Bestway Hmax 58498E Owner's Manual
PDF
Download
Document
Advertisement
Advertisement
58498E Hmax 1.5 m TO THE STORE QUESTIONS? PROBLEMS? MISSING PARTS? For FAQ, Manuals, Videos Or Spare Parts, Please Visit bestwaycorp.com/support SAND FILTER OWNER’S MANUAL bestwaycorp.com/support Visit Bestway YouTube channel 303021216266 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-封面 SAFETY INSTRUCTIONS WARNING IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS WARNING - TO REDUCE THE RISK OF INJURY - do not permit children to use this product unless they are closely supervised at all times. WARNING - RISK OF ELECTRIC SHOCK - Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts. WARNING - The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI,push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using. CAUTION - To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool. DO NOT BURY CORD - Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment. WARNING - To reduce the risk of electric shock, replace damaged cord immediately. WARNING - To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable 2 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase. • THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3 • FOR USE WITH SWIMMING POOLS ONLY. • CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD,USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING. • WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE. • CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED POOLS. • CAUTION: CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER. • CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS. • WARNING - RISK OF ELECTROCUTION 1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin. 2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged. 3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground. 4) Do Not Touch Plug With Wet Hands. 5) Double Insulated – When Servicing Use Only Identical Replacement Parts. 6) Read Instruction Manual Before Using. DO NOT REMOVE THIS TAG SAVE THESE INSTRUCTIONS. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. 4 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 528 mm SPECIFICATIONS 254 mm 480 mm Filter Diameter: 254 mm Effective Fiter Area: 0.05 m2(0.54 ft2) Max. Operating Pressure: 0.83 Bar(12 PSI) Working sand filter pressure: <0.45 Bar(6.5 PSI) Max. Water Temperature: 35°C Sand: Not included Sand Size: #20 silica sand,0.45-0.85 mm Sand Capacity: Approximately 9 kg PARTS REFERENCE OVERVIEW Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts. A X3 B A C 26 (P61318) 5 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 X1 B X2 X2 REF.NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 (P6680) B 27 28 29 30 SPARE PART NO. P03831 P61138ASS16 P03832 P61209ASS16 P03837 P03838 P61211ASS16 P6581ASS16 P6580ASS16 P03839 P6614ASS16 P6029ASS16 P03830 P61214ASS16 P03841 P03829 P6916ASS16 P6124ASS16 P6561ASS16 P6562ASS16 P6563ASS16 P04320 P03836 P6517ASS16 P6680ASS16 P61318ASS16 P6019ASS16 P61408ASS16 P6005ASS16 P6783ASS16 X1 X1 A 1 1 2 1 1 1 1 1 1 1 1 6 1 1 8 1 2 5 1 1 1 1 1 2 2 1 2 1 2 1 B 1 1 2 1 1 1 1 1 1 1 1 6 1 1 8 1 2 4 1 1 1 1 1 2 2 0 2 1 2 1 C 1 1 2 1 1 1 1 1 1 1 1 5 1 1 8 1 0 0 1 1 1 1 1 2 0 0 0 0 0 1 Assembly (You will need a screwdriver.) 1. Carefully remove all components from the package and check to ensure nothing is damaged. If equipment is damaged, immediately notify the retailer from where the equipment was purchased. 2. The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filter so the Ports and Control Valve are accessible for operation, servicing and winterizing. 86 mm Ф8 mm 3. The sand filter must be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the sand filter from accidentally falling. Fully assembled sand filter will exceed 18 kg. The mounting holes should be 8 mm in diameter and spaced 86 mm apart. Use two bolts and nuts with a maximum of 8 mm in diameter to fasten the sand filter to the pedestal. Load pool-grade filter sand/Flowclear™ Polysphere. NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85 mm, approximately one 9 kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, thereby voiding the warranty. NOTE: To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub. NOTE: Sand/Flowclear™ Polysphere not included. NOTE: Use 0.06 lbs (28 g) Flowclear™ Polysphere to replace 2.20 lbs (1 kg) sand. 6 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 #20 0.45-0.85 mm 4 MAX. MIN . MAX MIN C C C Connect to the pool 1 A B A A A B B B 7 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 B 2 2 1 D A B B 3 D Garden hose (not included) For Drain, Backwash, Rinse function 3 A B B B P6680 4 A B B 8 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 For pool with 1.25 in. (32 mm) valve B A P6916 P61318 P61322/P6680 STOP Before switching on, please read the manual carefully. GFCI Test A C B D RESET RESET RESET TEST TEST TEST A. To test the GFCI plug, insert it into a grounding type receptacle. B. Press the “RESET” button; the indicator turns red. NOTE: If the indicator light is not on, the test has failed. C. Press the “TEST” button. The indicator turns off. NOTE: If the indicator light is not off, the test has failed. D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use. WARNING: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE. WARNING: DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales Service. OPERATION CONTROL VALVE OVERVIEW WARNING: To prevent equipment damage and possible injury, always switch off sand filter before changing the Control Valve function. Changing valve positions while the 9 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 pump is running can damage the Control Valve, which may cause personal injury or property damage. How to Use the Control Valve: Press down on the Control Valve handle and rotate to desired function. CONTROL VALVE FUNCTIONS The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash, Closed and Drain. Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool. A Closed: This function stops water flowing between the sand filter and the pool. C A C B B Backwash: This function is used to clean Rinse: This function for initial startup, cleaning, and sand bed leveling after Backwash; water is pumped downwards through the sand bed, up through the Collector Hub and deposited out of the valve Port D. the sand bed; water is pumped down through the Collector Hub, upwards through the sand bed, and deposited out of Port D. A C A D C D B B Circulate: This function circulates pool water Drain: This function drains water from the pool; by passing the sand filter; use this function if the filter is broken to collect debris in the Debris Screens. another filter bypass setting, water is pumped and deposited out of Port D, instead of returning it to the pool. A C C A D B B 10 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 NOTE: • Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage. • When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve. • Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter. • Do not set the Control Valve between two functions, or it will lead to leaking. • To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter. Air Release Press down the control valve handle and wait untill the water flow from Port D to release the air. NOTE: It is important to repeat this operation every time you start the pump after winterizing, maintenance and backwashing the sand bed. FIRST TIME USE INSTRUCTIONS Backwash and Rinsing must be performed to prepare the pump for its first use and to wash the sand. CAUTION: DO NOT DRY RUN THE SAND FILTER 1. 2. 3. 4. Press down on the Control Valve handle and rotate to the Backwash function. Plug in and run the sand filter for 3-5 minutes, or until the water runs clear. Switch off the sand filter and set the Control Valve to the Rinse function. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D. 5. Switch off the sand filter. Set the Control Valve to the Closed function. 6. Top up pool water if required. IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Rinsing Switch off the sand filter immediately if water Backwash levels near the pool’s Inlet and Outlet valves. 11 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 1. Now the sand filter is ready for use. Set the Control Valve to the Filter function. NOTE: To prevent the risk of electrical shock dry any excess water from yourself and the sand filter. 2. Switch on the sand filter to run it. NOTE: The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running. Sand Filter Maintenance CAUTION: You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists. As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the pool is too low, it is time to clean the sand. To clean the sand bed, follow all instructions outlined previously in: Backwash and Rinsing. 0. 8 1 6 0. 10 0. 4 1. 2 15 5 psi bar 1. 6 0. 2 1. 4 20 23 0 0 NOTE: 1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement. 2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used. Do not clean the sand too frequently. 12 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 Cleaning the Strainer 1. Switch off the sand filter and set the Control Valve to the Closed function. 2. Close the connection valves. 3. Remove the Strainer Cover by unscrewing it. 4. Take out the Strainer, remove any debris. 5. Put the Strainer back into position. Ensure the hole in the strainer is aligned. 6. Ensure the Seal Ring is in place. Secure the Strainer Cover back. 7. Open the connection valves. NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked strainer will reduce the performance of the sand filter. Lowering or Draining Pool Water 1. Switch off the sand filter and set Control Valve to the Drain function. 2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D. 3. Switch on the sand filter to remove pool water. WARNING: DO NOT DRY RUN THE SAND FILTER. Winterizing In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty. 1. Backwash the sand filter. 2. Drain the pool according to the pool owner’s manual. 3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water. 4. Disconnect the two Hoses from the pool and the sand filter. 5. Completely pour the sand out of the tank and dry all components. 6. Store the sand filter in a dry location out of child’s reach. 13 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 TROUBLESHOOTING Problems Probable Causes Solutions Sand Filter does not operate - GFCI broken - Contact your local Bestway Aftersales Service point to get instructions Sand is flowing to the pool - Sand is too small - Move the control valve from the backwash to the filter function without stop the sand filter - The level of the sand is too high - The skimmer is broken - Recommend 0.45 mm to 0.85 mm #20 silica sand - Stop the sand filter every time set the control valve - Check if the level of the sand is between the marked “MAX” and “ MIN” on the hub - Replace the skimmer No water flow - Stopper plugs were not removed - Air was not released - The control valve is set to Closed - The strainer is blocked - Sand filter broken - Remove the stopper plugs and insert the debris screens - Release the air - Set to filter function - Clean the strainer - Call for service Excessive filter pressure - Dirty filter - Calcified sand bed - Insufficient backwashing - The pressure gauge is broken - Backwash - Inspect sand and change if necessary - Backwash until water runs clear - Replace the pressure gauge Control Valve leaks from the port D - Control Valve is set between two functions - The gasket is broken - Set to one function - Replace the gasket Connectors leaks - Washer of the connectors not in place - Washer of the connectors broken - O-ring on the hose connection is broken - Loose Hoses - Reposition the washer - Replace the washer - Replace the o-ring - Tighten them 14 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 For support please visit us at: bestwaycorp.com/support ©2019 Bestway Inflatables & Material Corp. All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati ®™ Trademarks used in some countries under license to/ Marques ®™ utilisées dans certains pays sous la licence de/ Marcas comerciales ®™ utilizadas en algunos países bajo la licencia de/ ®™ Die Warenzeichen werden in einigen Ländern verwendet unter Lizenz der/ ®™ Marchi utilizzati in alcuni paesi concessi in licenza a Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China. Manufactured,distributed and represented in the European Union by/ Fabriqués, distribués et représentés dans l’Union Européenne par/Fabricado, distribuido y representado en la Unión Europea por/ Hergestellt, vertrieben und in der Europäischen Union vertreten von/Prodotto, distribuito e rappresentato nell'Unione Europea da Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy Distributed in North America by/Distribués en Amérique du Nord par/Distribuido en Norteamérica por Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America Tel: +86 21 69135588 (For U.S. and Canada) Distributed in Latin America by/Distribué en Amérique latine par/Distribuido en Latinoamérica por/Distribuído na América Latina por Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, 98-104 Carnarvon Street, Silverwater, NSW 2128, Australia Tel: Australia: (+61) 29 0371 388; New Zealand: 0800 142 101 Exported by/Exporté par/Exportado por/Exportiert von/Esportato da Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong www.bestwaycorp.com Made in China/Fabriqué en Chine/Fabricado en China/Hergestellt in China/Prodotto in Cina 303021216266_58498E_14x21cm_1500gal 美国规砂滤器说明书-英 ">

Public link updated
The public link to your chat has been updated.
Advertisement