User`s Manual

User`s Manual
RICOH PJ X4340 / RICOH PJ RX300
User’s Manual
1. Usage Notice
2. Introduction
3. Installation
4. Basic Operations
5. User Controls
6. Appendices
Read this manual carefully before you use this machine and keep it
handy for future reference. For safe and correct use, be sure to read
the Precautions in this manual before using the machine.
Table of Contents
Table of Contents.............................1
Usage Notice....................................2
Precautions..........................................2
Installing the Projector on a Wall or
Ceiling..................................................5
Safety Labels of This Machine.............7
Regulation & Safety Notices................8
Remote Control Battery.....................12
Warning.............................................. 12
Notes.................................................. 12
Other Information...............................14
Product Features...............................15
Introduction.....................................16
Package Overview.............................16
Product Overview..............................17
About Your Projector..........................18
Installation......................................22
Appendices.....................................43
Lamp Replacement Procedure..........43
Reset the lamp usage time................. 43
Compatibility Modes..........................44
Computer/Video/HDMI/Mac
Compatibility....................................... 44
Troubleshooting.................................46
Maintaining the filter...........................50
Configurations of Terminals...............51
Terminal: Computer in 1/2
[Monitor Out] (Mini D-sub 15 pin)........ 51
Terminal: PC Control (D-sub 9 pin :
female)................................................ 51
Specifications.....................................52
List of general specifications............... 52
Cabinet Dimensions...........................53
Trademarks........................................54
Connections.......................................22
Basic Operations............................24
Powering the projector On / Off.........24
Powering On the Projector.................. 24
Powering off the projector.................. 25
Warning Indicator................................ 25
Setting up...........................................26
Adjusting the Projector’s Focus.......... 27
Adjusting Projection Image Size......... 27
User Controls.................................29
On-screen Display Menus.................29
Picture................................................32
Position..............................................34
Setting................................................36
Audio..................................................38
Options..............................................39
3D......................................................42
1
English
Usage Notice
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s guide to
maximize the life of your unit.
▀■ Warning- This apparatus must be earthed.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Do not open or disassemble the projector as this may
cause electric shock.
▀■ Warning- When replacing the lamp, allow unit to cool down at
least 60 minutes, and follow all replacement instructions.
▀■ Warning- When the lamp reaches the end of its life, it will burn
out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp,
follow the procedures listed under “Replacing the
Lamp”.
▀■ Warning- Do not remove the cabinet cover, or you may be
exposed to dangerous voltage. Refer servicing to
qualified service personnel only.
▀■ Warning- This product should be operated only from the type
of power source which does not exceed the voltage
range specified on the rating label and the power
cord. If you are not sure of the type of power supply
to your home, consult your sales representative or
local power company.
▀■ Warning- Do not use the polarized plug with an extension cord
, receptacle, or other outlet unless the blades can be
inserted completely with three wire grounding type
to prevent blade exposure. Failure to follow these
instructions may result in fire or electric shock.
▀■ Warning- Plastic bags can be dangerous, please do not leave
near babies and young children. To avoid the threat
of suffocation, please keep away from their nose and
mouth.
English
2
Usage Notice
▀■ Caution- Never operate this unit on AC power during a thun-
derstorm. If you see lightning or hear thunder, never
touch the unit, cables and/or peripherals. An electric
surge caused by the storm, may result in an electrical
shock or damage to the unit.
▀■ Caution- Never push objects of any kind into this product
through openings as they may touch dangerous voltage points or short-out parts that could result in a fire
or electric shock. Never spill liquid of any kind on the
product.
▀■ Caution- Do not place or keep the projector within the reach of
the children. It may fall or tip over, possibly causing
serious injury.
▀■ Caution- Do not stack other equipment on this product and
do not place this product on other equipment. The
top and bottom surface of this product increase in
temperature during normal use and may damage the
other unit.
▀■ Caution- Do not use attachments not recommended by
RICOH. Use of an incompatible attachments could
cause hazards or damage to the product.
▀■ Caution- Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product.
▀■ Caution- Unplug this product from the wall outlet and take the
product to qualified service personnel if you encounter any of the following conditions:
a)The power supply cord or plug is damaged.
b)Liquid has been spilled, or objects have fallen into
the product.
c) The product has been exposed to rain or water.
d)The product does not operate normally when
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions.
e)The product has been dropped or damaged in any
way. (If the cabinet should break, please handle
with care to avoid injury.)
3
English
Usage Notice
▀■ Caution- This product incorporates glass components, includ-
ing a lens and a lamp. If these should break, please
handle with care to avoid injury and contact your sales
representative for repair service. Avoid any broken
pieces of glass since they may cause injury. In the
unlikely event that the lamp ruptures, thoroughly clean
the area around the projector and discard any edible
items placed in that area since they may be contaminated.
▀■ Caution- Do not place anything in front of the lens while the projector is operating. Things placed in front of the lens
may overheat and burn or start a fire.
▀■ Caution- Do not use lens cap when projector is powered on.
▀■ Caution- Unauthorized substitutions may result in fire, electric
shock, or other hazards. (Only the replacement of the
lamp should be made by users.)
▀■ Caution- Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to verify that the product is in proper operating
condition.
▀■ Caution- Do not leave thermal paper documents or easily de-
formed items on top of the unit or near the air exhaust
for long periods of time.
▀■ Caution- The heat from the unit could erase the information on
the thermal paper, or cause deformation or warping.
▀■ Caution- This projector will detect the life of the lamp itself. Be
sure to change the lamp when it shows warning messages.
▀■ Caution- Do not use the product in a closed installation loca-
tion. Do not place the product in a box or in any other
closed installation location. Otherwise it may overheat,
which could result in a risk of fire.
English
4
Usage Notice
Installing the Projector on a Wall or
Ceiling
yy Do not attempt to clean or replace parts for a machine that is installed in a
high location on a wall or ceiling. Doing so may cause it to fall down, resulting in an injury.
yy Do not open the lamp cover of a machine that is installed on a wall or ceiling. Doing so may cause the lamp cover to fall down. If the lamp is broken,
pieces of glass may fall and cause an injury.
yy Contact your sales or service representative to clean or replace parts for a
machine that is installed on a wall or ceiling.
yy If a machine is incorrectly installed on a wall or ceiling, it may fall down and
cause an injury. Contact your sales or service representative if you want to
install a machine on a wall or ceiling.
Safety Precautions to Be Followed
yy Do not obstruct the machine’s vents. Doing so risks fire caused by overheated internal components.
For users
yy Do not install the projector by yourself. Contact your sales or service representative if you want to install the projector on a wall or ceiling.
For sales or service representatives
yy Use brackets that are strong enough to support the projector. The
projector weighs about 2.9 kg (6.4 lb.).
yy The projector must be installed in a location that is sturdy enough
to support the full weight of the projector and brackets.
yy Use only the screws (three M3×16 screws) to attach the brackets to
the projector.
yy Use all three of the projector’s screw holes to attach the brackets.
The locations of the screw holes are shown in the illustration below.
Make sure that the screws are tightened firmly.
5
English
Usage Notice
Do:
 After unpacking this product, read the manual carefully, and
follow all the operating and other instructions.
 Turn off the product before cleaning.
 Use a soft cloth moistened with mild detergent to clean the
 Disconnect the power plug from AC outlet if the product is
display housing.
not being used for a long period of time.
Do not:
 Block the slots and openings on the unit provided for ventila-
tion.
 Use abrasive cleaners, waxes or solvents to clean the unit.
 Use under the following conditions:
-
-
-
-
Extremely heat, cold or humidity.
In areas susceptible to excessive dust and dirt.
Near any appliance generating a strong magnetic field.
In direct sunlight.
Important:
Contents of this manual are subject to change without prior notice.
In no event will the company be liable for direct, indirect, special,
incidental, or consequential damages as a result of handing or
operating this product.
English
6
Usage Notice
Safety Labels of This Machine
1 Do not block the air intake or exhaust. Doing so could
cause a fire due to internal overheating. Do not place your
hands, face, or other objects near the air exhaust, the lamp
cover or the bottom of the unit. Doing so could result in
injury and/or damage the object.
2 Do not look into the lens while the lamp is on. The strong
light from the lamp may cause damage to your eyesight.
3 Do not place anything in front of the lens while the projector
is operating. Things placed in front of the lens may overheat and burn or start a fire. If you want to temporarily stop
the projected image, use the AV mute on the remote control
or the keypad.
4 To replace the lamp, first unplug the power cord then wait
for more than 1 hour. The lamp might be broken. Be careful
of pieces of broken glass.
5 Do not remove any screws except the lamp cover screws.
Do not block or cover the vents.
4
1
3 2
5
7
English
Usage Notice
Regulation & Safety Notices
This appendix lists the general notices of your Projector.
Notice: Users in the United States of America
FCC notice
MODEL NAME: RICOH PJ X4340
TRADE NAME: PROJECTOR
MODEL NAME: RICOH PJ X4340
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for
a Class B digital device pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference
to radio or television reception, which can be determined by turning
the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
▀■ Reorient or relocate the receiving antenna.
▀■ Increase the separation between the device and receiver.
▀■ Connect the device into an outlet on a circuit different from that to
which the receiver is connected.
▀■ Consult the dealer or an experienced radio/television technician
for help.
English
8
Usage Notice
RESPONSIBLE PARTY: Ricoh Americas Corporation
5 Dedrick Place, West Caldwell, NJ 07006
Phone: 973-882-2000
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by
the manufacturer could void the user’s authority, which
is granted by the Federal Communications Commission,
to operate this projector.
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND
MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
Notes to Users in the State of California
Perchlorate Material - special handling may apply, See www.dtsc.
ca.gov/hazardouswaste/perchlorate.
WARNING: Handling the cord on this product will expose you to lead,
a chemical known to the State of California to cause cancer, and birth
defects or other reproductive harm. Wash hands after handling.
9
English
Usage Notice
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canada.
Declaration of Conformity for EU
countries
▀■ EMC Directive 2004/108/EC (including amendments)
▀■ Low Voltage Directive 2006/95/EC
Notice: Users in EU countries
CE Marking Traceability Information (For
EU Countries Only)
Manufacturer:
Ricoh Co., Ltd.
3-6 Nakamagome 1-chome, Ohta-ku, Tokyo. 143-8555,
Japan
Authorized representative:
Ricoh Europe PLC
20 Triton Street, London. NW1 3BF, United Kingdom
English
10
Usage Notice
User Information on Electrical and
Electronic Equipment
Users in the countries where this symbol shown in this section
has been specified in national law on collection and treatment
of E-waste.
Our Products contain high quality components and are designed to facilitate
recycling.
Our products or product packaging are marked with the symbol below.
This product contains substances which are harmful to humans and the environment.
• The lamp contains mercury.
Please dispose of this product or used lamps in accordance
with local regulations.
The symbol indicates that the product must not be treated as
municipal waste. It must be disposed of separately via the appropriate return and collection systems available. By following
these instructions you ensure that this product is treated correctly and help to reduce potential impacts on the environment
and human health, which could otherwise result from inappropriate handling. Recycling of products helps to conserve
natural resources and protect the environment.
For more detailed information on collection and recycling systems for this product, please contact the shop where you purchased it, your local dealer or sales/service representatives.
Notice: Users in Turkey
11
English
Usage Notice
Remote Control Battery
If you wish to discard this product, please contact your local
authorities, the shop where you bought this product, your local
dealer or sales/service representatives.
Warning
• Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or
leak and may result in serious injury. If battery-leaking fluid
contacts skin, wash the fluid off immediately with clean water
and consult a doctor. If the fluid spills on an instrument, avoid
contact and wipe it off using tissue paper. Then dispose of the
used tissue paper as flammable garbage after moistening the
tissue with water.
• Do not ingest battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin
cell battery.
If the coin cell battery is swallowed, it can cause severe inter­
nal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using
the product and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention.
Notes
• Be sure to use CR2025 lithium 3.0 V coin battery.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of
battery disposal.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace the battery.
• Avoid contact with water or liquid.
• Do not expose the remote control to moisture or heat.
• Do not drop the remote control.
• If the battery has leaked in the remote control, carefully wipe
the case clean and install new battery.
• Dispose of used battery according to the instructions.
English
12
Usage Notice
Notice: Users in the EU
Note for the Battery and/or Accumulator
Symbol
In accordance with the Battery Directive 2006/66/EC Article 20
Information for end-users Annex II, the above symbol is printed
on batteries and accumulators. This symbol means that in the
European Union, used batteries and accumulators should be
disposed of separately from your household waste. In the EU,
there are separate collection systems for not only used electrical and electronic products but also batteries and accumulators. Please dispose of them correctly at your local community
waste collection/recycling centre.
Notice: Users in Taiwan
適用於台灣。
13
English
Usage Notice
Other Information
Copyrights to Images
When projecting images using the projector, be careful
not to infringe the copyright of protected materials.
The following are examples that may infringe the copyright
of protected materials.
• Broadcasting images or movies for commercial purposes
• Modifying images or movies using functions such as freeze,
magnify, or zoom to broadcast images for commercial purposes or public viewing
• Varying the aspect ratio of images or movies using a function
that changes the screen size to broadcast images for commercial purposes or public viewing
Note to Users Viewing 3D Images
Pay attention to the following points when viewing images using 3D glasses with projector:
• How 3D images are viewed may vary according to the individual.
• Do not use 3D glasses for viewing any material other than
3D images.
• Before viewing 3D images, make sure to read the manuals
provided with your 3D glasses and 3D compatible content.
• Avoid viewing 3D images for a long period of time. Take a
break of 15 minutes or longer after every hour of viewing.
• If you feel sick while viewing 3D images, stop viewing them.
If you continue to feel sick, consult a doctor.
• When viewing 3D image in a room where on LED lighting
system or fluorescent lights are used, you may feel that the
light in the room flickers. If this is the case, dim the lights
until you do not notice any flickers, or turn off the lights.
• If you or any member of your family has a history of lightsensitive seizures, consult a doctor before viewing 3D images.
English
14
Usage Notice
Product Features
▀■ XGA (1024x768) Native resolution
▀■ HD compatible – 720p and 1080p supported
▀■ VGA monitor loop through(works in standby mode >
0.5W)
▀■ BrilliantColorTM Technology
▀■ Security Bar and antitheft lock hole
▀■ RS232 control
▀■ Rapid shutdown
▀■ Built-in mono 8 Watt speaker
▀■ Eco+ and Quick Resume
15
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Projector with lens cap
Remote Control
(CR2025 Battery is
contained. )
Documentation :
Read This First

English
16
Power Cord
CD-ROM
VGA Cable
Introduction
Product Overview
2
12
9
1
12
8
2
12
3
8
12
4
7
15
12
12
5
12
6
10
12
14
12
13
12
12
1. Control panel and
indicator light
2. Air inlet
3. Speaker
4. Security bar
5. Focus ring
11
12
Adjust the projector’s focus
6. Projection lens
7. Remote signal receiver
8. Exhaust port
9. Lamp cover
10. Safety lock
This lock catch is used to install
an anti-theft lock to prevent video
machines from being stolen.
11. Air filter (right)
12. Adjustable feet
Adjust the projection angle
13. Power cord socket
14. Air filter (left)
15. Terminal connection port
17
English
Introduction
About Your Projector
Control Panel and Indicators
7
1
6
2
5
3
4
(1) <Power> indicator
Indicates the projector’s status.
(2) < > button
Turns the projector on/off.
(3) ▲▼◄► buttons
Uses to operate menu.
(4) <Input/Enter> button
Displays [Source] menu when menu is not
displayed. (Confirm your section of items
when menu is displayed. )
(5) <Menu> button
Turns the main menu on/off.
English
18
(6) <Temp> indicator
Indicates the status of the internal temperature or the cooling fan of the projector.
(7) <Lamp> indicator
Indicates the projector’s lamp status.
Introduction
Connecting terminals
RICOH PJ X4340
10
1
2
7
RICOH PJ RX300
10
2
7
(1) <HDMI In>
This is a terminal to connect to HDMI signal.
(2) <Monitor Out>
This is a terminal to output the RGB signal
or component signal via <Computer 1 In> or
<Computer 2 In> terminal.
(3) <Computer 1 In>
This is a terminal to input the RGB signal or
component signal.
(4) <Video In>
This is a terminal to input the video signal.
(5) <Audio 2 In>
This is a terminal to input the audio signal
from the video equipment connected to the
<Video In> terminal.
(6) <Audio 1 In>
This is a terminal to input the audio signal
from the computer connected to the <Computer 1 In> or <Computer 2 In> terminal.
3
4
8
5
6
9
3
8
(7) <PC Control>
This is a RS-232C compatible terminal to
externally control the projector.
(8) <Computer 2 In>
This is a terminal to input the RGB signal or
component signal.
(9) <Audio out>
This is a terminal to output the audio signal
input to the projector. The output level can
be adjusted.
(10)Service terminal
Note
yy When the <HDMI IN> terminal is connected to
a computer via a HDMI-DVI conversion cable,
it can only input video signal and the analog
audio signal can not be input.
19
English
Introduction
Remote control
6
1
7
2
8
9
3
10
11
4
12
5
13
(1) <Power> button
Turns the projector on/off
(2) <Aspect> button
Select aspect ratio among Auto, 4:3,16:9, 16:10
(3) <Menu> button
Turns the main menu on/off or returns to upper
level in the menu operations.
(4) <Freeze> button
The screen will be freezed.
(5) <ECO> button
Displays Lamp Power mode menu.
(6) <Picture> button
Selects the color mode among Dynamic, PC,
Movie, Game and User.
(7) <Input> button
Displays source select menu.
(8) <AV Mute> button
Mutes audio and video.
(9) ▲▼◄► buttons
Uses to operate menu.
Keystone can be adjusted by pressing ▲ and
▼buttons when menu is not displayed.
(10) <Auto Set> button
Automatically synchronize the projector to the input
source.
English
20
(11) <Enter> button
Confirm your section of items in menu system.
(12) <Volume +/-> buttons
Adjust sound level.
(13) <Magnify +/-> buttons
Adjusts magnification ratio of the displayed image.
Attention
yy Do not drop the remote control.
yy Avoid contact with liquids.
yy Do not attempt to modify or disassemble the remote control.
Note
yy The <Auto Set> operation may not optimize the image position or the resolution, depending on the input signal format or
the image contents. In this case, switch to a different image
and execute <Auto Set> again.
Introduction
Changing the battery of the remote control
25
20
LT
R
M
S
Remove the old battery
and install new one
(CR2025). Ensure that
the side with a “+” is
facing up.
C
TS
3V
3. Put the cover
back.
3V
O
2. Install new battery into the
compartment.
C
R
20
25
O
L
1. Press firmly and slide
the battery cover off.
To ensure safe operation, please observe the
following precautions :
■ Never throw batteries into a fire.
■ Do not ingest battery, Chemical Burn Hazard.
■ Keep new and used batteries away from children.
For more detailed information, please see p.9.
Remote Control Operating
yy When pointing the remote control directly toward the projector (Remote control signal receiver), operating range for the remote
control is within 8 m (26.25 ft). Also, operation range available for four directions (up, down, left, right to the projector) is ± 30° and the
operation distance may become short.
yy If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate
correctly.
yy You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to the loss of
light caused by the properties of the screen.
yy When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become inoperative. Set the projector as far from the luminous source as possible.
yy You can operate all of the functions of the projector via the remote control. Make sure not to lose the remote control.
yy Before using the remote control for the first time, remove the transparent insulation sheet.
Transparent insulation sheet
8m(26.25ft)
±30°(horizontal)
±30°(Vertical)
21
English
Installation
Connections
Connecting example: Computers
RICOH PJ X4340
Control
Computer
Computer
Monitor
Computer
MONITOR OUT (COMP.)
HDMI IN
PC CONTROL
RICOH PJ RX300
Control
Computer
Monitor
MONITOR OUT (COMP.)
PC CONTROL
English
22
Computer
Audio equipment
Installation
Connecting example: AV equipment
RICOH PJ X4340
Blu-ray disk
player
DVD player
VCR
Audio equipment
MONITOR OUT (COMP.)
HDMI IN
PC CONTROL
23
English
Basic Operations
Powering the projector On / Off
Powering On the Projector

When VGA Out
(Standby) is set
to Off, the Monitor
Out output will be
deactivated when
the projector is in
standby.
1. Remove the lens cap if it is on the lens.
2. Securely connect the power cord and signal cable. When the
power cord is connected, the Power indicator will turn Amber.
3. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The Power indicator will now
turn Green.
The startup screen will display in approximately 10 seconds.
The first time you use the projector, you will be asked to
select the preferred language and power saving mode.
4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Auto Source” has been set to “On”. See
p.35 (User Controls/Auto source explanation page)
If you connect multiple sources at the same time, press the
“Input/Enter” button on the control panel or “Input” button on
the remote control to switch between inputs.
Turn on the
projector first and
then select the
signal sources.
English
24
Basic Operations
Powering off the projector
1. Press the “ ” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to confirm otherwise the
message will disappear after 10 seconds. When you press
the “ ” button for the second time, the fan will start cooling the system and will shut down.
2. The cooling fans continue to operate for about 60 seconds
for cooling cycle and the Power indicator will Flash Amber.
When the Power indicator lights solid Amber, the projector
has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
Contact your
sales representative for repair
service if the
projector displays
these symptoms.
 “Lamp” LED indicator is lit red and “Power” indicator
flashes amber.
 “Temp” LED indicator is lit red and “Power” indicator flashes amber. This indicates the projector has overheated.
Under normal conditions, the projector can be switched
back on.
 “Temp” LED indicator flashes red and “Power” indicator
flashes amber.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up again,
please contact your dealer for assistance.
25
English
Basic Operations
Setting up
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting the image height.
Extend the adjustable feet by rotating in the direction shown in the below picture and retract by rotating
in the opposite direction.
Adjustable range
Rear adjustable foot : 10
mm (0.4”)
The rear adjustable foot stretch to its end
Adjustable range
Front adjustable foot :
19 mm (0.75”)
The front adjustable foot stretch to its end
6°
2.7 °
Attention
yy It is very hot around the lamp and the air exhaust port when the lamp is lighting and for a while after
the lamp is turned off. And, hot air is expelled from the air exhaust port when the lamp is lighting. Do
not touch there directly when adjusting the adjustable feet.
yy Do not stretch the adjustable feet more than the above mentioned length. Otherwise, the projector
may be unstable or the adjustable feet may fall off.
English
26
Basic Operations
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 0.51 to 2.54
meters (1.67 to 8.34 feet ).
Focus Ring
Adjusting Projection Image Size
Projection Image Size from 40” to “200” (1.02 to 5.08 meters).
Top View
Screen
Screen (W)
Height
Projection Distance (D)
Screen
Side View
Screen (H)
Dia
go
na
l
Width
Offset (Hd)
Projection Distance (D)
27
English
Basic Operations
XGA
Diagonal length
(inch) size of
4:3 Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(feet)
Offset (Hd)
Width
Height
Width
Height
(m)
(inch)
40.00
0.81
0.61
32.00
24.00
0.50
1.64
0.09
3.60
60.00
1.22
0.91
48.00
36.00
0.75
2.46
0.14
5.40
70.00
1.42
1.07
56.00
42.00
0.88
2.89
0.16
6.30
80.00
1.63
1.22
64.00
48.00
1.00
3.28
0.18
7.20
90.00
1.83
1.37
72.00
54.00
1.13
3.71
0.21
8.10
100.00
2.03
1.52
80.00
60.00
1.25
4.10
0.23
9.00
120.00
2.44
1.83
96.00
72.00
1.50
4.92
0.27
10.80
150.00
3.05
2.29
120.00
90.00
1.88
6.17
0.34
13.50
180.00
3.66
2.74
144.00
108.00
2.26
7.41
0.41
16.20
200.00
4.06
3.04
160.00
120.00
2.51
8.23
0.46
18.00
This table is for user’s reference only.
English
(m)
28
User Controls
On-screen Display Menus
How to operate menu
■ Operation steps
1) Press <Menu> button on the remote control or on the control panel.
yy Main Menu displays.
2) Use ▲▼ to select any item in the Main Menu.
yy The selected item is highlighted in orange.
3) Press ►, <Input/Enter> or <Enter>.
yy Items in the Sub Menu can be selected.
4) Use ▲▼ to select any item in the Sub Menu.
yy The selected item is highlighted in yellow.
5) Press ►, <Input/Enter> or <Enter> to display adjusting box.
6) Use ▲▼ to switch or adjust desired item by pressing ◄► keys.
7) Press <Menu> button to go back to the Sub Menu and press again to go back to the Main
Menu, press <Menu> button once more to close the Main Menu.
Sub Menu
Main Menu
Setting Value
or
Adjusting Value
Note
yy Some items may not be adjusted or used for certain signal formats input to the projector. The MENU items that
cannot be adjusted or used are shown in gray characters, and they cannot be selected.
yy Some items can be adjusted even if signals are not input.
yy See pages 30 and 31 for details on the items of Sub Menu.
29
English
User Controls
Menu Tree
Main Menu
Picture
Sub Menu
2nd Sub Menu
Color Mode
Dynamic / PC / Movie / Game / User
Wall color
White / Light Yellow / Light Blue / Pink /
Dark Green
Default Value
White
Brightness
0 ~ 100
Contrast
0 ~ 100
Sharpness
0 ~ 31
Saturation
0 ~ 100
Hue
0 ~ 100
Gamma
Position
Setting
Audio
English
Range
0 ~ +3
Color Temp.
Low / Mid / High
Color Space
Auto / RGB / YUV
Auto
Aspect Ratio
Auto / 4:3 / 16:9 / 16:10
Auto
Phase
0 ~ 31
Clock
-5 ~ 5
H. Position
V. Position
Digital Zoom
0
0 ~ 10
V Keystone
0
-40 ~ 40
Ceiling Mount
Front / Front Ceiling / Rear / Rear Ceiling
Language
English / German / Spanish / French / Italian English
/ Dutch / Portuguese / Simplified Chinese /
Polish / Korean / Russian / Swedish / Traditional Chinese/Arabic / Norwegian / Turkish /
Thai / Czech / Hungarian / Kazakh
Menu Location
Left Top / Right Top / Center / Left Bottom /
Right Bottom
Center
Closed Caption
Off / CC1 / CC2 / CC3 / CC4
Off
VGA Out (Standby)
On / Off
Off
Test Pattern
On / Off
Off
Startup Logo
On / Off
On
Reset
Yes / No
No
Mute
On / Off
Off
Volume
In Standby Mode
(Audio)
30
Front
20
On / Off
Off
0 ~ 32
User Controls
Main Menu
Sub Menu
2nd Sub Menu
Default Value
Auto Source
On / Off
On
Input
HDMI, Computer 1, Computer 2,
Video
Auto Power Off (Min)
0
Range
0~120
Lamp Hours Used (Normal)
Lamp Hours Used (ECO)
Lamp Settings
Options
Lamp Life
Reminder
Off/On
On
Lamp
Power
Mode
Normal / Auto / ECO1
/ ECO2
Normal
Clear
Lamp
Hours
Yes / No
High Altitude
On / Off
Dust Filter Reminder
Filters Remind (Hour)
Cleaning
up
reminder
Information
Off
0
0 ~ 1000
Yes / No
Source
Resolution
Software Version
Color Space
Aspect Ration
3D
3D
On / Off
3D Invert
On / Off
3D Format
Side-by-Side / Top and Bottom /
Frame Sequential
Off
31
English
User Controls
Picture
Select [Picture] from the Main Menu (see “How to
operate menu” on page 29) and then select the
item from the Sub Menu.
Wall color
Select an appropriate color for wall projection.
1) Press ▲▼ to select [Wall color].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
White
For White color.
Light Yellow
For Light Yellow color.
Light Blue
For Light Blue color.
Pink
For Pink color.
Dark Green
For Dark Green color.
Brightness
Adjust the brightness of the projected image.
Color Mode
There are factory presets optimized for various types of
images.
1) Press ▲▼ to select [Color Mode].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
Dynamic
For bright room.
PC
For computer or notebook.
Movie
For home theater.
Game
For amusing games.
User
Color mode user adjusted.
Note
yy When [Brightness], [Contrast], [Sharpness], [Saturation], [Hue], [Gamma] or [Color Temp] is adjusted,
[Color Mode] will change to [User].
yy The adjusted value of [User] depends on the type of
the input signal.
Video, 480i/576i, 480p/576p, 720p, 1080i, 1080p,
RGB, HDMI (YUV), HDMI (RGB).
yy <Picture> button on the remote also can be used for
this function.
English
32
1) Press ▲▼ to select [Brightness].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
Increases the brightness of the screen.
Maximum
value 100
Press ◄.
Reduces the brightness of the screen.
Minimum
value 0
Contrast
Adjust the contrast.
1) Press ▲▼ to select [Contrast].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
Increase the contrast
of the screen.
Maximumvalue 100
Press ◄.
Decrease the contrast Minimum
of the screen.
value 0
User Controls
Sharpness
Note
Adjust the sharpness of the projected image.
1) Press ▲▼ to select [Sharpness].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
Contours become
sharper.
Maximumvalue 31
Press ◄.
Contours become
softer.
Minimum
value 0
Note
yy [Sharpness] can be adjusted only when Video is
selected.
Saturation
Adjust a video image from black and white to saturated
color.
1) Press ▲▼ to select [Saturation].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
Increase the intensity
of the color.
Maximumvalue 100
Press ◄.
Decrease the intensity Minimum
of the color.
value 0
Note
yy [Saturation] can be adjusted only when Video is
selected.
Hue
Adjust the skin tone.
1) Press ▲▼ to select [Hue].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
Adjust the color to be
greenish.
Maximumvalue 100
Press ◄.
Adjust the color to be
reddish.
Minimum
value 0
yy [Hue] can be adjusted only when video is selected
and the color mode is NTSC or NTSC 4.43.
Gamma
Adjust the gamma table when the dark areas or bright
areas of the image is not clear.
1) Press ▲▼ to select [Gamma].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the setting value.
Operation
Adjustment
range
Adjustment
Press ►.
Emphasize detail in
dark areas of image.
Maximumvalue +3
Press ◄.
Emphasize detail in
bright areas of image.
Minimum
value 0
Color Temp
Select the color temperature.
1) Press ▲▼ to select [Color Temp].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
Low
The screen looks warmer.
Mid
The medium color temperature.
High
The screen looks colder.
Color Space
Select an appropriate color matrix type from Auto, RGB
or YUV.
1) Press ▲▼ to select [Color Space].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
Auto
Switched automatically according
tothe input signal.
RGB
For computer input.
YUV
For component input.
Note
yy [Color Space] will be in gray and can not be operated
when Video is selected.
33
English
User Controls
Position
Select [Position] from the Main Menu (see “How
to operate menu” on page 29) and then select the
item from the Sub Menu.
tels to display programs for a commercial purpose or
for public presentation, note that adjusting the aspect
ratio or using the zoom function to change the screen
pictures may be an infringement of the rights of the
original copyright owner for that program under copyright protection laws. Take care when using a function
of the projector such as the aspect ratio adjustment,
zoom function, etc.
yy If conventional (normal) 4:3 pictures which are not
wide-screen pictures are displayed on a wide screen,
the edges of the pictures may not be visible or they
may become distorted. Such pictures should be
viewed as with an aspect ratio of 4:3 in the original
format intended by the creator of the pictures.
Phase
Adjust to achieve an optimal image when there is a
flickering image.
Aspect Ratio
Use this function to choose your desired aspect ratio.
1) Press ▲▼ to select [Aspect Ratio].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
1) Press ▲▼ to select [Phase].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
Note
yy [Phase] can be adjusted only when Computer is
selected.
Clock
Adjust to achieve an optimal image when there is a vertical flicker in the image.
Auto
The projector displays the image by
automaticallyswitching the screen
sizes between 4:3 and 16:9.
4:3
Input signal is displayed to full
screen. This mode is for 4:3 aspect
images.
1) Press ▲▼ to select [Clock].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
16:9
Input signal is displayed with 16:9
aspect in the center of the screen.
This mode is for 16:9 aspect
signals.
yy [Clock] can be adjusted only when Computer is
selected.
16:10
This format is for 16:10 input
sources, like wide screen laptop.
<Aspect> button on the remote also can be used for this
function.
Note
yy If an aspect ratio which is different from the aspect
ratio for the input signals is selected, the pictures will
appear differently from the originals. Be careful of this
when selecting the aspect ratio.
yy If using this projector in places such as cafes or ho-
English
34
Note
H Position
Shift the projected image position horizontally.
1) Press ▲▼ to select [H Position].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
Note
yy [H Position] can be adjusted only when Computer is
selected.
User Controls
V Position
Shift the projected image position vertically.
1) Press ▲▼ to select [V Position].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
Note
yy [V Position] can be adjusted only when Computer is
selected.
Digital Zoom
Adjust the magnification of the image. Magnification can
be set from 1.0x to 2.0x in 0.1 increments.
1) Press ▲▼ to select [Digital Zoom].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
Note
yy When the [Digital Zoom] is in the enlarge status, exits
the menu screen and the [Zoom] picture will display
at the bottom left of the screen. This indicates the
zoom function is in use.
yy Under the enlarge status, press ▲▼◄► to move the
enlarged image.
yy If the input signal is changed under the enlarge status, the magnification of [Digital Zoom] will be reset.
yy [Magnify +/-] buttons also can be used to adjust this.
V Keystone
This function is used to adjust keystone distortion of the
projected image.
1) Press ▲▼ to select [V Keystone].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the level.
yy ▲▼ buttons on the remote also can be used to
adjust this when MENU is not displayed.
Operation
Screen image
Press the ▲► on
the remote control
or the ► on the
control panel to
adjust the upper of
the keystone.
Press the ▼◄ on
the remote control
or the ◄ on the
control panel to
adjust the bottom of
the keystone.
Note
yy The adjusted keystone distortion will store automatically even when the signal is interrupted or the AC
power cord is plugged out or turned off the projector.
yy When the larger amount of keystone correction, the
picture quality will degrade and it will get harder to
focus with more correction. Set the projector so the
correction will be as small as possible.
yy When keystone correction is performed, the screen
size will also change.
yy Part of Closed caption may not be displayed when
high compensation values are set in [V Keystone].
Ceiling Mount
This function is used to project the image from a ceilingmounted projector.
1) Press ▲▼ to select [Ceiling Mount].
2) Press ►, <Input/Enter> or <Enter> to display
the choosing dialog box.
3) Press ◄► to select the desired item.
Front
When setting on a desk/floor and projected from front side of the screen.
Front
Ceiling
When mounting on the ceiling and projected from front side of the screen.
Rear
When setting on a desk/floor and projected from back side of the screen.
(Using translucent screen).
Rear
Ceiling
When mounting on the ceiling and projected from back side of the screen.
(Using translucentscreen).
35
English
User Controls
Setting
Select [Setting] from the Main Menu (see “How to
operate menu” on page 29) and then select the
item from the Sub Menu.
Off
Do not display Closed Caption.
CC1
Displays the CC1 data.
CC2
Displays the CC2 data.
CC3
Displays the CC3 data.
CC4
Displays the CC4 data.
Note
yy The closed caption is mainly used in the north America.This function shows the text information contained
in the image signal. Captions may not be displayed
with signals from some devices or software.
yy You can select [Closed Caption] only when NTSC
signal from video terminal.
yy When Menu screen is displayed, the caption will not
be displayed.
yy Part of Closed caption may not be displayed when
high compensation values are set in [V Keystone].
VGA Out (Standby)
Language
The language used in the On-Screen Menu is available
in English, German, Spanish, French, Italian, Dutch,
Portuguese, Simplified Chinese, Polish, Korean, Russian, Swedish, Traditional Chinese, Arabic, Norwegian,
Turkish, Thai, Czech, Hungarian and Kazakh.
1) Press ▲▼ to select [Language].
2) Press ►, <Input/Enter> or <Enter> to display
the language dialog box.
3) Press ▲▼ to select the desired item
and Press ►, <Input/Enter> or <Enter> to
choose.
Menu Location
Switch the menu location on the display screen.
yy Change order: Left Top  Right Top  Center 
Left Bottom  Right Bottom.
1) Press ▲▼ to select [Menu Location].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to select the desired item.
Closed Caption
1) Press ▲▼ to select [Closed Caption].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to select the desired item.
English
36
When in standby mode, choose whether to output the
signal from <Computer 1 In> to <Monitor Out> terminal.
1) Press ▲▼ to select [VGA Out (Standby)].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
On
Output image signal from <Monitor
Out> terminal when theprojector is
in standby mode.
Off
Image signal from <Monitor Out>
terminal can not be output when the
projector is in standby mode.
Test Pattern
Use this function to display built-in test pattern when
installing the projector.
1) Press ▲▼ to select [Test Pattern].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
yy If you want to return the normal mode to the
previous image, set [Test Pattern] to [Off] in the
[Setting] menu.
On
Display the built-in Test Pattern.
Off
Disable the function.
User Controls
Startup Logo
Set this function to display the RICOH logo when the
projector is turning on.
1) Press ▲▼ to select [Startup Logo].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
On
The logo will display when the
projector is turning on.
Off
The logo will not display when the
projector is turning on.
Reset
Return all data to the factory defaults.
1) Press ▲▼ to select [Reset].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ▲▼ to select [Yes].
4) Press ►, <Input/Enter> or <Enter> to execute.
Note
yy Lamp used time in the [Options] menu will not be
reset.
37
English
User Controls
Audio
Select [Audio] from the Main Menu (see “How to
operate menu” on page 29) and then select the
item from the Sub Menu.
In Standby Mode (Audio)
This function is used to switch the output audio signal
from the <Audio Out> terminal On/Off at standby mode.
1) Press ▲▼ to select [In Standby Mode
(Audio)].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to switch [On]/[Off].
On
Output the audio signal from the
<Audio Out> terminal when in
Standby mode.
Off
Mute the audio signal from the
<Audio Out> terminal when in
Standby mode.
Note
Note
yy “AUDIO” menu is not available on RICOH PJ RX300.
Mute
Temporarily turn off the sound.
1) Press ▲▼ to select [Mute].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
On
Mute.
Off
Output audio.
Volume
Adjust the volume.
1) Press ▲▼ to select [Volume].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust the volume.
Operation
Adjustment
Adjustment range
Press ►.
Turn up the
volume
Maximum value 32
Press ◄.
Turn down the
volume
Minimum value 0
yy You can also press the <Volume +/-> buttons on
the remote control.
English
38
yy When setting the [In Standby Mode (Audio)] function
to [On] and in Standby mode status, the connected
audio signal to <Audio 1 In> terminal can be output
from the <Audio Out> terminal. The audio signal
output level is fixed and cannot be adjusted.
User Controls
Options
Select [Options] from the Main Menu (see “How
to operate menu” on page 29) and then select the
item from the Sub Menu.
3) Press ▲▼ to select the input you want to
search and press ►.
yy The input with a check mark will be able to be
searched when [Auto Source] is set to [On].
yy To remove the check mark, choose the desired
item and press ►, <Input/Enter> or <Enter>.
Auto Power Off (Min)
Set the time to automatically turn off the projector when
there is no signal input.
1) Press ▲▼ to select [Auto Power Off (Min)].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to adjust off timer (min).
Auto Source
Set the automatic signal search function when power on
or the source of the signal being received is lost.
1) Press ▲▼ to select [Auto Source].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
On
Off
It will automatically search and
display the signal sources marked
in the [Options]-[Input] when power
on or the source of the signal being
received is lost.
When the source of the signal being
received is lost, it will not search
other sources.
yy Search and display order: [Computer 1] 
[Computer 2]  [HDMI]  [Video]  [Computer
1] .
Input
Set the automatic search signal source for [Auto
Source].
1) Press ▲▼ to select [Input].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
yy The [Input] menu dialog box is displayed.
yy When set to [0 (min)], this function is disable.
yy You can set the time in 5 minutes intervals and the
longest set time is 120 minutes.
Note
yy 60 seconds before the auto power off, the countdown screen will appear. The countdown screen will
disappear if there is signal input or operation to the
projector.
Lamp Settings
Displays and sets detail of the lamp settings.
1) Press ▲▼ to select [Lamp Settings].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
„„Lamp Hours Used (Normal)
yy Displays the used lamp hours under [Normal]
lamp power mode.
„„Lamp Hours Used (ECO)
yy Displays the used lamp hours (in real time) under
[Auto] / [ECO1]([ECO]) / [ECO2] lamp power
mode. The time is displayed as the sum of the
time under each setting of [Auto], [ECO1]([ECO])
and [ECO2] lamp power mode.
„„Lamp Life Reminder
1) Press ▲▼ to select [Lamp Life Reminder].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to switch [On]/[Off].
39
English
User Controls
On
Displays the lamp warning
message.
Off
The warning lamp message will not
be displayed.
Attention
yy If [Lamp Life Reminder] is set to [Off], the lamp warning message will not be displayed when the lamp
used time reaches the end of lamp life. In this case,
please check the lamp life with the values at the
[Lamp Hours Used (Normal)] and [Lamp Hours Used
(ECO)].
High Altitude
Set to [On] when the projector is used at elevation
between approx. 1 000 m (3 300 ft) and approx. 3 000
m (10 000 ft).
1) Press ▲▼ to select [High Altitude].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to switch [On]/[Off].
On
For the elevation between approx. 1
000 m (3 300 ft) and approx. 3 000
m (10 000 ft).
Off
For the elevation below approx. 1
000 m (3 300 ft).
„„Lamp Power Mode
yy Selects desired lamp power mode under different
situations.
1) Press ▲▼ to select [Lamp Power Mode].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ◄► to select the desired item.
Normal
Normal brightness.
Auto
The brightness level of the content
is automatically detected to
significantlyreduced lamp power
consumption during periods of
inactivity.
ECO1
Lower brightness reduces the lamp
power consumption and extends
the lamp life.
ECO2
Lowest brightness reduces the
lamp power consumption and
extends the lamp life.
Note
yy When there is no signal for more than 5 minutes, the
lamp power will be decreased automatically for power
saving.
„„Clear Lamp Hours
yy Reset the lamp usage time after replacing the
lamp unit.
1) Press ▲▼ to select [Clear Lamp Hours].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ▲▼ to switch [Yes]/[No].
4) Press ►, <Input/Enter> or <Enter> to execute.
Note
yy When [On] is selected, the speed and the noise of the
fan will increase. Do not use this projector in place
elevation is over 3000m (10000ft).
Dust Filter Reminder
Set the cleaning cycle of the filters and reset the use
time of the filters.
1) Press ▲▼ to select [Dust Filter Reminder].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
„„Filters Remind (Hour)
yy Set the interval timer to display the Dust Filter
Reminder message.
1) Press ▲▼ to select [Filters Remind].
2) Press ►, <Input/Enter> or <Enter> to display
the adjustment dialog box.
3) Press ◄► to set the time.
yy When set to 0 (Hour), this function is disabled.
yy The factory default is 0 hour.
yy You can set the time in between 50 hours and
1000 hours.
„„Cleaning up Reminder
yy Reset the air filter used time to zero.
yy Reset the air filter hour counter after cleaning or
replacing the dust filter.
1) Press ▲▼ to select [Cleaning up Reminder].
2) Press ►, <Input/Enter> or <Enter> to display
the setting dialog box.
3) Press ▲▼ to switch [Yes]/[No].
4) Press ►, <Input/Enter> or <Enter> to execute.
Note
English
40
User Controls
yy It is recommended to clean the air filters regularly
every 500 hours of usage.
Information
Displays the input signal source and setting state information of the projector.
1) Press ▲▼ to select [Information].
2) Press ►, <Input/Enter> or <Enter> to display
the information dialog box.
yy Displays [Source], [Resolution], [Software Version], [Color Space] and [Aspect Ratio].
41
English
User Controls
3D
Select [3D] from the Main Menu (see “How to
operate menu” on page 29) and then select the
item from the Sub Menu.
3D Invert
Flips the timing of the switch between the left and right
of an image to display. Change the setting if the 3D images you see appear strange.
1) Press ▲▼ to select [3D Invert].
2) Press ►, <Enter> to display the setting
dialog box.
3) Press ◄► to switch [On]/[Off].
On
Select when left and right 3D images are swapped to be displayed.
Off
If the 3D images are displayed
correctly, do not change the [Off]
settings.
3D Format
When [3D] is set to [On], it will compulsorily display the
3D setting mode.
3D
Use this function to set the display mode of the 3D
image.
1) Press ▲▼ to select [3D].
2) Press ►, <Enter> to display the setting
dialog box.
3) Press ◄► to switch.
On
Compulsory displays the 3D format
which is selected in [3D Format].
Off
Turn off [3D] image display.
Note
yy Compatible 3D source, 3D content and optional 3D
glasses type2 are required for 3D viewing.
yy When [3D] is set to [ON],[Picture]menu will change
to 3D setting in spite of the input signal, and [Color
Mode]or[Color Temp] can not be adjusted.
yy When viewing 3D contents, see [Note to Users Viewing 3D Images](→Page 14)
English
42
1) Press ▲▼ to select [3D Format].
2) Press ►, <Enter> to display the setting
dialog box.
3) Press ▲▼ to select the desired 3D Format
item.
4) Press ► to execute.
Side-bySide
Displays the Side-by-Side 3D
image in spite of the input signal
format.
Top and
Bottom
Displays the Top and Bottom 3D
image in spite of the input signal
format.
Frame
Sequential
Displays the Frame Sequential 3D
image in spite of the input signal
format.
Appendices
Lamp Replacement Procedure
If ceiling mounted, please use caution when opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must
be used to prevent any loose parts from falling out of projector.
Firmly install the lamp assembly as well as its cover.
If failing to install the lamp bulb smoothly, take it down and try again. If excessive force is
used when installing the bulb, the connectors may be damaged.
Do not disassemble any screws other than those specified.
Caution: If the lamp
should break, handle with
care to avoid injury due to
broken pieces and contact
your sales representative
for repair service.
Handle
Fixing screws of lamp
component
Lamp component
cover plate
Fixing screws of lamp component cover plate
1. Turn off the power in accordance with the procedures specified in the “Turning off the
Projector”. Unplug power cord from the power socket on the wall. Wait for at least one
hour until it is confirmed that the lamp components and its surroundings have been
completely cooled.
2. Unscrew the fixing screws of lamp components cover plate with cross head screwdriver,
and then open the lamp components cover plate.
● Slowly pull out the lamp components cover plate according to the direction of arrow.
3. Unscrew two fixing screws of lamp components with cross head screwdriver until the
screws are completely loose. Hold the handle, and gently pull up the lamp components
from the projector.
4. Insert the unused lamp components in the correct direction. Tighten the two fixing
screws of lamp components with cross head screwdriver.
5. Close the lamp components cover plate and tighten its fixing screws with cross head
screwdriver.
Reset the lamp usage time
After replacing the lamp components, reset usage time in [Clear the lamp usage time]
menu.
43
English
Appendices
Compatibility Modes
 Computer/Video/HDMI/Mac Compatibility
Please note that
using resolutions
other than native
1024 x 768 (native resolution of
this model) may
result in some
loss of image
clarity.
(*1) 1920 x1200
@60Hz only support RB (reduced
blanking).
120Hz input
signals may be
dependent on
graphics cards
support.
Signal
Resolution
Refresh Rate
(Hz)
Video
Analog
HDMI
Mac
NTSC
720 x 480
60
O
-
-
-
PAL/SECAM
720 x 576
50
O
-
-
-
640 x 480
60
-
O
O
O
640 x 480
67
-
O
-
-
640 x 480
72.8
-
O
-
O
640 x 480
85
-
O
-
O
800 x 600
56.3
-
O
-
-
800 x 600
60.3
-
O
O
O
800 x 600
72.2
-
O
O
O
800 x 600
85.1
-
O
O
O
800 x 600
120
-
O
O
-
1024 x 768
60
-
O
O
O
1024 x 768
70.1
-
O
O
O
1024 x 768
75
-
O
O
O
1024 x 768
85
-
O
O
O
1024 x 768
120
-
O
O
-
1024 x 600
60
-
-
O
O
1280 x 720
50
O
O
O
-
1280 x 720
60
O
O
O
O
1280 x 720
120
-
O
O
-
1280 x 768
60
-
O
O
O
1280 x 768
75
-
O
O
O
1280 x 768
85
-
O
O
O
1280 x 800
60
-
O
O
O
1366 x 768
60
-
O
O
-
1440 x 900
60
-
O
O
-
1280 x 1024
60
-
O
O
O
1280 x 1024
75
-
O
O
O
1280 x 1024
85
-
O
O
-
SXGA+
1400 x 1050
60
-
O
O
-
UXGA
1600 x1200
60
-
O
O
-
1920 x 1080
24
O
O
O
-
1920 x 1080
30
-
-
O
-
1920 x 1080
50
O
O
O
-
1920 x 1080
60
O
O
O
O
1920 x 1080
50
O
-
O
-
1920 x 1080
60
O
-
O
-
1920 x 1200
60 (*1)
-
O
O
O
VGA
SVGA
XGA
WSVGA
HDTV (720p)
WXGA
WXGA+
SXGA
HDTV (1080p)
HDTV (1080i)
WUXGA
English
44
Appendices
Signal
Resolution
Refresh Rate
(Hz)
Video
Analog
HDMI
Mac
SDTV (576i)
768 x 576
50
O
-
O
-
SDTV (576p)
768 x 576
50
O
-
O
-
SDTV (480i)
640 x 480
60
O
-
O
-
SDTV (480p)
640 x 480
60
O
-
O
-
HDMI 3D Input (with 3D Info Frame Information) -Video
3D mode
Input Resolutions
1280 X 720P @ 50Hz
Top and Bottom
1280 X 720P @ 60Hz
1920 X 1080P @24 Hz
1280 X 720P @ 50Hz
Frame packing
1280 X 720P @ 60Hz
1920 X 1080P @24 Hz
Side-by-Side(Half)
1920 X 1080i @50 Hz
1920 X 1080i @60 Hz
HDMI 3D Input (without 3D Info Frame information)
-Video
3D mode
Input Resolutions
1280 x 720P @50Hz
Side-by-Side(Half)
(SBS mode is on)
1280 x 720P @60Hz
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @50Hz
Top and Bottom
(TAB mode is on)
1280 x 720P @60Hz
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
VGA 3D Input -PC
3D mode
Side-by-Side (Half)
Top and Bottom
Frame Sequential
Input Resolutions
800x600 @ 60Hz
1024x768 @ 60Hz
800x600 @ 60Hz
1024x768 @ 60Hz
800x600 @ 120Hz
1024x768 @ 120Hz
Composite 3D Input
3D mode
Input Resolutions
HQFS
NTSC
45
English
Appendices
Troubleshooting
If you experience trouble with the projector, refer to
the following information. If the problem persists,
please contact your local dealer or service center.
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of terminals are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Ensure that the “AV Mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
Press “Auto Set” on the remote control.
Adjust the computer display settings. Verify the resolution setting
is less than or equal to 1600 x 1200 resolution. See your operating system’s Help file.
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the toggle output settings. example: [Fn]+[F3]
PANASONIC, NEC  HP, SHARP, TOSHIBA 
IBM, SONY  DELL, EPSON 
FUJITSU 
APPLE 
[Fn]+[F3]
[Fn]+[F5]
[Fn]+[F7]
[Fn]+[F8]
[Fn]+[F10]
[F7]
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
English
46
Appendices
The screen of the Notebook computer is not displaying a
presentation
If you are using a Notebook PC:
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s documentation for detailed
information.
Image is unstable or flickering
Adjust the “Phase” or “Clock” to correct it. Refer to the page 34.
Check and reconfigure the display mode of your graphic card to
make it compatible with the product.
Image is out of focus
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance.
(refer to pages 27 - 28)
The image is stretched when displaying 16:9 DVD
Change “Aspect” by pressing the key on remote control or OSD
menu to show image with proper aspect ratio.
Image is too small or too large
Move the projector closer to or further from the screen.
Press “Aspect” button on the remote control or press “Menu” button on the projector panel, go to “Position --> Aspect Ratio”.
47
English
Appendices
Image is reversed
Select “Position --> Ceiling Mount” from the OSD menu to adjust
the image.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp”.
Image does not display in 3D
Check if the battery of 3D glasses is drained.
Check if the 3D glasses is turned on.
3D Format is only supported on 3D Timing on page 45.
English
48
Appendices
Indicator lighting message
Message
No light 
<Temp>
indicator
<Lamp>
indicator
(Green/Amber)
(Red)
(Red)
Standby State
(Input power cord)
Amber
Power on (Warming up)
Flashing
Green
Lamp lighting
Steady light 
<Power>
indicator
Green
Power off (Cooling)
Flashing
Amber
Error (Over Temp.)
Flashing
Amber
Error (Fan fail)
Flashing
Amber
Error (Lamp fail)
Flashing
Amber
Flashing
49
English
Appendices
Maintaining the filter
We recommends cleaning the dust filter every three months;
clean it more often if the projector is used in a dusty environment.
Replacement of the air filters
Warning: If dust builds 1. Turn off the projector, and remove the AC power plug from
up on the filter is not
the AC outlet.
cleaned, the projector
2. Clean up the dust on the projector and around the air vents.
will overheat and cause
problems with the op- 3. Pull out the air filters straight and slowly with grabbing the
knobs.
eration and shorten the
life of the product.
Protrusion
Air filter (longer filter with
5 rows of intake vents)
Knob
Protrusion
Knob
Air filter (shorter filter with
3 rows of intake vents)
4. Install the new air filters (Replacement air filters).
• Hold the air filters with the protrusion up towards the top panel
as shown in the picture and insert them until you hear a “click”
sound.
5. Reset the [Filter Reminder].
• Turn on the power and perform [Cleaning up Reminder] in the
[Options] menu.
English
50
Appendices
Configurations of Terminals
Terminal: Computer in 1/2 [Monitor Out]
(Mini D-sub 15 pin)
5
4
3
10
15
9
14
2
1
8
13
7
12
6
11
1
Red (R/Cr) Input [R Output]
9
DDC 5V [NC*]
2
Green (G/Y) Input [G Output]
10
Ground (Ver. sync.)
3
Blue (B/Cb) Input [B Output]
11
NC*
4
NC*
12
DDC Data [NC*]
5
Ground (Horiz.sync.)
6
Ground (Red)
13
Horiz. sync. Input [Output]
(Composite H/V sync. Input)
7
Ground (Green)
14
Vert. sync. Input [Output]
8
Ground (Blue)
15
DDC CLK [NC*]
* Do not connect anything.
Terminal: PC Control (D-sub 9 pin : female)
6
1
1
Contact your
dealer for control
cable and commands.
7
2
8
3
9
4
5
NC*
6
NC*
2
TXD (Sending Data)
7
NC*
3
RXD (Receiving Data)
8
NC*
4
NC*
9
NC*
5
GND
* Do not connect anything.
51
English
Appendices
Specifications
List of general specifications
Designs and
specifications are
subject to change
without notice.
This model may
not be compatible with features
and/or specifications that may
be added in the
future.
English
52
Specification
Consumption Power
240W (ECO mode) / 295W (Full mode)
Weight
2.8kg
Dimensions (WxHxD)
220 x 288 x 100 mm (with protruding parts)
Environmental Considerations
Operational Temperatures : 41° to 95°F (5° to 35°C),
20% to 80% humidity (non-condensing) Storage
Temperatures : -4° to 140°F (-20° to 60°C), 20% to 80%
humidity (non-condensing)
Projection System
Single DLP® 0.55” chip
Resolution
1024 × 768 pixels (XGA)
Lens
F#2.8, f=7.26mm
Lamp
High-pressure mercury lamp (240W)
Lamp Life
3500hours typical (Full Mode) / 5000 hours typical
(ECO1/ECO2 Mode) / 10000hours typical (Auto Mode)
Projection screen size
40 - 200 inch
Projection distance
0.51 - 2.54m (Focus range)
Speaker
8W (Mono)
Computer In terminal× 2 Mini D sub 15 pin RGB / Y/PB / PR (dual use)
Connection terminal
This model
complies with the
above specifications.
Item
Monitor Out terminal
Mini D sub 15 pin
HDMI terminal
HDMI
Video terminal
RCA Pin Jack
PC Control terminal
D sub 9 pin Female (RS-232C compliant)
Audio In terminal × 2
3.5mm diameter mini-jack (1) Computer 1 or Computer
2 (2) Video
Audio Out terminal
3.5mm diameter mini-jack
Appendices
Cabinet Dimensions
220.09
Unit: mm
288.0
70.8
48.04
42.7
75.28
82.3
157.58
64.0
55.0
55.0
Screw type: M3 x 3
Maximum screw length: 6mm
53
English
Appendices
Trademarks
• DLP is trademark or registered trademark of Texas
Instruments.
• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Macintosh, Mac OS X, iMac, and PowerBook are trademarks of Apple Inc., registered in the U.S. and other
countries.
• Microsoft, Windows, Windows Vista, Internet Explorer
and PowerPoint are either a registered trademark or
trademark of Microsoft Corporation in the United States
and/or other countries.
• HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• Other product and company names mentioned in this
user’s manual may be the trademarks or registered
trademarks of their respective holders.
• Blu-ray is a trademark of Blu-ray Association.
English
54
EN GB
EN US
EN AU
Y057-6221B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement