ENDA EI141 PROGRAMMABLE INDICATOR

ENDA EI141 PROGRAMMABLE INDICATOR
english
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
ENDA EI141 PROGRAMMABLE INDICATOR
Thank you for choosing ENDA EI141 INDICATOR.
* 35x77mm sized.
* 4 digits display.
* Easy to use by front panel keypad.
* Display scale can be adjusted between -1999 and 4000.
* Decimal point can be adjusted between 1. ile 3. digits.
* Measurement unit can be displayed.
* Selectable four different standard input types (0-20mA, 4-20mA, 0-1V, 0-10V)
* User can calibrate the device according to his/her own specified input type.
* Sampling time can be adjusted in four steps.
* Maximum and minimum measurement values are registered.
* The maximum or the minimum values can be hold on the display.
* Current and voltage calibration can be made..
* Parameter access protection on 3 levels.
* Easy connection by removable screw terminal.
PROGRAMMABLE INDICATOR
SET
ENDA
EI141
1 - Supply Voltage
230VAC...230V AC
24VAC.....24V AC
SM...........9-30V DC / 7-24V AC
Order Code : EI141-
1
TECHNICAL SPECIFICATIONS
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature 0 ... +50°C/-25 ... +70°C (with no icing)
80% up to 31°C decreasing linearly 50% at 40°C.
Max. relative humidity
According to EN 60529
Front panel : IP65
Rated pollution degree
Rare panel : IP20
Height
Max. 2000m
Do not use the device in locations subject to corrosive and flammable gases.
up to date: 03072010, modification reserved and can be change any time previous notice !
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Date retention
EMC
Safety requirements
230VAC +10%/-20%, 50/60Hz, 24VAC±10%,50/60Hz or 24Vac/dc (9-30Vdc or 7-24Vac)
Max. 7VA
2.5mm² screw-terminal connections
EEPROM (Min. 10 years)
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B for the EMC standard)
EN 61010-1: 2001 (pollution degree 2, overvoltage category II, measurement category I)
EI141 must not be used in location where measurement category is II, III or IV.
Input type
0-1V DC voltage
0-10V DC voltage
0-20mA DC current
4-20mA DC current
Measurement range Measurement accuracy
Min.
Max.
0V
0V
0mA
0mA
1.1V
14V
25mA
25mA
±0,5% (of full scale)
±0,5% (of full scale)
±0,5% (of full scale)
±0,5% (of full scale)
Input empedance
Approx. 11kW (terminal voltage limits: min. = -2V, max. = 30V)
Approx. 11kW (terminal voltage limits: min. = -2V, max. = 30V)
Approx. 5W (applicable terminal voltage is max. 50mA.)
Approx. 5W (applicable terminal voltage is max. 50mA.)
In the current measurement mode input impedance is 5W. Therefore, in the current measurement mode, any voltage input
should not be connected to the input terminals. Otherwise, the device will be broken down. To change the input type from
voltage to a current measurement mode while the device is operating, first, leave out the voltage inputs. Then, change
input type to one of the current measurement modes.
HOUSING
Housing type
Dimensions
Weight
Enclosure material
Suitable for flush-panel mounting according to DIN 43 700.
W77xH35xD71mm
Approx. 250g (after packing)
Self extinguishing plastics
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
SURAN Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N
Tel.: +49 (0)7451 / 625 617
Fax: +49 (0)7451 / 625 0650
E-mail : [email protected]
Internet : www.suran-elektronik.de
1./3
EI141-E
TERMS
1) Measurement value, measurement unit, the minimum or the maximum measured values are
displayed in the run mode.
Parameter name, parameter value or a user defined unit is displayed in the programming mode.
PROGRAMMABLE INDICATOR
2) Increment or parameter selection key in the programming mode.
Used for displaying measurement unit or the max. measured value in the run mode.
SET
ENDA
3) Decrement or parameter selection key in the programming mode.
Used for making the minimum and the maximum measured values equal in the run mode.
EI141
4) Used for selecting run and programming modes, adjusting parameters, displaying
measurement unit or making the minimum and the maximum measured values equal.
( 1 ) Digital display
4 digits 7 segment yellow LED display
9.1mm
Character height
( 2 ),( 3 ),( 4 ),( 5 ) Keypad
Micro switch
DIMENSIONS
Panel
77mm
For removing mounting clamps:
- Push up the flush-mounting
clamp in direction 1 as
shown in the figure above.
- Then, pull out the clamp in
direction 2.
35mm
PROGRAMMABLE INDICATOR
SET
ENDA
71mm
EI141
5mm
2
Flush mounting
clamp
Rubber
packing
1
Flush mounting
clamp
2
3
4
5
6
7
8
9 10 11 12
230V AC +10%-20%
50/60Hz 7VA
GND
+
INPUT
1
Panel
Panel cut-out
Note : 1) Panel thickness should be maximum 7 mm.
2) If there is no 60mm free space at the back
side of the device, it would be difficult to
remove it from the panel.
71mm
EI141-230VAC
PROGRAMMABLE INDICATOR
SN: XXXXXXXXX
29mm
ENDA INDUSTRIAL ELECTRONICS
CONNECTION DIAGRAM
ENDA EI141 is intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding must be
grounded on the instrument side. During an installation, all of the cables that are connected to the device must be free of energy. The device
must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. All
input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be
close to the power cables or components. The installation and electrical connections must be carried on by a qualified staff and must be
according to the relevant locally applicable regulations.
ENDA INDUSTRIAL ELECTRONICS
ENDA INDUSTRIAL ELECTRONICS
ENDA INDUSTRIAL ELECTRONICS
EI141 PROGRAMMABLE INDICATOR
EI141-24AC PROGRAMMABLE INDICATOR
EI141-24DC PROGRAMMABLE INDICATOR
4
5
6
7
8
NOTE :
SUPPLY :
184-253V AC 1
50/60Hz 7VA 2
Line
Neutral
Fuse
F 100 mA
250V AC
2
3
4
5
6
7
8
2
Switch
230V AC
Supply
Fuse should
be connected
Holding screw
0.4-0.5Nm
GND
1
3
4
5
6
7
8
+
INPUT
9 10 11 12
GND
1
9 10 11 12
24V DC ±10%
7VA
24V AC +10% -20%
50/60Hz 7VA
GND
+
INPUT
3
+
2
SN: XXXXXXXXX
+
INPUT
1
SN: XXXXXXXXX
-
230V AC +10% -20%
50/60Hz 7VA
SN: XXXXXXXXX
9 10 11 12
Equipment is protected throughout
by DOUBLE INSULATION.
Cable size: 1,5mm²
Note : 1) Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it should be
easily accessible by the operator.
2./3
EI141-E
Bar.
&
SET
then,
then, by using
H.inp.
l.inp.
The minumum
measured value
then
keys are pressed together and held until
‘CAL' message appears. See NOTE 2.
To initialize calibration, first
SET
At this state, the reference voltage or
current that corresponds to H.SCL.
parameter is applied to the input.
keys are pressed together and held until ‘CAL'
message appears. See NOTE 2.
SET
At this state, the reference voltage or
current that corresponds to L.SCL. Parameter
is applied to the input.
To initialize calibration, first
then
It can be adjusted between (L.SCL. +100)
and 4000.
See NOTE 1 for programming.
H.SCL. = Upper limit for scale.
L.SCL. = Lower limit for the scale.
It can be adjusted between -1999 and
(H.SCL. -100).
See NOTE 1 for programming.
Decimal point can be adjusted between
1. and 3. digits or without dp.
See NOTE 1 for programming.
d.Pnt. = Decimal point.
CAL.t. = Calibration type.
Selectable as S.inP. or U.inP.
If S.inp. is selected, input type is one the
four standard input types. If U.inP is
selected, input types can be modified.
See NOTE 1 for modification.
Programming Mode
870
CAL.
NOTE 2
SET
keys are pressed together and held until ‘CAL'
message appears. See NOTE 3.
SET
At this state, 10.000V is applied to the input of
the device.
To initialize calibration, first
then
10.CA. = 10V input calibration.
keys are pressed together and held until ‘CAL'
message appears. See NOTE 3.
SET
1.CA. = 1V input calibration.
At this state, 1.0000V is applied to the input of
the device.
To initialize calibration, first
then
appears for 1 seconds and the program
is shifted to the next step.
C.err.
If calibration is error free, the message
appears for 1 seconds. However,
if it is wrong, the message C.Err.
appears for 1 seconds and the program
is shifted to the next step.
C.End
3./3
EI141-E
If the reference voltage or current applied to the input for calibration is too high or too low, this error message appears.
No
C.err.
C.end
Yes
CAL okey?
The message on the left flashes approximately 5
seconds and calibration is completed.
d.Ca.S. = d.CAL. menu protection level
parameter.
nonE = No menu is seen.
P. no = Menu is seen but can not be programmed.
P.yES. = Menu is seen and programming is possible.
See NOTE 1 for programming.
See NOTE 1 for programming.
nonE = No menu is seen.
P. no = Menu is seen but can not be programmed.
P.yES. = Menu is seen and programming is possible.
Uo.Sc. = U.oPt. menu protection level
parameter.
See NOTE 1 for programming.
nonE = No menu is seen.
P. no = Menu is seen but can not be programmed.
P.yES. = Menu is seen and programming is possible.
d.C.Sc. = ConF. menu protection level
parameter.
s.Cod. = Access code for safety menu.
This parameter should be 333.
See NOTE 1 for programming.
S.err.
ERROR MESSAGES
s.err.
If calibration is error free, the message
C.End appears for 1 seconds. However,
if it is wrong, the message S.Err.
CAL.
NOTE 3
D.Ca.s.
Uo.sc.
d.C.sc.
S.Cod.
SeCU.
If the difference between the reference voltages or currents applied for the calibration of H.inP. and L.inP. is lower than one
half of the full scale, this error message appears on the display.
For example: Assume that the selected input type is 0-1V. In this case, if the difference between the reference voltages
applied for calibration of H.inP.and L.inP. is lower than 0.5V, this error message appears.
C.end
then
keys are pressed together and held until ‘CAL'
message appears. See NOTE 3.
For initializing calibration, first
SET
A.CAL. = Current calibration.
At this state, 20.000 mA current is applied to the
input of the device.
s.Cod. = Access code for calibration menu.
This parameter should be 222.
See NOTE 1 for programming.
The message on the left flashes approximately 5
seconds and calibration is completed.
No
10.CA.
1.CA.
a.CAL.
Yes
Res.
SET
If first
and then
keys are
pressed together, the maximum and
the minumum measurement values
become equal to the measured value at
that time and the message res.
appears on display.
If no key is pressed within 20 seconds during programming mode data is stored automatically and the run
mode is entered. Alternatively the same function occurs by pressing
key and holding for 5 seconds
S.Cod.
CAL
CALokey?
okey?
The maximum
measured value
Pressing this key the maximum
measured value up to that time
appears
SET
Entering from programming mode to run mode:
1453
d.Cal.
Pressing this key the minumum
measured value up to that time
appears.
Running Mode
For adjusting a selected parameter first press and hold
key. Then, by using
keys adjustment
can be made.
If increment key
is pressed and held 0.6 seconds, the value of the selected parameter changes rapidly.
If
SET
Evet
CAL.t.=U.ýnP.
H.sCl.
l.sCl.
d.pnt.
Cal.t.
U.opt.
Parameter adjustment method
key decimal point can be
keys are pressed and held together. And
For including decimal point first,
A constant, a message etc. to be displayed
can be entered. If a decimal point is desired,
it should be included before entering the
character.
Unit = Measurement unit.
Hold = Display holding parameter.
Selecting NonE , this parameter becomes
inactive.
Selecting Lo. , always the minimum
measured value is displayed.
Selecting Hi. , always the maximum
Measurement is performed at each 200ms.
However,
for FASt rate, each measurement is displayed.
for SLo.1 rate, the average of 4 successive
measurements is displayed.
for SLo.2 rate, the average of 8 successive
measurements is displayed.
for SLo.3 rate, the average of 16 successive
measurements is displayed.
See NOTE 1 for programming.
NOTE 1
Unit
Hold
rate
dsp.C.
RAtE = Sampling rate.
dSP.C. = Display configuration.
Selectable as PrcS. or Pr.Un. . If PrcS. is
selected, process value appears. If Pr.Un.
is selected, process value and then
measurement unit are displayed 4 and 2
seconds successively.
See NOTE 1 for programming.
i.typ.
No
Measurement unit
If
key is pressed and held for 5
seconds programming mode is entered
SET
Measurement
value
SET
If first
and then
keys are
pressed together , measurement
unit appears. See Unit
parameter
For programming.
i.typ. = Input type.
Input type can be selected as 0-20mA,
4-20mA, 0-1V or 0-10V.
See NOTE 1 for programming.
d.Cnf.
SET
1000
SET
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement