Quoizel ER353BN Emery 3-Light Brushed Nickel Chandelier Instructions

Quoizel ER353BN is a stylish and functional light fixture that can be used to illuminate a variety of indoor spaces. It features a brushed nickel finish and a classic design that will complement any décor. The fixture comes with all the necessary hardware for easy installation, and it can be customized to your desired length using the included rods and chain. The ER353BN uses standard medium base bulbs, and it is compatible with both incandescent and CFL bulbs.

PDF

Document

Quoizel, Inc.

6 Corporate Parkway

Goose Creek, SC 29445

Customer Service

Phone 631.273.2700

Fax 631.231.7102

www.quoizel.com

Assembly Instruction Sheet #IS-ER353BN

For Style ER353BN

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Bulb Recommended: (3) Medium Base 100W bulbs Maximum, Alternate bulb (3) 23W CFL Maximum.

Estimated Assembly Time: 30-45 minutes

Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

Fixture Loop x 2

”

Rod x 4

12 ” Rod x 4

Lock Screw x 2

Cap A x 2

Cap B x 2

Upper Collar x 3

Hardware Contents

Ceiling

Canopy x 1

Shade x 3

Fixture Chain x 2

Crossbar

Assembly x 1

Quick Link x 4

Steel Collar x 3

Harp with

Socket Collar x 3

STEP 1 Attach Caps to Socket

Assembly

A. Attach the Caps (P/Q) to the ends of the

Socket Assembly (R) and secure with the

Lock Screws (O). Hand tighten until snug.

R Q O

Nipple x 3

Flat Washer x 3

Figure 1

STEP 2 Assemble the Rods and the Fixture Loop

Rubber Washer x 3

Hex Nut x 6

Small Flat

Washer x 3

Finial x 3

Diffuser x 3

A. Determine the Rods (B/C) to be assembled to the Socket Assembly

(R) according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(B/C) and the Fixture Loop (A). Thread the Socket Assembly (R), the chosen Rods (B/C) and the Fixture Loop (A) together. Hand tighten until snug.

Figure 2

Supply Wires and Ground Wire

Socket

Assembly x 1

2014 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

1of3

March2014

STEP 3 Install Fixture Chains BB

A. Adjust the Fixture Chain (CC) to your desired length by removing the links if needed.

* Pliers is required for this step.

B. With the Fixture Chain (CC) not attached to the Fixture Loop (A) and the Canopy Chain Loop, pull the supply wires through the Fixture Chain

(CC) alternating links. After the wires are through the Fixture Chain (CC), pull the Supply Wires and the Ground

Wire through the Ceiling Canopy (BB).

C. Attach one ends of the Fixture Chains

(CC) to the Fixture Loop (A) with two

Supply

Wires

Ceiling

Loop

Quick Links (DD) as shown. Lift the fixture and Fixture Chains (CC) up and attach the other ends of the Fixture Chains (CC) onto the

Canopy Chain Loop underside of the Ceiling Canopy (BB) with the rest two Quick Links (DD).

from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from fixture.

E. Twist connectors until wires are tightly joined together.

F. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.

STEP 7 Install Ceiling Canopy

A. Attach the Lock Washer, the Ceiling

Canopy (BB) and the Covers over the end of the Nipple as shown. Secure by threading the Finial onto the

Nipple. Hand tighten until snug.

BB Nipple

Lock Washer

Cover A

Cover B

Finial

Figure 7

Suggested rods and chain length for Ceiling height :

’ ceiling : use (1)6

” rod and 2 quick links

9 ’ ceiling : use (1)12 ” rod, 5 links of chain and 2 quick links

10 ’ ceiling : use (2)12 ” rods, 5 links of chain and 2 quick links

STEP 8 Install Shade

Socket

STEP 4 Separate parts from Crossbar Assembly

A. Remove the Finial, the Covers, and the Lock Washer from the

Crossbar Assembly (AA).

A. Place the Upper Collar (D), the Shade (E) and the Steel Collar (F) in turn and secure with the Harp with Socket Collar (G). Hand tighten until snug.

Figure 4

Nipple

Lock Washer

Cover A

Cover B

Finial

STEP 5 Install Crossbar

Attach the Crossbar ( AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) .

Tighten until snug .

STEP 9 Install Bulb

Figure 8

A. This fixture uses standard bulb with medium base. Maximum 100 watts.

B. Insert bulb and screw snugly into place.

Figure 9

Green

Ground Screw

White wire from supply

Black wire from supply (or Red)

Ground wire from supply

Outlet Box

Figure 5

Outlet Box Screw

(not included)

STEP 6 - Wire Connections

A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

STEP 10 Install Diffuser

A. Thread one Hex Nut (K) to the Nipple

(H) approx half way. Screw the Nipple

(H) into the bottom end of the Harp (G) and tighten until snug. By using pliers, thread the Hex Nut (K) against the Harp

(G) and hand tighten until snug.

B. Thread another Hex Nut (K) onto the end of the Nipple (H) and adjust it to proper location for rest components.

Attach the Flat Washer (I), the Rubber

Washer (J), the Diffuser (L) and the

Small Flat Washer (M) over the Nipple

(H) in turn. Secure them with the Finial

(N) and hand tighten until snug.

Your fixture is now assembled and ready to use. Enjoy!

Figure 10

Figure 6

Bulb

2014 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

2of3

March2014

ER353BN

FINISH: BRUSHED NICKEL

9 ” x4.5

”

1 ”

”

OVERALL HEIGHT

INCLUDES 12 ”

CHAIN AND

(4) QUICK LINKS

60 ”

OVERALL HEIGHT

INCLUDES

(4)6 ” AND (4)12 ” RODS

23 ”

(3) 100W

Base

Medium

Bulbs

(Not Supplied)

NO.

PART NUMBER

G134DI

M2127SH

REPLACEMENT PART DESCRIPTION

DIFFUSER 11.5"D

METAL SHADE BRUSHED NICKEL 13.5"D

52.5

”

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2

REQ.

9006EXBN

9012EXBN

ROD EXTENSION BRUSHED NICKEL 6"L X 0.5"D

ROD EXTENSION BRUSHED NICKEL 12 ” L X 0.5"D

13.5

”

Dia.

2014 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

3of3

March2014

Hello! I am an AI chatbot specifically trained to assist you with the Quoizel ER353BN Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!