/Drop Module)

DS-CWDM-MUX8A ADM for 8 CWDM wavelengths

MDS 9000 Family

MDS 9000 Family

MDS 9000 Family CWDM

Multiplexer

Chassis

DS-CWDMCHASSIS 2-slot chassis for CWDM ADMs

Power

Supplies

DS-CAC-300W 300W AC power supply

DS-C24-300AC

DS-CAC-845W

300W AC power supply

845W AC power supply for Cisco MDS 9200 Series

MDS 9100 Series

MDS 9124 Switch

MDS9200 Series

DS-CAC-3000W

DS-CAC-2500W

DS-CDC-2500W

DS-CAC-6000W

3000W AC power supply for Cisco MDS 9509

2500W AC power supply

2500W DC power supply

6000W AC power supply for Cisco MDS 9513

CompactFl ash

DS-CAC-1900W 1900W AC power supply for Cisco MDS 9506

MEM-MDS-FLD512M External 512-MB CompactFlash memory for supervisor module

Standalone Fibre Channel-to-Ethernet adapter Port

Analyzer

Adapter

DS-PAA-2, DS-PAA

Smart Card

Reader

DS-SCR-K9 Storage Media Encryption (SME) Smart Card Reader

Smart Card DS-SC-K9 SME Smart Card

MDS 9509 Switch

MDS 9509 Switch

MDS 9509 Switch

MDS 9513 Switch

MDS 9506 Switch

MDS 9500 Series

MDS 9000 Family

MDS 9000 Family

MDS 9000 Family

MDS 9000 Chassis and Module Support

Table 3 lists the MDS hardware chassis supported by Cisco MDS NX-OS 5.x.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

8 OL-27554-07

MDS 9000 Chassis and Module Support

Table 3 Cisco MDS NX-OS 5.x Chassis Support Matrix

Switch

MDS 9513

MDS 9509

MDS 9506

MDS 9222i

MDS 9148

Cisco MDS 8-Gb Fabric Switch for HP c-Class Blade System

MDS 9134

MDS 9124

Cisco MDS 4-Gbps Fabric Switch for HP c-Class BladeSystem

Cisco MDS 4-Gbps Fabric Switch for IBM BladeCenter

NX-OS 5.x Support

Yes

Yes

Yes

Yes

Yes

Yes

Yes

1

Yes

1

Yes

1

Yes

1

1.

This switch supports Cisco MDS NX-OS Release 5.2(2) and later releases, but does not support Release 5.2(1).

Table 4

Module

DS-13SLT-FAB3

DS-13SLT-FAB2

DS-13SLT-FAB1

DS-X9708-K9

DS-X9232-256K9

DS-X9224-96K9

DS-X9248-96K9

DS-X9248-48K9

Table 4

lists the MDS hardware modules supported by Cisco MDS NX-OS 5.x. For the list of MDS hardware modules supported by Cisco MDS SAN-OS 4.x, see

Table 5 . For the list of MDS hardware

modules supported by Cisco MDS SAN-OS 3.x, see

Table 6

.

Module Support Matrix for Cisco MDS NX-OS 5.x

DS-X9530-SF2-K9

DS-X9530-SF2A-K9

DS-X9248-256K9

Description MDS 9500 Series MDS 9222i

NX-OS 5.2(x) NX-OS 5.0(x) NX-OS 5.2(x) NX-OS 5.0(x)

Yes Yes N/A N/A MDS 9500 Supervisor-2

Module

MDS 9500 Supervisor-2A

Module

MDS 9513 Fabric Module 3

MDS 9513 Fabric Module 2

Yes

Yes

Yes

MDS 9513 Fabric Module 1 Yes

8-port 10-Gbps FCoE Module Yes

1,2

32-port 8-Gbps Advanced Fibre

Channel Switching Module

Yes

1

48-port 8-Gbps Advanced Fibre

Channel Switching Module

Yes

1

24-port 8-Gbps Fibre Channel

Switching Module

Yes

1

48-port 8-Gbps Fibre Channel

Switching Module

Yes

1

4/44-port Host Optimized

8-Gbps Fibre Channel

Switching Module

Yes

Yes

No

Yes

Yes

No

No

No

Yes

Yes

Yes

3

3

N/A

N/A

N/A

N/A

No

No

No

No

No

Yes

N/A

N/A

N/A

N/A

No

No

No

No

No

Yes

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 9

MDS 9000 Chassis and Module Support

Table 4 Module Support Matrix for Cisco MDS NX-OS 5.x (continued)

Module

DS-X9316-SSNK9

DS-X9304-18K9

DS-X9112

DS-X9124

DS-X9148

DS-X9704

Description

16-port Storage Services Node

(SSN-16)

18/4-Port Multiservice Module

(MSM-18/4)

12-port 4-Gbps Fibre Channel

Switching Module

24-port 4-Gbps Fibre Channel

Switching Module

48-port 4-Gbps Fibre Channel

Switching Module

4-port 10-Gbps Fibre Channel

Switching Module

MDS 9500 Series MDS 9222i

NX-OS 5.2(x) NX-OS 5.0(x) NX-OS 5.2(x) NX-OS 5.0(x)

Yes Yes Yes Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

1.

Requires DS-13SLT-FAB3 or DS-13SLT-FAB2 in the MDS 9513.

2.

Requires the Supervisor-2A module.

3.

Requires DS-13SLT-FAB2 in the MDS 9513.

Table 5 Module Support Matrix for Cisco MDS NX-OS 4.x

Module

DS-X9530-SF2-K9

DS-X9530-SF2A-K9 MDS 9500 Supervisor-2A Module

DS-X9530-SF1-K9

DS-13SLT-FAB2

DS-13SLT-FAB1

DS-X9224-96K9

DS-X9248-96K9

DS-X9248-48K9

Description

MDS 9500 Supervisor-2 Module

MDS 9500 Supervisor-1 Module

MDS 9513 Fabric Module 2

MDS 9500 Series MDS 9222i MDS 9216i

Yes

Yes

1

N/A

N/A

N/A

N/A

No

Yes

MDS 9513 Fabric Module 1 Yes

24-port 8-Gbps Fibre Channel Switching Module Yes

2

48-port 8-Gbps Fibre Channel Switching Module Yes

2

4/44-port Host Optimized8-Gbps Fibre Channel

Switching Module

Yes

N/A

N/A

N/A

No

No

Yes

N/A

N/A

N/A

No

No

No

DS-X9316-SSNK9

DS-X9304-18K9

DS-X9112

DS-X9124

16-port Storage Services Node (SSN-16)

18/4-Port Multiservice Module (MSM-18/4)

Yes

Yes

12-port 4-Gbps Fibre Channel Switching Module Yes

24-port 4-Gbps Fibre Channel Switching Module Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

DS-X9148

DS-X9704

DS-X9302-14K9

DS-X9016

48-port 4-Gbps Fibre Channel Switching Module Yes

4-port 10-Gbps Fibre Channel Switching Module Yes

14/2-port Multiprotocol Services (MPS-14/2)

Module

16-port 1-, 2-Gbps Fibre Channel Switching

Module

Yes

Yes

Yes

Yes

No

No

Yes

Yes

Yes

Yes

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

10 OL-27554-07

MDS 9000 Chassis and Module Support

Table 5 Module Support Matrix for Cisco MDS NX-OS 4.x (continued)

Module

DS-X9032

DS-X9032-SSM

DS-X9308-SMIP

DS-X9304-SMIP

Description

32-port 1-, 2-Gbps Fibre Channel Switching

Module

32-port Storage Services Module (SSM)

8-port 1-, 2-Gbps IP Switching Module

4-port 1-, 2-Gbps IP Switching Module

MDS 9500 Series MDS 9222i

Yes

Yes

No

No

No

Yes

No

No

MDS 9216i

Yes

Yes

No

No

1.

In software releases earlier than Cisco NX-OS Release 4.2(7a), the Supervisor-2A module appears as unsupported hardware in Device Manager, but the

Supervisor-2A module does work with Cisco NX-OS release 4.x software.

2.

Requires DS-13SLT-FAB2 in the MDS 9513.

Table 6

lists the MDS hardware modules supported by Cisco MDS SAN-OS 3.x.

Table 6 Module Support Matrix for Cisco MDS SAN-OS 3.x

Module Description

DS-X9530-SF2-K9 MDS 9500 Supervisor-2 Module

DS-X9530-SF2A-K9 MDS 9500 Supervisor-2A Module

DS-X9530-SF1-K9 MDS 9500 Supervisor-1 Module

DS-13SLT-FAB2 MDS 9513 Fabric Module 2

DS-13SLT-FAB1

DS-X9224-96K9

MDS 9513 Fabric Module 1

24-port 8-Gbps Fibre Channel Switching

Module

DS-X9248-96K9

DS-X9248-48K9

DS-X9316-SSNK9 16-port Storage Services Node (SSN-16)

DS-X9304-18K9 18/4-Port Multiservice Module

(MSM-18/4) 2

DS-X9112

DS-X9124

12-port 4-Gbps Fibre Channel Switching

Module

24-port 4-Gbps Fibre Channel Switching

Module

DS-X9148

48-port 8-Gbps Fibre Channel Switching

Module

4/44-port Host Optimized8-Gbps Fibre

Channel Switching Module

DS-X9704

DS-X9302-14K9

DS-X9016

No

No

No

Yes

Yes

Yes

48-port 4-Gbps Fibre Channel Switching

Module

4-port 10-Gbps Fibre Channel Switching

Module

Yes

Yes

14/2-port Multiprotocol Services

(MPS-14/2) Module

16-port 1-, 2-Gbps Fibre Channel Switching

Module

Yes

Yes

Yes

Yes

Yes

No

MDS 9500

Series

Yes

Yes 1

MDS

9222i

N/A

N/A

N/A

N/A

N/A

No

No

No

No

Yes

Yes

Yes

Yes

Yes

No

No

MDS

9216i

N/A

N/A

N/A

N/A

N/A

No

No

No

No

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

MDS

9216A

N/A

N/A

N/A

N/A

N/A

No

No

No

No

Yes

Yes

Yes

No

No

No

No

MDS

9216

N/A

N/A

N/A

N/A

N/A

No

No

No

No

No

Yes

Yes

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 11

Software Download Process

Table 6 Module Support Matrix for Cisco MDS SAN-OS 3.x (continued)

Module

DS-X9032

DS-X9032-SSM

DS-X9308-SMIP

DS-X9304-SMIP

Description

32-port 1-, 2-Gbps Fibre Channel Switching

Module

MDS 9500

Series

Yes

32-port Storage Services Module (SSM)

8-port 1-, 2-Gbps IP Switching Module

4-port 1-, 2-Gbps IP Switching Module

Yes

Yes

Yes

MDS

9222i

No

Yes

No

Yes

MDS

9216i

Yes

Yes

Yes

Yes

MDS

9216A

Yes

Yes

Yes

Yes

MDS

9216

Yes

Yes

Yes

Yes

1.

In software releases earlier than Cisco NX-OS Release 3.3(5a), the Supervisor-2A module appears as unsupported hardware in Device Manager, but the

Supervisor-2A module does work with Cisco NX-OS release 3.x software.

2.

Cisco SAN-OS Release 3.2(1) and later support the 18/4-Port Multiservice Module (MSM-18/4).

Software Download Process

Use the software download procedure to upgrade to a later version, or downgrade to an earlier version, of an operating system. This section describes the software download process for the Cisco MDS NX-OS software and includes the following topics:

Determining the Software Version, page 12

Determining Software Version Compatibility, page 12

Downloading Software, page 13

Selecting the Correct Software Image for an MDS 9100 Series Switch, page 14

Selecting the Correct Software Image for an MDS 9200 Series Switch, page 14

Selecting the Correct Software Image for an MDS 9500 Series Switch, page 14

NPE Software Images, page 15

Determining the Software Version

To determine the version of Cisco MDS NX-OS or SAN-OS software currently running on a Cisco MDS

9000 Family switch using the CLI, log in to the switch and enter the show version EXEC command.

To determine the version of Cisco MDS NX-OS or SAN-OS software currently running on a Cisco MDS

9000 Family switch using Cisco DCNM for SAN, view the Switches tab in the Information pane, locate the switch using the IP address, logical name, or WWN, and check its version in the Release column.

Determining Software Version Compatibility

Table 7 lists the software versions that are compatible in a mixed SAN environment, the minimum

software versions that are supported, and the versions that have been tested. We recommend that you use the latest software release supported by your vendor for all Cisco MDS 9000 Family products.

12

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Software Download Process

Table 7 Software Release Compatibility

Cisco NX-OS Software

NX-OS Release 5.2(8c)

Minimum NX-OS or SAN-OS

Release

Tested NX-OS and SAN-OS

Releases

NX-OS Release 5.0(1a) or later NX-OS Release 5.0(1a) and later

NX-OS Release 4.2(3) or later NX-OS Release 4.2(3) and later

SAN-OS Release 3.3(5) or later SAN-OS Release 3.3(5) and later

Downloading Software

The Cisco MDS NX-OS software is designed for mission-critical high availability environments. To realize the benefits from nondisruptive upgrades on the Cisco MDS 9500 Directors, we highly recommend that you install dual supervisor modules.

To download the latest Cisco MDS NX-OS software, access the Software Center at this URL: http://www.cisco.com/cisco/software/navigator.html?a=a&i=rpm

See the following sections in this release note for details on how you can nondisruptively upgrade your

Cisco MDS 9000 switch. Issuing the install all command from the CLI, or using Cisco DCNM for SAN to perform the downgrade, enables the compatibility check. The check indicates if the upgrade can happen nondisruptively or disruptively depending on the current configuration of your switch and the reason.

Compatibility check is done:

Module bootable Impact Install-type Reason

------ -------- -------------- ------------ ------

1 yes non-disruptive rolling

2 yes disruptive rolling Hitless upgrade is not supported

3 yes disruptive rolling Hitless upgrade is not supported

4 yes non-disruptive rolling

5 yes non-disruptive reset

6 yes non-disruptive reset

At a minimum, you need to disable the default device alias distribution feature using the no device-alias

distribute command in global configuration mode. The show incompatibility system bootflash:system

image filename command determines which additional features need to be disabled.

Note If you would like to request a copy of the source code under the terms of either GPL or LGPL, send an e-mail to [email protected].

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

13

Software Download Process

Selecting the Correct Software Image for an MDS 9100 Series Switch

The system and kickstart image that you use for an MDS 9100 Series switch depends on which switch you use, as shown in

Table 8 .

Table 8 Software Images for MDS 9100 Series Switches

Cisco MDS 9100 Series Switch Type

MDS 9134,

MDS 9124,

Cisco MDs 4-Gbps Fabric Switch for HP c-Class BladeSystem,

Cisco MDS 4-Gbps Fabric Switch for IBM

BladeCenter

MDS 9148,

Cisco MDS 8Gb Fabric Switch for HP c-Class BladeSystem

Naming Convention

Filename begins with m9100-s2ek9

Filename begins with m9100-s3ek9

Selecting the Correct Software Image for an MDS 9200 Series Switch

The system and kickstart image that you use for an MDS 9200 series switch depends on which switch you use, as shown in

Table 9 .

Table 9 Software Images for MDS 9200 Series Switches

Cisco MDS 9200 Series Switch Type

MDS 9222i

Naming Convention

Filename begins with m9200-s2ek9

Selecting the Correct Software Image for an MDS 9500 Series Switch

The system and kickstart image that you use for an MDS 9500 Series are for switches with a

Supervisor-2 module, as shown in

Table 10 . Cisco NX-OS Release 5.x and Release 4.x do not support

the Supervisor-1 module.

Table 10 Software Images for Supervisor Type

Cisco MDS 9500 Series Switch

Type

MDS 9513, 9509, and 9506

Supervisor Module Type Naming Convention

Supervisor-2 module

Supervisor-2A module

Filename begins with m9500-sf2ek9

Use the show module command to display the type of supervisor module in the switch. The following is sample output from the show module command on a Supervisor-2 module: switch# show module

Mod Ports Module-Type Model Status

--- ----- -------------------------------- ------------------ ------------

...

...

7 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *

8 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standby

14

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Upgrading Your Cisco MDS NX-OS Software Image

NPE Software Images

No payload encryption (NPE) images are available with some releases of Cisco MDS NX-OS Release

5.2(x) software. The NPE images are intended for countries who have import restrictions on products that encrypt payload data.

To differentiate an NPE image from the standard software image, the letters npe are included in the image name as follows:

• m9500-sf2ek9-kickstart-mz-npe.5.2.2.bin

m9500-sf2ek9-mz-npe.5.2.2.bin

When downloading software, ensure that you select the correct software images for you Cisco MDS

9000 Series switch. Nondisruptive software upgrades or downgrades between NPE images and non-NPE images are not supported.

Upgrading Your Cisco MDS NX-OS Software Image

This section lists the guidelines recommended for upgrading your Cisco MDS NX-OS software image and includes the following topics:

Upgrading Guidelines Specific to NX-OS Release 5.2(8c), page 15

General Upgrading Guidelines, page 17

Nondisruptive Upgrade Paths, page 17

FICON Supported Releases and Upgrade Paths, page 19

Note Before you begin the upgrade process, review the list of chassis and modules that Cisco MDS NX-OS

Release 5.2(8c) supports. See the

“MDS 9000 Chassis and Module Support” section on page 8 .

For detailed instructions for performing a software upgrade using Cisco DCNM, see the Cisco DCNM

Release Notes, Release 5.2, which is available from the following website: http://www.cisco.com/en/US/products/ps10495/prod_release_notes_list.html

Upgrading Guidelines Specific to NX-OS Release 5.2(8c)

Follow these guidelines when upgrading to Cisco MDS NX-OS Release 5.2(8c):

Follow the upgrade path to NX-OS Release 5.2(8c) that is specified in

Table 11

.

Upgrade to NX-OS Release 5.2(x) before you install any Generation 4 module in an MDS 9500

Series switch. Cisco MDS DS-X9232-256K9 and DS-X9248-256K9 switching modules include the

FCoE module and the 32-port and 48-port 8-Gbps Advanced Fibre Channel modules. NX-OS

Release 5.2(x) is needed for the switch to recognize the new hardware.

Perform a full switch reload on an MDS 9509 or MDS 9506 switch after you install NX-OS Release

5.2(1) and install any Cisco MDS DS-X9232-256K9 and DS-X9248-256K9 switching modules, including the FCoE module. The switch reload is required for the new hardware to come up. Once you perform the switch reload, the fabric mode changes to support the Cisco MDS

DS-X9232-256K9 and DS-X9248-256K9 switching modules hardware. Because of the changed

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

15

Upgrading Your Cisco MDS NX-OS Software Image

16

• fabric mode, you cannot subsequently perform a nondisruptive software downgrade from NX-OS

Release 5.2(1). For additional information, see the “Downgrading Guidelines Specific to NX-OS

Release 5.2(8c)” section on page 20 .

Ensure that you have a Supervisor-2A module (DS-X9530-SF2A-K9) installed in a MDS 9500

Series switch if you plan to use the Cisco MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet

(FCoE) (DS-X9708-K9).

We recommend that you delete any SPAN configuration, Fibre Channel tunnel, or tunnel-ID map configuration from your switch before you start the upgrade to NX-OS Release 5.2(1). You can save the SPAN destination and SPAN target configuration and then reconfigure the SPAN session following the upgrade. All SPAN destination and SPAN target ports are reinitialized after the upgrade. To gather information about SPAN sessions and delete them, use the following commands in this order:

show incompatibility systems bootflash:image_name to display any incompatible configurations

show span session to check the current configuration for a SPAN session

no span session session-number to delete a SPAN session

show running-config | include fc-tunnel to check the current Fibre Channel tunnel configuration

no interface fc-tunnel y to delete a Fibre Channel tunnel on the switch that is the source for the

Fibre Channel tunnel

show interface brief | include SD to check the current configuration for a SPAN destination port configuration

show interface brief | include ST to check the current configuration for a SPAN target port configuration

no fc-tunnel tunnel-map z interface x/y to remove an Fibre Channel tunnel map

no switchport mode sd to negate the SPAN destination port mode for the SPAN destination port

no switchport mode st to negate the SPAN target port mode for the SPAN target port

If you are using IVR non-NAT mode, migrate to IVR-NAT mode before you upgrade to NX-OS

Release 5.2(1). IVR non-NAT mode is deprecated in NX-OS Release 5.2(1).

Note In dual SAN fabrics, IVR traffic can use one fabric while the other fabric is migrating. Only

IVR traffic is disrupted during the migration. Regular traffic within the VSAN is not disrupted during the migration.

To migrate to IVR-NAT mode, follow these steps:

1.

Stop or divert all applications on servers that depend on IVR.

If CFS distribution is not enabled for IVR, then perform steps 2 through 4 on all switches where

IVR is enabled.

If CFS distribution is enabled for IVR, then enter the ivr commit command following step 2, step 3, and step 4 to distribute the changes to other switches.

2.

3.

4.

5.

Deactivate the IVR zone set by entering the no ivr zoneset activate command.

Enable IVR NAT by entering the ivr nat command.

Activate the IVR zone set by entering the ivr zoneset activate command.

Start or reestablish all applications that were stopped in step 1.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Upgrading Your Cisco MDS NX-OS Software Image

The network can now run in IVR-NAT mode.

General Upgrading Guidelines

Follow these general guidelines before performing a software upgrade:

• Review the nondisruptive upgrade path to Release 5.2(8c) in

Table 11 .

Install and configure dual supervisor modules before the upgrade.

Issue the show install all impact upgrade-image CLI command to determine if your upgrade will be nondisruptive.

• Be aware that some features impact whether an upgrade is disruptive or nondisruptive:

Fibre Channel Ports: Fibre Channel ports can be nondisruptively upgraded without affecting traffic on the ports. See

Table 11

for the nondisruptive upgrade path for all NX-OS and SAN-OS releases.

Gigabit Ethernet Ports: Traffic on Gigabit Ethernet ports is disrupted during an upgrade or downgrade. This includes IPS modules and the Gigabit Ethernet ports on the MSM-18/4 module and the MDS 9222i switch. Those nodes that are members of VSANs traversing an FCIP ISL are impacted, and a fabric reconfiguration occurs. iSCSI initiators connected to the Gigabit

Ethernet ports lose connectivity to iSCSI targets while the upgrade is in progress.

FICON: If you have FICON enabled, the upgrade path is different. See the

“FICON Supported

Releases and Upgrade Paths” section on page 19

.

Note In addition to these guidelines, you may want to review the information in the

“Limitations and

Restrictions”

section prior to a software upgrade to determine if a feature may possibly behave differently following the upgrade.

Nondisruptive Upgrade Paths

Use Table 11

to determine your nondisruptive upgrade path to Cisco MDS NX-OS Release 5.2(8c). Find the image release number you are currently using in the “Current Release” column of the table and follow the steps in the order specified to perform the upgrade.

Note The software upgrade information in

Table 11

applies only to Fibre Channel switching traffic.

Upgrading system software disrupts IP traffic and intelligent services traffic.

Note Before upgrading to Cisco MDS NX-OS Release 5.2(8c) on a Cisco MDS 9509 or 9506 switch, see

Table 14

for specific guidelines.

OL-27554-07

Caution Upgrading to Cisco NX-OS Release 5.2(8c) without first upgrading to Release 5.0(x) is not recommended and is not supported, and might result in configuration loss. If you are upgrading to Cisco

NX-OS Release 5.2(8c) from any release other than Release 5.2(8b), 5.2(8a), Release 5.2(8), Release

5.2(6b), Release 5.2(6a), Release 5.2(6), Release 5.2(2d), Release 5.2(2a), Release 5.2(2), or Release

5.2(1), the only supported upgrade path to Release 5.2(8c) is from Release 5.0(x).

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

17

Upgrading Your Cisco MDS NX-OS Software Image

Table 11 Nondisruptive Upgrade Path to Cisco MDS NX-OS Release 5.2(8c)

Current Release

NX-OS:

Release 2.1(3),

2.1(2e), 2.1(2d), and

2.1(2b)

Nondisruptive Upgrade Path and Ordered Upgrade Steps

Release 5.2(1),

5.2(2), 5.2(2a),

5.2(2d), 5.2(6),

5.2(6a), 5.2(6b),

5.2(8), 5.2(8a),

5.2(8b)

Upgrade directly to NX-OS Release 5.2(8c).

All 5.0(x) releases Upgrade directly to NX-OS Release 5.2(8c).

All 4.2(x) releases and 4.1(x) releases

1.

2.

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

SAN-OS:

Release 3.3(2),

3.3(3), 3.3(4x), and

3.3(5x).

1.

2.

3.

1.

Upgrade to NX-OS Release 4.2(9).

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

Release 3.3(1c), all

3.2(x), 3.1(x), and

3.0(x) releases)

2.

Upgrade to SAN-OS Release 3.3(5b).

Upgrade to NX-OS Release 4.2(9).

3.

4.

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

1.

2.

3.

Upgrade to SAN-OS Release 3.3(1c).

Upgrade to SAN-OS Release 3.3(5b).

Upgrade to NX-OS Release 4.2(9).

4.

Release 2.1(2),

2.1(1b), 2.1(1a), and

2.0(x)

2.

3.

5.

1.

4.

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

Upgrade to SAN-OS Release 2.1(2b), 2.1(2d), 2.1(2e), or 2.1(3)

Upgrade to SAN-OS Release 3.3(1c).

Upgrade to SAN-OS Release 3.3(5).

Upgrade to NX-OS Release 4.2(9).

Release 1.x

1.

2.

5.

6.

5.

6.

3.

4.

7.

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

Upgrade to SAN-OS Release 1.3(4a).

Upgrade to SAN-OS Release 2.1(2b).

Upgrade to SAN-OS Release 3.3(1c).

Upgrade to SAN-OS Release 3.3(5b).

Upgrade to NX-OS Release 4.1(x) or 4.2(x).

Upgrade to NX-OS Release 5.0(x).

Upgrade to NX-OS Release 5.2(8c).

18

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Downgrading Your Cisco MDS SAN-OS Software Image

FICON Supported Releases and Upgrade Paths

Cisco MDS NX-OS Release 5.2(8c) is not a FICON-certified release.

Table 12

lists the SAN-OS and NX-OS releases that are certified for FICON. Refer to the specific release notes for FICON upgrade path information.

Table 12 FICON Supported Releases

FICON Supported Releases

NX-OS Release 5.2(2)

Release 4.2(7b)

Release 4.2(1b)

SAN-OS

Release 4.1(1c)

Release 3.3(1c)

Release 3.2(2c)

Release 3.0(3b)

Release 3.0(3)

Release 3.0(2)

Release 2.0(2b)

Use

Table 13 to determine the nondisruptive upgrade path for FICON-certified releases. Find the image

release number you are currently using in the Current Release with FICON Enabled column of the table and follow the recommended path.

Table 13 FICON Nondisruptive Upgrade Path

Current Release with FICON

Enabled

NX-OS Release 4.2(7b)

NX-OS Release 4.2(1b)

Upgrade Path

You can nondisruptively upgrade directly to NX-OS Release 5.2(2).

NX-OS Release 4.1(1c)

SAN-OS Release 3.3(1c)

SAN-OS Release 3.2(2c),

3.0(3b), 3.0(3), and 3.0(2).

You can nondisruptively upgrade directly to NX-OS Release 4.2(7b).

You can nondisruptively upgrade directly to NX-OS Release 4.2(1b).

You can nondisruptively upgrade directly to NX-OS Release 4.2(1b).

First upgrade to SAN-OS Release 3.3(1c), and then upgrade to NX-OS

Release 4.2(1b).

Downgrading Your Cisco MDS SAN-OS Software Image

This section lists the guidelines recommended for downgrading your Cisco MDS SAN-OS software image and includes the following topics:

Downgrading Guidelines Specific to NX-OS Release 5.2(8c), page 20

General Downgrading Guidelines, page 21

NX-OS Release 5.2(x) and Release 5.0(x) Software Downgrade and Upgrade Matrix for Cisco MDS

9509 and 9506 Switches, page 22

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 19

Downgrading Your Cisco MDS SAN-OS Software Image

Downgrading Guidelines Specific to NX-OS Release 5.2(8c)

The following guidelines apply to a downgrade from Cisco MDS NX-OS Release 5.2(8c):

• Cisco NX-OS Release 5.2(8c) and later releases support IDLE as a fill word for the switchport

fill-pattern command. Releases earlier than Release 5.2(8c) supported only the ARBFF fill word.

As a result, when you downgrade from Cisco NX-OS Release 5.2(8c) or a later release to an earlier release that does not support the IDLE fill word, the following syntax error occurs:

Syntax error while parsing 'switchport fill-pattern IDLE speed 8000'

The syntax error message is harmless and can be ignored.

You cannot nondisruptively downgrade from NX-OS Release 5.2(8c) to NX-OS Release 5.0(x) if you installed NX-OS Release 5.2(8c) on an MDS 9509 or MDS 9506 switch and you installed a

Generation 4 module in the switch and performed a full switch reload. The reason for this restriction is the change in fabric mode that occurs following the switch reload with the Generation 4 hardware installed. The downgrade will be disruptive, even if you remove the Generation 4 module prior to starting the downgrade.

If you do not install Generation 4 hardware or perform a full switch reload following the installation of NX-OS Release 5.2(c) on an MDS 9509 or MDS 9506 switch, you can nondisruptively downgrade to NX-OS Release 5.0(x).

If you have the Storage Media Encryption (SME) application configured on your system, you must delete signature clusters when downgrading from NX-OS Release 5.2(8c) to Release 5.2(1).

If smart zoning is enabled on your system and you want to downgrade nondisruptively to a version lower than NX-OS Release 5.2(6), you must disable smart zoning on all VSANs.

Following an ISSD from Cisco NX-OS Release 5.2(8c) to an earlier Release 5.2(x) or to Release

5.0(x) on a Cisco MDS 9000 switch that is configured with IVR or FCR, reload the modules with the ELS trap entry. In the case of FCR, reload the module with the FCR device logged in. For IVR, all modules should be reloaded.

We recommend that you delete any SPAN configuration, Fibre Channel tunnel, or tunnel-ID map configuration from your switch before you downgrade from NX-OS Release 5.2(8c) to a lower version. If any SPAN session, SPAN destination, SPAN target, or Fibre Channel tunnel interface is configured, the installer should detect it and prompt you to delete these configurations.

To gather information about SPAN sessions and delete them, use the following commands in this order:

show incompatibility systems bootflash:image_name to display any incompatible configurations

show span session to check the current configuration for a SPAN session

no span session session-number to delete a SPAN session

show running-config | include fc-tunnel to check the current Fibre Channel tunnel configuration

no interface fc-tunnel y to delete a Fibre Channel tunnel on the switch that is the source for the

Fibre Channel tunnel

show interface brief | include SD to check the current configuration for a SPAN destination port configuration

show interface brief | include ST to check the current configuration for a SPAN target port configuration

no fc-tunnel tunnel-map z interface x/y to remove an Fibre Channel tunnel map

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

20 OL-27554-07

Downgrading Your Cisco MDS SAN-OS Software Image

no switchport mode sd to negate the SPAN destination port mode for the SPAN destination port

no switchport mode st to negate the SPAN target port mode for the SPAN target port

General Downgrading Guidelines

Follow these general guidelines before you perform a a software downgrade:

Issue the system no acl-adjacency-sharing execute command to disable ACL adjacency usage on

Generation 2 and Generation 1 modules. If this command fails, reduce the number of zones, IVR zones, TE ports, or a combination of these in the system and issue the command again.

Disable all features not supported by the downgrade release. Use the show incompatibility system

downgrade-image command to determine what you need to disable.

Use the show install all impact downgrade-image command to determine if your downgrade will be nondisruptive.

Be aware that some features impact whether a downgrade is disruptive or nondisruptive:

FCoE: Fibre Channel over Ethernet requires Cisco NX-OS Release 5.2(x). A downgrade from

Release 5.2(x) disrupts and stops all FCoE traffic.

Fibre Channel Ports: Fibre Channel ports can be nondisruptively downgraded without affecting traffic on the ports. See

Table 15

for the nondisruptive downgrade path for all SAN-OS releases.

Gigabit Ethernet Ports: Traffic on Gigabit Ethernet ports is disrupted during a downgrade.

This includes IPS modules and the Gigabit Ethernet ports on the MSM-18/4 module, and the

MDS 9222i switch. Those nodes that are members of VSANs traversing an FCIP ISL are impacted, and a fabric reconfiguration occurs. iSCSI initiators connected to the Gigabit

Ethernet ports lose connectivity to iSCSI targets while the downgrade is in progress.

FICON: If you have FICON enabled, the downgrade path is different. See the

“FICON

Downgrade Paths” section on page 24 .

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

21

Downgrading Your Cisco MDS SAN-OS Software Image

NX-OS Release 5.2(x) and Release 5.0(x) Software Downgrade and Upgrade

Matrix for Cisco MDS 9509 and 9506 Switches

See the compatibility information in

Table 14 to determine if a downgrade to or upgrade from Release

5.0(x) software is disruptive or nondisruptive on a Cisco MDS 9509 or 9506 switch.

Table 14 NX-OS Release 5.2(x) and Release 5.0(x) Downgrade and Upgrade Matrix

Downgrade Path on a Cisco MDS 9509 or 9506 Switch

Current Release Desired Release Expected Behavior

5.2(8c)

5.2(2d)

5.2(x)

5.0(7) or 5.0(8)

5.2(5b), 5.2(6a), 5.2(6),

5.2(2d), 5.2(2a), or

5.2(1)

5.2(2a) or 5.2(1)

Nondisruptive

Nondisruptive

Disruptive 5.0(7) or 5.0(8)

5.0(1a), 5.0(1b), or

5.0(4)

Disruptive

5.0(7) or 5.0(8)

5.0(4)

5.0(1a), 5.0(1b), or

5.0(4)

4.2(x) or 4.1(x)

5.0(1a)

4.2(x) or 4.1(x)

Disruptive

Nondisruptive

Nondisruptive

Observed Behavior

Nondisruptive

Nondisruptive

Disruptive

Nondisruptive

The user is expected to explicitly reload the switch using the reload command.

Disruptive

Nondisruptive

Nondisruptive

Upgrade Path on a Cisco MDS 9509 or 9506 Switch

Current Release Desired Release

5.2(1), 5.2(2a), 5.2(2d),

5.2(6), 5.2(6a), 5.2(6b),

5.2(8), 5.2(8a), 5.2(8a)

5.2(8c)

5.2(1) or 5.2(2a)

5.0(7) or 5.0(8)

5.2(2d)

5.2(x)

5.0(1a), 5.0(1b), or

5.0(4)

5.2(x)

Expected Behavior

Nondisruptive

Nondisruptive

Nondisruptive

Support for Generation

4 modules is available.

Nondisruptive

Support for Generation

4 modules is not available.

Observed Behavior

Nondisruptive

Nondisruptive

Nondisruptive

Support for Generation

4 modules is available.

Nondisruptive

Support for Generation

4 modules is not available.

Use Table 15 to determine the nondisruptive downgrade path from Cisco NX-OS Release 5.2(8c). Find

the NX-OS or SAN-OS image that you want to downgrade to in the To SAN-OS Release column of the table and follow the steps in the order specified to perform the downgrade.

Note The software downgrade information in

Table 15

applies only to Fibre Channel switching traffic.

Downgrading system software disrupts IP and intelligent services traffic.

22

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Downgrading Your Cisco MDS SAN-OS Software Image

OL-27554-07

Table 15 Nondisruptive Downgrade Path from NX-OS Release 5.2(8c)

To NX-OS or SAN-OS

Release

NX-OS:

Nondisruptive Downgrade Path and Ordered Downgrade Steps

Release 5.2(1), 5.2(2),

5.2(2a), 5.2(2d),

5.2(6), 5.2(6a), and

5.2(6b), 5.2(8),

5.2(8a), 5.2(8a)

Downgrade directly from NX-OS Release 5.2(8c).

All 5.0(x) releases Downgrade directly from NX-OS Release 5.2(8c)

1, 2, 3

All 4.2(x) and 4.1(x) releases

1.

2.

Downgrade to NX-OS Release 5.0(x).

Downgrade to NX-OS Release 4.2(x) or 4.1(x).

SAN-OS:

All 3.3(x) releases 1.

2.

Downgrade to NX-OS Release 5.0(x).

Downgrade to NX-OS Release 4.2(x) or Release 4.1(x).

3.

1.

All 3.2(x), 3.1(x),

3.0(x) releases, and all

2.1(x) releases.

2.

3.

4.

Downgrade to SAN-OS Release 3.3(x).

Downgrade to NX-OS Release 5.0(x).

Downgrade to NX-OS Release 4.2(x) or Release 4.1(x).

Downgrade to SAN-OS Release 3.3(x).

All 2.0(x) releases. 1.

2.

3.

Downgrade to SAN-OS Release 3.2(x), Release 3.1(x)., Release 3.0(x), or

Release 2.1(x).

Downgrade to NX-OS Release 5.0(x).

Downgrade to NX-OS Release 4.2(x) or Release 4.1(x).

Release 1.x

1.

2.

4.

5.

Downgrade to SAN-OS Release 3.3(x).

Downgrade to SAN-OS Release 2.1(2x).

Downgrade to SAN-OS Release 2.0(x).

Downgrade to NX-OS Release 5.0(x).

3.

4.

5.

6.

Downgrade to NX-OS Release 4.2(x) or Release 4.1(x).

Downgrade to SAN-OS Release 3.3(x).

Downgrade to SAN-OS Release 2.1(2b).

Downgrade to SAN-OS Release 1.3(4a).

Downgrade to SAN-OS Release 1.x.

1.

Before downgrading to NX-OS Release 5.0(8a), 5.0(8) or Release 5.0(7) on an MDS 9509 or MDS 9506 switch, see

“NX-OS

Release 5.2(x) and Release 5.0(x) Software Downgrade and Upgrade Matrix for Cisco MDS 9509 and 9506 Switches” section on page 22

.

2.

If you install a Generation 4 module in an MDS 9509 or MDS 9506 switch and perform a full switch reload following the installation of NX-OS Release 5.2(8c), you cannot nondisruptively download from NX-OS Release 5.2(8a) to NX-OS 5.0(x).

3.

A downgrade from NX-OS Release 5.2(8c) to a release other than Release 5.2(1), 5.2(2), 5.2(2a), 5.2(2d), 5.2(6), 5.2(6a),

5.2(6b), 5.2(8a), or 5.2(8b) disrupts and stops all FCoE traffic because FCoE requires Cisco NX-OS Release 5.2(x).

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

23

New Features in Cisco MDS NX-OS Release 5.2

FICON Downgrade Paths

Table 16

Table 16

lists the downgrade paths for FICON releases. Find the image release number that you want to downgrade to in the

To Release with FICON Enabled column of the table and follow the recommended

downgrade path.

FICON Downgrade Path

To Release with FICON Enabled

NX-OS Release 4.2(7b)

NX-OS Release 4.2(1b)

NX-OS Release 4.1(1c)

SAN-OS 3.3(1c)

SAN-OS 3.2(2c)

SAN-OS 3.0(3b)

SAN-OS 3.0(2)

Downgrade Path

You can nondisruptively downgrade directly from NX-OS Release 5.2(2).

You can nondisruptively downgrade directly from NX-OS Release 4.2(7b).

You can nondisruptively downgrade directly from NX-OS Release 4.2(1b).

You can nondisruptively downgrade directly from NX-OS Release 4.1(1c).

First downgrade to SAN-OS Release 3.3(1c) and then downgrade to Release

3.2(2c).

First downgrade to SAN-OS Release 3.3(1c) and then downgrade to Release

3.0(3b).

First downgrade to SAN-OS Release 3.3(1c) and then downgrade to Release

3.0(2).

New Features in Cisco MDS NX-OS Release 5.2

This section lists the new software and hardware features in Cisco MDS NX-OS Release 5.2. It includes the following topics:

New Features in Cisco MDS NX-OS Release 5.2(8c), page 25

New Features in Cisco MDS NX-OS Release 5.2(8b), page 25

New Features in Cisco MDS NX-OS Release 5.2(8a), page 25

New Features in Cisco MDS NX-OS Release 5.2(8), page 25

New Features in Cisco MDS NX-OS Release 5.2(6b), page 25

New Features in Cisco MDS NX-OS Release 5.2(6a), page 25

New Features in Cisco MDS NX-OS Release 5.2(6), page 25

New Features in Cisco MDS NX-OS Release 5.2(2d), page 26

New Features in Cisco MDS NX-OS Release 5.2(2d), page 26

New Features in Cisco MDS NX-OS Release 5.2(2), page 26

New Features in Cisco MDS NX-OS Release 5.2(1), page 27

New Hardware in Cisco MDS NX-OS Release 5.2(1), page 28

Product information about Cisco MDS 9000 NX-OS software is available at this link: http://www.cisco.com/en/US/products/ps5989/index.html

24

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

New Features in Cisco MDS NX-OS Release 5.2

New Features in Cisco MDS NX-OS Release 5.2(8c)

Cisco MDS NX-OS Release 5.2(8c) is a maintenance release that includes bug fixes. It does not include new features.

New Features in Cisco MDS NX-OS Release 5.2(8b)

Cisco MDS NX-OS Release 5.2(8b) is a maintenance release that includes bug fixes. It does not include new features.

New Features in Cisco MDS NX-OS Release 5.2(8a)

Cisco MDS NX-OS Release 5.2(8a) is a maintenance release that includes bug fixes. It does not include new features.

New Features in Cisco MDS NX-OS Release 5.2(8)

Cisco MDS NX-OS Release 5.2(8) is a maintenance release that includes bug fixes. It does not include new features.

New Features in Cisco MDS NX-OS Release 5.2(6b)

Cisco MDS NX-OS Release 5.2(6b) is a maintenance release that includes bug fixes. It does not include new features.

New Features in Cisco MDS NX-OS Release 5.2(6a)

Cisco MDS NX-OS Release 5.2(6a) is a maintenance release that includes bug fixes and a scalability improvement for the following feature:

• Cisco I/O Accelerator

Starting with Cisco MDS NX-OS Release 5.2(6a), the number of supported I/O Accelerator (IOA) flows has increased to 1000.

New Features in Cisco MDS NX-OS Release 5.2(6)

Cisco MDS NX-OS Release 5.2(6) includes the new features described in the following sections:

Smart Zoning, page 26

Storage Media Encryption Features, page 26

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

25

New Features in Cisco MDS NX-OS Release 5.2

Smart Zoning

Cisco Smart Zoning simplifies the process of zoning to reduce the burden on administrators while simultaneously provisioning zone-related hardware resources on Cisco Fibre Channel switching modules more efficiently.

For more information on configuring and deploying Smart Zoning, see the Cisco MDS 9000 Fabric

Configuration Guide.

Storage Media Encryption Features

Cisco NX-OS Release 5.2(6) includes the following enhancements to Cisco Storage Media Encryption

(SME) Disk:

SME Disk now supports greater than 2 TB LUNs for both signature and non-signature mode.

SME Disk signature mode allows snapshots of a crypto LUN across key change operations.

SME Disk signature mode automatically recognizes snapshots that are exposed to the host, based on the media signature.

SME Disk now supports Master Key Rekey (MKR) on a cluster for both signature and non-signature mode.

These enhancements require Cisco NX-OS Release 5.2(6) and Cisco DCNM Release 6.1(1a). For more information on these feature enhancements, see the Cisco MDS 9000 Family NX-OS Storage Media

Encryption Configuration Guide.

New Features in Cisco MDS NX-OS Release 5.2(2d)

Cisco MDS NX-OS Release 5.2(2d) is a maintenance release that includes bug fixes. It does not include any new features.

New Features in Cisco MDS NX-OS Release 5.2(2a)

Cisco MDS NX-OS Release 5.2(2a) is a maintenance release that includes bug fixes and the following feature enhancement:

• Port Monitor

Port monitoring has been enhanced with several ASIC counters that monitor and report internal packet drops.

Additional information about this feature enhancement is available in the Cisco MDS 9000 Series

Interfaces Configuration Guide.

New Features in Cisco MDS NX-OS Release 5.2(2)

Cisco MDS NX-OS Release 5.2(2) is a FICON-certified version of Cisco MDS NX-OS Release 5.2(1), that also includes new features and bug fixes. In addition to these features, Cisco MDS NX-OS Release

5.2(2) supports all the new software features and new hardware that were introduced in Cisco MDS

NX-OS Release 5.2(1).

Cisco MDS NX-OS Release 5.2(2) supports the following software features:

26

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

New Features in Cisco MDS NX-OS Release 5.2

FICON Certification

Cisco MDS NX-OS Release 5.2(2) is a FICON-certified release that supports these features:

– Nondisruptive software upgrades to and downgrades from Cisco NX-OS Release 4.2(7b), which is the previous FICON-certified release.

FICON FCIP on the Cisco MDS 9000 SSN-16 module, including FICON Tape Acceleration and

XRC Acceleration.

FICON Tape Acceleration for ESCON through Optica PRIZM.

– FICON support on the Cisco MDS 9000 32-port 8-Gbps Advanced Fibre Channel Switching module, the Cisco MDS 9000 48-port 8-Gbps Advanced Fibre Channel Switching module, and the Cisco MDS 9513 Switching Fabric 3 module (DS-13SLT-FAB3).

Availability of Cisco MDS NX-OS Release 5.2 on Cisco MDS 9100 Series Fabric Switches

Cisco MDS NX-OS Release 5.2(2) supports the following switches (which are not supported by

Cisco MDS NX-OS Release 5.2(1)):

– Cisco MDS 9134 Fabric Switch

Cisco MDS 9124 Fabric Switch

Cisco MDs 4-Gbps Fabric Switch for HP c-Class BladeSystem

– Cisco MDS 4-Gbps Fabric Switch for IBM BladeCenter

Port Group Monitoring

Port group monitoring and SNMP are available on the Cisco MDS 9000 32-port 8-Gbps Advanced

Fibre Channel Switching module and the Cisco MDS 9000 48-port 8-Gbps Advanced Fibre Channel

Switching module.

Availability of IVR on the Cisco MDS 9148 Switch

Cisco MDS NX-OS Release 5.2(2) supports Inter-VSAN Routing (IVR) on the Cisco MS 9148 multilayer fabric switch.

IOA with NPV

Cisco MDS NX-OS Release 5.2(2) supports configuring IOA with NPV.

New Features in Cisco MDS NX-OS Release 5.2(1)

Cisco MDS NX-OS Release 5.2(1) supports the following software features:

• Software support for the MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet (FCoE) module

The MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet (FCoE) module is a multihop-capable

FCoE module for the core data center. This full line-rate FCoE module for the MDS 9500 Series

Director switches allows you to extend FCoE benefits beyond the access layer into the data center core. FCoE supports I/O consolidation by preserving all Fibre Channel constructs, and maintaining the same latency, security, and traffic management attributes of Fibre Channel. In addition, FCoE extends Fibre Channel SAN connectivity to Cisco Nexus 7000 switches that are FCoE capable.

• Software support for Cisco MDS 9000 Family 8-Gbps Advanced Fibre Channel Switching Modules

Cisco NX-OS Release 5.2(1) includes software support for the 32-port and the 48-port 8-Gbps

Advanced Fibre Channel switching modules that can be used in the MDS 9500 Series Directors. The

MDS 9513 Multilayer Director can be upgraded with the new Generation 4 Fabric-3 module to

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

27

New Features in Cisco MDS NX-OS Release 5.2

• increase bandwidth to 256 Gbps per slot. In addition, the 8-Gbps Advance Fibre Channel switching module support speeds of 10 Gbps on the MDS 9513 with the Fabric-3 module installed. The upgrade from the Fabric-2 module to the Fabric-3 module is nondisruptive.

Cisco MDS 9000 8-Gbps Advanced Fibre Channel switching modules support Cisco FlexSpeed technology that enables ports to be configured as either 1-, 2-, 4-, or 8-Gbps, or 10-Gbps Fibre

Channel interfaces.

Cisco MDS 9000 8-Gbps Advanced Fibre Channel switching modules support Arbitrated Local

Switching to locally switch traffic at line rate 8-Gbps in a fair manner across all ports on the module through central arbitration.

Storage Media Encryption for Disk

The Storage Media Encryption (SME) solution, which currently protects data at rest on heterogeneous tape drives and virtual tape libraries (VTLs), has been enhanced to encrypt data on disk arrays in a SAN environment using secure IEEE-standard Advanced Encryption Standard

(AES) algorithms.

SME Disk requires the Storage Media Encryption Package license.

See the Cisco MDS 9000 Family Storage Media Encryption Configuration Guide for more information on configuring and deploying SME Disk.

• Cisco Data Center Network Manager for SAN

Cisco Fabric Manager and Cisco Data Center Network Manager have merged into a unified product that can now manage and monitor both SAN and LAN environments. As a part of this merger, Cisco

Fabric Manager has been rebranded as Cisco DCNM for SAN.

As a part of NX-OS Release 5.2(1), Cisco DCNM for SAN introduces server-based licenses that allow you to purchase a pool of Cisco DCNM for SAN licenses instead of a switch-based Fabric

Manager Server (FMS) license. The installed base of existing FMS licenses are grandfathered into

Cisco DCNM for SAN, which means that you do not have to purchase a new license to use Cisco

DCNM for SAN if you have an existing FMS license.

There are many new features in Cisco DCNM for SAN, including:

Summary and host dashboards

VMware topology and performance

Performance forecasting charts

External SMI-S 1.4 agent

– FCoE provisioning and management

Detailed information about Cisco DCNM features is available in the Cisco DCNM Release Notes,

Release 5.2, and in the feature configuration guides for Cisco DCNM for SAN.

For additional information about Cisco MDS NX-OS Release 5.2(1), see the Cisco MDS 9000 Family

Release Notes for Cisco MDS NX-OS Release 5.2(1).

New Hardware in Cisco MDS NX-OS Release 5.2(1)

Cisco MDS NX-OS Release 5.2(1) supports the following new Generation 4 hardware devices:

Cisco MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet (FCoE) module (DS-X9708-K9)

Cisco MDS 9000 32-port 8-Gbps Advanced Fibre Channel Switching module (DS-X9232-256K9)

Cisco MDS 9000 48-port 8-Gbps Advanced Fibre Channel Switching module (DS-X9248-256K9)

28

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Licensed Cisco NX-OS Software Packages

• Cisco MDS 9513 Switching Fabric 3 module (DS-13SLT-FAB3)

See the Cisco MDS 9500 Series Hardware Installation Guide for descriptions of, and specifications for the new Generation 4 modules. This guide also provides instructions for migrating to the new Fabric 3 module and guidelines for installing the new 8-Gbps Advanced Fibre Channel switching modules.

Licensed Cisco NX-OS Software Packages

Most Cisco MDS 9000 family software features are included in the standard package. However, some features are logically grouped into add-on packages that must be licensed separately, such as the Cisco

MDS 9000 Enterprise package, SAN Extension over IP package, Mainframe package, Storage Services

Enabler (SSE) package, Storage Media Encryption package, and Data Mobility Manager package.

On-demand ports activation licenses are also available for the Cisco MDS Blade Switch Series and

4-Gbps Cisco MDS 9100 Series Multilayer Fabric switches.

Note A license is not required to use the Cisco MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet (FCoE) module (DS-X9708-K9).

Enterprise Package

The standard software package that is bundled at no charge with the Cisco MDS 9000 Family switches includes the base set of features that Cisco believes are required by most customers for building a SAN.

The Cisco MDS 9000 family also has a set of advanced features that are recommended for all enterprise

SANs. These features are bundled together in the Cisco MDS 9000 Enterprise package. Refer to the

Cisco MDS 9000 Enterprise package fact sheet for more information.

SAN Extension over IP Package

The Cisco MDS 9000 SAN Extension over IP package allows the customer to use FCIP to extend SANs over wide distances on IP networks using the Cisco MDS 9000 family IP storage services. Refer to the

Cisco MDS 9000 SAN Extension over IP package fact sheet for more information.

Mainframe Package

The Cisco MDS 9000 Mainframe package uses the FICON protocol and allows control unit port management for in-band management from IBM S/390 and z/900 processors. FICON VSAN support is provided to help ensure true hardware-based separation of FICON and open systems. Switch cascading, fabric binding, and intermixing are also included in this package. Refer to the Cisco MDS 9000

Mainframe package fact sheet for more information.

Storage Media Encryption Package

The Cisco MDS 9000 Storage Media Encryption package enables encryption of data at rest on heterogeneous tape devices, virtual tape libraries, and disk arrays as a transparent fabric service. Cisco

SME is completely integrated with Cisco MDS 9000 Family switches and the Cisco DCNM for SAN application, enabling highly available encryption services to be deployed without rewiring or

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 29

Licensed Cisco NX-OS Software Packages reconfiguring SANs, and allowing them to be managed easily without installing additional management software. Refer to the Cisco MDS 9000 Storage Media Encryption package fact sheet for more information. The Storage Media Encryption package is for use only with Cisco MDS 9000 Family switches.

Data Mobility Manager Package

The Cisco MDS 9000 Data Mobility Manager package enables data migration between heterogeneous disk arrays without introducing a virtualization layer or rewiring or reconfiguring SANs. Cisco DMM allows concurrent migration between multiple LUNs of unequal size. Rate-adjusted migration, data verification, dual Fibre Channel fabric support, and management using Cisco DCNM for SAN provide a complete solution that greatly simplifies and eliminates most downtime associated with data migration.

Refer to the Cisco MDS 9000 Data Mobility Manager package fact sheet for more information. The Data

Mobility Manager package is for use only with Cisco MDS 9000 Family switches.

Storage Services Enabler Package

The Cisco MDS 9000 SSE package allows network-based storage applications and services to run on the

Cisco MDS 9000 family SSMs, Cisco MDS 9000 18/4-Port Multiservice Module (MSM-18/4), and

Cisco MDS 9222i. Intelligent fabric applications simplify complex IT storage environments and help organizations gain control of capital and operating costs by providing consistent and automated storage management. Refer to the Cisco MDS 9000 SSE package fact sheet for more information.

On-Demand Port Activation License

On-demand ports allow customers to benefit from Cisco NX-OS Software features while initially purchasing only a small number of activated ports on 8-Gbps or 4-Gbps Cisco MDS 9100 Series

Multilayer Fabric switches. As needed, customers can expand switch connectivity by licensing additional ports.

I/O Accelerator Package

The Cisco I/O Accelerator (IOA) package activates IOA on the Cisco MDS 9222i fabric switch, the

Cisco MDS 9000 18/4 Multiservice Module (MSM-18/4), and on the SSN-16 module. The IOA package is licensed per service engine and is tied to the chassis. The number of licenses required is equal to the number of service engines on which the intelligent fabric application is used.The SSN-16 requires a separate license for each engine on which you want to run IOA. Each SSN-16 engine that you configure for IOA checks out a license from the pool managed at the chassis level. SSN-16 IOA licenses are available as single licenses.

XRC Acceleration License

The Cisco Extended Remote Copy (XRC) acceleration license activates FICON XRC acceleration on the

Cisco MDS 9222i switch and on the MSM-18/4 in the Cisco MDS 9500 Series directors. One license per chassis is required. You must install the Mainframe Package and the SAN Extension over FCIP Package before you install the XRC acceleration license. The Mainframe Package enables the underlying FICON support, and the FCIP license or licenses enable the underlying FCIP support.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

30 OL-27554-07

Deprecated Features

Deprecated Features

Cisco MDS NX-OS Release 5.2 no longer supports the features listed in the following sections:

Zoning Features, page 31

SNIA Common Information Model, page 31

IVR Non-NAT Mode, page 31

Zoning Features

LUN zoning, read-only zones, and broadcast zones are no longer supported. These features affect the following hardware:

• Cisco MDS 9000 8-port 10-Gbps Fibre Channel over Ethernet (FCoE) module

Cisco MDS 9000 48-port 8-Gbps Advanced Fibre Channel Switching module

Cisco MDS 9000 32-port 8-Gbps Advanced Fibre Channel Switching module

You cannot bring up these modules if these features are already configured. You should completely remove all configurations that include these features before you attempt to bring up these modules. In addition, you cannot configure these features after you bring up these modules.

SNIA Common Information Model

SNIA Common Information Model (CIM or cimserver) commands are no longer supported. CIM is supported in Cisco DCNM-SAN Release 5.2. The SMI-S agent that is installed on the Cisco

DCNM-SAN server allows external application to access fabric and switch profiles as specified in SNIA

CIM. For additional information, see the Cisco DCNM Release Notes, Release 5.2.

IVR Non-NAT Mode

IVR non-NAT mode is not supported in Cisco NX-OS Release 5.2(x). If you have IVR non-NAT mode configured, see the

“Upgrading Guidelines Specific to NX-OS Release 5.2(8c)” section on page 15 for

instructions on how to migrate to IVR NAT mode before upgrading to Cisco NX-OS Release 5.2(8).

Limitations and Restrictions

This section lists the limitations and restrictions. The following limitations are described:

SME Quorum, page 32

OUI Mismatch for SME Tape Targets, page 32

FCIP Performance Drop, page 33

FCoE Module, page 33

IPv6, page 33

User Roles, page 33

Schedule Job Configurations, page 33

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 31

Limitations and Restrictions

Maximum Number of Zones Supported in Interop Mode 4, page 33

InterVSAN Routing, page 34

Java Web Start, page 34

VRRP Availability, page 34

Using a RSA Version 1 Key for SSH Following an Upgrade, page 34

CFS Cannot Distribute All Call Home Information, page 35

Availability of F Port Trunking and F Port Channels, page 35

Reserved VSAN Range and Isolated VSAN Range Guidelines, page 36

Applying Zone Configurations to VSAN 1, page 36

Running Storage Applications on the MSM-18/4, page 36

RSPAN Traffic Not Supported on CTS Ports on 8-Gbps Switching Modules, page 37

I/O Accelerator Feature Limitations, page 37

Support for FCIP Compression Modes, page 37

Saving Copies of the Running Kickstart and System Images, page 37

Configuring Buffer Credits on a Generation 2 or Generation 3 Module, page 37

Features Not Supported on the Cisco MDS 9148 Switch, page 38

PPRC Not Supported with FCIP Write Acceleration, page 38

Configuring a Persistent FCID in an IVR Configuration with Brocade Switches, page 38

SME Quorum

You cannot change the quorum or the SME master node during a master key rekey. If a change occurs during the smart card portion of the operation, the master key rekey operation will fail and must be repeated from the beginning.

OUI Mismatch for SME Tape Targets

If Cisco DCNM does not discover all expected tape targets, check the sme.log to identify an OUI mismatch. Look for a message like the following:

2012.04.09 21:15:50 WARN [SME] skipped target 50:06:0b:00:00:b8:e4:b0 due to explicit type mismatch. Expect: 240 found: 228. If this is an error update your OUI definitions

To correct this issue, manually add the OUI definitions to the server.properties file. The format is as follows:

# 0xhhhhhh vendor_name devicetypes h(host)|d(disk)|t(tape)|s(switch)|g(gateway)|m(cisco mds)

# for example: newOUIs=0x00E069 JNI h|d; 0x000ded Cisco m;\

# 0x006069 Brocade s; newOUIs=

32

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Limitations and Restrictions

FCIP Performance Drop

FCIP performance can drop in a topology where the round-trip time (RTT) delay is configured at 80 ms,

IPsec is enabled, and write acceleration (WA) is not used.

FCoE Module

In Cisco MDS NX-OS Release 5.2(x), you cannot install a FCoE module in a switch that is running

DMM, SME, or IOA.

Link traps for FCoE devices are sent only when a VFC interface flaps.

IPv6

The management port on Cisco MDS switches supports one user-configured IPv6 address, but does not support auto-configuration of an IPv6 address.

User Roles

In SAN-OS Release 3.3(x) and earlier, when a user belongs to a role which has a VSAN policy set to

Deny and the role allows access to a specific set of VSANs (for example, 1 through 10), the user is restricted from performing the configuration, clear, execute, and debug commands which had a VSAN parameter outside this specified set. Beginning with NX-OS Release 4.1(1b), these users are still prevented from performing configuration, clear, execute, and debug commands as before, however, they are allowed to perform show commands for all VSANs. The ability to execute the show command addresses the following:

• In a network environment, users often need to view information in other VSANs even though they do not have permission to modify configurations in those VSANs.

• This behavior makes Cisco MDS 9000 Series switches consistent with other Cisco products, such as Cisco Nexus 7000 Series switches, that exhibit the same behavior for those roles (when they apply to the VLAN policy).

Schedule Job Configurations

As of MDS NX-OS Release 4.1(1b) and later, the scheduler job configurations need to be entered in a single line with a semicolon(;) as the delimiter.

Job configuration files created with SAN-OS Release 3.3(1c) and earlier, are not supported. However, you can edit the job configuration file and add the delimiter to support Cisco NX-OS Release 4.1(3a).

Maximum Number of Zones Supported in Interop Mode 4

In interop mode 4, the maximum number of zones that is supported in an active zone set is 2047, due to limitations in the connected vendor switch.

When IVR is used in interop mode 4, the maximum number of zones supported, including IVR zones, in the active zone set is 2047.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07 33

Limitations and Restrictions

InterVSAN Routing

When using InterVSAN Routing (IVR), it is recommended to enable Cisco Fabric Services (CFS) on all

IVR-enabled switches. Failure to do so may cause mismatched active zone sets if an error occurs during zone set activation.

Java Web Start

When using Java Web Start, we recommend that you do not use an HTML cache or proxy server. You can use the Java Web Start Preferences panel to view or edit the proxy configuration. To do this, launch

Application Manager, either by clicking the desktop icon (Microsoft Windows), or type ./javaws in the

Java Web Start installation directory (Solaris Operating Environment and Linux), and then select Edit>

Preferences.

If you fail to change these settings, you may encounter installation issues regarding a version mismatch.

If this occurs, clear your Java cache and retry.

VRRP Availability

The Virtual Router Redundancy Protocol (VRRP) is not available on the Gigabit Ethernet interfaces on the MSM-18/4 module or module 1 of the MDS 9222i switch, even though it is visible on these modules.

The feature is not implemented in the current release.

Using a RSA Version 1 Key for SSH Following an Upgrade

For security reasons, NX-OS Release 4.2(1b) does not support RSA version 1 keys. As a result, if you upgrade to NX-OS Release 4.2(1b) from an earlier version that did support RSA version 1 keys, and you had configured an RSA version 1 key for SSH, then you will not be able to log in through SSH following the upgrade.

If you have an RSA version 1 key configured for SSH, before upgrading to NX-OS Release 4.1(3a), follow these steps:

Step 1

Step 2

Step 3

Step 4

Disable SSH.

Create RSA version 2 DSA keys.

Enable SSH.

Delete any RSA version 1 keys on any remote SSH clients and replace the version 1 keys with the new version 2 keys from the switch.

Proceed with the upgrade to NX-OS Release 4.2(1b).

34

If you upgrade before disabling SSH and creating RSA version 2 keys, follow these steps:

Step 1

Step 2

Step 3

Open a Telnet session and log in through the console.

Use the no feature ssh command to disable SSH.

Use the ssh key rsa 1024 command to create RSA version 2 keys.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Limitations and Restrictions

Step 4 Use the feature ssh command to enable SSH.

CFS Cannot Distribute All Call Home Information

In MDS NX-OS Release 4.2(1b), CFS cannot distribute the following Call Home commands that can be configured with the destination-profile command:

destination-profile profile_name transport-method

destination-profile profile_name http

The output of the show running-config callhome command shows configured Call Home commands: switch# show running-config callhome

> version 4.1(3)

> callhome

> email-contact [email protected] <mailto:[email protected]>

> phone-contact +14087994089

> streetaddress xyxxyx

> distribute

> destination-profile testProfile

> destination-profile testProfile format XML

> no destination-profile testProfile transport-method email

> destination-profile testProfile transport-method http

> destination-profile testProfile http https://xyz.abc.com

> destination-profile testProfile alert-group all

> transport email smtp-server 64.104.140.134 port 25 use-vrf management

> transport email from [email protected] <mailto:[email protected]>

> enable

> commit

When you attempt to apply these commands in the ASCII configuration, the following commands fail:

> no destination-profile testProfile transport-method email

> destination-profile testProfile transport-method http

> destination-profile testProfile http https://xyz.abc.com

To work around this issue, use these commands after the commit command.

Availability of F Port Trunking and F Port Channels

Trunking F ports and trunking F port channels are not supported on the following MDS 9000 components:

• DS-C9134-K9, Cisco MDS 9134 Multilayer Fabric Switch, if NPIV is enabled and the switch is used as the NPV core switch

• DS-C9124-K9, Cisco MDS 9124 Multilayer Fabric Switch, if NPIV is enabled and the switch is used as the NPV core switch

Trunking F ports, trunking F port channels and regular F port channels are not supported on the following

MDS 9000 components:

DS-X9016, Cisco MDS 9000 2-Gbps16-Port Fibre Channel Switching Module

DS-X9032, Cisco MDS 9000 2-Gbps 32-Port Fibre Channel Switching Module

DS-X9032-14K9, Cisco MDS 9000 14/2-Port Multiprotocol Services Module (MPS-14/2)

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

35

Limitations and Restrictions

For configuration information, refer to the “Configuring Trunking” section in the Cisco MDS 9000

NX-OS Interfaces Configuration Guide.

Reserved VSAN Range and Isolated VSAN Range Guidelines

On an NPV switch with a trunking configuration on any interface, or on a regular switch where the

feature fport_channel_trunk command has been used to enable the Trunking F port channels feature, follow these configuration guidelines for reserved VSANs and the isolated VSAN:

• If trunk mode is on for any of the interfaces or NP port channel is up, the reserved VSANs are 3040 to 4078, and they are not available for user configuration.

• The Exchange Virtual Fabric Protocol (EVFP) isolated VSAN is 4079, and it is not available for user configuration.

The following VSAN IDs are assigned in the Fibre Channel Framing and Signaling (FC-FS) interface standard:

VF_ID Value

00h

001h ... EFFh

F00h ... FEEh

FEFh

FF0h ... FFEh

FFFh

FEFh = 4079

Value Description

Do not use as a Virtual Fabric Identifier.

Available as a Virtual Fabric Identifier.

Reserved.

Control VF-ID (see Fibre Channel Link Services

(FC-LS) and Fibre Channel Switch Fabric

Generation 4 (FC-SW-4) standards).

Vendor specific.

Do not use as a Virtual Fabric Identifier.

Applying Zone Configurations to VSAN 1

In the setup script, you can configure system default values for the default-zone to be permit or deny, and you can configure default values for the zone distribution method and for the zone mode.

These default settings are applied when a new VSAN is created. However, the settings will not take effect on VSAN 1, because it exists prior to running the setup script. Therefore, when you need those settings for VSAN 1, you must explicitly use the following commands:

zone default-zone permit vsan 1

zoneset distribute full vsan 1

zone mode enhanced vsan 1

Running Storage Applications on the MSM-18/4

The Cisco MDS 9000 18/4-Port Multiservice Module (MSM-18/4) does not support multiple, concurrent storage applications. Only one application, such as SME or DMM, can run on the MSM-18/4 at a time.

36

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Limitations and Restrictions

RSPAN Traffic Not Supported on CTS Ports on 8-Gbps Switching Modules

An inter-switch link (ISL) that is enabled for Cisco TrustSec (CTS) encryption must be brought up in non-CTS mode to support remote SPAN (RSPAN) traffic on the following modules:

• DS-X9248-96K9: Cisco MDS 9000 48-Port 8-Gbps Fibre Channel Switching Module

DS-X9224-96K9: Cisco MDS 9000 24-Port 8-Gbps Fibre Channel Switching Module

DS-X9248-48K9: Cisco MDS 9000 4/44-Port Host-Optimized 8-Gbps Fibre Channel Switching

Module

If the ISL link is brought up with CTS enabled, random packet drops of both RSPAN traffic and normal traffic will occur on the receiver port switch.

I/O Accelerator Feature Limitations

IOA does not support the following NX-OS features:

F port trunking

F port channeling

IOA cannot be configured on flows in topologies that have devices with NPV and NPIV enabled.

For example, IOA is not supported in a topology where a host logs in from a NPV edge switch and

IOA is deployed on a NPV core switch for this host.

Support for FCIP Compression Modes

In Cisco NX-OS Release 4.2(1b) and later, FCIP compression mode 1 and compression mode 3 are not supported on the Cisco MSM-18/4 module and on the SSN-16 module.

Saving Copies of the Running Kickstart and System Images

After you upgrade to MDS NX-OS Release 4.2(1b), you are not allowed to delete, rename, move, or overwrite the kickstart and system images that are in the current system bootvar settings on an active or standby MDS Supervisor-2 module on any Cisco MDS 9500 Series switch. This restriction does not apply to the integrated supervisor module on the MDS 9200 and MDS 9100 series switches.

Configuring Buffer Credits on a Generation 2 or Generation 3 Module

When you configure port mode to auto or E on a Generation 2 module, one of the ports will not come up for the following configuration:

Port Mode: auto or E for all of the ports

Rate Mode: dedicated

• Buffer Credits: default value

When you configure port mode to auto or E on a Generation 3 module, one or two of the ports will not come up for the following configuration:

• Port Mode: auto or E for the first half of the ports, the second half of the ports, or for all of the ports

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

37

Limitations and Restrictions

• Rate Mode: dedicated

• Buffer Credits: default value

When you configure port mode to auto or E for all ports in the global buffer pool, you need to reconfigure buffer credits on one or more of the ports. The total number of buffer credits configured for all the ports in the global buffer pool should be reduced by 64.

Features Not Supported on the Cisco MDS 9148 Switch

The Cisco MDS 9148 Multilayer Fabric Switch does not support the following NX-OS features:

• Remote Span

Translative loop support

FCC - no generation, quench reaction only

FC-Redirect

DMM

SME

IOA

• FCoE

In addition, the following features have these limits:

VSANs - 31 maximum

SPAN - 1 session maximum

PPRC Not Supported with FCIP Write Acceleration

IBM Peer to Peer Remote Copy (PPRC) is not supported with FCIP Write Acceleration.

Configuring a Persistent FCID in an IVR Configuration with Brocade Switches

The following information is relevant if you have a fabric that consists of Cisco MDS 9000 switches and

Brocade switches, and the Cisco MDS switches are running either NX-OS Release 4.x or Release 5.x and Brocade is running FOS higher than 6.x. In an IVR configuration, when IVR NAT is enabled on a

Cisco MDS 9000 switch, the device in the native VSAN should be configured with a persistent FCID.

Assuming the FCID is 0xAABBCC, AA should be configured with the virtual IVR domain ID of the

VSAN that contains the ISLs and BB should be configured in the following range:

1 through 64 if the Brocade switch is operating in native interop mode.

1 through 30 if the Brocade switch is operating in McData Fabric mode or McData Open Fabric

Mode.

This configuration ensures that the devices connected to the Cisco MDS 9000 switch can be seen in the name server database on the Brocade switch.

38

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Caveats

Caveats

Severity 3

CSCtr50223

CSCts79593

CSCtt97930

CSCtz92415

CSCud77292

CSCue76534

CSCuh49283

CSCui47352

CSCuj33175

Severity 4

CSCtz40745

CSCuh48617

CSCuj15179

CSCug88985

Severity 5

CSCui40517

Severity 6

CSCud60167

CSCuh13459

CSCue31727

This section lists the open and resolved caveats for this release. Use

Table 17 to determine the status of

a particular caveat. In the table, “O” indicates an open caveat and “R” indicates a resolved caveat.

Table 17 Open Caveats and Resolved Caveats Reference

DDTS Number

NX-OS Software Release (Open or Resolved)

5.2(8b)

NX-OS Software Release (Open or Resolved)

5.2(8c)

Severity 2

CSCtr10877

CSCuf82609

CSCug14122

CSCuh37423

CSCui26277

CSCuj58172

CSCuj74361

O

O

O

O

O

O

O

O

R

O

R

R

R

O

O

O

O

O

O

O

O

O

O

O

O

R

R

R

R

R

O

R

R

O

R

R

R

R

R

R

O

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

39

Caveats

Table 17

DDTS Number

CSCuh27347

CSCug79410

Open Caveats and Resolved Caveats Reference (continued)

NX-OS Software Release (Open or Resolved)

5.2(8b)

O

R

R

NX-OS Software Release (Open or Resolved)

5.2(8c)

Resolved Caveats

• CSCui26277

Symptom: When a leap second adjustment occurs on the Network Time Protocol (NTP) server, multiple symmetrix ports that run Symmetrix Remote Data Facility (SRDF) connected to the

Storage Services Module (SSM) modules experience traffic disruption with the following error:

FCP_CNTR_LAF_C3_TIMEOUT_FRAMES_D

FCP_CNTR_MAC_C3_TIMEOUT_FRAMES_D

Condition: This issue occurs during a normal operation.

Workaround: This issue is resolved.

More Information: The show logging onboard command does not display information about this error.

CSCuj74361

Symptom: The Forwarding Information Base (FIB) process crashes with the following system log message:

%SYSMGR-SLOT4-2-SERVICE_CRASHED: Service "fib" (PID 1846) hasn't caught signal 11

(core will be saved).

Condition: This issue only occurs on Cisco MDS DS-X9248-256K9 and DS-X9232-256K9 modules.

Workaround: This issue is resolved.

CSCuj58172

Symptom: With inter-VSAN routing (IVR) Network Address Translation (NAT) configurations, bringing a port, including the Inter-Switch Link (ISL) ports Up might fail and the port is stuck in

errDisabled state. If the affected port is a member of a port channel, the following error message appears when the show port-channel internal event-history errors command is used:

3) Event:E_DEBUG, length:174, at 820502 usecs after Tue Sep 24 16:56:18 2013

[102] pcm_pcp_ac_process_error(2033): fc1/35 PM did not respond to ACL programming, PCP bringup timed out epp: timeout waiting for response (err_id

0x4092000E) for command 1

The IVR Fibre Channel ID (FCID) rewrite list displays entries in ADD_PROGRESS state when the

show ivr internal fcid-rewrite-list command is used:

11 0x021100 0x283f75 31 0x3744c6 0xcf3f89 0 0

ADD_PROGRESS

11 0x021200 0x283f75 31 0x3734c6 0xcf3f89 0 0

ADD_PROGRESS

11 0x021300 0x283f75 31 0x3744c7 0xcf3f89 0 0

ADD_PROGRESS

40

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

OL-27554-07

Caveats

11 0x021400 0x283f75 31 0x3734c7 0xcf3f89 0 0

ADD_PROGRESS

Condition: This issue occurs during a normal operation.

Workaround: This issue is resolved.

CSCue76534

Symptom: Zone conversion from the legacy zoning to smart zoning by using the zone convert

smart-zoning command might fail without a notice. The zone conversion failure leaves the devices in zones with an FC-4 type of unknown.

This condition can be confirmed with the following command: switch# show zone smart-zoning auto-conv status vsan 1-4093

Vsan: 1

zone name device-zone-1 vsan 1

pwwn 11:11:11:11:11:11:11:01 unknown

pwwn 22:22:22:22:22:22:22:01 unknown

Condition: This issue only occurs when the smart zoning conversion command is used on switches with a single supervisor after an In-Service Software Upgrade (ISSU) from the smart zoning unaware version to smart zoning aware version. The conversion might fail for all devices that you attempt to convert.

Workaround: This issue is resolved.

CSCtz92415

Symptom: The zone server crashes with the following error:

%SYSMGR-2-SERVICE_CRASHED: Service "zone" (PID 2573) hasn't caught signal 6 (core will be saved).

Condition: This occurs during a normal operation.

Workaround: This issue is resolved.

CSCui47352

Symptom: Although the password for TACACS server is entered in the encrypted format, the Cisco

NX-OS software still re-encrypts it.

Condition: This issue occurs when using the TACACS server and the key 7 parameter.

Workaround: This issue is resolved.

CSCts79593

Symptom: The operational status of a virtual storage area network (VSAN) is displayed as Down.

Condition: This issue occurs when one of these conditions is met:

– After using the suspend and no suspend command for a VSAN, which is carried on an E port.

– In the VSAN 1, without any trigger, the F ports associated to the VSAN 1 go Down.

Workaround: This issue is resolved.

CSCtt97930

Symptom: Registered state change notifications (RSCNs) are sent repeatedly to a device using inter-VSAN routing (IVR).

Condition: This issue occurs when IVR is enabled on on the device.

Workaround: This issue is resolved.

CSCuj33175

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

41

Caveats

42

Symptom: An Inter-Switch Link (ISL) that connects two MDS Generation 4 ports does not automatically recover after the link fails or it is shutdown or no shutdown with the following error: fcx/y is down (Link failure or not-connected)

Condition: This issue occurs on DS-X9232-256K9 and DS-X9248-256K9 only when the port is in a fixed speed configuration.

Workaround: This issue is resolved.

CSCud77292

Symptom: The command line interface (CLI) output of the show interface fc command does not increment properly when packets are dropped because of timeouts.

Condition: This issue only occurs only in Cisco MDS DS-X9232-256K9 and DS-X9248-256K9 modules.

Workaround: This issue is resolved.

CSCuh48617

Symptom: After an ungraceful failure of the active supervisor in a Cisco MDS 9509 chassis, traffic to or from an MDS DS-X9232-256K9 and DS-X9248-256K9 module is dropped while the supervisor switchover completes with the following syslog messages:

%CALLHOME-2-EVENT: SUP_FAILURE

%MODULE-4-MOD_WARNING: Module 1 (serial: xxxxxxxxxxx) reported warning due to SAC sync lost in device 145 (device error 0xc910026b)

%SYSTEMHEALTH-4-OHMS_MOD_SNAKE_PATH_FAILURE: Snake Loopback data path failure on module 1.

%SYSTEMHEALTH-4-OHMS_MOD_SNAKE_TEST_ERRORS: Snake Loopback test cannot proceed due to internal errors for module 1.

Ports on other modules might be affected if they send traffic to the DS-X9232-256K9 or

DS-X9248-256K9 modules, and display the following syslog message:

%PORT-5-IF_DOWN_LINK_FAILURE: %$VSAN 2%$ Interface fcx/y is down (Link failure Link

Reset failed nonempty recv queue)

Condition: This issue only occurs in an MDS 9506 or 9509 chassis with DS-X9232-256K9 or

DS-X9248-256K9 modules. This issue is triggered by ungraceful switchovers only; for example, a process failure on the active supervisor causes a High Availability (HA) switchover.

Workaround: This issue is resolved.

CSCuj15179

Symptom: An MDS switch gets reloaded and the show system reset-reason command displays the following error: reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---

1) At 844701 usecs after Thu Aug 29 01:29:45 2013

Reason: Reset Requested by management application

Service:

Version: 5.2(2d)

Condition: This issue occurs after a reset requested by the management application.

Workaround: This issue is resolved.

CSCud60167

Symptom: An In Service Software Upgrade (ISSU) from Cisco MDS NX-OS Release 5.2.x to Cisco

MDS NX-OS Release 6.x by using Cisco Data Center Network Manager (DCNM) fails with the following error:

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Caveats

Failure copyDeviceBusy

Condition: This issue occurs during a normal operation.

Workaround: This issue is resolved.

CSCuh13459

Symptom: An enhancement is required for the show logging onboard command so that it displays clearly denoted CLI output.

Workaround: This issue is resolved.

CSCug88985

Symptom: A Cisco MDS switch allocates an area Fibre Channel ID (FCID) instead of a single FCID to a device for a fabric login (FLOGI).

Condition: This issue occurs when one of the conditions is true:

– The MDS switch is configured with the following commands:

no fcdomain fcid persistent vsan vsan_number

fcinterop fcid-allocation flat

The host has a port WWN (PWWN) with an organizationally unique identifier (OUI), which is in the default area allocation list. The list of OUIs that get an AREA FCID assigned by default can be retrieved by using the command show fcid-allocation area command.

The MDS running Cisco NX-OS 5.2(8b) or lower version.

Workaround: This issue is resolved.

CSCui40517

Symptom: A Cisco MDS Generation 4 module, DS-X9232-256K9 displays speed as Unknown even though the port configuration is Up.

Condition: This issue occurs because of a sync loss.

Workaround: This issue is resolved.

CSCuh27347

Symptom: During an In-Service Software Upgrade (ISSU) or In-Service Software Downgrade

(ISSD), ports that are administratively Up and also in the not-connected state get reinitialized.

Condition: This issue occurs in all Cisco MDS dual-supervisor switches during a normal operation.

Workaround: This issue is resolved.

CSCug79410

Symptom: When all modules are logically removed from the system excluding the active supervisor, the modules might not be detected when they are added again. If the modules are detected, the standby supervisor does not reach the High Availability (HA) status.

Condition: This issue only occurs after a hardware failure with the PM bus on the active supervisor.

Workaround: This issue is resolved.

Open Caveats

• CSCtr10877

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

43

Caveats

Symptom: Some Fibre Channel Routing (FCR) peers might get out of sync with the master switch

FCR peer after an Inter-Switch Link (ISL) flap. This might cause the intelligent application flows not to come online or to get deleted.

Workaround: This issue might occur when using any of the following FCR intelligent applications:

– Storage Media Encryption (SME)

I/O Acceleration (IOA)

Data Mobility Manager (DMM)

Workaround: Check the intelligent applications to verify whether any flows are deleted on the problematic switch. If they did, you must recreate flows again through the application CLI or the

Cisco Fabric Manager or Cisco Data Center Network Manager (DCNM)-SAN interface.

Enter the following supervisor CLI commands on the problematic FCR switch that triggers it to resync its configuration with the rest of the fabric.

For a single switch, use the following command: test fc-redirect config sync-with-fabric

If more than one peer is affected by this issue, use the following command:

• test fc-redirect config sync-with-fabric all-peers

CSCtr50223

Symptom: On the MDS 9513 switch, when an MSM-18/4 module boots up, it sends a request to the supervisor module to mount the modflash on the MSM-18/4 module. If there is a timeout or error in response, the following syslog message displays:

2011 Jul 14 01:18:13 sw-dc5-br2-12 %LC_MNT_MGR-SLOT3-2-LC_MNT_MGR_ERROR: SUP mount failed. MTS receive timedout

2011 Jul 14 01:19:06 sw-dc5-br2-12 %PROC_MGR-SLOT3-2-ERR_MSG: ERROR: PID 1144

(lc_mnt_mgr) exited abnormally, exit status (0xa)

2011 Jul 14 01:19:06 sw-dc5-br2-12 %MODULE-2-MOD_MINORSWFAIL: Module 3 (serial:

JAE1141ZB43) reported a failure in service lc_mnt_mgr

This issue might be seen when the supervisor module is unusually busy and cannot process the mount request from the MSM-18/4 module, or the actual mount command on the supervisor takes a long time.

Workaround: Reload the MSM-18/4 module in the same slot/module where the modflash mount failed. A request will be sent to the supervisor to mount the modflash.

CSCty82821

Symptom: After creating an SME cluster, adding disks to a disk group, changing some disk states, and starting the master key rekey, the key creation date is invalid.

Workaround: None.

44

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

OL-27554-07

Caveats

CSCtz40745

Symptom: A “VSAN down” trap is sent for VSAN 4094 when a trunk port goes down even though the VSAN is not configured on the trunk.

This symptom might be seen only when a link down occurs on an E, TE, or TF port.

Workaround: Ignore the trap.

CSCty47599

Symptom: The master key share fails if crypto cluster configuration changes during process.

Workaround: None.

CSCuf82609

Symptom: After an In-Service Software Upgrade (ISSU) on the Cisco MDS 9222i switch, Cisco

Fabric Services (CFS) merge is initiated.

Condition: This issue only occurs on fabric switches (non-director class switches) that are part of a very large fabric.

Workaround: None.

More information: This is a known issue with the CompactFlash card.

CSCug67068

Symptom: On Cisco MDS 9148 and MDS 9134 switches, an attempt to overwrite a file fails with the following error:

Permission denied

Condition: This issue occurs if a previous attempt to copy to a file with the same name failed.

Workaround: None.

CSCuf82609

Symptom: After changing the device alias configuration, the I/O Accelerator (IOA) flows remain unchanged until the reactivation of the zone set.

Condition: This situation occurs during a device-alias add, delete, or rename operation.

Workaround: None.

CSCug14122

Symptom: The interface manager (ifmgr) might crash during an In Service Software Upgrade

(ISSU).

Condition: This situation occurs when you perform a downgrade to Cisco NX-OS 5.2(8c) from a higher version.

Workaround: This issue is resolved.

CSCuh37423

Symptom: After changing the device alias configuration, the I/O Accelerator (IOA) flows remain unchanged until the reactivation of the zone set.

Condition: This situation occurs during a device-alias add, delete, or rename operation.

Workaround: None.

CSCuh49283

Symptom: One of the following symptoms are observed:

– A zone member goes offline.

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

45

Related Documentation

– A Registered State Change Notification (RSCN) is not sent to zoned members.

The device-mapping entry port world wide name (pWWN) associated to a device alias is not displayed in the Dynamic Port VSAN Membership (DPVM) database.

The show running-configuration ivr command does not display the changes when a device alias member in an Inter-VSAN routing zone (IVR zone) is renamed.

The port world wide name (pWWN) associated with the device alias is found dissociated in the port security database.

A device alias member is not found in the port security database.

Condition: This situation occurs when all or one of the conditions is met:

– A user attempts to perform a device-alias operation in batch, such as:

• Renaming an offline device alias to an existing online device alias or vice versa.

• Multiple commands are entered using the same device-alias name before a commit.

A device alias was renamed.

A device alias was deleted and an existing device alias is renamed to the deleted device alias in the same commit.

A device alias, which is not configured, resides in the DPVM database and an online device is renamed to the former.

The IVR distribute option is enabled and the device alias is in enhanced mode, and the changes in a device alias is not updated to the IVR running configuration.

Workaround: Add the offline member to the device alias database, revert to the previous name if you have renamed a device alias, and flap the ports that are connected to the affected zone member.

CSCuh57761

Symptom: Multiple port security members that are mapped to a switch WWN (sWWN) logging point are not fully distributed to the peer switches. The following error appears after an Cisco

In-Service Software Downgrade (ISSD), followed by entering the port-security commit command:

Internal CLI error: Timer expired

Condition: This situation occurs after an ISSD from Cisco MDS NX-OS Release 5.2(8b) to 5.2.(1).

After creating and committing port-security entries that map multiple port security members to the same sWWN, all entries are not distributed to the peer switches.

Workaround: None.

CSCue31727

Symptom: A user with the priv-14 role does not inherit rules from the priv-0 through priv-13 roles.

Condition: This situation occurs during a normal operation.

Workaround: Create users with roles from priv-0 to priv-13 and log in, or log in to the switch using

AAA authentication where users with certain user levels are identified.

Related Documentation

The documentation set for NX-OS for the Cisco MDS 9000 Family includes the following documents.

To find a document online, access the following web site: http://www.cisco.com/en/US/products/ps5989/tsd_products_support_series_home.html

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

46 OL-27554-07

Related Documentation

The documentation set for Cisco Fabric Manager appears in the Cisco Fabric Manager Release Notes

for Release 4.2(1), which is available from the following website: http://www.cisco.com/en/US/products/ps10495/prod_release_notes_list.html

Release Notes

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Releases

Cisco MDS 9000 Family Release Notes for MDS SAN-OS Releases

Cisco MDS 9000 Family Release Notes for Storage Services Interface Images

Cisco MDS 9000 Family Release Notes for Cisco MDS 9000 EPLD Images

Regulatory Compliance and Safety Information

• Regulatory Compliance and Safety Information for the Cisco MDS 9000 Family

Compatibility Information

Cisco Data Center Interoperability Support Matrix

Cisco MDS 9000 NX-OS Hardware and Software Compatibility Information and Feature Lists

Cisco MDS NX-OS Release Compatibility Matrix for Storage Service Interface Images

Cisco MDS 9000 Family Switch-to-Switch Interoperability Configuration Guide

Cisco MDS NX-OS Release Compatibility Matrix for IBM SAN Volume Controller Software for

Cisco MDS 9000

Cisco MDS SAN-OS Release Compatibility Matrix for VERITAS Storage Foundation for Networks

Software

Hardware Installation

Cisco MDS 9500 Series Hardware Installation Guide

Cisco MDS 9500 Series Supervisor-2A Tech Note

Cisco MDS 9200 Series Hardware Installation Guide

Cisco MDS 9100 Series Hardware Installation Guide

Cisco MDS 9124 and Cisco MDS 9134 Multilayer Fabric Switch Quick Start Guide

Software Installation and Upgrade

Cisco MDS 9000 NX-OS Software Upgrade and Downgrade Guide

Cisco MDS 9000 Family Storage Services Interface Image Install and Upgrade Guide

Cisco MDS 9000 Family Storage Services Module Software Installation and Upgrade Guide

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

47

Related Documentation

Cisco NX-OS Configuration Guides

Cisco MDS 9000 Family NX-OS Licensing Guide

Cisco MDS 9000 Family NX-OS Fundamentals Configuration Guide

Cisco MDS 9000 Family NX-OS System Management Configuration Guide

Cisco MDS 9000 Family NX-OS Interfaces Configuration Guide

Cisco MDS 9000 Family NX-OS Fabric Configuration Guide

Cisco MDS 9000 Family NX-OS Quality of Service Configuration Guide

Cisco MDS 9000 Family NX-OS Security Configuration Guide

Cisco MDS 9000 Family NX-OS IP Services Configuration Guide

Cisco MDS 9000 Family NX-OS Intelligent Storage Services Configuration Guide

Cisco MDS 9000 Family NX-OS High Availability and Redundancy Configuration Guide

Cisco MDS 9000 Family NX-OS Inter-VSAN Routing Configuration Guide

Command-Line Interface

• Cisco MDS 9000 Family Command Reference

Intelligent Storage Networking Services Configuration Guides

Cisco MDS 9000 I/O Acceleration Configuration Guide

Cisco MDS 9000 Family SANTap Deployment Guide

Cisco MDS 9000 Family Data Mobility Manager Configuration Guide

Cisco MDS 9000 Family Storage Media Encryption Configuration Guide

Cisco MDS 9000 Family Secure Erase Configuration Guide

Cisco MDS 9000 Family Cookbook for Cisco MDS SAN-OS

Troubleshooting and Reference

Cisco NX-OS System Messages Reference

Cisco MDS 9000 Family NX-OS Troubleshooting Guide

Cisco MDS 9000 Family NX-OS MIB Quick Reference

Cisco MDS 9000 Family NX-OS SMI-S Programming Reference

48

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

Obtaining Documentation and Submitting a Service Request

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

This document is to be used in conjunction with the documents listed in the

“Related Documentation” section.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of

Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

© 2013 Cisco Systems, Inc. All rights reserved.

OL-27554-07

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

49

Obtaining Documentation and Submitting a Service Request

50

Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.2(8c)

OL-27554-07

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement