WIRELESS LED KEYPAD

WIRELESS LED KEYPAD
WIRELESS LED KEYPAD
EKB3W
User Manual v1.2
Compatible with:
• ESIM364 all versions.
• EPIR2 all versions.
• EPIR v05.06.02 and up + EWT2 v16.17 and up.
Main features:
•
•
•
•
•
•
•
Alarm system arming & disarming;
Stay mode activation & deactivation;
System parameter configuration;
PGM output control;
Visual indication by LED indicators;
Audio indication by built-in mini buzzer;
Keypad partition switch.
EKB3W is a wireless LED keypad intended to use with ELDES alarm systems. The system configuration by EKB3W keypad is performed
by activating the Configuration Mode and entering the required parameters & values. ELDES alarm systems allow to connect up to
4 EKB3W keypads.
NOTE: For complete system configuration & control using EKB3W keypad, please, refer to ELDES alarm system installation manual
located at: www.eldes.lt/en/download
1. Package Content
1. EKB3W .................................................................................qty. 1
2. User manual.......................................................................qty. 1
3. 5,6kΩ resistor.....................................................................qty. 1
2. Technical Specifications
2.1 Electrical & Mechanical Characteristics
Battery Type
1,5V Alkaline AAA type
Number of Batteries
3
Battery Operation Time
~12 months*
Wireless Transmitter-Receiver Frequency
868 Mhz
Range of Operating Temperatures
-30...+55ºC
Dimensions
140 x 100 x 18 mm
Wireless Communication Range
Up to 30 meters in premises; up to 150 meters in open areas
Compatible with Alarm Systems
ELDES Wireless
* This operating time may vary in difference conditions.
2.2 LED Functionality
2
ARMED
Security system is armed / Configuration mode
READY
System is ready – no violated zones and tampers
SYSTEM
System troubles / valid command is being entered
BYPS
Zone bypass mode
1-12
Violated zone
2.3 Keys Functionality
[BYPS]
Zone bypass mode
[CODE]
Additional options - system trouble list / violated high-numbered zone indication / violated tamper indication
[*]
Configuration mode (when typed as a 1st character) / cancel command (when typed as a 2nd character) / keypad
partition switch (if enabled)
[#]
Confirm (enter) command
[0] ... [9]
Command typing
[STAY]
Manual Stay mode activation
[INST]
(currently inactive)
2.4 Main Unit & Connector Functionality
BACK SIDE
FRONT SIDE
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
5
6
10
11
12
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
+
BATTERY
-
-
BATTERY
+
+
BATTERY
-
TAMPER
5,6 kOhm
Z1 COM
Fig. No. 1
TAMPER
+/-
Fig. No. 2
Tamper-button for EKB3W
enclosure status monitoring
Battery slots
COM
Common terminal
Z1
Security zone terminal
3. Installation
1. Detach keypad holder from EKB3W front side . Keypad holder detach points are marked with arrows (see Fig. No. 3).
DOWN SIDE
BACK SIDE
Fig. No. 3
USER MANUAL EKB3W V1.2
3
2. Fix the keypad holder on the wall using the screws.
3. Z1 and COM contacts must be connected with resistor of 5,6kΩ nominal (see Fig. No. 2). As keypad zone Z1 is disabled by default,
it can be enabled by SMS, EKB3W keypad and ELDES Configuration Tool software. Keypad zone Z1 must be enabled and resistor
connected even if the tamper button alone is required.
4. Remove the plastic tab inserted between one of the battery terminals and battery slot contacts (see Fig. No. 4).
Fig. No. 4
ATTENTION! Before fixing the keypad into the holder, please, make sure that the tamper is properly pressed (see Fig. No. 2).
5. Bind the device to the alarm system using ELDES Configuration Tool software. Open Wireless Device Management section and
enter a 8-digit wireless device ID located on the EKB3W enclosure and press Add button (see Fig. No. 5). The device can also be
bind by sending a corresponding command via SMS message. For more details, please, refer to the software‘s HELP section and
ELDES alarm system installation manual.
Fig. No. 5
7. Upon the successful binding process, the built-in mini buzzer of EKB3W device provides 3 short beeps and EKB3W icon, Battery
Level and Signal Level becomes visible in ELDES Configuration Tool software’s Wireless Device Management section. If attempt
to bind is unsuccessful, try to move EKB3W closer to the alarm system device and bind anew.
8. EKB3W keypad is ready for use.
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try
again. See chapter 6. Restoring Default Parameters for more details.
4
4. EKB3W Zone & Tamper
Upon successful EKB3W wireless LED keypad contact binding process, the system adds 1 wireless Instant zone intended for wired
sensor connection. In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways
to detect tamper violation on EKB3W:
• By tamper button. EKB3W has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure
of EKB3W is illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS
message and phone call to the user (-s) by default. The SMS message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EKB3W and ELDES alarm system leads to alarm. The
system identifies this event as a tamper violation and sends alarm by SMS message and phone call to the user (-s) by default.
The SMS message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper
alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
5. Battery Replacement
1. Open EKB3W enclosure.
2. Remove all 3 old batteries from the battery slots.
1. Postition the 3 new 1,5V alkaline AAA type batteries according to the appropriate battery slot positive/negative terminals indicated on the PCB (printed-circuit-board) of EKB3W.
2. Insert the batteries into the battery slots.
3. Batteries replaced.
See chapter 3. Installation for more details.
ATTENTION: Only 1,5V Alkaline AAA type batteries can be used. Install only new, high quality and unexpired batteries. Do not
mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must
be taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not
charge, disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
6. Restoring Default Parameters
1. Remove one battery from EKB3W.
2. Press and hold the [*] key.
3. Insert the battery back to EKB3W.
4. Hold the [*] key until LED READY starts flashing.
5. Wait until LED READY turns off and LED ARMED starts flashing.
6. Release the [*] key.
7. Parameters reset to default.
USER MANUAL EKB3W V1.2
5
7. Additional Information
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against such
events.“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system. “ELDES
UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any of the
Internet providers therefore is not responsible for the quality of Internet service.
Manufacturer Warranty
This device carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been
purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the
manual and within specified operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided if the
system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environment or other
force majeure factors.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates
that the product must not be disposed of together with household waste. To prevent possible harm to human health
and/or the environment, the product must be disposed on in an approved and environmentally safe recycling process.
For further information on how to dispose of this product correctly, contact the system supplier, or the local authority
responsible for waste disposal in your area.
6
Copyright © “ELDES UAB”, 2013. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written
authorization by “ELDES UAB”. “ELSDES UAB” reserves the right to update or modify this document and/or related products
without a warning. Hereby, “ELDES UAB” declares that this wireless LED keypad EKB3W is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at
www.eldes.lt
USER MANUAL EKB3W V1.2
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement