MHSC BUF400 Operating instructions

MHSC BUF400 Operating instructions
Unvented Vent-free
Fireboxes
Models: BUF400, BUF500
WARNINGS
If the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
– Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
– Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Installation & Operating
611013
Instructions
BUF cover
For use with a listed gas-fired unvented
decorative room heater not to exceed
40,000 BTU/hr. Do Not Build a Wood Fire.
Carefully review the instructions supplied
with the decorative type unvented room
heater for the minimum fireplace size
requirement.
Do not install an appliance in this
firebox unless this firebox meets
the minimum dimensions required
for the installation.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
61D1013 1/11 Rev. 9
BUF Vent-Free Fireboxes
CONTENTS
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.
Thank you and congratulations on your purchase of an MHSC vent free firebox.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Important Safety Information......................................3
General Installation Information.................................5
Before You Start.......................................................5
What You Will Need for Installation..........................5
Firebox and Framing Dimensions...............................6
Hearth Dimensions.......................................................7
Firebox Location...........................................................7
Minimum Clearances...................................................8
Firebox Framing...........................................................9
Fireplace Installation..................................................10
Canopy Installation....................................................10
Gas Line Installation.................................................. 11
Combustion Air...........................................................12
Optional AK-4 Outside Air Kit.................................13
Model 403 Duct Connector....................................14
Optional Equipment...................................................15
Replacement Parts ....................................................16
Warranty......................................................................19
61D1013
IMPORTANT SAFETY INFORMATION
INSTALLER
WARNING
Please leave these instructions with the appliance.
BUF Vent-Free Fireboxes
OWNER
Please retain these instructions for future reference.
• Any change to this heater or its controls can be dangerous.
• Improper installation or use of the heater can cause serious injury or death from
fire, burns, explosion or carbon monoxide poisoning.
• Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter
burner flame patterns.
• Do not use a blower insert, heat exchanger insert or other accessory, not
approved for use with this heater where applicable.
1. Due to high temperatures, the firebox should be
located out of traffic and away from furniture and
draperies.
2. Children and adults should be alerted to the hazard
of high surface temperature and should stay away
to avoid burns or clothing ignition.
3. Young children should be carefully supervised when
they are in the same room with the firebox.
4. Do not place clothing or other flammable material
near the fireplace when the firebox is in use.
5. Any safety screen or guard removed for servicing,
must be replaced prior to operating a heater within
the firebox.
6. Installation and repair should be done by a qualified
service person.
7. To prevent malfunction and/or sooting, an unvented
gas heater/firebox should be cleaned at least annually by a professional service person. More frequent
cleaning may be required due to excessive lint from
carpeting, etc. It is imperative that control compartments, burners and circulating air passageways be
kept clean.
8. CARBON MONOXIDE POISONING: Early signs of
carbon monoxide poisoning are similar to the flu with
headaches, dizziness and/or nausea. If you have these
signs, obtain fresh air immediately. Have the heater
serviced as it may not be operating properly.
9. The installation must conform with local codes or, in
the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.l/NFPA54.
10. This unit complies with ANSI Z21.91 ventless firebox
enclosures for gas-fired unvented decorative room
heaters.
11. Do not install the unvented heater in a bathroom.
12. Do not install the unvented heater in a bedroom unless
the maximum input rating is equal to or less than
10,000 Btu/hr.
61D1013
13. Correct installation of the ceramic fiber logs, proper
location of the heater, and annual cleaning are necessary to avoid potential problems with sooting. Sooting,
resulting from improper installation or operation, can
settle on surfaces outside the fireplace. See log placement instructions for proper installation.
14. Avoid any drafts that alter burner flame patterns. Do not
allow fans to blow directly into fireplace. Do not place
a blower inside burn area of firebox. Ceiling fans may
create drafts that alter burner flame patterns. Sooting
and improper burning will occur.
15. CAUTION: Candles, incense, oil lamps, etc. produce
combustion byproducts including soot. Vent-free appliances will not filter or clean soot produced by these
types of products. In addition, the smoke and/or aromatics (scents) may be reburnt in the vent-free appliance which can produce odors. It is recommended to
minimize the use of candles, incense, etc. while the
vent-free appliance is in operation.
16. An unvented gas-fired heater uses air (oxygen) from
the room in which it is installed. Provisions for adequate
combustion and ventilation air must be provided. See
installation guidelines.
17. Keep room area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
18. Unvented gas heaters are a supplemental zone heater.
They are not intended to be a primary heating appliance.
19. Unvented gas heaters emit moisture into the living
area. In most homes of average construction, this
does not pose a problem. In houses of extremely
tight construction, additional mechanical ventilation is
recommended.
20. During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain
oils, films or bonding agents. These chemicals are not
harmful but may produce annoying smoke and smells
as they are burned off during the initial operation of the
appliance; possibly causing headaches, or eye or lung
irritation. This is a normal and temporary occurrence.
Continued on page 4
IMPORTANT SAFETY INFORMATION
BUF Vent-Free Fireboxes
Continued from page 3
WARNING
Do not attempt to burn solid wood fuels,
vented gas log sets, or any other combustible
in this unvented firebox. Also, do not install
a vent-free gas log set in this firebox if the
minimum clearance and height requirements
of the log set are too large for the firebox.
NOTICE
The initial break-in operation should last two to three
hours with the burner at the highest setting. Provide
maximum ventilation by opening windows or doors to
allow odors to dissipate. Any odors remaining after this
initial break-in period will be slight and will disappear
with continued use.
21. Input ratings are shown in BTU per hour and are for
elevations up to 2,000 feet. For elevations above 2,000
feet, input ratings should be reduced 4 percent for each
1,000 feet above sea level. Refer to the National Fuel
Gas Code.
22. The appliance and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
23. The appliance must be isolated from the gas supply
piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
24. Do not use this room heater if any part has been under
water. Immediately call a qualified service technician
to inspect the room heater and to replace any part of
the control system and any gas control which has been
under water.
25. Never burn solid fuels in a fireplace where a unvented
room heater is installed.
26. Always have a fireplace screen in place when the
appliance is in operation, and unless other provisions
for combustion air are provided, the screen shall have
an opening(s) for induction of combustion air.
27. Do not fill spaces around the firebox with insulation or
other materials. These spaces must be maintained to
prevent the firebox from coming in contact with combustible materials.
Illustrations shown in this manual reflect
“typical” installations with nominal
dimensions and are for design and framing
reference only. Actual installations may
vary due to individual design preferences.
However, always maintain minimum
clearances to combustible materials and
do not violate any specific installation
requirements.
WARNING
Never connect unit to private (non-utility)
gas wells. This gas is commonly known
as wellhead gas.
Nous recommandons que nos
appareils de chauffage au gaz
soient installés et entretenus par
des professionnels qui ont été
accrédités aux È.U. par le National
Fireplace Institute ® (NFI) comme
étant des spécialistes du NFI en
matièred’appareils de chauffage
au gaz.
61D1013
GENERAL INSTALLATION INFORMATION
The new BUF400 and BUF500 Series are vent-free
fireboxes. They feature a self contained heat-circulating
system. These units also feature a 2-in1, flexible-face
system, sold as an accessory, that converts the circulating
system into a radiant system in seconds.
This installation manual will enable you to obtain a safe,
efficient and dependable installation of your vent-free
fireplace system.
Do not alter or modify the firebox or its components under
any circumstances. Any modification or alteration of the
firebox system, including but not limited to the firebox and
accessories, may void the warranty, listings and approvals
of this system and could result in an unsafe and potentially
dangerous installation.
BEFORE YOU START
Carefully inspect the contents for shipping damage. If any
parts are missing or damaged, immediately inform the
dealer from whom you purchased the appliance. Do not
attempt to install any part of the appliance unless you have
all the parts in good condition.
Make sure you have received all
parts
Check your packing list to verify that all listed parts have
been received. You should have the following:
1. Vent-Free Gas Firebox
2. Canopy
3. Installation and Operating Instructions
4. Five (5) sheet metal screws for canopy
61D1013
BUF Vent-Free Fireboxes
What you will need for installation
TOOLS and BUILDING SUPPLIES
•
•
•
•
•
•
•
•
•
•
•
Phillips screwdriver
• Square
Framing materials
• Hammer
Saw and / or saber saw
• Tee joint
Level
• Pipe wrench
Measuring tape
• Pliers
Electric drill and bits
Fireplace surround materials (noncombustible)
Caulking material (noncombustible)
Wall finishing materials
Piping complying with local codes
Pipe sealant approved for use with propane/L.P.G.
(resistant to sulfur compounds)
Refer to the installation instructions provided with the log
sets for items required for log set installation.
In planning the installation for the appliance it is necessary
to determine where the unit is to be installed and whether
optional accessories are desired. Gas supply piping should
also be planned. The following steps represent the normal
sequence of installation. Each installation is unique, however, and might require a different sequence.
1. Position firebox prior to framing or into prepared framing.
2. Field wire main power supply to models with fan kit.
(Electrical connections should only be performed by an
experienced, licensed /certified tradesman).
3. Plumb gas line. (Gas connections should only be performed by an experienced, licensed/certified tradesman).
4. Install vent-free gas log heater per the instructions
provided with the vent-free gas log heater.
5. Complete finish wall material, surround and optional
hearth extension to your individual taste.
FIREBOX and FRAMING DIMENSIONS
BUF Vent-Free Fireboxes
Rough
Opening
Depth
E
C
206M”
21”
G
1/2” - 5/8”
D - Rough Opening Width
E
F
Rough
Opening
Height
2456M”
656O”
34”
3456M”
I
216QE”
J
66QE”
6"
2"
B
A
2"
106”
14(6QE”
26QE”
Figure 1 Firebox and Framing Dimensions
Ref.
BUF400
A
40"
611013
B
36"
BUF dims
C24ZC\zn"
D - Chase Installation
40Z\v"
D - Recessed Installation
40C\v"
E
46C\v"
F
66Z\,"
G
33Z\zn"
BUF500
46"
42"
30ZC\zn"
46Z\v"
46C\v"
51C\,"
72B\,"
36B\zn"
61D1013
hearth dimensions and firebox location
BUF Vent-Free Fireboxes
FIREBOX LOCATION
C
Carefully select the best location for installation of your
vent-free firebox. The following factors should be taken
into consideration:
• Clearance to side wall, ceiling, woodwork and windows.
D
E
•
•
A
B
•
•
•
FP2901
Ref.
BUF400
BUF500
hearth dims
A
35Z\x"
41Z\x"
B
17"
17"
C20C\,"26C\,"
D21Z\x"21Z\x"
Figure 2 Minimum Hearth Dimensions
•
•
•
See “Clearances/Height Requirements on page 8.
Minimum clearances to combustibles must be maintained.
Location must not be affected by drafts caused by
kitchen exhaust fans, ceiling fans, return air registers
for forced air furnaces / air conditioners, windows or
doors.
Installation must provide adequate ventilation and combustion air.
DO NOT INSTALL THIS FIREBOX IN A BEDROOM
OR BATHROOM.
Location should be out of high traffic or windy or drafty
areas.
DO NOT INSTALL WHERE CURTAINS, FURNITURE,
CLOTHING OR OTHER FLAMMABLE OBJECTS ARE
LESS THAN 42" FROM FRONT OF HEATER.
Never obstruct the front opening of the vent-free firebox
or restrict the flow of combustion and ventilation air.
Minimize modifications to existing construction. Refer
to Figure 3 below for location suggestions.
Do not install in the vicinity where gasoline or other
flammable liquids may be stored. The vent-free firebox
must be kept clear and free from these combustible
materials.
FP2440
Figure 3 Location of Firebox
FP2440
fireplace locations
61D1013
MINIMUM CLEARANCES
BUF Vent-Free Fireboxes
Ensure that minimum clearances shown in Figures 4
through 7 are maintained. Left and right clearances are
determined when facing the front of the firebox.
Follow these instructions carefully to ensure safe installation. Failure to follow these requirements may create a
fire hazard.
1. Sidewall clearances: The clearance from the inside
of the appliance to any combustible wall should not be
less than 9". Figure 4
2. Ceiling clearance: The ceiling must be at least 42”
from the top of the firebox opening. Figure 4
3. Back wall clearnace: The appliance may be placed
against a combustible back wall.
12”
10”
Combustible
Material Can
Contact Top
of Fireplace
21”
6”
19”
256O”
16”
12”
Noncombustible Material
Only if Needed to Cover
Radiant Top Face
FP2690
Figure 5 Mantel Clearances
Mi 42"
nim
um
Finish Wall
Mi 9"
nim
um
Combustible
Material Area
Mi 9"
nim
um
FP2687
Figure 4 Clearance and Height Requirements
FP2687
4. Mantel clearances:
The canopy supplied with the unit
minimum
clearances
must be installed.
If a combustible
mantel is installed,
it must meet the clearance requirements as shown in
Figures 5 & 6.
23”
8”
FP2690
1”
56O”
Mantel clearances
FP2692
256O”
3”
56O”
56O”
6”
5”
6”
756O” 45°
756O”
9”
Figure 6 Mantel Leg Clearance
FP2692
mantel leg clearance
61D1013
floor CLEARANCES and FRAMING
FP2688
Figure 7 Minimum Clearance Above
Combustible Flooring
5" Minimum
The firebox may be installed directly on a combustible floor
or raised on a platform of an appropriate height. When
the firebox is installed directly on carpeting, tile, or other
combustible material, other than wood flooring, the firebox
shall be installed on a metal or wood panel extending the
full width and depth of the enclosure.
WARNING
Combustible
Material
Firebox framing can be built before or after the appliance
is set in place. Construct firebox framing following Figure 1
for your specific installation requirements. Refer to Figure
1 on Page 6 for firebox dimensions. The framing headers
may rest on the top of the firebox standoffs.
Do not fill spaces around firebox with
insulation or other materials. This could
cause a fire.
WARNING
5. Floor clearance: This inner chamber firebox floor must
be installed at least 5" above any combustible flooring
material, such as carpeting or asphalt tile, which is
closer than 14" to the base of the firebox. Figure 7
Or
The inner chamber firebox floor may be installed nearer
to the floor if a minimum of 14" of noncombustible material such as slate or marble is installed between the base
of the firebox and the combustible flooring. Figure 8
BUF Vent-Free Fireboxes
The fireplace must be installed giving full
consideration to the clearance and height
requirements identified in this manual.
FP2688
min floor combustible
Can be Less
Than 5"
Noncombustible
Material
FP2689
14” Minimum
Figure 8 Minimum Clearance above Combustible Flooring with
Noncombustible Material Installed at Base of Fireplace
FP2689
min floor clear noncomb
61D1013
fireplace and CANOPY INSTALLATION
BUF Vent-Free Fireboxes
1. Bend out the nailing flanges located on each side of the
firebox.
2. Slide the firebox into prepared framing or position firebox
in its final position and frame later.
3. Level the firebox by checking the top edge of the firebox.
Shim if necessary.
4. Anchor firebox to the side framing members using 8d
nails or other suitable fasteners. Figure 9
5. The canopy must be installed for safe operation of the
heater.
Canopy INSTALLATION
A canopy is furnished with each firebox and MUST be
installed for safe operation.
1. Locate three (3) holes at the top of the front frame.
Figure 10
2. Align the canopy with the holes in the top of the
frame.
3. Secure canopy to front of frame with screws provided.
Figure 10
Front Frame
Nail Sides Through
Nailing Flanges
Canopy
FP2903
Screws
Figure 10 Canopy Installation
10
FP2903
WARNING
FP2902
nailing flanges
FP2902
The firebox canopy must not be modified
canopy install
or replaced with a canopy that may be
provided with the unvented decorative
room heater.
WARNING
Figure 9 Location of Nailing Flanges
Close fireplace screen panel before
operating a decorative type unvented room
heater.
61D1013
Consult all local codes. All gas piping must be installed to
comply with local codes, or in the absence of local codes,
with the latest edition of the National Fuel Gas Code ANSI
Z223.1/NFPA54.
Remove the baseplate for ease of gas line installation.
Remove screws along the front edge of the baseplate
and bottom center piece of the firebox and set aside. Lift
baseplate and pull toward you. Replace baseplate prior to
connecting gas line to heater. Consult heater installation
and operating instructions for correct installation of the
heater into the firebox.
WARNING
Plumbing connections should only be
performed by a qualified, licensed plumber.
Main gas supply must be off when plumbing
gas line to fireplace or performing service.
BUF Vent-Free Fireboxes
Connecting directly to an unregulated
propane / L.P.G. tank can cause an
explosion.
WARNING
WARNING
GAS LINE INSTALLATION
Do not connect directly to natural gas 1/2
PSI or 2 PSI systems. Always make sure
natural gas pressure is regulated 10.5 w.c.
(maximum before operating the unit).
After completing connection, test all gas joints from the
gas meter to the gas heater regulator for leaks. Using
soap and water solution or a gas sniffer. DO NOT USE
AN OPEN FLAME.
The 1/2" gas line may enter either from the left side or right
side of the firebox. Gas access holes are provided on both
sides of the firebox.
A listed manual shutoff valve must be installed upstream
of the appliance. A union tee and plugged 1/8" NPT pressure tapping point should be installed upstream of hte
appliance.
IMPORTANT: Install main gas valve (equipment shutoff
valve) in an accessible location. The main gas valve is
for turning on or shutting off the gas to the fireplace.
A sediment trap may be upstream of the heater to prevent
moisture and contaminants from passing through trap to
the heater controls and burners. Failure to do so could
prevent the heater from operating reliably. Consult applicable codes.
An external regulator must be used on all propane/L.P.G.
heaters, in addition to the regulator fitted to the heater, to
reduce the supply tank pressure to 13" w.c. (maximum).
Any copper tubing used to supply propane / L.P.G. from
the tank must be internally tinned.
Note: When connecting propane / L.P.G. vent-free
room heaters, you must use pipe sealant resistant to
propane / L.P.G.
Important: Hold heater regulator with a wrench to
prevent movement when connecting to inlet piping.
Check gas type: The gas supply must be the same as
stated on the heater’s rating plate. If the gas supply
is different, DO NOT INSTALL THE HEATER. Contact
your dealer for the correct model.
61D1013
11
COMBUSTION AIR
BUF Vent-Free Fireboxes
Combustion Air
1. Locate combustion air assembly at an exterior location
which is not likely to be accidentally blocked in any manner. Locate assembly a min. of 12" above the snow line
to prevent blockage by snow accumulation.
2. Never mount the combustion air inlet assembly in a
garage or storage area where combustible fumes such
as gasoline might be drawn into the fireplace.
3. Combustion air can be drawn from the crawl space under a house when an adequate supply of air is provided
by open ventilation.
4. CAUTION: Do not take combustion air from attic
space or garage space.
5. Locate air supply inlet at least 3' away from any appliance vent terminal.
6. Avoid extremely long runs and numerous turns in the
duct leading from the fireplace to the combustion air
assembly. These conditions increase the resistance to
the free flow of air through the duct. Refer to Figures
11 through 14 for methods of installing the outside air
for combustion assemblies.
8' Max.
Inlet Grille
in Soffit
(Overhang)
FP2460
Figure 12 Concrete Slab Installation
(Optional Outside Air Runs)
Duct
Extended
to Miss
Joist
Above
Snow
Level
FP2460
OA slab install
To Outside Wall
Figure 13 Installation Above Basement or
Crawl Space
FP2461
FP2461
above basement
Ground
Level
FP2459
Outside
Wall
Inside Wall
Figure 11 Basement Installation
NOTE: Fireplace
model in illustrations may not be
FP2459
representative of your appliance.
OA basement install
FP2462
Figure 14 45° Corner Installation
on Slab Floor
12
FP2462
OA corner install
61D1013
WARNING
COMBUSTION AIR
BUF Vent-Free Fireboxes
DO NOT remove the cover if the outside
air will not be connected.
Screws
Air Starting
Collar
Duct
The use of outside air for combustion is optional unless
required by building codes. It is only necessary to supply
outside combustion air to one side of the fireplace. Use the
model AK4 combustion air kit.
Model AK-4 Combustion Air Assembly
1. Remove the cover plate from the 4" outlet opening location on the left or right outside of the fireplace.
2. Place the insulation ring between the AK-4 starting collar
and fireplace wall.
3. Place the starting collar (4") into the hole on the side
of fireplace. Fasten it in place with the four sheet metal
screws provided. Figures 15 and 16
Note: The air starting collar extends through the
fireplace outer wrap. When the air starting collar
is securely attached, it will form a seal against the
fireplace wall.
Insulation
Ring
Left Side of
Fireplace
FP2700
Figure 16 Attach Outside Duct to Starting Collar
FP2700
4. Attach outside duct to starting collar with duct clamp or
OA
screws. Figure
16duct
5. Cut a 6-inch diameter opening for model AK-4 in the
outside wall covering where the outside vent is to be
located. Figure 17
6. Select and cut a piece of duct long enough to attach to
the fireplace and stick out at least 3" beyond the face of
the wall to which the AK-4 inlet air vent will be attached.
Cut duct with a standard pocket knife. Figure 16
6"
Diameter
Hole
Shorter End
of Air Starting
Collar
Left Side of
Fireplace
Sheet Meal
AK-4 Starting Screws
Collar
WARNING
Figure 15 Attach Outside Air Starting Collar and Insulation
Ring to Left Side of Fireplace
FP1900
OA start collar
Use FP-4 U 8/08
duct for maximum efficiency
and safety. Do not use a combustible duct.
Always use UL Listed Class 0 or 1 duct
material.
61D1013
Screws
Duct
Extending
3" Min.
FP1904
Nail
Hole
AK-4 Inlet
Air Vent
Figure 17 Combustion Air Assembly for Model
AK-4
Screws
FP1904
AK4 install
8/08
13
COMBUSTION AIR
BUF Vent-Free Fireboxes
7. If the duct is the insulated type, push the insulation back
from one end of the duct approximately 2". Figure 18
8. Slip the exposed end of the duct over the starting collar
on the fireplace.
9. Using the sheet metal screws provided, secure the duct
end to the collar attached to the fireplace.
10.Nail or screw the combustion air assembly to the surface
of the wall.
Note: If the wall covering is brick or stone, use
appropriate masonry fasteners. If necessary, splice
the duct. Use a model 403-duct connector to splice
duct sections.
Install model 403 duct connector
1. Push insulation back approximately 2" from the end of
each duct.
2. Slip each duct over duct connector until an equal length
of connector extends into each duct.
3. Place duct clamp over the end of each duct. Tighten
duct clamp down snuggly.
4. Push insulation back into place and over duct clamp.
14
Insulation
Approximately 2” Duct
Connector
FP1907
Duct
Duct Clamp
Figure 18 Install Duct Connector 403
FP1907
Duct connector
8/08
61D1013
OPTIONAL EQUIPMENT
BUF Vent-Free Fireboxes
Forced Air Kit (FA2A)
WARNING
If you are installing the forced air kit, Model FA2A, see the
installation instructions provided with the kit for electrical
wiring requirements, or the blower installation section. The
firebox must be connected to main power supply at time of
firebox installation. The blower must be installed prior to
the installation of the vent-free heater. The electrical connections must be made before the firebox is framed and
enclosed in the finished walls.
Electrical connections should only
be performed by a qualified, licensed
electrician, main power must be off when
connecting to main electrical power supply
or performing service.
The blower when installed, must be
electrically grounded in accordance with
local codes or in the absence of local codes,
with the National Electrical Code ANSI/NFPA
70.
61D1013
15
REPLACEMENT PARTS
BUF Vent-Free Fireboxes
1
3
3
2
Ref.
1.
2.
3.
4.
5.
6.
7.
16
DescriptionQty.
BUF400
BUF500
Canopy
126D456826D4706
611013
Screen Panel226D013126D0187
BUF parts
Screen Rod226D013226D0133
Rear Refractory
1
61D0102
61D0107
Side Refractory2
61D0101
61D0101
Bottom Refractory
1
61D0100
61D0106
Outside Air Kit
1
AK-4
AK-4
61D1013
BUF Vent-Free Fireboxes
61D1013
17
BUF Vent-Free Fireboxes
18
61D1013
BUF Vent-Free Fireboxes
LIMITED LIFETIME WARRANTY POLICY
The following components are warranted for life to the original owner, subject of proof of purchase:
Firebox, Combustion Chamber, Heat Exchanger, Grate, and Stainless Steel Burners.
Five Year Warranty
The following components are warranted for 5 years to the original owner, subject of proof of purchase: Vent Free Ceramic Fiber Logs, Catalytic Filter and Aluminized Burners.
Basic Warranty
MHSC warrants the components and materials in your gas appliance to be free from manufacturing
and material defects for a period of two years from date of installation. After installation, if any of
the components manufactured by MHSC in the appliance are found to be defective in materials or
workmanship, MHSC will, at its option, replace or repair the defective components at no charge to
the original owner. MHSC will also pay for reasonable labor costs incurred in replacing or repairing
such components for a period of two years from the date of installation. Any products presented
for warranty repair must be accompanied by a dated proof of purchase.
This Limited Lifetime Warranty will be void if the appliance is not installed by a qualified installer
in accordance with the installation instructions. The Limited Lifetime Warranty will also be void if
the appliance is not operated and maintained according to the operating instructions supplied with
the appliance, and does not extend to (1) firebox/burner assembly damage by accident, neglect,
misuse, abuse, alteration, negligence of others, including the installation thereof by unqualified
installers, (2) the costs of removal, reinstallation or transportation of defective parts on the appliance,
or (3) incidental or consequential damage. All service work must be performed by an authorized
service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty
of merchantability of fitness for purpose and of all other obligations or liabilities. MHSC does not
assume for it any other obligations or liability in connection with the sale or use of the appliance.
In states that do not allow limitations on how long an implied warranty lasts, or do not allow exclusion of indirect damage, those limitations of exclusions may not apply to you. You may also have
additional rights not covered in this Limited Lifetime Warranty.
MHSC reserves the right to investigate any and all claims against the Limited Lifetime Warranty
and decide upon method of settlement.
IF WARRANTY SERVICE IS NEEDED...
1. Contact your supplier. Make sure you have your warranty, your sales receipt and the model/
serial number of your MHSC product.
2. DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
61D1013
19
MHSC
149 Cleveland Drive • Paris, Kentucky 40361
www.mhsc.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement