Module type Temp. Controller (Event Input/Output

Module type Temp. Controller (Event Input/Output
Instruction Manual (Installation)
1-2
Multi-loop module type Temperature Controller
-- When installing or removing the equipment, turn the power OFF. Otherwise, shock,
operational errors or failures may be caused.
-- Periodic maintenance is recommended for continuous and safe use of this
equipment.
-- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
-- The warranty period for this unit (including accessories) is one year, if the product is
used properly.
Event Input/Output Module
Model : PUME
INP-TN1PUMEa-E
Thank you for purchasing the Fuji module type temperature controller.
Once you have confirmed that this is the product you ordered, please use it in
accordance with the following instructions.
For detailed information on operating this equipment, please refer to the separate
user's manual.
In addition, please keep this instruction manual within easy reach of the actual person
using this equipment.
The contents of this manual are subject to change without notice.
This manual is complied with possible care for the purpose of accuracy, however,
Fuji Electric shall not be held liable for any damages, including indirect damage,
caused by typographical errors,
absence of information or use of information in this manual.
Confirming Specifications and Accessories
Related Information
Refer to "Module Type Temperature
Controller Event Input/Output Module
User's Manual" for details about the
items described in this manual.
Temperature Controller Event input/
output Module
1 Unit
Instruction Manual 1 Copy
Content
Material
name
Specification Catalog
Operating
Event Input
instruction
/ Output
module
User's
manual
Tool
PUM
parameter
loader
ECNO 1162
INPTN5A0199-E
Please Read First (Safety Warnings)
Improper use of the equipment may cause injury to the user or property
damage.
1
Warning
1-1
Installation and Wiring
-10 to 50 degree C
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
Installation category
IEC1010-1: class II
Pollution level
IEC1010-1: degree 2
2-4
• Note that the insulation class for this equipment is as follows. Before installing,
please confirm that the insulation class for equipment meets usage requirements.
Power
Loader communication
RS-485 communication
Cautions when Mounting to Cabinets / DIN rails
Cautions for Wiring
-- Input signal wire and output signal wire should be separated from each other. And
both should be shielded.
-- If the output operation frequency is high, selecting a SSR/SSC drive output type is
recommended.
[Proportionate cycles] Relay output: 30 sec. or more, SSR/SSC drive output: 1sec.
or more
-- When inductive loads such as magnetic opening/closing equipment, etc. as relay
output equipment are connected, use of "Z-trap," manufactured by Fuji Electric
Device Technology Co., Ltd., is recommended in order to protect the contacts against
opening/closing surges and to ensure long-term use.
21
11
Model names
: ENE241D-07A
22
12
(For 100V power voltage)
23
13
: ENE471D-07A
24
14
(For 200V power voltage)
25
15
Attachment position : Please connect between the
26
16
relay control output contacts.
27
17
-- To comply with CE marking (EMC), we recommend to
28
18
attach ferrite core to communication cable and power
cable.
29
19
-- For wiring to the terminal block, apply crimp type
30
20
terminals size M3.
Z-trap connecting diagram
Screw size
: M3 x 7 (with square washer)
Screw tightening torque: 0.78N-m (8kgf-cm)
-- To avoid the influence of inductive noise, input signal wires should be separated from
electric power lines or load lines.
• This equipment is intended to be used under the following conditions.
Ambient temperature
Cautions when Installing
2-3
Please read this section thoroughly before using and observe the mentioned safety
warnings fully.
Safety warnings are categorized as "Warning" or "Caution".
Warning
2-1
-- In case of mounting the temperature controllers to DIN rails, remember to push up
the locking tabs to fasten the controllers onto DIN rail.
-- To connect controllers, first release all locking tabs. Then, connect controllers and
push up all locking tabs. Make sure that all locking tabs are fastened.
-- Never fail to turn the power OFF, before detaching the terminal block or removing the
main unit from the base part.
-- In order to aid heat dissipation, do not block the top and the bottom of the equipment.
-- When mounting / dismounting controllers to / from DIN rails, 30mm of clearance
above and under the controllers should be provided.
INPTN5A0201-E
Improper use of the equipment may result in death or serious injuries.
Caution
2-2
Material No.
Caution
2
Please avoid installing in the following locations.
-- Locations in which the ambient temperature falls outside the range of 0 to 50 degrees
C when equipment is in use.
-- Locations in which the ambient humidity falls outside the range of 45 to 85% RH
when equipment is in use.
-- Locations with rapid temperature changes, leading to dew condensation.
-- Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable
gases.
-- Locations with vibration or shock directly.
-- Locations in contact with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, there is a risk of electric shock or fire, so have it
inspected by Fuji distributor.)
-- Locations with high concentrations of atmospheric dust, salt or iron particles.
-- Locations with large inductive interference, resulting in static electricity, magnetic
fields or noise.
-- Locations in direct sunlight.
-- Locations that build up heat from radiant heat sources, etc.
CAUTION
Before using the product, confirm that it
matches the type ordered.
(For model code, please refer to page 4.)
Confirm that all of the following
accessories are included.
Maintenance
Error Operation
-- The alarm function does not work properly when an error occurs unless the settings
are made correctly. Always verify its setting before operation.
DI1-4
2-5
DI5-8
DO1-4
Others
-- Please do not wipe the equipment with organic solvents such as alcohol or benzene,
etc. If wiping is necessary, use a neutral cleaning agent.
-- Do not use mobile phones near this equipment (within 50cm). Otherwise a
malfunction may result.
-- Malfunctions may occur if the equipment is used near a radio, TV, or wireless device.
-- This equipment requires approx. 20 seconds before it starts to output.
-- Before installing and wiring, take necessary measures for electrostatic discharge
(ESD).
DO5-8
Functional insulation (1000Vac)
Functional insulation (500Vac)
-- In cases where damage or problems with this equipment may lead to serious
accidents, install appropriate external protective circuits.
-- To prevent damage and failure of the equipment, provide the rated power voltage.
-- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is complete.
-- Before turning the power ON, confirm that clearance space has been secured to
prevent shock or fire.
-- Do not touch the terminal while the machine is ON. Doing so risks shock or
equipment errors.
-- Never disassemble, convert, modify or repair this equipment. Doing so risks abnormal
operation, shock or fire.
-1-
Part names and functions
Mounting
--Event input/output module controller
--Dimensions
DIO indicator
Front screw terminal cover
(optional)
PUM-E
LOADER
Terminal block
(when detached from the main unit)
Loader communication port
F012
STATION
345
7 8 9A
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
6
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
COM
BCD
PWR
LED indicator
Station No.
Configuration switch
See [Setting]
30
(10)
Base part
(when detached from
the main unit)
85
PUM-A
PWR
LOADER
COM
OUT1
OUT2
STATION
OUT3
6
100
1.5
OUT4
50
Input/output
terminals
See [Wiring]
RED
ORANGE
RUN
Error
-
COM
RS-485 receiving
-
RS-485 transmitting
Di1- 8
Digital inputting
Do1- 8
Digital outputting
Terminal
Screw size M3
(30)
(8)
GREEN
PWR
5
LED
DIN rail
Terminal
Screw size M3
6.1
LED indicator
LED lamps indicate the following operational conditions.
When locking tab is released
(when mounting /
dismounting to / from DIN rails)
Main unit
(when detached from the base part)
[mm]
Cautions when mounting
In order to aid heat dissipation, 30mm of clearance (50mm recommended) above and
under the controllers should be provided.
-- Actions to be displayed for COM, Di1-8 and Do1-8 can be allocated by programming.
30 or more
--Base part
Mounting screw hole
Module connector
(Connect controllers
laterally)
Module connector
Power terminal block
See [Wiring]
Mounting screw hole
See [Mounting]
30 or more
RS-485 terminal block
See [Wiring]
Locking tab
[mm]
--Mounting to DIN rails
Setting
--Setting Station No.
Set Station No. of each controller before mounting.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
29
D
30
E
31
F
32
--Attaching end plates
-- Each of connected controllers must have a different Station No. from other
controllers. Duplicate Station No. may cause malfunction of the equipment.
When mounting controllers to DIN rails, we recommend to attach side connecting
terminal covers (right and left 1set), then end plates (optional) to the ends of the
rightmost and leftmost controllers.
DIN rail mounting
end plate
PWR
PUM-A
PWR
LOADER
COM
COM
OUT1
OUT2
PUM-E
PWR
LOADER
COM
STATION
PUM-E
PWR
LOADER
COM
STATION
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
PWR
LOADER
COM
STATION
345
Side connecting terminal cover
(right & left 1 set)
-2-
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
LOADER
STATION
345
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
7 8 9A
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
6
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
7 8 9A
OUT4
STATION
6
OUT3
F012
28
C
E
27
B
F012
A
Station No.
setting switch
E
26
345
F012
9
STATION
E
25
3. Push up the locking tab to fasten
the controller onto DIN rail.
4. When connecting controllers
after mounting to DIN rail, push
up the locking tab after doing so.
LOADER
F012
8
PUM-E
E
24
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
F012
7
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
23
COM
F012
6
PWR
E
22
BCD
21
5
BCD
4
Locking tab
BCD
20
BCD
19
3
DIN rail
BCD
18
2
BCD
17
1
789A
Station No.
0
6
Rotary SW setting
Hook the back
of controller
1. Pull down the locking tab of the
base part. Hook the back of the
controller onto the upper part of
DIN rail.
2. Push the controller in the
direction of arrow 2.
DIN rail mounting
end plate
Wiring
--Fixing with screws
When mounting controllers inside a cabinet with screws, connect the base parts of
controllers first.
-- Fixing screws are not included. Please prepare screws as required.
1. Refer to the figure below for the mounting screw hole
(30)
size to decide the mounting position.
2-M3
9±0.2
--Front terminal block
[mm]
3. Connect base parts. Push up to fasten all the locking tabs.
4. Fixate the base parts onto the mounting position inside the cabinet with screws.
5. Attach the main unit to the base parts.
F012
11 COM
11
L
12
Do1
L
13
Do2
22
12
L
14
Do3
23
13
L
15
Do4
24
14
25
15
26
16
27
17
28
18
29
19
30
20
Transisitor
open collector
(sink) output
L
Di4
F01
3456
LOADER
Di2
STATION
345
8 9A
67
2
PUM-E
F012
STATION
789
BCDE
OUT4
A
OUT2
OUT3
2. Connect controllers with each other using
side connectors.
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
E
OUT1
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
21
Di1
Di8
Di7
Side
connector
Di6
Locking tab
Di5
STATION
345
L
18
Do6
L
19
Do7
L
20
Do8
OUT1
OUT2
OUT4
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do6
Do7
Do8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
15
16
17
18
19
20
PUM-E
LOADER
STATION
345
23
21
24
22
12
25
23
13
24
14
25
15
26
16
27
17
28
18
29
19
30
20
11
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
26
27
28
29
30
PUM-E
LOADER
DC 24V
STATION
345
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
F012
COM
E
PWR
LOADER
7 8 9A
E
PUM-E
Do5
14
6
345
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
6
F012
STATION
7 8 9A
BCD
OUT4
6
OUT3
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
F012
COM
E
PWR
LOADER
BCD
PUM-A
COM
OUT2
BCD
PWR
OUT1
COM
Do5
17
OUT3
22
DC 24V
3. After mounting controllers onto DIN rail,
make sure to push up all locking tabs.
Controllers are fastened to DIN rail and to
each other.
Relay
contact
output
13
BCD
COM
Do4
12
7 8 9A
PWR
LOADER
Do3
11
6
Di3
PUM-A
COM
Do2
16 COM
COM
PWR
Do1
DC 24V
PWR
--Connecting controllers
1. Check that locking tabs are pulled down
(released).
COM
345
F012
+0.2
30+0.7
Relay
contact
output
DC 24V
E
(100)
88.5 ±0.2
STATION
21
(3)
2. Remove the main unit from the base part.
See [How to detach the base part]
Transisitor
open collector
(sink) output
LOADER
7 8 9A
OUT4
PUM-E
6
OUT3
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
E
OUT2
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
BCD
COM
BCD
PWR
OUT1
--Base part (power terminal, RS-485 terminal)
4. All connected controllers are connected
to power supply and RS-485 via side
connectors if one of controllers is directly
connected to them.
Power terminal
RS-485 terminal
DC 24V (-)
DC 24V (+)
B (-)
A (+)
*All connected controllers are connected to power supply and RS-485 via side connectors
if one of controllers is directly connected to them.
How to detach the base part
1. Press the lock lever on the top of the
main unit.
Lock lever
2. Pull down the upper part of main unit.
3. Detach the cutout on the lower end of
back of main unit from the projection
on the base part.
-- When attaching the main unit to the
base part, take the reverse procedure
to removing the main unit from the
base part.
-- Make sure that the lock lever of the
main unit is fitted into the base part.
Projection
Main unit
-3-
SG
Specification
Model code
General Specification
Power Supply
Power Consumption
Dimensions
Weight
Installation method
Ambient temperature*
Ambient humidity
Event Input/Output module
: 24Vdc±10%
: Maximum 3.2W (135mA) [when 24Vdc is applied]
: 30(W)×100(H)×85(D) mm (excluding terminal cover and projection)
: Approx. 200g
: DIN rail mounting or mounting with M3 screws inside a cabinet
: -10 to 50 degrees C
* "Ambient temperature" is the temperature underneath the controller
inside the equipment or the cabinet where the controller is installed.
: 90% RH or less (non condensing)
1
2
3
4
5
6
P U M
7
8
9 10
Y Y 1 - 0
Description
Module type
Event input/output module
[Di 8 points/Do 8 points]
E
C
R
Digital input
A
B
No. of input
: 8 points (4 points / common × 2 blocks)
Input type
: Voltage contact input, sink / source common (bidirectional)
Input rating
: 24Vdc, Input impedance approx.4.7k ohm
Input judgment
: ON judgment
: 16 to 26.4Vdc
: OFF judgment
: 0 to 5Vdc
Input read cycle (min. pulse width):200ms
Output type (Event input/output module)
Open collector output
Relay contact output
Instruction manual
Japanese
English
Accessories (optional)
1
2
3
4
5
P U M Z *
Digital output
No. of output
: 8 points (4 points / common x 2 blocks)
Output type, rating
: Select from a) and b) according to the model specification
a) Relay contact output
- Contact structure : SPST contact
- Contact capacity : 220Vac / 30Vdc, 1A
b) Transistor open collector (sink output)
- Rating
: 24Vdc, 100mA (residual voltage when ON : 1.5Vdc or less)
6
7
8
A
A
A
A
L
0
0
0
0
0
1
2
3
4
1
Description
RS-485 terminating resistance
DIN rail mounting end plate
Side connecting terminal cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS-232C)
Communication function
RS-485 interface
Communication standard
: RS-485
No. of ports
: 1 port
Communication, synchro method : Two-wire, half-duplex, asynchronous cycle
Communication speed
: 9.6k, 19.2k, 38.4k, 115.2kbps
Data form
: data bit ; 8, parity ; even / odd / none
Communication distance
: 1km (38.4kbps or less), 250m (115.2kbps)
Connectable units
: 33 units (both master and slave units included)
(32 units if any modules other than PUM series is included in slaves)
Protocol
: Modbus RTU compatible
Loader (RS-232C) interface
Communication standard
: RS-232C
No. of ports
: 1 port
Communication, synchro method : Half-duplex, asynchronous cycle
Communication speed
: 19.2 kbps (fixed)
Data form
: data bit 8, no parity
Protocol
: Modbus RTU compatible
Crimp terminal size
Please prepare power cables and crimp terminals of the size indicated below.
Power cable
Cable type
Size
Thermocouple (Compensation lead wire)
Power supply
1.25mm2 or less
1.25mm2 or less
Crimp terminal
3.2mm
Ring crimp terminal
3.2mm
0.8Nm
6.0mm or less
Screw tightening torque
0.25 to 1.25mm2
6.0mm or less
Cable size
Y crimp terminal
International Sales Div
Sales Group
Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome,
Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fujielectric.com
Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425
http://www.fujielectric.com/products/instruments/
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement