User Manual - Mettler Toledo

User Manual - Mettler Toledo

ICS685

ICS685 / ICS689

Weighing systems

ICS689

Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper use of your new equipment according to this Manual and regular calibration and maintenance by our factory-trained service team ensures dependable and accurate operation, protecting your investment. Contact us about a service agreement tailored to your needs and budget. Further information is available at www.mt.com/service

There are several important ways to ensure you maximize the performance of your investment:

1 Register your product: We invite you to register your product at www.mt.com/productregistration so we can contact you about enhancements, updates and important notifications concerning your product.

2 Contact METTLER TOLEDO for service: The value of a measurement is proportional to its accuracy – an out of specification scale can diminish quality, reduce profits and increase liability. Timely service from

METTLER TOLEDO will ensure accuracy and optimize uptime and equipment life.

ð Installation, Configuration, Integration and Training: Our service representatives are factorytrained, weighing equipment experts. We make certain that your weighing equipment is ready for production in a cost effective and timely fashion and that personnel are trained for success.

ð Initial Calibration Documentation: The installation environment and application requirements are unique for every industrial scale so performance must be tested and certified. Our calibration services and certificates document accuracy to ensure production quality and provide a quality system record of performance.

ð Periodic Calibration Maintenance: A Calibration Service Agreement provides on-going confidence in your weighing process and documentation of compliance with requirements. We offer a variety of service plans that are scheduled to meet your needs and designed to fit your budget.

3

Table of Contents

1 Introduction

1.1

1.2

1.3

1.4

Safety instructions

Presentation

Application overview

Commissioning

2 Operation

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

2.10

2.11

2.12

2.13

2.14

2.15

2.16

3 Counting

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

3.10

Switching on/off

Login/Logout

Straight weighing

Switching units

Zeroing / Zero point correction

Weighing with tare

Displaying information

Printing results

Average (dynamic) weighing

Working with identifications

Working in a higher resolution

Switching scales

Working with a prompt

Memory log files

Cleaning

Verification test

Counting parts into a container

Counting parts out of a container

Determining the parts in a full container

Counting with a known average piece weight

Changing reference quantity

Counting with reference weight check

Reference optimization

Counting with automatic reference determination

Counting with custom unit

Counting with reference and bulk scale

4 Over/Under Checkweighing and Filling

4.1

4.2

4.3

4.4

4.5

4.6

4.7

4.8

4.9

Overview

Specifying target values for Over/Under Checkweighing or Filling

Specifying target number of pieces for Over/Under Checkcounting

Over/Under Checkweighing or Checkcounting procedure

Filling procedure

Over/Under Checkweighing / Filling during subtractive weighing (Take away)

Over/Under Checkweighing / Filling with "Quick start"

Over/Under Checkweighing to zero / Filling to zero

Leaving Over/Under Checkweighing / Filling

5 Classifying

5.1

5.2

5.3

5.4

5.5

5.6

Overview

Specifying class definition values

Classifying procedure

Classifying during subtractive weighing

Automatic printout of Classifying results

Terminating Classifying

 29

 29

 29

 29

 30

 30

 30

 33

 33

 34

 35

 35

 36

 36

 43

 45

 46

 47

 47

 47

 48

 48

 48

 49

 50

 50

 51

 52

 7

 7

 8

 21

 25

 58

 58

 58

 59

 59

 60

 60

 53

 53

 54

 54

 55

 55

 56

 56

 57

 57

Table of Contents 5

6 Totalization

6.1

6.2

6.3

6.4

6.5

6.6

6.7

Starting totalization

Totalizing manually

Automatic totalizing

Totalizing to a target

Totalizing with leaving the totalized items on the scale

Statistical evaluation of the sum

Terminating totalizing

7 Settings in the menu

7.1

7.2

7.3

7.4

7.5

7.6

7.7

Menu overview

Operating the menu

Scale menu block

Application menu block

Terminal menu block

Communication menu block

Maintenance menu block

8 Quick Select menu

8.1

8.2

8.3

8.4

8.5

8.6

8.7

8.8

8.9

8.10

Quick Select menu overview

Entering main menu

Logout

Database

Calling up memory log file

Statistics

Performing routine test

Performing corner load test

Calling up routine test / corner load test log files

Calling up calibration log file

9 Event and error messages

9.1

Error conditions

9.2

9.3

9.4

Errors and warnings

Smart weighing counter / spanner icon

Service information

10 Technical data and accessories

10.1

Devices for dry environment

10.2

10.3

Devices for wet environment

General technical data

11 Appendix

11.1

11.2

11.3

11.4

Index

Metrological information

Table of Geo Code values

Disposal

Protocol printouts

 115

 115

 115

 115

 116

 121

 121

 121

 122

 123

 124

 125

 125

 126

 128

 128

 129

 129

 136

 144

 145

 145

 145

 146

 147

 148

 67

 67

 67

 70

 80

 96

 102

 113

 61

 61

 61

 63

 64

 64

 65

 66

6 Table of Contents

1 Introduction

1.1 Safety instructions

General

• Do not use the device in a hazardous environment. Special devices are available in our range of products for hazardous environments.

• The safety of the device cannot be ensured if it is not operated in accordance with these operating instructions.

• Only authorized personnel may open the device.

Devices with protection level IP5x or IP65

Devices with protection level IP54 or IP65 are protected against dust and splashing of water respectively dust-tight and protected from water jets according to EN 60529. They are suitable for use in dusty environments and brief contact with liquids.

• Ensure that the device is dried off after coming into contact with liquid.

• Do not use the device in environments with a risk of corrosion.

• Do not flood the device or submerge it in liquid.

Devices with built-in power supply unit

• Ensure that the power socket outlet for the device is earthed and easily accessible, so that it can be deenergized rapidly in emergencies.

• Ensure that the supply voltage at the installation site lies within the range of 100 V to 240 V.

• Ensure that there is a space of at least 3 cm (1.25") at the rear in order to prevent the power cable from being bent too strongly.

• Check the power cable regularly for damage. If it is damaged, immediately disconnect the device from the power supply unit.

Devices with built-in storage battery

• Only use storage batteries from the manufacturer.

• Do not use the battery charger in humid or dusty rooms or below 0 °C (32 °F) ambient temperature.

• After the storage battery has been charged, the cover cap of the charging socket on the device must be closed.

Compact scales / Terminal and platform combinations

• Avoid falling and shock loads as well as any impact from the side.

• The maximum static safe load must never be exceeded. Observe the operation limits, see technical data of the connected weighing platform.

Introduction 7

1.2 Presentation

1.2.1 Type overview

ICS685 / ICS689 weighing terminals vary in the following:

Numeric keypad

Color display

Environment

Available as compact scale

Available as terminal and platform combination

ICS685

x x dry x x

Default equipment

ICS685 / ICS689 weighing terminals

Each weighing terminal offers the following interfaces:

• 1 serial interface RS232 (in Europe: 2 x RS232)

• 1 scale interface, analog or digital

ICS685k-.../f compact scales

The compact scales offer the following interfaces:

• 1 serial interface RS232 (in Europe: 2 x RS232)

• 1 scale interface SICSpro

Optional equipment

Two additional interfaces are possible, either communication interfaces or scale interfaces.

Optional interface

RS232

RS422/RS485

USB Device

USB Host

Ethernet

WLAN

Digital I/O

Analog scale

SICSpro scale

IDNet scale

COM1

Default

COM2

x x x x

– x

– x

COM3

x x x

– x x

– x

• RS232 usable as data interface or SICS scale

• RS422/RS485 usable as data interface or scale interface SICSpro

• SCL2 can be equipped with a scale interface or a communication interface (COM4)

– x

– x x

SCL2

x x

– x

ICS689

x x wet

– x

– x

– x x

SCL1

8 Introduction

1.2.2 Display

To meet your special requirements, different display layouts are available in the menu under Terminal

–> Device –> Display layout.

Straight weighing display – Default layout

1

Metrological data For details see following table

2

Weight value with star, sign and stability monitor For details see following table

3

Spanner icon: service needed For details see event and error messages

4

Battery symbol

5

Net/Gross

6

Unit

7

Indication of the soft key page (1/4) and navigation hint: use cursor keys < or > for scrolling soft key pages

8

Soft keys (factory setting, page 1)

9

Auxiliary data line

3 lines can be defined in the menu, specific to the weighing application

10

Symbol and info line

The contents is defined in the menu; here: Date & Time, Article

For details see following table

Introduction 9

10 Introduction

Straight weighing display – 3-line mode

• You can switch display layouts with the soft key or select the display layout in the

Terminal menu.

• The selected display layout is active for all applications.

Straight weighing display – Bargraph

In the auxiliary lines a graphic display of the scale capacity can be activated.

Prerequisite: In the Application menu Bargraph is activated for one of the auxiliary lines.

The bargraph indicates roughly which part of the scale capacity is already occupied and what capacity is still available.

In the example above, approximately 3/4 of the scale capacity is occupied, although the applied net weight isn’t really high. The reason therefore could be a high tare weight.

1.2.3 Display in Over/Under Checkweighing mode

In Over/Under Checkweighing mode (see Over/Under

Checkweighing or Checkcounting procedure

[

}

 55]) the display uses colors to indicate the

checkweighing status. Three different layouts can be selected in the menu or via soft key.

Default layout

Instead of the weight display a bargraph is displayed indicating target values.

The example shows the default color for a sample below the lower tolerance.

3-line mode

Tolerances and target weight are displayed in 3 lines.

The example shows the default color for a sample above the upper tolerance.

Color mode

The example shows the default color for a good sample.

• You can switch display layouts with the soft key or select the display layout in the

Terminal menu.

• The selected display layout is active for all applications.

Introduction 11

1.2.4 Display in Filling mode

In Filling mode (see Filling procedure [ }  55]), instead of the weight display, a bargraph and colors

indicate the filling status.

Too low

LOW

Tol–

HI

Tol+

As long as the weight is below the tolerance, a red bar is displayed.

Good

LOW

Tol–

HI

Tol+

Tol–

LOW

Target

Tol+

HI

When the weight approaches the good range, a second bar is displayed, in which the tolerance range is spread. This is an aid to exactly fill in the target weight.

Too high

When the weight exceeds the tolerance range, the color changes to yellow.

• You can switch display layouts with the soft key or select the display layout in the

Terminal menu.

• The selected display layout is active for all applications.

12 Introduction

Metrological data line

The metrological data is stored in the weighing platform. The weighing terminal only serves as indicator.

In the metrological data line the following information is displayed:

Symbol Information

Accuracy classes

,

,

,

Remark

Displayed only if the scale is approved according to the Weights and Measures guidelines

,

,

,

Weighing range information For multi range devices only and if the scale is approved according to the Weights and Measures guidelines

Maximum capacity

cap for NTEP only

Minimum capacity

Approved resolution

Displayed only if the scale is approved according to the OIML Weights and Measures guidelines

Displayed only if the scale is approved (OIML)

Display resolution

Approved weighing device

Please note for approved scales:

OIML: Displayed only if d is different from e

NTEP: Always displayed

Metrology display disabled for SICS scales, e.g.,

BBK422. Weights and Measures data must be indicated on a label near the weight display.

Weight value

The weight value can be marked with the following symbols:

Symbol Information

Calculated weight value

Remark

For example for average weighing results

Sign

Stability monitor

Non-approved last digit with e>d

For negative weight values

For unstable weight values

For approved scales only

The example shows the weight value for a scale with e=1g and d=0.1g.

The last, smaller digit is not approved.

Introduction 13

14 Introduction

Symbols and info line

In the symbols and info line the following information can be displayed:

Symbol Information

Scale number

Remark

Ddisplayed only if 2 or more scales are connected

I<–>I1

Weighing range

Weight below minimum weight

Average weighing

Automatic taring

For multi range or multi interval scales only

MinWeigh must be activated in the menu

Average must be activated in the menu

Auto Tare must be activated in the menu

Automatic clearing of the tare weight A­Clear Tare must be activated in the menu

Over/Under checkweighing to zero

To zero must be assigned to a soft key in the menu

Center of zero indication Availability depending on local Weights and

Measures regulations

Automatic APW (average piece weight) optimization

Totalization

APW optimization must be set to Auto

Totalization active

Fact needs to be done

Statistics

Internal database

External database active

WLAN connected

WLAN disconnected

LAN connected

Temperature check

Fact = Fully automatic calibration test.

When Fact is displayed: Ensure that the weighing platform is empty and wait until the calibration test is done automatically.

For ICS685k-.../f compact scales only.

Statistics active

Internal database active

Article information is stored externally. The internal database is inactive.

For ICS685k-.../f compact scales only

1.2.5 Keyboard

Function keys

Key

<

>

/

Name

Power

Clear

Switch

Zero

Tare

Info

Transfer

Cursor key

Cursor key

Cursor keys

Function in the operating mode

• Switching on and off

• Cancelling editing

• Clearing tare

• Leaving info page

• Leaving application

• Switching over weight unit

Function in the menu

• Cancelling editing

• Exiting menu

Clearing value

Clearing digit

• Setting scale to zero

• Clearing tare

• Taring scale

• Clearing previous tare

• Activating info screen

• Proceeding to the next info line / info page

• Freezing and releasing startup screen

• Transferring data to a printer or computer

• Navigating

Navigating

Navigating

• Re-editing

• Switching over from numerics to upper/lower case letters

• Confirming entry/selection

• Leaving menu item

• Back to the next higher menu level

• Entering menu item

• Navigating up/down

Introduction 15

16 Introduction

Soft keys

To meet your specific application requirements, ICS685 / ICS689 offer 16 soft keys which can be configured in the Terminal menu. The soft keys are divided into four lines (pages).

Factory setting ICS685

Page 1

Page 2

Reference n var here: 10 pieces

Reference n fixed here: 10 pieces

Weight/count Over/Under

Checkweighing

Totalizing

Page 3

Higher resolution Filling Database Memory

1)

Logout

2)

Display layout Switching scale

3)

Page 4

Page 4 is free for customer configuration.

When scrolling further after the last page, page 1 is displayed again.

Factory setting ICS689

Page 1

Page 2

Over/Under

Checkweighing

Database Filling Memory

1)

Page 3

Higher resolution Totalizing Classifying Logout

2)

Display layout Switching scale

3)

Reference n var here: 10 pieces

Reference n fixed here: 10 pieces

Page 4

Page 4 is free for customer configuration.

When scrolling further after the last page, page 1 is displayed again.

1)

The Memory soft key is not available if Memory mode is set to Off.

2)

The Logout soft key is available only if user management is active.

3)

The Switching scale soft key is available only if more than 1 scale is connected.

Operating soft keys

Press the key below the desired function.

APW (average piece weight)

Changing soft key line

Press the cursor keys < or > to switch from line to line.

Introduction 17

18 Introduction

Soft key options

Symbol Menu setting

Zero

Tare

Alibi memory

Switch scale x10 display Show the weight value with 10 times higher resolution

Transfer Data transfer to a printer or computer

Average weighing Start average weighing

ID1

ID2

Function

Zeroing

Taring

Calling up the optional alibi memory

Switching between the connected scales

Symbol Menu setting

APW

Function

Enter the average piece weight

APW optimization Reference weight optimization, only if activated in the menu and if a reference weight is determined

Totalizing Get sum of several weighings

Over/Under

Checkweighing

Filling

Enter Over/Under

Checkweighing parameters

Enter filling parameters

Enter identifications.

In the menu, another designation can be assigned to the keys.

Classifying Enter class parameters

Weight/count Switch between weight display and display of pieces

Save as article Save the current article parameters in the database

Database Show database

Custom input

ID3

Prompt 1,

Prompt 2,

Prompt 3

Ref n var

Ref n fix

Cons. number

Start a workflow.

In the menu, another designation can be assigned to the keys.

Determine the average piece weight, freely adjustable

Determine the average piece weight, fixed reference sizes

Custom input

Recall article

Logout

Display layout

Temperature check

Recall parameters from the database

Logout from the terminal

Switch between default weight display and 3-line mode

Check device temperature (only for

ICS685k-.../f and if activated in the menu)

Enter start value for printout with consecutive number

1.2.6 Alphanumeric input

When an alphanumeric input is requested, one of the following symbols is displayed in the right top edge of the display: for numeric input and special characters for input in upper case letters for input in lower case letters

• To activate the cursor in a text field, press .

• To switch between numerics and upper/lower case letters press Ç (Shift).

• Text entries work like, e.g., on a mobile phone. Up to four characters are assigned to the keys of the numeric keyboard.

• Entries must be confirmed with or soft key .

Example: Enter "ICS6x5"

1 Make sure that is displayed.

2 To enter letter "I" press key 4 three times.

3 To enter letter "C" press key 2 three times.

4 To enter letter "S" press key 7 four times.

5 Press Ç (Shift) twice to change to numerics

6 Enter number 6.

.

7 Press Ç (Shift) twice to change to lower case letters

8 To enter letter "x" press key 9 twice.

.

9 Press Ç (Shift) to change to numerics

10 Enter number 5.

11 Confirm entry with .

.

1.2.7 Barcode input

To make inputs easier, a barcode scanner can be connected.

Depending on the menu settings, the barcode scanner can be used either for a fixed or a free entry.

Fixed barcode entry

§ Communication –> COMx –> Mode is set to External input.

§ Communication –> COMx –> External input –> Destinaton is set to e.g., ID1.

To enter the selected data, e.g., ID1, just read the barcode.

ð The barcode entry is automatically recognized, e.g., as ID1.

Free barcode entry

§ Communication –> COMx –> Mode is set to External input.

§ Communication –> COMx –> External input –> Destinaton is set to e.g., Off.

Read the barcode and press the desired hard or soft key, e.g.,

ð The barcode entry is recognized, e.g., as tare preset or ID1.

or .

Introduction 19

1.2.8 Connections

ICS685 weighing terminal for dry environments

1 2 3 4

1

AC power supply or battery charging

3

Optional interface COM2

5 6

5

Optional weighing platform connection

SCALE 2 or optional data interface

ICS689 weighing terminal for wet environments

2

Standard interface COM1 (RS232)

4

Optional interface COM3 incl. digital scale interface SICSpro and SICS scale

6

Weighing platform connection SCALE1

1 2 3

4

8

7

6

5

1

Optional interface COM2

3

Standard interface COM1 (RS232) Pressure compensation

5

Pressure compensation

7

Verification securing seal

2

Optional interface COM3

4

Weighing platform connection SCALE 1

6

AC power supply or battery charging

8

Optional weighing platform connection

SCALE 2

20 Introduction

ICS689a-.../c

2

5

4

3

1

Optional interface COM2

3

Pressure compensation

5

Standard interface COM1 (RS232)

2

4

Weighing platform connection

AC power supply or battery charging

The verification securing seal is applied directly on the weighing terminal.

1.3 Application overview

1.3.1 Weighing applications

ICS685 / ICS689 weighing terminals offer various weighing applications for your special tasks.

• Straight weighing – just load a weight and read the result

• Average weighing (dynamic weighing) for weighing restless samples, e.g., animals

• Counting

– Counting of discrete samples like screws, sheet, ...

– Measuring of non-discrete samples like lengths, areas, volumes, ...

• Over/Under Checkweighing and Filling

– Over/Under Checkweighing of different samples of a kind

– Filling in liquids or poudery products to a target quantity

• Classifying

• Totalizing – also for Counting and Over/Under Checkweighing or Filling results

• For each application, the contents of the auxiliary lines in the display and the printout can be configured individually.

• Counting, Over/Under Checkweighing or Filling and Totalizing can be combined.

Introduction 21

1.3.2 Advanced features

Overview

ICS685 / ICS689 weighing terminals offer some advanced features to make operation easier, safer and traceable:

• User management

• Prompting

• Database

• Statistics (as part of the totalizing function)

• Routine test and Routine test log

• Corner load test and Corner load log

• Calibration log file

• Memory (Alibi memory or transaction memory)

User management

The user management of the ICS685 / ICS689 allows you to manage up to 20 users by:

• User name and User ID

• User profile (operator or supervisor)

• User language

• User password

• User specific keys

• When user management is activated, any access to the terminal is protected by password.

• User management can be configured in the menu under Terminal –> User management.

Login/logout with user management is described in "Login/Logout [ }  29]".

Prompting

The device offers 6 predefined prompts for frequently used workflows. In addition, up to 3 customer specific workflows can be defined to guide the operator.

• Prompts can be configured in the menu under Application –> Prompting.

Operation with prompts is described in Prompt overview [

}

 36] and following.

22 Introduction

Database

The device offers an internal database of up to 5,000 data records for frequently used weighing goods.

Each record may contain the following data:

• Article information data

• Weight values

• Piece counting parameters

• Checkweighing parameters

• Filling parameters

• Totalization parameters

Editing the database is described in Creating a new article [

}

 118] and following.

• Once application parameters are entered they can be stored in the database as well.

• To edit the database comfortably on your computer, the optional DatabICS software is available

(www.mt.com/ind-databics). When using DatabICS, up to 30,000 data records are available.

Statistics

The device offers statistical evaluation of your weighing series.

The following statistical values may be determined:

• Standard deviation

• Standard deviation (good)

• Mean value

• Mean value (good)

• Max. value

• Min. value

• Median

• % ratio per class

• # per class

To evaluate statistics comfortably on your computer, the optional DatabICS software is available

(www.mt.com/ind-databics).

Introduction 23

24 Introduction

Routine test / Cornerload test

For optimum weighing results the device supports routine calibration and routine cornerload tests. The test results are stored in the corresponding log files.

You can configure routine tests by:

• Interval (days)

• External test

• Internal test (for ICS685k-.../f only)

For the external tests you can specify the following:

• Test weight (value)

• Weight name (to make sure you always use the same weight)

• Tolerance

• The routine test and cornerload test can be configured separately for each connected scale in the menu under Maintenance –> Scale test.

Performing the tests and viewing/printing/transferring the log files is described in "Performing routine test [

}

 121]" and following.

Calibration log file

All calibration results are stored in the calibration log file.

How to view/print/transfer the calibration log file is described in "Calling up calibration log file [

}

 124]".

1.4 Commissioning

1.4.1 Selecting the location

The correct location is crucial for the accuracy of the weighing results.

1 Select a stable, vibration-free and, if possible, a horizontal location for the weighing platform.

ð The ground must be able to safely bear the weight of the fully loaded weighing platform.

2 Observe the following environmental conditions:

ð No direct sunlight

ð No strong drafts

ð No excessive temperature fluctuations

1.4.2 Levelling

Levelling of weighing platforms

Only weighing platforms that have been levelled precisely horizontally, provide accurate weighing results. Weights and Measures approved weighing platforms have a level bubble to simplify levelling.

Turn the adjustable feet of the weighing platform until the level bubble’s air bubble is inside the inner circle.

Levelling of compact scales ICS685-.../f

On compact scales levelling can be done in an easier way.

1 2

3

1 2

1 Turn the compact scale upside down.

2 Screw in the 2 adjustable feet (2) on the terminal side of the weighing platform.

3 Turn over the compact scale to its normal position.

4 Level the compact scale by turning the other 2 adjustable feet (1) of the weighing platform until the level bubble is inside the inner circle.

5 Screw out the feet (2) of the weighing platform until they have contact with the table.

The adjustable foot (3) of the weighing terminal is screwed out for 7 mm at the factory and needs not be adjusted for levelling.

Introduction 25

1.4.3 Weighing platform connection

Analog weighing platforms

Call the METTLER TOLEDO service technician to connect an analog weighing platform to the ICS685g /

ICS689g weighing terminal.

Weighing platforms with digital scale interface

Connect the weighing platform connector to the ICS685i / ICS689i or ICS685s / ICS689s weighing terminal.

• If you have ordered an approved weighing system consisting of an ICS685s weighing terminal and an approved PBD555 weighing platform, the approval was done in the factory (not for the

US market).

• You can disconnect the weighing platform from the ICS685s / ICS689s or ICS685i / ICS689i weighing terminal of an approved weighing system without violating the approval.

If another weighing platform is connected to the weighing terminal, the system is not approved.

If the weighing platform of the approved system is connected again, the approval is valid again.

• If you have ordered an approved weighing system consisting of an ICS685s / ICS689s weighing terminal and an approved PBK/PFK weighing platform, the approval was done in the factory (not for the US market).

• If you have connected a non-approved weighing platform and want to have the system approved, call the METTLER TOLEDO service technician.

1.4.4 Power supply connection

CAUTION

Risk of electric shock!

a) Before connecting the power supply, check whether the voltage value printed on the label corresponds to your local system voltage.

b) Do not, under any circumstances, connect the device if the voltage value on the label deviates from the local system voltage.

c) Make sure the weighing platform has reached room temperature before switching on the power supply.

Plug the power plug into the power socket.

ð After it has been connected, the device runs a self-test. The device is ready to operate when zero appears on the display.

26 Introduction

1.4.5 Handling the storage battery

Battery symbol

The battery symbol shows the current charging status of the storage battery.

• One segment corresponds with approx. 25 % capacity.

• If the symbol flashes, the storage battery has to be charged.

• During charging the segments are "running" until the battery is fully charged and all segments light up continuously.

Note the following when operating a device with a built-in storage battery:

• Before the first operation charge the storage battery for at least 3 hours.

• The operating life depends on the intensity of use, the configuration, and the connected scale. For details

concerning ICS685, see "Operating life with battery [ }

 132]", or concerning ICS689, see "Operating life with battery [ }  138]".

• The charging time of the storage battery amounts to 4 to 5 hours. The storage battery is protected against overcharging.

• The storage battery has a service life of 500 to 1,000 charging/discharging cycles.

CAUTION

Charging the storage battery below 0° C (32 °F) or above 40 °C (104 °F) is prevented by the charging electronics!

a) Make sure that the temperature is within the range of 0 °C to 40 °C (32 °F to 104 °F) to charge the storage battery.

CAUTION

Danger of soiling because the charger for the storage battery is not protected according to IP69K!

a) Do not charge the device in humid or dusty rooms.

b) After the storage battery has been charged, close the cover cap of the charging socket on the device.

Recommended use of the storage battery

The characteristics mentioned above are only valid if the following recommendations are observed:

• Change the battery as soon as the warning message "Low battery" appears and the battery symbol starts flashing. When the message appears, you still have enough time (at least 10 minutes), to complete your current task.

• For optimum battery performance, operate the device with built-in storage battery at an ambient temperature range of 10 °C to 30 °C (50 °F to 86 °F). This also applies to discharging the battery.

Introduction 27

Changing battery (ICS685 only)

2.

1.

1 Unlock the battery by moving the slider away from the battery and remove the discharged battery.

2 Insert the fully charged battery and secure it by moving the slider towards the battery.

With optional IP65 protection, the battery is not accessible from the outside. Please call the

METTLER TOLEDO service technician.

1.4.6 Use in hygienically sensitive areas

ICS689 weighing terminals are easy to clean and are designed to be used in the food industry.

ICS689 features

• Protection degree IP68/69k

• Terminal housing and load plate made of stainless steel

• No open threads

• No screws with recesses

• Keypad made of PET with a smooth surface

• Reduced horizontal surfaces

• Continuous welding seams

28 Introduction

2 Operation

2.1 Switching on/off

Switching on

Press .

ð For a few seconds the device shows a start-up screen with device name, software version, serial number of the weighing terminal and the Geo Code value.

• You can freeze the start-up screen by pressing .

• When you start a compact scale, the metrology line shows whether it is approved or not. If you have ordered an approved weighing system, approval has been done in the factory already (not for the US market).

• With ICS685k-.../f compact scales ensure that the device is at room temperature before switching on. To ensure accurate weighing results, wait 15 minutes after switching on before

starting weighing operation.

Switching off

Press .

ð Before the display goes out, ­OFF­ appears briefly.

Resetting

Press and hold for approx. 5 seconds.

ð The device is switched off.

2.2 Login/Logout

When user management is activated in the Terminal menu, a login/logout procedure is required. The login screen is displayed after switching on or logging out.

Login

1 Select your name using the cursor keys ∧ / ∨ and confirm with soft key.

2 Enter your password and confirm with soft key.

ð The weight display appears.

Logout

1 Press soft key.

ð A safety prompt is displayed.

2 Press soft key.

ð The login screen is displayed, the current user is logged out.

Always log out when leaving the terminal in order to prevent unauthorized persons from working on it.

2.3 Straight weighing

1 Place weighing sample on the scale.

2 Wait until the stability monitor disappears.

3 Read the weighing result.

Operation 29

2.4 Switching units

If an additional second weight unit is configured in the menu, it is possible to switch back and forth between the two weight units.

Press .

ð The weight value is displayed in the second unit.

• Possible units are g, kg, oz, lb, lb-oz, t and PCS in piece counting.

• When in the menu Scale –> Display unit & Resulution –> Unit roll is set to On, the weight value can be displayed in all available weight units by repeatedly pressing

.

2.5 Zeroing / Zero point correction

Zeroing corrects the influence of slight changes on the load plate or minor deviations from the zero point.

Manual

1 Unload scale.

2 Press .

ð Zero appears in the display.

Automatic

In case of non-approved scales, the automatic zero point correction can be deactivated in the menu or the zero range can be changed. Approved scales are set fixed at 0.5 d per second.

• The zero function is only available within a limited weighing range.

• After zeroing the scale, the whole weighing range is still available.

2.6 Weighing with tare

2.6.1 Taring

Place the empty container on the scale and press

ð The zero display and the symbol

appear.

ð The tare weight remains stored until it is cleared.

.

2.6.2 Clearing the tare

Press .

ð The symbol

goes out, the gross weight appears in the display.

If the symbol is displayed, i.e., the tare function Auto clear tare is activated in the

Scale menu, the tare weight is automatically cleared as soon as the scale is unloaded.

2.6.3 Automatic clearing the tare

A tare weight is automatically cleared when the scale is unloaded.

Prerequisite

The symbol is displayed, i.e., the tare function Auto clear tare is activated in the Scale menu.

The tare weight must be heavier than 9 scale divisions.

30 Operation

2.6.4 Automatic taring

If you place a weight on an empty scale, the scale tares automatically and the symbol is displayed.

Prerequisite

The symbol is displayed, i.e., the tare function Auto tare is activated in the Scale menu.

The weight to be tared automatically, e.g., packaging material, must be heavier than 9 scale divisions.

2.6.5 Chain tare

With this function it is possible to tare several times if, e.g., cardboard is placed between individual layers in a container.

§ The tare function Chain tare is activated in the Scale menu.

1 Place the first container or packaging material on the scale and press .

ð The packaging weight is automatically saved as the tare weight, the zero display and the symbol

appear.

2 Load the sample and read/print out the result.

3 Place the second container or packaging material on the scale and press again.

ð The total weight on the scale is saved as the new tare weight. The zero display appears.

4 Load the sample in the second container and read/print the result.

5 Repeat steps 3 and 4 for other containers.

Operation 31

2.6.6 Tare preset

For established container weights enter the tare weight numerically or via barcode / SICS command. Thus, you do not have to tare the empty container.

The entered tare weight is valid until a new tare weight is entered or the tare weight is cleared.

Tare preset with numeric entry

1 Enter the known tare weight and press to confirm.

ð The weight display shows the negative tare weight and the symbol

2 Place the full container on the weighing platform.

ð The net weight is displayed.

appears.

Tare preset with barcode entry

§ For barcode use, Tare preset is selected as destination for external input in the menu under

Communication –> COMx –> External input –> Destination.

1 Enter the known tare weight via barcode.

ð The weight display shows the negative tare weight and the symbol

2 Place the full container on the weighing platform.

ð The net weight is displayed.

Tare preset with SICS command from a connected computer

appears.

1 Enter the known tare weight on the computer using the SICS command TA_Value_Unit.

ð The weight display shows the negative tare weight and the symbol

appears.

2 Place the full container on the weighing platform.

ð The net weight is displayed.

32 Operation

2.7 Displaying information

Up to 9 different items can be configured in the menu for the key. Depending on the configuration in the menu under  Terminal –> Device –> Keyboard –> Info key, the following data can be assigned in any order, e.g.,

• Date & Time

• Weight values

• Identifications

• Article information

• Application parameters

• Device information

• User data

• Serial numbers and software versions

• Network information

On the second and third info page, system and contact information can be displayed.

1 Press .

ð The (first) info page is displayed.

2 Press again.

ð The next info screen is displayed.

3 To leave the info screens, press .

An info screen is displayed until is pressed again or until is pressed.

2.8 Printing results

If a printer or computer is connected, weighing results and other information can be printed out or transferred to a computer.

Press .

ð The defined data is printed out or transferred to the computer.

• The printout content can be defined in the menu under Communication –> COMx –>

Define Templates. The template has to be assigned to the printout in the

Application menu.

• If in the Application menu Memory mode is set to Alibi or Transaction, the weighing result is stored in the memory when pressing .

Printing without pressing a key (clever print)

§ In the menu Application –> Clever print –> Activate is set to On.

§ To initiate the next printout, the weight must drop below the set threshold.

1 Put the weighing sample on the load plate.

ð When a stable weight value is reached, the result is printed automatically.

2 Remove the weighing sample from the load plate and load the next weighing sample.

ð When the weight value has dropped below the set threshold, the next stable weight value is printed automatically.

Operation 33

34 Operation

Printout with consecutive number

The device offers the possibility to number the weighings on the printout.

§ In the selected template Consecutive number is assigned to a line.

§ To define a start value, a soft key must be defined as Consecutive number (

) in the menu under  Terminal –> Device –>

Keyboard –> Soft keys.

1 To enter a start value for the consecutive number, press the soft key

.

2 Enter the desired start number and confirm with .

ð The weighing results are printed out with a consecutive number, beginning at the entered start number.

• If no start value is entered, the consecutive number will start with 1.

• The consecutive number can be displayed in the auxiliary lines as well (Application –

> ... –> Auxiliary lines –> Consecutive number)

2.9 Average (dynamic) weighing

With the average weighing function, it is possible to weigh moving weighing samples such as animals. If this function is activated, is displayed in the info line. With average weighing, the scale calculates the mean value from weighing operations within a certain time interval.

Start via soft key (factory setting)

§ Weighing sample heavier than 9 scale divisions.

1 Place the weighing sample on the scale.

2 Press the soft key to start average weighing.

ð During average weighing, stars appear in the display, and the average result will be displayed with the symbol .

3 Unload the scale to begin a new average weighing operation.

With automatic start

§ Application ­> Average ­> Mode –> Auto is selected in the menu.

§ Weighing sample heavier than 9 scale divisions.

1 Place the weighing sample on the scale.

ð Average weighing starts automatically.

ð During average weighing, stars appear in the display, and the average result will be displayed with the symbol .

2 Unload the scale to start a new average weighing operation.

2.10 Working with identifications

Weighing series can be assigned with 3 identification numbers ID1, ID2 and ID3 with up to 40 numeric characters that are also printed out in the protocols. If, for example, a customer number and a batch number are assigned, it can be clearly seen in the protocol which batch was weighed for which customer.

Direct entry

§ At least one of the soft keys ID1, ID2 or ID3 is activated in the menu under Terminal –>

Device –> Keyboard –> Soft keys.

§ To display the identification in the auxiliary lines, ID1,  ID2 or ID3 must be activated in the menu under Application –> ... –> Auxiliary lines for each application.

1 Press the desired soft key , , .

ð The ID entered last is displayed.

2 Enter the ID and confirm with .

ð The entered ID is assigned to the following weighings until the ID is changed.

Barcode use (for one identification only)

§ ID1, ID2 or ID3 is selected as destination for external input in the menu under Communication

– COMx –> External input –> Destination.

§ To display the identification in the auxiliary line, ID1,  ID2 or ID3 has to be activated in the menu under Application –> ... –> Auxiliary linesfor each application.

Scan the ID.

ð The ID is assigned to the following weighings until a new ID is scanned.

Using SICS command set (up to three identifications)

§ To display the identification in the auxiliary line, ID1,  ID2 or ID3 has to be activated in the menu under Application –> ... –> Auxiliary linesfor each application.

Send the ID command (I12, I13 or I14) from a PC.

ð The ID is assigned to the following weighings until a new ID is sent.

In the Terminal menu a designation can be given to the identification keys ID1, ID2 and ID3 which is displayed as soft key. So you clearly see which information is asked, e.g., Batch instead of ID2.

2.11 Working in a higher resolution

The weight value can be displayed in a higher resolution continuously or when called.

§ Soft key x10 Display is activated in the Terminal menu.

Press soft key .

ð The weight value is displayed in at least 10x higher resolution and is marked with the symbol .

ð The higher resolution is displayed for 3 seconds.

With non-approved weighing platforms, the weight value in a higher resolution can permanently be displayed in the Auxiliary line.

Operation 35

2.12 Switching scales

§ At least two scales are connected to the weighing terminal.

§ The soft key Switch scale is activated in the Terminal menu.

Press the soft key to switch to the next scale.

ð The current active scale is displayed in the symbol and info line on the top edge of the display. In the soft key symbol, the number has changed.

2.13 Working with a prompt

2.13.1 Prompt overview

The device offers prompts for frequently used workflows. You can select either from the six predefined prompts or create your own prompt. The weighing terminal will then lead you from step to step.

In the Application menu the following prompts can be activated:

Tare/Sample – counting with first taring and then determining the average piece weight

Sample/Tare – counting with first determining the average piece weight and then taring

Hands free – counting without pressing any key

Multi tare – taring several containers with the same tare weight

Additive tare – adding different tare values

Take away – checkweighing out of a container

• During prompting, no other soft keys are available.

• To start a prompt, at least one of the soft keys Prompt 1, Prompt 2, Prompt 3 must be activated in the Terminal menu.

• In the Application menu, these soft keys can be denominated according to your specific task.

36 Operation

2.13.2 Tare/Sample

This prompt will guide you through piece counting with first taring and then determining the average piece weight.

1 Check the current reference size which is indicated on the soft key (Ref N var).

2 If necessary, change the reference size, see Counting section.

3 Press the prompt soft key.

ð In the soft key line the instructions for the first step are displayed.

4 Load the tare weight and confirm with the indicated soft key.

ð In the soft key line the instructions for the next step are displayed.

5 Load the reference parts and confirm with the indicated soft key.

ð The display unit changes to PCS and the soft key line changes.

6 Load the weighing samples and read the number of pieces.

7 To restart counting with a new reference, press the indicated soft key.

ð Cleared is displayed briefly before the first prompt is displayed again.

8 Repeat steps 4 to 7 for other references.

9 To leave piece counting, press .

ð Cleared is displayed briefly.

If a printer is connected, each individual result can be printed out by pressing .

Operation 37

2.13.3 Sample/Tare

This prompt will guide you through piece counting with first determining the average piece weight and then taring.

1 Check the current reference size which is indicated on the soft key (Ref n var).

2 If necessary, change the reference size, see Counting section.

3 Press the prompt soft key.

ð In the soft key line the instructions for the first step are displayed.

4 Load the reference parts and confirm with the indicated soft key.

ð The display unit changes to PCS and the soft key line changes.

5 Load the tare weight and confirm with the indicated soft key.

ð In the soft key line the instructions for the next step are displayed.

6 Load the weighing samples and read the number of pieces.

7 To restart counting with a new reference, press the indicated soft key.

ð Cleared is displayed briefly before the first prompt is displayed again.

8 Repeat steps 4 to 7 for other references.

9 To leave piece counting, press .

ð Cleared is displayed briefly.

If a printer is connected, each individual result can be printed out by pressing .

38 Operation

2.13.4 Hands free

This prompt will guide you through piece counting without pressing a key.

1 Press the prompt soft key.

ð In the soft key line the instructions for the first step are displayed.

2 Load the tare weight.

ð When the weight is stable, an automatic taring is carried out.

ð In the soft key line the instructions for the next step are displayed.

3 Load the indicated number of reference parts.

ð The average piece weight is determined automatically.

ð The weight unit changes to PCS and the soft key line changes.

4 Load the weighing samples and read the number of pieces.

Restarting piece counting

To restart counting with a new reference, press the indicated soft key.

ð Cleared is displayed briefly before the first prompt is displayed again.

Leaving piece counting

To leave piece counting, press .

ð Cleared is displayed briefly.

Operation 39

2.13.5 Multi tare

This prompt will guide you through taring a bundle of containers with the same known tare weight.

1 Press the prompt soft key.

ð The number of containers (n) is highlighted.

2 Enter the number of containers and confirm entry with the soft key .

ð The tare value of a single container is highlighted.

3 Enter the known tare weight of a single container and confirm entry with the soft key .

ð When all entries are made, the weight is shown in the display.

E.g., with a bundle of 6 containers of 0.4 kg each, a PT (preset tare) value of 2.4 kg is displayed for the whole bundle.

4 Weigh the bundle.

ð The net weight of the bundle is displayed without extra taring.

5 To leave prompting, press .

ð Cleared is displayed briefly.

40 Operation

2.13.6 Additive tare

This prompt will guide you through taring e.g., a pallet with containers on it with known tare weights.

1 Press the prompt soft key.

ð A table for tare weights is displayed.

2 Enter the tare weights and confirm each tare weight with .

ð Each confirmation creates a new tare record.

3 When all tare weights are entered, press soft key to finish the entry.

ð The total of all tare weights is displayed as pretare value indicated with PT.

4 Weigh the pallets.

ð The net weight of the pallet is displayed without extra taring.

5 To leave prompting, press .

ð Cleared is displayed briefly.

Soft key functions

(Soft) key

/

Meaning

selecting a tare weight editing an existing tare weight creating a new tare weight deleting the selected tare weight deleting all tare weights

Operation 41

2.13.7 Take away

This prompt will guide you through weighing the same items into a container or weighing out of a container without pressing a key between the actions.

1 Press the prompt soft key.

ð The screen to enter target values is displayed.

2 Enter target values as described in the Checkweighing section.

For weighing in, enter a positive target value. For weighing, out enter a negative target value.

ð New target set! is displayed briefly.

3 For weighing in, place the empty container on the scale.

For weighing out, place the full container on the scale.

4 Press to tare the container.

5 For weighing in, place the checkweighing material into the container.

For weighing out, remove the checkweighing material from the container.

ð If the applied/removed weight or the applied/removed amount is within the tolerance values, taring is carried out automatically.

The next item can be weighed in/removed.

6 To leave prompting, press .

ð Cleared is displayed briefly.

• When using an item which is too light or too heavy, taring must be carried out automatically.

• Select the Auto print feature to generate an automatic printout when the weight is within or outside of tolerances.

42 Operation

2.14 Memory log files

2.14.1 Calling up memory log file

Only weighing results confirmed with are stored in the memory log file.

Overview

§ Memory mode is set to Alibi or

Transaction under Application –>

Memory.

Press the soft key or select Memory in the Quick

Select menu with the cursor keys / and confirm with .

ð The Alibi records of the last weighing operations are displayed.

Soft key functions

Soft key Meaning

Cancelling

Searching the Alibi memory

Viewing selected Alibi record in detail

Printing Alibi records

To the last Alibi record

Searching is possible by all data fields, except the Custom field.

Operation 43

2.14.2 Searching and printing memory records

For searching a memory record the device offers 3 search fields with individual search criterions each, e.g., data, weight values, article info. For each search field the desired range can be specified.

1 In the alibi overview press the soft key.

ð The search window opens.

2 Select item for Search field 1.

3 Use the cursor key to proceed to the corresponding From field.

4 Enter the start value for the search field.

5 Use the cursor key to proceed to the corresponding To field.

6 Enter the end value for the search field.

7 Use the cursor key to proceed to the next search field.

8 Repeat steps 2 to 7 for Search field 2 and

Search field 3, if desired.

9 Start the search with the soft key.

ð The matching alibi records are displayed.

10 To print the search result, press the soft key.

2.14.3 Memory backup with USB Host

If a USB Host interface is installed you are able to download your memory data to a USB stick. The data is stored as .csv file which can easily be opened in Microsoft Excel for any kind of analysis.

1 In the alibi overview press the soft key .

2 Enter the search parameters as described in Searching and printing memory records [

}

 44].

3 Make sure that a USB stick is connected to the USB Host interface.

4 Press the soft key (USB).

ð A window opens to edit the backup file.

5 Enter the file name and delimiter (, or ; or :).

6 Press the soft key (USB) again.

ð The memory data is downloaded to the USB stick.

ð Backup is in progress xx% is displayed.

7 When the backup is finished, disconnect the USB stick and copy the data to your PC.

44 Operation

2.15 Cleaning

WARNING

Risk of electric shock

a) Before cleaning, unplug the power plug in order to disconnect the terminal from the power supply.

b) Cover open connectors with protective caps.

Cleaning of the ICS685 (dry environments)

• Clean the optional protective cover separately. The protective cover is dishwasher-safe.

• Take off the load plate and remove any dirt and foreign substances which may have collected underneath. Do not use any hard objects to prevent scratching the surface.

• Do not disassemble the weighing device.

• Remove any remaining detergent with a wet cloth.

• Observe all existing regulations on cleaning intervals and permissible cleaning agents.

• In case of a windshield, we recommend to clean it with a glass cleaner each day of usage in order to prolong the durability.

Cleaning of the ICS689 (wet environments)

These devices are designed to be used in a wet environment. Depending on the environment and the cleaning procedures, we suggest appropriate weighing platforms with different types of load cells. The following table provides a detailed overview of recommended environments and suitable cleaning procedures.

Terminal

ICS689

IP68/IP69k

Weighing platform

Hermetically sealed stainless steel load cell

IP68/IP69k IP rating

Environment

Short time wet (30 min / day)

Part time wet (120 min/day)

Permanently wet

Cleaning procedure

Wet wipe down

Light hose down < 5 l/min,

20 kPa

Light wash down < 12.5 l/min,

30 kPa

Heavy wash down, high pressure water and steam jet up to 10000 kPa

Cleaning detergents

Mild detergents

Other detergents in accordance with the manufacturer's specifications and instructions x x x x x x x x x x x x x x x x x x

Operation 45

• Clean the optional protective cover separately. The protective cover is dishwasher-safe.

• Replace the protective cover regularly.

• Take off the load plate and remove any dirt and foreign substances which may have collected underneath. Do not use any hard objects to prevent scratching the surface.

• Do not disassemble the weighing device.

• Remove any remaining detergent by rinsing with clear water.

• To prolong the lifetime of the load cell, dry it with a soft lint-free cloth immediately after cleaning.

• Observe all existing regulations on cleaning intervals and permissible cleaning agents.

Cleaning of other weighing platforms not described in this user manual

Make sure to observe the cleaning instructions for the connected weighing platform. The weighing platform may not be designed for the environments and cleaning procedures described above!

2.16 Verification test

The weighing instrument is verified if:

• the accuracy class is displayed in the metrological line,

• the approval readability is shown with "e = readability",

• it bears an official verification mark, e.g., the green M sticker (OIML),

• the validity is not expired.

The weighing instrument is also verified if:

• the metrological line shows "Approved scale",

• labels with the metrological data are placed near the weight display,

• the securing seal is not tampered with,

• it bears an official verification mark, e.g., the green M sticker (OIML),

• the validity is not expired.

The period of validity is country-specific. It is in the responsibility of the owner to renew verification in due time.

Strain gauge weighing platforms

Strain gauge weighing platforms use a Geo Code to compensate gravitational influence. The manufacturer of the weighing instrument uses a defined Geo Code value for verification.

1 Check if the Geo Code in the instrument corresponds with the Geo Code value defined for your location.

ð The Geo Code value is displayed when you switch on the instrument.

ð The Geo Code value for your location is shown in the Appendix.

2 Call the METTLER TOLEDO service technician if the Geo Code values do not match.

46 Operation

3 Counting

3.1 Counting parts into a container

§ The soft keys Ref N var (

) and/or Ref N fix ( ) are activated in the menu under

Terminal –> Device –> Keyboard –> Soft keys (if not shown by default).

1 Place the empty container on the scale and press .

ð The container is tared, the zero display and the symbol NET appear.

2 Place the number of reference parts on the scale as indicated on the soft key or and press the corresponding soft key.

ð The scale determines the average piece weight and then shows the number of reference pieces.

3 Add more parts to the container until the required number of pieces is reached.

4 When piece counting is completed, press to clear the reference.

ð The scale is ready for the next weighing or counting operation.

• The average piece weight remains saved until is pressed or a new average piece weight is determined.

• With or soft key (Weight count) you can switch between the number of pieces and the weighing units preset.

• The average piece weight (APW), for example, the weight of an individual reference unit, can be displayed on the info page or in the auxiliary line.

• If Auto clear APW is set to On in the menu under Application –> Counting, the average piece weight is automatically cleared after each counting operation.

• The achieved counting accuracy can be displayed in the auxiliary lines under Application

–> Counting –> Auxiliary lines.

3.2 Counting parts out of a container

§ The soft keys Ref N var (

) and/or Ref N fix ( ) are activated in the menu under

Terminal –> Device –> Keyboard –> Soft keys (if not shown by default).

1 Place the full container on the scale and press .

ð The container is tared, the zero display and the symbol NET appear.

2 Remove the number of reference parts out of the container as indicated on the soft key or and press the corresponding soft key.

ð The scale determines the average piece weight and then shows the number of reference pieces removed, together with a minus sign.

3 Remove more parts out of the container until the required number of pieces is reached.

4 When piece counting is completed, press to clear the reference.

ð The scale is ready for the next weighing or counting operation.

Counting 47

3.3 Determining the parts in a full container

When you know the tare weight of the container, the number of parts in the container can be determined.

§ The soft keys Ref N var (

) and/or Ref N fix ( ) are activated in the menu under

Terminal –> Device –> Keyboard –> Soft keys (if not shown by default).

1 Place the number of reference parts on the scale as indicated on the soft key or and press the corresponding soft key.

ð The scale determines the average piece weight and then shows the number of reference pieces.

2 Enter or scan with a barcode reader the known tare weight and press

ð The weight display shows the negative tare weight and the symbol

3 Place the full container on the weighing platform.

ð The number of pieces in the container is displayed.

to confirm.

appears.

3.4 Counting with a known average piece weight

§ The soft key APW (Average Piece Weight,

) is activated in the menu under Terminal –>

Device –> Keyboard –> Soft keys (if not shown by default).

Enter the known average piece weight and press the soft key .

ð The scale changes the unit to PCS.

The rest of the counting procedure is as described in Counting parts into a container [

}

 47].

3.5 Changing reference quantity

3.5.1 Free reference quantity

§ The soft key Ref N var ( ) is activated in the menu under Terminal –> Device –>

Keyboard –> Soft keys.

§ In the Application –> Counting menu, Fixed ref. size is set to Off.

1 Place any number of reference parts on the scale.

2 Enter the number of reference parts and press the soft key .

ð The scale determines the average piece weight and then shows the number of pieces. In the soft key

the new number of reference parts is indicated.

The rest of the counting procedure is as described in Counting parts into a container [ }  47].

48 Counting

3.5.2 Selecting reference quantity out of a set

With soft key the following set of reference quantities is available: 5, 10, 20, 50, 100.

§ The soft key Ref N fix (

) is activated in the menu under Terminal –> Device –>

Keyboard –> Soft keys.

1 Place the desired number of reference parts (5, 10, 20, 50, 100) on the scale.

2 Press and hold the soft key until the soft key line changes.

3 Press the soft key for the desired number of reference parts.

ð The scale determines the average piece weight and then shows the number of pieces.

ð In the soft key

the new number of reference parts is indicated.

The rest of the counting procedure is as described in Counting parts into a container [

}

 47].

3.6 Counting with reference weight check

The reference weight check ensures that the reference weight is high enough to lead to a good counting result.

§ At least one of the soft keys Ref N var (

), Ref N fix ( ) or APW ( ) is activated in the menu under Terminal –> Device –> Keyboard –> Soft keys.

§ Ref. weight check is set to On under Application –> Counting.

1 Determine the average piece weight as described in "Counting parts into a container [ }  47]"

ð If the average piece weight is not sufficient, Add x PCS appears.

2 Add the displayed number of pieces.

ð The average piece weight is determined again with the larger reference quantity.

The rest of the counting procedure is as described in "Counting parts into a container [

}

 47]".

The tolerance for the reference weight check can be modified in the menu under Application

–> Counting –> Ref. weight –> Ref. weight check.

Counting 49

3.7 Reference optimization

3.7.1 Automatic reference optimization

The greater the reference quantity, the more accurately the scale determines the number of pieces.

§ The soft keys Ref N var (

) and/or Ref N fix ( ) are activated in the menu under

Terminal –> Device –> Keyboard –> Soft keys.

§ In the Application –> Counting menu, APW optimization is set to Auto, the symbol appears in the display.

1 Place the indicated number of reference parts on the scale and press the soft key or .

2 Place additional reference parts on the scale. The maximum for the additional reference parts cannot be larger than the original sample.

ð The scale automatically optimizes the average piece weight with the larger number of reference parts.

The rest of the counting procedure is as described in Counting parts into a container [

}

 47].

3.7.2 Manual reference optimization

The greater the reference quantity, the more accurately the scale determines the number of pieces.

§ The soft keys Ref N var (

) and/or Ref N fix ( ) are activated in the menu under

Terminal –> Device –> Keyboard –> Soft keys.

§ In the Application –> Counting menu, APW optimization is set to Soft key.

§ In the Terminal –> Device –> Keyboard –> Soft keys menu, the soft key APW optimization is activated.

1 Place the indicated number of reference parts on the scale and press the soft key or .

2 Place additional reference parts on the scale and press soft key .

ð The scale automatically optimizes the average piece weight with the larger number of reference parts.

The rest of the counting procedure is as described in Counting parts into a container [

}

 47].

3.8 Counting with automatic reference determination

§ In the Application –> Counting menu, Autosampling is set to On.

Place the indicated number of reference parts on the scale.

ð The scale automatically determines the average piece weight and then shows the quantity.

The rest of the counting procedure is as described in Counting parts into a container [

}

 47].

Pressing the soft key (Ref n VAR) or (Ref n FIX), the last average piece weight is cleared and the current weight is set as the new reference weight.

50 Counting

3.9 Counting with custom unit

The device offers the option to derive other physical variables from the weight of the sample, e.g., length, area, volume.

Unit and format of the physical variable can be defined in the Application –> Counting menu.

Prerequisite

In the Application –> Counting menu the following settings are made:

Unit type is set to Custom unit

• For Unit name the desired unit is entered, e.g., m, qm, l, $, Euro

• For Unit format the desired resolution is entered, e.g., 0.02 to count coins of 2 Cents and show the result in Euro

Weighing reference quantity

Place the indicated reference quantity on the scale and press soft key (Ref n FIX) or (Ref n VAR).

ð The scale determines the reference weight and then shows value and unit of the physical variable.

The rest of the measuring procedure is as described earlier.

Entering the known weight of the unit

Enter the known weight of the unit and press soft key .

ð The scale determines the reference weight and then shows value and unit of the physical variable.

The rest of the measuring procedure is as described earlier.

Counting 51

3.10 Counting with reference and bulk scale

3.10.1 Weighing systems with two or more scales

ICS685 / ICS689 can handle a weighing system with up to 4 scales.

There are two possibilities for counting with a scale system:

• Counting with reference scale and bulk scale: e.g., a high precision scale for determining the reference and a floor scale for counting large quantities.

• Counting with auxiliary scales: e.g., a high precision scale for counting small parts and a floor scale for counting bigger parts.

3.10.2 Counting with reference and bulk scale

§ At least one of the soft keys Ref N var (

), Ref N fix ( ) or APW ( ) is activated under Terminal –> Device –> Keyboard –> Soft keys.

§ In the Application –> Counting –> Counting system menu, one scale is configured as Reference scale for determining the average piece weight and the other scale is configured as Bulk scale for counting large numbers of pieces.

1 Place the indicated number of reference parts on the reference scale and press the soft key or .

ð After determining the average piece weight the scale is automatically switched to the bulk scale.

2 Place the empty container on the bulk scale and press

ð The container is tared and the zero display appears.

.

3 Add the parts to the container until the required number of pieces is reached.

Depending on the setting for Total count under Application –> Counting –>

Counting system, the bulk scale will show either the number of pieces on the bulk scale only or the sum of pieces on both reference and bulk scale.

3.10.3 Counting with auxiliary scales

§ At least one of the soft keys Ref N var (

), Ref N fix ( ) or APW ( ) is activated in the menu under Terminal –> Device –> Keyboard –> Soft keys.

§ In the Application –> Counting –> Counting system menu, at least one scale of the system is configured as Auxiliary scale.

§ In the Terminal –> Device –> Keyboard –> Soft keys menu, the soft key Switch scale is activated.

1 Make sure that the selected scale is suitable for the product to be counted.

2 Carry out counting as described in Counting parts into a container [ }  47].

When changing the product to be counted, always check which of the auxiliary scales is the most suitable. If necessary, change the scale.

52 Counting

4 Over/Under Checkweighing and Filling

4.1 Overview

The devices offer Over/Under Checkweighing and Filling functions. The respective settings in the menu are described in the Application menu section.

The correspondingly colored background lighting allows rapid detection of the status “too light” (factory setting: red), “good” (factory setting: green) and “too heavy” (factory setting: yellow). The colors can be modified in the menu.

Over/Under Checkweighing Filling

Tolerance types

Different entries are required at the beginning of Over/Under Checkweighing / Checkcounting / Filling, depending on the tolerance type setting.

Absolute A low and a high weight value must be entered. These weights and all weights within this range are treated as being within tolerance.

Relative

Target weight (Target) as well as lower tolerance (Tol–) and upper tolerance (Tol+) have to be specified. The tolerances are displayed as relative deviations from the target weight.

Percent

Target weight (Target) as well as lower tolerance (Tol–) and upper tolerance (Tol+) have to be specified. At Over/Under Checkweighing / Filling the weight value is represented as a percentage of the target weight. The target weight value is 100 % or 0 % at Over/Under Checkweighing to zero.

Over/Under Checkweighing and Filling 53

4.2 Specifying target values for Over/Under Checkweighing or Filling

The following section describes the course of Over/Under Checkweighing / Filling in the factory setting.

1 Press the soft key for Over/Under Checkweighing or the soft key for Filling.

ð The current Over/Under Checkweighing / Filling parameters are displayed.

2 Check the tolerance type: Press the soft key to change the tolerance type and the cursor key to proceed to the first weight.

ð With a tolerance type selected in the menu, this step does not appear.

3 Load the requested weight or enter the weight value and confirm with the soft key .

ð The next weight is highlighted.

4 Repeat step 3 until New target set is displayed.

ð The colored Over/Under Checkweighing / Filling display appears, the scale is ready for Over/Under

Checkweighing or Filling.

• If tolerance default values have been set in the menu, only the target has to be specified with tolerance types "Relative" and "Percent".

• The upper tolerance value has to be greater than or equal to the lower one (High >= Low) or, respectively, the target weight has to be greater than or equal to the lower tolerance value and smaller than or equal to the upper tolerance (Tol+ >= Target >= Tol–).

4.3 Specifying target number of pieces for Over/Under Checkcounting

§ The soft key Over/Under (

) is activated in the menu under Terminal –> Device –>

Keyboard –> Soft keys (if not shown by default).

§ At least one of the counting soft keys Ref N VAR (

), Ref N FIX ( ) or APW ( ) is activated in the Terminal menu.

1 To determine the average piece weight, apply the indicated number of reference parts as indicated on the soft key or and press the corresponding soft key.

ð The number of reference parts is displayed.

2 To determine the target number of pieces, proceed as described in the previous section.

ð The display unit is PCS.

• For alternate procedures to determine the average piece weight, refer to the Counting section.

• When using the unit PCS, the tolerance type Percent is not available.

• Once the target values are specified, the Over/Under Checkcounting procedures are the same as the Over/Under Checkweighing procedures.

54 Over/Under Checkweighing and Filling

4.4 Over/Under Checkweighing or Checkcounting procedure

The devices facilitate Over/Under Checkweighing and Checkcounting through differently colored background lighting for the status "too light" (factory setting: red), "good" (factory setting: green) and "too heavy" (factory setting: yellow).

1 Specify the target values as described in the previous sections.

Tolerance type "Absolute"

2 Place the Over/Under Checkweighing or Checkcounting material on the scale.

ð Depending on the applied weight, the color of the background lighting changes. Weight information is displayed in accordance with the display setting and the Over/Under Checkweighing settings.

Tolerance type "Relative"

Tolerance type "Percent"

4.5 Filling procedure

The devices facilitate Filling through differently colored background lighting for the status "too light" (factory setting: red), "good" (factory setting: green) and "too heavy" (factory setting: yellow).

1 Specify the target values as described in the previous sections.

Too low

2 Place the empty container on the scale and press

.

ð The container is tared and the zero display appears.

Good

3 Fill in the weighing goods.

ð Depending on the applied weight, the color of the background lighting changes. Weight information is displayed in accordance with the display setting and the Filling settings.

• As long as the weight is below the tolerance, a red bar is displayed.

• When the weight approaches the good range, a second bar is displayed in which the tolerance range is spread. This is an aid to exactly fill in the target weight.

Too high

• When the weight exceeds the tolerance range, the color changes to yellow.

Tol–

LOW

Target Tol+

HI

LOW

Tol–

LOW

Tol–

HI

Tol+

HI

Tol+

Over/Under Checkweighing and Filling 55

4.6 Over/Under Checkweighing / Filling during subtractive weighing (Take away)

Assistance through the colored background and the graphical weighing aid is also possible during subtractive weighing and subtractive counting.

1 Specify target values as described in the previous sections.

ð The target value is indicated with a negative sign.

2 Place a full container on the weighing platform and tare it.

3 Remove as much from the weighing sample as required for the display to change to the status

“good” (factory setting = green).

4 Tare the unit again.

ð The scale is ready for the next removal.

4.7 Over/Under Checkweighing / Filling with "Quick start"

If default values for the tolerances are used with tolerance types "Relative" or "Percent", Over/Under

Checkweighing / Filling can be started by pressing just one key.

§ The setting On is selected in the menu under Application –> Over/Under/Filling –>

Default Values.

§ Tolerance values are defined under Application –> Over/Under/Filling –> Default

Values.

§ The selected tolerance type matches the entered default values.

Place the target weight or target amount on the scale and press the soft key for Over/Under

Checkweighing or for Filling.

ð The applied weight or the applied amount is stored as the target weight or target amount respectively. The display changes to the status "good" (factory setting = green). Over/Under

Checkweighing / Filling is activated.

56 Over/Under Checkweighing and Filling

4.8 Over/Under Checkweighing to zero / Filling to zero

The weight value or the number of pieces can also be represented as the difference to the target weight.

§ For Over/Under Checkweighing to zero / Filling to zero, tolerance types Relative or Percent are selected.

§ For Checkcounting to zero, tolerance type

Relative is selected.

§ Display layout Color mode or 3­line mode is selected in the Terminal menu.

1 Specify the target values as described in the previous sections.

2 Press the soft key .

ð The target is displayed with a minus sign.

3 Place the Over/Under Checkweighing material on the scale.

ð Depending on the applied weight or the applied amount the color of the background lighting changes.

ð The display value is displayed in accordance with the tolerance type setting.

ð The target value is 0 (kg or PCS) or 0.00 %.

Terminating Over/Under Checkweighing to zero / Filling to zero

Press soft key again.

ð The symbol

in the info line disappears, the net weight is displayed.

4.9 Leaving Over/Under Checkweighing / Filling

With clearing the Over/Under Checkweighing / Filling parameters

Press .

ð Cleared appears in the display.

ð The target values are cleared and the straight weighing display appears.

ð The device operates in straight weighing mode.

With keeping the Over/Under checkweighing / Filling parameters

1 Press the soft key .

ð The straight weighing display appears, the Over/Under Checkweighing parameters are kept.

ð The device operates in straight weighing mode.

2 To reactivate the Over/Under Checkweighing / Filling parameters, press the soft key or .

ð The most recently entered Over/Under Checkweighing / Filling parameters are displayed.

Over/Under Checkweighing and Filling 57

58 Classifying

5 Classifying

5.1 Overview

The device offers Classifying functions with up to 12 weight classes. To make operation easier, an individual color is assigned to each weight class. The respective settings in the menu are described in the

Application menu section.

Classifying cannot be combined with other applications like Counting, Over/Under Checkweighing/Filling or

Totalizing.

Class definition

Each weight class is specified by its start value. The end value is automatically set 1 digit below the start value of the next class. Only for the last (highest) weight class an end value has to be specified.

The correspondingly colored background lighting allows rapid detection of the classes. The colors can be modified in the menu.

Class 1 Class 2 Last class

Start value

Class 1

Start value

Class 2

Start value

Class 3

Start value

Last class

End value

5.2 Specifying class definition values

§ The Classifying soft key is activated in the Terminal menu.

1 Press the soft key .

ð A table to specify the class definitions is displayed.

2 Press the soft key and enter the end value.

3 Confirm end value with .

ð The class definition table is displayed.

4 Press the soft key and enter the start value of

Class 1.

5 Confirm start value of Class 1 with .

ð The class definition table is displayed.

6 Repeat steps 4 and 5 until you have entered the start values of all your desired classes.

7 Confirm the class definition with .

ð The classifying display is active.

• If you do not specify the end value, the maximum capacity of the scale is used as end value.

• With Class name set to Custom in the Application menu, you are prompted to enter the class name prior to the value.

• Weighing in class limits is possible as well. Instead of entering the weight value, put the corresponding weight on the platform and confirm with .

5.3 Classifying procedure

§ Class definition values specified as described in the previous section.

Place the classifying material on the scale.

When loading a database record with stored tare weight make sure to always use the same container as specified in the record.

Display for Classifying

With the default color setting and Class name set to Custom the following is displayed:

Lowest class Middle classes Highest class

• The displays shown above are examples:

- The class names are set when specifying the class definition.

- The class colors are set in the menu.

• The arrows indicate that there is a weight class below or above the current class.

• To indicate the class info as shown in the examples, the item Class info must be selected for an auxiliary line, see Application –> Classifying –> Auxiliary lines menu.

• If the weight is outside the range of the defined classes, No class is displayed.

5.4 Classifying during subtractive weighing

Assistance through the colored background is also possible during subtractive weighing.

Procedure

1 Specify class definition values as described in the previous sections.

ð The class definition values must be entered with a negative sign.

2 Place a full container on the weighing platform and tare it.

3 Remove an item and read the result.

4 Tare the unit again.

ð The scale is ready for the next removal.

Classifying 59

5.5 Automatic printout of Classifying results

With Class print set to On in the Application –>

Classifying menu, weighing results within the defined classed are printed out automatically together with the corresponding class information.

5.6 Terminating Classifying

With clearing the Classifying parameters

Press .

ð Cleared appears in the display.

ð The class limits are cleared and the straight weighing display appears.

ð The device operates in straight weighing mode.

With keeping the Classifying parameters

1 Press the soft key .

ð The straight weighing display appears, the class limits parameters are kept.

ð The device operates in straight weighing mode.

2 To reactivate the Classifying parameters, press the soft key .

ð The most recently entered Classifying parameters are displayed.

60 Classifying

6 Totalization

6.1 Starting totalization

Press the soft key .

ð The following soft keys for totalizing are displayed.

Page 1

– –

Page 2

Leave totalizing without clearing the sum

Add item to the sum

Add item to the negative sum

Clear totalization memory

Statistics Define totalizing target

Save totalizing target to the database

Undo totalization

6.2 Totalizing manually

Totalizing

1 Load the first sample and press the soft key .

ð Total Net, Total Gross and number of items are displayed.

ð If configured in the Application menu, the lot print for the first sample is issued.

2 Unload the scale.

3 Load the next sample and press the soft key again.

ð The totals are updated.

ð If configured in the Application menu, the lot print for the next sample is issued.

4 Unload the scale.

5 Repeat steps 3 and 4 for further items.

6 To clear the totalization memory, press the soft key .

ð A safety prompt is displayed.

7 Press the soft key to clear the total.

– or –

Press the soft key to continue totalizing.

• Piece counting results and Over/Under Checkweighing results can be totalized the same way, but they cannot be mixed up in one totalizing action.

• When totalizing Checkweighing/Filling results which are too high or too low, a safety prompt is displayed.

• You can configure the auxiliary lines according to your totalization tasks under Application

–> ... –> Auxiliary lines, e.g. Lot no. or Target.

Totalization 61

62 Totalization

Totalizing in subtractive weighing

1 Load the full container and press

ð The full container is tared.

.

2 Remove the first portion from the container and press the soft key .

ð The removed total is displayed.

ð If configured in the Application menu, the lot print for the first sample is issued.

3 Press .

4 Remove the next portion and press the soft key again.

ð The total is updated.

ð If configured in the Application menu, the lot print for the next sample is issued.

5 Repeat steps 3 and 4 for further portions.

6 Press the soft key to clear the total.

– or –

Press the soft key to continue totalizing.

• Piece counting results and Over/Under Checkweighing results can be totalized the same way, but they cannot be mixed up in one totalizing action.

• When totalizing Checkweighing/Filling results which are too high or too low, a safety prompt is displayed.

• You can configure the auxiliary lines according to your totalization tasks under Application

–> ... –> Auxiliary lines.

6.3 Automatic totalizing

The automatic mode facilitates the totalizing process. After putting the load on the scale, the weight value is added automatically.

§ Auto+ or Auto– is selected under Application –> Totalizing –> Mode.

1 Load the first sample.

ð The total is displayed in the auxiliary lines.

ð If configured in the Application menu, the lot print for the first sample is issued.

2 Unload the scale.

3 Load the next sample.

ð The total is updated.

ð If configured in the Application menu, the lot print for the next sample is issued.

4 Unload the scale.

5 Repeat steps 3 and 4 for further items.

6 To clear the totalization memory, press the soft key .

ð A safety prompt is displayed.

7 Press the soft key to clear the total

– or –

Press the soft key to continue totalizing.

• Piece counting results, Over/Under Checkweighing results, Filling results and Classifying results can be totalized the same way.

• To avoid weighing a sample twice, the Zero return function can be enabled under

Application –> Totalizing. A stable zero must be reached between two samples.

Totalization 63

6.4 Totalizing to a target

The totalizing target can be defined as gross weight, net weight, number of items or number of pieces.

Entering target values

1 Press the soft key .

ð A window opens to specify the target.

2 Select the target type: Gross, Net or Lot (N).

3 Enter the target and confirm with the soft key .

ð The message New target set appears briefly and then the weight display is shown.

Totalizing to a target manually

1 Load the first item and press the soft key .

ð The weight is added to the sum.

ð If configured in the Application menu, the lot print for the first sample is issued.

2 Remove the item from the weighing platform.

3 Load the next item and press the soft key .

ð If configured in the Application menu, the lot print for the next sample is issued.

4 Repeat steps 2 and 3 until Totalization target exceeded is displayed.

5 Confirm the message with the soft key .

6 To clear the totalization memoy, press the soft key .

ð The scale is ready for the next totalizing procedure.

• Target format PCS is available only if the current unit is PCS.

• The totalization target remains stored until a new target is set.

• Checkweighing, Filling or Classifying results can be totalized the same way.

• When in the Application menu Clear at target is set to On, the totalization memory is automatically cleared when the target is reached.

• When in the Application menu Tare after sum is set to On, you can leave the previous weighing good on the load plate.

6.5 Totalizing with leaving the totalized items on the scale

When in the Application menu Tare after sum is set to On, the totalized items can remain on the scale. With this setting it is not necessary to press the tare button after every weighing.

64 Totalization

6.6 Statistical evaluation of the sum

§ For statistical evaluation of the sum, statistics must first be activated.

1 Press the soft key .

ð Activate statistics? is displayed.

2 Press the soft key .

ð From now on all weighings are included in a statistical evaluation.

Displaying statistics

Press the soft key .

ð The statistics of all totalized items since the last clearing of statistics is displayed.

• In the menu under Application –> Statistics you can configure which statistical information will be displayed.

• Statistics can be called up from the Quick Select menu as well.

Printing statistics

Press the soft key .

ð The statistics of all totalized items since the last clearing of statistics is printed or transferred to a computer.

Deleting statistics

1 Press the soft key .

ð A safety prompt is displayed.

2 Press the soft key to delete the statistics.

ð The statistic is cleared.

Deactivating statistics

1 Press the soft key .

ð A safety prompt is displayed.

2 Press the soft key to deactivate statistics.

ð From now on there is no statistical evaluation of the weighings.

Totalization 65

6.7 Terminating totalizing

Terminating totalizing with clearing the total

Press .

ð The total is cleared and the straight weighing display appears.

ð The device operates in straight weighing mode.

Printouts

If configured in the Application menu, the following printouts are printed when clearing the total:

• Final printout with the totals

• Summary printout with the totals and all individual items, see printout example in the Appendix.

Terminating totalizing with keeping the total

Press the soft key .

ð The straight weighing appears, the total is kept.

ð The device operates in straight weighing mode.

To continue totalizing, press the soft key .

ð The last total is displayed.

66 Totalization

7 Settings in the menu

7.1 Menu overview

In the menu, settings can be changed and functions can be activated. This enables adaptation to individual weighing requirements.

The menu consists of the following 5 main blocks containing various submenus on several levels which are described in the following sections.

Scale

Application

Terminal

Communication

Maintenance

7.2 Operating the menu

7.2.1 Calling up the menu and entering the password

The menu differentiates between 2 operating levels: Operator and Supervisor. The Supervisor level can be protected by a password. When the device is delivered, both levels are accessible without a password.

Operator menu

1 Press .

ð The Quick Select menu opens, Menu is highlighted.

2 Press .

ð Enter code is displayed.

3 Press again (no password required).

ð The menu item Terminal is displayed. Only parts of the submenu Device are accessible.

Supervisor menu

1 Press .

ð The Quick Select menu opens, Menu is highlighted.

2 Press .

ð Enter code is displayed.

3 Enter the password.

ð The first menu item Scale is highlighted.

• When the device is first delivered, the supervisor password is set to 000. Set your individual password in the Terminal menu.

• If a password is not entered within a few seconds, the scale returns to the weighing mode.

• If a password has been issued for supervisor access to the menu and you have forgotten it, please contact the METTLER TOLEDO service.

Calling up the menu when user management is active

If user management is active, password entry is required when logging in.

1 Press .

ð The Quick Select menu opens, Menu is highlighted.

2 Press .

ð The menu start screen is displayed, depending on the user profile.

Settings in the menu 67

7.2.2 Display in the menu

Menu tree

The menu tree is displayed like the file system in the Windows Explorer.

For navigating the menu tree use the cursor keys.

/ Navigating up or down the menu tree

>

<

Navigating to a deeper level of the menu tree until the selection window is displayed

Navigating to a higher level of the menu and closing submenus

Selection window

For navigating the selection windows use the following keys:

<

/ Navigating up or down the menu items

Navigating up or down the settings of a menu item

Opening the menu item

Confirming the setting of a menu item

Navigating to a higher level of the menu and closing submenus

Leaving the selection window

Exiting the menu

Press .

ð Save settings? is displayed.

Press the soft key .

ð The menu changes are saved and the terminal returns to the weighing mode.

or

For further menu settings, press the soft key .

or

To discard changes and return to the weighing mode, press the soft key .

68 Settings in the menu

7.2.3 Selecting and setting parameters in the menu

Example: Setting the chain tare function

1 Use cursor key > to enter the Scale menu.

2 Use cursor key > to enter the Scale 1 menu.

ð The first submenu Identification is highlighted.

3 Use cursor key to select (highlight) the Tare menu.

4 Use cursor key > to enter the Tare menu.

ð The selection window is displayed.

The selection window shows the menu items with their current settings.

1 Use cursor key to select Chain tare.

2 Press to open a popup menu with the Chain tare menu.

3 Use cursor keys / > to select the desired setting.

4 Press to confirm the setting.

5 Press the soft key < to leave the selection window and return to the menu tree.

• Menu items in light gray are not available for the current setting or profile.

• Should the settings of a menu not be displayed on one page, (e.g., all the soft keys), use cursor key to proceed to further items.

Settings in the menu 69

7.3 Scale menu block

7.3.1 Scale menu overview

The Scale menu depends on the connected load cell which is indicated on the type label.

Type

ICS685g / ICS689g

ICS685i / ICS689i

ICS685s / ICS689s

ICS685k-.../f

Load cell

Analog

IDNet

SICSpro

MonoBloc

®

Scale menu

Analog scale menu [ }  71]

IDNet scale menu block [

}

 77]

Analog scale menu [

}

 71]

Analog scale menu [

}

 71]

• When entering the Scale menu block, an overview of the connected scales is displayed.

• After selecting a scale, the Scale menu is available.

• If the selected scale is a SICS scale, no further settings are available.

70 Settings in the menu

7.3.2 Scale menu block (Analog / SICSpro)

Overview

Factory settings are printed in bold in the following overview.

Level 1

Identification

Linearization &

Calibration

Disp. unit & res.

Zero

Tare

Restart

Filter

MinWeigh

FACT

(for ICS685k-.../f compact scales only)

Reset

Level 2 Level 3

Serial no. scale, Scale model, Scale location, Scale ID

Level 4

Linearization

Last calibration

3 point, 5 point

On, Off Start up FACT

(for ICS685k-.../f compact scales only)

Auto print calib.

Perform linearization

On, Off

Perform calibration

Display unit 1

Display unit 2 g, kg, oz, lb, lb-oz, t

g, kg, oz, lb, lb-oz, t

Disp. resolution

Unit roll

AZM

On, Off

Auto tare

Chain tare

Auto clear tare

On, Off

Vibration

Process

Stability

MinWeigh

Off, 0.5d, 1d, 2d, 5d, 10d

On, Off

On, Off

On, Off

Low, Medium, High

Universal, Dosing, Absolute

Display color

Temperature

Time

Days

Perform reset?

Fast, Standard, Precise

On, Off

White, Yellow, Red, Green, Blue, Violet, Dark blue,

Grey

Off, 1K, 2K, 3K

Time 1, Time 2, Time 3

Monday ... Sunday Off, On

Description

Identification

Serial no. scale

Scale model

Scale location

Scale ID

Notes

Displaying/setting scale identification data

Displaying the serial number of the weighing platform

Displaying the scale type, e.g., PBD555

Available for METTLER TOLEDO scales only

Entering the scale location, e.g., floor and room

Entering the scale identification, e.g., inventory number

• Scale location and Scale ID can be displayed in the auxiliary or info lines or printed out.

• Scale location and Scale ID can consist of up to 40 alphanumerical characters.

Settings in the menu 71

Linearization & Calibration Linearization and calibration

Linearization

Last calibration

Start up FACT

Select linearization method: 3 point or 5 point

Shows the date of the last calibration.

Autoprint calib.

When set to On, an internal calibration is performed every time the scale is switched on.

It is recommended not to disable this setting if the scale will be moved to other locations.

When set to On, a protocol is printed out automatically for each calibration process.

1 Ensure that the weighing platform is empty.

Perform linearization

2 Press the soft key .

ð Preload is blinking.

3 If applicable, apply preload and confirm with .

ð xx kg is blinking.

4 Apply the displayed weight and confirm with .

ð The next linearization weight is blinking.

5 Repeat step 4 until the Calibration log screen is displayed.

6 Press the soft key to leave linearization.

– or –

ð Press the soft key

to edit the linearization log (entering user name, weight name and comment).

72 Settings in the menu

Linearization & Calibration Linearization and calibration

Important: With ICS685k-.../f weighing terminals make sure that the scale has been switched on at least 15 minutes before performing linearization/calibration.

Perform calibration

1 Unload scale.

2 Press the soft key .

ð Preload is blinking.

3 If applicable, apply preload and confirm with .

ð xx kg is blinking.

ð If necessary, the displayed calibration weight value can be changed using the displayed arrow soft keys.

4 Apply the displayed calibration weight and confirm with .

ð The Calibration log screen is displayed.

5 Press the soft key to leave calibration

6 Press the soft key to leave linearization.

– or –

ð Press the soft key

to edit the linearization log (entering user name, weight name and comment).

Notes • In order to achieve a particularly high precision, calibrate under full load.

• The calibration process can be aborted using .

• This menu item is not available for verified scales.

Settings in the menu 73

Disp. unit & res.

Display unit 1

Display unit 2

Display resolution

Unit roll

Notes

Display units and resolution

Selecting weighing unit 1

Selecting weighing unit 2, different from unit 1

Selecting readability (resolution). The possible settings depend on the connected scale.

When set to Off, only the default resolution of the weighing platform is available.

When set to On, the weight value can be displayed in all available units with .

• In case of verified scales, individual sub-items of the Display/

Units & Resolution menu item may not be available or only to a limited extent, depending on the respective country.

• On dual-range/dual interval scales, resolutions marked with l<–>l 1/2 are divided into 2 weighing ranges/intervals, e.g., 2 x 3000 d.

• On triple-range/multi interval scales, resolutions marked with l<–

>l 1/2/3 are divided into 3 weighing ranges/intervals, e.g.,

3 x 3000 d.

Zero

AZM

Automatic zero setting

Automatic Zero Maintenance

On/Off Switching automatic zero maintenance on/off.

Off; 0.5 d; 1 d; 2 d; 5 d; 10 d Selecting zeroing range in digits per second.

Note On verified scales, this menu item does not appear.

Tare

Auto tare

Chain tare

Auto clear tare

Restart

Restart

Tare function

Switching on/off automatic taring

Auto tare = On: When a load is placed on the scale and the gross weight exceeds 9 d, the weight is tared automatically.

Switching on/off chain tare

Chain tare = On: It is possible to tare several times if, e.g., cardboard is placed between individual layers in a container.

Switching on/off automatic clearing of the tare weight

Auto clear tare = On: When the load is removed and the weight drops below 9 d, the tare weight is cleared automatically.

Automatic saving of zero point and tare value

When set to On, the last zero point and the tare value are saved.

After switching off/on or after a power interruption, the device continues to work with the saved zero point and tare value.

74 Settings in the menu

Filter

Vibration

Low

Medium

High

Process

Universal

Dosing

Absolute

Stability

Fast

Standard

Precise

MinWeigh

MinWeigh

Display color

Note

FACT

Temperature

Off

1K, 2K, 3K

Time

Time 1, Time 2, Time 3

Days

Monday ... Sunday

Note

Filter settings

Adaptation to ambient conditions

Very steady and stable environment. The scale works very rapidly, but is very sensitive to external influences.

Normal environment. The scale operates at medium speed.

Unstable environment. The scale works more slowly, but is less sensitive to external influences.

Adaptation to the weighing process

Universal setting for all weighing samples and normal weighing goods.

Dispensing liquid or powdery weighing samples (only for certain weighing platforms, e.g., PBK9-series / PFK9-series).

For solid bodies under extreme conditions, e.g., strong vibrations.

Adjusting the stability detector

The slower the scale works, the greater the reproducibility of the weighing results.

The scale operates very fast.

The scale operates at medium speed.

The scale operates with the greatest possible reproducibility.

MinWeigh function

Switching MinWeigh function on/off

When set to On and if the weight on the scale drops below the stored minimum weight, will appear in the symbols and info line and the display color will change.

Setting the display color for weight values below the stored minimum weight.

Before you can use this function, the METTLER TOLEDO service technician has to determine and enter a minimum weight value.

Fully automatic calibration test (for ICS685k-.../f compact scales only)

Setting the temperature difference for automatic adjustment.

Switching off automatic adjustment in case of a temperature difference.

Automatic adjustment in case of the selected temperature change.

Setting up to 3 times per day for automatic adjustment.

Entering the times for the automatic adjustment (hours, minutes in 24 h format).

To deactivate Time 2 and Time 3, set them to 00:00:00.

Setting the days of the week for automatic adjustment.

On all days which are set to On, the automatic adjustment will be performed.

FACT is executed under the following conditions:

• No key has been pressed for 3 minutes.

– and –

• The displayed weight value is smaller than 30 d and stable.

Settings in the menu 75

Reset

Perform reset?

Resetting the scale settings to factory settings

Confirm with to reset the scale menu settings.

For ICS685k-.../f compact scales only

1 Press Reset for 5 seconds.

ð Reset User Calibration is displayed.

2 Confirm with to reset the user calibration.

76 Settings in the menu

7.3.3 IDNet scale menu block

Overview

Level 1

Display unit & Resolution

Zero

Tare

Restart

Filter

Update

MinWeigh

Reset

Level 2

Display unit 2

Unit roll

AZM

Auto tare

Auto clear tare

Chain tare

MinWeigh value

Display color

Level 3

g, kg, oz, lb, t

On, Off

Off, 0.5d, 1d, 2d, 5d, 10d

On, Off

On, Off, 9 d

On, Off

On, Off

Vibration

Process

Stability

Stable, Normal, Unstable

Finefill, Universal, Absolute

ASD = 0, 1, 2, 3, 4, 5

The possible settings depend on the connected scale

Function On, Off

White, Yellow, Red, Green, Blue, Violet,

Dark blue, Grey

Perform reset?

Description

Identification

Serial no. scale

Scale model

Scale location

Scale ID

Notes

Displaying/setting scale identification data

Displaying the serial number of the weighing platform

Displaying the scale type, e.g., PBD555

Available for METTLER TOLEDO scales only

Entering the scale location, e.g., floor and room

Entering the scale identification, e.g., inventory number

• Scale location and Scale ID can be displayed in the auxiliary or info lines or printed out.

• Scale location and Scale ID can consist of up to 24 alphanumerical characters.

Display unit & Resolution

Unit 2

Unit roll

Notes

Setting the weighing units

Selecting weighing unit 2, different from unit 1.

When set to On, the weight value can be displayed in all available units with .

• In case of verified scales, individual sub-items of the Display unit & Resolution menu item may not be available or only to a limited extent, depending on the respective country.

• On dual-range/dual interval scales, resolutions marked with l<–>l 1/2 are divided up into 2 weighing ranges/intervals, e.g., 2 x 3000 d.

• On triple-range/multi interval scales, resolutions marked with l<–

>l 1/2/3 are divided up into 3 weighing ranges/intervals, e.g.,

3 x 3000 d.

Settings in the menu 77

Tare

Auto tare

On

Off

Auto clear tare

On

Off

9 d

Chain tare

On

Off

Restart

Restart

Zero

AZM

On/Off

0.5d, 1d, 2d, 5d, 10d

Notes

Automatic zero setting

Automatic Zero Maintenance

Switching automatic zero maintenance on/off.

Selecting the threshold for automatic zero setting.

• On verified scales, this menu item does not appear.

• The effective range of the zero update mode can only be set by the

METTLER TOLEDO service technician.

Tare function

Switching on/off automatic taring.

When a load is placed on the scale and the gross weight exceeds 9 d, the weight is tared automatically.

No automatic taring.

Configuring the automatic clearing of the tare weight.

The tare weight is automatically cleared if the gross weight is 0 or below zero.

No automatic clearing of the tare weight.

The tare weight is automatically cleared if the gross weight is within +/–

 9 display steps.

Switching on/off chain tare.

It is possible to tare several times if, e.g., cardboard is placed between individual layers in a container.

Taring is only possible once.

Automatic saving of zero point and tare value

When set to On, the last zero point and the tare value are saved.

After switching off/on or after a power interruption, the device continues to work with the saved zero point and tare value.

78 Settings in the menu

ASD = 0

ASD = 1

...

ASD = 4

Update

xx UPS

Notes

Filter

Vibration

Low

Medium

High

Process

Dosing

Universal

Absolute

Stability

MinWeigh

MinWeigh

Display color

Note

Reset

Perform reset?

Filter settings

Adaptation to ambient conditions

Very steady and stable environment. The scale works very rapidly, but is very sensitive to external influences.

Normal environment. The scale operates at medium speed.

Unstable environment. The scale works more slowly, but is insensitive to external influences.

Adaptation to the weighing process

Dispensing of liquid or powdered weighing samples manually.

Universal setting for all weighing samples and normal weighing goods.

No adaptation, to perform automated filling processes, e.g., with PLC.

Adjusting the stability detector

The slower the scale works, the greater the reproducibility of the weighing results.

Stability detector switched off. Only possible for non-verified scales.

Rapid display, good reproducibility

...

Slow display, excellent reproducibility

Setting the display speed of the weight display

Selecting the number of updates per second (UPS).

• This menu is only displayed if the Update function is supported by the connected scale.

• The possible settings depend on the connected scale.

MinWeigh function

Switching MinWeigh function on/off

When set to On and if the weight on the scale drops below the stored minimum weight, will appear in the symbols and info line and the display color will change.

Setting the display color for weight values below the stored minimum weight.

Before you can use this function, the METTLER TOLEDO service technician has to determine and enter a minimum weight value.

Resetting the scale settings to factory settings

Confirm resetting with .

Settings in the menu 79

7.4 Application menu block

7.4.1 Application menu overview

The Application menu block consists of the following main subblocks, which are described in detail below.

• Straight weighing

• Average weighing

• Clever print

• Counting

• Over/Under Checkweighing, Filling

• Classifying

• Totalizing

• Identification

• Statistics

• Memory

• Article database

• Prompting

Factory settings are printed in bold in the following overviews.

80 Settings in the menu

7.4.2 Application –> Straight weighing

Overview

Level 1

Auxiliary lines

Level 2

Auxiliary line 1

...

Auxiliary line 3

Printout

Level 3

Not used, Date & time (for battery devices incl. remaining capacity in % and in hours), Gross, Net, Tare, High resolution

(for non-approved scales only), ID1, ID2, ID3, Bargraph,

Temperature (for ICS685k-.../f only), Consecutive number,

Active scale model, Terminal location, APW, Reference count,

Quantity, Custom unit factor, CntAccuracy, Target, Tolerance +,

Tolerance –, Deviation, Article, Article description, Article info 1,

Article info 2, Article info 3, Total net, Total gross, Total PCS,

Total target, Lot, User name, User ID, Class info.

Off, Standard, Template 1 ... Template 20

COM1

...

COM4

Description

Auxiliary lines

Auxiliary line 1

Auxiliary line 2

Auxiliary line 3

Selecting contents of the auxiliary lines in the straight weighing application

Factory setting: Date & Time

Factory setting: Bargraph

Factory setting: Article

Printout

COM1 ... COM4

Off

Standard

Template 1 ... Template 10

Notes

Defining printer and template in the straight weighing application

Selecting the COM port for the desired printer

E.g., COM1 for printout to a PC and the optional COM2 for printout on an office (ASCII) printer

No printout on this COM port

Printout with the standard template on the selected printer

Assigning a customer template to the selected printer

• Templates 1 ... 10 can be defined under Communication –>

Define templates.

• This menu item is only available if a COM port is set to Print mode.

• There are 10 more templates available (Template 10 ... Template 20).

Please ask your METTLER TOLEDO service technician to configure these templates or create them by yourself using the DatabICS software

(www.mt.com/ind-databics), if desired.

Settings in the menu 81

7.4.3 Application –> Average weighing

Mode

Soft key

Auto

Selecting mode for determining the average weight for an unstable load (dynamic weighing)

Calculating average weight with manual start of the weighing cycle via soft key

Calculating average weight with automatic start of the weighing cycle

Timer

Auxiliary lines

Auxiliary line 1

Auxiliary line 2

Auxiliary line 3

Selecting the period of time over which the average weight is calculated

With a longer timer setting the reproducibility of the average weighing result is better

Factory setting: 4 seconds

Possible settings: 0 ... 99 seconds

Selecting mode for determining the average weight for an unstable load (dynamic weighing)

Factory setting: High resolution

Factory setting: Bargraph

Factory setting: Article

Printout Defining printer and template in the average weighing application

See Application –> Straight weighing

7.4.4 Application –> Clever print

Clever print Settings for printing without pressing a key

Activate

Threshold

When set to On, the result is automatically printed when the weight between two weighings has dropped below the threshold.

Enter threshold for unloading the scale between two weighings.

Possible settings: 0.0 kg ... max. capacity

Factory setting: 0.0 kg

82 Settings in the menu

7.4.5 Application –> Counting

Overview

Level 1

Unit & Reference

Average piece / unit weight

Counting system

Auxiliary lines

Printout

Level 2

Unit type

Unit name

Unit format

Reference size

Fixed reference size

Reference weight check

Level 3

Piece counting, Custom unit

Display color < Minimum ref.

weight

APW optimization

Autosampling

Off, On

Off, On, 1 % ... 30 %

Red, Green, Blue, Violet, Dark blue, Grey,

White, Yellow

Off, Auto, soft key

On, Off

Auto clear APW

Counting accuracy

On, Off

%, PCS/Custom unit

Scale 1 ... Scale 4

Total count

Bulk, Reference, Aux., Off

Bulk, Bulk + Ref.

see Application –> Straight weighing

Settings in the menu 83

Description

Unit & Reference

Unit type

Piece counting

Custom unit

Unit name

Monitoring the minimum reference weight

Selecting the unit for counting pieces or measuring, e.g., lengths or volumes

Unit type for counting pieces. The result is an integer number.

Unit type for measuring in a user-defined unit, e.g., lengths, areas or liquid volumes. The result is a decimal number.

Entering a name for the Custom unit with max. 5 characters, e.g,

"Screws", "m", "ml"

Setting the resolution of the counting result with unit type Custom unit Unit format

y.yyy

Reference size

Fixed reference size

Off

On

Reference weight check

Off

On

1 %, 2 %, ... 30 %

Display color < Tolerance ref.

weight

Defining a default reference size, e.g., 12 PCS

The reference size is displayed in the soft key .

Selecting the type of reference size

Variable reference size, i.e., any number of parts can be used as reference size

Determining the average piece weigh is only possible with the default reference size

Monitoring the minimum reference weight

No monitoring of the minimum reference weight

Monitoring the minimum reference weight. When the reference weight drops below the set tolerance value, the display color changes and a message is displayed which asks you to add more reference parts.

Setting the process tolerance for the reference weight check. The higher the process tolerance, the smaller the required minimum reference weight.

Only displayed if Reference weight check is set to On.

Selecting the display color for reference weights below the tolerance value set for the reference weight check

Average piece / unit weight Advanced settings for counting

APW optimization

Off

Auto

Soft key

Autosampling

On

Off

Auto clear APW

On

Off

Optimiziation of the average piece weight

No optimization of the average piece weight

Automatic optimization of the average piece weight

Manual optimization of the average piece weight with soft key

Automatic determination of the average piece weight

After taring, the average piece weight is determined with the next weight placed on the scale and the displayed reference size

No automatic determination of the average piece weight

Automatic clearing of the average piece weight

When the load is taken off the scale after a counting operation, the average piece weight is automatically cleared. The next counting operation will begin with determining the average piece weight again.

The average piece weight must be cleared manually with .

84 Settings in the menu

Average piece / unit weight Advanced settings for counting

Counting accuracy

%

PCS/Custom unit

Selecting the unit for displaying the counting accuracy in an auxiliary line

In addition, the item Counting accuracy must be activated for an auxiliary line under Application –> Counting –>

Auxiliary lines.

In the displayed counting accuracy the standard deviation of the parts is not included.

Display of the counting accuracy in %

Display of the counting accuracy in PCS/Custom unit

Counting system

Scale 1 ... Scale 4

Bulk

Reference

Aux.

Off

Total count

Bulk

Bulk + Ref.

Auxiliary lines

Auxiliary line 1

Auxiliary line 2

Auxiliary line 3

Possible contents of the auxiliary lines

Printout

Configuring a system of several scales for counting

Selecting the scale to assign a function in the counting system.

Only the connected scalesare displayed.

The selected scale serves as bulk scale to count/measure quantities.

Another scale of the system must be set to Reference.

The selected scale serves as reference scale to determine the average piece/unit weight. Another scale of the system must be set to Bulk.

The selected scale can be used for determining the average piece/unit weight as well as for counting/measuring.

The selected scale is not part of a counting system.

Selecting the displayed number of pieces on the bulk scale

Only the pieces on the bulk scale are displayed.

The pieces both on the bulk scale and on the reference scale are displayed on the bulk scale.

Selecting contents of the auxiliary lines in the straight weighing application

Factory setting: High resolution

Factory setting: Bargraph

Factory setting: Article

See Application –> Straight weighing

Defining printer and template in the counting application

See Application –> Straight weighing.

Settings in the menu 85

7.4.6 Application –> Over/Under

Overview

Level 1

Default values

Output

Display mode & Colors

Auxiliary lines

Printout

Level 2

Initial tolerance type

Act. deft. values

Rel. weight

Per. weight

Rel. pieces

Thresh % of Tol–

Level 3

Off, Absolute, Relative, Percent

Off, On

Tol–, Tol+

Tol–, Tol+

Tol–, Tol+

0 ... 12 ... 100 %

Beeper Off, Within Tolerances, Outside

Tolerances, Stable result

Stable result, Tolerance border Beeper mode

Autoprint

Off, Within Tolerances, Outside

Tolerances, Stable result

On, Off Stealth mode

Good range White, Yellow, Red, Green, Blue, Violet,

Dark blue, Grey (not for ICS685)

Under range

Over range

Below threshold

See Application –> Straight weighing

Description

Default values

Initial tolerance type

Act. deft. values

Rel. weight

Per. weight

Rel. pcs

Note

Storing default tolerance values

Selecting default tolerance type

Off: No tolerance type predefined. It can be set individually when entering

Over/Under Checkweighing parameters.

Absolute: A low and a high weight value must be entered. These weights and all weights within this range are treated as being within tolerance.

Relative: The target weight has to be entered as an absolute weight, upper and lower tolerances as deviations in weight from the target weight.

Percent: The target weight has to be entered as an absolute weight, upper and lower tolerances as deviations in percent from the target weight. This setting is not available for counting.

Activating/deactivating usage of default tolerance values.

Entering the default values for Tolerance – and Tolerance +.

Entering the default percentages for Tolerance – and Tolerance +.

Entering the default values for Tolerance – and Tolerance + in pieces or in a defined custom unit.

When always using the same tolerances for Over/Under Checkweighing, store these tolerances to avoid entering tolerances all the time.

86 Settings in the menu

Beeper

Off

Within tolerances

Outside tolerances

Stable result

Beeper mode

Stable result

Tolerance border

Autoprint

Off

Within tolerances

Outside tolerances

Stable result

Note

Output

Threshold as % of Tol–

Setting output options

Threshold to determine at which weight the status of Tol– is indicated.

To avoid Tol– being active at zero or a very low weight, you can define the "Threshold as % of Tol–".

When Threshold as % of Tol– is reached, the colored display will change from the "Below threshold" color to the "Tolerance –" color.

This feature can be used to show the "Tolerance –" color close to the target or as additional setpoint for I/O control.

This setpoint is available on the optional digital I/O interface as well.

Example: Target = 1000 g, Tol– = 100 g

Threshold = x % * (Target – (Tol–))

Threshold = 12 % * (1000 g – 100 g) = 12 % * 900 g = 108 g

In the example, the Tol– color is displayed for weights from 108 g up to

900 g.

Setting the beeper for Over/Under Checkweighing

No beeper

A short beep will sound when a weight value within the tolerance values is reached

A short beep will sound when a weight value outside the tolerance values is reached

A short beep will sound when a stable result is reached

Defining how the beeper will act

Beeping only when a stable weight value within the selected range is recognized

Beeping on every entering or leaving of the good range

Setting the automatic printout

No automatic printout

Automatic printout when a stable weight value within the tolerance values is reached

Automatic printout when a stable weight value outside the tolerance values is reached

Automatic printout when a stable result is reached

For the automatic printout, the communication port at which the printer is connected, must be configured as follows: COMx –> Mode –>

Print  (and not Auto Print!)

Settings in the menu 87

Display mode & colors

Stealth mode

Good range

Under range

Over range

Below threshold

Auxiliary lines

Auxiliary line 1

Auxiliary line 2

Auxiliary line 3

Printout

Setting the weight display in the Over/Under Checkweighing application

This menu item is not available for approved scales.

When set to On, there is no weight display, only the (colored) display for

"too light", "good" and "too heavy".

Selecting the color to indicate a weight value within tolerances

Factory setting: green

Selecting the color to indicate a weight value below "Tolerance –"

Factory setting: red

Selecting the color to indicate a weight value above "Tolerance +"

Factory setting: yellow

Selecting the color to indicate a weight value below "Threshold as % of

Tol–"

Factory setting: white

Selecting contents of the auxiliary lines in the straight weighing application

Factory setting: Not used

Factory setting: Not used

Factory setting: Article

Defining printer and template in the Over/Under Checkweighing application

See Application –> Straight weighing

88 Settings in the menu

7.4.7 Application –> Classifying

Overview

Level 1

Class name

Class print

Display mode

Stealth mode

Color

Auxiliary lines

Printout

Level 2 Level 3

Default, Customized

Off, On

Continuous, Stable

Off, On

Out of class,

Class 1 ... Class 12

White, Yellow, Light blue, Dark blue,

Light red, Dark red, Orange, Violet, Light green, Dark green, Pink, Light grey, Dark grey

See Application –> Straight weighing

Description

Classifying

Class name

Default

Custom

Class print

Off

On

Display mode

Continuous

Stable

Stealth mode

Off

On

Color

Out of class

Class 1 ... Class 12

Setting classifying parameters

Naming of the classes

When entering class identification values, only the weight values have to be entered. The class names are Class 1 to Class 12.

When entering class identification values, the class names can be entered, too.

Printout with class information

No class information on the printout

Printout with class information

Setting the class display

Continuous class display

Class display when a stable weight value is reached

Hiding the weight display

Colored display for the classes with weight value

Only colored display for the classes, without weight value. Not available, if the scale is approved.

Setting the colors for the classes

Factory setting: White

In the factory setting, Class 1 ... Class 12 are displayed in the following order: Yellow, Light blue, Dark blue, Light red, Dark red, Orange, Violet,

Light green, Dark green, Pink, Light grey, Dark grey

Settings in the menu 89

7.4.8 Application –> Totalizing

Overview

Level 1

Mode

Auxiliary lines

Printout

Level 2

Mode

Zero return

Tare after sum

Clear at target

See "Straight weighing"

Lot print

Final print

Summary print

Level 3

Manual, Auto +, Auto –

Off, On

Off, On

Off, On

COM1 ... COM4

Level 4

Off, Standard,

Template 1 ...

Template 20

Description

Mode

Mode

Manual

Auto +

Auto –

Zero return

On

Off

Tare after sum

On

Off

Clear at target

On

Off

Configuring totalizing

Selecting the totalizing mode

Items must be totalized manually with the soft key

Stable weight values will be totalized automatically

Automatic totalization of stable weight values in subtractive weighing

Reaching a stable zero point between two items

The scale must be unloaded before totalization of the next item is possible

No load removal requested between two items

Leaving the totalized items on the scale

The weight is automatically tared after each totalizing process

No automatic taring after totalizing

Clearing of the sum when the target (lot numer) is reached

For this function, at least one communication port must be configured as

"Printer".

Automatic clearing of the sum when the target is reached

The sum has to be cleared manually

Printout

Lot print

Final print

Summary print

COM1 ... COM4

Off

Standard

Template 1 ... Template 10

Defining printer and template in the totalizing application

Printout for each individual totalizing action

Printout of the total at the end of totalizing (by pressing or deleting

the memory)

Additional printout of the individual items

Selecting the printer interface for the selected printout

No automatic printout

Automatic printout using the standard template which is predefined in the factory

Automatic printout using the selected template

90 Settings in the menu

7.4.9 Application –> Identification

ID1, ID2, ID3

Soft key description

Printout description

Labelling the identification soft keys

Entering a soft key label for the identification soft keys with max.

5 characters.

E.g., soft keys "User, "Art.No.", "Lot" instead of ID1, ID2, ID3

Entering a description of the identification for printout with max.

40 characters.

E.g., "User name", "Article number", "Lot number" on the printout instead of ID1, ID2, ID3

7.4.10 Application –> Statistics

Statistics

Standard dev

Std. dev. good

Mean value

Mean value good

Max. value

Min. value

Median

% ratio per class

# per class

Note

Selecting statistical information to be displayed or printed

Standard deviation of a weighing series

Standard deviation of all samples within tolerances of a weighing series

Mean value of a weighing series

Mean value of all samples within tolerances of a weighing series

Maximum weight value of a weighing series

Minimum weight value of a weighing series

Weight value separating the higher half of a weighing series from the lower half

Percentage of good, high and low items in a weighing series

Number of good, high or low items in a weighing series

In the factory setting all items are activated

Settings in the menu 91

7.4.11 Application –> Memory

Overview

Level 1

Memory mode

Memory backup

Level 2

File name

Delimiter

Level 3

Mode

Alibi, Transaction, Off

Field 1 ... Field 12

Off, Date & time, Net, Tare, SNo Scale, Terminal location,

Article, Article description, ID1, ID2, ID34, APW, Quantity, SNo

Terminal, Temperature (for ICS685k-.../f only), Gross, User name, User ID, Unit name, Article Info 1, Article Info 2, Article

Info 3, Reference count, Counting accuracy, n, Weight position

, : ;

Description

Memory mode

Mode

Off

Alibi

Transactiion

Field 1 ... Field 12

Configuring a system of several scales for counting

Configuring memory mode

No memory of weighing results

Alibi memory active.

All transferred weighing results are stored in the terminal. The information required by law is stored in fields 1 to 4. These fields cannot be changed.

Additional information is selectable for the fields 5 to 12.

Transaction memory active.

All transferred weighing results are stored in the terminal. The information to be stored in the fields 1 to 12 is freely selectable.

Selecting information to be stored in the corresponding fields

Memory backup

File name

Delimiter

Note

Download of the complete memory to a USB stick as a .csv file

Enter the file name of the memory backup

Select the delimiter in the memory .csv file

This menu item is only available if a USB Host interface is installed

92 Settings in the menu

7.4.12 Application –> Database

Database access mode

Internal DB

External DB

COM –> COM1 ... COM4

IP address

Port

Specifying database

Internal database, database maintenance via the ICS685 / ICS689 terminal

External database, database maintenance via the DatabICS software

(www.mt.com/ind-databics)

Selecting terminal port of the external database

Entering IP address of the server of the external database

Entering port of the database on the external server

Database backup

File name

Delimiter

Note

Download of the complete database to a USB stick as a .csv file

Enter the file name of the database backup

Select the delimiter in the database .csv file

This menu item is only available if a USB Host interface is installed.

Database restore

File name

Note

Restore/load the database from a USB stick

Select the file name of the database and press .

The database is uploaded to the terminal

This menu item is only available if a USB Host interface is installed.

7.4.13 Application –> Prompting

Overview

Level 1

Prompt 1

...

Prompt 3

Custom prompts

Level 2

Mode

Level 3 Level 4

Disabled, Soft key

Level 5

Soft key description

Apps Off, Tare/Sample, Sample/Tare, Handsfree counting, Multi tare, Additive tare, Take away, Custom prompt 1 ... Custom prompt 3

Custom prompt 1

...

Custom prompt 3

Name

Step 1

...

Step 15

Prompt text

Prompt function

Text, Tare, Clear tare, Auto tare, Preset tare, Print, Auto print, Auto switch scale

1 ... 4, Reference, Auto reference, APW,

Auto APW clear, ID1, ID2, ID3, Recall article

Settings in the menu 93

Apps

Tare/Sample

Sample/Tare

Handsfree

Multi tare

Additive tare

Take away

Custom prompt 1

...

Custom prompt 3

Custom prompts

Custom prompt 1

...

Custom prompt 3

Name

Step 1 ... Step 15

• Prompt text

• Prompt function

Note

Description

Prompt 1 ... Prompt 3

Mode

Disabled

Soft key

Soft key description

Configuring user guidance

Configuring start of the prompting

No prompting

Start by a soft key

Entering a description for the prompting soft key with max. 5 characters

E.g., "Count", "Check", Class" when there are specific user guidances for these applications.

This menu item is only available if Soft key is activated.

Selecting the workflow which shall be supported by the prompt

Reference determination: First tare, then add reference parts

Reference determination: First weigh reference parts, then tare

Counting without a keystroke

Taring of several containers with the same tare weight

Adding the known tare weight of different containers

Over/Under Checkweighing out of a container without pressing a key

Selecting from custom workflows

Configuring your own workflows with up to 15 steps

Selecting the number of the custom prompt (workflow)

Entering the name of your custom prompt (workflow), max. 24 characters

Selecting the step in the workflow

Entering the text to be displayed with the selected step, max. 30 characters

Selecting function for the step

Before you can start the prompt via soft key you have to assign the prompt to a specific soft key in the Terminal menu under Device

–> Keyboard –> Soft keys

94 Settings in the menu

Example: creating a new prompt for counting parts in a full container

Step Text

1

Put 10 samples on the scale and press key

Function

Reference

Displayed soft key

Note

Confirm action with the indicated soft key

2

Place the full container on the scale

3

Enter tare weight

Text

Preset tare

4

Read the result

5

Print

Text

Print

Confirm action with the indicated soft key

Press the indicated soft key and enter tare weight

Confirm with the indicated soft key

Confirm with the indicated soft key

7.4.14 Application –> Reset

Reset

Perform reset?

Resetting the application settings to factory settings

Confirm resetting with .

Settings in the menu 95

7.5 Terminal menu block

7.5.1 Terminal menu overview

The Terminal menu block consists of the following main subblocks, which are described in detail in the following.

• Device

• Access

• User management

• Reset

Factory settings are printed in bold in the following overview.

7.5.2 Terminal –> Device

Overview

Level 1

Region

Level 2 Level 3 Level 4 Level 5

Language English, US-english, Deutsch, Français, Italiano, Español, Chinese, ...

Date format MM/DD/YY, MM/DD/YYYY, MMM/DD/YYYY, DD/MM/YY, DD/MMM/YYYY, YY/

MM/DD, YYYY/MMM/DD, YYYY/MM/DD, DD/MM/YYYY

Set date Set year

Set month

Set day

Time format 24:MM, 12:MM tt, 24:MM:SS, 12:MM:SS tt

Set time Set hour

Set minutes

Daylight saving

0, 1

Energy save Backlight

On, 5 seconds, 10 seconds, 15 seconds, 30 seconds

Identification

Power off Off, 1 minute, 3 minutes, 5 minutes, 15 minutes, 30 minutes

Terminal location

Terminal ID

Display Display layout

Default, 3-lines mode, Color mode

Contrast 1 ... 5 ... 10

Brightness 1 ... 10

Weight hold 0 s ... 10 s

Default color

White, Yellow, Red, Green, Blue, Violet, Dark blue, Grey

96 Settings in the menu

Level 1 Level 2 Level 3

Keyboard Hard keys Power,

Clear,

Switch, Info,

Transfer,

Numeric keys,

Navigation,

Quick select, Info

Soft key Soft key 1-1

...

Soft key 4-5

Message time

Battery

Level 4

On, Off

Full, Preservation

Level 5

Info key Page 1

Not used, Zero, Tare, Alibi memory, Switch scale, x10 display,

Transfer, Average weighing, ID1, ID2, ID3, Prompt 1, Prompt 2,

Prompt 3, Reference N VAR, Reference N FIX, APW, APW optimization, Totalizing, Checkweighing, Filling, Weight/Count,

Save as article, Temperature check (for ICS685k-.../f only),

Database, Recall article, Logout, Display layout, Consecutive

No., Classifying

Item 1

...

Item 9

Not used, Date & Time, Highres and net, Gross,

Tare, Temperature (for ICS685k-.../f only),

Terminal ID, Terminal location, Terminal model,

SNo. Terminal, Terminal FW, SNo. Scale, Scale

FW, Record number, ID1, ID2, ID3, APW,

Quantity, Total gross, Total net, Total PCS, Lot,

Deviation, Target, Tolerance–, Tolerance+,

MinWeigh, Article, Article description, Article info 1, Article info 2, Article info 3, User name,

User ID, IP address, Subnet mask, Gateway, USB version, Consecutive No., Class no.

Beeper

Page 2 & 3 Info page 2 Off, System info, Contact info

Info page 3 Off, System info, Contact info

On, Off

External keyboard

1 s, 2 s, ... 6 s

Timeout

Charge strategy

Mode

Password

Off, Rental, Rental info

Set date

Rental image

Text 1, Text 2

Set year, Set month, Set day

Default, Customer, Text only

Settings in the menu 97

Description

Region

Language

Date format

Set date

Set month

Set day

Time format

Set time

Set hour

Set minutes

Daylight saving

0

+1

Country specific settings

Selecting the language of the operator interface.

We will expand the available languages continuously.

Selecting the date format.

Entering the date in the selected format.

Entering the month in the selected format.

Entering the day in the selected format.

Selecting the time format.

Entering the time in the selected format.

Entering the hour in the selected format.

Entering the minutes.

Setting daylight saving time

Deactivating daylight saving time

Activating daylight saving time

Energy save (Operator access)

Backlight

On

5 seconds ... 30 seconds

Power off

Off

1 minute ... 30 minutes

Setting the energy saving mode

Settings for switching off the backlighting

Backlight always on

Selecting the time period after which the device switches off display and backlighting when not in use and gross weight is 0. Display and backlighting are switched on again by pressing a key or if the weight changes.

Settings for switching off the device

No energy saving mode

Selecting the time period after which the device switches off when not in use and gross weight is 0. After this, it must be switched on again using

.

Identification

Terminal location

Terminal ID

Notes

Setting terminal identification data

Entering the terminal location, e.g., floor and room

Entering the terminal identification, e.g., inventory number

• Terminal location and terminal identification can be displayed in the auxiliary or info lines or printed out.

• Terminal location and terminal identification can consist of up to

12 characters (0 ... 9 and decimal point).

98 Settings in the menu

Display

Display Layout

Setting the display according to your specific task

Selecting the presentation of the weight value.

Contrast (Operator access) Setting the contrast of the display.

This menu item is accessible with Operator access rights.

Brightness (Operator access) Setting the brightness of the display.

This menu item is accessible with Operator access rights.

Weight hold

Default color

Setting how long (in seconds) the weighing result is frozen in the display after the transfer key has been pressed or auto print was generated.

Setting the default color of the display background.

Keyboard

Hard keys

Soft keys

Soft key 1-1

...

Soft key 4-5

Info key

Page 1

Page 2, Page 3

Beeper

External keyboard

Setting the keyboard according to your specific task

Locking/unlocking keys

Possible keys: Power ( ), Clear ( ), Switch / Toggle ( ),

Info ( ), Transfer ( ), Numeric keys, Navigation, Quick Select ( )

Note: The Quick Select key can be protected by a password.

Assigning a function to the selected key

1 Select the soft key number.

2 Assign function.

Note: If Recall article is selected as function, an additional window opens to enter the corresponding soft key description (max.

4 characters) and to select the article from the database.

Configuring the items to be displayed using the info key ( )

On the first page of the info key up to 9 information items on the weighing process can be configured.

1 Select item number.

2 Assign information.

On pages 2 and 3 system and contact information will be displayed. In case of a problem, here you will find your contact data and the system information the service technician will ask for. System information is set by the manufacturer, contact information can be entered directly.

When set to On, each keystroke will be confirmed by a short beep.

Selecting the layout of an external keyboard which is connected via

USB interface

This menu item is only available if an external keyboard is connected. We will expand the available keyboards continuously.

Message time

1, 2, 3, 4, 5, 6

Battery

Charge strategy

Full

Preservation

Setting how long a message is displayed

Setting how long a message is displayed in seconds

Battery settings

Setting the charging strategy.

The battery will always be fully charged.

Charging to prevent total discharge.

Settings in the menu 99

Time out

Mode

Off

Rental

Rental info

Set date

Set year

Set month

Set day

Setting the behaviour when no action takes place on the terminal

Setting the time out mode.

No time out setting.

The scale can only be used until a set date, e.g., when the scale is rented for a special event like a fair or a market. After the expiration date a message is displayed: Rental expired and the scale can no longer be used.

When the set date has passed, a message is displayed: Rental expired.

By pressing the key , the message is cleared and the scale can be used as before.

Entering the expiration date.

Entering the year of the expiration date.

Entering the month of the expiration date.

Entering the day of the expiration date.

7.5.3 Terminal –> Access

Supervisor

Password

Retype password

Note

Password for Supervisor menu access

Enter password for Supervisor menu access.

Repeat the password entry.

The password can consist of up to 4 characters.

7.5.4 Terminal –> User management

Overview

Level 1

User 1

...

User 20

Level 2

Profile – User x

Hard keys –

User x

Soft keys –

User x

Level 3

User name

User ID

Level 4

Profile

Language

Operator, supervisor

English, Deutsch, Français, Italiano, Español,

Chinese, ...

Password

Activate user On, Off

Power, Clear,

Switch, transfer, Tare,

Numeric keys,

Navigation,

Quick Select,

Info, Zero

Soft key 1-1

...

Soft key 4-5

On, Off

Not used, Zero, Tare, Alibi memory, Switch scale, x10 display, Transfer, Average weighing, ID1, ID2, ID3,

Prompt 1, Prompt 2, Prompt 3, Reference N VAR,

Reference N FIX, APW, APW optimization, Totalizing,

Checkweighing, Filling, Weight/Count, Save as article,

Temperature check (for ICS685k-.../f only), Database,

Recall article, Logout, Display layout, Consecutive no.

100 Settings in the menu

Description

When opening the User management menu block, the following overview is displayed:

1 Use the cursor keys / to select a user.

2 Use the soft key to edit the selected user.

ð The user profile is displayed in detail.

3 Use the soft keys / to proceed to the pages

"Hard keys – User x" and "Soft keys – User x"

User 1 ... User 20

Profile user

User name

User ID

Profile

Language

Password

Activate user

Hard keys user

Soft keys user

Soft key 1-1

...

Soft key 4-5

7.5.5 Terminal –> Reset

Reset

Perform reset?

Configuring up to 20 users

Configuring user profiles

Enter User name, max. 10 characters

Enter a User ID, e.g., personnel number, max. 4 characters

Assigning access rights: Operator, Supervisor

Assigning the individual user language

Setting a password and confirming password

When set to On, the selected user can log on to the device

User-specific locking/unlocking of keys

Possible keys: Power ( ), Clear ( ), Switch ( ), Transfer ( ), Tare

( ), Numeric keys, Navigation, Quick Select (

D U M M Y

), Info ( ), Zero

( )

Setting the user-specific soft key functions

1 Select soft key number.

2 Assign function.

The corresponding soft key symbols are shown in the Introduction chapter.

Resetting the terminal settings to factory settings

Confirm resetting with .

Settings in the menu 101

7.6 Communication menu block

7.6.1 General

For detailed information on interface protocols and commands refer to the SICS Reference manual.

The Communication menu block consists of the following subblocks:

• Overview

• COM1

Showing the interfaces installed.

Parameter settings for the standard RS232 interface COM1.

• COM2 Parameter settings for the optional second interface COM2.

• COM3 / COM4 Parameter settings for the optional interfaces COM3 / COM4.

• Define templates Defining templates to be assigned to the application-specific printouts.

The interfaces identify themselves. Therefore only those menu settings appear which are relevant for the individual interface. If no optional interface is installed, the COM3 / COM4 menu will not appear.

Interface overview

The following is displayed when calling up Communication –> Overview:

102 Settings in the menu

7.6.2 Overview of the communication menu blocks

Possible settings

Mode

Printer

External input

Parameter

TCP settings

Wireless settings

Print

Auto print

Instant print

Continuous

(Dialog)*

Dialog*

External input

Toledo cont.-weight

Toledo cont.-count

SICS scale

X scale

Digitol B

Digitol G

Second display

SICSpro scale

ARM100

COM1 /

COM2

(default)

RS232 RS232 RS422 /

RS485

x x

COM2 (optional / COM3 / COM4

x

Ethernet

(COM3 only)

x

WLAN

(COM3 only)

x

USB

Device

x x x

– x x

– x x x

– x x x x x x x

Factory setting x x x

9600 9600 9600 x x x

– x x

– x x x

– x x

– x x

Baud

(factory setting)

Parity

(factory setting)

Handshake

Checksum**

STX**

RS Type

Net Address

Load resistor

DHCP

IP address

Subnet mask

Gateway

8 none x x x

8 none x x x

8 none x x x x

– x x

– x

– x x

– x

– x

– x

* for more information see SICS Reference manual

** only available for Toledo cont. modes

– x

– x x

USB

Host

– x

– x

Settings in the menu 103

RS232 menu block

Level 1

Mode

Printer

External input

Parameter

Reset RS232

Level 2

ASCII Format

Level 3

Print, Auto print, Instant print, Dialog, Continuous (Dialog), External input,

Toledo Cont.-weight, Toledo Cont.-count, Second display, SICS scale, X scale

Digitol B, Digitol G Net

Gross

Tare

On, Off

Type

ASCII printer, Values only

Line format

Line length

Level 4

Multiple, Single, Fixed

1 ... 24 ... 100

Separator

(for line format Single only)

Add line feed

. , : ; – _ / \ Space

0 ... 9

Preamble length

Data length

Postamble length

Termination character

Destination

Baud

Parity

Handshake

Checksum

Perform Reset?

CR, LF, EOT, ...

Off, Tare preset, ID1, ID2, ID3, APW, Article, Target

300, 600, ... 9600, ... 115200 baud

7 none, 8 none, 7 odd, 8 odd, 7 even, 8 even

Off, Xon – Xoff

Off, On

RS422 / RS485 menu block

Level 1

Mode

Level 2 Level 3

Print, Auto print, Instant print, Dialog, Continuous (Dialog), External input,

Toledo Cont.-weight, Toledo Cont.-count, Second display, SICS scale, X scale,

SICSpro scale, ARM100 see RS232 Printer

External input

Parameter

Reset RS4xx

Baud

Parity

Handshake

RS-Type

Net address

Checksum

Load resistor

Perform Reset ?

300, 600, ... 9600, ... 115200 baud

7 none, 8 none, 7 odd, 8 odd, 7 even, 8 even

Off, Xon – Xoff

RS422, RS485

0 ... 31

Off, On

Off, On

104 Settings in the menu

Ethernet menu block

Level 1

Mode

Printer

External input

Parameter

TCP Mode

Reset Ethernet

Level 2

see RS232

DHCP

Local IP

Subnet mask

Gateway

Checksum

TCP Mode

Local Port

Remote IP

Remote port

Connect timeout

Disconnect timeout

Perform Reset?

Level 3

Off, On

Off, On

Server, Client, FreeWeigh

4305

WLAN menu block

Level 1

Mode

Printer

External input

Parameter

TCP mode

Wireless setting

Level 2

see RS232 see Ethernet see Ethernet

SSID

Encryption

WEP settings

WEP key

WPA settings

Password

Level 3

Display the current status, e.g., connection status, signal strength

Perform Reset?

Off, WEP, WPA

64 Bit, 128 Bit

Key 1, Key 2, Key 3, Key 4

WPA-TKIP, WPA2-AES

Status

Reset WLAN

A license file (RADIUS file) can be implemented via the DatabICS software (mt.com/ind-databics).

Settings in the menu 105

USB Host menu block

Level 1

USB version

Keyboard /

Barcode Reader

USB settings

Level 2

Preamble length

Data length

Postamble length

Termination char.

Destination

Alibi on the fly

Level 3

On, Off

USB Device menu block

Level 1

Mode

Printer

Parameter

Reset USB

Level 2

Checksum

Perform Reset?

Level 3 Level 4

Continuous (Dialog), Dialog, External input, Toledo Cont.-weight, Toledo

Cont.-count, Print, Auto print, Instant print

Digitol B, Digitol G Net, Gross, Tare

On, Off see RS232

Off, On

The driver for USB Device is available on the CD delivered with the weighing terminal.

106 Settings in the menu

7.6.3 Description of the communication menu blocks

Mode

Print

Auto print

Instant print

Dialog

Continuous (Dialog)

External input

Toledo Cont.-weight

Toledo Cont.-count

Second display

SICSpro scale

SICS scale

X scale

Digitol B

Digitol G

Net, Gross, Tare

ARM100

Notes

Operating mode of the serial interface

Manual data output to the printer with

Automatic output of stable results to the printer (e.g., for series weighing operations)

Manual data output of the current weight value (either stable or not) to the printer with

Bi-directional communication via MT-SICS commands, control of the device via PC

Ongoing output of all weight values via the interface

Input other than via terminal keypad. What the input is used for is defined in the Destination menu block.

TOLEDO Continuous mode

TOLEDO Continuous mode with counting results

On the selected interface port, a second display is connected.

On the selected interface port, a SICSpro scale is connected.

On the selected interface port, a SICS scale is connected.

On the selected interface port, an X scale is connected.

Digitol compatible format. The gross weight is identified by "B".

Digitol compatible format. The gross weight is identified by "G".

Selecting the weight values to be transferred.

On the selected interface port an ARM100 input/output module is connected.

Printing conditions for Auto print:

• The weight must be heavier than 9 display increments.

• A weight change of at least 9 display increments is required to initiate the next printout.

Settings in the menu 107

Printer

Type

Configuring printer and formats for the protocol printout

ASCII printer If Values only is selected, the transmitted data does not include the

Values only name of the variable, e.g., date, gross, ID1, but the value and, if appropriate, the unit, as a separate line. This allows the label printer to fill its template with the required data.

ASCII format Line format

Selecting line format (for ASCII printers only)

Multiple

Single

Fixed

Multiple lines

Single lines

Fixed (records output in single lines; every record includes the number of characters that was defined under Line length)

Line length

Setting line length

This item is only displayed for the line formats Multiple and

Fixed.

Separator

Selecting the separator

This item is only displayed for the line format Single.

Add line feed Adding line feeds

External input

Preamble length

Data length

Postamble length

Termination char.

Destination

Configuring input via barcode reader

The barcode may contain additional data before the relevant data

(preamble) and behind (postamble).

Enter the number of characters of preamble, (relevant) data and postamble.

Selecting the termination character which is used by the connected barcode scanner

Selecting the item to be entered via barcode scanner

USB Host

USB version

Destination

USB settings

Configuring the USB Host interface

Show the implemented USB version

Keyboard / Barcode reader Configure the external input via keyboard or barcode

Preamble length The barcode may contain additional data before the relevant data

(preamble) and behind (postamble).

Data length

Postamble length

Enter the number of characters of preamble, (relevant) data and postamble.

Termination char.

Selecting the termination character which is used by the connected barcode scanner

Selecting the item to be entered via barcode scanner

Alibi on the fly

Configuring an external alibi memory

When set to On and a USB stick is inserted, the records are stored on the USB stick as well.

108 Settings in the menu

F2

F3

F4

F5

Connecting an USB keyboard

• To connect an external keyboard via USB Host, the COM port has to be defined as External input with the termination character LF.

• If a function is assigned to the external input as well, e.g., "Load article", use the Enter key to confirm the external input.

The function keys of the USB keyboard correspond to the following keys on the weighing terminal:

F1 F8 Displayed soft key 4

F6

F7

Displayed soft key 1 (left)

Displayed soft key 2

Displayed soft key 3

F9

ESC

Displayed soft key 5 (right)

in the menu

Back Delete text character by character

Enter In straight weighing: print

As external input: confirm

Cursor keys Cursor keys

Parameter

Baud

Parity

Handshake

Checksum

STX

RS Type

Net Address

Load resistor

DHCP

Local IP

Subnet mask

Gateway

Note

Communication parameters

Selecting baud rate

Selecting parity

Selecting handshake

Activating/deactivating checksum byte

Activating/deactivating STX

If STX is set to On, the STX signal (0x02) is sent at the beginning of each output string that is sent via the interface.

Selecting type of the optional RS422/RS485 interface: either RS422 or

RS485

Assigning network address

To avoid reflections on a network, we recommend to make a defined termination. For this purpose, the load resistor within the terminal can be used. When set to On, a resistor of approx. 100 Ohm between the signal lines is enabled.

If DHCP is set to On, the device will receive the IP address automatically.

Then IP address, Subnet mask and Gateway are read-only fields.

Displaying/entering the local IP address

Displaying/entering subnet mask

Displaying/entering gateway address

Not all parameters are available on all serial interfaces. Refer to the overviews of the interfaces to check which parameters are avilable.

Settings in the menu 109

TCP Mode

TCP Mode

Server

Client

FreeWeigh

Local Port

Remote IP

Remote Port

Connect timeout

Disconnect timeout

Transmission control protocol settings

Configuring TCP mode

Weighing terminal acting as server

E.g., to execute SICS commands from a PC. To do so, the weighing terminal must be configured as Server and the PC must be configured as

Client.

Weighing terminal acting as client

E.g., to print to a PC or printer. To do so, the weighing terminal must be configured as Client and the PC must be configured as Server.

To connect as SICS scale to freeweigh.net

Displaying/entering the local port

Displaying/entering the remote IP address

Displaying/entering the remote port

Setting timeout for connecting

Setting timeout for disconnecting

110 Settings in the menu

7.6.4 Digital I/Os menu block

Level 1

Input

Level 2

Input pin 1 ... Input pin 4

Level 3

Off, Zero, Tare, Transfer, Switch, Clear,

Info, Target, Softkey 1-1 ... 4-5, Total +,

Total –, Switch scale

Off, Output pin 1 ... Output pin 4

Output

Setpoints

Output mode

Ready, Stable, Tare, Zero,

< Min weigh, >= Min weigh,

Underload, Overload, Star,

<= Setpoint 1, > Setpoint 1,

<= Setpoint 2, > Setpoint 2,

SP.Tolerance–,

< Tolerance–, Good range,

Target, > Tolerance+,

Class 1 ... Class 12,

End value, Out of class,

< Tot. Lot N, = Tot. Lot N,

< Threshold as % of Tol–

Setpoint 1, Setpoint 2

Continuous, Stable

Configuring inputs

1 Select an input pin.

2 Assign an input signal to the selected input pin.

Configuring outputs

1 Select an output signal.

2 Assign an output pin.

Configuring setpoints

Enter values for the setpoints.

Setting output mode

Continuous

Stable

Digital outputs are updated continuously

Digital outputs are updated only when the weight is stable

Settings in the menu 111

7.6.5 Define templates menu block

Level 1

Template 1

...

Template 10

Level 2

Line 1

...

Line 30

Level 3

Not used, Header *, Date, Time, Gross, Net, Tare, High resolution, ID1, ID2, ID3, Terminal ID, Terminl location, SNo

Terminal, SNo Scale, Star line, New line, Form feed, Target,

Tolerance –, Tolerance +, Tolerance type, Deviation, Weight position, APW, Reference count, Quantity, Article, Article description, Article info 1, Article info 2, Article info 3, Record number, Lot, User name, User ID, Consecutive number

* The content of these items has to be entered via SICS command.

Configuring templates

1 Select a template.

2 Select a line.

3 Assign an item.

There are 10 more templates available (Template 11 ... Template 20). Please ask your METTLER

TOLEDO service technician to configure these templates or create them by yourself using the

DatabICS software (www.mt.com/ind-databics), if desired.

112 Settings in the menu

7.7 Maintenance menu block

7.7.1 Overview

Level 1

Scale test

Keyboard test

Display test

Tool communication

Level 2

Scale 1

...

Scale 4

Level 3

Routine test

Corner load test

Perform test?

Perform test?

Port

Baudrate

Start

Mode

Temperature

Perform reset?

Off, On

Maximum, Minimum

Level 4

Days

External test weight

Weight name

Tolerance

Days

External test weight

Weight name

Tolerance

Print menu settings

Temperature check

Reset all

7.7.2 Description

Scale test

Routine test

Cornerload test

Days

Test weight

Tolerance

Weight name

Testing the selected scale

Configuring routine test or cornerload test

Enter test interval.

0 days means no test functionality.

Enter the test weight value

Enter the tolerance value

Enter the test weight name

Start routine test with internal/external test weight. For details refer to the

Quick Select section.

Start cornerload test. For details refer to the Quick Select section.

Delete routine test / cornerload test log file

Settings in the menu 113

Keyboard test

Perform test?

Display test

Perform test?

Note

Print menu settings

Print menu settings

Temperature check

Mode

Temperature

Tool communication

Port

Baudrate

Start

Reset all

Perform reset?

Testing the keyboard

1 Press to start the keyboard test.

2 Press the keys in the displayed order.

ð If the key works, the device switches to the next key.

ð The keyboard test is terminated by pressing .

Testing the display

1 Press to start the display test.

ð A checkerboard pattern is displayed.

2 Press any key to invert the checkerboard pattern.

3 Press any key to show the colored display.

4 Repeat pressing a key until Completed is displayed.

5 Press to leave the display test.

The display is working properly if all fields are displayed without missing pixels.

Printout of a list of all menu settings

Press .

ð The menu settings are printed out.

Checking the load cell temperature

Activating/deactivating the temperature check

Setting the admissible maximum and minimum temperature

Testing the communication

Selecting the COM port to be tested

Setting the baudrate for testing

Starting tool communication test

Reset all settings to factory setting

Reset all settings to factory settings with .

114 Settings in the menu

8 Quick Select menu

8.1 Quick Select menu overview

The Quick Select menu offers access to logout, routine test and several log files, depending on your configuration.

Press .

ð The Quick Select menu is displayed.

ð The example shows the Quick Select menu with most of the configuration items.

8.2 Entering main menu

In weighing mode press and then .

ð When working with user management, the menu tree is displayed without password entry.

ð When working without user management, password entry is required first.

8.3 Logout

Prerequisite

User management is activated under Terminal –> User Management.

• Logout is described in the Operation chapter.

• Always log out when leaving the terminal in order to prevent unauthorized persons from working on it.

Quick Select menu 115

8.4 Database

8.4.1 Internal versus external database

ICS685 / ICS689 offer an internal database for up to 5,000 articles.

Handling of the internal database is described below.

To administer the database externally, the optional computer program DatabICS is available (www.mt.com/ ind-databics).

DatabICS features

• Administration of article data

• Export/import of databases via .csv file

• Export of the Alibi/Transaction memory via .csv file

• Up to 25 devices can be connected at the same time via Ethernet and/or WLAN

DatabICS use cases

One central database for several scales

Managing several databases on a PC

• Menu setting: Database access mode = External DB

• DatabICS acts as host

• The article to work with has to be downloaded from the host to the device

• The article information cannot be changed on the device

• Each device is working with its own internal database

• The internal databases can be backuped and restored via DatabICS

116 Quick Select menu

8.4.2 (Internal) Database overview

When calling up the database in the Quick Select menu, the following overview is displayed:

• To scroll through the database table use the cursor keys.

• To switch soft key pages use the / soft keys.

The following soft keys are available for editing the database:

Page 1

Page 2

Leave the database, cancel editing

New record Edit the selected article

Load the selected article

Show next soft key page

Page 3

– Delete article Copy article Show previous soft key page

Show next soft key page

– Search for an article

Print article Show previous soft key page

Quick Select menu 117

8.4.3 Creating a new article

The database is organized in the following 6 pages:

Page 1/6: Article info

Page 2/6: Tare

Page 3/6: Counting

Page 4/6: Checkweighing

Page 5/6: Classifying

Page 6/6: Totalizing

• Use the and to scroll through the pages of an article.

• To store application specific data, the corresponding page must be activated.

• When Counting or Totalizing is activated, an additional page is displayed.

1 Press soft key to create a new data record.

ð Page 1/7 – Article is displayed.

2 Enter article name and additional article information, if appropriate

3 Press the soft key to proceed to the next page.

4 Enter the corresponding information, if appropriate.

1 To enter application data (Counting, Checkweighing/

Filling, Classifying), set the right upper field

Activate to On.

ð When Save article to database? is displayed, the data record is complete.

2 Save the article to the database with the soft key .

ð Record stored is displayed briefly and the article overview is displayed.

118 Quick Select menu

8.4.4 Editing an existing article / copying an article

Viewing article

To view the complete database record, use the cursor keys < or >.

Calling up article

Existing article

Copy article

1 Use the cursor keys / .

2 Press the soft key to open the selected article.

1 Use the cursor keys / .

2 Press the soft key to copy the selected article.

3 Edit the copied article.

Editing the article

1 Enter the article data. Confirm each entry with the soft key and use the cursor key to proceed to the next field.

2 Press the soft key to proceed to the next page.

3 Repeat steps 1 and 2 for the next pages.

4 To enter application data (Counting, Checkweighing,

Filling, Classifying, Totalizing), set the right upper field

Activate to On.

ð When Save article to database? is displayed, the data record is complete.

5 Save the article to the database with the soft key .

ð Record stored is displayed briefly and the article overview is displayed.

Quick Select menu 119

8.4.5 Searching and loading an article

Viewing article

For searching an article, the device offers 3 search fields with individual search criterions.

Search fields

• Article

• Article description

• Article info 1 ... Article info 3

• Tare value

Criterions

• == (equal)

• < (smaller)

• <= (smaller or equal)

• > (bigger)

• >= (bigger or equal)

• != (unequal)

1 In the article overview press the soft key .

ð the following search window opens.

2 Select item for Search field 1.

3 Use cursor key to proceed to the corresponding

Data field.

4 Select the search criterion in the Data field.

5 Use cursor key to proceed to the field for entering the search data.

6 Enter search data, e.g., an article name.

7 Repeat steps 2 to 6 for Search field 2 and Search

field 3, if desired.

8 Start the search with the soft key .

ð The database table with the matching article(s) is displayed.

9 If applicable, use the cursor keys or to select the article.

10 Load the article with the soft key .

ð Record loaded is displayed briefly.

ð Those applications are active which were set to On in the Activate field.

8.4.6 Deleting an article

1 Select the article to be deleted as described in the previous section.

2 Switch to soft key page 2.

3 Press the soft key to delete the selected article.

ð A safety prompt is displayed.

4 Press the soft key to delete the article.

8.4.7 Database download/upload

To download/upload the database from/to an USB stick refer to the menu Application –> Database

[ }  93].

120 Quick Select menu

8.5 Calling up memory log file

Calling up a memory log file is described in the Operation section.

8.6 Statistics

Statistics is described in the Totalizing section.

8.7 Performing routine test

By performing a routine test you can check the calibration of your scale regularly.

Prerequisite

Routine test parameters are set under Maintenance –> Scale test.

If an interval for the routine test is defined (Days > 0), the device automatically asks you to perform the test.

Routine test with external weight

1 Unload the scale.

2 Select External Routine Test in the Quick

Select menu with the cursor keys / and confirm with .

ð You are asked to put the indicated weight on the platform.

3 When the required weight is put on the platform, press

.

ð The routine test is carried out and the test protocol is displayed for a short time.

4 To leave the routine test press .

Routine test with internal weight

Routine test with internal weight is available for ICS685k-.../f compact scales only.

1 Unload the scale.

2 Select Routine Test in the Quick Select menu with the cursor keys / and confirm with

.

ð The routine test is carried out with the internal calibration weight and a test protocol is displayed for a short time.

• The results of the routine test are stored in the routine test log file.

• If the determined weight is not within the tolerance, the test protocol is in red. Call the METTLER

TOLEDO service technician.

Quick Select menu 121

8.8 Performing corner load test

The corner load test gives additional information on the behaviour of your scale.

Prerequisite

Corner load test parameters are set under Maintenance –> Scale test.

If an interval for the corner load test is defined (Days > 0), the device automatically asks you to perform the test.

1 Unload the scale.

2 Select Corner load test in the Quick Select menu with the cursor keys / and confirm with

.

ð You are asked to put the indicated weight on the indicated corner of the platform.

3 When the required weight is put on the platform, press

.

ð The corner load test is carried out for the first corner.

ð You are asked to put the indicated weight on the next indicated corner of the platform.

4 Repeat step 3 until all corners are tested and the following test protocol is displayed for a short time:

122 Quick Select menu

8.9 Calling up routine test / corner load test log files

Prerequisite

Routine test and/or corner load test parameters are set under Maintenance –> Scale test.

Viewing test log file

1 Select Routine Test Log or  Corner load test log in the Quick Select menu with the cursor keys  /  and confirm with .

ð The routine test / corner load test protocol of the last test is displayed.

2 To view other test protocols use the cursor keys

 /  .

Printing test log file

1 When a routine / corner load test record is displayed, press the soft key .

2 In the next screen select either Print current record to print a single record or Print whole memory to print all records.

3 Confirm selection with .

ð The routine test log record(s) is(are) printed.

Deleting routine test / corner load test log file

Deleting routine test / corner load test log files is carried out in the menu under Maintenance –

> ... –> Routine test / Corner load test.

Quick Select menu 123

8.10 Calling up calibration log file

Prerequisite

Calibration procedures are stored in the calibration log file.

Viewing calibration log file

1 Select Calibration Log  in the Quick Select menu with the cursor keys  /  and confirm with

.

ð The calibration protocol of the last calibration is displayed.

2 To view other test protocols use the cursor keys

 /  .

Printing calibration records

1 When a calibration record is displayed, press the soft key .

2 In the next screen select either Print selected record to print a single record or Print whole memory to print all records.

3 Confirm selection with .

ð The calibration record(s) is(are) printed.

124 Quick Select menu

9 Event and error messages

9.1 Error conditions

Error

Display dark

Weight display unstable

Incorrect weight display

Attention: Approval

invalid alternating with metrological data

Cause

• Backlighting set too dark

• No power supply

Remedy

Set backlighting brighter.

Check power supply.

• Unit switched off Switch on unit.

• Power supply cable not plugged in Plug in power supply cable.

• Brief fault Switch device off and on again.

• Unstable installation location

• Draft

• Unstable weighing sample

• Contact between weighing pan and/or weighing sample and surrounding

• Power supply fault

• Incorrect zeroing

-

Adjust vibration adapter.

Avoid draft.

Dynamic weighing.

Remedy contact.

Check power supply

Unload scale, set to zero and repeat weighing operation.

Clear tare.

Remedy contact.

• Incorrect tare value

• Contact between weighing pan and/or weighing sample and surroundings

• Weighing platform tilted

• Load plate not on the scale

• Weighing range not reached

• Weighing range exceeded

-

-

-

Level weighing platform.

Place load plate on the scale.

Set to zero.

Unload scale.

Result not yet stable

Approval was tampered with

Reduce preload.

If necessary, adjust vibration adapter.

Call METTLER TOLEDO service technician.

Event and error messages 125

9.2 Errors and warnings

Error messages

Error messages contain the following information:

Warning - Informationscreen

Out of range!

Enter value within the allowed range

Press 'C' Key to confirm

1

Error message

2

Warning symbol

3

Message identifier

4

How to clear the message

5

Remedy

Warnings

Warnings are displayed briefly and then disappear automatically.

1

Warning message

2

Warning symbol

3

Warning identifier

126 Event and error messages

Information

Information is displayed briefly and then disappears automatically.

Warnung - Informationsbildschirm

Cleared

1

Info message

2

Info symbol

3

Info identifier

Event and error messages 127

9.3 Smart weighing counter / spanner icon

This weighing instrument features several control functions to monitor the condition of the device.

The METTLER TOLEDO service technician can setup and enable these functions.

This helps the user and the METTLER TOLEDO service technician to detemine how the device is treated and what measures are needed to keep it in a good shape.

If the control functions triggers an alert, a message is shown.

You can confirm the message and continue to work with the weighing instrument. The spanner icon lights up.

In case of an alert we strongly recommend calling the METTLER TOLEDO service technician

• to replace parts which are at the end of lifetime,

• to correct wrong settings,

• to educate operators about proper handling,

• to perform routine service work,

• to reset the alert.

The control functions monitor the following conditions:

• number of weighings

• number of overloads

• maximum weight

• zero commands and zero failures

• battery charging cycles

• power-on time

• date for the next service inspection

9.4 Service information

In case you need the METTLER TOLEDO service technician, you can read the necessary system and contact information from the device.

1 Press twice.

ð System information data are displayed.

2 Press again

ð Your contact data are displayed.

128 Event and error messages

10 Technical data and accessories

10.1 Devices for dry environment

10.1.1 Technical data for weighing terminals for dry environments

ICS685 weighing terminals

Housing

Display

Keyboard

Protection type

Aluminium diecast

LCD liquid crystal graphical display, with back lighting

Tactile-touch membrane keypad (PET)

Scratch-resistant labelling

With power supply connection IP65

With built-in storage battery

With exchangeable battery

Weighing platform

IP65

IP5x

IP5x / IP65 (option, not for 0.6XS)

Net weight Weighing terminal 2.0 kg / 4.4 lb

Power supply connection Direct connection to power supply

(supply voltage fluctuation not exceeding ±10 % of the rated voltage)

Rated voltage 100 ... 240 V AC / 50 ... 60 Hz /

300 mA approx. 2.5 m / 8.2 ft

Battery operation

Power cord

Supply of device

Up to 22 hours of operation possible

9-28 VDC power supply Rated voltage

12 V

9 ... 28 V

/ 2.5 A

/ max. 2.5 A

Battery charger

Power cord

Ambient conditions

Ambient conditions Application

Altitude

Temperature range Class III

Temperature range Class II with PBK785 with PBK9-series / PFK9-series approx. 5 m / 16 ft, open ends

0 ... 40 °C / 32 ... 104 °F, dry environment indoor use only up to 2,000 m

–10 ... 40 °C / 14 ... 104 °F

Overvoltage category

Pollution degree

Humidity

II

2

10 ... 30 °C / 50 ... 86 °F

0 ... 40 °C / 32 ... 104 °F

Max. rel. humidity 85 % for temperatures up to 40 °C / 104 °F

W & M approvals OIML Class II, III, IIII

NTEP Class II, III

Interfaces

Optional equipment

Scale interfaces

3 additional optional interfaces possible up to 4 (incl. SICS scale via RS232, SICSpro scale via RS422/RS485) max. 2 analog scales max. 2 IDNet scales (except F cell, AWU cell, GD16, GD17, Pik)

Technical data and accessories 129

10.1.2 Technical data for compact scales for dry environments

• The size of the weighing platform (0.6XS, 3XS, 6XS, 3SM, 6SM, 15LA, 35LA) is indicated at the end of the product name, e.g., ICS685s-3XS/f.

• Other combinations of weighing range and readability can be adjusted by the METTLER TOLEDO service technician on site.

• The table below indicates the factory settings of weighing range and readability.

Weighing ranges and readability ICS685s-.../f compact scales

• Approved resolution 1 x 6,000 e (OIML, NTEP)

• Non-approved resolutions up to 60,000 d

ICS685s-.../f

Capacity

3SM

3 kg

6 lb

6SM

6 kg

12 lb

Readability

Standard resolution: 6,000 d

Optional resolution: 30,000 d

Optional resolution: 60,000 d

Approved resolution: 6,000 e

Repeatability (sd)

Linearity

Weight

0.5 g

0.001 lb

0.1 g

0.0002 lb

0.05 g

0.0001 lb

0.5 g

0.001 lb

0.05 g

0.0001 lb

0.1 g

0.0002 lb

5.5 kg

12.1 lb

1 g

0.002 lb

0.2 g

0.0005 lb

0.1 g

0.0002 lb

1 g

0.002 lb

0.1 g

0.0002 lb

0.2 g

0.0005 lb

5.5 kg

12.1 lb

15LA

15 kg

30 lb

2 g

0.005 lb

0.5 g

0.001 lb

0.2 g

0.0005 lb

2 g

0.005 lb

0.2 g

0.0005 lb

0.5 g

0.001 lb

7.7 kg

17.0 lb

35LA

35 kg

60 lb

5 g

0.01 lb

1 g

0.002 lb

0.5 g

0.001 lb

5 g

0.01 lb

0.5 g

0.001 lb

1 g

0.002 lb

7.7 kg

17.0 lb

130 Technical data and accessories

Weighing ranges and readability ICS685k-.../f and ICS685k-.../DR/f compact scales

• Approved resolution up to 61,000 e (OIML, NTEP)

• Non-approved resolutions up to 610,000 d

• FACT function (Fully Automatic Calibration Technology) calibrates the scale according to temperature changes thus increasing weighing accuracy

ICS685k-.../f

Capacity

0.6XS

0.61 kg

1.2 lb

3XS

3.1 kg

6 lb

6XS

6.1 kg

12 lb

6SM

6.1 kg

12 lb

15LA

15.1 kg

30 lb

35LA

35.1 kg

60 lb

Readability

Standard resolution

Approved resolution

Repeatability (sd)

Linearity

Weight

0.001 g 0.01 g 0.01 g 0.1 g 0.1 g 0.1 g

0.000002 lb 0.00002 lb 0.00002 lb 0.0002 lb 0.0002 lb 0.0002 lb

0.01 g 0.1 g 0.1 g 1 g

0.00002 lb 0.0002 lb 0.0002 lb 0.002 lb

1 g

0.002 lb

1 g

0.002 lb

0.001 g 0.01 g 0.01 g 0.1 g 0.1 g 0.1 g

0.000002 lb 0.00002 lb 0.00002 lb 0.0002 lb 0.0002 lb 0.0002 lb

0.002 g 0.02 g 0.02 g 0.2 g 0.2 g 0.2 g

0.000005 lb 0.00005 lb 0.0005 lb 0.0005 lb 0.0005 lb 0.0005 lb

6.3 kg 5.7 kg 5.7 kg 5.7 kg 9.0 kg 9.0 kg

13.4 lb 12.6 lb 12.6 lb 12.6 lb 19.8 lb 19.8 lb

ICS685k-.../DR/f

Capacity

0.6XS

0.12 kg /

0.61 kg

3XS

0.6 kg /

3.1 kg

6XS

1.2 kg /

6.1 kg

Readability

Standard resolution

Approved resolution

0.001 g /

0.01 g

0.01 g

0.01 g /

0.1 g

0.1 g

0.01 g /

0.1 g

0.1 g

Max. mechanical preload without losing capacity

ICS685

Preload

3SM

1.25 kg

2.76 lb

6SM

3.25 kg

7.17 lb

ICS685

Preload

0.6XS

3XS

1.73 kg

3.81 lb

6XS

0.73 kg

1.61 lb

6SM

1.2 kg /

6.1 kg

0.1 g /

1g

1 g

15LA

3 kg /

15.1 kg

0.1 g /

1g

1 g

35LA

3 kg /

15.1 kg

0.1 g /

1g

1 g

15LA

3.32 kg

7.32 lb

6SM

2.25 kg

4.96 lb

15LA

20.32 kg

44.80 lb

35LA

13.32 kg

29.37 lb

35LA

0.32 kg

0.71 lb

Technical data and accessories 131

10.1.3 Operating life with battery

The operating life during battery operation varies depending on the intensity of use, the configuration and the connected scale.

The following approximate values apply with standard RS232 interface and the brightness set to 5.

Weighing platform

Strain gauge weighing platform

MonoBloc

®

weighing platform

Weighing terminal type Conditions

ICS685g

WLAN, continuous operation

ICS685k

USB host, continuous operation

WLAN, continuous operation

USB host, continuous operation

Duration

16 h

16 h

10 h

10 h

10.1.4 Dimensional drawings for devices for dry environments

ICS685 weighing terminal

248 mm / 9.8" 164 mm / 6.5"

ICS685 compact scale with XS or SM weighing platform

364 mm / 14.3"

130 mm / 5.1"

206 mm / 8.1"

132 Technical data and accessories

ICS685 compact scale with XS weighing platform and windshield

206.9 mm

186 mm

200 mm

186 mm

97 mm

ICS685 compact scale with LA weighing platform

404 mm / 15.9" 514 mm / 20.2"

Technical data and accessories 133

10.1.5 Accessories for dry environments

Accessories for ICS685

Printer RS-P25/01 (for Europe only)

Printer RS-P26/01 (for Europe only)

Printer RS-P28/01 (for Europe only)

Printer APR510 Direct thermal Label Printer, 203 dpi

Printer APR510 Thermal Transfer Label Printer, 203 dpi

Printer APR510 Direct thermal Label Printer, 300 dpi

Printer APR510 Thermal Transfer Label Printer, 300 dpi

Printer APR710 Direct thermal Label Printer, 203 dpi

Printer APR710 Thermal Transfer Label Printer, 203 dpi

Printer APR710 Direct thermal Label Printer, 300 dpi

Protective cover for the weighing terminal, set of 5 pieces

Auxiliary display AD-RS-M7 (requiring cable 22 023 506)

Charging station for Battery pack (lithium ion)

Battery pack, lithium ion

IP5x

IP65

Windshield for ...XS weighing platforms

Wall bracket

Support for wheeled bench stand

Column for PBA655, PBD655 and ICS4_5 / ICS685 compact scales

(requires wall bracket 30 032 637)

Height 330 mm / 1.3 ft

Height 660 mm / 2.6 ft

Floor stand, height 1000 mm / 3.3 ft

Painted steel

Stainless steel

Relaybox 4, for Digital I/O

Power supply for Relaybox 4

Order no.

11 124 300

11 124 304

11 124 301

64 090 256

64 090 257

64 090 258

64 090 259

64 688 858

64 688 859

64 688 861

30 032 638

12 122 381

30 093 236

30 093 237

30 093 238

72 262 929

30 032 637

22 023 460

72 198 699

72 198 700

22 023 451

22 023 503

22 011 967

00 505 544

134 Technical data and accessories

Cables and plugs for ICS685

Cables

Cable M12 USB Female Type A, USB Host

0.2 m / 0.7 ft

3 m / 10 ft

Cable M12 USB Male Type A, USB device, 3 m / 10 ft

Cable M12 RS232 Female Sub D 9 pin (crossed; used for PC)

Cable M12 RS232 Male Sub D 9 pin (not crossed; used for SICS scale)

Cable M12 RS422/485, open ends

Cable M12 Digital I/O, open ends

Cable M12 Ethernet RJ45

5 m / 16 ft

20 m / 66 ft

Cable for auxiliary display AD-RS-M7

RS232 extension 0.5 m / 1.6 ft, incl. 5 V and 12 V

RS232 SICS (cross, M12 plug male / M12 male) 3 m

RS422/485 extension kit

SICSpro extension (M12 male / M12 female)

3 m / 10 ft

10 m / 32 ft

SICSpro extension (M12 male / open end) 5 m / 16 ft

Cable for GA46

0.4 m / 1.4 ft

2.5 m / 8 ft

Plugs

RS232 Counter plug (8 pin; for compact scales, extension 30 035 358 required)

Ethernet Counter plug (4 pin, D; not for compact scales)

USB Device Counter plug (4 pin, A; not for compact scales)

Order no.

22 017 604

22 017 608

22 018 967

22 017 601

22 017 602

22 017 603

22 018 969

22 017 610

22 017 614

22 023 506

30 035 358

22 023 528

22 023 698

22 023 696

30 024 759

30 024 768

22 018 978

22 018 979

22 022 056

22 022 058

22 022 059

Technical data and accessories 135

10.2 Devices for wet environment

10.2.1 Technical data for weighing terminals for wet environments

ICS689 weighing terminals

Housing Stainless steel 1.4301 or AISI 304

Display

Keyboard

Protection type

Net weight

LCD liquid crystal graphical display, with back lighting

Tactile-touch membrane keypad (PET)

Scratch-resistant labelling

Terminal

Standard weighing platform

IP68/IP69k

IP65

IP65/IP67 Weighing platform with option potted stainless steel load cell

Weighing platform with option hermetically sealed stainless steel load cell

Weighing terminal

IP68/IP69k

ICS689g.../c

2.0 kg / 4.4 lb

3.2 kg / 7.1 lb

+ weight of the weighing platform

Power supply connection Direct connection to power supply

(supply voltage fluctuation not exceeding ±10 % of the rated voltage)

Rated voltage 100 ... 240 V AC

50 ... 60 Hz

300 mA

12 V / 2.5 A Battery operation Supply of device

Up to 22 hours of operation possible

9-28 VDC power supply Rated voltage

Battery charger

Power cord

Ambient conditions

9 ... 28 V / max. 2.5 A approx. 5 m / 16 ft, open ends

Ambient conditions

0 ... 40 °C / 32 ... 104 °F dry environment indoor use only Application

Altitude

Temperature range Class III

Temperature range Class II

Overvoltage category

Pollution degree

Humidity up to 2,000 m

–10 ... 40 °C / 14 ... 104 °F

0 ... 40 °C / 32 ... 104 °F

II

2

Max. rel. humidity 80 % for temperatures up to 40 °C / 104 °F

W & M approvals OIML Class II, III, IIII

NTEP Class II, III

Interfaces

Optional equipment

Scale interfaces

3 additional optional interfaces possible up to 4 (incl. SICS scale via RS232, SICSpro scale via RS422/RS485) max. 2 analog scales max. 2 IDNet scales (except F cell, AWU cell, GD16, GD17, Pik)

136 Technical data and accessories

10.2.2 Technical data for terminal and platform combinations for wet environments

• The size of the weighing platform (A, BB, B, BC, CC, QA, QB, QC) is indicated at the end of the product name, e.g., ICS689g-QA6.

• Other combinations of weighing range and readability can be adjusted by the METTLER TOLEDO service technician on site.

• The table below indicates the factory settings of weighing range and readability.

Weighing ranges and readability

Model

Weighing range

Readability

A3

1.5 kg / 3 kg

2.5 lb / 5 lb

0.5 g / 1 g

0.0005 lb / 0.001

lb

A6 / QA6

3 kg / 6 kg

5 lb / 10 lb

A15 / QB15

6 kg / 15 kg

10 lb / 25 lb

BB30 / B30 / QB30

15 kg / 30 kg

25 lb / 50 lb

1 g / 2 g 2 g / 5 g 5g / 10 g

0.001 lb / 0.002 lb 0.002 lb / 0.005 lb 0.005 lb / 0.01 lb

Model

Weighing range

Readability

BB60 / B60 /

BC60 / CC60 /

QB60 / QC60

B150 / BC150 /

CC150 / QC150

BC300 / CC300 CC600

30 kg / 60 kg kg 60 kg / 150 kg kg 150 kg / 300 kg 300 kg / 600 kg

50 lb / 100 lb 100 lb / 250 lb

10 g / 20 g 20 g / 50 g

0.01 lb / 0.02 lb 0.02 lb / 0.05 lb

250 lb / 500 lb

50 g / 100 g

0.05 lb / 0.1 lb

500 lb / 1000 lb

100 g / 200 g

0.1 lb / 0.2 lb

Operation limits – maximum static safe load

Model

A

BB

B

BC

CC

QA

QB

QC a – center load

30 kg

60 lb

100 kg

200 lb

200 kg

400 lb

400 kg

800 lb

700 kg

1400 lb

15 kg

30 lb

100 kg

200 lb

200 kg

400 lb

b – side load

20 kg

40 lb

70 kg

140 lb

140 kg

280 lb

300 kg

600 lb

400 kg

800 lb

10 kg

20 lb

70 kg

140 lb

140 kg

280 lb

c – corner load

10 kg

20 lb

35 kg

70 lb

75 kg

150 lb

150 kg

300 lb

200 kg

400 lb

5 kg

10 lb

35 kg

70 lb

75 kg

150 lb

a b c

Technical data and accessories 137

Weights, approximate values

Model

A

BB

B

BC

Weight

5.2 kg

11.5 lb

7.4 kg

16.3 lb

12.7 kg

28.0 lb

26.5 kg

58.4 lb

Length of load cell cable for ICS689g-.../t

Weighing range

up to 30 kg / 50 lb

60 kg / 100 lb and higher

Length in m

1.5

2.5

Model

CC

QA

QB

QC

Weight

35.0 kg

77.2 lb

4.1 kg

9.0 lb

7.8 kg

17.2 lb

13.1 kg

28.9 lb

Length in ft

5

8

10.2.3 Operating life with battery

The operating life during battery operation varies depending on the intensity of use, the configuration and the connected scale.

The following approximate values apply with standard RS232 interface and the brightness set to 5.

Weighing platform

With 1 strain gauge load cell, e.g., ICS689g-A15...

With 4 strain gauge load cells, e.g., a floor scale

With PBK98_/PFK98_

Conditions

Continuous operation

Continuous operation

Continuous operation

Duration

25 h

22 h

14 h

138 Technical data and accessories

10.2.4 Dimensional drawings for devices for wet environments

ICS689 weighing terminal

a

Dimension a b c

[mm]

260

170

114 c

60

["]

10.24

6.70

4.49

Technical data and accessories 139

Weighing platforms for ICS689 terminal and platform combinations

Front view Side view

f g d e

Dim.

a b c h

Dim.

c d a b g h f e

[mm]

175

240

56

95

235

300

22

A BB B

["]

6.89

9.45

2.20

3.74

9.25

[mm]

235

300

57

97

335

["]

9.25

11.81

2.24

3.82

13.81

[mm]

335

400

57

100

435

["]

13.19

15.75

2.24

3.94

17.13

11.81

0.87

400

16

15.75

0.59

500

15

19.69

0.59

650

15

Circle diameter: 30 mm / 1.18 "; diagonal: 34 mm / 1.34 "

[mm]

435

500

70

108

587

BC

["]

17.13

19.69

2.76

4.25

23.11

25.59

0.59

CC QA QB

[mm]

503

["]

19.80

600 23.62

79 3.11

130

724

800

5.12

28.50

31.50

21

[mm]

170

229

56

95

170

229

["]

6.69

9.02

2.20

3.74

6.69

9.02

[mm]

233

305

57

108

245

305

["]

9.17

12.01

2.24

4.25

9.65

12.01

[mm]

392

457

60

100

397

457

0.83

22 0.87

15 0.59

15

Circle diameter: 30 mm / 1.18 "; diagonal: 34 mm / 1.34 "

QC

["]

15.43

17.99

2.36

3.94

15.63

17.99

0.59

140 Technical data and accessories

ICS689g-.../f terminal and platform combination

a

Dim.

a

Dim.

a

A

[mm]

418

["]

16.46

[mm]

772

CC

["]

30.39

[mm]

485

BB

["]

19.09

[mm]

407

QA

["]

16.02

B

[mm]

581

["]

22.87

[mm]

489

QB

["]

19.25

[mm]

681

BC

["]

26.81

[mm]

640

QC

["]

25.10

Technical data and accessories 141

ICS689g-.../c terminal and platform combination

The size of the weighing platform (A, BB, B, BC, CC, QA, QB, QC) is indicated at the end of the product name, e.g., ICS689a-QA6.

Dim.

a b c

Dim.

a b c

[mm]

337

A

["]

13.27

[mm]

691

CC

["]

27.2

[mm]

404

BB

["]

15.91

[mm]

500

412 mm / 16.22 "

34 mm / 1.34 "

B

["]

19.69

[mm]

326

QA

["]

12.83

[mm]

408

412 mm / 16.22 "

34 mm / 1.34 "

QB

["]

16.06

[mm]

600

BC

["]

23.62

[mm]

559

QC

["]

22.01

142 Technical data and accessories

10.2.5 Accessories for wet environments

Accessories for ICS689

GA46 printer, RS232, incl. 8-pin M12 plug cable 2.5 m / 8.2 ft cable 0.4 m / 1.3 ft

I/O accessories

Relaybox 4, for Digital I/O

Power supply for Relaybox 4

Mechanical parts

Protective cover for terminals ICS689, set of 3 pieces

Stand ICS689, for .../t version or terminal with PBA430

Height 50 mm / 0.16 ft

Height 330 mm / 1.1 ft

Height 660 mm / 2.2 ft

Stand ICS689 for PBK, PFK, MA, MD and DB Platforms, height 330 mm / 1.1 ft

Bench stand ICS689 for scale bench 00 503 632 or 00 504 854, height 500 mm / 1.6 ft

Floor stand ICS689, height 1000 mm / 3.3 ft

Standbase for floor stand

Wall bracket ICS689, inclinable and swivelling

Desk mounting plate, for terminal and .../t version only

Cables and plugs for ICS689

Cables

RS232 cable for SICS scale, 8 pin M12 <–> 9 pin sub D plug, 3 m / 10 ft

RS232 cable for PC, 8 pin M12 <–> 9 pin sub D receptacle, 3 m / 10 ft

RS422/RS485 cable, 6 pin M12 <–> open ends, 3 m / 10 ft

Ethernet cable, 4 pin M12 coding D <–> RJ45

5 m / 16.4 ft

20 m / 65.6 ft

Cable to connect Digital I/O option with relay box,

12 pin M12 <–> open ends, 10 m / 32.8 ft

USB Device cable, connection to PC, 3 m / 10 ft

USB Host cable, connection to scanner, keyboard or USB stick, M12 USB female type A

0.2 m / 0.7 ft

3 m / 10 ft

Plugs

RS232 counter plug, 8 pin M12 (for .../f versions extension 30 035 358 required)

Ethernet counter plug, 4 pin, coding D, M12 (not for .../f versions)

USB Device counter plug, 4 pin, coding A, M12 (not for .../f versions)

RS422/485 extension kit

Order no.

22 021 087

22 021 088

22 021 089

22 021 090

22 021 091

22 021 093

22 021 092

30 093 252

30 093 253

22 022 056

22 022 058

22 022 059

22 023 698

Order no.

22 019 925

22 019 926

22 011 967

00 505 544

22 021 110

22 018 057

22 013 964

22 013 965

22 014 836

22 014 835

22 014 834

22 011 982

22 014 833

22 021 111

Technical data and accessories 143

10.3 General technical data

10.3.1 Applications

• Weighing

• Piece counting

• Over/Under Checkweighing

• Filling

• Classifying

• Totalizing

• Prompting

• Average weighing

• Internal database with up to 5000 records

• Alibi log file

• Routine test function

• Calibration log file

• User management

10.3.2 Analog scale interface

Impedance

Excitation

Sensitivity

Max. resolution

Min. verification interval

≥ 87.5 Ohm, e.g., 1 x 350 Ohm or 4 x 350 Ohm

3.3 V DC

2 to 3 mV/V

7,500 e (OIML)

300,000 d (non approvable)

0.264 µV/e

10.3.3 Assignment of the interface connections

Digital I/O RS232 RS422 RS485 USB Device

USB Host

Ethernet Power

Socket

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

Pin 9

Pin 10

Pin 11

Pin 12

* max. 0.5 A

In 0

In 1

In 2

In 3

In_GND

Out 0

Out 1

Out 2

Out 3

Out_GND

+12 V *

GND

CTS

TxD

RTS

RxD

+12 V *

+5 V *

GND

TxD

TxD–

RxD

+12 V *

GND

RxD–

T/RxD

¨T/RxD–

+12 V *

GND

+5 V *

D–

GND

D+

TD+

RD+

TD–

RD–

+12 V *

+12 V *

GND

GND

144 Technical data and accessories

11 Appendix

11.1 Metrological information

Scales that have been factory-calibrated have a label indicating this on the packaging.

Scales with a green M on the type plate are ready for operation.

Scales that are calibrated in two stages have a label indicating this on the packaging.

These scales have only been calibrated in a first stage (declaration of conformity in accordance with EN 45501-8.2). The second stage of the calibration must be done on-site by authorized service personnel. Please contact your local representative.

M

M

Medium accuracy scales that are used in commerce where certified calibration is required must be calibrated and certified.

Observe the respective measurement data guidelines in your country.

11.2 Table of Geo Code values

For weighing instruments verified at the manufacturer’s, the Geo Code value indicates the country or geographical zone for which the instrument is verified. The Geo Code value set in the instrument

(e.g. "Geo 18") appears briefly after switching on.

Table "Geo Code values 3000e" shows the Geo Code values for European countries.

Table "Geo Code values 6000e/7500e" shows the Geo Code values for different gravitation zones.

Geo Code values 3000 e, OIML Class III (European Countries)

Country

Austria

Belgium

Bulgaria

Croatia

Czechia

Denmark

Estonia

Finland

France

Germany

Greece

Hungary

Iceland

Ireland

Italy

Latvia

* factory setting

Geographical latitude

46°22’ – 49°01’

49°30’ – 51°30’

41°41’ – 44°13’

42°24’ – 46°32’

48°34’ – 51°03’

54°34’ – 57°45’

57°30’ – 59°40’

59°48’ – 64°00’

64°00’ – 70°05’

41°20’ – 45°00’

45°00’ – 51°00’

47°00’ – 55°00’

34°48’ – 41°45’

45°45’ – 48°35’

63°17’ – 67°09’

51°05’ – 55°05’

35°47’ – 47°05’

55°30’ – 58°04’

25*

26

17

19*

20

15

19

26

22

17

23

18

20

23

24

Geo

Code

18

21

16

Country

Liechtenstein

Lithuania

Luxemburg

Netherlands

Norway

Poland

Portugal

Romania

Slovakia

Slovenia

Spain

Sweden

Geographical latitude

47°03’ – 47°14’

53°54’ – 56°24’

49°27’ – 50°11’

50°46’ – 53°32’

57°57’ – 64°00’

64°00’ – 71°11’

49°00’ – 54°30’

36°58’ – 42°10’

43°37’ – 48°15’

47°44’ – 49°46’

45°26’ – 46°35’

36°00’ – 43°47’

55°20’ – 62°00’

62°00’ – 69°04’

Switzerland

Turkey

45°49’ – 47°49’

35°51’ – 42°06’

United Kingdom 49°00’ – 55°00’

55°00’ – 62°00’

15

18

19

18

15

24*

26

Geo

Code

18

22

20

21

24*

26

21

18

16

21*

23

Appendix 145

Geo Code values 6000 e / 75000 e, OIML Class III (Altitude < 1000 m)

Geographical latitude

00°00’ – 12°44’

05°46’ – 17°10’

12°44’ – 20°45’

17°10’ – 23°54’

20°45’ – 26°45’

23°54’ – 29°25'

26°45’ – 31°56’

29°25’ – 34°21’

31°56’ – 36°41’

34°21’ – 38°58’

36°41’ – 41°12’

38°58’ – 43°26’

41°12’ – 45°38’

* factory setting

Geo Code

18

21

16

18

20

23

24

25*, 26

17, 19*

20

15

19

26

Geographical latitude

43°26’ – 47°51’

45°38' – 50°06'

47°51’ – 52°22’

50°06’ – 54°41’

52°22’ – 57°04’

54°41’ – 59°32’

57°04’ – 62°09’

59°32’ – 64°55’

62°09’ – 67°57’

64°55’ – 71°21’

67°57’ – 75°24’

71°21’ – 80°56’

75°24’ – 90°00’

11.3 Disposal

In accordance with the requirements of European Directive 2002/96 EC on Waste

Electrical and Electronic Equipment (WEEE), this device may not be disposed of with domestic refuse. This also applies for countries outside the EU in accordance with their respective national regulations.

Geo Code

18

22

20

21

24*, 26

21

15

18

19

18

15

24*, 26

18

Please dispose of this product in accordance with local regulations for the separate collection of waste electrical and electronic equipment.

Should you have any questions, please contact the corresponding authorities or the dealer from whom this device was purchased.

If this device is passed on (for example for further private or commercial/industrial use), this regulation is also to be passed on.

Many thanks for your contribution to the protection of the environment.

Battery disposal

Batteries contain heavy metals and therefore cannot be disposed of in the normal refuse.

Observe local regulations on the disposal of materials that are hazardous to the environment.

146 Appendix

11.4 Protocol printouts

Examples of what can be adjusted (GA46 printouts, in English)

Printout with header and identification data Over/Under Checkweighing default printout

Piece counting

Classifying – standard printout

Over/Under Checkweighing minimum printout

Classifying – minimum printout

Appendix 147

Index

A

Accessories for dry environment for wet environment

Application

Clever print

Average weighing

Operation

Settings

C

Calibration

Calibration log file

Classifying

Class definition

Display

Procedure

Settings

Cleaning in dry environment in wet environment

Clever print

Connections

Power supply

Weighing platform

Corner load test

Counting

APW optimization

Auto clear APW

Autosampling

Bulk scale

Counting accuracy

Counting system

Procedure

Reference scale

Total count

Custom unit

 45

 45

 33, 82

 26

 26

 122

 85

 47

 85

 85

 84

 85

 84

 84

 85

 85

 73

 124

 58

 59

 59

 89

 134

 143

 82

 34

 82

D

Database

Internal

Quick Select menu

Settings

Digital I/Os

Dimensional drawings

Devices for dry environment

Devices for wet environment

Display

3-line mode

Metrological data line

Settings

Symbols and info line

Units

Update

Weight value

Dynamic weighing

Operation

Settings

E

Energy save

Error conditions

Error messages

External input

Entry

Settings

F

FACT

Settings

Symbol

Filling

Procedure

Quickstart

Subtractive weighing

Target values

To zero

Tolerance type

Filter

 10

 13

 99

 14

 74, 77

 79

 13

 34

 82

 117

 116

 93

 111

 132

 139

 98

 125

 126

 35

 108

 75

 14

 55

 56

 56

 54

 57

 53

 75, 79

148 Index

G

Geo code

Display

Values

H

High resolution

Hygienically sensitive areas

I

Identification

Identifications

Scale data

Terminal data

Weighing data

Info key

Displaying information

Settings

Information

Interfaces

Pin assignment

K

Keyboard

Function keys

Settings

Soft keys

L

Levelling

Linearization

Location

Login

Logout

 91

 71, 77

 98

 35

 33

 99

 127

 144

 29

 145

 35

 28

 15

 99

 16

 25

 73

 25

 29

 29, 115

M

Maintenance

Memory

Backup

Mode

Menu

Analog scale

Application

Communication

Display

IDNet Scale

Maintenance

Operation

Operator menu

Scale

Supervisor menu

Metrological data line

Metrological information

MinWeigh

Settings

Symbol

O

Over/Under Checkcounting

Target values

Over/Under Checkweighing

Display

Output

Procedure

Quick start

Subtractive weighing

Target values

To zero

Tolerance type

P

Printing

Clever print

Printout configuration

Prompt

Additive tare

Hands free

Multi tare

Sample/Tare

Take away

Tare/Sample

Protocol printouts

 33

 33

 81

 41

 39

 40

 38

 42

 37

 147

 54

 88

 87

 55

 56

 56

 54

 57

 53

Index 149

 113

 92

 92

 71

 81

 102

 68

 77

 113

 67

 67

 70

 67

 13

 145

 75, 79

 14

Q

Quick Select menu

R

Reset

Application

Reset all

Scale

Terminal

Resolution

Restart

Routine test

S

Safety instructions

Service information

Smart weighing counter

Spanner icon

Statistics

Storage battery

Straight weighing

Supervisor menu access

Switching on/off

Switching scales

Switching units

 115

 95

 114

 76, 79

 101

 74

 74, 78

 121

 7

 128

 128

 9, 128

 65, 91

 27

 29, 81

 100

 29

 36

 30

T

Taring

Automatic

Automatic clearing the tare

Chain tare

Clearing the tare

Manual

Settings

Tare preset

Technical data

Compact scales

Terminal and platform combinations

Weighing terminals for dry environment

Weighing terminals for wet environment

Templates

Assigning

Defining

Testing

Communication

Display

Keyboard

Scale

Totalization

U

User management

V

Verification test

W

Warning

Z

Zeroing

Automatic

Manual

Settings

 30

 30

 74, 78

 31

 30

 31

 30

 30

 74, 78

 32

 130

 137

 129

 136

 81

 112

 114

 114

 114

 113

 61, 90

 100

 46

 126

150 Index

Mettler-Toledo (Albstadt) GmbH

D-72458 Albstadt

Tel. +49 7431-14 0

Fax +49 7431-14 232 www.mt.com

Subject to technical changes.

© Mettler-Toledo (Albstadt) GmbH 04/2015

30243688B en

www.mt.com

Further information

*30243688*

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement