KTR DATAFLEX 70 Series Operating & Assembly Instructions
PDF
Download
Document
Advertisement
Advertisement
DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions KTR-N Sheet: Edition: 49017 EN 1 of 21 3 DATAFLEX® Torque measuring shaft type 70/… Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions KTR-N Sheet: Edition: 49017 EN 2 of 21 3 DATAFLEX® is a maintenance-free torque measuring shaft with integrated speed measurement. Combined with the steel lamina coupling RADEX®-N the complete system forms a torsionally stiff, double-cardanic coupling with integrated measuring shaft. Table of contents 1 Technical data 3 2 Advice 5 2.1 2.2 2.3 2.4 5 5 5 6 3 4 General advice Safety and advice symbols General hazard warnings Intended use Storage, transport and packaging 6 3.1 3.2 6 6 Storage Transport and packaging Assembly 7 ® 4.1 4.2 4.3 4.4 4.5 Components of DATAFLEX torque measuring shaft Advice for finish bore Displacements - alignment of the torque measuring shaft Assembly of the hubs Assembly of the RADEX®-N clamping ring hubs on the DATAFLEX® torque measuring shaft 4.6 Assembly of hubs on the driving and driven side 4.7 Assembly of lamina sets 4.8 Tightening torque of the fit bolts 4.9 Advice for assembly of the DATAFLEX® torque measuring shaft 4.10 Technical description 9 10 11 11 12 12 5 Disposal 20 6 Maintenance and service 20 7 Services, customer service addresses 20 8 EC Certificate of conformity 21 Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: 7 8 8 9 KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 1 KTR-N Sheet: Edition: 49017 EN 3 of 21 3 Technical data DATAFLEX® torque measuring shaft Illustration 1: DATAFLEX® torque measuring shaft Table 1: Dimensions ® DATAFLEX type 70/3000 70/5000 d D L1 L2 70 130 330 100 Dimensions [mm] L3 L4 130 118 L5 H B X 6 107.35 50 23 Table 2: Technical data Coupling size of DATAFLEX ® 70/3000 70/5000 Electrical data Rated torque TKN [Nm] Band width of torque signal [kHz] (-3dB) 1) Error in linearity incl. hysteresis [%] Influence of temperature [%/10K] Nominal temperature range [°C] Supply voltage [V] DC Max. current consumption [mA] -3000 .. +3000 Nm -5000 .. +5000 Nm 2 < 0.1 0.05 0 - 55 24 ± 4 100 Torque output Output voltage torque [V] -10 .. +10 Speed output 2) Number of pulses / revolutions Amplitude [V] DC voltage output [V] Scale of DC voltage output 3) Inaccuracy of DC voltage output [%] Direction signal [V] 2 x 450 24/5V 0 - 10 16fold via micro switch ± 0.2 24/5V Mechanical data 1) Static load limit TKmax. [%] 1) Breaking load TK break [%] Max. bending torque [Nm] Max. radial force [N] Max. axial force [kN] Weight [kg] Torsion spring stiffness CT [Nm/rad] Torsion angle with TKN [degrees] 2 Mass moment of inertia [kgmm ] Max. speed [rpm] 150 300 320 1700 48 12.30 395000 0.44 7200 520 2800 66 12.45 500000 0.57 7300 4000 1) Referring to rated torque TKN 2) With connection housing DF2 3) Referring to upper range value Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 1 KTR-N Sheet: Edition: 49017 EN 4 of 21 3 Technical data DATAFLEX® torque measuring shaft in combination with RADEX®-N Illustration 2: DATAFLEX® with RADEX®-N Table 3: Dimensions and technical data ® Coupling size of DATAFLEX ® Coupling size of RADEX -N 70/3000 90 70/5000 115 90 210 132 330 80 360 520 15 115 265 163 330 100 376 576 23 Dimensions [mm] Dimension d1 / d2 max. Dimension D1 Dimension D2 Dimension L6 Dimension L7 Dimension L8 Dimension Ltotal Dimension E Setscrew [mm] Dimension G M12 Dimension t 25 Tightening torque TA [Nm] 40 ® ® Mechanical data of combination (DATAFLEX with RADEX -N) 2 Mass moment of inertia [kgmm ] 155200 Torsion spring stiffness [Nm/rad] 283000 Weight [kg] 44.7 1) Max. speed [rpm] 4000 M12 30 40 470000 389000 77.6 3400 1) Higher speeds on request. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 2 KTR-N Sheet: Edition: 49017 EN 5 of 21 3 Advice 2.1 General advice Please read through these operating/assembly instructions carefully before you start up the measuring shaft. Please pay special attention to the safety instructions! The operating/assembly instructions are part of your product. Please store them carefully and close to the measuring shaft. The copyright for these operating/assembly instructions remains with KTR. 2.2 Safety and advice symbols STOP ! Warning of potentially explosive atmospheres This symbol indicates notes which may contribute to preventing bodily injuries or serious bodily injuries that may result in death caused by explosion. Warning of personal injury This symbol indicates notes which may contribute to preventing bodily injuries or serious bodily injuries that may result in death. Warning of product damages This symbol indicates notes which may contribute to preventing material or machine damage. General advice This symbol indicates notes which may contribute to preventing adverse results or conditions. 2.3 General hazard warnings STOP With assembly, operation and maintenance of the measuring shaft it has to be made sure that the entire drive train is secured against accidental switch-on. You may be seriously hurt by rotating parts. Please make absolutely sure to read through and observe the following safety indications. All operations on and with the measuring shaft have to be performed taking into account "safety first". Please make sure to switch off the power pack before you perform your work on the measuring shaft. Secure the power pack against accidental switch-on, e. g. by providing warning signs at the place of switch-on or removing the fuse for current supply. Do not reach into the operation area of the measuring shaft as long as it is in operation. Secure the rotating components of the measuring shaft against accidental contact. Please provide for the necessary protection devices and covers. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 2 KTR-N Sheet: Edition: 49017 EN 6 of 21 3 Advice 2.4 Intended use You may only assemble, operate and maintain the measuring shaft if you have carefully read through the operating/assembly instructions and understood them had technical training are authorized by your company The measuring shaft may only be used in accordance with the technical data (see chapter 1). Unauthorized modifications on the measuring shaft are not admissible. We will not assume liability for any damage that may arise. In the interest of further development we reserve the right for technical modifications. ® The DATAFLEX torque measuring shaft described in here corresponds to the technical status at the time of printing of these operating/assembly instructions. 3 Storage, transport and packaging 3.1 Storage ® ® ® The RADEX -N couplings are supplied in preserved condition. Both DATAFLEX and RADEX -N can be stored at a dry and covered place for 6 - 9 months. ! Humid storage rooms are not suitable. Please make sure that condensation is not generated. The best relative air humidity is less than 65 %. 3.2 Transport and packaging ! In order to avoid any injuries and any kind of damage please always make use of proper transport and lifting equipment. The couplings are packed differently each depending on size, number and kind of transport. Unless otherwise contractually agreed, packaging will follow the in-house packaging specifications of KTR. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 7 of 21 3 Assembly The measuring shaft and the couplings are supplied as single pre-assembled component assemblies. Before assembly the measuring shaft has to be inspected for completeness. ® The mounting position of DATAFLEX is variable. The measurement system can be mounted both horizontally and vertically. 4.1 Components of DATAFLEX® torque measuring shaft ® Components of DATAFLEX torque measuring shaft Component Quantity 1 1 Component assembly ® DATAFLEX torque measuring shaft ® Components of RADEX -N coupling Component Quantity Component assembly 2 2 Flange hub 3 2 Lamina set Clamping ring hub with 4 2 clamping ring 5 2 Setscrew DIN EN ISO 4029 Illustration 3: DATAFLEX® 70 torque measuring shaft with RADEX®-N Please consider our operating/assembly instructions KTR-N 47110 additionally when using ® the RADEX -N coupling. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 8 of 21 3 Assembly 4.2 Advice for finish bore STOP The maximum permissible bore diameters d1max and ® d2max (see RADEX -N catalogue) must not be exceeded. If these figures are disregarded, the coupling may tear. Rotating particles may cause danger to life. Hub bores machined by the customer have to observe concentricity or axial runout, respectively (see illustration 4). Please make absolutely sure to observe the figures for Ø d1max and Ø d2max. Carefully align the hubs when the finish bores are drilled. Please provide for a setscrew according to DIN EN ISO 4029 with a cup point or an end plate to fasten the hubs axially. Illustration 4: Concentricity and axial runout 4.3 Displacements - alignment of the torque measuring shaft The displacement figures specified in table 4 provide for sufficient safety to compensate for external influences like, for example, thermal expansion or foundation settling. ! In order to ensure a long service life of the measuring shaft, the shaft ends have to be accurately aligned. Please absolutely observe the displacement figures specified (see table 4). If the figures are exceeded, the measuring shaft with coupling will be damaged. Please note: The displacement figures specified in table 4 are maximum figures which must not arise in parallel. If radial, axial and angular displacement arises at the same time, these values must be reduced (see illustration 6). Please inspect with a dial gauge, ruler or feeler gauge whether the permissible displacement figures specified in table 4 can be observed. Angular displacement Radial displacement Illustration 5: Displacements Axial displacement Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 9 of 21 3 Assembly 4.3 Displacements - alignment of the torque measuring shaft Table 4: Displacement figures DATAFLEX size ® 70/3000 70/5000 RADEX -N size Max. axial displacement Ka [mm] Max. radial displacement Kr [mm] Max. angular displacement Kw 1) [degree] 90 115 2.0 2.8 6.0 6.1 1.0 ® 1) each lamina set Examples of the displacement combinations specified in illustration 6: Illustration 6: Combinations of displacement Example: Kr = 60% Kw = 20% Ka = 20% Ktotal = Ka + Kr + Kw 100% 4.4 Assembly of the hubs We recommend to inspect bores, shaft, keyway and feather key for dimensional accuracy before assembly. 4.5 Assembly of the RADEX®-N clamping ring hubs on the DATAFLEX® torque measuring shaft The power transmission is frictionally engaged. Fit pair of shaft-clamping ring hub is specified with H7/h6. The following process should be observed with the assembly: Please clean and degrease the contact surfaces of the hub bores and the shafts before assembly. ! Oils and greases containing molybdenum disulfide or other high-pressure additives as well as internal lubricants must not be used. Lightly unscrew the clamping scews, shift the clamping ring hub onto the shaft of the measuring shaft and align to dimension L6. Tighten the clamping screws evenly crosswise. Increase the tightening torque stepwise. Repeat this process until the tightening torque specified in table 5 has been achieved with all clamping screws. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 10 of 21 3 Assembly 4.5 Assembly of the RADEX®-N clamping ring hubs on the DATAFLEX® torque measuring shaft Illustration 7: Assembly of clamping ring hubs Illustration 8: Adjusting to dimension L6 Table 5: Tightening torques of clamping screws Coupling size of DATAFLEX ® Coupling size of RADEX -N Screw size Tightening torque TA [Nm] 1) Transmittable torque [Nm] (frictional torque) ® 70/3000 90 M12 120 70/5000 115 M12 120 5160 8370 1) H7/h6 shaft/hub fit 4.6 Assembly of hubs on the driving and driven side Mount the hubs on the shaft of driving and driven side (see illustration 9). The ends of the shafts must not protrude through the hubs. Shift the power packs in axial direction until the dimension L8 is achieved. If the power packs are already firmly assembled, shifting the hubs axially on the shafts allows for adjusting the distance dimension L8. ! On request the hubs can be provided with a bore for setscrews for axial fastening. Please specify in your order. With the assembly please make sure that the distance dimension L8 (see table 3) is observed. Disregarding this advice may cause damage to the measuring shaft (coupling). Illustration 9: Assembly of the hubs on the driving and driven side Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Illustration 10: Adjusting to dimension L8 Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 11 of 21 3 Assembly 4.7 Assembly of lamina sets ! With the assembly please make sure that the lamina sets are installed free from distortion in axial direction. Disregarding this advice may cause damage to the coupling. Insert the lamina sets and the DATAFLEX measuring shaft. ® Hand-tighten the components for the time being, with the fit bolts being assembled displaced from left to right (see illustration 11). Tighten the fit bolts to the tightening torques mentioned in table 6 by means of a suitable torque key. Illustration 11: Assembly of the lamina sets 4.8 Tightening torque of the fit bolts The fit bolts have to be tightened to the tightening torques T A specified in table 6. Table 6: Tightening torques of the fit bolts Coupling size of DATAFLEX ® Coupling size of RADEX -N Screw size Tightening torque TA [Nm] ! ® 70/3000 90 M16 280 70/5000 115 M20 550 Having started up the coupling, the tightening torque of the fit bolts has to be inspected at regular maintenance intervals. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 12 of 21 3 Assembly 4.9 Advice for assembly of the DATAFLEX® torque measuring shaft Fixing the housing ! ! The housing must be protected from rotation. For that purpose there is a thread size M4 at the bottom side. Please make absolutely sure to avoid a rigid fixing of the housing! Opening the housing is not required and may cause damage to the measuring shaft. Degree of protection ® All DATAFLEX measuring shafts type 70 correspond to protection class IP51 according to DIN EN 60529. Maintenance ® The DATAFLEX measuring shaft is maintenance-free. Lubrication or cleaning is not necessary. Calibration The transducer is calibrated when being supplied. We recommend an annual inspection of the calibration. 4.10 Technical description 1. General description ® The measuring shafts type DATAFLEX 70 are provided with wire strain gauges (DMS) the signals of which are transmitted contactless. In addition, a two-channel shaft encoder provides two speed signals shifted by 90 degrees. Each signal has a resolution of 450 periods per revolution. The measuring shaft is connected to the connection housing DF2 via the connection cable which is available as an accessory. The measuring shaft should not be switched on before all connections have been properly connected. After initial switch-on the measuring shaft needs about 5 minutes until the warm-up period is finished and the measurement device has its standard accuracy. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 13 of 21 3 Assembly 4.10 Technical description 2. Connection housing DF2 The connection housing DF2 has 12 screw terminals to connect power supply, display equipment and switches. The torque signal is displayed as proportional direct voltage from 0 … 10 V. For the speed display two square wave signals, one scalable voltage signal and one direction signal are available (for pin configuration see table 7). The button T1 serves for programming and can be bridged externally from GND via the terminal 12 (T1). Table 7: Pin assignment of the connection housing DF2 No. Description 10 11 24V GND 4 5 6 M-U GND M-I 7 N1 8 GND 9 N2 1 R/L 2 3 GND N-U 12 T1 13 14 15 L1, L2 T1, T2 TP 16 - 17 - Function Features Input operating voltage Supply voltage + 24V DC ± 4V / 100 mA Supply voltage Torque output Output voltage + -10V ... 10V (RA = 1 k) Ground torque output Without function Speed output pulse signal Speed output HTL (24V, 450 pulses/rev.) channel 1 TTL (5V, 450 pulses/rev.) Ground for pulse speed output Speed output HTL (24V, 450 pulses/rev.) channel 2 TTL (5V, 450 pulses/rev.) Speed output DC-voltage HTL (24V, clockwise = 0) Direction signal speed TTL (5V, clockwise = 0) Ground for DC speed output Speed of DC voltage output 0 V ... 10 V (scalable) Other connections / operating devices External push button Push button T1 connection T1 Signal LEDs Push button T1, T2 Push button for programming Switch low pass filter On/off switch low-pass Connection of measuring 1:1 Connection cable shaft Switch for speed scaling see table 11 Illustration 12: Connection housing DF2 3. Description of connections a) Supply voltage 24V (No. 10 and 11) The supply voltage is 24V ± 4V direct current voltage (DC). The current consumption is 100 mA at the maximum. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 14 of 21 3 Assembly 4.10 Technical description b) Torque signal M-U (No. 4 and 5) The output voltage is proportional to the torque with an output of values between -10V and 10V. Table 8 shows the relation between torque and output voltage. Table 8: Assignment of torque - output values ® DATAFLEX size 70/3000 70/5000 M / V 300 Nm / V 500 Nm / V Illustration 13: Assignment of torque - output values c) Filter voltage output (No. 15) The torque signal may be filtered by activating a low-pass filter so that high-frequency parts of the signal are eliminated. Table 9: Low pass button (No. 15) Switch position TP Left Low pass on Right Low pass off The limit frequency of the filter can be changed by varying the DIP switches (see illustration 14) inside the connection housing: Illustration 14: Location of DIP switch Table 10: Adjustment of the requested filter frequency Limit frequency [Hz] Switch 1 OFF 2000 ON 1000 100 OFF 10 OFF 1 OFF A filter frequency of 1000 Hz is preset. Please observe protection note ISO 16016. Drawn: Verified: Switch 2 OFF OFF ON OFF OFF 2017-01-02 Shg/Koe 2017-01-02 Shg Switch 3 OFF OFF OFF ON OFF Replacing: Replaced by: Switch 4 OFF OFF OFF OFF ON KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 15 of 21 3 Assembly 4.10 Technical description d) Speed signals N1, N2, N-U, R/L (No. 1, 3, 7, 9) The connection housing DF2 has 4 connections for speed output: - Two square-wave signals shifted by 90 degrees (N1, N2) A scalable voltage output (N-U) with direction signal (R/L) Illustration 15 Outputs N1 and N2 Each of the speed outputs N1 and N2 provide a square-wave signal with a resolution of 2x450 periods per revolution (illustration 16). Illustration 16 The speed is calculated as follows: N [rpm] = f [Hz] / 7.5 The speed channel signals N1 and N2 have a phase shift of 90 degrees to each other. Depending on the rotational direction one of the two signals leads 90° in phase (illustration 17). Clockwise Illustration 17 Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 16 of 21 3 Assembly 4.10 Technical description Output circuit (connection N1 and N2) The speed outputs N1 and N2 have short-circuit proof pushpull outputs providing a square-wave voltage with an amplitude of 24V and a maximum switching current of 30 mA. The output terminals must not be charged with an external voltage (see illustration 18). The output voltage of speed lines and torsional direction line can be varied by modifying the jumper position in the connection housing to 5V level (see illustration 19). Illustration 18: Output circuit of speed outputs Illustration 19: Modification of voltage level for the speed signal/direction signal Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 17 of 21 3 Assembly 4.10 Technical description Outputs N-U and R/L The KTR connection housing DF02 has an integrated f/U converter which converts the square wave signals of the encoder into a linear DC voltage output (terminal N-U) and generates an additional signal for the rotational direction (terminal R/L). On the bottom side of the connection housing DF02 there is a sixfold multiple switch allowing to adapt the scaling of the speed signal to the type of measuring shaft and the speed range (see illustration 12 and 20). Illustration 20: Switch positions Scaling of the speed direct voltage output Table 11: Switch position S1-S4 and the corresponding scale of the speed output N-U Max. speed 10 20 40 60 80 100 200 400 600 800 1000 2000 4000 6000 8000 10000 Scaling 1 rpm / V 2 rpm / V 4 rpm / V 6 rpm / V 8 rpm / V 10 rpm / V 20 rpm / V 40 rpm / V 60 rpm / V 80 rpm / V 100 rpm / V 200 rpm / V 400 rpm / V 600 rpm / V 800 rpm / V 1000 rpm / V S1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 S2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 S3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 S4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Illustration 21 ® Table 12: Selection of DATAFLEX series ® DATAFLEX type ® DATAFLEX 22, 42, 85, 140 ® DATAFLEX 16 ® DATAFLEX 32, 42 (red) ® DATAFLEX 70 S5 0 1 0 1 S6 0 1 1 0 Table 13: Direction signal Output voltage R/L 0 24V * Torsional direction Clockwise Counter-clockwise The signal of the speed direction output R/L shows the rotational direction (see table 13). Switching between 5V and 24V possible (see illustration 19 Modification of voltage level for the speed signal/direction signal) Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 18 of 21 3 Assembly 4.10 Technical description e) Control buttons and LEDs (No. 12 to 14 and illustration 22) The connection housing DF02 has control switches and LEDs for offset adjustment and sensor test. For reasons of safety the sensor test can only be performed during the first 15 seconds after switching on. The zero adjustment can be performed after a turn-on period of 15 seconds (illustration 22). The termination of the 15 seconds period is signalized by a short blinking of the LEDs of the connection housing. Illustration 22 Automatic zero adjustment (illustration 23) If the „push button“ T1 is activated for a period of 2 seconds, the output of the torque signal is automatically set to 0 Volt. The adjusting is effected irrespective of the amount of the actual torque. The termination of the adjustment is confirmed by fast blinking of the LED L1. The new zero point has been saved and the device is in the measuring mode again. The automatic zero adjustment can only be performed if the measuring shaft is switched on for more than 15 seconds. If necessary, the automatic zero adjustment can be performed by an external control, too. If the potential of the terminal clamp T1 is connected with GND for 2 seconds, an automatic zero adjustment is performed. Illustration 23: Automatic zero adjustment Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 4 KTR-N Sheet: Edition: 49017 EN 19 of 21 3 Assembly 4.10 Technical description Manual zero adjustment The zero point of the torque output can be adjusted manually. For this purpose both push buttons T1 and T2 are activated simultaneously for 2 seconds. The LED L1 is blinking four times. Pressing the push button T1 increases the voltage, pressing the push button T2 decreases the voltage. The modifications are accelerated if the corresponding push button is pressed permanently. Each amendment is confirmed by short blinking of the LED L2. Having performed the adjusting the new values are stored lastingly by pressing both push buttons again for 2 seconds. The LED L1 is illuminated once and signalizes the return to the measuring mode. The manual zero adjustment can only be performed if the measuring shaft is switched on for more than 15 seconds and the signal has levelled off. Illustration 24: Manual zero adjustment Sensor test During the first 15 seconds after powering up the torque sensor can be inspected for operativeness. If the push button T2 is pressed for 2 seconds the torque voltage output will be increased by approx. 4 Volt for the period of 2 seconds. The sensor test can only be performed during the first 15 seconds after switching on. Illustration 25: Sensor test Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 5 KTR-N Sheet: Edition: 49017 EN 20 of 21 3 Disposal In respect of environmental protection we would ask you to dispose of the packaging or products on termination of their service life in accordance with the legal regulations and standards that apply, respectively. 6 Maintenance and service ® DATAFLEX is a low-maintenance torque measuring shaft. We recommend to perform a visual inspection on the torque measuring shaft at least once a year. Please pay special attention to the condition, alignment and screw ® connection of the torque measuring shaft and the condition of the lamina sets of the RADEX -N coupling. Having started up the torque measuring shaft the tightening torques of the screws have to be inspected during the usual inspection intervals. ! 7 Please consider our operating/assembly instructions KTR-N 47110 additionally when using ® the RADEX -N coupling. Services, customer service addresses If requested, we are pleased to perform the calibration of your torque measuring shaft and other services. Contact addresses of the KTR partners for spare parts and orders can be obtained from the KTR homepage at www.ktr.com. KTR does not assume any liability or warranty for the use of spare parts and accessories which are not provided by KTR and for the damages which may incur as a result. Please observe protection note ISO 16016. Drawn: Verified: 2017-01-02 Shg/Koe 2017-01-02 Shg Replacing: Replaced by: KTR-N dated 2017-01-02 DATAFLEX® 70/... Torque Measuring Shaft Operating/Assembly instructions 8 KTR-N Sheet: Edition: 49017 EN 21 of 21 3 EC Certificate of conformity EC Certificate of conformity The manufacturer - KTR Systems GmbH, D-48432 Rheine - states that the DATAFLEX® torque measuring shaft described in the present operating/assembly instructions is in accordance with the following directive: 2014/30/EU Directive of the European Parliament and European Council dated February 26. 2014 for harmonizing the legal provisions of the member states regarding electromagnetic compatibility Standards applied: DIN EN 61000-6-2: DIN EN 61000-4-2: DIN EN 61000-4-3: DIN EN 61000-4-4: DIN EN 61000-4-6: DIN EN 61000-6-4: DIN EN 55011: Rheine, Place Interference immunity for industrial environments Electrostatic discharge immunity test (ESD) Radiated, radio-frequency, electromagnetic field immunity test Electrical fast transient/burst immunity test Immunity to conducted disturbances, induced by radio-frequency fields Emission for industrial environments Intensity of radio interference area (class B) 2017-01-02 Date Please observe protection note ISO 16016. Drawn: Verified: i. V. Reinhard Wibbeling Engineering/R&D 2017-01-02 Shg/Koe 2017-01-02 Shg i. A. Jürgen Kösters Product Manager Replacing: Replaced by: KTR-N dated 2017-01-02 ">

Public link updated
The public link to your chat has been updated.
Advertisement