HT3 User Manual

HT3 User Manual
User and Installation Instructions
Silverlink 600 Electric Boiling Tops
HT3, HT6, HT7
Part No. IS220 ECN2558
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE EQUIPMENT.
KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.
WARNING:
APPLIANCES MUST BE EARTHED
ISOLATE THE POWER SUPPLY BEFORE CARRYING OUT ANY INSTALLATION OR
SERVICE WORK
PARTS OF APPLIANCES BECOME HOT DURING NORMAL USE. CARE SHOULD BE
TAKEN TO AVOID ACCIDENTAL BURNS
IMPORTANT
All Lincat electrical appliances must be installed, operated and serviced by a competent person. Users
should take care to adopt safe working practices when operating or cleaning appliances. Please contact
your local distributor for further advice.
INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
Ensure that the electricity supply is adequate for the equipment being installed.
Partitions, walls, kitchen furniture and other materials less than 100mm from the appliance should
be made from non-combustible material.
Remove all protective plastic coating from the unit.
When siting the equipment, make sure that it is level and that there is a free flow of air around the
unit and that any vents to the rear are not blocked.
All appliances with an electric load of 3kW and below are fitted with a BS1363 fused plug and
should be connected to an earthed socket.
Appliances above 3k must be connected to the supply by a qualified electrician and should be
installed with a means of isolation with contact separation of at least 3mm on all poles.
Appliances must be installed in accordance with the Health and Safety at Work Act, IEE Wiring
Regulations, BS Codes of Practice, Local and National Building Regulations and Fire Precautions
Act 1971
When fitting countertop units onto SLS stands, the feet should be located into the corresponding
holes in the base units. When fitting onto Ovens, HC pedestals or similar closed bases, the feet can
be removed if required.
GENERAL USE
Unless otherwise stated in the equipment instructions, the following convention applies where indicator
lights are fitted to appliances:Green on - power to unit.
Amber on - power to element.
Amber off - temperature reached.
Part No. IS220 ECN2558
USER MAINTENANCE
1.
2.
3.
Before working on or cleaning the equipment, isolate it from the power supply and allow it to
cool to a safe working temperature.
Clean units regularly with hot water and detergent, do not use abrasive or chlorine based cleaners
on stainless steel. Take care to avoid wetting electrical components. Do not use a water jet.
For removing carbon deposits from fryers and griddles use "Carb'n'Off" or a similar
proprietary cleaner.
BOILING TOPS
HT3, HT6, HT7
PREPARATION
1.
Before first use, burn off the protective coating on the hotplates by heating them on maximum,
without a pan, for 3-5 minutes and then wipe clean when cool.
2.
For maximum efficiency, use good quality pans of adequate size with stable, slightly concave
bottoms
OPERATION
1.
Switch on the mains supply and the green neon will illuminate.
2.
Adjust the temperature to the desired level by means of the control knob.
3.
Each plate incorporates a protection device that automatically reduces the power when the pan is
removed or if a pan boils dry.
Part No. IS220 ECN2558
SERVICE INFORMATION
Catering equipment should be routinely serviced to ensure a long and trouble free life. With this in mind it
is recommended that appliances are serviced every six months by a competent engineer.
For help regarding the installation, maintenance and use of your Lincat equipment, please call:-
LINCAT SERVICE HELP DESK
01522 875520
AUTHORISED SERVICE AGENTS
We recommend that all servicing, other than routine cleaning, is carried out by our authorised service
agents and will accept no responsibility for work carried out by other persons. Note that for safe and
efficient operation, appliances need regular servicing.
Please quote both the model and serial numbers from the data plate attached to the unit. Give brief details
of the service requirement.
Lincat reserve the right to carry out any work under warranty during normal working hours, i.e. Monday
to Friday, 8.30 a.m. - 5.00 p.m.
CONDITIONS OF GUARANTEE
The guarantee does not cover: 1.
2.
3.
Accidental breakage or damage
Operational misuse, wear and tear from normal usage, incorrect adjustment and neglect.
Incorrect installation, maintenance, modification or unauthorised service work.
Part No. IS220 ECN2558
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising