G6

BT Interphone

New version

Hi-Fi speakers, Top sound quality!

USER MANUAL

Cool multifunctional communication tool for motorcyclists !!

Main Features:

Communication in 6 riders, one rider can pair with 5 riders, and can choose which person of the group to talk at a time. real full duplex wireless communication in 6 riders by bluetooth system

Maximum talking range 1000 meters

Up to 120Km/h working speed

Up to 9 hours talking time

Safe auto-receiving cell phone calls

Advanced A2DP & EDR bluetooth profile ,

Top sound quality, with new Hi-Fi speakers in this new version of

G6 intercom

Stereo music/audio function(transmits from A2DP enabled cell phone / MP3 / GPS )

Line in audio interface, can connect with any audio source

Wind noise DSP cancellation

Water-resistance, full weather

Introduction :

-------------------------------------------------------------------------1------------------------------------------------------------------------------

We will describe this communications kit as G6( a Group can contain maxium 6 riders)

This G6 can either be used for rider or for pillion.

This G6 can connect with three kinds of bluetooth devices: a bluetooth enabled cell phone, five G6 (or: four riders and 1 pillion), an audio source which with a built in or a external audio bluetooth transmitter.

This G6 is a multifunctional device for motorcyclists and skiers, it can be used:

1)

As a handfree bluetooth headset for cell phone calls, while out riding, the auto answer feature of the internal Bluetooth profile enables safe automatic handfree answering of the phone call automatically. It also offers a call rejecting function.

—receive the cell phone calls even you do not need to press any button, you just need to rider

your bike as normal

, the process of receiving call will be automatic, after ring on of the call about 5 seconds , it will receive the call automatically.

2) As a two way wireless full duplex interphone in 6

riders or between rider & pillion,

Any rider could choose one of 5 riders to talk at a time !

The maximum communication range over a high clear line of sight path can reach

1000m !

(this maximum range is not guaranteed) .

Typical effective range in city is approximately 700m. Please note that actual range will depend on weather conditions, terrain, presence of obstacles i.e. a large vehicle, buildings non line of sight etc.

Unlike a one-way walkie talkie, which is only half duplex i.e. it can not speak and listen simultaneously, the

G6 offers real-time talking like a normal telephone.

It can connect with 5 other riders or connect with anther rider and his/her pillion.

The rider can chose which person to talk with

The working speed can be up to 120km/h !

3) As a wireless bluetooth stereo music receiver and speaker, this G6 has

EDR and A2DP

profile , with EDR and

A2DP profile it can offer another important function--- listening to stereo music from A2DP enabled cellphone,MP3 or navigation audio information from GPS

(this MP3 or GPS should has a built in audio bluetooth

transmitter)

4) As a bluetooth headset for receiving GPS navigation audio instructions

(this GPS should have a built in bluetooth transmitter)

5) As the speakers of your MP3/GPS

If your MP3 or GPS is not Bluetooth transmitting enabled and you have not a Bluetooth AV dongle, this G6 also offers another method of listening to the stereo music/audio info--- the simple wired method. Plug the audio source directly into the G6 via the 2.5mm-3.5 mm stereo connection cable.

--------------------------------------------------------------------------2-----------------------------------------------------------------------------

Components of retail box

Component

G6 headset main part

Parts Number

Clip for mounting the main unit

Hi-Fi Speakers & microphone & audio plug

G6 -001

G6 -002

G6 -003

AC &USB Charger (AC110V-220V / DC

OUTPUT 5V)

2.5mm to 3.5mm audio adapter cable

G6 -004

G6 -005

G6 -006 User manual

Main G6 communications unit

-------------------------------------------------------------------------3-----------------------------------------------------------------------------

Clip & hanging-hole for mounting the main G6 unit

Clip Inserted plate

Hi-Fi Speakers/Boom Microphone/audio plug

-------------------------------------------------------------------------4-----------------------------------------------------------------------------

The AC & USB Charger

Note: Different country may has different adaptor

Before using: Charging the G6

Before using this device, Please charge the

G6

main device at least three hours.

We have provided you with the ability to charge the system via the USB port of your computer or if you are away on a trip, you can use the supplied Multi-voltage USB power adapter.

The charging cable has a small USB plug for the headset and the large USB plug for the computer or AC adapter, please observe to correct orientation of the USB plug and socket before inserting

1) Insert the 2.5mm plug of the charging cable, into the small charging jack of the

G6

, you can either charge by computer or AC adapter.

2) While charging, the red LED on the headset module will illuminate,

When the charging is finished, the red LED will extinguish.

Note:

if you do not use the G6 for a month or more, to protect the Poly-Li battery, please charge the G6 at least every month.

(The fault damaged by wrong charging will be not guaranteed).

Attaching and removing the G6 main unit on your helmet

With the clip, you can easily mount the main unit of the G6 on a helmet within 3 minutes.

Step:

1) Find a best position on the

left

side of your helmet to put the clip

2) Insert the inserted plate between shell and foam of the helmet

Fix the clip on the helmet with the screws

3) hang the main unit of the

G6

on the clip

Clip Inserted plate for clip

-------------------------------------------------------------------------5-----------------------------------------------------------------------------

Insert the plate between the shell and the foam of a helmet, fix with screws

Clip fixed on helmet

G6

mounted on a helmet

Attaching the two speakers and the microphone

The success of the system depends on the careful positioning of the ear speakers directly over top of the ear canals. this will give the best signal to noise of the received audio..

1) To find the position of your ear canals, put your helmet on firmly but don’t do it up. Slide your thumb of one hand up between the inside of the helmet and your ear, with the fingers of that hand on the exterior of the helmet. Feel the ear canal in your ear with your thumb and then grip the helmet firmly between thumb and fingers of that hand, carefully take the helmet off BUT don’t move your thumb from its position inside the helmet. Look at where your thumb it! This place marks the centre of the ear speaker! Mount the Velcro pad to which the speaker will attach there, inside the helmet, Check the other side for optimum ear speaker position.

-------------------------------------------------------------------------6------------------------------------------------------------------------------

2) Remove the protective backing of the Velcro and mount the Velcro pads in the correct positions, attach the two speakers on the Velcro inside your helmet, the speaker with

short wire cord for

left

ear, the speaker with long wire cord for right ear. the speaker with short wire cord the speaker with long wire code for left ear for right ear

Adjust the position of the microphone

Note: To reduce the external noise, you need to close the visor while riding, and please adjust the position of

the microphone to be right in front of your mouth with the foam just touching your lips, the visor should cover

the microphone effectively! (Minimizes wind noise contribution)

V

X

Correct position of the microphone Wrong position of the microphone

3) Plug in the positioned headset to the communications module and attach it to the side of the helmet.

Operation:

The operation is friendly and very easy.

Pairing with your Bluetooth phone for the first time

Note: You must have a Bluetooth enabled phone to “Pair” with the G6

The rider and pillion pairing their headsets with their respective mobile phone should be at different time,

Before using the G6, please familiarize yourself with Bluetooth function of your cell phone. Read the instruction manual that came with the phone so you can enable its Bluetooth function.

Before you can use this G6 in combination with your phone, you will need to “pair” it with your cell phone for the first time.

This usually only needs to be performed once with that individual phone however follow the instructions supplied by the phone manufacturer and save the “pairing” so it will be automatically connected when this Phone and the G6 come into contact again.

-------------------------------------------------------------------------7-------------------------------------------------------------------------------

1) Enable the Bluetooth function on your cell phone. Short press (< 1 second) Reset key on the G6.

2) You must place the

G6

in “Pairing mode”, this is done by way of a holding down the Power/Interphone key on the headset, until the red & blue LED flash alternately.

3) Begin the “searching for Bluetooth device” on the cell phone according to the phone’s instructions

4) when the

G6

is discovered, the cell phone will display MOTOR PHONE select this and accept the connection

5) The cell phone will ask you to input a password to enable this connection , when prompted input password :

0000 (four zeros)

6) Your phone will confirm that pairing has succeeded. Note that the only light showing on the headset is now the blue one and it will flash once every 5 seconds

Basic G6 Operation

Turn on

Short press (< 1 second) Reset key on the G6.

Press the Power/ RIDER A key for 6 seconds or so , until the blue lamp illuminate, promptly release the

Power/Interphone key, then the blue led will flash every 2-5 seconds, and you can see that on the screen of your cell phone the G6 will ask your cell phone to connect with it , select ”yes” on your phone then they will connect each other.(for some phones, you will have to connect the G6 by the phone)

Turn off press the Power/Interphone key for 6 seconds or so , until the blue lamp long illuminate, promptly release the Power/RIDER A key then the blue led will extinguish.

Increase the volume Short press of the V+ key

Reduce the volume Short press of the V- key

Re-connect the cell phone For some reason(e.g. In some regions of high RF strength), may the G6 will lose connection with the cell phone, a short press on the Phone/Play key, they will connect each other again.

Safe Cell phone calls function

1) Receive a cell phone call automatically

When income a cell phone call, you will hear the ring on the cell phone and about 3-5 seconds later, the G6 will receive the call automatically.

2) Terminate cell phone call

When you finish talking on the cell phone, a short press the Phone/Play Key, will terminate the call.

3) Reject a cell phone call

When income a cell phone call, you will hear the ring, within 1 second immediately press the Phone/Play key about 2 seconds, it will reject the call.

--------------------------------------------------------------------------8-----------------------------------------------------------------------------

4) Make a cell phone call

Dial a number on your phone as normal, ( but don’t do this if you are on road for your safety) the sound will be automatically heard in your headset

notice: some phones, like Panasonic x70, will not send the audio to the headset, you may have to press the Phone/Play key to transmit the sound to your headset

5) Dial the last number Press the Phone/Play key 2-3 seconds, it will dial the phone number that you dialed last time. (note: some cell phone do not support this function)

Interphone Function

Set up for bike- to- bike and rider-to-pillion intercom: pairing

Pairing is a one time process that is required for mutual recognition between a G6 and other G6.once the two headsets are paired, they will retain paired whenever they are within range .

Please note that you can speak via intercom to one buddy headset at a time.

Note: a.

when you are pairing two G6s, you must keep other G6s in status of power off.

b.

You could pair your G6 with maximum total five G6s, you also could only pair your G6 with one G6. c. Please

note !

:

because the POWER/RIDER A key is a multifunctional key, so

once you have defined one

of other G6s as rider A, the method that pair your G6 or other G6s with rider A will be different to the

way of pairing with rider B, C, D, E, F. before you pair your G6 with another G6(rider A) by

POWER/RIDER A key, please confirm your G6 is in status of power off.

1) Pairing two G6s

Maybe you only need to communicate with a person (a rider or a passenger), you can simply pair two G6s according to below step:

To be sure that your

G6

and rider A(another G6) are in status of power off.

Short press(< 1 second) Reset key on your

G6

and on another

G6

, simultaneously hold the POWER/RIDER A key on your

G6 and

hold the POWER/RIDER A key on another

G6

until the red & blue LED of the two pairing

G6

s flash, short press the POWER/RIDER A key on

one of

G6

, 5-9 seconds later the red LED of both G6s will extinguish and the blue LED then will flash briefly every 2-5 seconds, thus they have finished the pairing(now you could talk with another

G6

).

3) Pairing all G6s

-------------------------------------------------------------------------9------------------------------------------------------------------------------

To avoid being confused, please stick respectively 6 label of A, B, C, D, E, F on 6 units of G6s

Note:

one time it only allows one of other five G6s to pair with unit A, and when you are pair two G6, please confirm that other units are in status of power off.

1. Pair B, C, D, E, F G6s with unit A

1.1

Pair unit B with unit A

Power on unit A, power on unit

B

(the blue LED of unit

A

and

B

will flash).

Simultaneously hold the

B

key on unit A and hold the A key on unit

B

until the red & blue LED of the both pairing

G6

s flash, short press the

B

key on unit A, 5-9 seconds later the red LED of both G6s will extinguish and the blue

LED then will flash briefly every 2-5 seconds, thus they have finished the pairing (now you could talk each other).

1.2

Pair unit C, D, E with unit A, the way is same to above 1.1. for example, pair unit

C

with unit A as below :

Power on unit A, power on unit

C

(the blue LED of unit

A

and

C

will flash).

Simultaneously hold the

C

key on unit A and hold the A key on unit

C

until the red & blue LED of the two pairing

G6

s flash, short press the

C

key on unit A, 5-9 seconds later the red LED of both G6s will extinguish and the blue

LED then will flash briefly every 2-5 seconds, thus they have finished the pairing (now you could talk each other).

1.3

Pair unit F with unit A

Because there is not F key on G6, so the way of pairing unit F with unit A is different a bit.

To be sure that unit A and

F

is in status of power off,

Simultaneously hold the

A

key on unit A and hold the A key on unit

F

until the red & blue LED of the both pairing

G6

s flash, short press the

A

key on unit A, 5-9 seconds later the red LED of both G6s will extinguish and the blue

LED then will flash briefly every 2-5 seconds, thus they have finished the pairing (now you could talk each other).

2.

Pairing between unit B, C, D, E

For Example: pair unit B with unit C

Power on unit

B

(the blue LED of unit

B

will flash), Power on unit

C

(the blue LED of unit

C

will flash).

Simultaneously hold the

C

key on unit

B

and hold the

B

key on unit

C

until the red & blue LED of the both pairing

G6

s flash, short press the C key on unit

B

, 5-9 seconds later the red LED of both G6s will extinguish and the blue LED then will flash briefly every 2-5 seconds, thus they have finished the pairing (now you could talk each other).

3.

Pairing unit B, C, D, E with unit F

Because there is not F key on G6, so the way of pairing unit F with unit B,C,D,E is different a bit.

For Example: pair unit B with unit F

Power on unit

B

(the blue LED of unit

B

will flash), Power on unit

F

(the blue LED of unit

F

will flash).

Simultaneously hold the

B

key on unit

B

and hold the

B

key on unit

F

until the red & blue LED of the both pairing

G6

s flash, short press the

B

key on unit

B

, 5-9 seconds later the red LED of both G6s will extinguish and the blue LED then will flash briefly every 2-5 seconds, thus they have finished the pairing (now you could talk each other).

--------------------------------------------------------------------------10----------------------------------------------------------------------------

To get all pairing details, please refer to below pairing chart,

WHEN RED AND

INTERPHONE unit A unit A unit unit unit

A

A

A unitB unitB unitB unitB unitC unitC unitC unitD unitD unitE

PAIRING

BUTTON

B

C

D

E

POWER/A

C

D

E

B

D

E

C

E

D

E

STATUS

BEFORE

PAIRING

BLUE LED FLASH

ON BOTH powered on powered on powered on powered on powered off

PRESS BELOW

BUTTON ON LEFT

UNIT

B

C

D

E

POWER/A

<< --pair each other -->>

<< --pair each other --unit B

<< --pair each other --unit C

<< --pair each other --unit D

<< --pair each other --unit E

<< --pair each other --unitF powered on powered on powered on powered on powered on powered on powered on powered on powered on powered on

C

D

E

B

D

E

C

E

D

E

<< --pair each other --unit C

<< --pair each other --unit D

<< --pair each other --unit E

<< --pair each other --unitF

<< --pair each other --unit D

<< --pair each other --unit E

<< --pair each other --unitF

<< --pair each other --unit E

<< --pair each other --unitF

<< --pair each other -->> unitF

PAIRING

BUTTON

STATUS

BEFORE PAIRING

POWER/A powered off

POWER/A powered off

POWER/A powered off

POWER/A powered off

POWER/A powered off

B powered on

B powered on

B

B powered on powered on

C powered on

C

C powered on powered on

D powered on

D powered on

E powered on

Pairing these riders seems a bit complicated, but using the intercom is very simple ☺

After you have paired with all the G6s (you also could only pair with1-4 riders), then you will can talk with one of the riders at a time.

STEP:

after finishing the pairing procedure, confirm that all of G6s have been powered on .

Initiate an intercom call (a short press one of intercom key A, B, C, D, E on your

G6

), and then you can talk with one of other riders.

For example:

A short press(< 1 second) the C Key, promptly release your hand, you will hear a beep “di”, then wait about 3-5 seconds you could talk with rider C. if then you short press the E key, it will change the communication to talk with rider E.

Tips: Talk with unit F

Because there is not

F

key on the unit, so the way of calling unit

F

is different:

Short press A key on unit A, you will talk with

F.

Short press B key on unit B, you will talk with

F.

………

Short press E key on unit E, you will talk with

F.

Finish an interphone talking

You only need a short press of same one of the intercom (A, B, C, D, E) key, to terminate communications

Note: to reduce power consumption, when you do not need to talk, don't keep your G6 on intercom state in a long time

-------------------------------------------------------------------------11--------------------------------------------------------------------------

Note: If two G6s were out of range, they may will lose connection. when you come within range, you only need to initiate a intercom as normal.

Music /Audio function

1) listen to audio navigation info from your GPS which with a built in bluetooth transmitter a)

Pair this GPS with your G6

Be sure that you have turned off the bluetooth function on your mobile phone.

Be sure that the G6 is in the state of power off.

Power on the GPS, hold the bluetooth key on the GPS until the red & blue LED flash.

Long press the POWER/Rider A key on the G6, until the red & blue LED flash.

About several seconds later, the red LED of the GPS and the G6 will extinguish at the same time, thus they have paired successfully.

b) Enjoy audio info of the GPS on the G6.

Adjust screen tap sound and volume to an appropriate level on the GPS, then the user can enjoy the audio information on the G6.

Note:

please obey the bluetooth Power On sequence as below:

G6 first , then GPS.

please obey the bluetooth Power Off sequence as below:

GPS first, then G6

2) Listen to stereo music from your A2DP enabled cell phone

Read the user manual of your cell phone carefully, if your cell phone is A2DP enabled, the G6 can receive the stereo music from the cell phone.

Please note that only A2DP (stereo bluetooth) enabled cell phone can offer bluetooth music transmitting service.

You can use the Phone/Play key to pause/play the music from A2DP bluetooth devices.

3) Listen to music from some mono bluetooth enabled cell phone

Almost all of Nokia mono bluetooth enabled cell phone can offer bluetooth music transmitting service, but some model of other brand cell phone can not offer this service.

We do not promise that the G6 will support music function for all mono bluetooth enabled cell phones.

Step: confirm that your G6 has paired with your cell phone; play the music on the cell phone, and then you can enjoy the music on your G6.

Note: for mono bluetooth cell phone, you can not use the Phone/Play key to operate the music, you only can operate the music on the phone.

4) listen to stereo music from your MP3 by Wired method

2.5-3.5mm audio adapter cable

-------------------------------------------------------------------------12----------------------------------------------------------------------------

With the 2.5-3.5mm audio adapter cable attached, it will can be used for connecting your G6 with a major of

MP3. play the MP3, you will can listen to the music via the speakers of your G6.

NOTE1:

when the G6 is working in bluetooth status, it will mute the music of the MP3. bluetooth is prior. After bluetooth operation is finished, it will return to play the MP3 music.

NOTE2: you only can adjust the music volume on your MP3.

5) listen to audio navigation info from your GPS by Wired method

the way is same to listening to music from a MP3.

6) listen to stereo music from MP3 via external audio bluetooth transmitter

If you have a external audio bluetooth transmitter (it is easy to find this product in the market), insert the plug of the transmitter into the jack of the MP3.

Pair the transmitter with the G6 according to the instruction manual of the transmitter.

Play the MP3, you can listen to the music on your

G6

.

7) listen to audio navigation info from your GPS via external bluetooth transmitter

The way is similar to 5) above.

8) listen to stereo music from MP3 which with a built in bluetooth transmitter

please familiarize yourself with Bluetooth function of your Bluetooth enabled MP3(this MP3 must has

Bluetooth transmitting function). read the instruction manual that came with the MP3 so you can enable its bluetooth function. pair the MP3 with the

G6

according to the instruction manual of the MP3. play the MP3, you can listen to the music on your

G6

.

Auto switch between different operations

While talking by intercom or listening to music, if it incomes a cell phone call, the voice will be switched to

“cell phone talking” state automatically. After the call has been hung up, the system will auto return to intercom talking or music playing state.

While listening to music, short press the RIDER A or RIDER B, C, D, E key, it will initiate a intercom talking. after terminating the intercom talking, the system will return to the music automatically.

Note: it might needs about 5 seconds to auto-return to “intercom talking” state after the “cell phone talking” has been hung up.

Trouble shooting

1.

not working

Could be a flat battery , charge the G6 3 hours.

2.

Reset

In some regions of high RF strength ie near high power TV transmitters, GSM station or airport radars, these can overwhelm the CPU in the G6 causing it to latch up.

Short press (< 1 second) Reset key on the G6.

when you turn on the G6, it will work normally again.

3. No sound

Physically check to see the headset cables are ok or the audio plug is real inserted in the jack?

swap with the other functioning G6 to localize the problem. have you turned to volume too low?

4. Whistling of the speakers

If the microphone is too closed a speaker, the speaker will make a whistling, take the microphone away from the speaker, reduce the volume by the Volume-key, it will be ok.

5.Lose connection with the cell phone or music from the cell phone

For some reason (e.g. in some regions of high RF strength), maybe the G6 will lose connection with the cell phone or music from the cell phone, a short press on the

Phone/Play key, they will connect each other. or see the below 8.

-----------------------------------------------------------------------13------------------------------------------------------------------------------

6. can not connect with your mobile phone

This G6 can connect with a major of bluetooth enabled cell phone of main brand, but we don't undertake that

it can connect with all cell phone. Before purchasing, please confirm that if the G6 could connect with your cell phone.

7. auto-power off

To cell phone call, intercom, music these different using, This G6 takes different Bluetooth profile. when change between different using, it will change to the corresponding profile.

Some cell phone maybe do not take standard bluetooth profile, when it connect with the G6, some times it may cause turning the G6 off when the G6 are switching between three different state(call, intercom, music ). in this case, you could turn on the G6 again by pressing the Power/Interphone key, and note that only make the G6 working on two profile.

8. Final solution

If the solution of above clause1.- 7.can not resolve the problem, turn your cell phone off (sometimes you may have to take off the battery of your cell phone and load the battery again) and your G6, then turn them on and pair them again.

9. .Lose connection between two G6s

If two G6s were out of range, they may will lose connection. when you come within range, you only need to initiate a intercom as normal.

OTHER FEATURES

·Digital Signal Processor (DSP) Technology for wind noise cancellation

·Excellent performance at speeds up to the legal limit with a full face helmet

·Easily mounts to all full face and open face helmets

GENERAL FEATURE

·Up to 7 hours talk time when connected to your cell phone

·UP to 7 hours time when listening to music

· 500 mAh Li Polymer battery ·Standby time: 120 hours

·Charging time:~ 3 hours

·Chip brand: CSR

SPECIAL FEATURE

·All weather, rain and snow resistance

Thank you for using the G6 BT Interphone !

-------------------------------------------------------------------------14-----------------------------------------------------------------------------

G6

motorcycle multi-interphone