BaoFeng BF-888S

BaoFeng BF-888S
BaoFeng BF-888S
User Manual
A
LED Indicator
Lights red during transmit, green when receiving a signal
B
Channel Switch
Rotate to select a channel. No. 16 is the scanning channel
C
Power Switch / Volume Control
Turn clockwise to switch ON the transceiver.
Turn counterclockwise to switch OFF transceiver.
Rotate to adjust volume.
D
PTT (Push-to-Talk) Button
Push button to transmit.
Release to receive.
E
MONI (Monitor) Button
Press and Hold (Squelch OFF) to hear background noise; Release to
return to normal operation.
F
FUNC (Function Button) Button
Press to activate LED torch function.
G
Speaker Microphone / Programming Cable Jack
OPERATION
Switching Power ON/OFF
Turn the Power switch/Volume control (A) clockwise. You will hear a beep and
speech indicating the transceiver is ON.
Adjusting the Volume
Hold Monitor button (E) own to listen to audio level while rotating the Power
switch/Volume control (A). Rotate Volume Control to increase / decrease the
volume.
Selecting the Channel
Turn the Channel Switch (B) to the desired channel. No. 16 is the Scanning
Channel.
Transmitting
To transmit, Press and Hold PTT (D) and speak into the microphone in a normal
tone of voice.
The LED indicator lights continuously red when transmitting.
For maximum sound clarity at the receiving station, hold the transceiver 2 to 3
inched from mouth and talk in a normal tone of voice.
Note: Yelling does not make your signal louder.
CHARGING the LI-ION BATTERY PACK
Charge the battery pack before using it. The new or stored (more than 2
months) battery pack cannot reach full capacity after the first charge. After 2 or
3 charges and discharges, it will reach full charge.
1. Plug adapter into electrical socket.
2. Insert transceiver or battery into the charging tray.
3. Ensure that the battery contacts connect with the drop-in charging tray.
While charging is taking place, the LED will glow Red.
4. After 3 hours charging, the LED indicator will light Green.
5. Remove battery or transceiver from the charging tray.
Asterisk [ * ] designates function changed via software
* SQUELCH LEVEL
The purpose of the Squelch is to mute the speaker when no signals are present. With
the squelch correctly set, you will only hear sound when a signal is present.
* TIME-OUT TIMER (TOT)
The TOT limits the length of a users transmission. The purpose of the TOT is to
prevent transmitting for a long period of time, causing thermal damage to the radio.
And alert will sound when the limit for that transmission has been reached.
* SCANNING
Scanning is used for hands off monitoring of your favorite frequencies. When the
transceiver options are set to SCAN (via software), setting the channel selector to
channel 16 directs the radio to scan the selected channels from 1-15.
1. Transceiver stops scanning when a signal is detected and continues when signal is
gone.
2. If there are less than 2 channels, it cannot scan. (Go figure)
3. On channel 16, Press and Hold the PTT and MONI buttons while switching ON the
transceiver to turn the Scanning ON or OFF.
4. If FM radio function is activated, Radio cannot scan.
* VOICE PROMPT
1. VP can be set ON/OFF via software.
2. On channel 10, Press and Hold the PTT and MONI buttons while switching ON the
transceiver to also Activate or Deactivate Voice Prompt.
3. On channel 15, Press and Hold the PTT and MONI buttons while switching ON the
transceiver to change Voice Prompt Language (CHI / ENG)
4. Any channel 1-16, Press and Hold MONI only while switching ON the transceiver
will Deactivate Voice Prompt for that session only.
* VOX (Voice Operated Transmit)
VOX eliminates the need for using the PTT key to transmit. The transmitter is keyed
when the VOX circuit senses you are speaking into the microphone.
1. When operating the VOX function, set the VOX Gain level to recognize the
desired sound level.
2. If level is too sensitive, transceiver will key with noise in the background.
3. If level is not sensitive enough, it will not pick up your voice. Set level for smooth
transmission.
4. On channel 1-5, Press and Hold the PTT and MONI buttons while switching ON
the transceiver to turn the VOX ON or OFF.
* EMERGENCY ALARM
On channel 11, Press and Hold the PTT and MONI buttons while switching ON the
transceiver to turn the Alarm Function ON or OFF.
This is a function for your receiver only. You will Not transmit the alarm.
BATTERY SAVER
Reduces the battery power used when not receiving a signal. Battery saver turns on
automatically 10 seconds after no signal is received and no operation is being
performed.
BATTERY LOW ALERT
Reminds you that battery needs recharging. Alert tone will sound and Red LED will
blink.
MONITOR
When no signal is being received, Press and Hold the MONI. This is helpful for
adjusting volume level and receiving weak signals.
* BUSY CHANNEL LOCK-OUT (BCL)
BCL prevents you from transmitting on a channel if a signal is present. Pressing the
PTT switch while a channel is in use will emit an alert tone and inhibit the transmitter.
* BEEP TONE
If turned on, radio will give short tone to indicate that there is nothing programmed
for that channel.
* CTCSS / DCS
CTCSS (Continuous Tone Coded Squelch System) or
(Digital Coded Squelch).
CTCSS / DCS Description
You may sometimes want to hear calls only from specific persons or groups. This
option allows you to ignore unwanted calls from others on the same frequency. These
tones are sub-audible (cannot be heard) and are selectable via software.
Note: These tones do NOT cause your conversation to be private or scrambled. It only
relieves you from listening to unwanted conversations.
SUMMARY of FUNCTION ACTIVATION
Ch 1-5, Press / Hold both PTT and MONI, and Power ON
VOX - ON / OFF.
Ch 10, Press / Hold both PTT and MONI, and Power ON
Voice Prompt - ON / OFF
Ch 11, Press / Hold both PTT and MONI, and Power ON
Alarm Function ON / OFF (if selected via SW)
Ch 15, Press / Hold both PTT and MONI, and Power ON
Change Language (CHI / ENG)
Ch 16, Press / Hold both PTT and MONI, and Power ON
Scan ON / OFF (if option set via software)
Ch 1-16, Press / Hold MONI only and Power ON
Deactivates Voice Prompt for that session only.
SPECIFICATIONS
Frequency Range
RF Rated Power
Channel Capacity
Operating Voltage
Dimensions
400 - 470MHz
<= 5W
16
3.7V
115mm x 60mm x 33mm
4.53" x 2.36" x 1.30"
150g (5.3oz)
Weight
TROUBLESHOOTING GUIDE
No Power
Can't
communicate
with other
members
Hearing other
stations
I can clearly hear
members of my
group, but my
voice is
Check Battery Installation and/or replace/charge battery.
Verify that the frequency and CTCSS tones are the same
for all members. If all checks out okay, make sure you are
all within range.
Change your CTCSS for that channel. Change to another
channel.
Check if microphone is blocked. If so, return radio to
dealer for maintenance. Sometimes your frequency is the
same as the frequency of other groups.
intermittent.
Can't turn on the
radio, or it turns
on and quickly
shuts down.
Check the battery contacts on the radio. If they are broken
or twisted, return your radio to an authorized dealer for
maintenance.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement