User Manual v1.0
User Manual v1.0
Safety instructions
Please read and follow these safety guidelines and assembly instructions in order to maintain safety of operators and people around:
•
•
•
•
•
•
•
Alarm and control device Esim251 (further referenced as the system) contains an integrated radio transceiver operating in GSM
850/900/1800/1900 MHz bands.
Don’t use the system where it can interfere with other devices and cause any potential danger.
Don’t mount the system next to medical equipment or devices, if they require so.
Don’t use the system in hazardous environment.
Don’t expose the system to high humidity, chemical environment or mechanical impacts.
Don’t attempt to personally repair the system.
System label is on the bottom side of the device.
System Esim251 is a device mounted in limited access areas. Any system repairs must be done only by qualified, safety aware
personnel.
Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance
must not be done during stormy conditions.
The system must be powered by main 10-24V 50Hz ~200mA AC or 10-24V
approved by LST EN 60950-1 standard and be easily accessible.
200mA DC power supply which must be
Any additional devices linked to the system Esim251 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
External power supply can be connected to AC mains only inside installation room with automatic 2-pole circuit breaker capable of disconnecting circuit in the event of short circuit or over-current condition. Open
circuit breaker must have a gap between connections of more than 3mm.
Phase
Null
PE
AC 230V
50 Hz/DC 24V
ESIM251
USB cable
Fuse F1 type C1S 2.5A. Blown fuse cannot be replaced by the user and the replacement fuses have to be exactly the same as
indicated by the manufacturer.
The device is fully turned off by disconnecting 2-pole switch off device of the external power supply or any other linked
device that the system Esim251 is powered from.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product or its documentation indicates that in the EU the
product must not be disposed of together with household waste.
Copyright © “ELDES UAB”, 2009. All rights reserved.
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from “ELDES
UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this
GSM ALARM AND CONTROL SYSTEM Esim251 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity may be consulted at www.eldes.lt/ce.
Limited Liability
The buyer must agree that the system will reduce
the risk of fire, theft, burglary or other dangers but
does not guarantee against such events.
“ELDES UAB” will not take any responsibility regarding personal, property or revenue loss while using
the system.
“ELDES UAB” responsibility according to local laws
does not exceed value of the purchased system.
“ELDES UAB” is not affiliated with GSM operators
providing cellular services therefore is not responsible for the quality of cellular services.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”.
Warranty period starts from the day the system has
been purchased by the end user. The warranty is
valid only if the system has been used as intended,
following all guidelines listed in the manual and
within specified operating conditions. Receipt with
purchase date must be kept as a proof.
The warranty is voided if the system has been
exposed to mechanical impacts, chemicals, high
humidity, fluids, corrosive and hazardous environment or other force majeure factors.
Package Content:
The system Esim251 ................... 1 pcs
Esim251 user manual ................. 1 pcs
GSM antenna ................................ 1 psc
Fastening holders ........................ 3 psc
About User Manual
This document describes remote alarm system
Esim251, its operation and installation.
It is very important to read User Manual before
start using the system.
A quick start guide is located in first two chapters.
Chapter 3 and 4 describe additional system capabilities.
CONTENT
1. General Information
1.1
1.2
1.3
1.4
1.5
1.6
Function .......................................................................................................4
Operation Description.............................................................................4
Technical Specifications .........................................................................5
Connector Functionality .........................................................................5
Connection Circuit. ...................................................................................6
System Installation ...................................................................................7
2. System Pre-operation and the Main Control Commands
2.1 Selecting device language
and verification of SMS central number ...........................................8
2.2 Password Change .....................................................................................8
2.3 User Numbers .............................................................................................9
2.3.1 Saving or Changing Numbers ..............................................9
2.3.2 Verification of Saved Numbers .............................................9
2.3.3 Deletion of Saved Numbers. .................................................9
2.4 Date and Time Settings ..........................................................................9
3. Additional System Capabilities
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Renaming Zones and Controlled Output ...................................... 10
Enabling/Disabling Zones................................................................... 10
Info on Status SMS...................................... ........................................... 11
Blocking Unknown Numbers............................................................. 11
Remote Microphone Listening ......................................................... 12
Managing C1 and C2 Controlled Outputs. Timer ....................... 12
SMS Message Delivery to Multiple Users ..................................... 12
Calling all users ...................................................................................... 13
Configuration for advanced users................................................... 14
3.9.1 Additional possibilities of configuring
zones (inputs) alarm and restore....................................... 25
3.9.2 Additional possibilities of controlling and
configuring controller C1 (relay output) ........................ 27
3.9.2.1 Settings of the output controlled by calls........ 27
3.9.2.2 Settings of the output controlled
by SMS messages ..................................................... 28
3.9.2.3 Output control settings by event time.............. 30
4. Appendix
4.1 Restoring Default Parameters. .......................................................... 32
4.2 Esim251 ConfigTool configuration software ................................ 32
4.2 Technical Support .................................................................................. 32
1. General Information
1.1 Function
Esim251 is a microcontroller based device used to inform users about the alarm in automatic or security systems and control one
electric appliance -relay.
1.2 Operation Description
Description of factory default settings.
Alarm and control system Esim251 works over GSM network. It works 24/7, i. e. it always reacts to the incoming signal.
When the alarm siren, motion sensor, fire alarm sensor, door sensor, any other sensor or PGM output gets activated, Esim251 system sends an SMS message and calls to the preset numbers until one of the five possible users answers the phone or rejects the
call or until the call will be ended by the mobile service provider. After hanging up the phone the system turns back to the previous
status. An SMS message with the name of the activated input (zone) is being sent until its successful delivery to one of the users or
until it is delivered to all users. If you answer the call, the microphone gets activated for listening. After “hanging up the phone” the
systems turs back to the previous status of active security.
Esim251 can control 1 electronic appliance (a relay) sending a password and a special command from a GSM phone of any of the
users. You can, for example, turn on the heating, lighting, lift the gates, blinds etc.
The system will ignore requests coming from unknown telephone number or SMS message with wrong password.
List of other configurable system possibilities.
Input types
Ways of activating an event
Normally open NO
Operation only when the signal is transmitted.
Normally closed NC
Operation only when the signal is switched.
Event when the input is
activated (Alarm)
SMS is delivered when the signal is transmitted to the input.
Event when the input is restored SMS is delivered when the previously transmitted signal in the
(Restore)
input disappears.
Impulse counting
SMS
Ways of transmitting an event
Calls
Turning on/off by SMS
Ways of controlling output
(relay)
Event register
4
Turning on/off by a call
SMS is delivered if the number of te preset number of impulses in
the input is exceeded. Max value is 4294967295 impulses.
Only SMS or various call combinations can be chosen. It is also
possible to use only calls. Any of the users can be assigned only
SMS or only calls or call combinations. Besides, any of the users can
be assigned a particular input (zone) or their combination.
E. g. a possibility to configure the system so that when input Z1 is
activated SMS are sent only to users NR1 and NR5, and when Z2
is activated SMS is sent to all users and the call would be for NR4
and so on.
When the functions SMSALL and CALLSALL are set SMS messages
are sent to all users and the call would be delivered regardless of
the fact whether the call was answered, rejected etc.
The relay can be turned on/off by sending the command by SMS
message. You can turn on/off :
1. for a permanent status
2. for a set period
3. for a set hour
4. repeating turning on/off.
The relay can be turned on/off by calling. You can turn on/off :
1. for a permanent status
2. for a set period
3. toggle (relay status changes after each call)
Automatic turning on at the
preset hour
The relay can be turned on for a set period at a set hour.
E. g. the relay is turned on at 18:00 and it is on for 5 hours. After 5
hours it turns on automatically notifying the user about that.
Event register function
When the computer is connected it is possible to see activations,
network strength etc.
EN
1.3 Technical Specifications
Electrical and mechanical specifications
Supply voltage
Current used in standby mode
GSM modem frequency
Number of “low” level (negative) inputs
Number of “high” level (positive) inputs
Allowable “low” level (negative) input voltage values
Allowable “high” level (positive) input voltage values
Number of outputs
Output type
C1 output maximum commutating values
Dimensions
Operating temperature range
10-24V 50Hz ~ 200mA max / 10-24V
50mA max
850/900/1800/1900 MHz
4
1
0-1.6V
5-50V
1
NO (relay)
1A/24V DC; 0,5A/125V AC
82x63x20mm
-20…+55oC
(-30...+55oC with limitations)
200mA max
1.4 Connector Functionality
Short explanation of the main units
USB
GSM MODEM
SIM
CARD
ANT
GSM
MODEM
LED1
LED2
MIC
AC/DC
RELAY
-
DEFAULT D1 D2
- COM Z5 Z4 Z3 Z2 Z1
Picture 1
USER MANUAL ELDES ESIM251 V1.0
SIM CARD
LED
DEFAULT
ANT
USB
GSM network 850/900/1800/1900 MHz
modem
SIM card
Light-emitting diodes indicator
Connectors (D1 and D2) for restoring
default settings
GSM antenna SMA type connector
Mini USB connector
Connector functionality
Labeling
AC/DC
RELAY
RELAY
COM
Z5
Z4
Z3
Z2
Z1
Explanation
Power supply pins
Dry relay contact. Normally open (NO)
Dry relay contact. Normally open (NO)
Common pin
“Low” level input Z5
“Llow” level input Z4”
“Low” level input Z3
“High” level input Z2
“Low” level input Z1
5
LED indicators functionality
LED1
LED2
Indicates SIM card status
Indicates network status
LED2 status
OFF
LED1 status
OFF
Meaning
SIM card is working properly
ON
SIM card error
Meaning
No network connection
Blinking 3 times per second
Poor network connection
Blinking 1 time per second
Medium network connection
ON
Excellent network connection
1.5 Connection Circuit
USEFUL INFORMATION
When choosing GSM cellular provider, it is worth inquiring whether the service is used in security application assuring fast and
reliable SMS message delivery and phone call connection.
USEFUL INFORMATION
When choosing GSM cellular provider, it is worth inquiring whether the service is used in security application assuring fast and
reliable SMS message delivery and phone call connection.
System Esim251 and security unit COM must be connected.
Inputs Z1,Z3,Z4,Z5 are connected to security unit PGM outputs if PGM are implemented as open collector circuit or any other
circuit and if it commutates with COM.
It is also possible to connect Z1, Z3, Z4, Z5 inputs to, for instance, motion sensor or any other sensor as well as automatics device
provided the inputs are commutated with COM.
Input Z2 is commutated with a “high level” impulse. Impulse duration is >600ms.
GSM communication and
control system ESIM251
AC/DC
RELAY
COM Z5 Z4
Z3
Z2
AC/DC
Metal box
PE contact
Z1
Fuse 500 mA
~10-24V
Picture3 AC power supply connection circuit
PGM1
PGM2
PGM3
PGM4
PGM5
+12V
HIGH
LEVEL
Alarm system or other appliance
Picture 2
6
~230V 50Hz
EN
1.6 System Installation
The system can be installed only in a metal or non-flammable plastic enclosure. If the metal enclosure and transformer is used it
is necessary to ground the enclosure using yellow/green colour cable. For the connection of 230V transformer use 3x0.75 mm2
1 thread double isolated cable. The primary circuit of the transformer must be connected through 0.5A fuse. 230V power supply
cables cannot be grouped with low voltage cable group. For the connection of power supply and output connectors use 1 thread
2x0.75 mm2 cable. For the connection of input/output connectors use 0.50 mm2 1 thread cable.
1. Fasten the system in the box using fastening holders.
2. Place SIM card in the holder but make sure that SIM card PIN code is disabled. (PIN code can be disabled by putting SIM card
into mobile phone and following proper menus). SIM card should not have any remaining SMS messages.
3. Connect the circuit as shown in fig. No 2. Power supply cables are connected last). When connecting Esim251 to security
central system power supply usually the security system AUX output is used.
4. When AC power supply (ground transformator) is used connect according to circuit no. 3. In this case you do not need to
connect any other power supplies.
5. The system will start in less than a minute. LED2 indicator should be blinking or be ON indicating connection to GSM.
USER MANUAL ELDES ESIM251 V1.0
7
2. System Pre-operation and
the Main Control Commands
VERY IMPORTANT!!!
Underscore symbol ‘_’ in this manual is used to represent space. When writing SMS messages, every underscore symbol should be
replaced by single space symbol. XXXX – means password. Don’t leave any space at the beginning and the end of the message.
To set Esim251 system parameters easier and quicker you can use the computer, USB cable and configuration program Esim251
ConfigTool. You can read more in chapter 3.2.
2.1 Selecting device language and verification of SMS central number
The language in which the device communicates with the user can be chosen before changing factory default password. To change
the language in the system that is already configured reset default settings as described in 3.1 appendix.
Send SMS message with the required language
code to the number of the SIM card inserted in
Esim251.
E.g., if you want to set the English language send
the following SMS message: EN
Table of
possible
languages
Language
Code
lithuanian
LT
english
EN
ESIM 251
30-60 seconds later you should get an SMS message:
russian
RU
„English language confirmed.“ Go to chapter 2.2 upon
reception of this message.
Otherwise check for network connection and call Esim251 system from your mobile and wait until the system drops the call. You
should get an SMS message asking to change default password. Ot- herwise check for network connection and change SMS central
number.
SMS central number is saved in SIM card, therefore if SIM card has been used to send SMS messages with a mobile phone,
then you don’t’ need to change SMS central number. Often SMS central number is already saved in SIM card by cellular
operator.
Central number can be entered by sending SMS message:
XXXX_SMS_+37011111111
XXXX – is a password. Default password is four zeros: 0000. SMS central number is provided by cellular network provider.
Example: 0000_SMS_+37069899992
Message should be sent to the number of SIM card which is placed into the system. If all went correct, the system will send a message: SMS central number has been successfully changed to +37011111111
2.2 Password Change
All SMS commands start with a password, please memorize it. Manufacturer default password is
four zeros 0000, which is necessary to change.
ESIM 251
0000_
PSW_XXXX
Manufacturer default password can be changed by sending the following SMS message to
Esim251:
0000_PSW_XXXX
To replace your password, send the following SMS message:
YYYY_PSW_XXXX
XXXX is any four digit number except four zeros.
Non-numerical characters like dots, colons, spaces are not allowed. YYYY is the old system password. If you forgot the password,
default manufacturer password can be restored, see chapter 4.1 for more details.
8
EN
2.3 User Numbers
The system Esim251 allows to pre-program up to five different mobile numbers which will have access to and control the system.
NR1 is mandatory while others can be skipped. All numbers must be entered starting with international country code, e. g. national
code for Lithuania is 370, UK – 44. By default the system starts sending all messages and in the event of alarm starts calling on the
first number, and if the first call is unsuccessful, it immediately tries reaching subscriber No2 etc.
2.3.1 Saving or Changing Numbers
Send SMS message with the following text to Esim251:
XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_NR4:37011111111_
NR5:37011111111
ESIM 251
XXXX_
NR1:370
11111111_
NR4:370
11111111
ESIM 251
XXXX_
NR3:370
11111111
Ones should be replaced with user numbers.
Numbers don’t have to be entered in sequential order right away. E. g. user can enter first and
fourth number by sending the following SMS message:
XXXX_NR1:37011111111_NR4:37011111111
Or individually one number at a time:
XXXX_NR3:37011111111
Numbers can be changed same way as described above. New number will overwrite old one, therefore no erasing is necessary.
2.3.2 Verification of Saved Numbers
To inquire the system about pre-programmed numbers, send the following SMS message:
ESIM 251
XXXX_
HELPNR
ESIM 251
XXXX_
NR3:DEL
ESIM 251
XXXX_
2009.01.
01_14:15
XXXX_HELPNR
The system will reply with all pre-programmed numbers.
2.3.3 Deletion of Saved Numbers
To erase NR2-NR5, send the following SMS message:
XXXX_NR2:DEL_NR3:DEL_NR4:DEL_NR5:DEL
E. g. XXXX_NR3:DEL
The system will not allow erasing first number NR1. It can only be modified.
2.4 Date and Time Settings
It is important to set correct date and time so that the system can send reports at specified times.
Date and time can be set by sending the following format SMS message:
XXXX_MMMM.mn.dd_va:mi
where MMMM means year; mn - month; dd - day; va - hour; mi - minutes
E. g. XXXX_2009.01.01_14:15
USER MANUAL ELDES ESIM251 V1.0
9
3. Additional System Capabilities
3.1 Renaming alarm, restore text and controller names
Manufacturer initially set the following zone and controlled output names:
Zone1, Zone2, Zone3, Zone4, Zone5, OUTPUT1
E. g. if during the alarm Z1 zone was triggered, the system sends SMS message with the text: Zone1
Alarm text changes are made by sending the following SMS message:
XXXX_Z1:NewAlarmText;Z2:NewAlarmText;Z3:NewAlarmText;Z4:NewAlarmText;Z5:NewAlarmText;
E. G. XXXX_Z1:Intrusion though the door;Z2:Fire sensor triggered;
Texts can be changed all at once for all zones, several of them or one by one. Maximum text for one zone
is 24 characters. The space is equal to one character. Each new text must be followed by a semi colon. As
semi colon is used for separating texts for different zones, it cannot be used in the middle of alarm texts
it can only be used at the end. Texts cannot be the same as control commands.
ESIM 251
XXXX_Z1:
trespaced;
Z2:
triggered
fire
detector;
Triggered zone restore text
If you want to be notified by an SMS message when the triggered zone is restored Restore mode must be turned on. The mode is
turned on by sending a particular SMS command. Please refer to chapter 3.9 or configuration program.
Zone restore text is changed by sending the following SMS mesaage:
XXXX_ZR1:NewRestoreText;ZR2:NewRestoreText;ZR3:NewRestoreText;ZR4:NewRestoreT
ext;ZR5:NewRestoreText;
Controller name can be changed by sending the following SMS message:
XXXX_C1:NewControllerName
Controller name cannot be followed by a semi colon. You cannot change zone names and controller
names at the same time.
E. g. XXXX_C1:PUMP
3.2 Enabling/Disabling Zones
NOTE
Manufacturer set all the zones activated, i. e. in mode ON.
USEFUL INFORMATION
The zones can be enabled/disabled together or separately one by one.
Enabling Zone
Any zone can be enabled by sending the following SMS message:
XXXX_Z1:ON;Z2:ON;Z3:ON;Z4:ON;Z5:ON;
10
ESIM 251
XXXX_C1:
PUMP
EN
Disabling Zone
Any zone can be disabled by sending the following SMS message:
ESIM 251
XXXX_
WINDOWS:
OFF;
XXXX_Z1:OFF;Z2:OFF;Z3:OFF;Z4:OFF;Z5:OFF;
E. g. XXXX_Z2:ON; or XXXX_WINDOWS:ON; or XXXX_Z2:OFF; or XXXX_WINDOWS:OFF;
3.3 Info on Status SMS
The system Esim251 can any time be inquired about signal strength and the status of zones active at the time when SMS message is
sent. At the same time system test is performed. If the answer to the request has been received, it means the system finely operates.
It is also useful for those using prepayment service – you can check if the credit in the account is sufficient for sending an SMS
message. Send the following SMS message:
XXXX_INFO
The reply SMS will have following info: e. g. 2008.08.07 11:15
Signal strength satisfactory. Z1:OK/ALARM Z2:OK/ALARM Z3:OK/ALARM Z4:OK/ALARM Z5:OK/ALARM
where OK means that the alarm in zone did not go off. ALARM – if it went off.
By default, this status SMS message will be sent daily at 11:00 in the morning. These parameters can
be configured by sending the following SMS message:
ESIM 251
XXXX_
INFO:01.
10
XXXX_INFO:PP.VV
PP – message period in days, valid values [00-10].
VV - time when message is sent, valid values [00-23].
E. g. XXXX_INFO:01.10 means that status message will be sent every 1 day at 10:00.
ESIM 251
XXXX_
INFO:0.2
If PP value is 0, and VV in the range of [1-23], then periodic status messages will be sent multiple times
per day, with period being specified as VV time.
E. g. XXXX_INFO:0.2 means that status message will be sent every 2 hours.
To disable periodic status messages send the following SMS message:
XXXX_INFO:00.00
The status messages will not be sent until enabling or restoring default parameters or receiving previously described XXXX_
INFO:PP.VV SMS message.
3.4 Blocking Unknown Numbers
By default Esim251 system can be controlled from any of the pre-programmed numbers NR1-NR5. However, the user can access
the system and control parameters and outputs from any number as long as password is known.
To enable this feature send the following SMS message:
XXXX_STR:ON
To disable this feature send the following SMS message:
XXXX_STR:OFF
USER MANUAL ELDES ESIM251 V1.0
11
3.5 Remote Microphone Listening
NOTE
To enable this feature it is necessary to connect microphone connector to MIC slot. The microphone is additional equipment
tha can be purchased in trading centers.
You can listen to what is going on in the secured premises by sending the following SMS message:
XXXX_MIC
The system will ring the sender of the received SMS, and upon answering the call, the user can listen to any sounds in the building.
The phone call must be answered within 20 seconds otherwise the system will stop trying and return to previous state.
3.6 Managing C1 Controller. Timer.
Alarm system Esim251 contains a controller C1- a relay output. It can be used to control various electrical devices such as electric
pumps, heating, lighting etc. When the controller is enabled RELAY connectors are connected.
The device is turned on by sending the following SMS message:
XXXX_C1:ON
ESIM 251
XXXX_
PUMP:
ON
The device is turned off by sending the following SMS message:
XXXX_C1:OFF
Instead of C1 it is also possible writing a real controller name.
E.g.. XXXX_PUMP:ON
Timer
Alarm system Esim251 has internal timer clock. This feature allows any controlled output to be switched on or off for a specified
time period. The following SMS command should be sent:
XXXX_C1:ON/OFF:vv.mm.ss
ON – output enabled. OFF – disabled
vv – hours, valid values [00-23] mm – minutes, valid values [00-59] ss - seconds, valid values [00-59]
It is not allowed to have all values equal zeros. Zeros it is not allowed to have all values equal
E. g. to switch the pump on for 01 minutes and 23 seconds, send SMS XXXX_PUMP:ON:00.01.23
ESIM 251
XXXX_
PUMP:
OFF:00.
01.23
If the pump was enabled before and user want to disable it for 01 minute and 23 seconds, send SMS
XXXX_PUMP:OFF:00.01.23
If you want to use more C1 Output capabilities as TOGGLE, automatic enabling and disabling for a particular hour or control, use configuration program „Esim251 ConfigTool” or see chapter 3.9.2
3.7 SMS Message Delivery to Multiple Users
Upon activated alarm in security system Esim251 SMS messages are repeatedly sent until first successful delivery to one of the
users. The system starts with NR1 and if delivery fails, it follows with NR2 etc.
It is also possible to set the system so that it sends SMS message to all recorded users.
12
EN
To enable this function send the following SMS message:
XXXX_SMSALL:ON
To disable this function send the following SMS message:
XXXX_SMSALL:OFF
If you want to configure SMS message delivery only for particular users or only for particular zones, refer to chapter 3.9 or use configuration program.
3.8 Calling all users
During the alarm Esim251 system starts calling NR1. If the call to NR1 was unsuccessful or the subscriber was out of network coverage the call is forwarded to NR2 etc. If the user rejected the call or answered te call during the alarm the system stops calling.
However, you can set the system to call all recorded users regardless of the fact whether the user answered or rejected the call, was
out of network coverage or was engaged.
To turn on this feature send the following SMS message:
XXXX_CALLALL:ON
ATTENTION!
When this feature is enabled it will not be possible to stop calling the next user in the sequence even if the call is answered.
To disable this function send the following SMS message:
XXXX_CALLALL:OFF
If you want to configure calling only to particular users or only for particular zones, refer to chapter 3.9 or use configuration program.
3.9 Configuration for advanced users
All features described in chapter 3.9 of the user manual can be configured using program Esim251 ConfigTool. But if there
is no possibility of connecting the computer or if you want to change the settings remotely you can do this via SMS messages. We
use changinf these settings by SMS message only for advanced users.
USER MANUAL ELDES ESIM251 V1.0
13
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 1
The user wants to connect Esim251 system to an existing alarm in a building where enterprise A and and enterprise B work. Both
enterprises use the same alarm system that has two zones.The alarm system has 5 programmable outputs (PGM).
Task NO1:
Configuring the system so that the director of a particular enterprise is informed about security enabling depending on which enterprise employee enabled the security system. The director of enterprise A (NO1) wants to receive an SMS message only and does not
want to receive any calls, the director of enterprise B (NO2) wants to receive a call and does not want to receive any SMS messages.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM1
PGM2
Worker A
NO4
Alarm
SMS
ESIM151
Alarm
Calls
Worker B
NO5
Janitor
GATES
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove the users that should not receive any alarm messages. Besides, as per factory
default settings, calling feature in the case of alarm is also enabled for all users therefore call function must be disabled for all users
except user NO2.
a) First of all security central unit must be programmed in the way so that when security is enabled in office A, PGM1 is triggered,
and when security is enabled in office B, PGM2 is triggered.
b) PGM1 is connected to Esim251 input Z1, and PGM2 is connected to Esim251 input Z2. (PGM2 should be “High level”)
c) The following two configuration SMS messages must be sent to Esim251 system:
XXXX_SMSEXTRA:Z1:SC2345,CC12345
where SC2345 means that alarm SMS message sending to users NO2-NO5 is disabled after Z1 zone is triggered. CC12345 means
that alarm calls are disabled for all users NO1-NO5 after Z1 zone is triggered.
XXXX_SMSEXTRA:Z2:SC12345,CC1345
where SC12345 means that alarm SMS message sending is disabled for all users NO1-NO5 after Z2 zone is triggered. CC1345 means
that all alarm calls are disabled for users NO1, NO3-NO5 after Z2 zone is triggered.
14
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Task NO2:
Configuring the system so that the janitor (NO3) is informed about the triggered perimeter sensor of field territory by SMS message and a call; and when the sensor is reset, the janitor receives SMS message only.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM3
Worker A
NO4
ESIM151
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Restore
SMS
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove the users that should not receive any alarm messages. Besides, as per factory
default settings, calling feature in the case of alarm is also enabled for all users therefore call function must be disabled for all users
except user NO3. SMS message sending feature must also be enabled for user NO3 when input Z3 is restored.
a) First of all security central unit must be programmed in the way so that when territory security perimeter sensor is triggered
PGM3 is activated.
b) PGM3 is connected to Esim251 input Z3
c) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:Z3:SC1245,CC1245,SE3
where SC1245 means that alarm SMS message sending to users NO1, NO2, NO4 and NO5 is disabled after Z3 is triggered. CC1245
means that alarm call feature is disabled for users NO1, NO2, NO4 and NO5 after zone Z3 I triggered. SE3 means that SMS message
sending feature is enabled for user NO3 after Z3 input is restored.
USER MANUAL ELDES ESIM251 V1.0
15
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 1
The user wants to connect Esim251 system to an existing alarm in a building where enterprise A and and enterprise B work. Both
enterprises use the same alarm system that has two zones.The alarm system has 5 programmable outputs (PGM).
Task NO3:
Configuring the system so that the intrusion to enterprise A premises is reported to the janitor (NO3) and enterprise A employee
(NO4) by SMS messages and calls. Enterprise A employee (NO4) wants to receive a call only in the case if the janitor (NO3) does not
answer the call, is out of network coverage or at that time the janitor’s telephone line is engaged.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM4
Worker A
NO4
ESIM151
Alarm
SMS/Calls
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for all users except users NO3 and NO4. As per factory default settings
in the case of alarm the system rings until the first answered call, therefore in this case nothing should be configured.
a) First of all security central unit must be programmed in the way so that when security sensors of enterprise A are triggered
the signal is transmitted to security central unit output PGM4.
b) PGM4 is connected to Esim251 input Z4
c) The following configuration SMS messages must be sent to Esim251 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_SMSEXTRA:Z4:SC125,CC125
Where SC125 means that alarm SMS message delivery feature is disabled for users NO1, NO2 and NO5 after Z4 zone is triggered.
CC125 means that alarm calls are disabled for users NO1, NO2 and NO5 after Z4 zone is triggered.
16
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Task NO4:
Configuring the system so that the intrusion to enterprise B premises is reported to the janitor (NO3) and enterprise B employee
(NO5) by SMS messages and calls, and the director of enterprise B (NO2) receives SMS message only. Enterprise B employee (NO5)
must receive the phone call even in the case when the janitor (NR3) answers the call.
PIR
PIR
Enterprise A
Director A
NO1
Enterprise B
Director B
NO2
Alarm system
PGM5
Alarm
SMS
ESIM151
Alarm
SMS/Calls
Worker A
NO4
Worker B
NO5
Janitor
GATES
Alarm
SMS/Calls
Janitor
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for users NO1, NO2 and NO4, and left enabled for users NO3 and NO5.
Also, it is necessary to enable mandatory calling feature for all preset users (see more in chapter 3.8).
a) First of all security central unit must be programmed in the way so that when security sensors are triggered the signal must
be transmitted to security central unit output PGM5.
b) PGM is connected to Esim251 input Z5
c) The following three configuration SMS messages must be sent to Esim251 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_CALLALL:ON
where CALLALL enables mandatory calling feature for all users.
XXXX_SMSEXTRA:Z5:SC14,CC124
where SC14 means that alarm SMS message sending feature is disabled for users NO1 and NO4 after Z5 zone is triggered.
CC124 means that alarm calls are disabled for users NO1, NO2 and NO4 after Z5 zone is triggered.
USER MANUAL ELDES ESIM251 V1.0
17
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 2.
The user wants to connect Esim251 system to the programmable outputs (PGM) of an existing alarm system. House territory is
entered through electrically controlled gates. There are 5 users in total. NO1 is the housekeeper, NO2 is a neighbour, NO3-NO5
are family members.
Task NO1:
Configuring the system so that house alarm activation is reported to the housekeeper (NO1) by SMS message and a call as well as
to the neighbour (NO2) but by SMS message only.
PIR
PIR
Alarm
SMS/Calls
Housekeeper
NO1
Neighbour
NO2
Alarm
SMS
Alarm system
Family members:
PGM
ESIM151
PIR
PIR
NO3
NO4
NO5
GATES
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to enable mandatory SMS message delivery (see more in chapter 3.7) and to remove
the users who should not receive alarm messages. Besides, as per factory default settings, calling feature in the case of alarm is also
enabled for all users therefore call function must be disabled for users NO2-NO5 and left enabled for NO1 only.
a) First of all security central unit must be programmed in the way so that when security sensors are triggered the signal must
be transmitted to security central unit output PGM.
b) PGM is connected to Esim251 input Z1
c) The following two configuration SMS messages must be sent to Esim251 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery for all users.
XXXX_SMSEXTRA:Z1:SC345,CC2345
Where SC345 means that alar SMS message sending is disabled for users NO3, NO4 and NO5 after Z1 zone is triggered.
CC2345 means that alarm calls are disabled for all users exept NO1 after Z1 zone is triggered.
18
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Task NO2:
Configuring the system so that house gates could be opened via free calls by the housekeeper (NO1) and his family members
(NO3), (NO4) and (NO5). After every successful gate opening the user NO5 wants to receive a confirmation call (CALLBACK) the
duration of which is 3 seconds, and the user NO3 wants to receive a confirmation SMS message.
Control
Call
Confirmation
SMS
Gate controller
ESIM151
Housekeeper
NO1
Family member
NO3
Family member
NO4
Confirmation
Call
3 sek.
Family member
NO5
GATES
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set the
users who will be able to control the output. Besides, it is also necessary to set relay status for every user when he/she calls the system. In this case the relay must be activated and the activation duration must be 1 second; after this the relay returns to the previous
status. Confirmation call feature must be enabled for user NO5 and it is necessary to choose the length parameters for that call. Also,
confirmation SMS messages have to be enabled for user NO3.
a) First of all Esim251 system relay output has to be connected to the connectors of gate control unit.
b) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:COC:CE1345,CS5,CT513,SS3,MS10,MS30,MS40,MS50,MS1T0.0.1,MS3T0.0.1,MS4T0.0.1,MS5T0.0.1
where CE1345 means that C1 relay control via call is enabled for users NO1, NO3-NO5.
CS5 means that confirmation call feature is enabled for user NO5 after C1 relay status changes.
CT513 means that user NO5 will receive a confirmation call when the relay gets activated and call duration is 3 seconds.
SS3 means that user NO3 will be informed about C1 relay status change by SMS message.
MS10 means that the relay is activated when user NO1 calls the system.
MS30 means that the relay is activated when user NO3 calls the system.
MS40 means that the relay is activated when user NO4 calls the system.
MS50 means that the relay is activated when user NO5 calls the system.
MS1T0.0.1 means that relay status is changed for 1 second when user NO1 calls the system.
MS3T0.0.1 means that relay status is changed for 1 second when user NO3 calls the system.
MS4T0.0.1 means that relay status is changed for 1 second when user NO4 calls the system.
MS5T0.0.1 means that relay status is changed for 1 second when user NO5 calls the system.
USER MANUAL ELDES ESIM251 V1.0
19
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 3.
The user wants to connect Esim251 system to the heating system of the house.
Task No1:
Configuring the system so that house heating system is turned on and turned off by the user (NO1) via free call. This user should
also receive free information abut successful turning on or turning off of the heating system.
Flood detector
User
NO1
Heating
Controller
User
NO2
ESIM151
Confirmation
Call
3sek/10sek
Control
Call
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set the
users who will be able to control the output – in this case it is user NO1. Besides it is also necessary to set relay status for user NO1
when he/she calls the system. In this case you must set the system so that the relay is activated after one call and deactivated after
another one (Toggle) and so on. User NO1 needs to enable confirmation call feature and set the length parameters for that call. To
differentiate whether the relay was enabled confirmation call will be set to ring for 3 seconds and the confirmation call will ring for
10 seconds when the relay is disabled.
a) First of all Esim251 system relay output C1 has to be connected to the connectors of heating system control unit.
b) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:COC:CE1,CS1,CT113,CT1010,MS12
where CE1 means that C1 relay control via call is enabled for users NO1.
CS1 means that confirmation call feature is enabled for user NO1 after C1 relay status changes.
CT113 means that user NO1 will receive a confirmation call when the relay gets activated and call duration is 3 seconds.
CT1010 means that user NO1 will receive a confirmation call when the relay is deactivated and call duration is 10 seconds.
MS12 means that Toggle mode is activated for user NO1 which means that relay status is changed with every call.
20
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Task No2:
Configuring the system so that users (NO1) and (NO2) receive SMS message about a burst water pipe (flood) at home. SMS messages must be delivered to both users.
Flood detector
User
NO1
Heating
Controller
User
NO2
Alarm
SMS
ESIM151
Alarm
SMS
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message and calling in the case of alarm is enabled for all users until the first answered call, calling feature in the
case of alarm must be disabled for users NO1 and NO2. Mandatory SMS delivery to all users must also be enabled.
a) First of all a flood sensor is connected to Esim251 input Z1.
b) The following configuration SMS messages must be sent to Esim251 system:
XXXX_SMSALL:ON
where SMSALL enables mandatory SMS message delivery feature for all users.
XXXX_SMSEXTRA:Z1:CC12
where CC12 means that alarm call feature is disabled for users NO1, NO2 after Z1 zone activation.
We make an assumption that users NO3-NO5 were not entered to the system at all.
USER MANUAL ELDES ESIM251 V1.0
21
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 4.
The company taking care of automatic systems needs to have information about critical breakdowns of mechanisms and has to
quickly react and eliminate the breakdown. There are three members of operating personnel (NO1), (NO2) and (NO3).
Task No1:
Configuring the system so that operating personnel member (NO1) receives SMS message about the breakdown of gas boiler.
Working normally a gas boiler transfers a signal, and when it breaks down the signal is not transmitted.
Pump
Worker
NO1
Gas boiler
Fault
signal
ESIM151
Alarm
SMS
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove users NO2 and NO3 and disable alarm calls for all users. It is also necessary to
invert Esim251 input from NO to NC mode so that alarm is given only when the signal disappears.
a) First of all a signal indicating gas boiler breakdown isconnected to Esim251 input Z1.
b) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:Z1:SC23,CC123,LI1
where SC23 means that alarm SMS message sending is disabled for users NO2, NO3 after Z1 zone is activated.
CC123 means that alarm calls are disabled for users NO1, NO2 and NO3 after Z1 zone is activated.
We make an assumption that users NO4-NO5 were not entered to the system at all. LI1 means that NC “normally closed” - mode is enabled for the input.
22
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Task No2:
Configuring the system so that the operating personnel member (NO2) receives SMS message if the pump was triggered for 10
times.
Pump
Worker
NO1
Gas boiler
ESIM151
Alarm
SMS
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings SMS message sending feature in the case of alarm is enabled for all users until the first successful
delivery of the SMS message, it is necessary to remove users NO1 and NO3 and disable alarm calls for all users. It is also necessary to
enable impulse counting mode for Esim251 input Z3 and set the number of expected impulses.
a) First of all a signal indicating PUMP triggering is connected to Esim251 input Z3.
b) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:Z3:SC13,CC123,IE1,IC10
where SC13 means that alarm SMS message sending is disabled for users NO1, NO3 after Z3 zone activation.
CC123 means that alarm calls are disabled for users NO1, NO2 and NO3 after Z3 zone activation.
We make an assumption that users NO4-NO5 were not entered to the system at all.
IE1 enables impulse counting mode for zone Z3. IC10 means that the alarm is given to Z3 input after 10 impulses are transmitted.
USER MANUAL ELDES ESIM251 V1.0
23
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
E. g. 4.
The company taking care of automatic systems needs to have information about critical breakdowns of mechanisms and has to
quickly react and eliminate the breakdown. There are three members of operating personnel (NO1), (NO2) and (NO3).
Task No3:
Configuring the system so that operating personnel members (NO1), (NO2) and (NO3) can reboot the “hanged” automatic control
system without going to the object but via a short call to Esim251 system.
Pump
Worker
NO1
Gas boiler
ESIM151
Control
Calls
Automatic
system
Worker
NO2
Worker
NO3
As per factory default settings C1 output control via calls is disabled for all users, it is necessary to enable this feature and to set
the users who will be able to control the output. Besides, it is also necessary to set relay status for every user when he/she calls the
system. In this case the relay must be activated and the activation duration must be 2 seconds; after this the relay returns to the
previous status.
a) First of all Esim251 system relay output has to be connected to the connectors of automatic control unit.
b) The following configuration SMS message must be sent to Esim251 system:
XXXX_SMSEXTRA:COC:CE123,MS10,MS20,MS30,MS1T0.0.2,MS2T0.0.2,MS3T0.0.2
where CE123 means that C1 relay control via call is enabled for users NO1-NO3.
MS10 means that the relay is activated when user NO1 calls the system.
MS20 means that the relay is activated when user NO2 calls the system.
MS30 means that the relay is activated when user NO3 calls the system.
MS1T0.0.2 means that relay status is changed for 2 seconds when user NO1 calls the system.
MS2T0.0.2 means that relay status is changed for 2 seconds when user NO2 calls the system.
MS3T0.0.2 means that relay status is changed for 2 seconds when user NO3 calls the system.
24
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
3.9.1 Additional possibilities of configuring zones (inputs) alarm and restore
Initial factory default settings. During the alarm the system calls and sends SMS messages to all pre-programmed users until the first
successful SMS delivery or a call rejected by the user. The users are not notified about zone restore. Zone delay due to interference
is 600ms – i. e. only the impulse that is longer than 600ms is considered an event. All zones Z1-Z5 are enabled. Impulse counting
mode is turned off.
To change these settings send the followinf SMS message:
XXXX_SMSEXTRA:Zn:Value1,Value2,……,ValueN
XXXX – user password.
Zn – possible values Z1,Z2,Z3,Z4,Z5. Define the number of the zone that is changed.
Value structure is CnVal, where Cn means command name (2 letters), and Val-its value (digits without spaces or punctuation marks).
Value (CnVal) – Table of values
Cn – command
name (2 letters)
Val – possible
command
meaning.
SS
1,2,3,4,5
SC
1,2,3,4,5
CS
1,2,3,4,5
CC
1,2,3,4,5
SE
1,2,3,4,5
SD
1,2,3,4,5
CE
1,2,3,4,5
Alarm
configuration
Restore
configuration
CD
Input levels
1,2,3,4,5
Command description
During the alarm SMS
message will be sent to
users NO:1,2,3,4,5.
During the alarm SMS
message sending to
users No:1,2,3,4,5 will be
disabled.
During the alarm the
system will call users
No:1,2,3,4,5.
During the alarm calling
users No:1,2,3,4,5 will be
disabled.
During input restore SMS
message will be sent to
users No:1,2,3,4,5.
During input restore
SMS message sending is
disabled for No:1,2,3,4,5.
During input restore users
No:1,2,3,4,5 will be called.
During input restore
calling users No:1,2,3,4,5
is disabled.
0
Setting input type.
0 – NO (normally open).
1
Setting input type.
1 –NC (normally closed)
Initial factory
default values
Comments
SS12345
Enabled for all
users NO1-NO5.
E. g. SS25 means that during alarm SMS
message sending is enabled for users NO2
and NO5
E. g. SC2 means that SMS message sending
will be disabled for user NO2
CS12345 Enabled
for all users
NO1-NO5.
E. g. CC12345 means that during the alarm
none of the users will be called.
E. g. SE1 means that during zone reset SMS
message delivery is enabled for user No1
SD12345
Disabled for all
users NO1-NO5.
Impulse counting mode
is disabled
0
IE
1
Impulse counting mode
is enabled
IC
1- 4294967295
The number of impulses is
determined
LI0 Normally open
IE0 disabled
Pvz. IE0 means impulse counting mode is
disabled
DV
100-10000
Setting minimal input
impulse duration. It is
measured in milliseconds.
Impulse counting
Input protection
against
interference
USER MANUAL ELDES ESIM251 V1.0
E. g. SD45 means that during zone restore
SMS message sending is disabled for users
NO4 and NO5.
E. g. CE12 means that during input restore
calls are enabled for users NO1 and NO2
E. g. CD1345 means that when the input is
restored users NO1, NO3, NO4 and NO5 will
not be called.
Possibility to change input type, i. e. to
invert. E. g. LI0
It means that the input is considered
inactivated if there is no signal.
Possibility to change input type, i. e. to
invert.
E. g. LI1 means that input is in normal status
when the signal is transmitted. The event
appears only when the signal disappears.
CD12345
Disabled for all
users NO1-NO5.
LI
IE
E. g. CS124 means that during alarm calls are
enabled for users NO1, NO2 and NO4
DV600
Input counts impulses. The number of
impulses is defined by the command IC.
E. g. IE1
The alarm is activated when a preset
number of impulses is transmitted to the
input. E. g. IC100
In this case the alarm is activated when 100
impulses are sent to the input.
Maximum frequency is 5Hz.
The input is triggered only if the impulse
transmitted is not shorter than the preset
value. E. g. DV1000 means that the signal
transmitted to the input is shorter than
1000ms (1s) the alarm is not triggered.
25
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
ATTENTION!
Value fields are separated by commas. Maximum SMS length is 160 characters. Only one zone parameters can be configured by
one SMS message.
Examples of using SMSEXTRA command.
Suppose in all cases initial parameters were not changed and are manufacturer default.
1. Example of SMS message configuring Z1 input:
XXXX_SMSEXTRA:Z1:SC15,CC25,SE1234,CE4,LE1,DV900
This message configures Z1 input parameters.
SC15 means that during the alarm SMS message sending is disabled for users NO1 and NO5. As per manufacturer default settings
SMS sending is preset for all users, therefore users NO2, NO3 and NO4 SMS messages will still be delivered.
CC25 means that during the alarm calling function is disabled for users NO2 and NO5. As per manufacturer default settings, calling
function is preset for all users, therefore users NO1, NO3 and NO4 will still be called.
SE1234 means that SMS restore message sending is enabled for users NO1, NO2, NO3 and NO4. This means that when Z1 is restored
after previous trigger, these users will be informed about this restore by SMS message. However, alarms and restore SMS messages
will be sent until the first successful delivery. To enable compulsory message delivery to all users you should use the command
XXXX_SMSALL:ON, as described in chapter 3.7.
CE4 means that during Z1 restore only user NO4 is called.
LE1 means that input type for zone Z1 will be inverted, i. e. the previous NO is changed to NC (normally closed). This means that the
alarm is triggered only when the signal disappears, and the restore is announced only in the case when the signal appears.
DV900 means that Z1 input is triggered only if the signal is suspended at least for 900ms. Please note that input type was inverted
to NC. (If inversion was not possible this DV900 command would mean that the signal transmitted must not be shorter than 900ms.)
2. Example of SMS message configuring Z2 input:
XXXX_SMSEXTRA:Z2:IE1,IC555
This message configures Z2 input parameters.
IE1 means that impulse counting mode is enabled for Z2 input.
IC555 means that the users will receive the alarm when 555 impulses are transmitted to the input. Immediately after the alarm the
counter resets and starts counting impulses until their number reaches 555.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:Zn:Value1,Value2,……,ValueN
XXXX – user password.
Zn – possible values Z1,Z2,Z3,Z4,Z5. Define the number of the zone being changed.
Value structure is Cn, where Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:Z2:SS,SC,CC,SE,SD
26
ESIM 251
XXXX_
SMSEXTRA:
Z2:SS,SC,
CC,SE,SD
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
3.9.2 Additional possibilities of controlling and configuring controller C1 (relay output)
Normally C1 output can be controlled only by SMS message, as described in chapter 3.6, i. e. by enabling/disabling it for a permanent status or for a preset period. However, you can configure automatic enabling and disabling for a particular hour or control this
function by a call.
3.9.2.1 Settings of an output controlled by calls
When calling on the number of system Esim251 the call is rejected and no control operations are run. However, when a special
mode is enabled C1 output can be controlled by a call. It can be controlled by all users NO1-NO5, several users or only one of them.
By calling the system you can enable these 3 functions: enable/disable, enable/disable for a certain period or change output status
with every call, i. e. one call enables the status, the next one disables it etc.
The parameters are changed by sending the following SMS message to the system Esim251:
XXXX_SMSEXTRA:COC:Value1,Value2,……,ValueN
XXXX – user password. Value structure is CnVal, when Cn is command name (2 letters), and Val-its value).
Value (CnVal) – table of values
Cn – command Val – possible
name (2
command
letters)
meaning.
Confirmation
call duration
parameters
Enabling/
disabling
confirmation
SMS
(SMS confirm)
Control via call mode
is enabled for users
No:1,2,3,4,5
Control via call modes
is disabled for users
No:1,2,3,4,5
Initial factory
default values
1,2,3,4,5
CD
1,2,3,4,5
CS
1,2,3,4,5
Confirmation call
mode is enabled for
users No:1,2,3,4,5.
CC
1,2,3,4,5
Confirmation call
mode is disabled for
users No:1,2,3,4,5..
1,2,3,4,5;1; s
Confirmation call
is made for users
No:1,2,3,4,5 when the
ouput is turned on.
s- call time in seconds
СT112
СT212
СT312
СT412
СT512
1,2,3,4,5;0; s
Confirmation call
is made for users
No:1,2,3,4,5 when the
output is turned off.
s- call time in seconds
СT108
СT208
СT308
СT408
СT508
SS
1,2,3,4,5
Confirmation SMS
mode is enabled for
users No:1,2,3,4,5.
SC
1,2,3,4,5
Confirmation SMS
mode is disabled for
users No:1,2,3,4,5.
CD12345
Disabled for all
users NO1-NO5.
CC12345
Disabled for all
users NO1-NO5.
CT
USER MANUAL ELDES ESIM251 V1.0
Comments
E. g. CE25 means that users NO2 and NO5 will be
able to control the output via call.
CE
Enabling control
via call
Enabling/
disabling
confirmation call
(CallBack)
Command
description
SC12345
Disabled for all
users NO1-NO5.
E. g. CD25 means that output control via call is
disabled for users NO2 and NO5.
E. g. CS124 means that when users NO1, NO2 and
NO4 control the output via call they will be notified
about a successful output status change by a
confirmation call.
E. g. CC124 means that when users NO1, NO2 and
NO4 control the output via call the call confirming
about a successful output status change is disabled
and users will not receive calls.
The first number refers to user number. The second
number is a command and the last number refers
to call time in seconds.
E. g. СT412 means that if confirmation call mode
is enabled, user NO4 will receive a call if he/she is
trying to turn on the relay. The system will call for
2 seconds.
The first number refers to user number. The second
number is a command and the last number refers
to call time in seconds.
E. g. СT408 means that if confirmation call mode
is enabled, user NO4 will receive a call if he/she is
trying to turn off the relay. The system will call for
8 seconds.
E. g. SS124 means that when users NO1, NO2 and
NO4 control the output via call they will be notified
about a successful output status change by a
confirmation SMS message.
Before that the user has to turn on control from a
particular number by using CE command.
E. g. SC124 means that when users NO1, NO2 and
NO4 control the output via call the confirmation
SMS message informing about the successful
output status change is not sent.
27
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Type of control
via call
Setting relay
impulse
duration
MS
MS
1,2,3,4,5 and 0
When users
No:1,2,3,4,5 call the
output is enabled.
1,2,3,4,5 and 1
When users
No:1,2,3,4,5 call the
output is disabled.
1,2,3,4,5 and 2
When users
No:1,2,3,4,5 call
output status is
changed (TOGGLE)
1,2,3,4,5 and
Th.m.s
Setting relay impulse
duration for users
No:1,2,3,4,5. h- hours,
m- minutės, sseconds.
MS11
The first digit refer to user number. The second
digit refers to command. Therefore to set a
possibility for user NO1 to enable the relay via call
you have to use the command MS10
The first digit refer to user number. The second
digit refers to command. Therefore to set a
possibility for user NO1 to disable the relay via call
you have to use the command MS11
The first digits refer to user number. The last digit
refers to command. Therefore to set a possibility
for user NO1 to enable the relay by one call and
then disable it by the next call you have to se the
command MS12
E. g. to set the timer for 5 hours 10mins 3seconds
for user NO1 you have to use the command
MS1T5.10.3
This means that when afore mentioned user NO1
control the relay via call the impulse duration is
5hours 10mins and 3seconds and after this period
the relay returns to the previous status.
Example of SMS message configuring C1 output:
XXXX_SMSEXTRA:COC:CE1234,CS123,MS10,MS42,MS1T0.0.40
This message configures C1 output parameters.
CE1234 means that С1 output can be controlled by users NO1-NO4 (NO5 cannot control via call).
CS123 means that only users NO1, NO2 and NO3 will receive confirmation call.
MS10 means that when user NO1 calls the system he/she enables C1 input, but cannot disable it via call. The user can disable it via
SMS message if he/she knows the password.
MS42 means that when user NO4 calls the system he/she will either enable or disable output C1 (TOGGLE mode is on). It depends
on the relay status before making a call.
MS1T0.0.40 means that when user NO1 call the relay is turned on for 40seconds and then it automatically turns off.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value. This does not apply to MS and CT commands. When requesting MS and CT parameters MS and
CT must be followed by one character – user number (1,2,3,4 or 5).:
XXXX_SMSEXTRA:COC:Value1,Value2,……,ValueN
XXXX – user password. Value structure is Cn, where Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:COC:CE,CS,MS1,MS3
3.9.2.2 Settings of the output controlled by SMS messages
This chapter describes the ways of informing users when they are trying to enable/disable the relay via SMS messages described in
chapter 3.6. Parameters are changed by sending the following SMS message to system Esim251:
XXXX_SMSEXTRA:OCS:Value1,Value2,……,ValueN
XXXX – user password. Value structure is CnVal, where Cn is command name (2 letters), and Val-its value (digits without spaces or
punctuation marks).
28
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Value (CnVal) – table of values
Cn – command
name (2 letters)
Val – possible
command
meaning.
Command description
CB
1
Confirmation call mode
is enabled for all users.
CB
0
Confirmation call mode
is disabled for all users.
1; s
All users receive
confirmation call when
the output is enabled;
s- call time in seconds
0; s
All users receive
confirmation call when
the output is disabled;
s- call time in seconds
SB
1
Confirmation SMS
mode is enabled for
all users.
SB
0
Confirmation SMS
mode is disbled for all
users.
Enabling/
disabling
confirmation call
(CallBack)
Confirmation call
duration
Enabling/
disabling
confirmation
SMS message
(SMS confirm)
Initial factory
default values
Comments
CB1 means that when users control the
output via SMS message they are notified
about a successful output status change
by a confirmation call.
CB0
Disabled for all
users NO1-NO5.
CB0 means that when users control
the output via SMS message they will
not receive a call informing about a
successful output status change.
СT12
The first digit is a command; the last digit
refers to call time in seconds. E. g. СT12
means that if confirmation call mode is
enabled the call will be forwarded to the
user who is trying to turn on the relay.
The system will call for 2 seconds.
СT08
The first digit is a command; the last digit
refers to call time in seconds. E. g. СT08
means that if confirmation call mode is
enabled the call will be forwarded to the
user who is trying to turn off the relay.
The system will call for 8 seconds.
CT
SB1
Enabled for all
users NO1-NO5.
SB1 means that when all users control
the output via SMS message they will
be informed about a successful output
status change by a confirmation SMS
message.
SB0 means that when all users control
the output via SMS message they will not
be informed about a successful output
status change by SMS message.
Example of SMS message configuring C1 output ways of information:
XXXX_SMSEXTRA:OCS:CB1,CT13,CT06,SB1
This message configures C1 output parameters when controlled via SMS messages.
CB1 means that when the user enables/disables output С1 he/she receives ashort confirmation call CALLBACK.
CT13 means that when the relay is enabled confirmation call duration is 3 seconds.
CT06 means that when the relay is disabled confirmation call duration is 6 seconds.
SB1 means that confirmation message is sent informaing about enabling/disabling.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:OCS:Value1,Value2,……,ValueN
XXXX – user password. Value structure is CnVal, when Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:OCS:CB,CT,SB
USER MANUAL ELDES ESIM251 V1.0
29
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
3.9.2.3
Output ontrol settings by event time
This chapter describes a possibility to control C1 output (relay) using timetable (schedule). It can be, for instance, atomatic turning
on every day at 18:00 and turning off after 5 hours.
The parameters are changed by sending the following SMS message to the system Esim251:
XXXX_SMSEXTRA:OCTE:Value1,Value2,……,ValueN
XXXX – user password. Value structure is CnVal, when Cn is command name (2 letters), and Val-its value.
Value (CnVal) – table of values
Cn – command
name (2
letters)
Val –
possible
command
meaning.
h.m
Setting enabling/
disabling time
WT
Command
description
Initial factory
default values
Comments
h hour m
minutes
Indicates the time for
enabling or disabling
C1 output in hours
and minutes
E. g. WT18.10 means event start time. It can be
enabling and disabling. It depends on the set
ST value. A period PT must also be indicated,
otherwise relay status will not change. See below.
1
Relay is enabled
0
Relay is disabled
E. g. ST0 means that when the set time comes the
relay is disabled by WT command.
h.m
Indicates the time in
hours and minutes for
which C1 relay status
is changed.
E. g. PT1.20 means that after automatic enabling/
disabling which is indicated in WT command relay
status is changed to opposite for 1 hour and 20
minutes.
1
Users are notified
about period start by
a confirmation call
CS1 means that the preset user is informed about
the period start of C1 output enabling or disabling
via short call. The user is set by using UC command.
See below.
0
Users are not notified
about period start by
a confirmation call
1
Users are notified
about period end by a
confirmation call
0
Users are not notified
about period end by a
confirmation call
1; s
The user receives
a confirmation call
when the output is
enabled;
s- call time in seconds
ST1
Setting relay
status, whether
it is enabled or
disabled
Setting the period
of enabling/
disabling
Setting
confirmation call
for period start
Setting
confirmation call
for period end
Confirmation call
duration
30
ST
PT
h hour m
minutes
Relay is
enabled
E. g. ST1 means that when the set time comes the
relay is enabled by WT command.
CS
СS0
Call is not
made
CS0 means that nobody is informed about period
start by a call.
CE1 means that the preset user is informed about
the period end of C1 output enabling or disabling
via short call. The user is set by using UC command.
See below.
CE
CT
СE0
Call is not
made
СT12
CE0 means that nobody is informed about period
end by a call.
The first digit is a command; the last digit refers
to call time in seconds. E. g. СT12 means that if
confirmation call mode is enabled, whether for
period start ot end, the call will be forwarded to
the user when relay is enabled. The system will call
for 2 seconds.
EN
F O R A D VA N C E D U S E R S
All these features can be configured using program Esim251 ConfigTool.
Setting the user
who receives
confirmations
about period
start/end
Setting
confirmation
SMS message for
period start
Setting
confirmation
SMS message for
period end
UC
0; s
The user receives
a confirmation call
when the output is
disabled;
s- call time in seconds
СT08
The first digit is a command; the last digit refers to
call time in seconds.
E. g. СT08 means that if confirmation call mode
is enabled, whether for period start ot end, the
call will be forwarded to the user when relay is
disabled. The system will call for 8 seconds.
1,2,3,4,5
Sets which user is
notified about period
start/end.
UC1
E. g. UC2 means that all confirmations will be
delivered to user No2.
Only one user can be selected.
1
Users are notified
about period start by
SMS message
0
Users are not notified
about period start by
SMS message
1
Users are notified
about period end by
SMS message
0
Users are not notified
about period end by
SMS message
SS
SE
SS1 means that the preset user is notified about
period start of enabling/disabling C1 output
by SMS message. The user is set by using UC
command. See below.
SS0
SS0 means that nobody is informed about period
start by SMS message.
SE1 means that the user is also notified about relay
disabling by SMS message.
SE0
SE0 means that nobody is informed about period
end by SMS message.
Example of SMS message configuring C1 output ways of information by preset schedule:
XXXX_SMSEXTRA:OCTE:WT20.15,ST1,PT8.0,UC2,CS1,CT13,CT06,SE1
This message configures C1 output parameters using a schedule.
WT20.15 means that relay enablig time is set for 20:15 every day.
ST1 means the user set the relay to turn on on that time.
PT8.5 means that the relay is enabled and is on for 8 hours and 5 minutes, and after that it turns off and turns on again at 20:15 the
following day etc.
UC2 means that information about enabling/disabling is sent to user’s No2 telephone.
CS1 means that the user is notified about relay enabling by a callback; the duration of the call is set by parameter CT13. CT13 means
that the system calls for 3 seconds.
CT06 means that when the relay turns off after 8 hours and 5 minutes the user is notified by a call again, but call duration is 6
seconds.
SE1 means that the user is also notified about relay enabling by SMS message.
To see the preset values for any command send SMS message with the same format that you use when changing parameters; only
Value structure will have no value:
XXXX_SMSEXTRA:OCTE:Value1,Value2,……,ValueN
XXXX – user password. Value structure is Cn, where Cn is command name (2 letters).
E. g. XXXX_SMSEXTRA:OCTE:CB,CT,SB
USER MANUAL ELDES ESIM251 V1.0
31
4. Appendix
4.1 Restoring Default Parameters
To restore default parameters:
•
disconnect power supply and USB connector
•
short circuit (connect) connectors D1 and D2
•
connect power supply for 5 seconds
•
disconnect power supply
•
disconnect connectors D1 and D2
4.2 Esim251 ConfigTool configuration software
To configure the system quicker and easier as well as use more system capabilities use configuration program „Esim251 ConfigTool” which can be downloaded from our website www.eldes.lt
Before connecting USB cable to the computer read Esim251 ConfigTool user guide available in the program chapter HELP.
4.3 Technical Support
Indication
Indicator is off or not blinking
Possible reason
· no external power supply
· circuit not properly connected
· blown fuse
· no network signal
Indicator blinking several times per · SIM card is not inserted
second
· PIN code hasn’t been disabled
· Sim card not active
System does not send any SMS
· SIM card account depleted
messages and/or does not ring
· incorrect SIM central number
· no network signal
· user number is not programmed
(or disabled access from unknown numbers)
Received SMS message “Incorrect
· incorrect syntax
Format”
· extra space symbol left in SMS message
No sound while listening to remote · microphone not connected
microphone
· microphone connection incorrect
While listening to remote micropho- · Change the position of the microphone or its lead in
ne outside noise heard
respect of system panel
If your problem could not be fixed by the self-guide above, please contact your distributor or manufacturer tech support by email
[email protected] More up to date information about your device and other products can be found at the manufacturer’s website
www.eldes.lt
32
EN
USER MANUAL ELDES ESIM251 V1.0
33
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement