U-Line | CO2175DWR | Troubleshooting guide | U-Line CO2175DWR Troubleshooting guide

U-Line CO2175DWR Troubleshooting guide
ULIN_016357_30095.fm Page 1 Wednesday, February 7, 2007 12:44 PM
Use and Care Guide
Combo® Drawer Model:
CO2175DWR
CO2175DWR
1 Introduction
Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line
Corporation is the world’s number one manufacturer of built-in, under-counter, specialty refrigeration and ice making
products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology
consistently leads the market with innovation, design, depth of product line and performance.
U-Line products are making life more convenient in homes, businesses, and hotels around the world. U-Line supports its
products with a strong dealer network, and its commitment to quality even extends to environmentally safe packaging.
IMPORTANT
READ all of the instructions in this guide completely before operating the unit for the first time.
For future reference, keep this guide in a safe, accessible location. If you need additional information or assistance,
please contact U-Line Corporation directly. Contact information appears on the rear cover of this guide.
If you have a problem with the operation of this product, the SERVICE section of this guide will assist you in quickly
identifying common problems and provide information on possible causes and remedies. If your product needs service,
contact U-Line directly.
Warranty Registration
Your U-Line Corporation Limited Warranty is located on the inside rear cover of this guide. To validate your warranty, the
product and its original purchase date must be registered. A Warranty Registration Card has been included for this
purpose in the package containing this manual. Complete and mail the Warranty Registration Card, or register your
product online at www.U-LineService.com as soon as possible after purchase.
If your product registration is not on file and a request for warranty coverage is received, the date of sale to the U-Line
Selling Dealer or Distributor will be established as the first date of warranty coverage for your product.
Please Record Your Model Information
When you request additional information or service, you will be asked for your products model and serial numbers. You
can find this information on the serial plate located on the upper right or rear wall in the interior of your unit. This
information also appears on the warranty registration card.
2
1
ULIN_0023_A
Figure 1
Please record the model number (Figure 1, 1), serial number (Figure 1, 2), date of purchase, and dealer contact
information for your U-Line product below:
Model Number:
Dealer Name:
_____________________________________________________
_____________________________________________________
Serial Number:
Dealer Address:
_____________________________________________________
_____________________________________________________
Purchase Date:
Dealer Telephone:
_____________________________________________________
_____________________________________________________
2
CO2175DWR
2 Table of Contents
Introduction ...............................................................................................................................2
Warranty Registration .......................................................................................................2
Please Record Your Model Information ...........................................................................2
Table of Contents .......................................................................................................................3
Safety Precautions ......................................................................................................................5
Safety Alert Definitions .....................................................................................................5
General Precautions ...........................................................................................................5
Product Features ........................................................................................................................6
Échelon Drawer Combo Refrigerator, Freezer, Ice Maker Model CO2175DWR ............6
Operation ...................................................................................................................................7
Initial Start-up ....................................................................................................................7
Interior Lighting .................................................................................................................7
Electronic Control Panel ....................................................................................................7
Ice Maker ............................................................................................................................8
Normal Operating Sounds .................................................................................................9
Food Storage ....................................................................................................................10
Storage, Vacation, Moving ..............................................................................................11
Product Disposal ...............................................................................................................11
Cleaning and Maintenance .....................................................................................................12
General Cleaning .............................................................................................................12
Maintenance ....................................................................................................................12
Service .......................................................................................................................................15
Before Calling for Service ................................................................................................15
If Service is Required ........................................................................................................15
Replacement Parts ...........................................................................................................15
Troubleshooting Guide ....................................................................................................16
Electronic Control Quick Guide .......................................................................................18
U-Line Corporation Limited Warranty ....................................................................................19
CO2175DWR
3
This page intentionally left blank
4
CO2175DWR
WARNING
3 Safety Precautions
• PLEASE READ all instructions completely before
attempting to install, operate, or service your
unit.
• Proper installation procedures must be followed
if this unit is being initially installed, or is moved
to a new location after being in service. An
INSTALLATION GUIDE for your unit, providing
complete installation information is available
from U-Line Corporation directly, and must be
consulted before any installation is begun. U-Line
contact information appears on the rear cover of
this guide.
• This unit requires connection to a grounded
(three-prong), polarized receptacle that has been
placed by a qualified electrician in accordance
with applicable electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform
maintenance on the unit until the electricity
has been disconnected.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Altering, cutting of power cord, removal of
power cord, removal of power plug, or direct
wiring can cause serious injury, fire and/or loss
of property and/or life, and will void the
warranty.
• Never use an extension cord to connect power
to the unit.
• Always keep your working area dry.
WARNING
The Anti-Tip Kit must be installed on this unit
before it is used. Never use the drawers as steps
or as a shelf to support more than the drawers’
contents. Serious personal injury could occur.
DANGER
CAUTION
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
CAUTION
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away
your old refrigerator or freezer, take off the doors
and leave shelves in place so that children may not
easily climb inside.
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp
edges.
• If your model requires defrosting, DO NOT use any
type of heater to defrost. Using a heater to speed
up defrosting can cause personal injury and
damage to the inner lining.
IMPORTANT
• Do not lift unit by drawer handles.
• Never install or operate the unit behind closed
doors. Be sure front grille is free of obstruction.
Obstructing free air flow can cause the unit to
malfunction and may void the warranty.
• Failure to clean the condenser every three months
can cause the unit to malfunction. This could void
the warranty.
• Allow unit temperature to stabilize for 24 hours
before use.
• If your model requires defrosting, never use an
ice pick or other sharp instrument to help speed
up defrosting. These instruments can puncture
the inner lining or damage cooling unit.
• Use only genuine U-Line replacement parts.
Imitation parts can damage the unit, affect its
operation or performance and may void the
warranty.
CO2175DWR
5
• Full wrap stainless steel drawers with sculpted handles
distinguish this unit from heavier, “commercial” looks.
4 Product Features
• The top drawer features a stainless steel interior that is
corrosion-resistant and provides a sleek, professional
appearance.
Échelon Drawer Combo
Refrigerator, Freezer, Ice Maker
Model CO2175DWR
• Heavy duty, full extension drawer slides permit easy
accessibility to contents in the back of drawers.
A FROST FREE 5.0 cu ft (142 L) combination refrigerator/
freezer/ice maker
Features of Échelon
• Approximately 3.0 cu ft (85 L) of refrigeration capacity
is available in the top drawer, and approximately 2.0 cu
ft (57 L) of freezer capacity is available in the bottom
drawer.
• The ice maker will produce up to 6 lbs (2.7 kg) of ice
per day and store up to 10 lbs (4.5 kg) in the ice bucket.
• The freezer drawer can be maintained between -5°F
and +5°F, providing temperatures ideally suited for
storage of ice cream products.
• Frost Free technology eliminates the need for manual
defrosting.
• An electronic control panel with digital display allows
you to display the actual temperature in each drawer,
and adjust the individual temperature in the top
refrigerator drawer between 34°F and 45°F. The
electronic control and digital display provide an
attractive appearance, and its method of control
provides precise temperature settings.
• All units feature a black vinyl clad steel cabinet that
provides a rich textured look, and resists scratching,
peeling and flaking.
• Black units come standard from the factory equipped
for full overlay panels. However, the drawers can
accommodate custom 1/4" (0.64 cm) thick panels.
NOTE: If neither full overlay nor 1/4" (0.64 cm) thick
panels will be used, U-Line recommends replacing the
existing handles with the replacement drawer handles
(P/N 26070-01).
• The Model CO2175DWR unit cannot be configured for
a free-standing installation. It must be installed as a
built-in, under counter unit, and be anchored to
prevent tipping using the originally provided anti-tip
kit.
Features and specifications are subject to change without
notice.
• Multiple organizing features allow you to customize
your refrigeration space, including:
a. An adjustable Slide and Divide organizer comes
standard in the top drawer and can be easily
adjusted from front to back and side to side.
b. A clear organizing bin in the top drawer can
accommodate wine bottles, two-liter bottles or
other items. The bin is designed to slide from the
front to rear of the drawer, allowing easy access to
items in or beneath the bin.
6
CO2175DWR
Interior Lighting
5 Operation
The interior drawer lights are controlled by individual
switches on each drawer. As a drawer is opened, the light
will go ON. The light will go OFF when the drawer is
closed.
The LIGHT icon (Figure 3, 5) on the control panel is used
to control an additional lighting function. The blackout/
Sabbath mode (not Star K certified) will turn the interior
lights and display (Figure 3, 3) off for a preset 36-hour
period.
ULIN_0080_A
To access the blackout/Sabbath mode (not Star K
certified):
Figure 2
IMPORTANT
Proper air flow is required for your unit to operate
at its highest efficiently. A grille, located in the base
of the unit, must not be blocked at any time, or
your unit will not perform as expected (Figure 2).
Initial Start-up
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
IMPORTANT
• U-Line recommends the unit be allowed to run
overnight and make ice prior to loading the
refrigerator and/or freezer with product.
• It is possible that dirt or scale will dislodge in the
water line. Always throw away all ice cubes made
during the first two to three hours of operation.
1
2
3
4
1. Touch and hold the LIGHT icon (Figure 3, 5) for ten
seconds and release (the °F symbol will flash briefly at
the end of the ten second period).
2. The interior light and control display (Figure 3, 3) will
go dark for the next 36 hours.
NOTE: Although the display will not be visible, the
temperature controls in the unit remain active, and the
interior temperature will be maintained.
3. To exit the blackout/Sabbath mode (not Star K
certified) manually at any time, repeat Step 1.
Electronic Control Panel
1
2
3
5
4
5
ULIN_0058_A
Figure 4
ULIN_0058_A
Figure 3
NOTE: The controller for the drawer is located in the top
drawer.
To turn the unit on or off, touch and hold the POWER icon
(Figure 3, 1) on the display panel for approximately ten
seconds until the °F symbol flashes and release.
• A small LED above the icon will illuminate to confirm
the touch of any controller icon.
• The display (Figure 3, 3) will show the unit set-point
temperature (38°F) when the unit is on and will show
OFF when the unit is off.
• Turning the unit off will override any other control
function.
The electronic control with digital display (Figure 4) is
configured to show a single temperature continuously.
This set-point temperature is a base number used by the
controller to maintain the temperature zone in your unit.
The factory default set-point is 38°F. This set-point
temperature is used as a gauge if further temperature
adjustments are required.
Temperature Display Selection
U-Line products supplied for 110 VAC operation have
temperatures displayed in a default Fahrenheit (°F)
configuration (Figure 4, 3). Models supplied for 220 VAC
operation have temperatures displayed in a default
Celsius (°C) configuration.
The display can easily be adjusted for either type of
temperature display. Press and hold the LIGHT icon
(Figure 4, 5) and within five seconds press the COOLER
icon (Figure 4, 4) three times to change the display as
desired.
CO2175DWR
7
Temperature Display
Ice Maker
To display the interior temperature:
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
to cool and maintain the cube supply. Frost-free icemaker
units have lower ice production than manual defrost
units.
1. Touch and hold the WARMER icon (Figure 4, 2) for
approximately five seconds and release when the °F
symbol in the display (Figure 4, 3) begins to flash.
2. The display (Figure 4, 3) will indicate the actual
refrigerator temperature.
3. After approximately 10 seconds, the set-point
temperature will return to the display.
Factors which affect the internal temperatures of the
cabinet include:
• Temperature setting.
• Ambient temperature where installed.
• Number of times and length of time the door is
opened and closed.
ULIN_0087_A
• Installation in direct sunlight or near a heat source.
Adjusting Temperature
NOTE: The top drawer refrigerator section temperature is
adjustable. The bottom drawer freezer temperature is not
adjustable.
IMPORTANT
Adjust the set-point temperature in single
increments, and wait 24 hours for the temperature
to stabilize before rechecking.
1
2
3
4
Figure 6
Ice production may be interrupted by raising the bin arm
into an upright and locked position (Figure 6). The unit
will maintain temperature for ice storage.
IMPORTANT
If you are not intending to use the ice maker and
turn the supply valve off, it is imperative to raise
the bin arm of the ice maker (Figure 6). Failure to
raise the bin arm may result in damage to the water
valve.
Certain sounds are normal during the unit’s operation.
You may hear the compressor or fan motor, the water
valve, or ice dropping into the ice bucket.
5
WARNING
ULIN_0058_A
NEVER use an ice pick, knife, or other sharp
instrument to separate cubes. Shake the ice
bucket instead.
Figure 5
To adjust the set-point temperature:
1. Press and release either the WARMER (Figure 5, 2) or
COOLER (Figure 5, 4) icon to put the controller in the
SET TEMPERATURE mode. The °F symbol (Figure 5, 3)
will begin to flash.
During periods of limited usage or high ambient
temperatures, it is common for cubes to fuse together.
Shake the bucket to break apart cubes. If the ice maker is
not used regularly, the ice bucket should be emptied
periodically to ensure fresh cubes.
NOTE: If no further action is taken, this mode will self
cancel in five seconds, and the original set-point
temperature will be displayed.
2. While the °F symbol is flashing, press the WARMER or
COOLER icon as required to adjust the set-point
temperature.
3. The change will be set five seconds after adjusting the
temperature and the new set-point temperature will be
displayed.
8
CO2175DWR
It is normal for cubes to appear cloudy. This is caused by
air being trapped in the water due to fast freezing. It has
nothing to do with the health, taste or chemical make-up
of the water. It is the same air that is in every glass of
water you drink.
Do not place cans or bottles in the ice compartment,
because they will freeze.
Normal Operating Sounds
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. In spite of
this technology, your model may make sounds that are
unfamiliar.
Normal operating sounds may be more noticeable
because of the unit’s environment. Hard surfaces such as
cabinets, wood/vinyl/tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
1
Common refrigeration components, and a brief
description of the normal operating sounds they make,
are listed below. NOTE: Your product may not contain all
of the components listed.
• Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
• Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
• Condenser Fan: Air moving through a condenser may be
heard.
ULIN_0083_A
Figure 7
The ice bucket can be removed for emptying and
cleaning. To remove ice bucket, open drawer fully, then
grasp the sides of the ice bucket and lift straight up
(Figure 7, 1). Use the ice bucket for ice storage only.
NOTE: It is recommended that if ice bucket is removed for
any reason, the bin arm on the ice maker should be raised.
If bin arm is not raised, the ice maker can harvest ice and
will drop ice behind lower drawer.
• Automatic Defrost/Drain Pan: Water may be heard
dripping or running into the drain pan when the unit is in
the defrost cycle.
• Ice dropping into ice bucket
An accessory ice bucket (U-Line P/N 26014) can be
purchased and placed next to the provided ice bucket.
When two ice buckets are used, the ice buckets can be
rotated for increased ice storage.
CO2175DWR
9
Food Storage
Drawers
The drawers should only be removed for servicing by a
trained and certified repair person.
Top Storage Bin
When adjusting the organizer, open the drawer fully,
remove the bin and all other items, and brace the drawer
to prevent movement. To adjust, turn the drawer
organizer knob (Figure 9, 1) counterclockwise to loosen
and use two hands to position as desired. Tighten knob
after adjustment is made. Do not over-tighten.
Clean the drawer organizer with warm water and a mild
detergent only. Do not use solvent based or abrasive
cleaners and do not place the drawer organizer in a
dishwasher.
1
1
ULIN_0086_A
Figure 8
Grasp the bin handle and slide backward to access the
contents below (Figure 8). The bin may be completely
removed for cleaning once it is slid forward, making sure
it clears the guides on each side of the drawer. Then lift
straight up. If heavy items are stored in bin, push front of
bin down slightly while sliding. Slide bin forward,
especially with heavy items, to ensure that drawer closes
completely.
Drawer Organizer
Adjust the drawer organizer to compensate for different
size bottles or items. The organizer can be used in the top
drawer only.
ULIN_0089_A
Figure 10
Be sure that items stored in the rear of the top drawer do
not interfere with the sliding operation of the storage
bin. Tall items such as milk jugs can be stored toward the
front of the drawer as long as they do not interfere with
the closing of the drawer. Taller items can be stored on
their side (Figure 10, 1) in the storage bin.
The storage bin is designed to accommodate the storage
of two wine bottles, even when opened.
Place the bottle in the bin so that the neck of the bottle
rests on the front lip of the bin.
1
ULIN_0084_A
Figure 9
The organizer may be adjusted left-to-right or front-toback as required.
10
CO2175DWR
Storage, Vacation, Moving
Product Disposal
If the unit will not be used for an extended period, or
otherwise stored, follow these steps completely:
If the unit is being removed from service for disposal,
check and obey all Federal, State and/or Local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
WARNING
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels.
Failure to do so may result in death or electrical
shock.
1. Remove all consumable contents from the unit.
2. Shut off water supply to the unit at the main water
source.
IMPORTANT
• If the ambient temperature is expected to drop
below 45°F, turn off and unplug unit, and drain all
water from the unit to prevent freezing damage
not covered by the warranty.
• The use of anti-freeze or other products of this
nature is not necessary and is not recommended.
1. Remove all consumable contents from the unit.
2. Disconnect power to the unit and unplug the power
cord from its outlet.
3. Shut off water supply to the unit at the main water
source and disconnect the supply line to the unit’s water
valve.
DANGER
RISK OF CHILD ENTRAPEMENT. Before you throw
away your old refrigerator or freezer, remove the
drawers.
4. Remove the drawers from the unit, and secure all
shelving and accessories to the interior of the unit using
a heavy duty cloth or package sealing tape.
3. Disconnect the water valve inlet and outlet lines, and
allow them to drain completely.
4. Reconnect power to the unit, and allow it to run for
one hour (minimum) until any remaining ice has been
ejected from the ice maker assembly.
5. Disconnect power to the unit, dry any remaining water
from the ice maker assembly, and reconnect any lines
removed from the water supply valve.
6. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
7. Clean and dry the interior of the cabinet (See CLEANING
AND MAINTENANCE: GENERAL CLEANING).
8. During periods of non-use, the cabinet must remain
open to prevent the formation of mold and mildew.
Open door a minimum of 2" (5 cm) to provide the
necessary ventilation.
CO2175DWR
11
Maintenance
6 Cleaning and Maintenance
Proper maintenance of your U-Line product will ensure
efficiency, top performance and long life. The
maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if you
have pets or other special considerations.
General Cleaning
Exterior Cleaning (As Required)
Black Models:
• Surfaces may be cleaned with a mild detergent and
warm water solution. Do not use solvent-based or
abrasive cleaners. Use a soft sponge and rinse with
clean water. Wipe with a soft, clean towel to prevent
water spotting.
Defrosting
Frost-Free Models
Frost-free models do not produce frost in normal
operating conditions.
WARNING
Stainless Steel Models:
• Stainless steel surfaces and components can discolor
when exposed to chlorine gas, pool chemicals, salt
water or cleaners with bleach.
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire®
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation (P/N 173348).
Comparable products are acceptable. Frequent
cleaning will remove surface contamination that could
lead to rust. Some installations may require cleaning
on a weekly basis.
DO NOT use any type of electrical heating device,
ice pick, knife or other sharp instrument to
defrost; this could damage the inner lining or
refrigeration system and void the warranty.
Condenser Cleaning
Interval - Every Three Months
To maintain operational efficiency, keep the front grille
free of dust and lint and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
WARNING
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel on stainless steel
surfaces (this includes glass, tile and counter
cleaners).
Disconnect electric power to the unit before
cleaning the condenser.
• If any surface discoloring or rusting appears, clean it
quickly with Bon-Ami® or Barkeepers Friend Cleanser®
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
To remove and replace the grille for access to the
condenser fins, follow this procedure:
2
• Using abrasive pads such as Scotchbrite™ will
cause the graining in the stainless steel to
become blurred.
1
• Rust that is not cleaned up promptly can penetrate into
the surface of the stainless steel and complete removal
of the rust may not be possible.
Figure 11
1. Disconnect electrical power to the unit.
Interior Cleaning (As Required)
• Disconnect power to the unit. Clean the interior and all
removed components using a mild non-abrasive
detergent and warm water solution applied with a soft
sponge or non-abrasive cloth. Rinse the interior using a
soft sponge and clean water.
• Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transmit
taste to the interior products and damage or
discolor the interior.
2. Loosen two screws (Figure 11, 1) completely.
NOTE: Screws are held in the grille by o-ring retainers,
and will not come free of the grille.
3. Remove the grille.
WARNING
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
IMPORTANT
Do not place top storage bin, drawer organizer or
the crisper bin in dishwasher. Dishwasher will warp/
discolor items and render them useless.
12
ULIN_0258_A
CO2175DWR
CAUTION
DO NOT use any type of cleaner on the condenser
unit.
4. Clean the condenser coil (Figure 11, 2) using a soft
brush with a “combing” action or vacuum cleaner. Do
not touch the condenser coil.
5. Position the grille to align the mounting screws with
the holes in the cabinet.
ULIN_0259_A
6. Secure, but do not over-tighten both grille screws.
Figure 13
7. Reconnect power to the unit.
1. Remove the ice maker assembly cover (Figure 13).
Ice Maker Maintenance
Inlet Screen
Interval - Every Twelve Months
The solenoid valve inlet screen must be cleaned at least
once each year as follows:
1. Shut off the water at the main supply valve.
2. Pull the unit out to access the back panel.
3. Disconnect electrical power to the unit.
2
ULIN_0056_A
Figure 14
2. Locate the adjusting screw on the ice maker assembly
control box. The adjusting screw is just below the minus
(-) and plus (+) signs on the control box (Figure 14).
1
NOTE: Make adjustments in small increments. Too
large of an adjustment could cause the unit to
malfunction.
ULIN_0054_A
Figure 12
4. Disconnect the hose connector (Figure 12, 1) from the
water solenoid valve (Figure 12, 2).
5. DO NOT remove the inlet screen from the water
solenoid valve. Use a tooth brush to gently clean any
sediment from the inlet screen.
6. Re-connect the water supply hose connector (Figure
12, 1) to the water solenoid valve (Figure 12, 2).
Tighten the connector securely.
7. Open the water main supply valve and check for
leakage at the water hose connection. Ensure that the
water supply line is not kinked.
8. Reconnect power to the unit before re-installing.
Ice Cube Thickness Adjustment
Interval - As Required
On ice maker equipped models, the cube size may be
adjusted by changing the amount of water injected into
the ice maker assembly as follows:
CAUTION
Too large of an adjustment to the screw can cause
the water to overflow the ice maker and can cause
property damage.
3. Turn the adjusting screw toward the minus (-) sign
(clockwise) for smaller cubes or toward the plus (+) sign
(counterclockwise) for larger cubes.
4. Install the ice maker assembly cover.
IMPORTANT
Use only genuine U-Line replacement parts. U-Line
ice maker parts are not the same as standard FSP
Whirlpool parts. Using non U-Line parts can reduce
ice rate, cause water to overflow from ice maker
mold, damage the unit, and may void the warranty.
CO2175DWR
13
Leveling
Light Bulb Replacement
NOTE: It is important that the unit is level. If unit is not
level, the ice mold may not fill evenly.
To replace the light bulb in your U-Line unit:
1
2
ULIN_0001_A
Figure 17
1. Grasp the edges of the light housing lens
(Figure 17, 1) opposite the exposed tab and gently
push the lens toward the tab (Figure 17, 2).
2. Pull the edge of the lens down (Figure 17, 1) and
swing it out of the light housing.
ULIN_0045_A
IMPORTANT
Figure 15
1. Use a level to check the levelness of the unit from
front to back and from side to side. Place the level
along top edge and side edge as shown (Figure 15).
ALWAYS use a genuine U-Line replacement bulb (P/N
31317) in the light housing. Use of any other bulb
within the housing will generate excessive heat,
causing damage to the light housing and cabinet
interior, and will compromise the precise
temperature control of your unit.
3. Replace the bulb only with a genuine U-Line P/N 31317
replacement.
4. Replace the lens by first inserting the tab side back into
the housing at a slight angle. While gently pushing the
lens towards the tab end, push the free end up into the
housing, and release when you will hear a snap/click.
ULIN_0046_A
Figure 16
2. If the unit is not level, adjust the feet on the corners of
the unit as necessary (Figure 16).
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level.
14
CO2175DWR
7 Service
Before Calling for Service
If your U-Line product appears to be malfunctioning, read
through the OPERATION section of this guide to ensure
that the function of all controls are clearly understood. If
the malfunction persists, the TROUBLESHOOTING GUIDE
in this guide will assist you in quickly identifying common
problems, and provide information on possible causes and
remedies. Most often, this will resolve the problem
without the need to call for service.
If Service is Required
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
Replacement Parts
When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
durability of your product, and may also void its warranty.
CO2175DWR
15
Troubleshooting Guide
DANGER
ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
Troubleshooting - What to check when problems occur:
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit does not operate and
electronic display is blank.
No electrical supply
Plug unit in or check circuit breaker.
No interior light.
Loose or burned out bulb.
Tighten or replace bulb (See MAINTENANCE; LIGHT
BULB REPLACEMENT).
Electronic display is blank and
Unit is in blackout/Sabbath mode
interior light is OFF with door OPEN. (not Star K certified).
Exit blackout/Sabbath mode (not Star K certified)
(See OPERATION; INTERIOR LIGHT CONTROL).
Electronic display is blank and
interior light is ON with door OPEN.
A display function has changed.
Touch and hold the warmer temperature button and
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
Electronic display shows repeating,
randomly flashing symbols and
partial characters.
A factory control mode has been
inadvertently entered.
Touch and hold the warmer temperature button and
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
Electronic display shows:
0, 1 to 26, or 99.
A factory control mode has been
inadvertently entered.
Repeatedly touch the warmer temperature button to
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
Electronic display shows E3 or E10.
Drawer(s) open longer than 20
minutes
Close drawer(s) completely. The set-point temperature
should now be displayed.
Electronic display shows one or
more of the following:
E1, E2, E4, E5, E6, E7, E8, E9, E11, P1.
The unit is displaying an error code.
Record the error code(s) displayed and call for service.
Unit not cold enough. Check
temperatures (See OPERATION for
approximate temperatures).
Control set too warm
Set control to a cooler setting (See OPERATION). Allow
24 hours for temperature to stabilize.
Airflow to front grille blocked
Airflow must not be obstructed to front grille (See
OPERATION).
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Door gasket not sealing properly
Door adjustment required (See MAINTENANCE; DOOR
ALIGNMENT CHECK AND ADJUSTMENT).
Item(s) interfering with drawer
closing
Reposition or remove item(s).
Inaccurate temperature reading
Properly check temperature (See OPERATION).
Drawer(s) not closed
Be sure drawer(s) is closed correctly.
Drawer(s) not closed correctly
Be sure drawer(s) is closed correctly.
Drawer(s) not closed correctly
Be sure drawer(s) is closed correctly.
Temperature control set too cold
Set temperature controller to warmer setting (See
OPERATION). Allow 24 hours for temperature to
stabilize.
Inaccurate temperature reading
Properly check temperature (See Operation).
Freezer section too warm
Fresh food section too cold
16
CO2175DWR
PROBLEM
POSSIBLE CAUSE
REMEDY
Noise during operation
Copper water supply tubing
contacting internal components
Carefully bend tubing away from cabinet and
components.
Certain sounds are normal.
Soft sounds from the fan and water/dropping sounds
from the ice maker will be heard.
Item(s) interfering with drawer
closing
Adjust items in drawer(s).
Drawer(s) can't close.
Unit not level
Make sure unit is level. (See LEVELING, page 14.)
Water is leaking out the back of the
unit.
Water supply connection leaking
Tighten fitting as required.
Ice cubes sticking together
Infrequent use of cubes
Break apart cubes.
No ice
Bin arm locked in upright position
Lower bin arm.
No water to unit
Turn on water or contact plumber.
Ice cube size too large
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUSTMENT).
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Water level set too high
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUSTMENT).
Not enough ice
Water leaks into ice bucket.
CO2175DWR
17
Electronic Control Quick Guide
All Models
Task
Touch
Turn ON/OFF
Adjust
Temperature
Hold 10 seconds
Touch
Display
Release when °F flashes.
or
or
or
Touch and release
Touch to change temperature
View Actual
Temperature
Hold 5 seconds
Change °F-°C
Hold
Blackout
Mode
°F flashes after first touch,
set-point saved after 5
seconds of inactivity and °F
stops flashing.*
For Wine Coolers, see Use
and Care Manual.
Release when °F flashes.
Hold 10 seconds
Comment
or
Repeat to switch back.
Display (and cabinet light) not
operable in Blackout Mode.
Hold light for 10 seconds to
exit.
* Drawer Wine Cooler: Initially, top bar will flash to set to zone. After five seconds of inactivity (or touching light button), the bottom
zone (bottom bar on F flashing) can be adjusted. After five seconds of inactivity, set-point will be stored in unit.
Glass Door Models
Task
Touch
Touch
Display
Light normally goes on/off
with door opening. Pressing
light button will turn
interior light on for 4 hours,
then it will turn off.
Cabinet Light
Display Off
Mode
Comment
Display off when door is
closed (unless cabinet light is
switched on). Repeat to
switch back.
Hold
All Ice Makers
Task
Ice Maker Off
Mode
Touch
Touch
Display
Hold
Comment
Repeat to switch back
Clear Ice & Clear Combo Only
Task
Touch
Touch
Display
Comment
Clean Cycle
Hold
Will automatically return to
ice production when clean
cycle is complete.
Ice Thickness
Adjustment
Hold
Use warmer/colder to scroll.
Temporary
Shutdown
(Office Mode)
Hold
Ice maker will automatically
turn back on in three hours.
NOTE: 38°F is an example; the display will vary with actual set-point.
IMPORTANT
Factory recommended set-point is 38°F for refrigerators and beverage centers, and 50°F for wine coolers.
18
CO2175DWR
U-Line Corporation Limited Warranty
U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of
one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the
evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from
defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year
warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a
product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the
United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with
the replacement of any defective part. During years two through five of the warranty period for the sealed system, ULine shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and
Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall
cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other
charges, including transportation charges for replacements under this warranty and labor costs not specifically covered
by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product.
The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you
can register on-line at www.U-LineService.com.
The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God,
such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation,
unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the
controls; door reversal; or cleaning the condenser.
If a product defect is discovered during the applicable warranty period, you must promptly notify either the dealer from
whom you purchased the product or U-Line at P.O. Box 245040, Milwaukee, Wisconsin 53224 or at 414-354-0300. In no
event shall such notification be received later than 30 days after the expiration of the applicable warranty period. U-Line
may require that defective parts be returned, at your expense, to U-Lines factory in Milwaukee, Wisconsin, for
inspection. Any action by you for breach of warranty must be commenced within one year after the expiration of the
applicable warranty period.
This limited warranty is in lieu of any other warranty, express or implied, including, but not limited to any
implied warranty of merchantability or fitness for a particular purpose; provided however, that to the
extent required by law, implied warranties are included but do not extend beyond the duration of the
express warranty first set forth above. U-Lines sole liability and your exclusive remedy under this warranty
is set forth in the initial paragraph above. U-Line shall have no liability whatsoever for any incidental,
consequential or special damages arising from the sale, use or installation of the product or from any other
cause whatsoever, whether based on warranty (express or implied) or otherwise based on contract, tort or
any other theory of liability.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
CO2175DWR
19
ULIN_016357_30095.fm Page 20 Wednesday, February 7, 2007 12:45 PM
For General Inquiries:
P.O. Box 245040
Milwaukee, Wisconsin
53224-9540 U.S.A.
Phone (800) 779-2547
FAX (414) 354-5696
www.U-Line.com
For Service and Parts
Assistance:
Phone (800) 779-2547
(414) 354-0300
FAX (414) 354-5696
Email:
OnLineService@U-Line.com
www.U-LineService.com
E-mail:
OnlineParts@u-line.com
For more than four decades, U-Line has distinguished itself as the
leader in built-in under-counter ice making, refrigeration and
wine storage appliances.
An INSTALLATION MANUAL for your unit, providing complete
installation information, is available for download at
www.U-Line.com. Information for custom panel inserts per model,
including panel size, and instructions are available by visiting
www.U-Line.com.
When you need replacement parts, always request genuine U-Line
replacements be used. Visit www.U-Line.com to locate a parts
distributor in your area.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter ice makers, Combo® ice maker/refrigerators, Wine Captain® wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2007 U-Line Corporation
Publication No. 30095
02/2007 Rev. B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising