TEXONIC RX 1200 Owner's Manual

Add to My manuals
30 Pages

advertisement

TEXONIC RX 1200 Owner's Manual | Manualzz
RX 1200
6 SOURCE/6 Z0NE
Audio Distribution Amplifier
(2 x Streamer Inside)
RX1200
SOURCE INPUTS
Link
3
Link
4
OWNERS MANUAL
2
INTRODUCTION
The RX 1200 home audio system brings you the advanced Generation D
technology, it is a functional, easy-to-install, highly compatible, expandable
and used-friendly audio distribution system. With few simple steps to install, it
provides up to 50Wx2 power by class D amplifier and distribute at most to 18
zones which all can be controlled by packaged keypads, IR remote controller
or APP.
Simply connecting the RX 1200 to the local Ethernet network, it let you access
a wide variety of music from the Built-in streaming services or stored on the
Smartphones. Two USB ports on the front panel for playing music files from
USB storage devices. An Optical digital input to manage the sound of a flat
screen or a CD player to have high resolution of sound quality in each zone.
The overall distribution system including package device is easy-to-install, so
every audiophile in every zone can use IR controller or keypads to enjoy the
powerful audio. High functionality and performance bring you musical
enjoyment just the way you want it.
FEATURE
*Each zone provides 50Wx2 (@ 4 Ohm) output power.
*High efficiency more than 85% Class D amplification.
*6 Line input sources, including 2 Audio Streamers (Input 3, 4).
*USB ports for playing music files from USB Flash Drive (Input 3, 4).
*Each zone Stereo/Mono output selectable.
*Enable control over Ethernet.
*Support Control APP.
*PRE-AMP output on Zone1~6.
*Built-in IR receiver & IR remote controller for Source
select/Volume/Treble/Bass.
*12V DC trigger output to external device when the system is power on.
*12V DC mute trigger input from the external devices.
*RJ45 Ethernet port for the wired connection to the local network.
*Another RJ45 Ethernet expansion port for connecting with smart TV or other
device.
*RS-232 port allows 2-way communication with the Home Automation system.
*Expandable up to 18 Zones by additional 2 units.
*6 LEDs for 6 zones Power On, Standby and Mute.
*Built in IR emitter.
*AC 115V / 230V input power switchable.
3
SPECIFICATION
Output Power:
Output Power:
Output Power:
S/N:
THD:
Frequency Response:
Input Impedance:
Input Sensitivity:
Protection Function:
System on Voltage:
External Mute Voltage:
Power Supply:
Output Connection:
Input Connection:
Sampling Rate(Streamer):
Audio Format(USB):
Streamer Support:
USB type:
Network:
Dimension:
Weight:
25W x 2 per zone (at 8Ω)
50W x 2 per zone (at 4Ω)
100W per zone (Bridged at 8Ω)
>85dB A WTD
<0.1%
20Hz-20KHz
>47 K Ohm
250 mV
Overload, Short Circuit
DC +12V
DC +12V
AC115V/60Hz, 230V/50Hz
4P Terminal Block
Input 1, 2 - RCA Jacks
Input 3, 4 – Streamers or USB ports
Input 5 – 3.5mm Jack
Input 6 – S/PDIF, 3.5mm Jack
24Bit / 48KHz
MP3/WMA/AAC/AAC+/ALAC/FLAC/APE/WAV
DLNA, AirPlay
USB2.0, Support up to 64G.
RJ45, Standard 10/100Mb
430mm x 89mm x 416 mm (WxHxD)
12KG
FRONT PANEL
RX1200
SOURCE INPUTS
Link
1
4
2
3
Link
3
4
1. Power ON/OFF/ STANDBY
Depress the power button to turn
on the system. Press it again to
release the latch and power the
unit off. Note that even the Master
Controller is powered on, each
zone will remain in Standby mode
until the zone keypad is activated.
2. Standby/Zone ON LED
These six LEDs illuminate to indicate the
status of each zone.
Blue: In Standby mode.White: In Activate
mode.Blue/White: In Mute mode.
3. USB Port 3/4
Two USB ports correspond to the built-in
Wi-Fi Streamers, as source input 3 and 4.
Playing audio source from USB Flash
Drives.
REAR PANEL
1 3
5
2
1. PRE-AMP OUTPUT
Stereo Line level output on each zone.
Connect to additional amplifier with higher
output, or powered Sub-woofers.
2.SPEAKER OUTPUTS
6 x Removable terminal block connectors
on each zone.
Each zone provides 2x50W @ 4 Ohm or
100W @ 8 Ohm in bridge mode.
4
6
10 12 11
7
8 9 13 14 15
16
17
6.STATUS
When the zone is activated, the corresponding
jack will output 12VDC to trigger other device.
7.IR EMITTERS
IR Outputs 6 routed & 1 common
8.PA-IN
12VDC paging trigger input
9.EXT. MUTE/CONTROL OUT
Mute the entire system with the 12VDC MUTE IN.
3.STEREO/BRIDGE SWITCH
4.SOURCE INPUTS
6 Stereo Analog/Digital inputs.
Use the12VDC CONTROL OUT to trigger other
equipment
10.EXPANSION IN/OUT PORT
Two Wi-Fi Streamers are input 3 and 4.
5.Input 1/PA
Paging capability for Input 1 to broadcast
Expandable to 18 zones with 3 x Multi-zone
Controller systems.
11.ETHERNET PORTS
to all zones when 12VDC is applied to the
PA - IN jack.
Dual LAN ports, one connects to the LAN port of
local router. Another connects to network TV or
other device which requires Ethernet.
5
12.ETHERNET/RS232 SWITCH
ETHERNET: When the amplifier connects to
Ethernet.
Set the unit ID when connecting multi
Controller systems
15.KEYPAD
RS232: When the amplifier control by PC or
Control Device via RS-232.
13.AGC
RJ-45 jack Connects to the keypad hub
for 6 keypads.
16.VOLTAGE SELECT
Automatic Gain Control, brings low level up
to a present-level.
14.MASTER/SLAVE SWITCH
Please set to correctly input voltage
before turn on the amplifier.
17.AC INPUT
1
2
4
7
6
3
5
6
7
2
1
5
6
7
3
3
4
7
RX 1200
RX 1200
RCA
8
3.5mm Stereo
The RX 1200 can work with speakers that are 4-8 Ohm. There are 9 two
modes that can be set for different setups: Stereo or Bridge. An 8 Ohm
speaker can only be used when in Bridge mode. To choose between modes,
use the mode switch to determine modes for each zone (Number 2 Panel
Descriptions, page 5)
STEREO MODE
STEREO MODE
and network.
9
The MAP-1200US comes with 6 POE enabled keypads. This allows for source
control from each specific zone as well as IR routing to the appropriate source
devices once selected. The MAP-1200US also comes with a hub that allows for all
6-keypads to be connected to the amp via Cat5e/6.
ZONE-1
ZONE-2
ZONE-3
ON ON OFF
ON OFF ON
ON OFF OFF
1
2
3
ZONE-4
OFF ON ON
1
10
2
3
1
2
3
1
2
3
ZONE-5
ZONE-6
OFF ON OFF
OFF OFF ON
1
2
3
1
2
3
reserved for cascading units
FRONT
BACK
12VDC out to trigger
external amplifier
RX 1200
11
12
When being used with keypads, the RX 1200 can receive IR signals from each
zone, and routed back through the Cat5e/6 and Keypad up to the Amplifier to
control the selected source. For example, if Source 2-DVD is selected in Zone 1,
the user will be able to control the DVD player to power the device on/off,
change settings ect. Since the amplifer has discreet routing, ONLY the Source
that is selected on each zone can be controlled. This prevents other sources
from accidently be controlled when selected on other zones.
Source 2-DVD
IR Emitter from
Source 2 port
Power
IR Signal
Grounding
IR +
IR -
The RX 1200can allow 6 sources to be distributed to up to 18 zones on 3
different units using the provided ribbon cable to connect between units. To do
this first each unit needs to be addressed according using the MASTER/SLAVE
switch. There are 3 positions for this, Master, Slave 1, and Slave 2 which help
identify each unit.
13
Master
SLAVE 1
SLAVE 2
14
ETHERNET CONNECTION
Network TV
Router
APP
EXPANSION
VOLTAGE SELECT
Reset
ETHERNET
INPUT
115V
230V
AC: 115V ~ 60Hz, 1250W FUSE: T10AL 250V
AC: 230V-240V ~ 50Hz, 1250W FUSE: T5AL 250V
RS232
PA
EXT.MUTE
KEYPADS
There are two RJ-45 jacks on the rear panel of this amplifier for the connection to
Ethernet.
Please use a good quality Cat5e/5 cable, and follow the connecting diagram
below.
1.Connect the LAN1 port on the rear panel of controller to the local Wi-Fi Router.
The Ethernet connection mainly for Wi-Fi control via APP or other control devices.
2.Connect the LAN2 port on the rear panel of control to the smart TV or other
Network devices.
The port simply works as SWITCH function as long as the LAN1 port enabled to
Ethernet.
Note: When controlling via ETHERNET, please make sure the ETHERNET/RS232
switch is set at ETHERNET position.
15
CONNECTION DIAGRAM
Stereo Amplifier
Powered
Subwoofer
or
Network TV
MAP-1200HD
Router
APP
PRE-AMP OUTPUT
PRE-AMP OUTPUT
PRE-AMP OUTPUT
PRE-AMP OUTPUT
PRE-AMP OUTPUT
EXPANSION
SOURCE INPUTS
PRE-AMP OUTPUT
L
L
L
L
L
L
L
R
R
R
R
R
R
R
VOLTAGE SELECT
5
Reset
ETHERNET
OUTPUT
INPUT
YES NO
YES NO
BRIDGE
YES NO
BRIDGE
YES NO
BRIDGE
YES NO
BRIDGE
115V
YES NO
BRIDGE
BRIDGE
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
SPEAKER-OUTPUT
SPEAKER-OUTPUT
SPEAKER-OUTPUT
SPEAKER-OUTPUT
SPEAKER-OUTPUT
SPEAKER-OUTPUT
1 / PA
ZONE 1
2
ZONE 2
6
ZONE 3
SOURCE 1
RS232
SOURCE 2
SOURCE 3
PA
EXT.MUTE
KEYPADS
SLAVE 1
AGC
ZONE 4
R
Bridge 8Ω
4/8Ω
4/8Ω
L
R
Bridge 8Ω
4/8Ω
4/8Ω
L
R
Bridge 8Ω
4/8Ω
4/8Ω
L
R
Bridge 8Ω
4/8Ω
4/8Ω
L
R
Bridge 8Ω
4/8Ω
4/8Ω
L
R
Bridge 8Ω
4/8Ω
4/8Ω
L
ZONE 5
ZONE 6
SOURCE 4
STATUS
12V Trigger
output
DVD
16
230V
AC: 115V ~ 60Hz, 1250W FUSE: T10AL 250V
AC: 230V-240V ~ 50Hz, 1250W FUSE: T5AL 250V
SOURCE 5
SOURCE 6
IR EMITTERS
ALL
CONTROL
OUT
SYSTEM
YES / NO
SLAVE 2
MASTER
INTEGRATED NETWORK
The controller and APP are easy to install and connect to the local network,
simply connect the RJ-45 IN port to the router via Cat5 cable, and also make
sure your smart devices connect to the same local network. After connecting the
controller to the router by Cat5 cable, the controller will connect with the local
network automatically.
In case, having the problem for connecting to the network, please check the
position of switches on the rear panel.
Please switch to MASTER and ETHERNET.
Note. Please do not press “Reset” button.
Note. Please do not connect the Ethernet port of RX 1200 to the computer
directly.
1.Open the IE web browser of PC, log in to the WEB configuration page of local
Router to find the IP address of RX 1200 (shown as below)
RX 1200
17
2. Using “Advanced_IP_Scanner” software to find the IP address.
Please visit www.advanced-ip-scanner.com for free download.
Then enter the IP address of RX 1200 to the IE browser (shown as below), ensure
the Serial Configure is 9600,n,8,1. After finishing this step, MAP-1200US could be
controlled through the local Network.
18
Download free software “PuTTY” Tool from the internet to control the device.
Operation diagram as below:
19
Click Telnet, enter the IP address of RX 1200 and port: 8080.
Click Open.
When the IP address connected, the operation diagram shows as below:
Key in the command code to control RX 1200.
For the detail of command codes, please find the RS-232 command codes in this
instruction manual.
20
RS232 CONTROL
The RX 1200 provides an RS-232 serial port connection located on the back
panel and uses a USB-to- Serial Comm cable connection. The RX 1200 supports
bi-directional RS-232 communication with third party automation systems. All
keypad and remote control operations can be controlled via RS-232 in addition
to system expansion up to 18 zones or 3 RX 1200 units linked together using the
included 18 pin expansion cable.
Note: Set the switch to RS232 position.
Baud Rate 9600, 8, N, 1 , DB9 Connector Pin out, Tx, Rx, GND
Using free software “PuTTY” Tool to control the device. Operation diagram as
below:
21
Click Serial, check the COM port and enter the Baud rate 9600.
Click Open.
Note: To find the information for the COM port, please open the device manager
of the computer, shown as below:
When the IP address connected, the operation diagram shows as below:
Key in the command code to control RX 1200
22
RX 1200 RS-232 CONTROL CODES
(Baud Rate: 9600,8,N,1 , DB9 Connector Pin out, Tx, Rx, GND)
'CR':Carriage Return (0x0D)
Not case sensitive
Control Command Structure <xxPPuu'CR'
Reply Control Command Structure >xxPPuu'CR'
xx: Represent control command code
10 :All zones of host computer 1
20 :All zones of host computer 2
30 :All zones of host computer3
11 : Zone1 of host computer 1
12 : Zone2 of host computer 1
13 : Zone3 of host computer 1
...............
PP: Represent Control action code
PR:Power control
PR00:Power off
PR01:Power on
MU:Mute control
MU00:Mute off
MU01:Mute on
DT:Do Not Disturb control
DT00:DT control off
DT01:DT control on
VO:Volume control
VO(00-38):Volume control
TR:Treble control
TR(00-14):Treble control
BS:Bass control
BS(00-14):Bass control
BL:Balance control
BL(00-20):Balance control
CH:Source Channel control
CH(01-06):Source control
Ask command structure(1) ?xx'CR'
xx: Represent control command code
10 :All Zones of host computer 1
20 :All Zones of host computer 2
23
30 :All Zones of host computer 3
11 :Zone1 of host computer1
12 :Zone2 of host computer1
13 : Zone3 of host computer1
21 : Zone1 of host computer2
22 : Zone2 of host computer2
23 : Zone3 of host computer2
...............
Reply Command: >xxaabbccddeeffgghhiijj'CR'
aa:PA Control status
bb:Power Control status ([5]:Backup Zone Power Status (only on zone)
cc:Mute Control status
dd:DT Control status
ee:Volume Control status
ff:Treble Control status
gg:Bass Control status
hh:Balance Control status
ii:Source Control status
jj:The connection status of line control(00:unconnected 01:connected)
Ask command structure (2) ?xxPP'CR'
xx: Control Command Structure
10 :All Zones of host computer 1
20 :All Zones of host computer 2
30 :All Zones of host computer 3
11 : Zone1 of host computer 1
12 : Zone2 of host computer 1
13 : Zone3 of host computer 1
14 : Zone4 of host computer 1
15 : Zone5 of host computer 1
16 : Zone6 of host computer 1
...............
PP: Represent Control action code
PA:PA Control
PR:Power Control
MU:Mute Control
DT:DT Control
VO:Volume Control
TR:Treble Control
BS:Bass Control
24
BL:Balance Control
CH:Source Control
LS: The connection status of line control
Reply command: >xxPPuu'CR'
Enter1<********'CR' Change Source 1 display name;********It must be 8 effective
ASCII code
Enter2<********'CR' Change Source 2 display name
Enter 3<********'CR' Change Source 3 display name
Enter 4<********'CR' Change Source 4 display name
Enter 5<********'CR' Change Source 5 display name
Enter 6<********'CR' Change Source 6 display name
Enter M<********'CR' Change display name of connect control when it starts
Enter <9600'CR' Change RS232 to rate 9600
Enter <19200'CR' Change RS232 to rate 19200
Enter <38400'CR' Change RS232 to rate 38400
Enter <57600'CR' Change RS232 to rate 57600
Enter <115200'CR' Change RS232 to rate 115200
Enter <230400'CR' Change RS232 to rate 230400
When unplugging and re-plugging the AC power cord, the
Baud speed rate will return to 9600.
REPRESENT OF CONTROL ACTION CODE
Symbol
Master、Slave1、Slave2
Zone
<
<
<
<
<
<
<
1、2、3
1、2、3
1、2、3
1、2、3
1、2、3
1、2、3
1、2、3
1~6
1~6
1~6
1~6
1~6
1~6
1~6
Controlactioncode ControlRange
PR(POWER)
MU(MUTE)
CH(SOURCE)
VO(VOLUME)
TR(TREBLE)
BS(BASS)
BL(BALANCE)
(00-01)
(00-01)
(01-06)
(00-38)
(00-14)
(00-14)
(00-20)
25
EXAMPLES OF RS-232 COMMAND CODE
AllZoneON
<10PR01
Zone1ON
<11PR01
AllZoneOFF
<10PR00
Salve1/Zone1OFF
<21PR00
AllZoneMuteON
<10MU01
Zone6MuteON
<16MU01
AllZoneMuteOFF
<10MU00
Salve2/Zone5MuteOFF
<35MU00
AllZoneSource01
<10CH01
Zone1Source01
<11CH01
AllZoneSource06
<10CH06
Zone6Source06
<16CH06
AllZoneVolume00
<10VO00
Zone1Volume00
<11VO00
AllZoneVolume38
<10VO38
Zone6Volume38
<16VO38
AllZoneTreble(-7)
<10TR00
Zone1Treble(-7)
<11TR00
AllZoneTreble(0)
<10TR07
Zone1Treble(0)
<11TR07
AllZoneTreble(7)
<10TR14
Zone1Treble(7)
<11TR14
AllZoneBass(-7)
<10BS00
Zone6Bass(-7)
<16BS00
AllZoneBass(0)
<10BS07
Zone6Bass(0)
<16BS07
AllZoneBass(7)
<10BS14
Zone3Bass(7)
<13BS14
AllZoneBalance(atLeftCH)
<10BL00
Zone1Balance(atLeftCH)
<11BL00
AllZoneBalance(atMiddle)
<10BL10
Zone1Balance(atMiddle)
<11BL10
AllZoneBalance(atRightCH)
<10BL20
Zone1Balance(atRightCH)
<11BL20
InquiryMasterAllZoneStatus
?10
InquirySlave1AllZoneStatus
?20
26
INQUIRY COMMAND STRUCTURE
Symbol
Master、Salve1、Salve2
Zone
?
1、2、3
1~6
InquiryMasterAllZoneStatus
?10
InquirySlave1AllZoneStatus
?20
InquirySlave2AllZoneStatus
?30
REPLY COMMAND
>xxaabbccddeeffgghhiijj
xx:Unit/Zone
>1100000000200707100100
aa:PAINStatus
bb:PowerStatus
cc:MuteStatus
dd:DTStatus
ee:VolumeStatus
ff:TrebleStatus
gg:BassStatus
hh:BalanceStatus
ii:SourceStatus
jj:KeypadConnectionStatus(00:Unconnected,01:Connected)
27
APP QUICK START
Download the control APP:
1. The control APP is available for Apple iPhone/iPad and Android smart phone/Pad,
2. Please search “MRX 1200” on Google Play / App Store to download.
3. Download and install the APP
Note. This APP is applied to TEXONIC controller and Multi-Room amplifiers
28
APP QUICK START – FUNCTION INSTRUCTION
1. Output Zone Selection
(Press and hold the button to change the zone name)
2. Input Source Selection
Press and select the input source. The name of input source could be changed.
3. Treble/Bass/Balance
4. Volume for individual zone
5. Mute for individual zone
6. Power ON/OFF for individual zone
7. All Zones ON
8. All Zones OFF
9. Party mode
All zones will be synchronize and controlled from the specific zone.
10.Settings and Connection
Please read the instruction in next page for properly connection.
11.Streamer icon
Press this icon to open the streamer APP.
29
APP QUICK START – SETTINGS AND CONNECTION
1. Mobile phone IP address
When the smart phone or Pad is connected to local network, the IP will automatically
show on this area.
2. AUTO
Press AUTO to search the device IP.
3. Device IP address
When the IP is found, the APP will connect to the device automatically.
4. Manually Enter
Manually enter the device IP to connect to the device.
5. MASTER/SLAVE Selection
When the MASTER amplifier connecting with additional SLAVE1/SLAVE2 amplifiers,
press one of these buttons to determine which amplifier will be controlled.
6. 6 Zones/4 Zones Selection
Select 6 Zones or 4 Zones for corresponding MASTER/SLAVE1/SLAVE2 amplifier.
Note: MAP-1200PRE is 6 zone controller.
30

advertisement

Related manuals

Download PDF

advertisement