Advertisement
Advertisement
HYDRAULIC GARAGE JACK OPERATION MANUAL NO.9TY132 Enjoy your work 3 KT NO. Capacity (T) Min height (mm) Max height (mm) 9TY132-03A-B 3 130 465 9TY132B-03A-B 3 140 520 READ ALL INSTRUCTIONS BEFORE USE • Study, understand, and follow all instructions before operating this device. • Failure to heed these markings may result in serious personal injury and / or property damage. • Prior to each use, visual inspection shall be made to the device by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts. • Do not exceed the rated capacity stated. • Use only on hard level surfaces. • This item is to be used as a lifting device only. Immediately support the vehicle with appropriate rated jack stands after lifting. • Do not move the vehicle while it is on the jack. • Lift only on areas of the vehicle as specified by the vehicle manufacturer. • No alterations shall be made to this product. LIFTING • Turn the handle/release valve clockwise to the closed position. Do not over tighten. • Position the jack under the specified lift point. • Begin lifting by pumping the handle up and down. • Immediately support the vehicle with appropriately rated jack stands after lifting. • Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack stands. LOWERING • Turn the handle/release valve clockwise to the closed position. Do not over tighten. • Pump the handle up and down to lift vehicle off jack stands. • Remove the jack stands. Do not get under or let anyone get under the vehicle while lowering. • Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the ground. MAINTENANCE CHECK AND REFILL OIL : • With the jack in the fully lowered level position, if unit cover is provided, remove unit cover, then remove oil filler plug. • Proper oil level should be just cover inner cylinder as seen from the oil filler plug hole. • Do not overfill. Always fill with new, clean hydraulic jack oil as recommended above. • Reinstall oil filler plug, then reinstall unit cover. NOTICE : Use high grade hydraulic oil only. Never use brake fluid, motor oil, transmission fluid,turbine oil or any other fluids. LUBRICATION AND CLEANING • Periodically clean and lubricate all moving parts and pivot points. AIR VENTING PROCEDURES • With the jack in the fully lowered position, unlock release valve, remove oil filler plug. • Pump the handle rapidly several mins. Reinstall oil filler plug. • Turn the handle/release valve clockwise to the closed position. • Pump the handle until the arm reaches maximum height and continue to pump several mins. to remove trapped air in the system. • Turn the handle/release valve counterclockwise in one full turn and lower arm to the lowest position. Use force on saddle if necessary. • Carefully and slowly loosen oil filler plug to release pressurized air. • Repeat above steps until trapped air is completely vented. INSPECTION • Visual inspection shall be made before each use of the device by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts. • This device shall be inspected immediately if the device is believed to have been subjected to an abnormal load or shock. TROUBLESHOOTING Problems Causes Solutions Jack will not lift the load. 1. Tighten release valve. 1. Release valve not tightly closed. 2. Check and add oil. 2. Low oil level. 3. Discontinue use and contact a local 3. Defective or worn internal parts. repair center. 4. Load exceeds maximum allowance. 4. Use a higher capacity jack. Jack will not hold the load. 1. Release valve not tightly closed. 2. Power unit malfunction. 1. Tighten release valve. 2. Discontinue use and contact a local repair center. Jack will not descend to minimum height, or will not remain in lowered position. 1. Air trapped in system. 2. Reservoir oil overfilled. 1. Check and ensure proper oil level. 2. Vent air out of system. Follow “AIR VENTING PROCEDURES” instructions. Jack will not lift to max height. 1. Low oil level. 1. Check and ensure proper oil level. 2. Follow “MAINTENANCE” instructions. Jack will not function 1. Internal malfunction or properly after trying solution. structural damage. 1. Discontinue use and contact a local repair center. PARTS LIST Qty Part 1 Side. plate weldment Description 1 22 Lock washer 2 2 2 23 Bolt 1 3 Caster assembly Locknut 2 24 Bolt 1 4 Wheel 2 25 Torsion spring 1 5 Washer 2 26 Valve gear 1 6 Retaining ring 2 27 Plunger pin 1 7 Power unit assembly 1 28 Gear shaft 1 8 Socket head cpa screw 2 29 Cotter pin 1 9 Split lock washer 2 30 Washer 1 10 Lift arm assembly 1 31 Gear Head screw 1 11 Shaft arm 1 32 Lock washer 1 12 Saddle 1 33 Hex nut 1 13 Grease fitting 1 34 Handle bolt 1 14 Bolt 2 35 Stud 1 15 Retaining ring 1 36 Handle, lower 1 16 Block link 1 37 Handle, upper 1 17 Cotter 1 38 Hex head screw 1 18 Return spring 1 39 Handle socket 1 19 Retaining ring 2 40 Lock washer 1 20 Lock washer 2 41 Lock washer 1 21 Nut 2 Part Description www.kingtony.com customer service e-mail : [email protected] 899TY132-KT 297x210mm Qty ">

Public link updated
The public link to your chat has been updated.
Advertisement