INSTRUCTIONS
WOpet Patrol WiFi Feeder
F07
【CONTENTS】
Product Specification ......…………………………………………………1
Hardware installation and introduction ..………………………………2
Software Installation ........…………………………………………………5
Add pet feeder via normal mode (EZ mode) ……………………5
Add pet feeder via AP mode ....……………………………………10
Add pet feeder via Auto Scan mode .……………………………13
Feeding ............................…………………………………………………15
Manual feeding ........…………………………………………………15
Scheduled feedin.....…………………………………………………16
Voices recording ......…………………………………………………18
Feeding records and alarm ..………………………………………20
Other.................................…………………………………………………21
Basic settings ...........…………………………………………………21
Advanced settings ...…………………………………………………22
Battery .......................…………………………………………………24
FAQs ................................…………………………………………………26
FCC warnings .................…………………………………………………29
Product Specification
Product Name: WOPET Smart Pet Feeder
Capacity: 6L
Model: F07
Food size: Between 5-15mm
Auto feeder meals: 15 meals
Material: ABS
Color: White
Feeding type: Manual & Automatic
Wi-Fi: IEEE 2.4GHz
Food type: Dry food only
Voice message limit: 10s
Power: DC 5V1 .OA
Power: 5W
Battery: 3 x D batteries (not included)
Product dimensions: 7.6 x 14 x 14.2 inches
APP: Pet Zero APP (Common in Android and iPhone)
1
Hardware installation and introduction
1.
Open the battery compartment at the bottom of the feeder,
insert the Micro USB power cord into the connector and
extend it out along the designed wire guide.
2.
Plug in the feeder and turn on the power switch.
Power
switch
2
Note:
You can also use 3 D cell batteries, which enables the feeder to
work automatically according to your scheduled feeding plan
even without an external power supply.
3.
Rotate the knob on the top cover and take out the feeding
tray. Place the feeding tray into the feeder from the front, then
pour pet food into the feeder.
OFF
ON
Note:
We recommend using only dry food between 5-15mm
in size.
Wet food and damp food are strictly prohibited from being
3
placed in the feeder.
4.
For your pet's health, please wash the grain bucket and
feeding tray regularly. The feeder body should not be filled
with water. Please wipe it with a wrung-out wet cloth.
5.
Operation panel introduction
Indicator LED
Microphone
Recording
Buzzer
Wi-Fi
Settings
Manual Feed
4
Software Installation
Add pet feeder via normal mode (EZ mode)
1.
Search the App Store or scan the QR code below to download
and install Pet Zero.
2.
Run the App, read and agree to the privacy policy, and register
a new account or log in to a registered account (please choose
the correct country or area).
Note:
When you log in, the App will ask you to access certain
permissions. These permissions are very important for the App,
5
please allow them.
3.
Click Add Device or
to add a new pet feeder. Choose the
Add manually tab and select Wi-Fi Pet Feeder.
6
4.
Check whether the indicator LED is flashing RED 2 times per
second.If yes, then click Indicator to go to the next step.If not,
please long press the Wi-Fi Settings button for 3 seconds until
you hear a “beep” sound. Then the feeder's indicator LED will
flash rapidly.
Flashing
rapidly
Long
press
7
Indicator LED status
Flashing rapidly in RED
Feeder is waiting for Wi-Fi network
configuration; it is in normal and auto scan
mode.
Flashing slowly in RED
Feeder is waiting for Wi-Fi network
configuration; it is in AP mode.
Always on in RED
Feeder is configured for the Wi-Fi network
and trying to connect. If the connection
fails, it will always be red.
Always on in BLUE
Feeder is connected to the Wi-Fi network. It
can be turned off in the settings.
Flashing in BLUE
Feeder is feeding.
5.
If the App asks for the location permission from your mobile
phone, please allow it. Then the name of your Wi-Fi network will
appear in the textbox automatically. Next, please enter the
corresponding Wi-Fi password and click Confirm (Please choose a
2.4Ghz Wi-Fi signal instead of a 5Ghz signal, as the feeder doesn’t
support 5Ghz Wi-Fi networks)
8
Important Notice:
Please choose a 2.4Ghz Wi-Fi signal instead of a 5Ghz signal. The
feeder does not support 5Ghz Wi-Fi networks.
b When entering the password, be aware that it is case sensitive.
Please choose a Wi-Fi network with WPA or WPA2 encryption
instead of WEP encryption.
Make sure that MAC address filtering and wireless device isolation
is turned off on the wireless router.
e The feeder may not support a Wi-Fi signal from a wireless
repeater.
9
6.
The feeder will then try to connect to the Wi-Fi network. When
connected, click “Done” to complete adding process.
If the feeder fails to connect, please check the important notice
above first.
If the feeder still fails to connect, please add the feeder via AP
mode by the following instructions below.
Add pet feeder via AP mode
If the feeder fails to connect to the Wi-Fi network, AP mode is plan
B for adding the feeder.
10
1.
Choose Switch Pairing Mode or choose AP mode manually in the
adding process.Then click Indicator is flashing slowly.
Check that the indicator LED is flashing RED once every 3 seconds.
Then click Indicator is flashing slowly.
If the indicator is in another status, please long press the Wi-Fi
button for 3 seconds until you hear a “beep” sound to switch
indicator's status to flashing rapidly. Then long press the Wi-Fi
button again to switch indicator's flashing status to flashing
slowly.Then click Indicator is flashing slowly.
11
2.
Please check the name of the 2.4Ghz Wi-Fi network and enter the
password in the same way as in normal mode. Click Confirm and
the App will ask you to switch your mobile phone's network to a
new network broadcast by the feeder.
3.
Please go to Wi-Fi settings on the mobile phone and connect to
the Wi-Fi that starts with “SmartLife-”. No password is necessary.
Return to the App after the Wi-Fi is connected. The adding
process is the same as in normal mode covered above.
12
Add pet feeder via Auto Scan mode
Please note that in auto scan mode, 100% success rate for
connecting the feeder to the Wi-Fi network cannot be guaranteed.
13
1.
Choose Auto Scan Mode on the Wi-Fi pet feeder page and enter
the correct name and password of the 2.4GHz Wi-Fi network.
Make sure the feeder's indicator LED is flashing RED rapidly.
2.
Wait for the feeder to connect to the Wi-Fi network and appear in
the App.
14
Feeding
Manual feeding
1.
Enter feeder's main interface. Click Manual feed, choose the
feeding portions and click “OK”. The feeder will feed immediately.
2.
You can also double click the Manual feed button to feed
manually. The feeding amount can be adjusted in the App: Click
and set up Feed portions using the button. Setting it to 0
will disable this function.
15
Scheduled feeding
The pet feeder supports the scheduled feeding of exact portions
at exact times.
1.
Click the
button in App, choose feeding time, repeat rules
for each day of the week, and feed portions, then click Save.
16
2.
The feeder supports up to 15 feeding schedules. If you need to
disable a schedule, you can do so by disabling its switch.You can
also delete it by swiping the feeding schedule to the left access the
delete option.
17
Voice recording
1.
To develop good feeding habits for pets, the feeder supports
pre-recording a maximum of 10 seconds of audio, which is played
during feeding.
2.
Press and hold the record button for 3 seconds until the feeder
makes a “Drip” sound, then you can start talking at the microphone
position. Note that the recording button should be pressed
continually. After the recording is complete, release the button, the
feeder will make two “Drip” sounds.
3.
After recording is complete, you can preview the recorded audio
by short pressing the record button. If you need to change the
recording, please re-record it. The closer you are to the
microphone, the louder your voice will be.
4.
The default voice recording playback is 3 times. It can be set
to a maximum of 5 times. Click
and set up Voice playing times.
Setting it to 0 will disable the feeding audio function.
18
Note:
When the pet feeder is connected to the regular power adapter,
the pet feeder recording will be played during feeding. It will play
the number of set times until the feeder has finished feeding.
b If pet food blocks the food tray, the pet feeder will stop feeding
and wait for 10 minutes. The voice recording will be played 1 time
per minute to call the pet. If the pets finish the food in the tray, the
pet feeder will work as scheduled in the feeding plan. Otherwise, it
will stop feeding if the pets still do not finish feeding after 10
minutes.
The voice recording will not play when feeding by button.
19
Feeding records and alarm
1.
After feeding, there will be feeding records in the App. Click
to check the feeding records. The feeding records of the last 7
days will be shown.
2.
When the food level is insufficient or zero, “lack of food” message
will appear on the
3.
page.
Machine malfunctions include low or empty food storage, low
battery and food jammed in the feeding bucket or feeding tray.
20
4.
When a malfunction occurs, a message will appear in the App. You
can check error messages in the message center. Make sure that
prompt message (notification) is enabled.
Other
Basic settings
Battery Status: Shows the status of the battery.
Indicator lights: Turns the indicator on/off when the feeder
is connected to the Wi-Fi network.
Reboot feeder: Reboots the feeder manually.
21
Advanced settings
Click
to access the advanced settings page.
Device information: Check feeder information. Please make sure
that the time zone of the feeder is correct. It should be the same
as the mobile phone's time zone when adding the feeder. If it is
incorrect, the feeder may feed at incorrect times, so please remove
the feeder and add it again.
22
Offline notification: When the feeder is offline, a notification will
sent to your mobile phone.
Share device: If you want to add the feeder to another mobile
phone, register a new account on the new mobile phone, then
share the device with the new account. Please make sure that both
accounts are in the same country or area when registering them.
23
Remove device: There are 2 options that will both remove the
device from the App but not delete the settings in the feeder. You
could re-configure the feeder's Wi-Fi network using these 2
options. If you wish to remove all the settings in the feeder, please
long press the Wi-Fi button on the feeder until you hear a “beep”
sound.
Battery
The back-up battery is designed as a short-term alternative for
when the external power supply is cut. When the pet feeder works
on battery back-up, it will go into sleep mode and some functions
will be limited :
When there is battery supply only, the voice recording will only
play once before feeding the pets. It will not play during feeding.
b When there is battery supply only, the feeder's Wi-Fi connection
will be disconnected. All the operations on the App will be
unavailable.
24
These measures are designed to save battery energy to ensure
that the pet feeder can keep working for a long time.
25
FAQs
1.
Why did the feeder fail to connect to my Wi-Fi network?
Please check the important notice on Page 6 for help. You can
try to add the feeder via AP mode instead of normal mode and
auto scan mode.
2.
Why is the feeding recording only played once or never when
I set the recording multiple times?
Please press and hold the record button to record your voice
first. If the feeder is working on battery supply only, the
recording will only play once before feeding.
26
3.
Why does the feeder feed at the wrong time?
Please check that the time zone of the feeder is correct. You can
find help about time zone information on page 15.
4.
Why does it always prompt that food is blocking the feeding
tray when this is not the case?
Once food falls into the tray, the feeder will wait for 10 minutes
for the pet to eat the food. If the pet does not come to eat
during this time, the feeder will send a message that food is
blocking the feeding tray. If the pet eat the food after 10
minutes, and you still receive the message, it is also possible
that food is stuck in the food slot. If that is the case, clean
the food slot.
27
5.
Why is the indicator LED still flashing after I disabled it?
When it is feeding, the indicator LED cannot be disabled.
6.
How can I restore the feeder to factory default settings?
Please long press the Wi-Fi settings button for 3 seconds until
you hear a beep sound.
28
WARNING:
Changes or modifications to this unit not expressly
approved. Non-compliance could void the user's
authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
29
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
30
Reorient or relocate the receiving antenna.
Increase the distance between the equipment
and receiver.
Connect the equipment into an outlet on a different
circuit from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Shielded interface cables must be used with the
equipment in order to comply with the limits for a
digital device pursuant to Subpart B of Part 15 of
FCC Rules. Specifications and designs are subject to
change without any notice or obligation on the part
of the manufacturer.
31
https://www.facebook.com/wopetworld
">
