US10 Series Installation Guide

US10 Series Installation Guide
US10 Series Installation Guide
Version: 1.0
Date:Nov.2010
US10 Serial Installation Guide
About this Guide:
This guide mainly introduces the installation instructions and the wiring
method of US10 series device.
Our products are subject to update from time to time, so our
company will neither make a commitment to guarantee the consistency
between the actual products and this document, nor assume any
responsibility for any dispute arising out of the discrepancy between the
actual technical parameters and this manual. This document is subject
to change without prior notice.
II
Table of Contents
Table of Contents
1. Notice about Installing .................................................... 1
2. Device Overview .............................................................. 3
2.1 System Construction .................................................................... 3
2.1 Device Interface............................................................................ 4
3. Device Installation and Wiring ....................................... 5
3.1 Device Installation ........................................................................ 5
3.2 Communication Connection ......................................................... 5
3.2.1 Ethernet Mode ....................................................................... 5
3.2.2 RS232 Mode .......................................................................... 6
3.3 External Ring and the Lock Connection ★.................................... 8
3.4 Printer Connection ........................................................................ 9
3.5 Power Connection .......................................................................11
4. Test and Examine after Installation.............................. 12
5. Other Functions ............................................................ 13
5.1 USB Port .................................................................................... 13
5.2 Reset Function ........................................................................... 13
5.3 Card Reader ............................................................................... 14
5.3.1 Barcode Card Reader .......................................................... 14
5.3.2 Magnetic Stripe Card reader ................................................ 14
5.4 WiFi Connection ★ ..................................................................... 15
6. Trouble Shooting ........................................................... 16
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
1. Notice about Installing
This is a mass-produced product. It strictly follows to the criteria of
manufacture and inspection of China, U.S.A, and EU. Here we recommend
you to read this file carefully, for using the device properly can obtain the best
efficiency and speed. Otherwise, the incorrect installation may cause the unit
damage. Although we could do our best to offer you service, but this could
cause unwanted cost for you.
1. Before installation, please make sure the power is cut off, because it is
very dangerous if the power is on. The accidentally contact of power cable
may cause the core parts damage.
2. Power cable is connected after all the other wiring. If the device is
working abnormally, please shut down the power first, then make the
necessary check. Kindly reminds you that any hot-line work may damage the
device, and operations will not under warranty.
3. The height to mount device is about 1.4-1.5 meter
4. Our equipment offers an auto test function. After the installing, please run the
auto-test function to confirm the installation is finished.
5. In order to guarantee the device run for long time, we set an auto-sleep and
wake up function by default, please carefully examine this function normally
setting before using.
6. We recommend using the equipped DC12V power supply for the
device. If the parameters of the power surpass this scope, or the power
supply has the bad quality, it possibly causes the damage to the device, and
it will not under the warranty.
1
US10 Serial Installation Guide
7. Before the device to be connected please read and always follow this
guide closely. Because the wrong wiring will cause the core board to burn
out, insult in device to break down, at this situation we are not liable for any
damages and troubles.
8. If the distance between the power and device is too long, please do not
use the twisted-pair or other type cable for the power wire. When the power
wire is selected, you should consider attenuation of voltage which has
passed long distance transfer.
For other not details items please see to the user manual and so on.
2
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
2. Device Overview
2.1 System Construction
1. External Ring ★: Connect the electrical bell to the device, when
arrive the appointed time, the device will send a signal to trigger the relay.
2. Unlock ★: After the user verified the identity, the device will output the
unlock signal and unlock the door.
3. Supports RS232, TCP/IP modes to connect with PC, that enable you
to manage multiple devices easily.

Note: The external ring and unlock function are both optional functions
and they can not use together. If you need to use any one of them, please
contact our business representative or technical support.
3
US10 Serial Installation Guide
2.1 Device Interface
Back View:
Power Supply
Ethernet Port
Wiring Terminals

Power Supply: Use to connect with the power supply.

Ethernet Port: Connect the device into the Internet or connect with
the PC directly.

Wiring Terminals: Use to connect with the external ring (or door
lock), RS232 communication (or connect with the printer). See to the red
circle on the above figure. The magnified picture as below.
Device Interface:
 Note: You can not use RS232 communication and connect the printer at
the same time.
4
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
3. Device Installation and Wiring
3.1 Device Installation

Note: Do not connect peripheral equipment before the power of the
device is cut down, otherwise it is possible to damage the device badly.
Please read and always follow this guide strictly at wiring process.
The device installation operations are as follows:
1. Determine the position of the device installation on the wall. The
device should be mounted on the external wall of the door, and about 1.4
meters from the ground.
2. Stick the mounting paper on the determined position, drill four screw
holes and one wiring hole follow the illustration of the template.
3. Use the screws to fix the plate on the wall, and then fix the device on
the plate.
4. After installation, please make sure the device is reliable, fasten, and
stable.
3.2 Communication Connection
There are two ways that the PC software communicate and exchange
information with the device: RS232 and TCP/IP.
3.2.1 Ethernet Mode
1. Connects with PC through cross cable, as the figure 3-1.
5
US10 Serial Installation Guide
Figure 3-1
2. The device and the PC both connected to LAN/WAN through
Switch/LAN switch as figure 3-2.
Figure 3-2
3.2.2 RS232 Mode
We will provide a RS232 cable with the device. Connect the device with
the PC serial port through this cable, as figure 3-3.
6
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
Figure 3-3
Only four terminals are used for RS232 communication: SGND, RXD,
TXD, and GND. Plug the DB 9 PIN side of the cable into the PC port, the
other side plug into the device terminals, as figure below.
Device Terminals
Terminal
PC 9 PIN
Port Number Definitions
TXD--------------------------------------------------2
RXD
RXD--------------------------------------------------3
TXD
SGND------------------------------------------------5
GND
GND--------------------------------------------------Shield Terminal
7
US10 Serial Installation Guide
3.3 External Ring and the Lock Connection ★

Note: The external ring and unlock function are both optional functions
and they can not use together. If you need to use any one of them, please
contact our business representative or technical support.
1. Electric lock connection:
After the user verified the identity, the device will output the unlock signal.
The device supports NO LOCK and NC LOCK. For example the NO LOCK
(normally open at power on) is connected with “NO” terminal, and the NC
LOCK is connected with “NC” terminal.
Normally Closed Lock:
The lock is normally closed at power on, the connection as figure 3-4.
Figure 3-4
Normally Open Lock:
The lock is normally open at power on, the connection as figure 3-5.
8
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
Figure 3-5
2. External Ring:
Connect the electrical bell to the device, when arrive the appointed time,
the device will send a signal to trigger the relay. The connection please refers
to the figure 3-6.
Figure 3-6
3.4 Printer Connection
This function is designed for a serial port printer only, the parallel printer
9
US10 Serial Installation Guide
is unavailable. After a user is verified, the result will be sending out through
serial port. If the device is connected with the printer, the result can be
printed directly. We will provide a 25 PIN to 9 PIN female extension cable,
and a 9 PIN to terminal cable, the connection as figure below.
Only four terminals are used for RS232 communication: SGND, RXD,
TXD, and GND. Plug the DB 25 PIN side into the printer port, the other side
connect with the other cable 9 PIN side, the left terminal side plug into the
device terminals, the connection and the terminal definition as figure below.
Device Terminals
Terminal
PC 9 PIN
Port Number Definitions
TXD--------------------------------------------------2
RXD
10
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
RXD--------------------------------------------------3
TXD
SGND-----------------------------------------------5
GND
GND-------------------------------------------------Shield Terminal
 Note: You can not use RS232 communication and connect the printer at
the same time.
3.5 Power Connection
This device is powered by 12VDC: You can use the 12V power supply
adapter which is provided along with the device. And then the device is power
on and get ready to work.
Connection: Plug the 12V power supply into the power port at the back of
the device. The power port position please refers to 2.1 Device Interface.
11
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
4. Test and Examine after Installation
1. After all system installation finished, make a test and examine prior to
power on.
2. Power on the device. The green LED begins to glitter after power up.
3. Enter menu  Option  Auto test, select [Test all] function.
4. Enter menu  User management  Enroll User  Enroll Card,Enroll
a user card, and test the device by swipe the card.
5. If there is no any problem, please delete this enrolled user and the
user card.
12
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
5. Other Functions
Side View:
Reset Button
USB Port
Figure 5-1
5.1 USB Port
You can use the U disk to download or upload the user information and
the verification records. The USB port please refers to the figure 5-1.
5.2 Reset Function
If the device does not work properly because of misuse or other
abnormality, you can use the “Reset” function to restart it. The reset button
please refers to the figure 5-1.
Operation: Remove the black rubber cap, and then stick the Reset
button hole with a sharp tool (the tip diameter less than 2mm).
13
US10 Series Installation Guide
5.3 Card Reader
Figure 5-2

Note: The barcode card reader is used for US10B device, and the
magnetic stripe card reader is used for US10M device.
5.3.1 Barcode Card Reader
The US10B device contain a barcode card reader module, slide the barcode
card through the card slot quickly, and the barcode side facing out, when you
hear the voice prompt, the card brush succeed. The card brush method is as
the figure 5-2.
When the card reader light is red, then the card brush is available.
5.3.2 Magnetic Stripe Card reader
The US10M device contain a magnetic stripe card reader module, slide the
magnetic stripe card through the card slot quickly, and the magnetic stripe
side facing out, when you hear the voice prompt, the card brush succeed.
The card brush method is as the figure 5-2.
14
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
5.4 WiFi Connection ★

Note: Only the device with WiFi module can communicate in the LAN
using WiFi function. If you need to use, please contact our business
representative or technical support.
The device can connect to the LAN through the embedded WiFi module,
upload and download the user information and verification data. The
following figure is an example of WiFi application.
About the operation and settings about the WiFi function please see related
user manual.
15
Error! Use the Home tab to apply 标题 1 to the text that you want to
appear here.
6. Trouble Shooting
Trouble
Cause & Measure
Power LED is off
Cause:
No power or lack of voltage.
Measure :
Check and examine the connection of power supply.
Measure the supply voltage, ensure that it is 12VDC.
Device is unable to
Cause:
connect with PC
The connection problem.
Measure:
Check and examine the connection of RS232 or
TCP/IP, whether its connection is correct or not.
When the device is
Cause :
power, it can not
Chip-on-board is broken.
enter the main menu
Measure:
Need to contact supplier and ask for repair.
The time display as
Cause:
“00:00”
The clock battery is broke down.
after
restarting
Measure:
Contact the reseller to replace a battery.
keystroke
sound
without
Cause:
①Trouble in the buzzer, loud- speaker or circuit.
②Set the parameter button beep to “N” in the device
Measure:
①Need to replace the buzzer and loudspeaker.
②Enter the Menu - Options-System Opt - Adv Option Button Beep, turn the parameter to “Y”
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement