SL-65DVB/65DV2 V1.0 USER MANUAL

SL-65DVB/65DV2 V1.0 USER MANUAL
R
SL-65DVB/65DV2 V1.0
USER MANUAL
USER NOTICE
T
Product Model
Manual Revision
Release Date
: SL-65DVB/65DV2
: V1.0
: November 2000
his Users Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the
motherboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for printing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identification purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respective companies.
Soltek computer inc. Provides this manual “As is “ without warranty of any kind, either express or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness
for a particular purpose. In no event shall Soltek computer inc. Be
liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or consequential damages of any kind, even if Soltek computer inc. Has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 2000 Soltek Computer Inc. All Rights Reserved.
• Intel, Celeron, Pentium II, Pentium III are trademarks of Intel Corporation.
• Intel 82815 Graphic Memory Controller Hub(GMCH), 82801 I/O Controller Hub(ICH) are trademarks of Intel Corporation.
• VIA Cyrix III is trademark of VIA Corporation.
• Norton AntiVirus, Norton Ghost are trademarks of Symantec Corporation.
SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address
Telephone
Fax
E-mail
Web site
: 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chin, TaipeiHsien, Taiwan, R.O.C.
: 886-2-2642-9060
: 886-2-2642-9065
: [email protected]
: http://www.soltek.com.tw
SOLTEK KOREA INC.
Address
Telephone
Fax
E-mail
: 1002, Chungjin Bldg. 53-5 Wonhyo-Ro, 3-Ka,
Yongsan-Ku Seoul 140-113, Korea
: 82-2-32717400
: 82-2-32717405
: [email protected]
MOKA HOLDING B.V.
Address
Telephone
Fax
E-mail
: De Run 4428 5503 LR Veldhoven, the Netherlands
: 31-402-556150
: 31-402-546006
: [email protected]
SOUL TECHNOLOGY EUROPE B.V.
Address
Telephone
Fax
E-mail
Web site
: Sydneystraat 52-54 3047 BP Rotterdam, the Netherlands
: 31-10-2457492
: 31-10-2457493
: [email protected]
: http://www.soultech-europe.com
65DVB/65DV2
CONTENT
CHAPTER 1
INTRODUCTION ........................................................................... 6
1-1 ITEM LIST CHECKUP ............................................................................ 6
1-2 CPU ........................................................................................................ 6
1-3 CHIPSET ................................................................................................ 6
1-4 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER ................ 6
1-5 FULL FEATURED ACCELERATED GRAPHICS PORT (AGP)
CONTROLLER ....................................................................................... 7
1-6 MULTI-I/O FUNCTION ........................................................................... 7
1-7 EXTENSION SLOTS .............................................................................. 7
1-8 BIOS ....................................................................................................... 8
1-9 SOUND CONTROLLER ......................................................................... 8
1-10 POWER MANAGEMENT ..................................................................... 8
1-11 FROM FACTOR .................................................................................... 8
1-12 HARDWARE MONITORING ................................................................ 8
1-13.1 MOTHERBOARD LAYOUT --- 65DVB .............................................. 9
1-13.2 MOTHERBOARD LAYOUT --- 65DV2 ............................................ 10
1-14 CHIPSET SYSTEM BLOCK DIAGRAM ............................................. 11
1-15 MOTHERBOARD SPECIFICATION TABLE OF ................................. 12
65DVB & 65DV2 ................................................................................. 12
CHAPTER 2
HARDWARE SETUP ................................................................... 14
2-1 CPU INSTALLATION ............................................................................ 14
2-2 MEMORY INSTALLATION ................................................................... 16
2-3 HDD / FDD INSTALLATION ................................................................. 17
2-4 BUS RATIO SELECT ........................................................................... 18
2-4.1 BUS CLOCK SELECT ....................................................................... 18
2-5 JUMPER DEFINITION ......................................................................... 19
2-5.1 ONBOARD FAN CONNECTOR (FAN1/FAN2) .................................. 19
2-5.2 USB PORT SELECT-1 (JP3/JP4) ..................................................... 19
2-5.3 ONBOARD AC97 CODEC SELECT (JP5/JP9) ................................. 20
2-5.4 USB PORT SELECT-2 (JP6/JP7) ..................................................... 20
2-5.5 POWER LOST RESUME (JP8) ......................................................... 21
2-5.6 CD-ROM AUDIO CONNECTOR (CD_IN1/CD_IN2) ......................... 21
2-5.7 CLEAR CMOS DATA (JBAT1) .......................................................... 21
4
65DVB/65DV2
2-5.8 WAKE ON LAN FUNCTION (WOL1) ................................................ 21
2-5.9 THERMAL SENSOR CONNECTOR (RT2) ....................................... 23
2-6 CONNECTORS .................................................................................... 23
2-6.1 J2J3 ................................................................................................... 23
2-6.2 CHASSIS PANEL CONNECTOR ...................................................... 26
2-6.3 ATX POWER SUPPLY CONNECTOR .............................................. 26
2-6.4 AUDIO MODEM RISER SLOT (AMR) ............................................... 27
2-6.5 PS/2 MOUSE AND PS/2 KEYBOARD .............................................. 28
2-6.6 IRQ DESCRIPTION .......................................................................... 28
CHAPTER 3
SOFTWARE SETUP .................................................................... 30
3-1 ABOUT SOLTEK SUPPORT CD .......................................................... 30
3-2 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ................... 30
3-3 AC’97 AUDIO CODEC INSTALLATION ................................................ 34
3-4 HARDWARE MONITOR INSTALLATION ............................................. 35
CHAPTER 4
BIOS SETUP ............................................................................... 36
4-1 INTRODUCE THE BIOS ...................................................................... 36
4-2 WHAT IS BIOS SETUP ........................................................................ 36
4-3 HOW TO RUN BIOS SETUP ............................................................... 36
4-4 WHAT IS CMOS ................................................................................... 37
4-5 WHAT IS POST .................................................................................... 37
4-6 BIOS UPGRADE .................................................................................. 37
4-6.1 BEFORE UPGRADE BIOS ............................................................... 37
4-6.2 UPGRADE PROCESS ...................................................................... 38
4-7 CMOS SETUP UTILITY ....................................................................... 41
4-8 STANDARD CMOS SETUP ................................................................. 42
4-9 ADVANCED BIOS FEATURES ............................................................ 45
4-10 ADVANCED CHIPSET FEATURES ................................................... 50
4-11 INTEGRATED PERIPHERALS ........................................................... 55
4-12 POWER MANAGEMENT SETUP ...................................................... 59
4-13 PNP / PCI CONFIGURATION ............................................................ 65
4-14 PC HEALTH STATUS ......................................................................... 68
4-15 FREQUENCY/VOLTAGE CONTROL ................................................. 69
4-16 LOAD OPTIMIZED DEFAULTS .......................................................... 71
4-17 SET SUPERVISOR / USER PASSWORD ......................................... 71
4-18 SAVE & EXIT SETUP ......................................................................... 72
4-19 EXIT WITHOUT SAVING ................................................................... 72
5
65DVB/65DV2
CHAPTER 1
INTRODUCTION
1-1 ITEM LIST CHECKUP
• Motherboard
• Support CD
• User’s Manual
• Bundle Bonus Pack CD
• Bundle Bonus Pack Manual
• Temperature Sensor Cable
• ATA 66/100 IDE Cable
• FDD Cable
1-2 CPU
• Supports Intel® FC-PGA Pentium !!!TM up to 1GHz or above.
• Supports Intel® FC-PGA 370 Celeron & PGA 370 Celeron up to 766MHz
or above.
• Supports VIA Cyrix !!! up to 600MHz.
• Supports CPU voltage Auto-Detect circuit.
1-3 CHIPSET
• North Bridge - VIA VT82C693A APOLLO PRO-PLUS.
• South Bridge - VIA VT82C686A (for 65DVB only)
VIA VT82C686B (for 65DV2 only)
1-4 ADVANCED HIGH-PERFORMANCE DRAM
CONTROLLER
• Supports FP, SDRAM, VCM memory types up to 3 DIMMS.
• 64-bit data width and 3.3V DRAM interface.
• Supports up to 768MB memory space.
• Different DRAM types may be used in mixed combinations.
• PCI-2.2 compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs .
• DRAM interface synchronous with host CPU (66/100/133 MHz) or AGP
(66MHz) for most flexible configuration.
• DRAM interface may be faster than CPU by 33MHz to allow use of PC100
6
65DVB/65DV2
memory modules with 66MHz Celeron or use of PC133 with 100MHz
Pentium III.
• DRAM interface may be slower than CPU by 33 MHz to allow use of older
memory modules with newer CPUs (e.g., PC66 memory modules with
100 MHz Pentium III).
1-5 FULL FEATURED ACCELERATED GRAPHICS PORT
(AGP) CONTROLLER
• AGP v2.0 compliant
• Supports Sideband Addressing (SBA) mode (non-multiplexed address/
data)
• Supports 133MHz 2x mode for AD and SBA signaling
• Pipelined split-transaction long-burst transfers up to 533 MB/sec
1-6 MULTI-I/O FUNCTION
• Two Ultra DMA-33 / 66 Master Mode PCI EIDE ports (for 65DVB only).
• Two Ultra DMA-33 / 66 / 100 Master Mode PCI EIDE ports (for 65DV2
only).
• Two UART’s for Complete Serial Ports.
• One dedicated IR connector:
Third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector:
Standard mode, ECP and EPP support.
• Floppy Disk connector:
Two FDDs with drive swap support .
• Universal Serial Bus connector:
--- USB v1.1 and Intel Universal HCI v1.1 compatible.
--- Provides 2 build-in USB ports (another 2 internal USB ports for extensible
purpose require an optional USB connect cable).
• PS/2 Keyboard connector.
• PS/2 Mouse connector.
1-7 EXTENSION SLOTS
• Five PCI bus Mater slots.
• One ISA slot.
• One AMR slot.
7
65DVB/65DV2
• One AGP 4x mode slot.
• Three DIMM slots.
1-8 BIOS
• Award BIOS Version 6.0.
• Supports Plug & Play V1.0.
• FLASH MEMORY for easy upgrade.
• Supports BIOS writing protection.
• Year 2000 compliant.
1-9 SOUND CONTROLLER
• Sound Blaster Pro Hardware and Direct Sound Ready AC’97 Digital
Audio Controller with Codec onboard.
1-10 POWER MANAGEMENT
• ACPI 1.0 compliant (Advanced Configuration and Power Interface).
• APM V1.2 compliant (Legacy power management).
• System event monitoring with two event classes.
• Supports PS/2 Keyboard & Mouse power on.
• Supports Wake On LAN (WOL) & Wake On Modem.
• Supports real time clock (RTC) with date alarm, month alarm, and century
field.
1-11 FROM FACTOR
• ATX from factor, 4 layers PCB.
• Motherboard size 19.0cm X 30.5cm.
1-12 HARDWARE MONITORING
• Programmable control, status, monitor and alarm for flexible desktop
management (software included).
• Five-positive voltage.
• Two-temperature monitoring.
• Three Fan-speed monitoring.
8
65DVB/65DV2
1-13.1 MOTHERBOARD LAYOUT --- 65DVB
DIMM3
DIMM2
DIMM1
ATX POWER
1
3
4
31
3
3
JP5
AGP 2X
IDE1
VIA
VT82C
693A
SW1
IDE2
DIP
ON
SOCKET 370
1
USB2
16
JP11
AMR
CD_IN2 JP3 1
JP4 1
CD_IN1
1
RT1
Clock
Generator
FDC1
1
FAN1
1 2 3 4 5 6
MIC
LINE
IN
GAME/MIDI PORT
LINE
OUT
COM2
COM1
LPT1
upper
upper
PS/2
USB0
MOUSE
lower
lower
USB1
PS/2
K/B
• Default Setting: Intel Celeron 300A/66 MHz
4
JP6 1
JP7 1
3
3
PCI 1
Li
Battery
3
AC'97
Codec
3
1
JBAT1
SUSLED
PWR/LED
IR
RST
PCI 5
SPK
ISA
HD/LED
FLASH BIOS
3
1
JWOL1
PCI 4
VIA
VT82C
686A
PWR SUSPEND
RT2
PCI 3
JP8
FAN2
JP9
1
PCI 2
1 1
J2 J3
Using non-compliant memory with higher bus clock (over clocking) may severely
compromise the integrity of system.
9
65DVB/65DV2
1-13.2 MOTHERBOARD LAYOUT --- 65DV2
DIMM3
DIMM2
DIMM1
ATX POWER
1
3
AMR
31
3
3
JP5
AGP 2X
IDE1
VIA
VT82C
693A
SW1
IDE2
DIP
ON
SOCKET 370
1
USB2
16
JP11
4
CD_IN2 JP3 1
JP4 1
CD_IN1
1
RT1
Clock
Generator
FDC1
1
FAN1
1 2 3 4 5 6
MIC
LINE
IN
GAME/MIDI PORT
LINE
OUT
COM2
COM1
LPT1
upper
upper
PS/2
USB0
MOUSE
lower
lower
USB1
PS/2
K/B
• Default Setting: Intel Celeron 300A/66 MHz
4
JP6 1
JP7 1
3
3
PCI 1
Li
Battery
3
AC'97
Codec
3
1
PWR/LED
SUSLED
JBAT1
IR
RST
PCI 5
SPK
ISA
HD/LED
FLASH BIOS
3
1
JWOL1
PCI 4
VIA
VT82C
686B
PWR SUSPEND
RT2
PCI 3
JP8
FAN2
JP9
1
PCI 2
1 1
J2 J3
Using non-compliant memory with higher bus clock (over clocking) may severely
compromise the integrity of system.
10
65DVB/65DV2
1-14 CHIPSET SYSTEM BLOCK DIAGRAM
Socket 370
CPU
AGP Slot or
3D Graphics
Controller
VIA
VT82C
693A
Main
Memory
(DRAM)
PCI5
PCI4
PCI3
Keyboard
& Mouse
VIA
VT82C
686A/
686B
AC97 Codec
USBx4
ATA 33/66 or
ATA 33/66/100
PM Control ,
GPIO , Reset
BIOS
ROM
ISA1
Super IO
IDE x 2
Serial Port x 2
Infrared Port x 1
Parallel Port x 1
FDD x1
PCI2
PCI1
Hardware
Monitoring
Figure 1-11. VIA VT693A System Block Diagram Using the
VT82C686A or VT82C686B South Bridge
11
65DVB/65DV2
1-15 MOTHERBOARD SPECIFICATION TABLE OF
65DVB & 65DV2
Model
North bridge
Sorth bridge
Memory
VIA VT82C693A APOLLO PRO-PLUS
VIA686A
VIA686B
Supports PC133 and PC100 FP, SDRAM and Virtual Channel
Memory (VCM) up to 768MB
3 DIMM Slots
AGP Interface
AGP Pro 2X Mode
Audio
Build-in AC97 codec
IDE
2 x Ultra 33/66
IDE ports
2 x Ultra33/66/100
IDE ports
I/O
4 x USB ports, 1 x FDD port, 2 x COM ports,
1 x LPT port, 1 x IrDA, PS/2 Mouse, PS/1 K/B
PCI slot
5 x PCI Master Slots
ISA slot
1 x ISA slot
Hardware
Monitoring
yes
BIOS writing
Protection
yes
Remark
12
65DV2
65DVB
65DVB/65DV2
ATTENTION !!!
1. Please refer to your processor installation or other
documentation attached with your CPU for detailed
installing instruction.
2. Installing a heat sink and cooling fan is necessary for
proper heat dissipation from your CPU. Uncorrected
installation may result in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct specification both of CPU CLOCK and RATIO. Uncorrected
setting may cause damage to your CPU.
13
65DVB/65DV2
CHAPTER 2
HARDWARE SETUP
2-1 CPU INSTALLATION
Warning!!!
Never run the processor without the heat sink properly and firmly attached
PERMANENT DAMAGE WILL RESULT.
1. Pull the lever sidways away from the socket, and then raise the lever up
to a 90-degree angle.
70
3
ET
CK
SO
2. Take note of the red circle as below picture. When insert the CPU into
socket, you can find out there is a definite pin orientation for CPU and
socket.
370
T
E
CK
SO
14
65DVB/65DV2
3. Make sure that the CPU positions in the socket tightly, and then put the
lever down to complete the CPU installation.
SO
C
T
KE
370
15
65DVB/65DV2
2-2 MEMORY INSTALLATION
WARING !!!
• Make sure that you unplug your power supply when adding or remoning
memory modules or other system components, failure to do so may cause
severe damage to both your motherboard and expansion cards.
• Be careful when inserting or removing DIMM, fouceing a DIMM in or out of
a socket can be damaged the memory module or the socket. Some of DIMMs
contain EDO or FPM DRAM that accept only 5V power. These DIMM types
are incompliant with the motherboard, the M/B only supports 3.3V true
SDRAM DIMMs
Installing DIMM:
• Make sure you have the correct memory module type for your motherboard.
• Insert the mdule(s) as shown, DIMMs have 168-pins and two notches that
will match with the onboard DIMM socket, memory modules are installed by
inserting them straight into the slot until they “click” into place. They only fit
in one direction so do not force them into place.
168-Pin DIMM Notch Key Definitions(3.3V)
DRAM Key Position
Unbuffered
Voltage Key Position
3.3V
Removing:
• Press the holding clips on both sides of socket out ward to release the
DIMM, Gintly pull the DIMM out of the socket.
16
65DVB/65DV2
2-3 HDD / FDD INSTALLATION
DIMM3
DIMM2
DIMM1
16
ATX POWER
1
3
AMR
31
3
3
JP5
AGP 2X
IDE1
VIA
VT82C
693A
SW1
IDE2
DIP
ON
SOCKET 370
USB2
1
Hard Disk Drive Connector:
Orient the red markings on
the IDE ribbon cable to Pin1.
JP11
4
CD_IN2 JP3 1
JP4 1
CD_IN1
1
RT1
Clock
Generator
FDC1
1
FAN1
1 2 3 4 5 6
MIC
LINE
IN
GAME/MIDI PORT
LINE
OUT
COM2
COM1
LPT1
upper
upper
PS/2
USB0
MOUSE
lower
lower
USB1
PS/2
K/B
• To install HDD (Hard Disk Drive), you may connect the cable’s blue
connector to the motherboard’s primary (IDE1) or secondary IDE
connector, and then connect the gray connector to your slave device and the black connector to your master device.If you install two
hard disks , you must configure the second drive to Slave mode by
setting its jumper accordingly.Please refer to your hard disk documentation for the jumper settings.
• To install FDD (Floppy Disk Drive), you may connect the single end
to the board , and connect two plugs on the other end to the floopy
drives.
4
JP6 1
JP7 1
3
3
PCI 1
Li
Battery
3
AC'97
Codec
Floppy Disk Drive Connector:
Orient the red markings on
the floppy ribbon cable to
Pin1.
3
1
JBAT1
SUSLED
PWR/LED
IR
RST
PCI 5
SPK
ISA
HD/LED
FLASH BIOS
1
3
JWOL1
PCI 4
VIA
VT82C
686B
PWR SUSPEND
RT2
PCI 3
JP8
FAN2
JP9
1
PCI 2
1 1
J2 J3
17
65DVB/65DV2
2-4 BUS RATIO SELECT
• Normally, the Bus Ratio (Frenquency Multiple) of your processor is locked
by processor’s Vendor,setting of the CPU Bus Ratio will have no effect.
• Bus Ratio exceed 8.0X, user can not change all values from the ratio will
be detected by BIOS automatically.
• The Bus Ratio Setting is available on unlocked processors only.
SW1 DIP1 ~ DIP4 SETTING
1 2 3 4 5 6
OFF
OFF
OFF
OFF
OFF
6.5x
ON
ON
ON
ON
ON
ON
ON
ON
1 2 3 4 5 6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
7.5x
ON
ON
ON
ON
ON
ON
1 2 3 4 5 6
ON
ON
ON
ON
OFF
1 2 3 4 5 6
1 2 3 4 5 6
OFF
OFF
OFF
8.0x
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
5.5x
1 2 3 4 5 6
7.0x
ON
ON
ON
ON
ON
ON
1 2 3 4 5 6
1 2 3 4 5 6
6.0x
OFF
OFF
OFF
OFF
ON
ON
ON
4.5x
1 2 3 4 5 6
5.0x
ON
ON
ON
ON
ON
ON
4.0x
OFF
1 2 3 4 5 6
ON
OFF
OFF
OFF
3.5x
ON
ON
ON
ON
OFF
3.0x
ON
ON
ON
ON
1 2 3 4 5 6
2-4.1 BUS CLOCK SELECT
• Over clocking is not recommanded, your system may work unstable.
SW1 DIP5 ~ DIP6
JP11: FSB SELECT
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
66/100/133MHz
Auto Select
(default)
1
3
123456
ON
ON
ON
ON
ON
1
OFF
OFF
OFF
OFF
OFF
OFF
100MHz
3
123456
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
133MHz
123456
18
1
3
65DVB/65DV2
2-5 JUMPER DEFINITION
• The figure below shows the location of the motherboard’s jumper blocks.
CAUTION
• Do not move the jumper with the power on. Always turn off the power and unplug
the power cord from the computer before changing the jumper. Otherwise, the
motherboard could be damaged.
2-5.1 ONBOARD FAN CONNECTOR (FAN1/FAN2)
FAN1 / FAN2: ONBOARD FAN CONNECTOR (12V)
CPU FAN
FAN1
SYSTEM FAN
FAN2
Those connectors support processor/system cooling fan with +12V. Those support
three pin head connector. When connecting the wire to FAN connectors, user should
give attention that the red wire is the positive and should be connected to the
+12V, the black wire is Ground and should be connected to GND. If your
motherboard has Hardware Monitor chipset on-board, you must use a specially
designed fan with speed sensor to take advantage of this function.
For fans with fan speed sensor, every rotation of the fan will send out 2 pulses.
System Hardware Monitor will count and report the fan rotation speed.
GND
+12V
SENSOR
NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN supports the FAN control. You can install PC Alert utility.
This will automatically control the CPU FAN speed according to the
actual CPU temperature.
2-5.2 USB PORT SELECT-1 (JP3/JP4)
JP3/JP4: USB PORT SELECT (1)
Redirect USB port 3 to USB 2
connector (default)
JP3
JP4
Redirect USB port 3 to AMR
JP3
JP4
1
3
1
3
1
3
1
3
19
65DVB/65DV2
2-5.3 ONBOARD AC97 CODEC SELECT (JP5/JP9)
JP5/JP9: ONBOARD AC'97 CODEC SELECT
Disabled
JP5
1
3
3
JP9
1
Enabled (default)
JP5
1
3
3
JP9
1
2-5.4 USB PORT SELECT-2 (JP6/JP7)
JP6/JP7: USB PORT SELECT (2)
Redirect USB port 2 to USB 2
connector (default)
Redirect USB port 2 to AGP
JP6
JP7
JP6
JP7
1
3
1
3
1
3
1
3
2-5.5 POWER LOST RESUME (JP8)
JP8: POWER LOST RESUME
3
Normal (default)
JP8
1
3
Enabled
JP8
1
NOTE: This jumper allows user to use the switch of ATX power supply
to control ON/OFF switch directly instead of using the power
switch on the motherboard.
2-5.6 CD-ROM AUDIO CONNECTOR (CD_IN1/CD_IN2)
CD_IN1/CD_IN2: CD-ROM AUDIO CONNECTOR
PIN NO.
PIN 1
PIN 2
PIN 3
PIN 4
20
CD_IN1
GND
Left Channel
GND
Right Channel
CD_IN2
Left Channel
GND
GND
Right Channel
65DVB/65DV2
2-5.7 CLEAR CMOS DATA (JBAT1)
JBAT1: CLEAR CMOS DATA
Clear CMOS Data
JBAT1
Retain Data (default)
JBAT1
1
3
1
3
A battery must be used to retain the motherboard configuration in
CMOS RAM.
NOTE : You can clear CMOS by shorting 2-3 pin when the system is
POWER OFF. Then, return to 1-2 pin position (default). It may
damage the motherboard if clearing the CMOS in POWER ON
status. Unplug the power cord from power supply before
clearing CMOS will be a best bet for user.
2-5.8 WAKE ON LAN FUNCTION (WOL1)
WOL1 : WAKE ON LAN (WOL) FUNCTION
Connect the Wake On LAN signal from LAN card
to WOL1
WOL1
+5V standby
GND
PME
This connector connects to a LAN card with a Wake On LAN output. The
connector powers up the system when a wake-up packet or signal is received
through the LAN card.
This feature requires that Wake On LAN feature is enabled at the BIOS
“Power Management Setup” and that your system has an ATX power supply with
at least 720mA / +5V standby power.
21
65DVB/65DV2
2-5.9 THERMAL SENSOR CONNECTOR (RT2)
RT2: THERMAL SENSOR CONNECTOR
a: Connect to RT2.
b: Connect this thermal sensor
to particular device which
generates lots of heat such
as Hard Driver, VGA chip, etc.
When connected, user could
observe the temperature
change from the BIOS
program.
USB2: 2nd USB Port
GAME/MIDI PORT
MIC port: Microphone Jack
Line In port: Audio In Jack
Line Out / Speaker Out port: Audio Out Jack
22
65DVB/65DV2
2-6 CONNECTORS
• In this section we list all external connectors that user will use them.
2-6.1 J2J3
J2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
HDD LED CONNECTOR
PIN
PIN
PIN
PIN
1M
2M
3M
4M
DESCRIPTION
J2
+5V
HDD LED SIGNAL
HDD LED SIGNAL
+5V
This connector supplies power to the cabinet's IDE
activity LED. Read and write activity by devices
connected to the Primary or SecondaryIDE
connector will cause the LED to light up.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
INFRARED CONNECTOR
PIN
PIN
PIN
PIN
PIN
6M
7M
8M
9M
10M
DESCRIPTION
INFRARED TRANSMIT SIGNAL
GND
INFRARED RECEIVE SIGNAL
NONE
+5V
This connector supports an optional wireless
transmitting and receiving infrared module. This
module mounts to a small opening on system cases
that support this feature.
User must also configure the setting through
BIOS program "Peripheral Setup" to select whether
UART2 is directed for use with COM2 or IrDA.
Use the five pins and connect a ribbon cable from
the module to the motherboard's IR connector
according to the pin definitions.
23
65DVB/65DV2
J2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
ATX POWER SWITCH
PIN 12M
PIN 13M
DESCRIPTION
J2
ATX POWER SWITCH
GND
The system power is controlled by a momentary
switch connected to this lead.
Pressing the button once will switch the system
between ON and SOFT OFF.
Pushing the switch while in the ON mode for more
4 seconds will turn the system off.
The system power LED shows the status of the
system's power.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
SMI CONNECTOR
PIN 14M
PIN 15M
DESCRIPTION
24
SMI(System Managment Interrupt) SIGNAL
GND
This allows user to manually place the system into a
suspend mode or "Green" mode, where system
activity is decreased to save electricity and prolong
the life of certain components when the system is
not in use. This 2-oin connector connects to the
case-mounted suspend switch. If you do not have a
switch for the connector, you may use the "Turbo
Switch".
SMI is activated when it detects a short to open
moment and therefore leaving it shorted will not
cause any problems. This may require one or two
presses depending on the position of the switch.
Wake-Up can be controlled by settings in the BIOS
but the keyboard will always allow wake-up(the SMI
lead cannot wake up the system).
65DVB/65DV2
J3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
SPEAKER CONNECTOR
PIN
PIN
PIN
PIN
1M
2M
3M
4M
SPEAKER SIGNAL
NONE
GND
+5V
This SPEAKER connector connects to the casemounted speaker. Two sources (LINE OUT and
SPEAKER) allow you to hear system beeps and
warnings. Only SPEAKER allows you to hear system
beeps before the integrated audio has been properly
initialized.
DESCRIPTION
J3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
RESET SWITCH CONNECTOR
PIN 5M
PIN 6M
RESET SIGNAL
GND
RESET SWITCH connector connects to the casemounted reset switch for rebooting your system
without having to turn off your power switch. This is
a preferred method of reboot to prolong the life of
the system's power supply.
DESCRIPTION
J3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
SUSPEND LED
PIN 14M
PIN 15M
DESCRIPTION
SUSPEND LED SIGNAL
GND
Connect to Suspend indicator light.
25
65DVB/65DV2
2-6.2 CHASSIS PANEL CONNECTOR
A.
B.
E.
F.
C.
G.
A
B
C
D
E
F
G
H
I
J
K
D.
H.
I.
J.
K.
: PS/2 MOUSE PORT
: USB 0 PORT
: LPT1 PORT
: GAME/MIDI PORT
: PS/2 KEYBOARD PORT
: USB 1 PORT
: COM1 PORT
: COM2 PORT
: LINE / SPEAKER OUT
: LINE IN
: MICROPHONE
2-6.3 ATX POWER SUPPLY CONNECTOR
• This connector connects to an ATX power supply. The plug from the power
supply only inserts in an orientation because of the different hole sizes.
Find the proper orientation and push down firmly making sure that all pins
are aligned.
• Reminding that your power supply should support at least 10mA on the
5V standby voltage. It may cause an difficulty to power on the system if
the power supply cant support the load.
• For Wake On LAN function, the power supply should support at least
720mA current.
+12V
+5V Standby
Power Good
GND
VCC
GND
VCC
GND
VCC3
VCC3
26
VCC
VCC
-5V
GND
GND
GND
Power Supply on
GND
-12V
VCC3
65DVB/65DV2
2-6.4 AUDIO MODEM RISER SLOT (AMR)
The slot is a new open industry-standard specification for Audio/Modem
solution, which use the AC’97 interface as the connection between the riser
and the motherboard. Then specification main objective is to reduce the
baseline implementation cost of audio and modem. The motherboard uses
the primary channel for the on-board AC’97 code, so for using AMR
modem card on the motherboard, the AMR modem card must be
secondary.
DIMM3
DIMM2
DIMM1
16
ATX POWER
SOCKET 370
1
VIA
VT82C
693A
SW1
AMR
31
3
3
JP5
AGP 2X
IDE1
1 2 3 4 5 6
3
IDE2
USB2
1
DIP
JP11
4
CD_IN2 JP3 1
JP4 1
CD_IN1
1
RT1
Clock
Generator
FDC1
1
FAN1
ON
MIC
LINE
IN
GAME/MIDI PORT
LINE
OUT
COM2
COM1
LPT1
upper
upper
PS/2
USB0
MOUSE
lower
lower
USB1
PS/2
K/B
Note: AMR modem card is not include with the motherboard.
4
JP6 1
JP7 1
PCI 1
Li
Battery
3
AC'97
Codec
3
3
3
1
JBAT1
SUSLED
PWR/LED
IR
RST
PCI 5
SPK
ISA
HD/LED
FLASH BIOS
JP8
1
3
JWOL1
PCI 4
VIA
VT82C
686B
PWR SUSPEND
RT2
PCI 3
AMR modem card
FAN2
JP9
1
PCI 2
1 1
J2 J3
27
65DVB/65DV2
2-6.5 PS/2 MOUSE AND PS/2 KEYBOARD
PIN 6 : None
PIN 5 : Mouse Clock
PIN 4 : Vcc
PIN 3 : GND
PIN 2 : None
PIN 1 : Mouse Data
PS/2 MOUSE
PIN 6 : None
PIN 5 : Keyboard Clock
PIN 4 : Vcc
PIN 3 : GND
PIN 2 : None
PIN 1 : Keyboard Data
PS/2 KEYBOARD
2-6.6 IRQ DESCRIPTION
IRQMM
IRQP 0P
Function DescriptionM
System TimerPP
IRQP 1P
Keyboard ControllerP
2P
IRQP 2P
Programmable InterruptP
N/A
IRQP 3P
Serial Port (COM 2)P
11
IRQP 4P
Serial Port (COM 1)P
12
IRQP 5PP
Priority
1
13P
IRQP 6P
Floppy Disk ControllerP
14
IRQP 7P
Parallel Port (LPT1)P
15
IRQP 8P
Real Time Clock (RTC)P
3
IRQP 9PP
4
IRQP 10PP
5P
IRQP 11PP
6P
IRQP 12P
PS/2 Mouse PortP
7
IRQP 13P
CoprocessorP
8
IRQP 14P
Primary IDE ChannelP
9
IRQP 15P
Secondary IDE ChannelP
10
• Both ISA and PCI expansion cards may require IRQs. System IRQs are
available to cards installed in the ISA expansion bus first, then any remaining IRQs are available to PCI cards. Currently, there are two types of
ISA cards.
• The original ISA expansion card design, now referred to as “Legacy” ISA
28
65DVB/65DV2
card, requires that you configurate the card’s jumpers manually and then
install it in any available slot on the ISA bus. To see a map of your used
and free IRQs in Windows 98, the Control Panel in My Computer, contains
a System icon, which gives you a Device Manager tab. Double-Clicking on
a specific hardware device gives you a Resources tab which shows the
Interrupt number and address. Double-Clicking Computers to see all the
interrupts and addresses for your system. Make sure that no two devices
use the same IRQ or your computer will experience problems when those
two devices are in use at the same time.
29
65DVB/65DV2
CHAPTER 3
SOFTWARE SETUP
3-1 ABOUT SOLTEK SUPPORT CD
• In Soltek support CD, it contains most informations for user’s requirement,
such as Acrobat Reader, BIOS, User’s Manual, Driver, Hardware Monitor
(if motherboard supports this function), Patch, and Utility etc.,User can
browse the CD and get further details in regard of our motherboard. Of
course, welcome to vendor’s website for the newest release.
3-2 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)
Step 1:
• Please put the Support CD attached to motherboard into the CD-ROM drive.
• When appears a welcome window as left screen, then user should choose “Install Driver”.
Step 2:
• Click on the “VIA Chipsets Driver”.
Step 3:
• Click on the “4-in-1 driver”.
Step 4:
• Click on the “Install VIA 4-in-1 driver” to continue.
Step 5:
• Press Next button to continue.
30
65DVB/65DV2
Step 6:
• Click “Yes” to continue.
Step 7:
• Press select the checkbox as below:
Bus Master PCI IDE Driver
AGP VxD Driver
VIA Chipset Function’s Registry
IRQ Routing Miniport Driver
Note: For user who are upgrading VIA Drivers. We
recommend installing the 4-in-1 as it will
automatically detect and update the necessary
drivers.
Step 8:
• Click “Install” and Press Next button to continue.
31
65DVB/65DV2
Step 9:
• We recommend user to leave “Enable / Disable
[Ultra] DMA” checkbox empty.
Note: Whether select this item or not, user needs to
enable the Hard Disk DMA function in Control
Panel manually. (For further details, please
refer to next page)
Step 10:
• The default setup destination is C:\VIADMATOOL,
press Next button to continue.
Step 11:
• Press Next button to continue.
32
65DVB/65DV2
Step 12:
• Select “Install VIA AGP VxD” in turbo mode and
press Next button to continue.
Step 13:
• After all the setup process is finished, please restart
your computer by clicking on Finish.
A
bout Hard Disk DMA Function
Last but not least, user must enable the Hard Disk DMA function. The process is below:
1. [Start] [Setting] [Control Panel] [System] [Device Manager].
2. In Device Manager, select [Disk Drivers] [GENERIC IDE TYPEXX].
3. Select [Properties] for GENERIC IDE TYPEXX.
4. In Properties, select [Settings].
5. In Option item, select the DMA checkbox.
6. Restart your computer.
33
65DVB/65DV2
3-3 AC’97 AUDIO CODEC INSTALLATION
Step 1:
• Please put the Support CD attached to motherboard into the CD-ROM drive.
• When appears a welcome window as left screen, then user should choose “Install Driver”.
Step 2:
• Click on the “VIA Chipsets Driver”.
Step 3:
• Click on the “AC’97 driver”.
Step 4:
• Press Next button to continue.
Step 5:
• When asking you install or remove the audio driver,
please select “Install” and press Next button to
continue.
Step 6:
• It’s recommended for user to restart the computer
after the audio driver is finished. Please select “Yes,
I want to restart my computer now”.
34
65DVB/65DV2
3-4 HARDWARE MONITOR INSTALLATION
Step 1:
• Please put the Support CD attached to motherboard into the CD-ROM drive.
• When appears a welcome window as left screen, then user should choose “Install Driver”.
Step 2:
• Click on the “VIA Chipsets Driver”.
Step 3:
• Click on the “Hardware Monitor Utility”.
Step 4:
• Press Next button to continue.
Step 5:
• The default destination is C:\VIAhm, then press
Next button to continue.
Step 6:
• Press Next button to finish the Hardware Monitor
setup process.
35
65DVB/65DV2
CHAPTER 4
BIOS SETUP
4-1 INTRODUCE THE BIOS
• BIOS stands for Basic Input Output System. It is sometimes called ROM
BIOS because it is stored in a Read-Only Memory(ROM) chip on the
motherboard. BIOS is the first program to run when you turn on your
computer.
• BIOS performs the following functions:
1. Initializing and testing hardware in your computer (a process called “POST”,
for Power On Self Test).
2. Loading and running your operating system.
3. Helping your operating system and application programs to manage your
PC hardware by means of a set of routines called BIOS Run-Time Service.
4-2 WHAT IS BIOS SETUP
• Setup is an interactive BIOS program that you need to run when:
1. Changing the hardware on your system. (For example: installing a new
Hard Disk etc.)
2. Modifying the behavior of your computer. (For example: changing the
system time or date, or turning special features on or off etc.)
3. Enhancing your computer’s behavior. (For example: speeding up performance by turning on shadowing or caching)
4-3 HOW TO RUN BIOS SETUP
• One way of running SETUP is to press a special function key or key combination during POST, before the operating system is loaded during POST,
the BIOS usually displays a prompt such as:
Press DEL to enter SETUP
36
65DVB/65DV2
4-4 WHAT IS CMOS
• CMOS is a special kind of memory maintained by a battery after you turn
your computer off. The BIOS uses CMOS to store the settings you selected
in SETUP. The CMOS also maintains the internal clock. Every time you
turn on your computer, the BIOS Looks in CMOS for the settings you selected and configures your computer accordingly. If the battery charge runs
too low, the CMOS content will be lost and POST will issue a “CMOS invalid” or “CMOS checksum invalid” message. If this happens, you may
have to replace the battery. After the battery is replaced, the proper settings will need to be stored in SETUP.
4-5 WHAT IS POST
• POST is an acronym for Power On Self Test. It’s a traditional name for the
routines that the BIOS uses to test and initializes the devices on your system when the PC is powered on. Its meanings has grown to include anything the BIOS does before the operating system is started. Each of POST
routines is assigned a POST code, an unique number which is sent to I/O
port 080h before the routine is executed.
4-6 BIOS UPGRADE
• Motherboards incorporate the system BIOS in a Flash memory component.
Flash BIOS allows user upgrades without the need to replace an EPROM
component.
• The upgrade utility fits on a floppy diskette and provides the capability to
save, verify, and update the system BIOS. The upgrade utility can be run
from a hard disk drive or a network drive, but no memory managers can be
installed during upgrades.
4-6.1 BEFORE UPGRADE BIOS
• It is recommended that you save a copy of the original motherboard BIOS
along with a Flash EPROM Programming utility (AWDFLASH.EXE) to a
bootable floppy disk in case you need to reinstall the BIOS later.
37
65DVB/65DV2
4-6.2 UPGRADE PROCESS
Note: Normally, to upgrade BIOS that is unnecessary if the system is working fine
without any problem, user should upgrade the BIOS unless you experienced
incompatible problem or need BIOS upgrade to create new features. However,
please read all information in this section before upgrading.
“AWDFLASH.EXE” is a Flash EPROM Programming utility that updates the
BIOS by uploading a new BIOS file to the programmable flash ROM on the
motherboard, This program only works in pure DOS environment, the utility
can not be worked in win95/98, ME, NT or WINDOWS 2000 environment.
Upgrading the system BIOS
Set 1. Pleas visit the board maker’s website, download the newest BIOS file and
newest award flash utility “AWDFLASH.ESE” for the motherboard. The BIOS
file you downloaded will be a *. bin format.
Step 2. Create a bootable diskette. Then copy the BIOS file and award flash utility
“AWDFLASH,EXE” into the diskette.
Step 3. Insert the diskette into drive A, reboot you system and boot form the diskette.
Step 4. When booting is finished type awdflash *.bin/sn/py/cc and then press
<Enter> to run BIOS upgrade program. (*.bin depends on your motherboard
model and version code).
Step 5. After upgraded, please press <F1> or <F10> to exit or reset your system,
Warning ! If there appears Write Fail while Award “FLASH MEMORY
WRITER” verifying Flash memory, just repeat the process, please DO NOT
reset or turn off the system. If the award memory flash utility was not able to
update the BIOS successfully, you system may not able to boot up,
Step 6. You will see a message “CMOS checksum error-Default loaded” during
booting the system. Please press <Del> to run CMOS setup utility, then
reload ‘LOAD SETUP DEFAULTS” or “Load Optimized Defaults” and
save this change.
38
65DVB/65DV2
Figure 1 : Award Flash Memory Writer Start Screen
Figure2 : Award Flash Memory Writer Complete Screen
39
65DVB/65DV2
The parameters of AWDFLASH.EXE
/sn: No original BIOS backup
/py: Program flash memory
/cc: Clear CMOS data after programming
/r : Reset system after programming
NOTE: User can type AWDFLASH /? to get further details about
parameters. Wrong usage of parameter will damage the BIOS
information, so that we strongly recommend user to leave parameters away unless you realize their function.
40
65DVB/65DV2
4-7 CMOS SETUP UTILITY
• This motherboard comes with the AWARD BIOS from AWARD Software
Inc. Enter the CMOS SETUP UTILITY Main Menu by:
1. Turn on or reboot your system. After a series of diagnostic checks, the
following message will appear:
PRESS <DEL> TO ENTER SETUP
2. Press the <DEL> key and the main program screen will appear as follows.
CMOS Setup Utility - Copyright (C) 1984 - 2000 Award Software
Standard CMOS Features
Frequency Control
Advanced BIOS Features
Load Optimized Defaults
Advanced Chipset Features
Set Supervisor Password
Integrated Peripherals
Set User Password
Power Management Setup
SAVE & EXIT SETUP
PnP/PCI Configurations
EXIT WITHOUT SAVING
PC Health Status
EscM : Quit
F10M : Save & Exit Setup
: Select Item
(Shift) F2 : Change Color
Time, Date, Hard Disk Type...
3. Using the arrows on your keyboard, select an option, and press <Enter>.
Modify the system parameters to reflect the options installed in your system.
4. You may return to the Main Menu anytime by pressing <ESC>.
5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and
reboots the system, and “EXIT WITHOUT SAVING” ignores your changes
and exits the program.
41
65DVB/65DV2
4-8 STANDARD CMOS SETUP
• Standard CMOS Setup allows you to record some basic system hardware
configuration and set the system clock and error handling. You only need
to modify the configuration values of this option when you change your
system hardware configuration or the configuration stored in the CMOS
memory gets lost or damaged.
Run the STANDARD CMOS SETUP as following:
1. Choose “STANDARD CMOS SETUP” from the Main Menu and a screen
with a list of option will appear:
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Standard CMOS Features
Date (mm:dd:yy)M
Time (hh:mm:ss)M
Wed, Nov 22 2000
17 : 11 : 15
IDE
IDE
IDE
IDE
Press
Press
Press
Press
Primary MasterM
Primary SlaveM
Secondary MasterM
Secondary SlaveM
Enter
Enter
Enter
Enter
Item Help
Menu Level
13022 MB
None
None
None
Drive AM
Drive BM
1.44M, 3.5 in.
None
VideoM
Halt OnM
Base MemoryM
Extended MemoryM
Total MemoryM
EGA/VGA
All Errors
640K
65472K
1024K
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys.
42
65DVB/65DV2
Date (mm:dd:yy) The BIOS determines the day of the week from the
other date information. This field is for information
only.
Press the left or right arrow key to move to the desired field (date, month, year). Press the PgUp or
PgDn key to increment the setting, or type the desired value into the field.
Time (hh:mm:ss) The time format is based on the 24-hour military-time
clock. For example, 1 p.m. is 13:00:00. Press the
left or right arrow key to move to desired field. Press
the PgUp or PgDn key to increment the setting, or
type the desired value into the field.
Primary / Secondary This field records the specifications for all non-SCSI
Master / Slave hard disk drives installed in your system. Refer to the
respective documentation on how to install the drives.
Drive A / Drive B Set this field to the type(s) of floppy disk drive(s) installed in your system. The choices are:
360KB, 5.25in.,
1.2MB, 5.25in.,
720KB, 3.5in.,
1.44MB, 3.5in.,
2.88MB, 3.5in.,
None.
Video Set this field to the type of video display card installed
in the system. The choices are:
Monochrome,
Color 40x25,
VGA / EGA, (default)
Color 80x25.
Halt On Set this warning feature for the type of errors that will
cause the system to halt. The choices are:
No Errors,
All, But Keyboard,
All, But Diskette,
All, But Disk / Key.
43
65DVB/65DV2
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
IDE Primary Master
IDE HDD Auto-DetectionM
Press Enter
IDE Primary MasterM
Access ModeM
Auto
Auto
CapacityM
10243 MB
CylinderM
HeadM
PrecompM
Landing ZoneM
SectorM
19846
16
65535
19845
63
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
44
65DVB/65DV2
4-9 ADVANCED BIOS FEATURES
• ADVANCED BIOS FEATURES allows you to improve your system performance or set up system features according to your preference.
Run the ADVANCED BIOS FEATURES as following:
1. Choose “ADVANCED BIOS FEATURES” from the Main Menu and a screen
with a list of option will appear:
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
45
65DVB/65DV2
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Advanced BIOS Features
Virus Warning
CPU Internal Cache
Disabled
Enabled
External Cache
CPU L2 Cache ECC Checking
Process or Number Feature
Quick Power On Self Test
First Boot Device
Enabled
Enabled
Disabled
Enabled
Floppy
Second Boot Device
Third Boot Device
Boot Other Device
HDD-0
CDROM
Enabled
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Disabled
Disabled
On
Fast
Disabled
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
6
250
Setup
OS Select For DRAM > 64MB
Video BIOS Shadow
C8000-CBFFF Shadow
CC000-CFFFF Shadow
Non-OS2
Enabled
Disabled
Disabled
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow
Disabled
Disabled
Disabled
Disabled
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
46
65DVB/65DV2
Virus Warning Enabled: Activates automatically when the system
boots up causing a warning message to
appear if there is anything attempting to
access the boot sector or hard disk partition table.
Disabled: No warning message will appear when there
is something attempting to access the boot
sector or hard disk partition table.
NOTE: Many diagnostic (or boot manager) programs which attempt to access the boot sector table can cause the above
warning message. If you will be running such a program,
we recommend that you disable the virus protection first.
CPU Internal Cache Cache memory is additional memory that is much
faster than conventional DRAM (system memory).
CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have
additional (external) cache memory. When the CPU
requests data, the system transfers the requested
data from the main DRAM into cache memory, for
even faster access by the CPU.
The External Cache field may not appear if your system does not have external cache memory.
External Cache Choose Enabled or Disabled. This option allows you
to enable or disable the external cache.
CPU L2 Cache ECC When you select Enabled, memory checking is enChecking able when the external cache contains ECC SRAMs.
The choice: Enabled, Disabled.
Process or Number The choice: Enabled, Disabled.
Feature
Quick Power On Self Select Enabled to reduce the amount of time required
Test to run the power-on self -test (POST). A quick POST
skips certain steps. We recommend that you normally disable quick POST. Better to find a problem
during POST than lost data during your work.
47
65DVB/65DV2
First/Second/Third/ The BIOS attempts to load the operating system from
Other Boot Device the devices in the sequence selected in these items.
The choice: Floppy, LS/ZIP, HDD, SCSI, CDROM,
Disabled.
Swap Floppy Drive This field is effective only in systems with two floppy
drives. Selecting Enabled assigns physical drive B
logical drive A, and physical drive A to logical drive B.
Boot Up Floppy Seek Enabled: During POST, BIOS checks the track number of the floppy disk drive to see whether
it is 40 or 80 tracks.
Disabled: During POST, BIOS will not check the track
number of the floppy disk drive.
Boot Up NumLock Toggle between On or Off to control the state of the
Status NumLock key when the system boots. When toggled
On, the numeric keypad generates numbers instead
of controlling cursor operations.
Gate A20 Option Gate A20 refers to the way the system addresses
memory above 1 MB (extended memory). When set
to Fast, the system chipset controls Gate A20. When
set to Normal, a pin in the keyboard controller controls Gate A20. Setting Gate A20 to Fast improves
system speed, particularly with OS/2 and Windows.
Typematic Rate Setting When Disabled, the following two items (Typematic
Rate and Typematic Delay) are irrelevant. Keystroke
repeat at a rate determined by the keyboard controller in your system.
When Enabled, you can select a typematic rate and
typematic delay.
Typematic Rate (Chars Range between 6 and 30 characters per second. This
/ Sec) option controls the speed of repeating keystrokes.
48
65DVB/65DV2
Typematic Delay Choose 250, 500, 750 and 1000. This option sets
(Msec) the time interval for displaying the first and the second characters.
Security Option If you have set a password, select whether the password is required every time the System boots, or only
when you enter setup.
OS Select For DRAM > Non-OS/2: For Non-OS/2 system.
64MB OS: For OS/2 operating system.
Video BIOS Shadow Enabled copies Video BIOS to shadow RAM for improving performance.
The choice: Enabled, Disabled.
C8000-CBFFF to These options are used to shadow other expansion
DC000-DFFFF Shadow card ROMs.
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
49
65DVB/65DV2
4-10 ADVANCED CHIPSET FEATURES
• ADVANCED CHIPSET FEATURES allows you to change the values of
chipset registers. These registers control the system options.
Run the ADVANCED CHIPSET FEATURES as following:
1. Choose “ADVANCED CHIPSET FEATURES” from the Main Menu and a
screen with a list of option will appear:
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
50
65DVB/65DV2
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Advanced Chipset Features
Bank 0/1 DRAM TimingM
Bank 2/3 DRAM TimingM
Bank 4/5 DRAM TimingM
SDRAM Cycle LengthM
DRAM ClockM
Memory HoleM
Read Around WriteM
Concurrent PCI/HostM
System BIOS CacheableM
Video RAM CacheableM
AGP Aperture SizeM
AGP 2X Mode
CPU to PCI Write BufferM
PCI Dynamic BurstingM
PCI Master 0 WS WriteM
SDRAM 10ns
SDRAM 10ns
SDRAM 10ns
3
Host CLK
Disabled
Disabled
Disabled
Disabled
Disabled
64M
Enabled
Enabled
Disabled
Enabled
PCI Delay TransactionM
Enabled
PCI#2 Access #1 RetryM
AGP Master 1 WS WriteM
AGP Master 1 WS ReadM
USB Keyboard SupportM
OnChip SoundM
OnChip ModemM
OnChip USBM
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
51
65DVB/65DV2
Bank 0/1 2/3 4/5 DRAM This item allows you to select the value in this field,
Timing depending on whether the board has paged DRAMs
or EDO (Extended Data Output) DRAMs.
The choice: SDRAM 8/10ns,
Normal,
Medium,
Fast,
Turbo.
SDRAM Cycle Length You can select CAS latency time in HCLKs of 2/2 or
Time 3/3. The system board designer should have set the
values in this field, depending on the DRAM installed.
Do not change the values in this field unless you
change specifications of the installed DRAM or the
installed CPU.
DRAM Clock This item allows you to control the DRAM speed.
The choice: Host Clock, HCLK+33M, HCLK-33M.
Memory Hole In order to improve performance, certain space in
memory is reserved for ISA cards. This memory must
be mapped into the memory space below 16MB.
The choice: 15M-16M, Disabled.
Read Around Write DRAM optimization feature: If a memory read is addressed to a location whose latest write is being held
in a buffer before being written to memory, the read
is satisfied through the buffer contents, and the read
is not sent to the DRAM.
Concurrent PCI/Host Please leave it at default setting
System BIOS Choose Enabled or Disabled. When enabled, the
Cacheable access to the system BIOS ROM addressed at
F0000H - FFFFFH is cached.
52
65DVB/65DV2
Video RAM Cacheable Choose Enabled or Disabled. When enabled, the
access to the VGA RAM addressed is cached.
AGP Aperture Size Choose 4, 8, 16, 32, 64, 128 or 256 MB. Memory
mapped and graphics data structures can reside in a
Graphics Aperture. This area is like a linear buffer.
BIOS will automatically report the starting address of
this buffer to the O.S.
AGP-2X Mode This item allows you to enable / disable the AGP-2X
mode.
CPU to PCI Write When this field is Enabled, writes from the CPU to
Buffer the PCI bus are buffered, to compensate for the speed
differences between the CPU and the PCI bus. When
Disabled, the writes are not buffered and the CPU
must wait until the write is complete before starting
another write cycle.
The choice: Enabled, Disabled.
PCI Dynamic Bursting When Enabled, every write transaction goes to the
write buffer. Bursting transactions then burst on the
PCI bus and non-bursting transactions don’t.
The choice: Enabled, Disabled.
PCI Master 0 WS Write When Enabled, writes to the PCI bus are executed
with zero wait states.
The choice: Enabled, Disabled.
PCI Delay Transaction Leave this field at default
PCI #2 Access #1 Retry Leave this field at default
AGP Master 1 ws write Leave this field at default
AGP Master 1 ws read Leave this field at default
53
65DVB/65DV2
USB Keyboard Enabled: Enable function when the USB keyboard is
Support
being used.
Disabled: When the AT keyboard is being used,
choose disabled.
OnChip Modem Select Enabled to use the on-chip Modem capability
of your system. This field must be Disabled, if there
is NO AMR modem card installed.
OnChip Sound Select Enabled to use the on-chip Audio capability of
your system. Most of the following field do not
appear when this field is Disabled, for user who wants
to use another sound card, this field must be Disabled.
OnChip USB This should be enabled if our system has a USB installed on the system board and you wish to use it.
Even when so equipped, if you add a higher performance controller, you will need to disable this feature.
The choice: Enabled, Disabled.
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
54
65DVB/65DV2
4-11 INTEGRATED PERIPHERALS
• INTEGRATED PERIPHERALS option allows you to get some informations
inside your system when it is working.
Run the INTEGRATED PERIPHERALS as following:
1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a screen
with a list of option will appear:
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Integrated Peripherals
On-Chip IDE Channel 0
On-Chip IDE Channel 1
IDE Prefetch Mode
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master UDMA
Primary Slave UDMA
Secondary Master UDMA
Secondary Slave UDMA
Init Display First
IDE HDD Block Mode
Onboard FDD Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART 2 Mode
IR Function Duplex
TX, RX inverting enable
Onboard Parallel Port
Onboard Parallel Mode
ECP Mode Use DMA
Parallel Port EPP Type
Onboard Legacy Audio
Sound Blaster
SB I/O Base Address
SB IRQ Select
SB DMA Select
MPU-401
MPU-401 I/O Address
Game Port (200-207H)
Enabled
Enabled
Enabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
PCI Slot
Enabled
Enabled
Auto
Auto
Standard
Half
No, Yes
378/IRQ7
Normal
3
EPP1.9
Enabled
Disabled
220H
IRQ 5
DMA 1
Disabled
330-333H
Enabled
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
55
65DVB/65DV2
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
On-Chip Primary/ The chipset contains a PCI IDE interface with supSecondary PCI IDE port from two IDE channels. Select Enabled to activate the first and/or the second IDE interface. Select
Disabled to deactivate an interface if you install a primary and/or second add-on IDE interface.
The choice: Enabled, Disabled.
IDE Prefetch Mode The onboard IDE drive interfaces supports IDE
prefetching for faster drive accesses. If you install a
primary and/or secondary add-in IDE interfaces, set
this field to Disabled if the interface does not support
prefetching.
The choice: Enabled, Disabled.
Primary
Master / Slave PIO
Secondary
Master / Slave PIO
56
Choose Auto or Mode 0~4. The BIOS will detect the
HDD mode type automatically when you choose Auto.
You need to set to a lower mode than Auto when your
hard disk becomes unstable.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3,
Mode 4.
65DVB/65DV2
Primary
Master / Slave UDMA
Secondary
Master / Slave UDMA
Ultra DMA/66 implementation is possible only if your
IDE hard drive supports it and the operating environment includes a DMA drive and your system software
both support Ultra DMA/66, select Auto to enable
BIOS support.
The choice: Auto, Disabled.
Init Display First This option allows you to decide to activate PCI Slot
or AGP first.
The choice: PCI Slot, AGP.
IDE HDD Block Mode Block mode is also called block transfer, multiple
commands, or multiple sector read/write. If your IDE
hard drive supports block mode (most new drives do),
select Enabled for automatic detection of the optimal
number of block read/write per sector the drive can
support.
The choice: Enabled, Disabled.
Onboard FDC Select Enabled if your system has a floppy drive conController troller (FDC) installed on the system board and you
want to use it. If you install add-in FDC or the system
has no floppy drive, select Disabled in this field.
The choice: Enabled, Disabled.
Onboard Serial Select an address and corresponding interrupt for the
Port 1 / Port 2 first and second serial ports.
The choice: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/
IRQ3, Disabled, Auto.
UART 2 Mode This item allows you to select which mode for the
Onboard Serial Port 2.
The choice: Standard, HPSIR, ASKIR
IR Function Duplex This item allows you to select the IR half / full duplex
function.
The choice: Half, Full.
57
65DVB/65DV2
TX, RX inverting This item allows you to enable the TX, RX inverting
enabled which depends on different H/W requirement. This
field is not recommended to change its default setting for avoiding any error in your system.
The choice: “No, No”, “No, Yes”, “Yes, No”, “Yes, Yes”.
Onboard Parallel Port This item allows you to determine onboard parallel
port controller I/O address setting.
The choice: 378H/IRQ7, 278H/IRQ5, 3BC/IRQ7,
Disabled.
0nboard Parallel Port Select an operating mode for the onboard parallel
Mode (printer) port. Select Normal, Compatible, or SPP
unless you are certain your hardware and software
both support one of the other available modes.
The choice: SPP, EPP, ECP, ECP + EPP.
ECP Mode Use DMA Select a DMA channel for the parallel port for use
during ECP mode.
The choice: 3, 1.
Parallel Port EPP Type Select EPP port type 1.7 or 1.9
The choice: EPP1.7, 1.9.
Onboard Legacy Audio This field controls the onboard audio.
• Sound Blaster
• SB I/O Base Address
• SB IRQ Select
• SB DMA Select
• MPU-401
• MPU-401 I/O Address
• Game Port (200-207H)
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
58
65DVB/65DV2
4-12 POWER MANAGEMENT SETUP
• POWER MANAGEMENT SETUP allows you to set the system’s power
saving functions.
Run the POWER MANAGEMENT SETUP as following:
1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a
screen with a list of option will appear:
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Power Management Setup
ACPI Function
Power Management
PM Control by APM
Video Off Option
Video Off Method
MODEM Use IRQ
Doze Mode
Soft-Off by PWRBTN
State After Power Failure
Wake Up Events
Enabled
Press Enter
Yes
Suspend Off
V/H SYNC+Blank
3
Disable
Instand-Off
Auto
Press Enter
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
59
65DVB/65DV2
ACPI Function Select Enabled only if your computer’s operating system supports the Advanced Configuration and Power
Interface (ACPI) specification. Currently, Windows
NT 5.0 support ACPI.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Power Management
Power ManagementM
HDD Power DownM
Doze ModeM
Suspend ModeM
User Define
Disable
Disable
Disable
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Power Management This option allows you to select the type (or degree)
of power saving for Doze, Standby, and Suspend
modes.
This table describes each power management mode:
Max Saving Maximum power savings. Only Available for SL CPUs.
Inactivity period is 1 minute in each mode.
User Define Set each mode individually. Select time-out periods
in the section for each mode, below.
Min Saving Minimum power savings. Inactivity period is 1 hour
in each mode (except the hard drive).
HDD Power Down When enabled and after the set time of system
inactivity, the hard disk drive will be powered down
while all other devices remain active.
60
65DVB/65DV2
Doze Mode When enabled and after the set time of system
inactivity, the CPU clock will run at slower speed while
all other devices still operate at full speed.
Suspend Mode After the selected period of system inactivity, the
chipset enters a hardware suspend mode, stopping
the CPU clock and possibly causing other system
devices to enter power management modes.
PM Control by APM When enabled, an Advanced Power Management
device will be activated to enhance the Max. Power
Saving mode and stop the CPU internal clock, If Advanced Power Management (APM) is installed on your
system, selecting Yes gives better power savings. If
the Max. Saving is not enabled, this will be present to
No.
Video Off Option When enabled, this feature allows the VGA adapter
to operate in a power saving mode.
Always On
Monitor will remain on during power saving modes.
Suspend --> Off
Monitor blanked when the systems enters the Suspend
mode.
Susp, Stby --> Off
Monitor blanked when the system enters either Suspend or
Standby modes.
Video Off Method This determines the manner in which the monitor is
blanked.
V/H SYNC + Blank
Blank Screen
DPMS
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to the
video buffer.
This option only writes blanks to the video buffer.
Select this option if your monitor supports the Display Power
Management Signaling (DPMS) standard of the Video
Electronics Standards to select video power management
values.
61
65DVB/65DV2
MODEM Use IRQ Name the interrupt request (IRQ) line assigned to the
modem (if any) on your system. Activity of the selected IRQ always awakens the system.
The choice: 3, 4, 5, 7, 9, 10, 11, NA.
Soft-Off by PWRBTN Instant-Off : Turn off the system power at once after
pushing the power button.
Delay 4 Sec: Turn off the system power 4 seconds
after pushing the power button. (To meet PC97/98
spec)
State After Power This field lets you determine the state that your PC
Failure returns to after a power failure.
The choice: On, Off, Auto
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Wake Up Events
VGA
LPT & COM
HDD & FDD
PCI Master
Modeam Ring Resume
RTC Alarm Resume
Date (of Month)
Resume Time (hh:mm:ss)
IRQS Activity Monitoring
OFF
LPT/COM
ON
OFF
Disabled
Disabled
0
0 0 0
Press Enter
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
VGA When Enabled, you can set the VGA awakens the
system
62
65DVB/65DV2
LPT & COM When On of LPT & COM, any activity from one of the
listed system peripheral devices or IRQs wakes up
the system.
HDD & FDD When On of HDD & FDD, any activity from one of the
listed system peripheral devices wakes up the system.
PCI Master When On of PCI Master, any activity from one of the
listed system peripheral devices wakes up the system.
Modem Ring Resume An input signal on the serial Ring Indicator (RI) Line
(in other words, an incoming call on the modem) Awakens the system from a soft off state.
RTC Alarm Resume When Enabled, you can set the data and time at the
which the RTC (Real Time Clock) alarm awakens the
system from suspend mode.
The choice: Disabled, Enabled.
Date (of Month) Set a certain date when RTC Alarm Resume option
is Enabled to awaken the system. This option is concurrent with Resume Time option.
Resume Time (hh:mm: Set a certain time when RTC Alarm Resume option is
ss) Enabled to awaken the system. This option is concurrent with Date option.
63
65DVB/65DV2
The following is a list of IRQ’s (Interrupt Requests), which can be exempted
much as the COM ports and LPT ports above can. When an I/O device
wants to gain the attention of the operating system, it signals this by causing
an IRQ to occur. When the operating system is ready to respond to the
request, it interrupts itself and performs the service. When set On, activity
will neither prevent the system from going into a power management mode
nor awaken it.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
MIRQ Activity Monitoring
Primary INTR
IRQ 3 (COM2)M
IRQ 4 (COM1)M
IRQ 5 (LPT2)M
IRQ 6 (Floppy Disk)M
IRQ 7 (LPT1)M
IRQ 8 (RTC Alarm)M
IRQ 9 (IRQ2 Redir)M
IRQ 10 (Reserved)M
IRQ 11 (Reserved)M
IRQ 12 (PS/2 Mouse)M
IRQ 13 (Coprocessor)M
IRQ 14 (Hard Disk)M
IRQ 15 (Reserved)M
ON
Primary
Primary
Primary
Primary
Primary
Disabled
Secondary
Secondary
Secondary
Primary
Disabled
Primary
Disabled
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
64
65DVB/65DV2
4-13 PNP / PCI CONFIGURATION
• PNP/PCI CONFIGURATION allows you to set the system’s power saving
functions.
Run the PNP/PCI CONFIGURATION as following:
1. Choose “PNP/PCI CONFIGURATION” from the Main Menu and a screen
with a list of option will appear:
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
PnP/PCI Configurations
PNP OS Installed
Reset Configuration Data
No
Disabled
Resources Controlled By
IRQ Resources
DMA Resources
Auto(ESCD)
Press Enter
Press Enter
PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB
Disabled
Enabled
Enabled
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
2. Use one of the arrow keys to move between options and modify the selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
65
65DVB/65DV2
PNP OS Installed Select Yes if the system operating environment is
Plug-and Play aware (e.g., Windows 95).
NOTE: BIOS will automatically disable all PnP resources except
the boot device card when you select Yes on Non-PnP
operating system.
Reset Configuration Normally, you leave this Disabled. Select Enabled to
Data reset Extended System Configuration Data (ESCD)
when you exit Setup if you have installed a new addon and the system reconfiguration has caused such
a serious conflict that the operating system cannot
boot.
Resource Controlled The plug and play AwardBIOS can automatically conBy figure all the boot and play-compatible devices. If
you select Auto, all the interrupt request (IRQ) and
DMA assignment fields disappear, as the BIOS automatically assigns them.
IRQ Resources Press Enter. Please refer to the below list.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
IRQ Resources
IRQ-3
IRQ-4
IRQ-5
IRQ-7
IRQ-9
IRQ-10
IRQ-11
IRQ-12
IRQ-14
IRQ-15
assigned
assigned
assigned
assigned
assigned
assigned
assigned
assigned
assigned
assigned
to
to
to
to
to
to
to
to
to
to
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
PnP
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
66
65DVB/65DV2
DMA Resources Press Enter. Please refer to the below list.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
DMA Resources
DMA-0
DMA-1
DMA-3
DMA-5
DMA-6
DMA-7
assigned
assigned
assigned
assigned
assigned
assigned
to
to
to
to
to
to
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PnP
PnP
PnP
PnP
PnP
PnP
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
PCI/VGA Palette Snoop Leave this field at Disabled.
The choice: Enabled, Disabled.
Assign IRQ for VGA Enabled: Add one IRQ to VGA controller.
Disabled: Remove IRQ from USB controller. The system will have extra IRQ for other devices but the VGA
controller will still not be disabled. (Only IRQ was
removed)
Assign IRQ for USB Enabled: Add one IRQ to USB controller.
Disabled: Remove IRQ from USB controller. The system will have extra IRQ for other devices but the USB
controller will still not be disabled. (only IRQ was
removed)
3. Press <ESC> to return to the Main Menu when you finish setting up all
items.
67
65DVB/65DV2
4-14 PC HEALTH STATUS
• This section helps you to get more information about your system including
CPU temperature, FAN speed and voltage. It is recommended that you
contact with your motherboard supplier to get proper value about your setting of the CPU temperature.
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
PC Health Status
Current
Current
Current
Current
Vcore
2.5V
3.3V
5V
12V
CPU Temp
System Temp
CPUFAN1 Speed
CPUFAN2 Speed
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Current CPU Temp. Shows current CPU temperature.
Current System Temp. Shows current system temperature.
Current CPU FAN1 Shows current CPU FAN1 speed. The fan must proSpeed vide rotary pulse. (Normally these types of fan have
a three-wire connector)
Current CPUFAN2 Shows current CPUFAN2 speed. The fan must proSpeed vide rotary pulse. (Normally these types of fan have
a three-wire connector)
Vcore Shows power supply actual voltage value.
• Press <ESC> to return to the Main Menu when you finish setting up all
items.
68
65DVB/65DV2
4-15 FREQUENCY/VOLTAGE CONTROL
CMOS Setup Utility - Copyright (C) 1984-2000 Award Software
Frequency Control
Auto Detect DIMM/PCI CLKM
Spread Spectrum M
CPU Host Clock (CPU/PCI)M
Disabled
Disabled
Default
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Auto Detect This item allows you to enable/disable detect DIMM/
DIMM/PCI CLK PCI Clock.
The choice: Enabled, Disabled.
Spread Spec- This item allows you to enable/disable the spread
trum Modulated spectrum modulate.
The choice: Enabled, Disabled.
CPU Host Clock This item allows you to select CPU/PCI frequency.
(CPU/PCI) The choice: Default, 100/33MHz, 103/34MHz, 105/
35MHz, 112/37MHz, 115/38MHz, 120/40MHz, 124/
41MHz.
• Press <ESC> to return to the Main Menu when you finish setting up all
items.
69
65DVB/65DV2
4-16 LOAD OPTIMIZED DEFAULTS
• When you press <Enter> on this item you get a confirmation dialog box
with a message similar to:
“ Load Optimized Defaults
(Y / N) ?
N ”
Pressing “Y” loads the BIOS default values that are factory settings for optimal performance system operations.
70
65DVB/65DV2
4-17 SET SUPERVISOR / USER PASSWORD
• These two options allow you to set your system passwords. Normally, the
supervisor has a higher ability to change the CMOS setup option than the
user. The way to set up the passwords for both Supervisor and User are
as follows:
1. Choose “Change Password” in the Main Menu and press <Enter>. The
following message appears:
“Enter Password :
“
2. The first time you run this option, enter your password up to 8 characters
and press <Enter>. The screen does not display the entered characters.
3. After you enter the password, the following message appears prompting
you to confirm the password:
“Confirm Password :
“
4. Enter the same password “exactly” as you just typed again to confirm the
password and press <Enter>.
5. Move the cursor to Save & Exit Setup to save the password.
6. If you need to delete the password or entered before, choose the Supervisor Password and press <Enter>. It will delete the password that you
had before.
7. Move the cursor to Save & Exit Setup to save the option you did, otherwise the old password will still be there the next time you turn your system
on.
8. Press <Enter> to exit to the Main Menu.
NOTE: If you forget or lose the password, the only way to access
the system is to clear the CMOS RAM. All setup informations will be lost and you need to run the BIOS setup program again.
71
65DVB/65DV2
4-18 SAVE & EXIT SETUP
• SAVE & EXIT SETUP allows you to save all modifications you have specified into the CMOS memory. Highlight this option on the Main Menu and
the following message appears:
“SAVE to CMOS and EXIT (Y/N) ?
Y “
Press <Enter> key to save the configuration changes.
4-19 EXIT WITHOUT SAVING
• EXIT WITHOUT SAVING option allows you to exit the Setup Utility without
saving the modifications that you have specified. Highlight this option on
the Main Menu and the following message appears:
“Quit Without Saving (Y/N) ?
N “
You may change the prompt to “Y” and press <Enter> key to leave this option .
72
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement