2MP ColorVu Smart Hybrid
Light Audio Fixed
Bullet & Turret Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer.
This manual applies to the models below:
Type Model
DS-2CE10DF0T-LFS
Type I Camera
DS-2CE10DF0T-LPFS
Type II Camera
Type III Camera
DS-2CE12DF0T-LFS
DS-2CE70DF0T-LPFS
Type IV Camera DS-2CE70DF0T-LMFS
Type V Camera DS-2CE72DF0T-LFS
This manual may contain several technical mistakes or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
01040020230322
Initiatives on the Use of Video Products
Thank you for choosing Hikvision products.
Technology affects every aspect of our life. As a high-tech company, we are increasingly aware of the role technology plays in improving business efficiency and quality of life, but at the same time, the potential harm of its improper usage. For example, video products are capable of recording real, complete and clear images. This provides a high value in retrospect and preserving realtime facts. However, it may also result in the infringement of a third party’s legitimate rights and interests if improper distribution, use and/or processing of video data takes place. With the philosophy of “Technology for the Good”, Hikvision requests that every end user of video technology and video products shall comply with all the applicable laws and regulations, as well as ethical customs, aiming to jointly create a better community.
Please read the following initiatives carefully:
1.
Everyone has a reasonable expectation of privacy, and the installation of video products should not be in conflict with this reasonable expectation.
Therefore, a warning notice shall be given in a reasonable and effective manner and clarify the monitoring range, when installing video products in public areas. For non-public areas, a third party’s rights and interests shall be evaluated when installing video products, including but not limited to, installing video products only after obtaining the consent of the stakeholders, and not installing highly-invisible video products.
2.
The purpose of video products is to record real activities within a specific time and space and under specific conditions. Therefore, every user shall first reasonably define his/her own rights in such specific scope, in order to avoid infringing on a third party’s portraits, privacy or other legitimate rights.
3.
During the use of video products, video image data derived from real scenes will continue to be generated, including a large amount of biological data (such as facial images), and the data could be further applied or reprocessed. Video products themselves could not distinguish good from bad regarding how to use the data based solely on the images captured by the video products. The result of data usage depends on the method and purpose of use of the data controllers. Therefore, data controllers shall not only comply with all the applicable laws and regulations and other normative requirements, but also respect international norms, social morality, good morals, common practices and other non-mandatory requirements, and respect individual privacy, portrait and other rights and interests.
4.
The rights, values and other demands of various stakeholders should always be considered when processing video data that is continuously generated by video products. In this regard, product security and data security are extremely crucial.
Therefore, every end user and data controller, shall undertake all reasonable and necessary measures to ensure data security and avoid data leakage, improper disclosure and improper use, including but not limited to, setting up access control, selecting a suitable network environment (the
Internet or Intranet) where video products are connected, establishing and constantly optimizing network security.
Video products have made great contributions to the improvement of social security around the world, and we
believe that these products will also play an active role in more aspects of social life. Any abuse of video products in violation of human rights or leading to criminal activities are contrary to the original intent of technological innovation and product development. Therefore, each user shall establish an evaluation and tracking mechanism of their product application to ensure that every product is used in a proper and reasonable manner and with good faith.
© 2022 Hangzhou Hikvision Digital Technology Co., Ltd.
All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the
Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website
( https://www.hikvision.com/ ).
Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.
Trademarks
and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE
PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS
FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT
BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL
HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA, CORRUPTION OF SYSTEMS, OR LOSS OF
DOCUMENTATION, WHETHER BASED ON BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT
LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE
USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET
PROVIDES FOR INHERENT SECURITY RISKS, AND
HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER
DAMAGES RESULTING FROM CYBER-ATTACK, HACKER
ATTACK, VIRUS INFECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE
TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH
ALL APPLICABLE LAWS, AND YOU ARE SOLELY
RESPONSIBLE FOR ENSURING THAT YOUR USE
CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU
ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A
MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF
THIRD PARTIES, INCLUDING WITHOUT LIMITATION,
RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS,
OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU
SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED
END-USES, INCLUDING THE DEVELOPMENT OR
PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE
DEVELOPMENT OR PRODUCTION OF CHEMICAL OR
BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT
RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE
NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN
RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS
MANUAL AND THE APPLICABLE LAW, THE LATTER
PREVAILS.
Regulatory Information
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards listed under the Directive 2014/30/EU (EMCD), Directive
2001/95/EC (GPSD) and Directive 2011/65/EU (RoHS).
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information, see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and
“Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings Follow these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material damage.
Warnings
In the use of the device, you must be in strict compliance with the electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 and IEC62368-1 standard. Refer to technical specifications for detailed information.
Do not connect multiple devices to one power adapter to avoid over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cord, and then contact the service center.
Never attempt to disassemble the camera by unprofessional personal.
Cautions
Do not drop the camera or subject it to physical shock.
Do not touch senor modules with fingers.
Do not place the camera in extremely hot, cold (the operating temperature shall be -40°C to 60°C), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser
beam.
Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Keep the camera away from liquid while in use for non-
water-proof device.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
The beam of the light at the distance of 200 mm is classified as Risk Group 1 (RG1). Possible hazardous optical radiation emitted from this product.
DO NOT stare at operating light source. May be harmful
to the eyes.
Wear appropriate eye protection or turn on the supplement light only at a safe distance (0.3 m) or in the area that is not directly exposed to the light when installing or maintaining the device.
Mark Description
Table 0-1 Mark Description
Mark Description
DC Voltage
1 Introduction
1.1
Product Features
The main features are as follows:
High performance CMOS sensor
OSD menu with configurable parameters
24-hour color image
Smart light
3-axis adjustment
1.2
Overview
1.2.1
Overview of Type I Camera
Switch Button
Power Cord
Video Cable
Microphone
Lens
Bracket
Main Body
Figure 1-1 Overview of Type I Camera
Note:
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS
1.2.2
Overview of Type II Camera
Microphone
Switch Button
Power Cord
Video Cable Bracket
Main Body
Lens
Figure 1-2 Overview of Type II Camera
Note:
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
1.2.3
Overview of Type III Camera
Gang Box
Base
Switch Button
Power Cord
Video Cable
Microphone
Enclosure
Main Body
Figure 1-3 Overview of Type III Camera
Note:
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
1.2.4
Overview of Type IV Camera
Enclosure
Microphone
Base
Set Screw
Main Body
Switch Button
IN DC12V
Power Cord
Video Cable
Figure 1-4 Overview of Type IV Camera
Note:
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
1.2.5
Overview of Type V Camera
Main
Body
Microphone
Switch Button
Power Cord
Video Cable
Enclosure
Base
Gang Box
Figure 1-5 Overview of Type V Camera
Note:
Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
2 Installation
Before you start
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the installation environment.
Check whether the power supply is matched with your
power output to avoid damage.
Make sure the wall is strong enough to withstand three
times the weight of the camera and the mount.
If the product does not function properly, contact your dealer or the nearest service center. DO NOT disassemble the camera for repair or maintenance by yourself.
2.1
Installation of Type I Camera
2.1.1
Ceiling/Wall Mounting
Before you start:
Ceiling mounting and wall mounting are similar. Following steps take ceiling mounting as an example.
Steps:
1.
Paste the drill template (supplied) to the place where you want to install the camera.
2.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Screw Hole
Cable
Hole
Screw Hole
Screw Hole templat e
Figure 2-1 Drill Template
3.
(Optional) Drill the cable hole, when the cables are routed through the ceiling.
4.
Align the screw holes in the bracket to the ceiling, and secure the camera with three PA4 × 25 screws
(supplied).
Figure 2-2 Secure Camera to Ceiling
5.
Connect the power cord and video cable.
6.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, turn the trim ring counterclockwise to loosen it and adjust the positions according to the figure below.
Pan Position
[0° to 360°]
Trim Ring
Rotation Position
[0° to 360°]
Figure 2-3 3-Axis Adjustment
Tilt Position
[0° to 90°]
7.
Turn the trim ring clockwise to lock the positions.
2.1.2
Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Ceiling mounting and wall mounting are similar.
Following steps take wall mounting as an example.
Steps:
1.
Paste the drill template for junction box to the place where you want to install the camera.
2.
(Optional) For cement wall, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-4 Drill Template for Junction Box
3.
(Optional) Drill the cable hole, when the cables are routed through the wall.
4.
Take apart the junction box.
5.
Align the screw holes of the camera with those on the junction box cover. Attach the camera to the junction box cover with three PM4 × 10 screws.
Figure 2-5 Attach Camera to Junction Box Cover
6.
Secure the junction box body on the wall with three
PA4 × 25 screws (supplied).
Figure 2-6 Secure Junction Box on Wall
7.
Route the cables through the bottom cable hole or side cable hole of the junction box and connect the cables.
8.
Fix the junction box cover on its body with three PM3
× 16 L6 screws that come with the junction box.
Figure 2-7 Fix Junction Box Cover on Its
Body
9.
Repeat steps 6 to 7 of 2.1.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
2.1.3
Wall Mounting with Wall Mount
Before you start:
You need to purchase a wall mount in advance.
Steps:
1.
Take apart the wall mount.
Main Body
Cover
Figure 2-8 Take Apart Wall Mount
2.
Paste the drill template (supplied) to the place where you want to install the camera.
3.
Drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-9 Drill Template for Wall Mount
4.
Attach the main body of the wall mount to the wall and secure it with three PA4 × 25 screws (supplied).
Figure 2-10 Secure Main Body to Wall
5.
(Optional) Drill the cable hole, when the cables are routed through the wall.
6.
Secure the camera to the cover of the wall mount with three PM4 × 13 screws and three M4 screws.
PM4 × 13 screw
M 4 screw
Figure 2-11 Secure Camera to Wall Mount Cover
7.
Route the cables through the cable hole of the wall mount and connect the cables.
8.
Insert one end of the wall mount cover diagonally into the wall mount body, and then snap the other end of the cover upward on the body.
Main Body
Step 2
Step 1 Cover
Figure 2-12 Secure Cover to Body
9.
Lock the cover to the body with one PA3 × 8 screw.
Figure 2-13 Lock Cover to Body
10.
Repeat steps 6 to 7 of 2.1.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
2.2
Installation of Type II Camera
2.2.1
Ceiling/Wall Mounting
Before you start:
Ceiling mounting and wall mounting are similar. Following steps take ceiling mounting as an example.
Steps:
1.
Paste the drill template (supplied) to the place where you want to install the camera.
2.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Screw Hole
Cable
Hole
Screw Hole
Screw Hole templat e
Figure 2-14 Drill Template
3.
(Optional) Drill the cable hole, when the cables are routed through the ceiling.
4.
Align the screw holes in the bracket to the ceiling, and secure the camera with three PA4 × 25 screws
(supplied).
Figure 2-15 Secure Camera to Ceiling
5.
Connect the power cord and video cable.
6.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below.
Pan Position
[0° to 360°]
Rotation Position
[0° to 360°]
Trim Ring
Tilt Position
[0° to 180°]
Thumbscrew
Screw
Figure 2-16 3-Axis Adjustment
1).
Loosen the trim ring to adjust the pan position [0° to 360°].
2).
Loosen the thumbscrew to adjust the tilt position
[0° to 180°].
3).
Loosen the screw to adjust the rotation position
[0° to 360°].
7.
Tighten the trim ring and screws to finish the installation.
2.2.2
Ceiling/Wall Mounting With Junction Box
For installation with junction box, refers to 2.1.2
Ceiling/Wall Mounting with Junction Box.
2.2.3
Wall Mounting With Wall Mount
For installation with wall mount, refers to 2.1.3 Wall
Mounting with Wall Mount.
2.3
Installation of Type III Camera
2.3.1
Ceiling/Wall Mounting
Steps:
1.
Paste the drill template (supplied) to the place where you want to install the camera.
2.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-17 Drill Template
3.
Attach the gang box to the ceiling and secure it with three PA4 × 25 screws (supplied).
Figure 2-18 Attach Gang Box to Ceiling
4.
Fit the camera onto the gang box.
Figure 2-19 Fit Camera onto Gang Box
5.
Turn the camera clockwise until it snaps into the gang box.
Figure 2-20 Snap Camera into Gang Box
6.
Connect the power cord and video cable.
7.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below.
Rotation Postion
[0° to 360°]
Figure 2-21 3-Axis Adjustment
1).
Rotate the enclosure to adjust the pan position [0° to 360°].
2).
Move the main body up and down to adjust the tilt position [0° to 75°].
3).
Rotate the main body to adjust the rotation position [0° to 360°].
2.3.2
Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Steps:
1.
Loosen screws to take apart the junction box.
2.
Paste the drill template for junction box to the place where you want to install the camera.
3.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-22 Drill Template for Junction Box
4.
(Optional) Drill the cable hole, when the cables are routed through the ceiling.
5.
Secure the junction box body on the ceiling with three
PA4 × 25 screws that come with the junction box.
Figure 2-23 Secure Junction Box Body
6.
Route the cables through the bottom cable hole or the side cable hole of the junction box.
7.
Combine the junction box cover with its body and secure it with three PM3 × 13 screws.
Figure 2-24 Combine Junction Box Cover and Body
8.
Fix the gang box onto the junction box cover with PA4
× 10 screws that come with the junction box.
9.
Connect the power cord and video cable and put the cables back into the junction box.
10.
Press the camera base to the gang box. Turn the camera clockwise until it snaps into the gang box.
11.
Refer to step 6 to 7 of 2.3.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
Figure 2-25 Finish Installation
2.3.3
Wall Mounting with Wall Mount
Before you start:
You need to purchase a wall mount in advance.
Type I Wall Mount
Steps:
1.
Drill Ø10 mm screw holes in the wall where you want to install the wall mount.
2.
Use M6 × 75 metal expansion bolts to fix the wall mount onto the wall.
Figure 2-26 Fix Wall Mount
3.
Use PM4 × 10 screws to fix the gang box onto the wall mount.
Figure 2-27 Fix Gang Box
4.
Repeat the step 4 to 7 of 2.3.1 Ceiling/Wall Mounting
to adjust the angle and finish the installation.
Figure 2-28 Finish Installation
Type II Wall Mount
Steps:
1.
Take apart the wall mount.
Main Body
Cover
Figure 2-29 Take Apart Wall Mount
2.
Paste the drill template (supplied) to the place where you want to install the camera.
3.
Drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-30 Drill Template for Wall Mount
4.
Attach the main body of the wall mount to the wall and secure it with three PA4 × 25 screws (supplied).
Figure 2-31 Secure Main Body to Wall
5.
(Optional) Drill the cable hole, when the cables are routed through the wall.
6.
Secure the camera to the cover of the wall mount with three PM4 × 13 screws and three M4 screws.
PM 4 × 13 screw
M 4 screw
Figure 2-32 Secure Camera to Wall Mount Cover
7.
Route the cables through the cable hole of the wall mount and connect the cables.
8.
Insert one end of the wall mount cover diagonally into the wall mount body, and then snap the other end of the cover upward on the body.
Main Body
Step 2
Step 1
Cover
Figure 2-33 Secure Cover to Body
9.
Lock the cover to the body with one PA3 × 8 screw.
Figure 2-34 Lock Cover to Body
10.
Repeat steps 6 to 7 of 2.3.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
2.4
Installation of Type IV Camera
2.4.1
Ceiling/Wall Mounting
Steps:
1.
Loosen the set screw.
2.
Rotate the camera to align the triangle mark with the screw hole, and dissemble the camera.
Triangle
Mark
Figure 2-35 Dissemble Camera
3.
Paste the drill template (supplied) to the place where you want to install the camera.
4.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-36 Drill Template
5.
Use three PA4 × 25 screws (supplied) to secure the base to the ceiling.
Figure 2-37 Secure Base to Ceiling
6.
Align the screw hole with the triangle mark to install the camera back to the base and secure it.
Triangle
Mark
Figure 2-38 Install Camera Back
7.
Connect the power cord and video cable.
8.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below.
Pan Position
[0°to 360°]
Tilt Position
[0° to 75°]
Rotation Position
[0° to 360°]
Figure 2-39 3-Axis Adjustment
1).
Rotate the enclosure to adjust the pan position [0° to 360°].
2).
Move the main body up and down to adjust the tilt position [0° to 75°].
3).
Rotate the main body to adjust the rotation position [0° to 360°].
9.
Tighten the set screw to finish the installation.
Note:
If you need to adjust the angle after installation, loosen the set screw first and then repeat step 8 to 9.
Set Screw
Figure 2-40 Loosen the Set Screw
2.4.2
Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Steps:
1.
Loosen screws to take apart the junction box.
2.
Paste the drill template for junction box to the place where you want to install the camera.
3.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-41 Drill Template for Junction Box
4.
(Optional) Drill the cable hole, when the cables are routed through the ceiling.
5.
Secure the junction box body on the ceiling with three
PA4 × 25 screws that come with the junction box.
Figure 2-42 Secure Junction Box Body
6.
Route the cables through the bottom cable hole or the side cable hole of the junction box.
7.
Combine the junction box cover with its body and secure it with three PM3 × 13 screws.
Figure 2-43 Combine Junction Box Cover and Body
8.
Fix the base onto the junction box cover with three
M4 × 10 screws.
Figure 2-44 Fix Base
9.
Connect the power cord and video cable and put the cables back into the junction box.
10.
Repeat the step 6, 8, and 9 of 2.4.1 Ceiling/Wall
Mounting to adjust the angle and finish the
installation.
Figure 2-45 Finish Installation
2.4.3
Wall Mounting with Wall Mount
Before you start:
You need to purchase a wall mount in advance.
Steps:
1.
Drill Ø10 mm screw holes in the wall where you want to install the wall mount.
2.
Use four M6 expansion bolts to fix the wall mount onto the wall.
Figure 2-46 Fix Wall Mount
3.
Loosen the set screw.
4.
Rotate the camera to align the triangle mark with the screw hole, and disassemble the camera.
Triangle
Mark
Figure 2-47 Dissemble Camera
5.
Use M4 × 10 screws to fix the base onto the wall mount.
Figure 2-48 Fix the Base onto the Wall Mount
6.
Repeat steps 6 to 9 of 2.4.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
Figure 2-49 Finish Installation
2.5
Installation of Type V Camera
2.5.1
Ceiling/Wall Mounting
Steps:
1.
Paste the drill template (supplied) to the place where you want to install the camera.
2.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-50 Drill Template
3.
Attach the gang box to the ceiling and secure it with three PA4 × 25 screws (supplied).
Figure 2-51 Attach Gang Box to Ceiling
4.
Fit the camera onto the gang box.
Figure 2-52 Fit Camera
5.
Turn the camera clockwise until it snaps into the gang box.
Figure 2-53 Snap Camera into Gang Box
6.
Connect the power cord and video cable.
7.
Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below.
Pan Position
[0° to 360°]
Rotation Position
[0° to 360°]
Tilt Position
[0° to 75°]
Figure 2-54 3-Axis Adjustment
1).
Rotate the enclosure to adjust the pan position [0° to 360°].
2).
Move the main body up and down to adjust the tilt position [0° to 75°].
3).
Rotate the main body to adjust the rotation position [0° to 360°].
2.5.2
Ceiling Mounting with Junction Box/Inclined
Ceiling Mount
Before you start:
You need to purchase a junction box or inclined ceiling
mount in advance.
Ceiling mounting with junction box and inclined ceiling mount are similar. Following steps take junction box as an example.
Steps:
1.
Paste the drill template for junction box to the place where you want to install the camera.
2.
(Optional) For cement ceiling, drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-55 Drill Template
3.
(Optional) Drill the cable hole, when the cables are routed through the wall.
4.
Take apart the junction box.
5.
Install the gang box to the junction box cover with three PM4 screws.
Figure 2-56 Install Gang Box to Junction Box Cover
6.
Fit the camera onto the gang box.
Figure 2-57 Fit Camera
7.
Turn the camera clockwise until it snaps into the gang box.
Figure 2-58 Snap Camera into Gang Box
8.
Secure the junction box body on the ceiling with four
PA4 × 25 screws.
Figure 2-59 Secure Junction Box Body
9.
Route the cables through the bottom cable hole or the side cable hole of the junction box and connect the cables.
10.
Combine the junction box cover with its body.
Figure 2-60 Combine Junction Box Cover with Body
11.
Refer to step 6 to 7 of 2.5.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
2.5.3
Wall Mounting with Wall Mount
Before you start:
You need to purchase a wall mount in advance.
Type I Wall Mount
Steps:
1.
Drill Ø10 mm screw holes in the wall where you want to install the wall mount.
2.
Use four M6 expansion bolts to fix the wall mount onto the wall.
Figure 2-61 Fix Wall Mount
3.
Use three PM4 × 10 screws to fix the gang box onto the wall mount.
Figure 2-62 Fix Gang Box
4.
Repeat the step 4 to 7 of 2.5.1 Ceiling/Wall Mounting
to adjust the angle and finish the installation.
Figure 2-63 Finish Installation
Type I Wall Mount
1.
Take apart the wall mount.
Main Body
Cover
Figure 2-64 Take Apart Wall Mount
2.
Paste the drill template (supplied) to the place where you want to install the camera.
3.
Drill the screw holes with a 5.5 mm drill and insert the supplied wall plugs.
Figure 2-65 Drill Template for Wall Mount
4.
Attach the main body of the wall mount to the wall and secure it with three PA4 × 25 screws (supplied).
Figure 2-66 Secure Main Body to Wall
5.
(Optional) Drill the cable hole, when the cables are routed through the wall.
6.
Secure the camera to the cover of the wall mount with three PM4 × 13 screws and three M4 screws.
PM 4 × 13 screw
M 4 screw
Figure 2-67 Secure Camera to Wall Mount Cover
7.
Route the cables through the cable hole of the wall mount and connect the cables.
8.
Insert one end of the wall mount cover diagonally into the wall mount body, and then snap the other end of the cover upward on the body.
Main Body
Step 2
Step 1
Cover
Figure 2-68 Secure Cover to Body
9.
Lock the cover to the body with one PA3 × 8 screw.
Figure 2-69 Lock cover to Body
10.
Repeat steps 6 to 7 of 2.5.1 Ceiling/Wall Mounting to
adjust the angle and finish the installation.
3 Menu Description
Please follow the steps below to call the menu.
Note:
The actual display may vary with your camera model.
Steps:
1.
Connect the camera with the TVI DVR and the monitor, as shown in figure 3-1.
TVI DVR
Camera
Monitor
Figure 3-1 Connection
2.
Power on the camera, TVI DVR, and monitor to view the image on the monitor.
3.
Click PTZ Control to enter the PTZ Control interface.
4.
Call the camera menu by clicking button or calling preset No. 95.
VIDEO
FORMAT
MAIN MENU
EXPOSURE
LIGHTING
SETTINGS
VIDEO
SETTINGS
AUDIO
SETTINGS
FACTORY
DEFAULT
SHARPNESS
SATURATION
DNR
BACK
EXIT
SAVE & EXIT
AUDIO
VOLUME
BACK
EXIT
SAVE & EXIT
CANCEL
CONFIRM
EXPOSURE MODE
AGC
ANTI- BANDING
BACK
EXIT
SAVE & EXIT
LIGHTING MODE
IR/WHITE LIGHT
SMART IR
THRESHOLD
LEVEL
BACK
EXIT
SAVE & EXIT
IMAGE MODE
WHITE BALANCE
BRIGHTNESS
CONTRAST
EXIT
SAVE & EXIT
Figure 3-2 Main Menu Overview
5.
Click the direction buttons to control the camera.
1).
Click up/down direction buttons to select menu options.
2).
Click Iris + to confirm the selection.
3).
Click left/right direction buttons to adjust the value of the selected option.
3.1
VIDEO FORMAT
You can set the video format to 2MP@25 fps, 2MP@30 fps, PAL, or NTSC.
3.2
EXPOSURE
EXPOSURE MODE
You can set the EXPOSURE MODE to GLOBAL, BLC, HLC, or DWDR.
GLOBAL
GLOBAL refers to the normal exposure mode which adjusts lighting distribution, variations, and non-standard processing.
BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light to the object in the front to make it clear, but this may cause over-exposure of the background where the light is strong.
HLC (Highlight Compensation)
HLC stands for highlight compensation. The camera detects strong spots (over-exposure portion of image) and reduces the brightness of strong spots to improve the overall images.
DWDR (Digital Wide Dynamic Range)
Digital wide dynamic range gives the camera the ability to view dark areas of given image as well as extremely lighted portions of the image or areas of high contrast.
AGC (Auto Gain Control)
It optimizes the clarity of the image in poor light conditions. The AGC level can be set to HIGH, MEDIUM, or LOW.
Note:
The noise will be amplified when setting the AGC level.
ANTI-BANDING
ANTI-BANDING is a camera setting that prevents the appearance of horizontal lines (banding) when photographing images in low frequency light and high brightness environments.
3.3
LIGHTING SETTINGS
I LIGHTING MODE
IR and WHITE LIGHT are available.
IR
IR LIGHT
You can turn on/off the IR LIGHT to meet the requirements of different circumstances.
SMART IR
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure.
D N Threshold (Day to Night Threshold)
Day to Night Threshold is used to control the sensitivity of switching the day mode to the night mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
N D Threshold (Night to Day Threshold)
Night to Day Threshold is used to control the sensitivity of switching the night mode to the day mode. You can set the value from 1 to 9. The larger the value is, the more sensitive the camera is.
WHITE LIGHT
Under the WHITE LIGHT sub-menu, you can set the mode to OFF or AUTO.
OFF: Set it to OFF to give up this function.
AUTO: You can set THRESHOLD and LEVEL in this section.
THRESHOLD
The higher the threshold is, the more sensitive the device is to dark environment.
LEVEL
You can adjust the maximum brightness of supplement light.
3.4
VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. IMAGE MODE, WHITE BALANCE,
BRIGHTNESS, CONTRAST, SHARPNESS, SATURATION, and
DNR are adjustable.
VIDEO SET TINGS
IMAGE MODE STD
WHITE BALANCE
BRIGHTNESS
CONTRAST
SHARPNESS
SATURATION
5
5
5
5
BACK
EXIT
SAVE & EXIT
Figure 3-3 VIDEO SETTINGS
IMAGE MODE
IMAGE MODE is used to adjust the image saturation, and you can set it to STD (Standard), HIGH-SAT (High
Saturation), or HIGHLIGHT (better indoor facial details).
WHITE BALANCE
White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set WHITE BALANCE mode to AUTO or
MANUAL.
AUTO
Under AUTO mode, white balance is being adjusted automatically according to the color temperature of the scene illumination.
MANUAL
You can adjust the R-GAIN and B-GAIN value to correct colors manually.
WHITE BALANCE
MODE
R-GAIN
MANUAL
5
BACK
5
EXIT
SAVE&EXIT
Figure 3-4 WHITE BALANCE
BRIGHTNESS
Brightness refers to the brightness of the image. You can set the brightness value from 1 to 9 to darken or brighten the image. The greater the value is, the brighter the image is.
CONTRAST
This feature enhances the difference in color and light between parts of an image.
SHARPNESS
Sharpness determines the amount of detail an imaging system can reproduce.
SATURATION
Saturation is the proportion of pure chromatic color in the total color sensation. Adjust this feature to change the saturation of the color.
DNR
DNR refers to digital noise reduction.
This function reduces noise in video stream.
3.5
AUDIO SETTINGS
Under the AUTO SETTINGS sub-menu, you can set the mode to ON or OFF. Adjust the VOLUME value to turn up/down the volume.
AUDIO SETTINGS
AUDIO ON
BACK
5
EXIT
SAVE&EXIT
Figure 3-5 AUTO SETTINGS
3.6
FACTORY DEFAULT
Click CANCEL to back to the main menu.
Click CONFIRM to reset all the settings to factory defaults.
3.7
EXIT
Move the cursor to EXIT and click Iris+ to exit the menu.
3.8
SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save the settings and exit the menu.
UD31334B-A
