D-Link DIR-130 - Broadband VPN Router Specifications

D-Link DIR-130 - Broadband VPN Router Specifications
Table of Contents
Manual Overview
This manual contains the following sections:
Section 1 - “Product Overview” describes what is included with the DIR-130 router, and things to consider
before installing (page 1).
Section 2 - “Installation” describes how to install the router on your network (page 6).
Section 3 - “Configuration” describes how to configure the settings on your DIR-130 router (page 10).
Section 4 - “Troubleshooting” explains how to resolve common issues (page 56).
Section 5 - “Appendix” contains networking basics, technical specifications, technical support information,
warranty, GNU general public license, and registration information (page 60).
D-Link DIR-130 User Manual
Table of Contents
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to
notify any person or organization of such revisions or changes.
Manual Revisions
Revision
Date
Description
1.0
February 8, 2007
• DIR-130 Revision A1 with firmware version 1.00
1.1
September 5, 2007
• Updated for firmware version 1.10
• Added Windows Vista™ support
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the
United States or other countries. All other company or product names mentioned herein are trademarks or registered
trademarks of their respective companies.
Copyright © 2007 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
D-Link DIR-130 User Manual
ii
Table of Contents
Table of Contents
Manual Overview........................................................... i
Manual Revisions..................................................... ii
Trademarks............................................................... ii
Product Overview......................................................... 1
Package Contents.................................................... 1
System Requirements.............................................. 2
Features.................................................................... 3
Hardware Overview.................................................. 4
Connections........................................................ 4
LEDs................................................................... 5
Installation..................................................................... 6
Before you Begin...................................................... 6
Connect to Cable/DSL/Satellite Modem................... 7
Connect to Another Router....................................... 8
Configuration.............................................................. 10
Web-based Configuration Utility............................. 10
Setup Wizard.................................................... 11
Manual Configuration........................................ 16
Dynamic (Cable)........................................... 16
PPPoE (DSL)................................................ 17
PPTP............................................................. 18
L2TP.............................................................. 19
Big Pond (Australia)....................................... 20
Static (assigned by ISP)................................ 21
Russian PPPoE (DSL).................................. 22
D-Link DIR-130 User Manual
Russian PPTP............................................... 23
Network Settings............................................... 24
DHCP Server Settings.................................. 25
DHCP Reservation........................................ 26
VPN Settings.................................................... 27
IPSec Settings............................................... 28
PPTP/L2TP Settings..................................... 31
Port Forwarding................................................ 32
Application Rules.............................................. 33
MAC Filters....................................................... 34
Website Filters.................................................. 35
Firewall Settings................................................ 36
DMZ.............................................................. 36
Firewall Rules................................................ 37
Advanced Network Settings.............................. 38
UPnP............................................................. 38
WAN Ping Respond...................................... 38
WAN Port Speed........................................... 38
Routing............................................................. 39
Certificates........................................................ 40
User Groups..................................................... 41
Administrator Settings....................................... 42
Change Password......................................... 42
Remote Management.................................... 42
Time and Date.................................................. 43
System Settings................................................ 44
Update Firmware.............................................. 45
iii
Table of Contents
DDNS................................................................ 46
System Check................................................... 47
Schedules......................................................... 48
Log Settings...................................................... 49
Device Information............................................ 50
Log.................................................................... 51
Statistics........................................................... 52
Active Session.................................................. 53
LAN Clients....................................................... 54
Routing............................................................. 54
VPN.................................................................. 55
Help.................................................................. 55
Troubleshooting.......................................................... 56
Networking Basics..................................................... 60
Check your IP address........................................... 60
Statically Assign an IP address.............................. 61
Technical Specifications............................................ 63
Default Factory Settings............................................ 64
Contacting Technical Support................................... 65
Warranty...................................................................... 66
GNU/Linux GPL........................................................... 71
GNU General Public License.................................. 72
Registration................................................................. 78
D-Link DIR-130 User Manual
iv
Section 1 - Product Overview
Product
PackageOverview
Contents
D-Link DIR-130 8-port
VPN Router
Power Adapter
Ethernet Cable
CD-ROM
Note: Using a power supply with a different voltage rating than the one included with the DIR-130 will cause damage and void the warranty for this
product.
D-Link DIR-130 User Manual
Section 1 - Product Overview
System Requirements
Network Requirements
• An Ethernet-based Cable or DSL modem
• 10/100 Ethernet devices
Computer with the following:
• Windows®, Macintosh, or Linux-based operating
system
• An installed Ethernet adapter
Web-based Configuration
Utility Requirements
Browser Requirements:
• Internet Explorer 6.0 or higher
• Mozilla 1.7.12 or higher
• Firefox 1.5 or higher
• Safari 1.0 or higher (with Java 1.3.1 or higher)
• Flock 0.7.14 or higher
• Opera 6.0 or higher
Windows® Users: Make sure you have the latest version
of Java installed. Visit www.java.com to download the
latest version.
D-Link DIR-130 User Manual
Section 1 - Product Overview
Features
•Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Parental Controls - Easily applied content filtering based on MAC Address, URL, and/or
Domain Name.
• Filter Scheduling - These filters can be scheduled to be active on certain days or for a
duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The DIR-130 can pass through VPN sessions. It
supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-130
can securely access corporate networks.
• User-friendly Setup Wizard - Through the easy-to-use web-based user interface, the DIR-130 allows
you to control what information is accessible to those on the network, whether from the Internet or from
your company’s server. Configure your router to your specific settings within minutes.
D-Link DIR-130 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
LAN Ports (1-8)
Connect Ethernet devices such as
computers, switches, and hubs.
Reset
Pressing the Reset button restores the router to
its original factory default settings.
Internet Port
The auto MDI/MDIX Internet port is the
connection for the Ethernet cable to the cable
or DSL modem.
Power Receptor
Receptor for the supplied power
adapter.
D-Link DIR-130 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
Status LED
A blinking light indicates that the
DIR-130 is ready.
Power LED
A solid light indicates a proper
connection to the power supply.
D-Link DIR-130 User Manual
Local Network LEDs
A solid light indicates a connection to an
Ethernet-enabled computer on ports 1-8.
This LED blinks during data transmission.
Internet LED
A solid light indicates connection on
the Internet port. This LED blinks
during data transmission.
Section 2 - Installation
Installation
This section will walk you through the installation process.
Before you Begin
Please configure the router with the computer that was last connected directly to your modem. Also, you can only use
the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off
your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as
WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.
D-Link DIR-130 User Manual
Section 2 - Installation
Connect to Cable/DSL/Satellite Modem
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
Internet port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your
computer.
5. Turn on or plug in your modem. Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router
to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, Internet light, and the LAN light (the port that your computer is
plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable
connections are correct.
9. Refer to page 10 to configure your router.
D-Link DIR-130 User Manual
Section 2 - Installation
Connect to Another Router
If you are connecting the D-Link router to another router to use as a switch, you will have to do the following before
connecting the router to your network:
• Disable UPnP™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot
accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable.
Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the
Networking Basics section for more information. If you need to change the settings, write down your existing settings
before making any changes. In most cases, your computer should be set to receive an IP address automatically in
which case you will not have to do anything to your computer.
2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user
name to Admin and leave the password box empty. Click Log In to continue.
3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings
to continue.
4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save
Settings to continue.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to
save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the
browser and change your computer’s IP settings back to the original values as in Step 1.
D-Link DIR-130 User Manual
Section 2 - Installation
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug
anything into the Internet port of the D-Link router.
8. You may now use the other 7 LAN ports to connect other Ethernet devices and computers.
D-Link DIR-130 User Manual
Section 3 - Configuration
Configuration
This section will show you how to configure your new D-Link router using the web-based configuration utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
Enter admin as the User name field and enter the
password in the Password field. Leave the password
blank by default.
If you get a Page Cannot be Displayed error, please
refer to the Troubleshooting section for assistance.
D-Link DIR-130 User Manual
10
Section 3 - Configuration
Setup Wizard
You may click Setup Wizard to quickly configure your router.
If you want to enter your settings without running the wizard, click
Manual Configure and skip to page 16.
Click Launch Internet Connection Setup Wizard to begin.
D-Link DIR-130 User Manual
11
Section 3 - Configuration
Click Next to continue.
Create a new password and then click Next to continue.
Select your time zone from the drop-down menu and then click Next
to continue.
Select the type of Internet connection you use and then click Next
to continue.
D-Link DIR-130 User Manual
12
Section 3 - Configuration
If you selected Dynamic, you may need to enter the MAC address of the
computer that was last connected directly to your modem. If you are currently
using that computer, click Clone Your PC’s MAC Address and then click
Next to continue.
The Host Name is optional but may be required by some ISPs. The default
host name is the device name of the Router and may be changed.
If you selected PPPoE, enter your PPPoE username and password. Click
Next to continue.
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses.
Note: Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password. Click Next
to continue.
D-Link DIR-130 User Manual
13
Section 3 - Configuration
If you selected L2TP, enter your L2TP username and password. Click Next
to continue.
If you selected Static, enter your network settings supplied by your Internet
provider. Click Next to continue.
If you selected Big Pond, select your authentication server from the drop
down menu. You will also need to enter your Big Pond username and
password. Click Next to continue.
D-Link DIR-130 User Manual
14
Section 3 - Configuration
If you selected Russian PPPoE, enter your PPPoE username and password.
Click Next to continue.
Select Static if your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses.
Note: Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
If you selected Russian PPTP, enter your PPTP username and password.
Click Next to continue.
Click Connect to save your settings. Once the router is finished rebooting,
click Continue. Please allow 1-2 minutes to connect.
Close your browser window and reopen it to test your Internet connection.
It may take a few tries to initially connect to the Internet.
D-Link DIR-130 User Manual
15
Section 3 - Configuration
Manual Configuration
Dynamic (Cable)
My Internet Select Dynamic IP (DHCP) to obtain IP Address
Connection: information automatically from your ISP. Select
this option if your ISP does not give you any IP
numbers to use. This option is commonly used
for Cable modem services.
Host Name: The Host Name is optional but may be required
by some ISPs.
MAC Address: The default MAC Address is set to the Internet
port’s physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP. You can use the Clone
Your PC’s MAC Address button to replace
the Internet port’s MAC address with the MAC
address of your Ethernet card.
DNS Addresses: Enter the Primary and Secondary DNS server
IP address(es) assigned by your ISP.
MTU: Maximum Transmission Unit - you may need to
change the MTU for optimal performance with
your specific ISP. 1500 is the default MTU.
D-Link DIR-130 User Manual
16
Section 3 - Configuration
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
My Internet Select PPPoE (Username/Password) from the drop-down menu.
Connection:
Address Mode: Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password and then retype the password in the next
box.
Service Name: Enter the ISP Service Name (optional).
IP Address: Enter the IP address (Static PPPoE only).
MAC Address: The default MAC Address is set to the Internet port’s physical interface
MAC address on the Broadband Router. It is not recommended that you
change the default MAC address unless required by your ISP. You can
use the Clone MAC Address button to replace the Internet port’s MAC
address with the MAC address of your Ethernet card.
DNS Addresses: Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
Maximum Idle Time: Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is
the default MTU.
Connect Mode: Select either Always-on, On-Demand, or Manual.
D-Link DIR-130 User Manual
17
Section 3 - Configuration
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
Address Mode: Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
IP Address: Enter the IP address (Static PPTP only).
Subnet Mask: Enter the Primary and Secondary DNS Server Addresses (Static
PPTP only).
Gateway: Enter the Gateway IP Address provided by your ISP.
DNS: The DNS server information will be supplied by your ISP (Internet
Service Provider.)
Server IP/Name: Enter the Server IP provided by your ISP (optional).
PPTP Account: Enter your PPTP account (username).
PPTP Password: Enter your PPTP password and then retype the password in the
next box.
Maximum Idle Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Time: Auto-reconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1450 is the
default MTU.
Connect Mode: Select either Always-on, On-Demand, or Manual.
D-Link DIR-130 User Manual
18
Section 3 - Configuration
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Address Mode: Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases,
select Dynamic.
IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
Subnet Mask: Enter the Subnet Mask supplied by your ISP (Static only).
Gateway: Enter the Gateway IP Address provided by your ISP.
DNS: Enter the Primary and Secondary DNS Server Addresses (Static
L2TP only).
Server IP/Name: Enter the Server IP provided by your ISP (optional).
L2TP Account: Enter your L2TP account (username).
L2TP Password: Enter your L2TP password and then retype the password in the
next box.
Maximum Idle Time: Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1450 is
the default MTU.
Connect Mode: Select either Always-on, On-Demand, or Manual.
D-Link DIR-130 User Manual
19
Section 3 - Configuration
Internet Setup
Big Pond (Australia)
My Internet Select BigPond (Australia) from the drop-down
Connection: menu.
Username: Enter your BigPond username.
Password: Enter your BigPond password and then retype
the password in the next box.
Auth Server: Select the type of authentication server being
used from the drop-down menu.
Login Server IP: Enter the IP address of the login server.
MAC Address: The default MAC Address is set to the
Internet’s physical interface MAC address on
the Broadband Router. It is not recommended
that you change the default MAC address
unless required by your ISP. You can use the
Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with
the MAC address of your Ethernet card.
D-Link DIR-130 User Manual
20
Section 3 - Configuration
Internet Setup
Static (assigned by ISP)
Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address,
subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the
appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.
IP Address: Enter the IP address assigned by your ISP.
Subnet Mask: Enter the Subnet Mask assigned by your ISP.
ISP Gateway: Enter the Gateway assigned by your ISP.
MAC Address: The default MAC Address is set to the Internet port’s
physical interface MAC address on the Broadband
Router. It is not recommended that you change the
default MAC address unless required by your ISP.
You can use the Clone MAC Address button to
replace the Internet port’s MAC address with the
MAC address of your Ethernet card.
DNS Servers: The DNS server information will be supplied by your
ISP (Internet Service Provider.)
MTU: Maximum Transmission Unit - you may need to
change the MTU for optimal performance with your
specific ISP. 1500 is the default MTU.
D-Link DIR-130 User Manual
21
Section 3 - Configuration
Internet Setup
Russian PPPoE (DSL)
Choose Russian PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer.
The software is no longer needed and will not work through a router.
Address Mode: Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password and then retype the password in the next
box.
Service Name: Enter the ISP Service Name (optional).
IP Address: Enter the IP address (Static PPPoE only).
MAC Address: The default MAC Address is set to the Internet port’s physical interface
MAC address on the Broadband Router. It is not recommended that you
change the default MAC address unless required by your ISP. You can
use the Clone MAC Address button to replace the Internet port’s MAC
address with the MAC address of your Ethernet card.
Maximum Idle Time: Enter a maximum idle time during which the Internet connection is
maintained during inactivity. To disable this feature, enable Autoreconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your specific ISP. 1492 is the default MTU.
Connect Mode: Select either Always-on, On-Demand, or Manual.
WAN Physical In most cases, select Dynamic PPPoE. Select Static PPPoE if your ISP assigned you the IP address, subnet mask, gateway,
Setting: and DNS server addresses.
DNS Addresses: Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
D-Link DIR-130 User Manual
22
Section 3 - Configuration
Internet Setup
Russian PPTP
Choose Russian PPTP (Point-to-Point-Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Address Mode: Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
Server IP/Name: Enter the Server IP provided with your ISP.
PPTP Account: Enter your PPTP account (username).
PPTP Password: Enter your PPTP password and then retype the password in the
next box.
Maximum Idle Enter a maximum idle time during which the Internet connection
Time: is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU: Maximum Transmission Unit - you may need to change the MTU
for optimal performance with your specific ISP.
Connect Mode: Select either Always-on, On-Demand, or Manual.
WAN Physical Select Static IP if your ISP assigned you the IP address, subnet
Setting: mask, gateway, and DNS server addresses.
IP Address: Enter the Server IP provided by your ISP (optional).
Subnet Mask: Enter the Subnet Mask supplied by your ISP (Static IP only).
Gateway: Enter the Gateway Address provided by your ISP (Static IP only)
Clone MAC Setting: Click the Clone MAC Address button to copy the MAC Address from your PC.
DNS Setting: Enter the Primary and Secondary DNS Server Addresses (Static IP only).
D-Link DIR-130 User Manual
23
Section 3 - Configuration
Network Settings
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Router IP Address: Enter the IP address of the router. The default IP
address is 192.168.0.1.
If you change the IP address, once you click Apply,
you will need to enter the new IP address in your
browser to get back into the configuration utility.
Default Subnet Enter the Subnet Mask. The default subnet mask is
Mask: 255.255.255.0.
Local Domain Name: Enter the Domain name (optional).
Enable DNS Relay: Uncheck the box to transfer the DNS server
information from your ISP to your computers. If
checked, your computers will use the router for a
DNS server.
D-Link DIR-130 User Manual
24
Section 3 - Configuration
DHCP Server Settings
The router has a built-in DHCP (Dynamic Host Control Protocol) server. The DHCP Server will automatically assign an
IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting
their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically
load the proper TCP/IP settings provided by the router. The DHCP Server will automatically allocate an unused IP
address from the IP address pool to the requesting computer. You must specify the starting and ending address of the
IP address pool.
Enable DHCP Check this box to enable the DHCP server on
Server: your router. Uncheck to disable this function.
DHCP IP Address Enter the starting and ending IP addresses for
Range: the DHCP server’s IP assignment.
Note: If you statically (manually) assign IP
addresses to your computers or devices, make
sure the IP addresses are outside of this range
or you may have an IP conflict.
DHCP Lease The length of time for the IP address lease.
Time: Enter the Lease time in minutes.
D-Link DIR-130 User Manual
25
Section 3 - Configuration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation.
The router will assign the IP address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
DHCP Check the box under the first column to enable
Reservations List: the reservation.
Computer Name: Enter the computer name or select from the
drop-down menu (last column) and click <<.
IP Address: Enter the IP address you want to assign to the
computer or device. This IP Address must be
within the DHCP IP Address Range.
MAC Address: Enter the MAC address of the computer or
device.
Copy Your PC’s If you want to assign an IP address to the
MAC Address: computer you are currently on, click this button
to populate the fields.
Save: Click Save to save your entry. You must click
Save Settings at the top to activate your
reservations.
D-Link DIR-130 User Manual
26
Section 3 - Configuration
VPN Settings
The DIR-130 supports IPSec, PPTP, and L2TP VPN as the Server Endpoint.
Add VPN Profile: Select IPSec or PPTP/L2TP from the drop-down
menu and then click Add.
D-Link DIR-130 User Manual
27
Section 3 - Configuration
IPSec Settings
Enable: Check this box to enable IPSec.
Name: Enter a name for your VPN.
Local Net/ Mask: Enter the local (LAN) subnet and mask.
(ex. 192.168.0.0/24)
Remote IP: Select Site to Site or Remote User for the
required VPN configuration.
•Site to Site - Network-to-network VPN in
which two entire LAN networks are virtually
connected across the Internet. If selected,
enter the destination gateway IP address in
the box which is the public WAN IP or host
address of the remote VPN server endpoint.
•Remote User – Client-to-server VPN in
which remote VPN clients can to connect to
the router from the Internet and access Local
Network resources.
Remote Local If Site to Site is selected, enter the Destination
LAN Net/ Mask: subnet and mask of the remote network.
(ex. 192.168.1.0/24)
Authentication: Select Pre-shared Key or X.509 Certificate Authentication. One of these two authentication methods must be selected.
•Pre-shared Key - Manually enter ASCII passphrase in box.
•X.509 Certificate - For certificate authentication, certificates must be manually uploaded to the router. See the “Certificates”
section for details.
D-Link DIR-130 User Manual
28
Section 3 - Configuration
• Additional Authentication Methods (Optional)
XAUTH - Check this box to include additional username and password authentication requirements for the VPN.
Select Server Mode or Client Mode.
•Server Mode - Select a group from the Authentication database drop-down menu containing the list
of user credentials permitted.
•Client Mode - Enter the user name and password if required by the remote VPN server endpoint
configured in xAuth Server Mode.
Local/Remote ID - Check this box to include additional ID authentication requirements for the VPN using a specific
IP Address, FQDN, ASN1, or a Custom String.
•Local ID - Select one of the options from the drop-down menu. Enter an ID to identify and authenticate
the local VPN endpoint.
•Remote ID - Select one of the options from the drop-down menu. Enter an ID to identify and authenticate
the remote VPN endpoint.
Main / Aggressive Mode: Select Main Mode or Aggressive Mode for IKE Phase 1 negotiation.
•Main Mode - Select this option to configure the standard negotiation parameters for IKE Phase 1 of
the VPN Tunnel. (Recommended Setting)
•Aggressive Mode - Select this option to configure IKE Phase 1 of the VPN Tunnel to carry out
negotiation in a shorter amount of time. (Not Recommended - Less Secure)
NAT-T Enable: Check this box to enable NAT Traversal. Enabling this option will allow IPSec traffic from this endpoint to traverse
through the translation process during NAT. The remote VPN endpoint must also support this feature and it must
be enabled to function properly over the VPN.
D-Link DIR-130 User Manual
29
Section 3 - Configuration
Keep Alive / DPD: Select None, Keep Alive, or DPD (Dead Peer
Connection).
•None - Select this option to disable Keep Alive.
•Keep Alive - Select this option to send random ping
requests from this endpoint to the remote endpoint
keeping the tunnel established during long idle
periods of inactivity.
•DPD - Select this option to delete the VPN tunnel if
there is no traffic detected. The VPN will re-establish
once traffic is again sent through the tunnel.
DH Group: Select a DH Group from the drop-down menu. As the DH
Group number increases, the higher the level of encryption
implemented for Phase 1.
IKE Proposal List: Select the Cipher and Hash from the drop-down menus.
The proposal listing is evaluated in order with #1 being the
first proposal to attempt in IKE negotiation.
IKE Lifetime: Enter the number of seconds for the IKE Lifetime. The period of time to pass before establishing a new IKE security
association (SA) with the remote endpoint. The default value is 28800.
PFS Enable: Check to enable or uncheck to disable. PFS is an additional security protocol.
PFS DH Group: Select a PFS DH Group from the drop-down menu. As the DH Group number increases, the higher the level of
encryption implemented for PFS.
IPSec Proposal List: Select the Cipher and Hash from the drop-down menus. The proposal listing is evaluated in order with #1 being
the first proposal to attempt in IPSec negotiation.
IPSec Lifetime: Enter the number of seconds for the IPSec Lifetime. The period of time to pass before establishing a new IPSec
security association (SA) with the remote endpoint. The default value is 3600.
D-Link DIR-130 User Manual
30
Section 3 - Configuration
PPTP/L2TP Settings
PPTP uses TCP port 1723 for its control connection and uses GRE (IP protocol 47) for the PPP data. PPTP supports
data encryption by used MPPE.
L2TP uses UDP protocol to transport the PPP data. This is often encapsulated in IPSec encryption instead of
MPPE.
Enable Setting: Check this box to enable.
Name: Enter a name for your VPN.
Connection Type: Select PPTP, L2TP, or L2TP over IPSec.
VPN Server IP: Enter the VPN Server IP address which is the
LAN IP of the router. (i.e. 192.168.0.1).
Remote IP Range: Assign a range of IP addresses. The assigned
IP range should be on the same IP network
but not the in the same range as your DHCP
IP range.
For example, if your network is 192.168.0.xxx
and you set the DHCP range to 192.168.0.100200, the remote IP range cannot be within
192.168.0.100-200.
Authentication Select the desired authentication protocol (PAP/CHAP/MS-CHAP v2).
Protocol:
MPPE Encryption Select the level of encryption (None/40-bit/128-bit).
Mode:
Authentication Select a user group from the drop-down menu. You can create user groups in the Advanced > User Group section.
Database:
D-Link DIR-130 User Manual
31
Section 3 - Configuration
Port Forwarding
This section allows you to open a single port or a range of ports.
Name: Enter a name for the rule or select an application
from the drop-down menu. Select an application
and click << to populate the fields.
IP Address: Enter the IP address of the computer on your local
network that you want to allow the incoming service
to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer
will be listed in the “Computer Name” drop-down
menu. Select your computer and click <<.
Port: Enter a port or port range for the public and private
port.
Traffic Type: Select the type of protocol you would like to assign
to the rule.
Schedule: The schedule of time when the Virtual Server Rule
will be enabled. The schedule may be set to Always,
which will allow the particular service to always
be enabled. You can create your own times in the
Maintenance > Schedules section.
D-Link DIR-130 User Manual
32
Section 3 - Configuration
Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and
others. These applications have difficulties working through NAT (Network Address Translation). Special Applications
makes some of these applications work with the DIR-130. If you need to run applications that require multiple connections,
specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or
UDP, then enter the firewall (public) ports associated with the trigger port to open them for inbound traffic.
Name: Enter a name for the rule. You may select a
pre-defined application from the drop-down
menu and click <<.
Trigger: This is the port used to trigger the application. It
can be either a single port or a range of ports.
Firewall: This is the port number on the Internet side
that will be used to access the application. You
may define a single port or a range of ports.
You can use a comma to add multiple ports or
port ranges.
Traffic Type: Select the protocol of the firewall port (TCP,
UDP, or Any).
Schedule: The schedule of time when the Application Rule
will be enabled. The schedule may be set to
Always, which will allow the particular service
to always be enabled. You can create your
own times in the Maintenance > Schedules
section.
D-Link DIR-130 User Manual
33
Section 3 - Configuration
MAC Filters
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses
from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of
clients that are currently connected to the router. You may enter up to 25 rules.
Configure MAC Select Turn MAC Filtering Off, Turn MAC
Filtering: filtering on and ALLOW computers listed to
access the network, or Turn MAC filtering on
and DENY computers listed to access the
network from the drop-down menu.
MAC Address: Enter the MAC address you would like to filter.
To find the MAC address on a computer, please
refer to the Networking Basics section in this
manual.
DHCP Client: Select a DHCP client from the drop-down menu
and click << to copy that MAC Address.
Clear: Click to delete the settings of the filter rule.
D-Link DIR-130 User Manual
34
Section 3 - Configuration
Website Filters
Website Filters are used to deny LAN computers from accessing specific web sites by the URL or domain. A URL is a
specially formatted text string that defines a location on the Internet. If any part of the URL contains the blocked word,
the site will not be accessible and the web page will not display. To use this feature, enter the text string to be blocked
and click Save Settings. The text to be blocked will appear in the list. To delete the text, click the Clear the List Below
button.
Configure Website Select Turn Website Filtering Off, Turn
Filtering: Website filtering on and ALLOW computers
listed to access the network, or Turn Website
filtering on and DENY computers listed
to access the network from the drop-down
menu.
Website URL/ Enter the keywords or URLs that you want to
Domain: block (or allow). Any URL with the keyword in it
will be blocked or allowed.
Schedule: The schedule of time when the selected rule
will be enabled. The schedule may be set to
Always, which will allow the filter to always be
enabled. You can create your own times in the
Maintenance > Schedules section.
D-Link DIR-130 User Manual
35
Section 3 - Configuration
Firewall Settings
DMZ
A firewall protects your network from the outside work. The D-Link DIR-130 offers a firewall protection such as SPI
(Stateful Packet Inspection) and NAT/PAT (Network Address Translation/Port Address Translation). Sometimes you may
want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you
can enable DMZ (Demilitarized Zone). This option will expose the chose computer completely to the outside world.
Enable DMZ Host: If an application has trouble working from
behind the router, you can expose one
computer to the Internet and run the application
on that computer.
Note: Placing a computer in the DMZ may
expose that computer to a variety of security
risks. This option is only recommended as a
last resort.
DMZ IP Address: Specify the IP address of the computer on the
LAN that you want to have unrestricted Internet
communication. If this computer obtains its IP
address automatically using DHCP, be sure
to make a static reservation on the Internet >
DHCP page so that the IP address of the DMZ
machine does not change.
Schedule: The schedule of time when the DMZ will
be enabled. The schedule may be set to
Always, which will allow the DMZ to always be
enabled. You can create your own times in the
Maintenance > Schedules section.
D-Link DIR-130 User Manual
36
Section 3 - Configuration
Firewall Settings
Firewall Rules
Up to 75 Firewall Rules can be created to control the incoming and outgoing traffic on your router. For each rule you
can create a name and control the direction of traffic. You can also allow or deny a range of IP Addresses, protocol and
a port range. In order to apply a schedule to a Firewall Rule, you must first define a schedule on the Maintenance >
Schedules page. The first 2 Firewall Rules are default and cannot be changed.
Name: Enter a name for your Firewall Rule.
Schedule: Select a schedule from the drop-down menu. In
order to apply a schedule to a Firewall Rule, you
must first define a schedule on the Maintenance >
Schedules page.
Source/Dest: This setting controls the direction of traffic. To control
incoming traffic, set the Source Interface to WAN
and the Dest Interface to LAN. To control outgoing
traffic, set the Source Interface to LAN and the Dest
Interface to WAN.
IP Address Range: Enter the IP Address Range for both the Source
Interface and Dest Interface. These IP Address
Ranges will be either allowed or denied, depending
on the selected action.
Protocol: Select a protocol from the drop-down menu. The
protocol that is selected will be either allowed or
denied, depending on the selected action.
Port Range: Enter a Port Range. The Port Range that is entered
will be either allowed, or denied, depending on the
selected action.
D-Link DIR-130 User Manual
37
Section 3 - Configuration
Advanced Network Settings
UPnP: Click on the checkbox to enable Universal Plug
and Play (UPnP™). UPnP provides compatibility
with networking equipment, software and
peripherals.
Enable WAN Ping Unchecking the box will not allow the DIR-130
Respond: to respond to pings. Blocking pings may provide
some extra security from hackers. Check the box
to allow the Internet port to be “pinged”.
WAN Port Speed: You may set the port speed of the Internet port to
10Mbps, 100Mbps, or Auto. Some older cable
or DSL modems may require you to set the port
speed to 10Mbps.
D-Link DIR-130 User Manual
38
Section 3 - Configuration
Routing
This section allows you to define static routes for the WAN types of Static IP, Dynamic IP, Russian PPPoE, and Russian
PPTP with ISPs that require these parameters. Up to 50 Static Routing Rules can be defined.
Interface: Select WAN or WAN_Physical from the drop
down menu. Only select WAN_Physical if your
Internet connection type is Russian PPPoE or
Russian PPTP.
Destination Enter the destination address for the static routing
Address: rule.
Subnet Mask: Enter the subnet mask for the static routing rule.
Gateway: Enter the gateway for the static routing rule.
Metric: Enter the metric for the static routing rule.
D-Link DIR-130 User Manual
39
Section 3 - Configuration
Certificates
This section is used to configure Certificates that are used with an IPSec based VPN. You can configure local certificates
and the certificates of remote peers. Select one of the three options from the drop-down menu: Local Certificate &
Private key, Certificate of Remote Peers, or Certificate Authorities.
Local Certificate Select this option from the drop-down menu to
& Private Key: configure your local certificates. Enter a name
for the certificate. Click the browse button to look
for the Private Key and the certificate on your
computer.
Certificate of Select this option from the drop-down menu to
Remote Peers: configure the certificates of remote peers. Enter
a name for the certificate. Click the browse button
on your computer to look the Private Key on your
computer.
Certificate Select this option from the drop-down menu to
Authorities: configure Certificate Authority (CA) files to be
used with your router. Enter a name for the CA
file. Click the browse button to look for the CA file
on your computer.
D-Link DIR-130 User Manual
40
Section 3 - Configuration
User Groups
This section is used to configure Certificates that are used with an IPSec based VPN. You can configure local certificates
and the certificates of remote peers. Select one of the three options from the drop-down menu: Local Certificate &
Private key, Certificate of Remote Peers, or Certificate Authorities.
Authentication Select a user group from the menu and click the
Database: EDIT button to configure that group.
Group Name: Enter a name for the user group. Click the Clear
the list below button to erase all of the user
names and passwords for the user group.
User Name: Enter the User Name.
Password: Enter the Password.
D-Link DIR-130 User Manual
41
Section 3 - Configuration
Administrator Settings
This page will allow you to change the Administrator password. You can also enable Remote Management.
Admin Password: Enter a new password for the administrator login.
Only the administrator can make changes to the
settings.
Enable Remote Remote management allows the router to be
Management: configured from the Internet by a web browser. A
username and password is still required to access
the Web-Management interface. In general, only a
member of your network can browse the built-in web
pages to perform Administrator tasks. This feature
enables you to perform Administrator tasks from
the remote (Internet) host.
IP Address: Enter the IP address of the remote computer. You
may enter * to allow a connection from any Internet
address.
Port: The port number used to access the DIR-130.
Example: http://x.x.x.x:8080 whereas x.x.x.x is the
Internet IP address of the DIR-130 and 8080 is the
port used for the Web Management interface. The
schedule may be set to Always, which will allow the
filter to always be enabled. You can create your own
times in the Maintenance > Schedules section.
D-Link DIR-130 User Manual
42
Section 3 - Configuration
Time and Date
The Time and Date page allows you to configure, update, and maintain the correct time and date on the internal system
clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also
be configure to automatically adjust the time when needed.
Time Zone: Select the Time Zone from the drop-down
menu.
Enable Daylight Check the checkbox to enable daylight savings
Saving: time.
Sync. Your Click this button to copy the time settings from
computer’s time your computer.
settings:
Automatic Check the box to use NTP (Network Time
Time and Date Protocol) server. NTP synchronizes computer
Configuration: clock times in a network of computers. This will
only connect to a server on the Internet, not a
local server.
NTP Server Used: Select an NTP server from the drop-down
menu.
Manual: To manually input the time, enter the values
in these fields for the Year, Month, Day, Hour,
Minute, and Second and then click Save
Settings.
D-Link DIR-130 User Manual
43
Section 3 - Configuration
System Settings
Save Settings to Use this option to save the current router
Local Hard Drive: configuration settings to a file on the hard disk
of the computer you are using. First, click the
Save Configuration button. You will then see a
file dialog, where you can select a location and
file name for the settings.
Load Settings Use this option to load previously saved
from Local Hard router configuration settings. First, click the
Drive: Browse button to find a previously save file of
configuration settings. Then, click the Restore
Configuration from File button to transfer
those settings to the router.
Restore to Factory This option will restore all configuration settings
Default Settings: back to the settings that were in effect at the
time the router was shipped from the factory.
Any settings that have not been saved will be
lost, including any rules that you have created. If
you want to save the current router configuration
settings, use the Save Configuration button
above.
Reboot the Click to reboot the router.
DIR-130:
D-Link DIR-130 User Manual
44
Section 3 - Configuration
Update Firmware
You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of
the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support
site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the
D-Link support site.
Browse: After you have downloaded the new firmware,
click Browse to locate the firmware update on
your hard drive. Click Apply to complete the
firmware upgrade.
D-Link DIR-130 User Manual
45
Section 3 - Configuration
DDNS
DDNS (Dynamic Domain Name System) is a method of keeping a domain name linked to a changing IP Address. The
DDNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers
assign dynamic IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect
to your server no matter what your IP address is.
DDNS: Check the box to enable DDNS.
Server Address: Choose your DDNS provider from the drop
down menu.
Host Name: Enter you Host Name that you registered with
your DDNS service provider.
Username or Key: Enter the Username or Key for your DDNS
account.
Password or Key: Enter the Password or Key for your DDNS
account.
Verify Password or Reenter the password or key for your DDNS
Key: account.
Timeout: The default value is 240 (hours). Do not change
this value unless otherwise specified by you
DDNS service provider.
D-Link DIR-130 User Manual
46
Section 3 - Configuration
System Check
The router System Check uses a ping test to send ping packets to test if a computer in on the Internet.
Ping Test: Enter the IP address that you wish to ping and
click the Ping button.
Ping Results: The results of your ping attempts will be
displayed here.
D-Link DIR-130 User Manual
47
Section 3 - Configuration
Schedules
This section is used to manage schedule rules for port forwarding, firewall rules, web filtering, and remote
Name: Enter a name for your new schedule.
Days: Select a day, a range of days, or All Week to
include every day.
Time: Check All Day - 24hrs or enter a start and
end time for your schedule.
Save: Click Save to save your schedule. You must
click Save Settings at the top for your
schedules to go into effect.
Schedule Rules The list of schedules will be listed here. Click
List: the Edit icon to make changes or click the
Delete icon to remove the schedule.
D-Link DIR-130 User Manual
48
Section 3 - Configuration
Log Settings
SMTP Server/IP The address of the SMTP server that will be
Address: used to send the logs.
Email Address: The email address to which the logs will be sent.
Click on Send Mail Now to send the email.
Save Log File to Click to save the log to your hard drive.
Local Hard Drive:
Log Type: Select the type of log you would like to view.
D-Link DIR-130 User Manual
49
Section 3 - Configuration
Device Information
This page displays the current information for the DIR-130. It will display the LAN, WAN (Internet), and the firmware
version of the router.
If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be
displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP.
If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use
Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.
LAN: Displays the MAC address and the private
(local) IP settings for the router.
WAN: Displays the MAC address and the public IP
settings for the router.
D-Link DIR-130 User Manual
50
Section 3 - Configuration
Log
This page displays the log events of the router. Here you can view the logs of the router.
First Page: This button will direct you to the current first page
of the log.
Last Page: This button will direct you to the current last page
of the log.
Previous: Click to view the previous page of the log.
Next: Click to view the next page of the log.
Clear: Clears all current log content.
D-Link DIR-130 User Manual
51
Section 3 - Configuration
Statistics
This page displays the current statistics of the router. Here you can view the amount of packets that pass through the
router.
Refresh: This button will refresh the statistics to display
updated information.
Reset: This button will reset the statistics packet
count to zero for all interfaces listed.
WAN: Displays the amount of packets transmitted
and received on the WAN interface.
LAN: Displays the amount of packets transmitted
and received on the LAN interface.
D-Link DIR-130 User Manual
52
Section 3 - Configuration
Active Session
The Active Session Status menu shows the active sessions currently running on your router. The list will display the
protocol, the source IP address and the destination IP address for each active session.
First Page: This button will direct you to the current first
page of the active sessions.
Last Page: This button will direct you to the current last
page of the active sessions.
Previous: This button will direct you to the previous page
of the active sessions.
Next: This button will direct you to the next page of
the active sessions.
D-Link DIR-130 User Manual
53
Section 3 - Configuration
LAN Clients
This page displays a list of currently connected wired clients. This table also displays the connection time and MAC
address of the connected wired clients.
Routing
This page displays a list of the default and static routes used by the router.
D-Link DIR-130 User Manual
54
Section 3 - Configuration
VPN
The VPN table displays a list of current PPTP, L2TP, L2TP over IPSec, and IPSec VPN sessions.
Help
The support menu provides additional information regarding features included in the DIR-130 Web Management
Interface.
D-Link DIR-130 User Manual
55
Section 4 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-130. Read
the following descriptions if you are having problems. (The examples below are illustrated in Windows® Vista™ and XP. If
you have a different operating system, the screenshots on your computer will look similar to the following examples.)
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on
the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself.
Your computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
• Internet Explorer 6.0 or higher
• Firefox 1.5 or higher
• Netscape 8 or higher
• Mozilla 1.7.12 (5.0) or higher
• Opera 8.5 or higher
• Safari 1.2 or higher (with Java 1.3.1 or higher)
• Camino 0.8.4 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using
a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may
not be on.
• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,
Sygate, Norton Personal Firewall, and Windows® firewall may block access to the configuration pages. Check the help
files included with your firewall software for more information on disabling or configuring it.
D-Link DIR-130 User Manual
56
Section 4 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Control Panel. In Windows® XP or Windows Vista™, make sure you are in Classic View.
Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to
their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings
button. Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three
times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address
bar. This should open the login page for your the web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait
about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different
computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back
to the factory defaults. You will lose all your custom settings.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a
paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process.
Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is
admin and leave the password box empty. A list of the default settings can be found on page 64.
D-Link DIR-130 User Manual
57
Section 4 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router?
If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and
Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
Note: AOL DSL+ users must use MTU of 1400.
To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could
be another computer, or a URL.
• Windows Vista™ users click on Start and type cmd in the Start Search box. Click OK or press Enter.
• Windows® NT, 2000 and XP users click on Start, click Run, and then type cmd in the box. Click OK or
press Enter.
• Windows® 95, 98, and Me users click on Start, click Run, and then type command. Click OK or press
Enter.
• Once the window opens, you’ll need to do a special ping.
Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
D-Link DIR-130 User Manual
58
Section 4 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a
fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example,
lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network
we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
•Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
•Enter your username (admin) and password (blank by default). Click OK to enter the web configuration
page for the device.
•Click on Setup and then click Manual Configure.
•To change the MTU enter the number in the MTU field and click Save Settings to save your settings.
•Test your e-mail. If changing the MTU does not resolve the problem, continue changing the MTU in
increments of ten.
4. Why is the date on the logs incorrect?
The router has not successfully connected to a Network Time (NTP) server. Check that your Internet connection settings
are correct. If you have connected for the first time, allow up to 10 minutes to connect.
If the time is off by 1 hour, make sure you have selected the correct time zone and that Daylight Savings is selected.
Refer to Section 3 - Configuration > Time and Date for more information.
D-Link DIR-130 User Manual
59
Appendix A - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter or if you already have an Ethernet adapter installed on your computer, by
default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. router) automatically. To
verify your IP address, please follow the steps below.
Windows Vista™ Users:
• Click Start > All Programs > Accessories > Command Prompt. You may
need administrative access to run this application.
• For all additional prompt windows inquiring of running the command prompt
application, select Yes, OK, or Continue.
• At the prompt, type ipconfig and press Enter.
• This will display the IP address, subnet mask, and default gateway of your
adapter.
Windows® 2000/XP Users:
• Click on Start > Run. In the run box type cmd and click OK.
• At the prompt, type ipconfig and press Enter.
• This will display the IP address, subnet mask, and the default gateway of your
adapter.
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs
may block a DHCP request on newly installed adapters.
D-Link DIR-130 User Manual
60
Appendix A - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps
below:
Windows® XP/2000 Users
• Windows® XP - Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network Connections
icon.
Windows® 2000 – From the desktop, right-click My Network Places > Properties.
• Right-click on the Local Area Connection which represents your D-Link network adapter (or other adapter) which will be connected
to your router.
• Highlight Internet Protocol (TCP/IP) and click Properties.
• Click Use the following IP address and enter an IP address that is on the same subnet as your network or LAN IP address on
your router.
Example: If the router’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not in
use on the network.
• Set Default Gateway the same as the LAN IP address of your router (192.168.0.1).
• Set Primary DNS the same as the LAN IP address of your router (192.168.0.1).
• The Secondary DNS is optional (you may enter a DNS server from your ISP).
• Click OK to save your settings.
D-Link DIR-130 User Manual
61
Appendix A - Networking Basics
Windows Vista™ Users
• Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network and Sharing Center icon. Along
the left panel in the window, click on Manage network connections.
• Right-click on the Local Area Connection which represents your D-Link network adapter (or other adapter) which will be connected
to your router.
• Highlight Internet Protocol Version 4 (TCP /IPv4) and click Properties.
• Click Use the following IP address and enter an IP address that is on the same subnet as your network or LAN IP address on
your router.
Example: If the router’s LAN IP address is 192.168.0.1, make your IP
address 192.168.0.X where X is a number between 2 and 99. Make sure
that the number you choose is not in use on the network.
• Set Default Gateway the same as the LAN IP address of your router
(192.168.0.1).
• Set Primary DNS the same as the LAN IP address of your router
(192.168.0.1).
• The Secondary DNS is optional (you may enter a DNS server from your
ISP).
• Click OK to save your settings.
D-Link DIR-130 User Manual
62
Appendix B - Technical Specifications
Technical Specifications
Standards
• IEEE 802.3
• IEEE 802.3u
LEDs
• Power • Status • WAN
• LAN (1-8)
Operating Temperature
• 32°F to 104°F ( 0°C to 40°C)
Humidity
• 95% maximum (non-condensing)
Safety & Emissions
• FCC
• CE
• IC
Dimensions
• L = 7.6 inches
• W = 4.6 inches
• H = 1.2inches
Warranty
• 1 Year
D-Link DIR-130 User Manual
63
Appendix B - Technical Specifications
Default Factory Settings
When you receive your router, the default factory settings are in effect as listed in the table below. You may change
any of the network settings. If you perform a reset (hold the reset button on the back of the unit), the router will reset
with the following settings:
D-Link DIR-130 User Manual
Setting
Default Value
Username
admin
Password
(leave blank)
LAN IP Address
192.168.0.1
DHCP Server
Enabled
DHCP IP Range
192.168.0.100 - 192.168.0.150
Filtering / Virtual Server / DMZ / Applications
Disabled
64
Appendix C - Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DIR-130)
• Hardware Revision (located on the label on the bottom of the router (e.g. rev A1))
• Serial Number (s/n number located on the label on the bottom of the router).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions
and answers to technical issues.
For customers within the United States:
For customers within Canada:
Phone Support:
(877) 354-6555
Internet Support:
http://support.dlink.com
Phone Support:
(877) 354-6560
Internet Support:
http://support.dlink.com
D-Link DIR-130 User Manual
65
Appendix D - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in
workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below
(“Warranty Period”), except as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the
actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement
hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part
thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects
to the defective Hardware. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety
(90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if
D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the
defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced
by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
D-Link DIR-130 User Manual
66
Appendix D - Warranty
Limited Software Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety
(90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated
in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the
Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under
this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially
conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable
to the Software. Except as otherwise agreed by DLink in writing, the replacement Software is provided only to the original licensee, and
is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the
remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable
of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by
the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies
thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover
any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the
sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold
“As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything
stated herein to the contrary.
Submitting A Claim:
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired
and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such
as a copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist
the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must
obtain a Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID
Number at https://rma.dlink.com/.
D-Link DIR-130 User Manual
67
Appendix D - Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping
package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside
of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective
portion of the product and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products
sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer
and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible
for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via
UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an
address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon
request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not
packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges
for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by
D-Link not to be defective or non-conforming.
What Is Not Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the
model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for
repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage
that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other
products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation
sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized
D-Link Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY
OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT.
D-Link DIR-130 User Manual
68
Appendix D - Warranty
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF
SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY,
SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY
OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY
CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR
LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF
OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION
OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE)
RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY
FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR
NONCONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE
PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES
ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply.
This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property
of their respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as
stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright © 2007 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
D-Link DIR-130 User Manual
69
Appendix D - Warranty
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required
to take adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local
D-Link office.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
IC statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
D-Link DIR-130 User Manual
70
Appendix E - GNU/Linux GPL
GNU/Linux GPL
• “GPL Software” means GPL software licensed to you under the GNU General Public License as published by the
Free Software Foundation (GPL). A copy of the GPL is included below.
• “Open Source Software” means various open source software components licensed under the terms of applicable open
source license agreements included in the materials relating to such software. Open Source Software is composed
of individual software components, each of which has its own copyright and its own applicable license conditions.
The Open Source Software licenses can be found in the gpl.pdf file, other materials accompanying the software
package, the documentation or corresponding source files available from http://support.dlink.com/GPL.asp.
D-Link DIR-130 User Manual
71
Appendix E - GNU/Linux GPL
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This
General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply
it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it
if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.
You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps:
(1) copyright the software, and
(2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on, we want its recipients to know that hat they have is not the original,
so that any problems introduced by others will not reflect on the original authors’ reputations.
D-Link DIR-130 User Manual
72
Appendix E - GNU/Linux GPL
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program
will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent
must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work
based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the
Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation
is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of
running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on
the Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of
this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange
for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and
distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any
change.
D-Link DIR-130 User Manual
73
Appendix E - GNU/Linux GPL
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program
or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users
may redistribute the program under these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based
on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can
be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections
when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise
the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete machine-readable copy of the corresponding source
code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and only if you received the program in object code or
executable form with such an offer, in accord with Subsection b above.)
D-Link DIR-130 User Manual
74
Appendix E - GNU/Linux GPL
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system
on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to
copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy
the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this
License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated
so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify
or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore,
by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do
so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from
the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any
further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by
third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program
at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to
apply and the section as a whole is intended to apply in other circumstances.
D-Link DIR-130 User Manual
75
Appendix E - GNU/Linux GPL
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by
public license practices. Many people have made generous contributions to the wide range of software distributed through that system in
reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through
any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Program under this License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such
new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies
to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version
published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose
any version ever published by the Free Software Foundation.
10.If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the
author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
D-Link DIR-130 User Manual
76
Appendix E - GNU/Linux GPL
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
D-Link DIR-130 User Manual
77
Appendix F - Registration
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty
rights.
Version 1.1
September 5, 2007
D-Link DIR-130 User Manual
78
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement