Honda RedGum Silver Plus+ Lifter Owner's Manual

Owner’s Manual
Operating Instructions for
RedGum Silver Plus Lifter Splitter
REDGUM SPLITTERS
Australia’s No.1 Selling Honda Powered Log Splitters
Product Description & Intended Purpose:
This Log Splitter / Wood Splitter is an outdoor product that splits
wood logs for use as fuel in a fireplace or a woodstove.
WARNING: All operators must read this manual,
before operating this RedGum Splitter.
RGSPLS-0521 Rev 0
WARNING
Read and thoroughly understand all instructions contained in
this operation manual before operating this RedGum Splitter.
Serious injury or death can result if safety instructions are not
understood or followed. If you wish to discuss this log
splitter’s operational procedures after reading this manual,
please call our customer service personnel on 1300 039 251.
Monday - Friday 9am - 5pm AEDT
HAZARD SIGNAL DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in serious injury or death.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, will result in serious injury or death.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury.
2.
Table of Contents
Important Safety Rules ........................................ 4-6
Check Prior to Operation ......................................... 7
Preparing the Lifter Splitter for Use ......................... 8
Operation Instructions ........................................ 9-10
Preparing the Lifter Splitter to Tow ........................ 11
Log Splitter Components ....................................... 12
Engine Components & Specifications ................... 13
Maintenance, Storage & Essential Checks ........... 14
Log Splitter Troubleshooting ................................. 15
Warranty & Service Information ....................... 16-18
Notes ....... .............................................................. 19
Accessories ........................................................... 20
3.
Important Safety Rules
WARNING
1.) Read this manual completely.
- Serious injury or death can result if safety instructions are not followed.
- Everyone who operates this log splitter must read and completely
understand all safety rules, operating instructions, and maintenance
instructions.
- You must be 18 or older to operate this machine and in sound
mind, free of the influence of medication, drugs or alcohol. Keep
untrained people away.
2.) Crush hazard.
The Crush Hazard Zone is between the splitting wedge(4) and the
end plate(22). The Splitting wedge(4) can cut through skin and
break bones. Make sure hands are clear of crush hazard zone
when log splitter is in operation.
3.) Flying objects.
- Pieces of wood may fly out while splitting. Wear safety glasses.
Serious eye injury can occur if safety glasses are not worn.
- Serious accidents can happen when other people are allowed
inside the safety and operator zone. Keep everyone else out of the
safety and operator zone while operating log splitter. See page 7 for
operator zone.
4.) Skin injection hazard.
- High pressure fluid can inject under skin resulting in serious injury
including amputation.
- If skin injection happens, seek immediate “Surgical Treatment”.
Call 000
- Make sure all fittings are tight before starting the log splitter.
Relieve system pressure before servicing by turning off the log
splitter and moving control valve lever (3) forward and back and
returning to neutral position.
- Do not check for leaks with hand. Instead, use a cloth or place a
piece of card-board under the unit to check for leaks.
Safety Rules Continued...
4.
Important Safety Rules
WARNING
5.) Risk of fire and explosion.
Hot exhaust fumes from the engine can cause a fire. Gasoline is
highly flammable and explosive. You can be burned or seriously
injured when handling fuel.
- Position muffler at least 7 feet from combustible objects.
- Before adding fuel, stop the engine and keep heat, sparks, and
flame away. Do not add fuel when engine is running or still hot. No
smoking near engine.
- Do not pump fuel directly into engine at gas station. Static charge
can build and ignite fuel. Use an approved fuel container to transfer
petrol to the engine. Wipe up fuel spills immediately.
- Store and handle fuel outdoors. Gasoline vapors can ignite if they
collect inside an enclosure. Explosion can result.
- Do not change or add to exhaust system. Fire can result.
- Do not change or add fuel tanks or fuel lines. Fire can result.
- Before each use, check fuel tank and fuel lines for leaks. Any fuel
leak is a fire hazard. Fix any fuel leaks before starting engine.
- During transportation take precautions to make sure machine will
not tip over and cause a fuel leak and fire hazard. Engine fuel lever
should be turned to off while transporting this log splitter.
6.) Breathing hazard.
Poisonous fumes from the engine can kill you. Do not operate
indoors even if ventilated. This product is intended for outdoor
use only.
7.) Hot muffler.
You can be burned by the muffler. Do not touch muffler during
or immediately after use.
5.
WARNING
Read & thoroughly understand the following Operational Warnings
before operating this RedGum Log Splitter.
OPERATIONAL WARNINGS
· Intended purpose: This product is designed as an outdoor product to split wood
logs to use as fuel in a fireplace or a woodstove. Never use the log splitter for any
other purpose than splitting wood.
· Always place logs so the axehead/Splitting wedge (4) splits with the wood grain
and not across the wood grain.
· ALWAYS inspect log splitter before using to ensure it is in good working
condition.
· Replace or repair damaged or worn parts immediately.
· ALWAYS check and tighten fasteners, hardware and assembled parts before
operation.
· ALWAYS operate log splitter on firm, clear and level ground
· ALWAYS set up a SAFETY ZONE restricting onlookers to at least 3m away from
the log splitter when in use.
· ALWAYS remove split wood from around the log splitter immediately after it’s
spilt into smaller pieces so that you don’t stumble over it.
· Do NOT exceed equipment maximum splitting capacity by altering component
settings.
· Do NOT operate the log splitter at night, only during daylight hours.
· Shut engine off before leaving log splitter unattended.
RedGum Splitters are assembled and ready for use however:
• Check Hydraulic Oil levels with a Dipstick
• Check engine oil level by sighting engine dip stick.
• Closely inspect all log splitter components. If you sight damaged components then contact
your RedGum dealer before use.
• Always wear safety glasses while operating this log splitter. It’s also recommended to
wear Ear Muffs, Steel capped boots, Tight fitting gloves and Suitable clothing - A free from
hanging strings, jewelery or other items that could get caught up in moving parts. If you have
long hair make sure it is tied back and kept out of the way of moving parts.
Keep this operations manual handy for future reference and
re-read this Owner's Manual periodically
6.
CHECK PRIOR TO OPERATION
Essential checks to be carried out before each use:
What
When
How
Hoses
Each Use
Hydraulic Fittings
Each Use
Nuts & Bolts
Each Use
Inspect for exposed wire mesh & leaks. Replace
all worn/damaged hoses before starting engine.
Inspect for cracks & leaks. Replace all damaged
fittings before starting the engine.
Check for loose bolts. Tighten before operating.
Beam
Each Use
Apply grease to beam surface (if required).
Each Use
Clear debris
Serious accidents can happen when other people are allowed inside the
OPERATOR ZONE (see following diagram). Keep everyone out of the
operator zone while operating the log splitter.
ALWAYS set up a SAFETY ZONE restricting onlookers to at least 3
meters away from the log splitter when in use.
7.
13&1"3*/(5)&-*'5&341-*55&3'0364&
CAUTION-PXFSUIFMJGUJOHUBCMFCZGPMMPXJOHUIFQSPDFEVSFCFMPX
1. If lifting table is in Vertical position, SFNPWFQJO and MPXFS
MJGUJOHUBCMF until it is resting on the ground.
2. When the lifting table is on the ground, MPXFSSFBSTVQQPSU
MFH by SFNPWJOHQJO When the rear support leg is lowered
and touching the ground, SFQMBDFQJOUISPVHIUIFIPMFin the
rFBSTVQQPSUMFHIPMEFS and SFBS TVQQPSUMFH .
3. With both the lifting table and secured rear support leg
touching the ground, SPUBUFUIF+PDLFZ8IFFMIBOEMF until the log splitter is parallel with the ground.
4. -PDLUIF+PDLFZ8IFFM by pressing down on the tab.
8.
OPERATION INSTRUCTIONS
Proper Operation of the Log Splitter
1.) Always follow Operational warnings & checklist (refer pages 6-8).
2.) Start Engine by using the following instructions:
a. Turn the engine switch to ‘ON’ position.
b. Slide the choke lever away from the fuel tank to activate the choke.
c. Turn the fuel tap on.
d. Raise the engine revs by sliding the throttle lever away from the fuel tank. Always use
full throttle when using this machine.
e. Pull the starter cord handle lightly until resistance is felt, then pull briskly.
f. When the engine starts to run, deactivate the choke by sliding the lever towards the
fuel tank.
g. Do not let go of the starter cord suddenly. Prevent handle snapping by returning it to
engine.
3.) Place a log into the lifting table.
4.) Use the Lifting Table Control Valve (17) to raise the lifting table from the
ground. When the lifting table sits level with the Beam (6), roll the log onto the beam
and push the log's end against the End Plate (22).
WARNING The Log's end must sit correctly against the End Plate otherwise you
could damage the End Plate. Damaging the End Plate by incorrectly placing a log is
not covered under the warranty offered by the manufacturer. See next page for
instructions on splitting logs with a slant or uneven surfaces.
5.) Start the splitting procedure by pushing and holding the Control Valve
Lever (3) forward. Please note the Splitter Wedge (4) only moves forward when
you are holding the lever forward. When you let go of the Control Valve Lever (3),
the Splitter Wedge (4) stops immediately.
WARNING The Crush Hazard Zone is between the Splitter Wedge (4) and the End
Plate (22). Make sure hands are clear of the Crush Hazard Zone.
6.) To return wedge to starting position, simply pull the Control Valve Lever (3)
backwards and away from the End Plate (22). Please note the Splitter Wedge (4)
returns back to the original starting position automatically. You should observe the
Control Valve Lever (3) returns to the neutral position after the Splitter Wedge (4)
has returned back to it’s original starting position. Please also note for safety
reasons, the Splitter Wedge (4) stops approx. 3-4cm from the End Plate (22).
WARNING To avoid the build up of Hydraulic Pressure, please refrain from holding
the Control Valve Lever (3) forward after the Splitter Wedge (4) has reached the
end of it's travel.
7.) Clear the split wood from the operator zone.
8.) Repeat above steps as required.
9.
IMPORTANT OPERATION INSTRUCTION
Correct Placement of logs onto the Log Splitter is Required Prior to Splitting Logs in
order to Prevent Damage to the End Plate, Splitting Wedge & Splitting Beam
Correct operating procedures are required to ensure your RedGum log splitter is not
damaged. Incorrect operation can result in bending the Beam (6), Splitting Edge (4) and/or
End Plate (22). Important: If Beam, Wedge or End Plate are bent due to incorrect operation,
it is not the manufacturers fault and subsequently would not be covered under warranty.
Ideally the log should be cut into “rounds” with flat or even surfaces. If they are cut and the
edges are on an angle or have an uneven surface, you must ensure you place the log onto
the Beam (6) as shown in the Second or Third diagrams, as shown below:
10.
WARNING
Towing incorrectly is a serious risk and can result in injury or death.
Please read the following Towing Warnings:
Remember to turn the engine and fuel tap to the off position prior to towing. This is to
prevent flooding of the engine.
• IMPORTANT: Log Splitter is not approved or designed to be towed on Public Roads.
• Serious injury or death can occur if Towing Safety Rules are not followed.
• Review Towing Safety Warnings as mentioned in your Owner's Manual.
• Drive safely. Be aware of the added length that the lifter splitter adds to your vehicle.
• Never ride on or transport cargo on the lifter splitter.
• Always secure and lock the lifter splitter to the vehicle hitch before towing.
• Drive the vehicle only after the lifter splitter is securely attached.
• Turn off the vehicle if leaving the lifter splitter unattended.
• Choose a leveled surface to operate the lifter splitter.
• Block the lifter splitter's wheels to prevent any unattended movement.
• Never tow or operate this splitter while under the influence of alcohol, drugs or
medication.
• Avoid large holes and ditches when towing the lifter splitter in a vehicle.
• Always tow at a reduced speed on rough or uneven terrains, along the side of creeks,
ditches and hillsides.
• Do not exceed a speed of 45KM/H when towing the lifter splitter.
• Follow the "Preparing the Lifter Splitter to Tow" instructions in order as shown.
PREPARING THE LIFTER SPLITTER TO TOW
11.
LOG SPLITTER COMPONENTS
1.) 50mm Coupler - Attaches the log splitter to the 50mm hitch ball.
2.) Hydraulic Cylinder - 4½” bore and 23” stroke.
3.) Control Valve Lever - Controls the forward & backward movement of splitting wedge.
4.) 8” Wedge - Features wedge wings and tapered ends making splitting easier.
5.) Log Cradle - Keeps the log on the beam without operator assistance.
6.) Beam - 6” extra wide flange.
7.) Safety Chains - Safety feature to prevent loss of log splitter while towing.
8.) Lifting Table - Used for lifting the log.
9.) Engine - The air cooled Honda GP160 engine powers the log splitter.
10.) Fenders
11.) Tyres - Maximum rated towing speed is 45MPH (i.e. 72KPH).
12.) Gear Pump - Pumps the hydraulic oil through the system.
13.) Tow Bar
14.) Jockey Wheel - 8” diameter and 2” width.
15.) Rear Support Leg - The leg supports the log splitter steadily while operating.
16.) Hydraulic Table Lift Ram - Assists in lifting and lowering the hydraulic table.
17.) Lifting Table Control Valve - Handle for controlling the Lifting Table
18.) Rear support leg holder
19.) Jockey Wheel Handle
20.) Oil Tank Bolt/Breather
21.) Oil Tank
22.) End Plate
12.
ENGINE COMPONENTS
1.) Fuel Cap
2.) Fuel Tank
3.) Oil Drain Plug
4.) Oil Filler Cap/Dipstick
5.) P.T.O Shaft
6.) Muffler
7.) Spark Plug
8.) Choke Lever
9.) Fuel Valve Lever
10.) Starter Grip
11.) Recoil Starter
12.) Air Cleaner
1
12
6
2
11
7
5
4
3
8
9
10
For more information on Engine Operation & Engine Maintenance,
please refer to engine manual supplied with the log splitter.
SPECIFICATIONS
30000kgs
18 Seconds
20cm(8”)
14 Litres
600mm (24”)
45kgs (100Lbs)
50mm
40mm (16”)
45 Km per hour
41/2” x 223/4”
3500 psi
10W-AW32 &/or 10W-AW46
2 stage
46.8 LPM
Detent (auto-return)
Tested Splitting Force
Fastest Cycle Time
Solid Splitting Wedge Size
Hydraulic Tank Capacity
Max. Log Length
Max. Log Weight
Coupler Ball Size
Tyre Size
Max. Towing Speed
Cylinder Size
Max. Pressure
Hydraulic Fluid Type
Gear Pump
Max. Flow Capacity
Control Valve
Overall dimensions of the log splitter when horizontal:
Weight
244Kg
Height
1.2mm (45”)
1.05 m
Width
2.30 m
Length
13.
MAINTENANCE, STORAGE & ESSENTIAL
CHECKS
Before performing maintenance, the log splitter must be placed in maintenance mode. To
do so, follow the below steps:
1.) Turn off engine
2.) Move the Control Valve Lever (3) forward and backward to relieve Hydraulic Pressure
and leave in neutral position.
3. After performing maintenance, make sure all guards, shields and safety features are put
back in place. Failure to follow this warning can result in serious injury.
MAINTENANCE SCHEDULE
COMPONENT
Complete Unit
On Off Switch
Choke/Primer
Engine Oil
Throttle Lever
Cables and
Connections
Fuel Filter
Carburettor
Air Filter
Clutch
Spark Plug
Cooling Fins
Starter Cord
Starter
Housing Vents
Spark Arrestor
All Screws, Nuts &
Linkage
Interval
2
3
4
I
I
I/A
I
I
I
I
I
R
I
I/C
I
I/A
R
I
I
I
I
I
I
Yes
I/A
I
I/A
I
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
I
T
I
I
I
I
I
I
R
T
T
I C/R I/C
I
I
I/C R
I
I/C C
C
I
I
I
Yes
Yes
I
I/C
C
C
Yes
Yes
I
I
I/R
I
Yes
Yes
I
I
I
I
L/S
C/S
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1
COMPONENT
Anti Vibration
Mounts
Hydraulic Oil
Hydraulic Oil Pump
Hoses
Hydraulic Fittings
Beam
Control Valve
Belts
Blades
Flails/Hammers
Interval
2
3
L/S
C/S
Yes
Yes
I
I
I
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I/R
I
I
I/C
I
I
I/A
I/R
I/R
1
4
I
I/A
I
I/C
I
I
LEGEND: L/S = Log Splitter, C/S = Chipper Shredder
I = Inspect, T = Tune, R = Replace, C = Clean, S = Sharpen, A = Adjust, L
= Lubricate
INTERVAL:
1 = Pre Delivery, 2 = First Service, 3 = Dealer Service, 4 = Every time the
machine is used
DEALER SERVICE:
Oil Filter
Your machine is fitted with an Oil Filter. After the first 25 hours of operation, change the oil filter.
Thereafter, change oil filter after every 100 hours of use (or change it seasonally).
Storage
• Before storing, make sure the log splitter is clean and dry.
• Lightly lubricate all log splitter surfaces and moving parts to prevent rust.
• Store indoors or protected area and preferably under the RedGum Cover when the log splitter is
not being used.
• It is essential to fully retract the splitting wedge, ensuring no silver part of piston rod is exposed
to the elements.
WARNING
Skin Injection Hazard - Refer to your Engine Manual for further instructions
High pressure fluid can inject under the skin and can result in serious injuries!
− Make sure all hose and control fittings are tight before applying pressure. Relieve
system pressure before servicing, as explained in point 2 at the top of the page.
− Do not check for leaks with your hand. Instead, place a piece of cardboard under the unit
to check for leaks.
− If skin injection occurs, seek immediate 'Surgical Treatment'. Call 000.
14.
LOG SPLITTER TROUBLESHOOTING
Problem
Solution
Cylinder rod & splitting wedge will not
move
Solution: A, D, E, H, J
Slow cylinder shaft speed when
extending or retracting
Solution: A, B, C, H, I, K, L
Wood will not split or splits extremely
slowly
Solution: A, B, C, F, I, K
Engine bogs down during splitting
Solution: G, L
Engine stalls under low load condition
Solution: D, E, L, M
Cause
Solution
A - Insufficient oil to pump
Check oil level in reservoir
B - Air in oil
Check oil level in reservoir
C - Excessive pump inlet vacuum
Check pump inlet hose for blockage or
kinks
D - Blocked hydraulic lines
Flush & clean the splitter hydraulic
system
E - Blocked control valve
Flush & clean the splitter hydraulic
system
F - Low control valve setting
Adjust control valve with a pressue
gauge
G - High control valve setting
Adjust control valve with a pressue
gauge
H - Damaged control valve
Return control valve for authorised
repair
I - Internal control valve leak
Return control valve for authorised
repair
J - Internal cylinder leak
Return cylinder for authorised repair
K - Internally damaged cylinder
Return cylinder for authorised repair
L - Engine control out of adjustment
Return for authorised repair
M - Engine is loaded during idle down
mode
Use shorter log length (24” or less) to
allow engine to speed up before contact
15.
ENGINE COMPONENTS
WARRANTY AND SERVICE INFORMATION
Congratulations on the purchase of your new RedGum product. RedGum
Products will assist you to complete the “job at hand” in an economical, safe
and efficient manner.
This brochure explains the Warranty and Maintenance information for your
product. This combined with your Owner’s Manual and the knowledge and
expertise offered to you by your respective RedGum Dealer should provide you
with the confidence that your decision to purchase a RedGum product was a
good one.
STATEMENT OF WARRANTY
This statement of warranty applies to all RedGum products (offered by the
manufacturer, RedGum Products). The manufacturer provides this warranty to
the initial purchaser of this product (who has purchased it from an authorised
RedGum Products dealer) for a period commencing from the date of purchase.
If the product is found to be defective,
in RedGum Products'
SPECIFICATIONS
opinion (due to a fault of the manufacturer) within the Warranty
Period, RedGum Products will carry out the repair or
replacement to the customer Free of Charge, provided:
• The fault is reported directly to the place of purchase.
• Sufficient proof of purchase is provided.
• The fault is not caused by misuse, neglect or incorrect
adjustment by the user.
• The failure has not occurred through normal wear and tear.
• The product has not been serviced, repaired or alterations made
by any one not authorised by RedGum Products to do so.
The Warranty Periods
The warranty periods mentioned below commence on your date of purchase:
Customer Type
Private/Domestic
Commercial
RedGum
Splitter
24 months
3 months
RedGum
Chipper
12 Months
3 Months
NOTE:
- Engines are covered by the respective original
equipment manufacturers warranty and claims are made
direct to the manufacturer agent.
- Replacement parts and accessories fitted during a
repair under terms of warranty will enjoy cover for the
remainder of the warranty period of the finished product.
Please note that the Warranty Claims can only be made through
an Authorised RedGum Dealer
16.
ENGINE COMPONENTS
WHAT IS NOT COVERED BY WARRANTY
The following items are not covered by
this warranty:
• Normal maintenance items which become worn
through use, including, but not limited to, belts,
blades, oil, blade adapters, filters, rewind springs,
spark plugs, starter ropes, clutches and sprockets.
• Natural discoloration of material due to sunlight.
• Engines not manufactured by RedGum Products,
these items are covered by the respective original
equipment manufacturers’ warranty, all claims must
be sent to the appropriate manufacturer’s agents.
• Using stale or contaminated fuel in the product.
• Damage or failure caused by accident, misuse
and/or neglect, including, ingress of dirt, abrasives,
moisture, rust & corrosion, and damage due as a
result of inadequate maintenance.
• Failure to operate or maintain the unit in
accordance with the Owners/Operators manual, this
handbook or instruction given by a RedGum dealer.
• Alterations or modifications that change the
intended use of the product or affect the product's
performance, operation, safety or durability, or
causes the product to fail to comply with any
applicable laws.
• Damage due to incorrect usage such as incorrect
log placement (as shown in the product's respective
Owner's Manual)
• Additional damage to parts or components due to
continued use occurring after any of the above.
ITEMS FOR WHICH A CHARGE WILL BE
MADE
The following list is a guide to the types of items for
which a charge will be made (unless failure is
caused by a defect in the manufacturer's materials
or workmanship).
Service: Maintenance servicing and all parts and
fluid replaced in line with the maintenance schedule
shown in this handbook.
Mechanical Adjustments: Including engine tuning,
adjusting brakes, belts & clutches etc.
Drive System: Sprockets, belts, clutches, pulleys
and bearings all wear and will require replacement.
Cutting Equipment: Blades, cutting discs and
hammers wear during use and sharpening/
replacement is required as a matter of normal
maintenance.
Spark Plugs: Periodic replacement is required to
ensure maximum engine performance and best
fuel economy.
Induction/Combustion System: The removal of
deposits and cleaning may be required from time
to time and should be performed as necessary.
Tyres: Tyres are subject to wear and if they come
in contact with external objects, they can deflate.
A flat tyre is not a warrantable item.
External Surfaces, Paint, Trim and other
Appearance items: Are affected by normal wear
and tear and exposure to environmental
conditions. A charge will be made for paint and
trim items that require attention due to causes
outside the manufacturer’s control.
Hydraulics: Changing hydraulic fluids
The frequency of replacement, repair or
adjustment will depend mainly on where and how
you use your product, weather, atmospheric and
environmental conditions and frequency of use.
SPECIFICATIONS
CUSTOMER RESPONSIBILITIES
The customer must provide to an authorised
RedGum Dealer their proof of purchase
information such as a receipt.
The product must exhibit reasonable care in the
maintenance, operation, storage and general
upkeep practices as explained in the maintenance
section of the Owners/Operators Manual or this
handbook. This includes the whole product or any
general wear item or component on the product.
Any costs incurred to obtain warranty
consideration or services is the customer’s
responsibility, including shipping and handling,
travel expenses, lost time, lost production or
pickup and delivery.
YOUR RIGHTS AS A CUSTOMER
The New Product Warranty that is provided by
RedGum Products is in addition to the rights and
remedies conferred on consumers by the relevant
authorities and/or legislation. The warranty does
not affect those rights or remedies, except to the
extent that their application may lawfully be
excluded. Any consequential, direct or incidental
loss or damage is not covered by the warranty.
Any statutory or other rights or remedies available
in connection with a claim for such loss or damage
should be pursued separately.
17.
ENGINE COMPONENTS
WHERE TO GO FOR WARRANTY REPAIRS
Take your product to any authorised RedGum Dealer if it needs
warranty repairs. All authorised RedGum Dealers will honour the New
Product Warranty, and will repair, replace or adjust free of charge any
part of your product that is defective in factory materials or
workmanship. Please note that RedGum is unable to reimburse the cost
of repairs carried out during the warranty period by a repairer who is not
an Authorised Servicing Dealer.
Visit www.RedGumProducts.com.au • Call 1300 039 251
SPECIFICATIONS
WARRANTY INFORMATION
Please note down for future reference:
RedGum Splitter Model: RedGum Silver Plus Lifter Splitter
Date of Purchase:..............................................................................................
Serial Number:...................................................................................................
Engine Number:.................................................................................................
Purchased from:................................................................................................
To find your nearest Authorised RedGum Products dealer, visit:
www.RedGumProducts.com.au or Call Toll Free 1300 039 251
The manufacturer reserves the right to make improvements in design
and/or changes in specifications at any time without incurring any
obligation to install them on units previously sold.
18.
NOTES
19.
ACCESSORIES AVAILABLE
1.) RedGum Hydraulic Oil (Fluid 46 5L) - RRP $49.75
High quality hydraulic oil fluid - ideal for topping up the log
splitter's hydraulic reserve, when required.
2.) RedGum WorkTable & Heavy Duty WorkTable
Improves productivity by preventing split logs from falling to the
ground. It also helps reduce the effort of picking up split logs that
require further splitting.
WorkTable - $99, Heavy Duty WorkTable - $129 (pictured)
3.) RedGum Log Splitter Cover - RRP $89
Extra Heavy Duty 200D log splitter cover for protection against
dust and heavy rain.
4.) RedGum Log Turn Table - RRP $329
Our Patented Turn Table accessory fits all RedGum Log Splitters
and allows for easy turning of heavy logs (for repeat splitting)
when in vertical position.
5.) The Davis Starlifter - RRP $289
Dual-purpose tool designed to lift and elevate logs off the ground
to a more steady position for cutting. Also lifts T-posts vertically
out of the ground.
5.) Wood Pick (40cm, 60cm & 80cm)
Improves the overall speed and reduces back strain of most
forestry jobs. Simply pierce the log with the wood pick to easily
move the log from one place to another.
40cm - $89, 60cm - $100, 80cm - $115
6.) Chainsaws and Chainsaw accessories
For Chainsaws and their respective accessories, get in touch with
your authorized RedGum dealer.
For more information contact your local RedGum Dealer
Visit: www.RedGumProducts.com.au
Phone: 1300 039 251
20.