MD65 AC Drive User Manual Version 1.0

MD65 AC Drive User Manual Version 1.0
MD65 AC Drive
User Manual
Version 1.0
Instruction Manual D2-3519-1
The information in this manual is subject to change without notice.
Throughout this manual, the following notes are used to alert you to safety
considerations:
!
ATTENTION: Identifies information about practices or
circumstances that can lead to personal injury or death,
property damage, or economic loss.
Important: Identifies information that is critical for successful application and
understanding of the product.
The thick black bar shown on the outside margin of this page is used throughout this
manual to signify new or revised text or figures.
!
ATTENTION: Only qualified personnel familiar with the
construction and operation of this equipment and the hazards
involved should install, adjust, operate, or service this equipment.
Read and understand this document in its entirety before
proceeding. Failure to observe this precaution could result in
severe bodily injury or loss of life.
ATTENTION: The drive contains high voltage capacitors that take
time to discharge after removal of mains supply. Before working
on the drive, ensure isolation of mains supply from line inputs [R,
S, T (L1, L2, L3)]. Wait three (3) minutes for capacitors to
discharge to safe voltage levels. Darkened display LEDs is not an
indication that capacitors have discharged to safe voltage levels.
Failure to observe this precaution could result in severe bodily
injury or loss of life.
ATTENTION: The drive can operate at and maintain zero speed.
The user is responsible for assuring safe conditions for operating
personnel by providing suitable guards, audible or visual alarms,
or other devices to indicate that the drive is operating, or may
operate, at or near zero speed. Failure to observe this precaution
could result in severe bodily injury or loss of life.
ATTENTION: The drive contains ESD- (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are
required when installing, testing, servicing, or repairing the drive.
Erratic machine operation and damage to, or destruction of,
equipment can result if this precaution is not followed. Failure to
observe this precaution can result in bodily injury.
ATTENTION: The user must provide an external, hardwired
emergency stop circuit outside of the drive circuitry. This circuitry
must disable the system in case of improper operation.
Uncontrolled machine operation may result if this precaution is
not followed. Failure to observe this precaution could result in
bodily injury.
ATTENTION: The user is responsible for conforming with all
applicable local and national codes. Failure to observe this
precaution could result in damage to, or destruction of, the
equipment.
ATTENTION: An incorrectly applied or installed drive can result
in component damage or reduction in product life. Wiring or
application errors, such as undersizing the motor, incorrect or
inadequate AC supply, or excessive ambient temperatures may
result in malfunction of the system.
MD65, VS Utilities, and Reliance are trademarks of Rockwell Automation.
©2003 Rockwell Automation. All rights reserved.
CONTENTS
Chapter 1
Introduction
1.1 Getting Assistance from Reliance Electric..................... 1-1
Chapter 2
About the MD65 Drive
2.1 Identifying the Drive by Model Number.......................... 2-1
2.2 Identifying the Drive by Catalog Number ....................... 2-2
2.3 MD65 Drive Ratings, Model Numbers, Catalog
Numbers, and Frame Sizes........................................... 2-2
2.4 Kits and Accessories ..................................................... 2-4
2.5 Storage Guidelines ........................................................ 2-5
Chapter 3
Mounting the Drive
3.1 General Requirements for the Installation Site .............. 3-1
3.1.1 Operating Conditions........................................... 3-2
3.1.2 Minimum Mounting Clearances ........................... 3-2
3.1.3 Mounting Dimensions for the MD65 Drive........... 3-3
3.2 Mounting the Drive......................................................... 3-6
3.2.1 Protecting the Drive from Debris ......................... 3-6
Chapter 4
Grounding the Drive
4.1 RFI Filter Grounding ...................................................... 4-2
Chapter 5
Installing Power Wiring
5.1 Opening the Cover......................................................... 5-1
5.2 Verifying Drive AC Input Ratings Match Available
Power ............................................................................ 5-2
5.2.1 Ungrounded Distribution Systems ....................... 5-2
5.2.2 Input Power Conditioning .................................... 5-4
5.3 Power Wiring Specifications .......................................... 5-4
5.4 Power Terminal Block Connections............................... 5-5
5.5 Fuses and Circuit Breakers ........................................... 5-6
5.6 Motor Cable Types Acceptable for 200-600 Volt
Installations ................................................................... 5-8
5.7 Reflected Wave Protection .......................................... 5-10
5.8 Output Disconnect ....................................................... 5-10
Chapter 6
Installing Control Wiring
6.1 Stop Circuit Requirements............................................. 6-1
6.2 Motor Start/Stop Precautions......................................... 6-2
6.3 I/O Wiring Recommendations........................................ 6-3
6.3.1 Maximum Control Wire Length
Recommendations ............................................. 6-3
Contents
I
6.4 Wiring the Control Terminal Block ................................. 6-4
6.4.1 I/O Wiring Examples ............................................ 6-6
6.4.2 Typical Multiple Drive Connection Examples....... 6-9
6.5 Start and Speed Reference Control............................. 6-10
6.6 Accel/Decel Selection .................................................. 6-11
Chapter 7
Completing the Installation
7.1 Checking the Installation Before Applying Power to
the Drive ........................................................................ 7-1
7.2 Powering Up After Installation is Complete.................... 7-2
Chapter 8
Using the Integral Keypad to Program and Control the Drive
8.1 Keypad Components ..................................................... 8-1
8.1.1 Display Description .............................................. 8-2
8.1.2 LED Descriptions ................................................. 8-2
8.1.3 Key Descriptions.................................................. 8-3
8.2 About Parameters .......................................................... 8-4
8.3 How Parameters are Organized .................................... 8-4
8.4 Viewing and Adjusting Basic (P) and Advanced (A)
Parameters .................................................................... 8-5
8.5 Viewing the Display (d) Parameters............................... 8-6
Chapter 9
Parameter Descriptions
9.1 Basic Program Group Parameters................................. 9-2
9.2 Advanced Group Parameters ........................................ 9-8
9.3 Display Group Parameters........................................... 9-43
Chapter 10 Troubleshooting the Drive
10.1 Fault Codes.................................................................. 10-1
10.1.1 Manually Clearing Faults ................................... 10-2
10.1.2 Automatically Clearing Faults (Auto Restart
Feature) ............................................................. 10-2
10.2 Troubleshooting Tables ............................................... 10-7
10.2.1 Problem: Drive Does Not Start From Terminal
Block Start or Run Inputs .................................. 10-7
10.2.2 Problem: Drive Does Not Start From Integral
Keypad .............................................................. 10-8
10.2.3 Problem: Drive Does Not Respond to
Changes in Speed Command ........................... 10-8
10.2.4 Problem: Motor Does Not Start.......................... 10-9
10.2.5 Problem: Motor and/or Drive Will Not
Accelerate to Commanded Speed .................. 10-10
10.2.6 Problem: Motor Operation is Unstable............. 10-10
10.2.7 Problem: Drive Will Not Reverse Motor
Direction. ......................................................... 10-11
10.2.8 Problem: Drive Does Not Power Up ................ 10-11
II
MD65 AC Drive User Manual
Appendix A Technical Specifications........................................................A-1
Appendix B Record of User Settings ........................................................B-1
Appendix C Parameters Cross-Referenced by Name ..............................C-1
Appendix D CE Conformance Requirements ..........................................D-1
Appendix E Accessories ..........................................................................E-1
Appendix F RS485 (MDI) Protocol .......................................................... F-1
Appendix G RJ45 Splitter Cable .............................................................. G-1
Index
Contents
....................................................................................... Index-1
III
IV
MD65 AC Drive User Manual
List of Figures
Figure 2.1 – Identifying the Drive by Model Number................................... 2-1
Figure 2.2 – Identifying the Drive by Catalog Number ................................ 2-2
Figure 3.1 – Minimum Mounting Clearances .............................................. 3-2
Figure 3.2 – Drive Dimensions and Weights............................................... 3-3
Figure 3.3 – Drive Dimensions - NEMA 1/IP30 Kit Without
Communication Option ........................................................... 3-4
Figure 3.4 – Drive Dimensions - NEMA 1/IP30 Kit With Communication
Option ..................................................................................... 3-5
Figure 4.1 – Typical Grounding................................................................... 4-1
Figure 5.1 – Opening the Cover.................................................................. 5-1
Figure 5.2 – Removing the Finger Guard ................................................... 5-2
Figure 5.3 – Removing the Jumper............................................................. 5-3
Figure 5.4 – Phase-to-Ground MOV Removal............................................ 5-3
Figure 5.5 – Power Terminal Block Connections........................................ 5-5
Figure 6.1 – Control Terminal Block ........................................................... 6-4
Figure 6.2 – Override Priority for the Speed Reference Command .......... 6-10
Figure 6.3 – Accel/Decel Selection ........................................................... 6-11
Figure 8.1 – Integral Keypad ...................................................................... 8-1
Figure 9.1 – Accel Time 1 (P039) ............................................................... 9-6
Figure 9.2 – Decel Time 1 (P040)............................................................... 9-6
Figure 9.3 – Accel Time 2 (A067) ............................................................. 9-18
Figure 9.4 – Decel Time 2 (A068)............................................................. 9-18
Figure 9.5 – DC Brake Level (A081)......................................................... 9-21
Figure 9.6 – S Curve % (A083) Example.................................................. 9-22
Figure 9.7 – Boost Select (A084).............................................................. 9-23
Figure 9.8 – Start Boost (A085) ................................................................ 9-24
Figure 9.9 – Motor OL Select (A090) ........................................................ 9-25
Figure 9.10 – Derating Guidelines Based on PWM Frequency (A091)
Selection ............................................................................. 9-26
Figure 9.11 – Anlg In 0-10V Lo (A110) ..................................................... 9-32
Figure 9.12 – Skip Freq Band (A120) ....................................................... 9-34
Figure 9.13 – Digit Settings....................................................................... 9-42
Figure 9.14 – Drive Status (d006) Bit Definitions...................................... 9-44
Figure 9.15 – Control Source (d012) Bit Definitions ................................. 9-45
Figure 9.16 – Contrl In Status (d013) Bit Definitions................................. 9-46
Figure 9.17 – Dig In Status (d014) Bit Definitions..................................... 9-46
Figure 9.18 – Comm Status (d015) Bit Definitions.................................... 9-47
Contents
V
VI
MD65 AC Drive User Manual
List of Tables
Table 2.1 – Drive Ratings, Model Numbers, Catalog Numbers, and
Frame Sizes............................................................................. 2-2
Table 2.2 – Standard Kits and Accessories ................................................ 2-4
Table 3.1 – Ambient Operating Temperatures and Mounting
Clearances ............................................................................... 3-2
Table 3.2 – Mounting Specifications ........................................................... 3-6
Table 5.1 – Corrective Actions for Input Power Conditions ........................ 5-4
Table 5.2 – Power Wiring Specifications .................................................... 5-4
Table 5.3 – Power Terminal Block Specifications....................................... 5-5
Table 5.4 – Drive, Fuse, and Circuit Breaker Ratings................................. 5-7
Table 5.5 – Shielded Motor Cable Types Acceptable for 200-600 Volt
Installations.............................................................................. 5-9
Table 5.6 – Maximum Cable Length Recommendation............................ 5-10
Table 6.1 – Recommended Control and Signal Wire.................................. 6-3
Table 6.2 – I/O Terminal Block Specifications ............................................ 6-3
Table 6.3 – Control Terminal Definitions and Related Parameters............. 6-5
Table 6.4 – Typical Multiple Drive Connection Examples........................... 6-9
Table 8.1 – LED Descriptions ..................................................................... 8-2
Table 8.2 – Key Descriptions ...................................................................... 8-3
Table 8.3 – Viewing and Adjusting Basic (P) and Advanced (A)
Parameters .............................................................................. 8-5
Table 8.4 – Viewing the Display (d) Parameters......................................... 8-6
Table 9.1 – Trip Points for Digital Output Relay........................................ 9-13
Table 9.2 – On/Off Points for the Opto Outputs........................................ 9-16
Table 9.3 – A064 Options ......................................................................... 9-16
Table 9.4 – Analog Output Signal Mode Selections ................................. 9-17
Table 9.5 – Selecting the Reference Source Using Presets..................... 9-20
Table 9.6 – Related Parameters for Stp Logic Parameters
(A140-A147) .......................................................................... 9-40
Table 10.1 – Fault Descriptions and Corrective Actions ........................... 10-3
Table 10.2 – Problem: Drive Does Not Start From Terminal Block
Start or Run Inputs............................................................... 10-7
Table 10.3 – Problem: Drive Does Not Start From Integral Keypad ......... 10-8
Table 10.4 – Problem: Drive Does Not Respond to Changes in
Speed Command ................................................................. 10-8
Table 10.5 – Problem: Motor and/or Drive Will Not Accelerate to
Commanded Speed ........................................................... 10-10
Table 10.6 – Problem: Motor Operation is Unstable............................... 10-10
Table 10.7 – Problem: Drive Will Not Reverse Motor Direction .............. 10-11
Contents
VII
VIII
MD65 AC Drive User Manual
CHAPTER 1
Introduction
This manual is intended for qualified electrical personnel familiar
with installing, programming, and maintaining AC drives.
This manual contains information on:
•
•
•
Installing and wiring the MD65 drive
Programming the drive
Troubleshooting the drive
The latest version of this manual is available from
http://www.theautomationbookstore.com or
http://www.reliance.com/docs_onl/online_stdrv.htm.
1.1
Getting Assistance from Reliance
Electric
If you have any questions or problems with the products described
in this instruction manual, contact your local Reliance Electric sales
office.
For technical assistance, call 1-800-726-8112. Before calling,
please review the troubleshooting section of this manual and check
the Reliance Standard Drives website for additional information.
When you call this number, you will be asked for the drive model
number or catalog number and this instruction manual number.
Introduction
1-1
1-2
MD65 AC Drive User Manual
CHAPTER 2
About the MD65 Drive
This chapter provides general information about the MD65 AC
drive, including how to identify the drive.
2.1
Identifying the Drive by Model
Number
Each drive can be identified by its model number, as shown in
figure 2.1. The model number is on the shipping label and the drive
nameplate. The model number includes the drive and any options.
Drive model numbers are provided in table 2.1.
6MD V N - 2P3 1 0 2
6MD = Product Family
A = 1-Phase, 240 VAC
V = 1-Phase, 120 VAC
B = 3-Phase, 240 VAC
D = 3-Phase, 460VAC
N = IP20 (Open)
1 = MD60 Drive
2 = MD65 Drive
0 = No Filter
1 = Internal Filter
Reserved
@115V / 230 VAC
2P3 = 2.3 A, 0.5 HP
5P0 = 5.0 A, 1 HP
6P0 = 6.0 A, 1.5 HP
8P0 = 8 A, 2 HP
012 = 12 A, 3 HP
017 = 17.5 A, 5 HP
024 = 24 A, 7.5 HP
033 = 33 A, 10 HP
@460 VAC
1P4 = 1.4 A, 0.5 HP
2P3 = 2.3 A, 1 HP
4P0 = 4 A, 2 HP
6P0 = 6 A, 3 HP
010 = 10.5 A, 5 HP
012 = 12 A, 7.5 HP
017 = 17 A, 10 HP
Figure 2.1 – Identifying the Drive by Model Number
About the MD65 Drive
2-1
2.2
Identifying the Drive by Catalog
Number
In addition to the model number, MD65 drives can be identified and
ordered using a catalog number. The catalog number is on the
nameplate. See figure 2.2.
6MB 4 0 005
HP (005 = 5 HP)
Enclosure (0 = IP20)
Volts (4 = 460)
Product (MB = MD65 Drive)
Figure 2.2 – Identifying the Drive by Catalog Number
2.3
MD65 Drive Ratings, Model Numbers,
Catalog Numbers, and Frame Sizes
Similar MD65 drive sizes are grouped into frame sizes to simplify
re-ordering and dimensioning. Refer to figures 3.2 through 3.4 for
the dimensions of each frame size.
Table 2.1 provides MD65 drive ratings, model numbers, catalog
numbers, and frame sizes.
Table 2.1 – Drive Ratings, Model Numbers, Catalog Numbers, and Frame
Sizes
Drive Ratings
Input Voltage
120V 50/60 Hz
1-Phase
No Filter
240V 50/60 Hz
1-Phase
With Integral
“S Type” EMC Filter
2-2
kW
0.4
HP
0.5
Output
Current
2.3A
0.75
1.0
5.0A
1.1
1.5
6.0A
0.4
0.5
2.3A
0.75
1.0
5.0A
1.5
2.0
8.0A
2.2
3.0
12.0A
Model Number
(Catalog Number)
6MDVN-2P3102
(6MB100P5)
6MDVN-5P0102
(6MB10001)
6MDVN-6P0102
(6MB101P5)
6MDAN-2P3112
(N/A)
6MDAN-5P0112
(N/A)
6MDAN-8P0112
(N/A)
6MDAN-012112
(N/A)
Frame
Size
B
B
B
B
B
B
C
MD65 AC Drive User Manual
Table 2.1 – Drive Ratings, Model Numbers, Catalog Numbers, and Frame
Sizes (Continued)
Drive Ratings
Input Voltage
240V 50/60 Hz
1-Phase
No Filter
240V 50/60 Hz
3-Phase
No Filter
480V 50/60 Hz
3-Phase
No Filter
About the MD65 Drive
kW
0.4
HP
0.5
Output
Current
2.3 A
0.75
1.0
5.0 A
1.5
2.0
8.0 A
2.2
3.0
12.0 A
0.4
0.5
2.3 A
0.75
1.0
5.0 A
1.5
2.0
8.0 A
2.2
3.0
12.0 A
3.7
5.0
17.5 A
5.5
7.5
24.0 A
7.5
10.0
33.0 A
0.4
0.5
1.4 A
0.75
1.0
2.3 A
1.5
2.0
4.0 A
2.2
3.0
6.0 A
4.0
5.0
10.5 A
5.5
7.5
12.0 A
7.5
10.0
17.0 A
Model Number
(Catalog Number)
6MDAN-2P3102
(6MB300P5)
6MDAN-5P0102
(6MB30001)
6MDAN-8P0102
(6MB30002)
6MDAN-012102
(6MB30003)
6MDBN-2P3102
(6MB200P5)
6MDBN-5P0102
(6MB20001)
6MDBN-8P0102
(6MB20002)
6MDBN-012102
(6MB20003)
6MDBN-017102
(6MB20005)
6MDBN-024102
(6MB20007)
6MDBN-033102
(6MB20010)
6MDDN-1P4102
(6MB400P5)
6MDDN-2P3102
(6MB40001)
6MDDN-4P0102
(6MB40002)
6MDDN-6P0102
(6MB40003)
6MDDN-010102
(6MB40005)
6MDDN-012102
(6MB40007)
6MDDN-017102
(6MB40010)
Frame
Size
B
B
B
C
B
B
B
B
B
C
C
B
B
B
B
B
C
C
2-3
2.4
Kits and Accessories
Table 2.2 lists kits and accessories for the MD65 drive. Contact
Reliance Electric for more information about these kits.
Table 2.2 – Standard Kits and Accessories
Kit Description
DeviceNet Communication Module (requires a
Communication Module Cover, purchased
separately)
Model Number
MDCOMM-DNET
Communication Module Cover, B-Frame Drive 6MD-COMMCVR-B
Communication Module Cover, C-Frame Drive 6MD-COMMCVR-C
Serial Converter Module (RS485 to RS232;
includes VS Utilities software and cable)
RECOMM-232
VS Utilities Software CD
RECOMM-VSUTIL
NEMA 1/IP30 Kit, B-Frame drive (includes
conduit box with mounting screws and plastic
top panel)
6MD-NM1B
NEMA 1/IP30 Kit, C-Frame drive (includes
conduit box with mounting screws and plastic
top panel)
6MD-NM1C
NEMA 1/IP30 Kit for Communication Option,
B-Frame Drive (includes communication
option conduit box with mounting screws and
plastic top panel)
6MD-NM1COMMB
NEMA 1/IP30 Kit for Communication Option,
C-Frame Drive (includes communication
option conduit box with mounting screws and
plastic top panel)
6MD-NM1COMMC
Remote Panel-Mount OIM (digital speed
control, CopyCat capable, IP66 (NEMA 4X/12
indoor use only), includes 2.9 meter cable).
MD4LCD-PNL
Remote Handheld OIM (digital speed control,
full numeric keypad, CopyCat capable, IP30
(NEMA Type 1); includes 1.0 meter cable;
panel-mount with optional Bezel Kit.
MD1CC
Bezel Kit (panel mount for Remote Handheld
OIM)
MDBZL-N1
OIM Cable (1.0 meter OIM-to-RJ45 cable)
MDCBL-CC1
OIM Cable (2.9 meter OIM-to-RJ45 cable)
MDCBL-CC3
RJ45 Cable (2.0 meter RJ45-to-RJ45 cable,
male-to-male connectors)
MDCBL-RJ45
2-4
MD65 AC Drive User Manual
Table 2.2 – Standard Kits and Accessories (Continued)
Kit Description
Model Number
Serial Cable (2.0 meter serial cable with a
locking low profile connector to connect to the
serial converter and a 9-pin sub-miniature D
female connector to connect to a computer)
RECBL-SFC
Dynamic Brake Resistors
AK-R2-xxx
RJ45 Splitter Cable (RJ45 one-to-two port
splitter cable)
AK-U0-RJ45-SCI
Terminating Resistors (RJ45 120 Ohm
resistors; 2 pieces)
AK-U0-RJ45-TRI
Terminal Block (RJ45 two-position terminal
block; 5 pieces)
AK-U0-TB2P
2.5
Storage Guidelines
If you need to store the drive, follow these recommendations to
prolong drive life and performance:
•
Store the drive within an ambient temperature range of -40° to
+85° C.
•
Store the drive within a relative humidity range of 0% to 95%,
non-condensing.
•
Do not expose the drive to a corrosive atmosphere.
About the MD65 Drive
2-5
2-6
MD65 AC Drive User Manual
CHAPTER 3
Mounting the Drive
This chapter provides information that must be considered when
planning an MD65 drive installation and provides drive mounting
information and installation site requirements.
!
ATTENTION: Only qualified electrical personnel familiar with
the construction and operation of this equipment and the
hazards involved should install, adjust, operate, or service this
equipment. Read and understand this manual and other
applicable manuals in their entirety before proceeding. Failure
to observe this precaution could result in severe bodily injury
or loss of life.
ATTENTION: Use of power correction capacitors on the
output of the drive can result in erratic operation of the motor,
nuisance tripping, and/or permanent damage to the drive.
Remove power correction capacitors before proceeding.
Failure to observe this precaution could result in damage to,
or destruction of, the equipment.
ATTENTION: The user is responsible for conforming with all
applicable local, national, and international codes. Failure to
observe this precaution could result in damage to, or
destruction of, the equipment.
3.1
General Requirements for the
Installation Site
It is important to properly plan before installing an MD65 drive to
ensure that the drive’s environment and operating conditions are
satisfactory.
The area behind the drive must be kept clear of all control and
power wiring. Power connections may create electromagnetic fields
that may interfere with control wiring or components when run in
close proximity to the drive.
Read the recommendations in the following sections before
continuing with the drive installation.
Mounting the Drive
3-1
3.1.1 Operating Conditions
Before deciding on an installation site, consider the following
guidelines:
•
•
•
•
Protect the cooling fan by avoiding dust or metallic particles.
Do not expose the drive to a corrosive atmosphere.
Protect the drive from moisture and direct sunlight.
Verify that the drive location will meet the environmental
conditions specified in table 3.1.
Table 3.1 – Ambient Operating Temperatures and Mounting Clearances
Ambient
Temperature
Minimum Maximum
-10°C
(14°F)
40°C
(104°F)
Enclosure
Rating
IP20/Open Type
Minimum Mounting
Clearances
Use Mounting Option A
(figure 3.1)
IP30/NEMA 1/UL Use Mounting Option B
(figure 3.1)
Type 11
50°C
(122°F)
1
IP20/Open Type
Use Mounting Option B
(figure 3.1)
Rating requires installation of the MD65 NEMA 1/IP30 Kit.
3.1.2 Minimum Mounting Clearances
Refer to figure 3.1 for the minimum mounting clearances. Refer to
section 3.1.3 for drive mounting dimensions.
25 mm
(1.0 in)
120 mm
(4.7 in)
120 mm
(4.7 in)
Mounting Option A
No clearance required
between drives
Mounting Option B
120 mm
(4.7 in)
120 mm
(4.7 in)
See figure 3.2 for drive dimensions.
Figure 3.1 – Minimum Mounting Clearances
3-2
MD65 AC Drive User Manual
3.1.3 Mounting Dimensions for the MD65 Drive
Overall dimensions and weights are illustrated in figures 3.2, 3.3,
and 3.4 as an aid to calculating the total area required by the MD65
drive. Dimensions are in millimeters and (inches). Weights are in
kilograms and (pounds). See table 2.1 for drive ratings by frame.
A
C
D
F
E
B
5.5 (0.22)
Side
Front
Frame
A
B
C
D
E
F
B
100 (3.94) 180 (7.09) 136 (5.35) 87 (3.43) 168 (6.61) 87.4 (3.44)
C
130 (5.1) 260 (10.2) 180 (7.1) 116 (4.57) 246 (9.7)
1
Shipping
Weight
2.2 (4.9)
4.3 (9.5)
Figure 3.2 – Drive Dimensions and Weights
1
C Frame does not have DIN rail mounting.
Mounting the Drive
3-3
79.1 (3.11)
64.1 (2.52)
40.6 (1.60)
25.6 (1.01)
∅ 22.2
(0.87)
213
(8.39)
109.9
(4.33)
74.3
(2.93)
33.0
(1.30)
Side View
Bottom View
Frame B
∅ 28.5
(1.12)
107.0 (4.21)
66.0 (2.60)
24.0 (0.94)
∅ 22.2
(0.87)
320
(12.56)
152.2
(5.99)
111.2
(4.38)
60.0
(2.36)
Side View
Bottom View
Frame C
All dimensions are in mm (in).
Figure 3.3 – Drive Dimensions - NEMA 1/IP30 Kit Without Communication Option
3-4
MD65 AC Drive User Manual
25.0
(0.98)
77.5 (3.05)
50.0 (1.97)
22.5 (0.89)
∅ 22.2
(0.87)
244
(9.61)
134.3
(5.29)
105.3
(4.15)
76.3
(3.00)
64.0
(2.52)
Side View
Bottom VIew
Frame B
25.0
(0.98)
108.7 (4.28)
92.2 (3.63)
69.2 (2.72)
45.7 (1.80)
∅ 28.5
(1.12)
22.2 (0.87)
∅ 22.2
(0.87)
320
(12.56)
179.8
(7.08)
144.8
(5.70)
109.8
(4.32)
60.0
(2.36)
Side View
Bottom VIew
Frame C
Dimensions shown in mm (in).
Figure 3.4 – Drive Dimensions - NEMA 1/IP30 Kit With Communication Option
Mounting the Drive
3-5
3.2
Mounting the Drive
Mount the drive upright on a flat, vertical, and level surface.
Table 3.2 – Mounting Specifications
Frame
Screw Size
Screw Torque
-OR-
DIN Rail
B
M4 (#8-32)
1.56-1.96 N-m (14-17 in-lb)
35 mm
C
M5 (#10-24)
2.45-2.94 N-m (22-26 in-lb)
–
3.2.1 Protecting the Drive from Debris
A plastic top panel is included with the drive. Install the panel to
prevent debris from falling through the vent of the drive housing
during installation. Remove the panel for IP20/Open Type
applications.
3-6
MD65 AC Drive User Manual
CHAPTER 4
Grounding the Drive
!
ATTENTION: The following information is merely a
guide for proper installation. Rockwell Automation
cannot assume responsibility for the compliance or
the noncompliance to any code, national, local or
otherwise for the proper installation of this drive or
associated equipment. A hazard of personal injury
and/or equipment damage exists if codes are
ignored during installation.
The drive Safety Ground (PE) must be connected to system
ground. Ground impedance must conform to the requirements of
national and local industrial safety regulations and/or electrical
codes. The integrity of all ground connections should be periodically
checked.
R/L1
S/L2
T/L3
U/T1
V/T2
W/T3
SHLD
Figure 4.1 – Typical Grounding
Ground Fault Monitoring
If a system ground fault monitor is to be used, only Type B
(adjustable) devices should be used to avoid nuisance tripping.
Grounding the Drive
4-1
Safety Ground -
(PE)
This is the safety ground for the drive that is required by code. One
of these points must be connected to adjacent building steel (girder,
joist), a floor ground rod, or bus bar. Grounding points must comply
with national and local industrial safety regulations and/or electrical
codes.
Motor Ground
The motor ground must be connected to one of the ground
terminals on the drive.
Shield Termination - SHLD
Either of the safety ground terminals located on the power terminal
block provides a grounding point for the motor cable shield. The
motor cable shield connected to one of these terminals (drive end)
should also be connected to the motor frame (motor end). Use a
shield terminating or EMI clamp to connect the shield to the safety
ground terminal. The NEMA 1/IP30 Kit may be used with a cable
clamp for a grounding point for the cable shield.
When shielded cable is used for control and signal wiring, the
shield should be grounded at the source end only, not at the drive
end.
4.1
RFI Filter Grounding
Using single-phase drives with integral filter, or an external filter with
any drive rating, may result in relatively high ground leakage
currents. Therefore, the filter must only be used in installations
with grounded AC supply systems and be permanently
installed and solidly grounded (bonded) to the building power
distribution ground.
Ensure that the incoming supply neutral is solidly connected
(bonded) to the same building power distribution ground. Grounding
must not rely on flexible cables and should not include any form of
plug or socket that would permit inadvertent disconnection. Some
local codes may require redundant ground connections. The
integrity of all connections should be periodically checked.
4-2
MD65 AC Drive User Manual
CHAPTER 5
Installing Power Wiring
ATTENTION: The user is responsible for conforming
with all applicable local and national codes. Failure
to observe this precaution could result in damage to,
or destruction of, the equipment.
!
ATTENTION: To avoid a possible shock hazard
caused by induced voltages, unused wires in the
conduit must be grounded at both ends. For the
same reason, if a drive sharing a conduit is being
serviced or installed, all drives using this conduit
should be disabled. This will help minimize the
possible shock hazard from “cross-coupled” power
leads.
This chapter provides instructions on wiring output wiring to the
motor and installing AC input power wiring.
5.1
Opening the Cover
To access the power terminal block:
Step 1.
Open the cover.
a. Press and hold in the tabs on each side of the cover.
b. Pull the cover out and up to release (refer to figure
5.1).
Figure 5.1 – Opening the Cover
Installing Power Wiring
5-1
Step 2.
Remove the finger guard (refer to figure 5.2).
a. Press in and hold the locking tab.
b. Slide finger guard down and out.
Replace the finger guard and cover when wiring is complete.
Figure 5.2 – Removing the Finger Guard
5.2
Verifying Drive AC Input Ratings
Match Available Power
It is important to verity that plant power meets the input power
requirements of the drive’s circuitry. Refer to table 5.4 for input
power rating specifications. Be sure input power to the drive
corresponds to the drive nameplate voltage and frequency.
5.2.1 Ungrounded Distribution Systems
!
ATTENTION: MD65 drives contain protective MOVs
that are referenced to ground. These devices should
be disconnected if the drive is installed on an
ungrounded distribution system.
To prevent drive damage, the MOVs connected to ground should be
disconnected if the drive is installed on an ungrounded distribution
system where the line-to-ground voltages on any phase could
exceed 125% of the nominal line-to-line voltage.
5-2
MD65 AC Drive User Manual
Disconnecting MOVs
To disconnect MOVs, you must remove the external jumper located
on the lower left side of the front of the drive.
To remove the jumper, use the following procedure and refer to
figures 5.3 and 5.4.
Step 1.
Open the cover.
Step 2.
Locate the screw below and to the left of the power
terminal block.
Step 3.
Turn the screw counterclockwise to loosen. Do not
remove screw.
Step 4.
Pull the jumper completely out of the drive chassis.
Step 5.
Tighten the screw to keep it in place.
Important: Tighten screw after
jumper removal.
Jumper
Figure 5.3 – Removing the Jumper
R/L1
Three-Phase
AC Input S/L2
T/L3
Jumper
1
2
3
4
Figure 5.4 – Phase-to-Ground MOV Removal
Installing Power Wiring
5-3
5.2.2 Input Power Conditioning
The drive is suitable for direct connection to input power within the
rated voltage of the drive (see table 5.4). Table 5.1 lists certain input
power conditions that may cause component damage or reduction
in product life. If any of the conditions exist, install one of the
devices listed in the “Corrective Action” column in table 5.1 on the
line side of the drive.
Important:
Only one device per branch circuit is required. It
should be mounted closest to the branch and sized to
handle the total current of the branch circuit.
Table 5.1 – Corrective Actions for Input Power Conditions
Input Power Condition
Corrective Action
Low line impedance (less than 1% line
reactance)
Install one of the following:
Line reactor1
•
•
Greater than 120 kVA supply transformer
Isolation transformer
Line has power factor correction capacitors
Line has frequent power interruptions
Line has intermittent noise spikes in excess of
6000V (lightning)
Phase-to-ground voltage exceeds 125% of
normal line-to-line voltage
Ungrounded distribution system
1
•
Remove MOV jumper to
ground and install
isolation transformer
with grounded
secondary, if necessary.
Contact Reliance Electric for application and ordering information.
5.3
Power Wiring Specifications
Table 5.2 – Power Wiring Specifications
Power Wiring Rating
Recommended Copper Wire
Unshielded 600 V, 75° C (167° F) THHN/ 15 mils insulated, dry location
THWN
Shielded 600 V, 90° C (194° F)
RHH/RHW-2
Belden 29501-29507 or
equivalent
Shielded Tray rated 600 V, 90° C (194° F) Shawflex 2ACD/3ACD or
RHH/RHW-2
equivalent
5-4
MD65 AC Drive User Manual
5.4
Power Terminal Block Connections
Table 5.3 – Power Terminal Block Specifications
Frame Maximum Wire Size 1
1
Minimum Wire Size 1
Torque
B
5.3 mm (10 AWG)
1.3
(16 AWG)
1.7-2.2 Nm
(16-19 in-lb)
C
8.4 mm2 (8 AWG)
1.3 mm2 (16 AWG)
2.9-3.7 Nm
(26-33 in-lb)
2
mm2
Maximum/minimum sizes that the terminal block will accept. These are not
recommendations.
B Frame
C Frame
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
DC- DC+ BR+ BR-
Terminal
R/L1, S/L2
R/L1, S/L2, T/L3
U/T1
V/T2
W/T3
P2, P1
DC+, DCBR+, BR-
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
P2
P1
DC- DC+ BR+ BR-
Description
1-Phase Input
3-Phase Input
To Motor U/T1
Switch any two motor
leads to change
=
To Motor V/T2
forward direction.
To Motor W/T3
DC Bus Inductor Connection (C Frame drives only.)
The C Frame drive is shipped with a jumper between
Terminals P2 and P1. Remove this jumper only when a DC
Bus Inductor will be connected. Drive will not power up without a jumper
or inductor connected.
DC Bus Connection
Dynamic Brake Resistor Connection
[0.75 kW (1 HP) ratings and higher)
Safety Ground - PE
Figure 5.5 – Power Terminal Block Connections
Important:
Installing Power Wiring
Terminal screws may become loose during shipment.
Ensure that all terminal screws are tightened to the
recommended torque before applying power to the
drive.
5-5
5.5
Fuses and Circuit Breakers
The MD65 drive does not provide branch short circuit protection.
This product should be installed with either input fuses or an input
circuit breaker. National and local industrial safety regulations and/
or electrical codes may determine additional requirements for these
installations.
!
ATTENTION: To guard against personal injury and/
or equipment damage caused by improper fusing or
circuit breaker selection, use only the recommended
line fuses/circuit breakers specified in table 5.4.
Fuses
The MD65 drive has been UL tested and approved for use with
input fuses. The ratings in table 5.4 are the minimum recommended
values for use with each drive rating. The devices listed in this table
are provided to serve as a guide. Other devices that meet the
requirements of UL508C and UL489 with similar trip characteristics
may be used in order to meet local or national electrical codes.
If fuses are chosen as the desired protection method, refer to
the recommended types listed below. If available amp ratings do not
match the tables provided, the closest fuse rating that exceeds the
drive rating should be chosen.
•
IEC – BS88 (British Standard) Parts 1 & 2 1.
•
UL – UL Class CC, T or J must be used. 2
Circuit Breakers
The circuit breaker ratings in table 5.4 are for the highest rated
devices that supply drive protection.
1
Typical designations include, but may not be limited to the following:
Parts 1 & 2: AC, AD, BC, BD, CD, DD, ED, EFS, EF, FF, FG, GF, GG, GH.
2
Typical designations include:
Type CC - KTK-R, FNQ-R
Type J - JKS, LPJ
Type T - JJS, JJN
5-6
MD65 AC Drive User Manual
Table 5.4 – Drive, Fuse, and Circuit Breaker Ratings
Drive Ratings
Output Ratings
Model
Number
Catalog
Number
kW (HP) Amps
Branch Circuit Power
Protection Dissipation
Input Ratings
Voltage
Range
kVA Amps Fuses2
Circuit
IP20 Open
Breaker
3
Watts
100 - 120V AC 1-Phase Input, 0 - 230V 3-Phase Output
6MDVN-2P3102
6MB100P5 0.4 (0.5)
2.3
90-126
1.15
9.0
15
15
30
6MDVN-5P0102
6MB10001 0.75 (1.0)
5.0
90-126
2.45
20.3
35
30
56
6MDVN-6P0102
6MB101P5 1.1 (1.5)
6.0
90-126
3.0
24.0
40
35
70
30
200 - 240V AC – 1-Phase1 Input, 0 - 230V 3-Phase Output
6MDAN-2P3102
6MB300P5 0.4 (0.5)
2.3
180-265
1.15
6.0
10
15
6MDAN-5P0102
6MB30001 0.75 (1.0)
5.0
180-265
2.45
12.0
20
20
55
6MDAN-8P0102
6MB30002
1.5 (2.0)
8.0
180-265
4.0
18.0
30
30
80
6MDAN-012102
6MB30003
2.2 (3.0)
12.0
180-265
5.5
25.0
40
35
110
30
200 - 240V AC – 3-Phase Input, 0 - 230V 3-Phase Output
6MDBN-2P3102
6MB200P5 0.4 (0.5)
2.3
180-265
1.15
2.5
6
10
6MDBN-5P0102
6MB20001 0.75 (1.0)
5.0
180-265
2.45
5.7
10
15
55
6MDBN-8P0102
6MB20002
1.5 (2.0)
8.0
180-265
4.0
9.5
15
15
80
6MDBN-012102
6MB20003
2.2 (3.0)
12.0
180-265
5.5
15.5
25
25
115
6MDBN-017102
6MB20005
3.7 (5.0)
17.5
180-265
8.6
21.0
35
30
165
6MDBN-024102
6MB20007
5.5 (7.5)
24.0
180-265
11.8
26.1
40
40
226
6MDBN-033102
6MB20010 7.5 (10.0)
33.0
180-265
16.3
34.6
60
60
290
380 - 480V AC – 3-Phase Input, 0 - 460V 3-Phase Output
6MDDN-1P4102
6MB400P5 0.4 (0.5)
1.4
340-528
1.4
1.8
3
10
30
6MDDN-2P3102
6MB40001 0.75 (1.0)
2.3
340-528
2.3
3.2
6
10
40
6MDDN-4P0102
6MB40002
1.5 (2.0)
4.0
340-528
4.0
5.7
10
15
60
6MDDN-6P0102
6MB40003
2.2 (3.0)
6.0
340-528
5.9
7.5
15
15
90
6MDDN-010102
6MB40005
4.0 (5.0)
10.5
340-528
10.3
13.0
20
25
150
6MDDN-012102
6MB40007
5.5 (7.5)
12.0
340-528
11.8
14.2
25
30
160
6MDDN-017102
6MB40010 7.5 (10.0)
17.0
340-528
16.8
18.4
30
30
200
1
200-240V AC - 1-Phase drives are also available with an integral EMC filter.
Fuse ratings are the minimuim recommended values for use with each drive rating.
Recommended fuse type: UL Class J, CC, T or Type BS88; 600 V (550 V) or
equivalent.
3 Circuit breaker ratings are the minimum recommended values for use with each
drive rating.
2
Note: For carrier frequencies above 4 kHz, see figure 9.10.
Installing Power Wiring
5-7
5.6
Motor Cable Types Acceptable for
200-600 Volt Installations
General
A variety of cable types are acceptable for drive installations. For
many installations, unshielded cable is adequate provided it can be
separated from sensitive circuits. As an approximate guide, allow a
spacing of 0.3 meters (1 foot) for every 10 meters (32.8 feet) of
length. In all cases, long parallel runs must be avoided. Do not use
cable with an insulation thickness less than 15 mils
(0.4 mm/0.015 in).
•
UL installations in 50°C ambient must use 600 V, 75°C or 90°C
wire.
•
For UL installations in 40°C ambient, 600 V, 75°C or 90°C wire is
recommended.
Unshielded
THHN, THWN or similar wire is acceptable for drive installation in
dry environments provided adequate free air space and/or conduit
fill rates limits are provided. Do not use THHN or similarly coated
wire in wet areas. Any wire chosen must have a minimum
insulation thickness of 15 mil and should not have large variations in
insulation concentricity.
Shielded/Armored Cable
Shielded cable contains all of the general benefits of multiconductor cable with the added benefit of a copper braided shield
that can contain much of the noise generated by a typical AC drive.
Strong consideration for shielded cable should be given in
installations with sensitive equipment such as weigh scales,
capacitive proximity switches, and other devices that may be
affected by electrical noise in the distribution system. Applications
with large numbers of drives in a similar location, imposed EMC
regulations, or a high degree of communications/networking are
also good candidates for shielded cable.
Shielded cable may also help reduce shaft voltage and induced
bearing currents for some applications. In addition, the increased
impedance of shielded cable may help extend the distance that the
motor can be located from the drive without the addition of motor
protective devices such as terminator networks.
Consideration should be given to all of the general specifications
dictated by the environment of the installation, including
temperature, flexibility, moisture characteristics and chemical
resistance. In addition, a braided shield should be included and be
specified by the cable manufacturer as having coverage of at least
75%. An additional foil shield can greatly improve noise
containment.
5-8
MD65 AC Drive User Manual
A good example of recommended cable is Belden 295xx (xx
determines gauge). This cable has four XLPE insulated conductors
with a 100% coverage foil and an 85% coverage copper braided
shield (with drain wire) surrounded by a PVC jacket.
Other types of shielded cable are available, but the selection of
these types may limit the allowable cable length. Particularly, some
of the newer cables twist four conductors of THHN wire and wrap
them tightly with a foil shield. This construction can greatly increase
the cable charging current required and reduce the overall drive
performance. Unless specified in the individual distance tables as
tested with the drive, these cables are not recommended and their
performance against the lead length limits supplied is not known.
Refer to table 5.5 for acceptable shielded motor cable types.
.
Table 5.5 – Shielded Motor Cable Types Acceptable for 200-600 Volt Installations
Location
Standard
(Option 1)
Standard
(Option 2)
Rating/Type
600V, 90°C (194°F)
XHHW2/RHW-2
Anixter B209500B209507
Belden 2950129507 or equivalent
Tray rated 600V,
90°C (194°F) RHH/
RHW-2
Anixter OLF-7xxxxx
or equivalent
Class I & II; Tray rated 600V,
Division I & II 90°C (194°F) RHH/
RHW-2
Anixter 7V-7xxxx-3G
or equivalent
Installing Power Wiring
Description
•
Four tinned copper conductors with
XLPE insulation
•
Copper braid/aluminum foil
combination shield land tinned
copper drain wire.
•
•
PVC jacket
•
5 mil single helical copper tape (25%
overlap min.) with three bare copper
grounds in contact with shield
•
•
PVC jacket
•
Black sunlight-resistant PVC jacket
overall
•
Three copper grounds on #10 AWG
and smaller
Three tinned copper conductors with
XLPE insulation
Three bare copper conductors with
XLPE insulation with impervious
corrugated continuously welded
aluminum armor
5-9
5.7
Reflected Wave Protection
The drive should be installed as close to the motor as possible.
Installations with long motor cables may require the addition of
external devices, such as reactors, to limit voltage reflections at the
motor (reflected wave phenomena). Contact Reliance Electric for
recommendations.
The reflected wave data applies to all frequencies 2 to16 kHz. For
240 V ratings, reflected wave effects do not need to be considered.
Table 5.6 – Maximum Cable Length Recommendation
Reflected Wave
380-480V Ratings
1
5.8
Motor Insulation Rating
Motor Cable Only1
1000 Vp-p
15 meters (49 feet)
1200 Vp-p
40 meters (131 feet)
1600 Vp-p
170 meters (558 feet)
Longer cable lengths can be achieved by installing devices on the
output of the drive. Consult factory for recommendations.
Output Disconnect
The drive is intended to be commanded by control input signals that
will start and stop the motor. A device that routinely disconnects
then reapplies output power to the motor for the purpose of starting
and stopping the motor should not be used. If it is necessary to
disconnect power to the motor with the drive outputting power, an
auxiliary contact should be used to simultaneously disable drive
control run commands.
5-10
MD65 AC Drive User Manual
CHAPTER 6
Installing Control Wiring
This chapter describes how to wire the signal and I/O terminal strip
for stop, speed feedback, and remote control signals.
To access the control terminal block, remove the drive cover (refer
to chapter 5).
Terminal block connections are detailed in figure 6.1.
6.1
Stop Circuit Requirements
!
ATTENTION: You must provide an external,
hardwired emergency stop circuit outside of the
drive circuitry. This circuit must disable the system
in case of improper operation. Uncontrolled
machine operation can result if this procedure is not
followed. Failure to observe this precaution could
result in bodily injury.
Depending upon the requirements of the application, the MD65
drive can be configured to provide either a coast-to-rest or a rampto-rest operational stop without physical separation of the power
source from the motor. A coast-to-rest stop turns off the transistor
power device drivers. A ramp-to-rest stop fires the transistor power
device drivers until the motor comes to a stop, and then turns off the
power devices.
In addition to the operational stop, you must provide a hardwired
emergency stop external to the drive. The emergency stop circuit
must contain only hardwired electromechanical components.
Operation of the emergency stop must not depend on electronic
logic (hardware or software) or on the communication of commands
over an electronic network or link.
Note that the hardwired emergency stop you install can be used at
any time to stop the drive.
Installing Control Wiring
6-1
6.2
Motor Start/Stop Precautions
!
ATTENTION: A contactor or other device that
routinely disconnects and reapplies the AC line to the
drive to start and stop the motor can cause drive
hardware damage. The drive is designed to use
control input signals that will start and stop the motor.
If used, the input device must not exceed one
operation per minute or drive damage can occur.
Failure to observe this precaution can result in
damage to, or destruction of, equipment.
ATTENTION: The drive start/stop control circuitry
includes solid-state components. If hazards due to
accidental contact with moving machinery or
unintentional flow of liquid, gas or solids exist, an
additional hardwired stop circuit may be required to
remove the AC line to the drive. When the AC line is
removed, there will be a loss of any inherent
regenerative braking effect that might be present the motor will coast to a stop. An auxiliary braking
method may be required.
Important points to remember about I/O wiring:
•
•
•
Always use copper wire.
Wire with an insulation rating of 600V or greater is recommended.
Control and signal wires should be separated from power wires
by at least 0.3 meters (1 foot).
Important:
!
6-2
I/O terminals labeled “Common” are not referenced to
the safety ground (PE) terminal and are designed to
greatly reduce common mode interference.
ATTENTION: Driving the 4-20 mA analog input from
a voltage source could cause component damage.
Verify proper configuration prior to applying input
signals.
MD65 AC Drive User Manual
6.3
I/O Wiring Recommendations
Table 6.1 – Recommended Control and Signal Wire1
Wire Type(s)
Minimum
Insulation
Rating
Description
Belden 8760/
9460 (or equiv.)
0.8 mm (18AWG), twisted pair, 100%
shield with drain.
Belden 8770
(or equiv.)
0.8 mm2 (18AWG), 3 conductor,
shielded for remote pot only.
1
2
300 V
75° C
(167° F)
If the wires are short and contained within a cabinet that has no sensitive circuits,
the use of shielded wire may not be necessary, but is always recommended.
Table 6.2 – I/O Terminal Block Specifications
Maximum Wire Size1
1.3
1
mm2
(16 AWG)
Minimum Wire Size1
2
0.13 mm (26 AWG)
Torque
0.5 to 0.8 Nm
(4.4 in-lb to 7 in-lb)
Maximum / minimum that the terminal block will accept. These are not
recommendations.
6.3.1 Maximum Control Wire Length
Recommendations
Do not exceed control wiring length of 30 meters (100 feet). Control
signal cable length is highly dependent on electrical environment
and installation practices. To improve noise immunity, the I/O
terminal block Common must be connected to ground terminal/
protective earth. If using the RS485 port, Terminal 16 should also
be connected to ground terminal/protective earth.
Installing Control Wiring
6-3
6.4
Wiring the Control Terminal Block
Enable
Jumper
(4)
01
02
03
SNK
SRC
04
05
06
07
08
09
+24V
11
+10V
12
13
14
Relay N.O.
Relay Common
Relay N.C.
R1
0-10V
R2
0/4-20mA
15
16
17
R3
30V DC
50mA
Non-inductive
0-10V
0-20mA
R1 R2 R3
Analog Output Select
18
19
Stop
Typical
SRC Wiring
(1)(4)
Start/Run FWD
Typical
SNK Wiring
(2)
Direction/Run REV
Digital Common
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Opto Common
+24V DC
+10V DC
0-10V (or ±10V) Input
Analog Common
Pot must be
1-10k ohm
2 Watt Min.
4-20mA Input
Analog Output
Common
Opto Output 1
(3)
24V
Opto Output 2
RS485 Shield
Enable
Jumper
ENBL
01 02 03 04 05 06 07 08 09
(4)
SNK
11 12 13 14 15 16 17 18 19
RS485
SRC
1
(1)
Resistive
Inductive
30V DC
3.0 A
0.5 A
125V AC
3.0 A
0.5 A
240V AC
3.0 A
0.5 A
P036 (Start Source)
Stop
I/O Terminal 01 Stop
I/O Terminal 01 is always a coast-toKeypad
Per P037
Coast
stop input except when Start Source (P036) is set
to “3-Wire Control.” In three-wire control, I/O
3-Wire
Per P037
Per P0374
Terminal 01 is controlled by Stop Mode (P037). All
2-Wire
Per P037
Coast
other stop sources are controlled by Stop Mode
RS485 Port
Per P037
Coast
(P037).
Important: The drive is shipped with a jumper installed between I/O Terminals 01 and 11. Remove this
jumper when using I/O Terminal 01 as a stop or enable input.
1Important:
2Two-wire
control shown. For three-wire control, use a momentary input
command a start.
Use a maintained input
for I/O Terminal 03 to change direction.
on I/O Terminal 02 to
3
When using an opto output with an inductive load such as a relay, install recovery diode parallel to the
relay as shown to prevent damage to the output.
4
When the ENBL enable jumper is removed, I/O Terminal 01 will always act as a hardware enable, causing
a coast to stop without software interpretation.
Figure 6.1 – Control Terminal Block
6-4
MD65 AC Drive User Manual
Table 6.3 – Control Terminal Definitions and Related Parameters
No. Signal
Default
Description
Parameter
R1
Relay N.O.
Fault
Normally open contact for output relay.
A055
R2
Relay Common
–
Common for output relay.
R3
Relay N.C.
Fault
Normally closed contact for output relay.
Analog Output Select DIP
Switch
0-10 V
Sets analog output to either voltage or current. Setting must match Analog
Out Sel (A065).
A055
Sink/Source DIP Switch
Source (SRC)
Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch setting.
Stop1, 4
Coast
The factory-installed jumper or a normally closed input
must be present for the drive to start.
02
Start/Run FWD
Not Active
03
Dir/Run REV
Not Active
04
Digital Common
–
For digital inputs. Electronically isolated with digital
inputs from analog I/O and opto outputs.
05
Digital Input 1
Preset Freq
Program with Digital In1 Sel (A051).
06
Digital Input 2
Preset Freq
Program with Digital In2 Sel (A052).
A052
07
Digital Input 3
Local
Program with Digital In3 Sel (A053).
A053
08
Digital Input 4
Jog Forward
Program with Digital In4 Sel (A054).
A054
01
P0361, 4
Command comes from the integral keypad by default. To P036, P037
disable reverse operation, see Reverse Disable (A095). P036, P037, A095
A051
09
Opto Common
-
For opto-coupled outputs. Electronically isolated with
opto outputs from analog I/O and digital inputs.
11
+24V DC
–
Referenced to Digital Common.Drive supplied power for
digital inputs. Maximum output current is 100 mA.
12
+10V DC
–
Referenced to Analog Common. Drive supplied power
for digital 0-10 V external potentiometer. Maximum
output current is 15 mA.
13
5
+/-10V In
Not Active
For external 0-10 V (unipolar) or +/-10 V (bipolar) input
P038, A051-A054,
supply (input impedance = 100 k Ohm) or potentiometer
A123, A132
wiper.
14
Analog Common
–
For 0-10 V In or 4-20 mA In. Electronically isolated with
analog inputs and outputs from digital I/O and opto
outputs.
15
5
4-20mA In
Not Active
For external 4-20 mA input supply
(input impedance = 250 Ohm).
The default analog output is 0-10 V. To convert to a
current value, change the Analog Output Select DIP
Switch to 0-20 mA. Program with Analog Out Sel (A065).
Max analog value can be scaled with Analog Out High A065, A066
(A066).
Maximum Load: 4-20 mA = 525 ohm (10.5 V)
0-10 V = 1k ohm (10 mA)
P038
P038, A051-A054,
A132
16
Analog Output
OutFreq 1-10
17
Opto Output 1
MotorRunning
Program with A058 (Opto Out1 Sel)
A058, A059, A064
18
Opto Output 2
At Frequency
Program with A061 (Opto Out2 Sel)
A061, A062, A064
Terminal should be connected to safety ground- PE
when using the RS485 communications port.
1
P036 (Start Source)
Stop
I/O Terminal 01 Stop
Important: I/O Terminal 01 is always a coast-toKeypad
Per P037
Coast
stop input except when Start Source (P036) is set
to “3-Wire Control.” In three-wire control, I/O
3-Wire
Per P037
Per P0374
Terminal 01 is controlled by Stop Mode (P037). All
2-Wire
Per P037
Coast
other stop sources are controlled by Stop Mode
(P037).
RS485 Port
Per P037
Coast
Important: The drive is shipped with a jumper installed between I/O Terminals 01 and 11. Remove this
jumper when using I/O Terminal 01 as a stop or enable input.
19
RS485 Shield
-
2
Two-wire control shown. For three-wire control, use a momentary input
on I/O Terminal 02 to
command a start.
Use a maintained input
for I/O Terminal 03 to change direction.
3
When using an opto output with an inductive load such as a relay, install recovery diode parallel to the
relay as shown to prevent damage to the output.
4
When the ENBL enable jumper is removed, I/O Terminal 01 will always act as a hardware enable, causing
a coast to stop without software interpretation.
5
0-10 V In and 4-20 mA In are distinct input channels and may be connected simultaneously. Inputs may
be used independently for speed control or jointly when operating in PID mode.
Installing Control Wiring
6-5
6.4.1 I/O Wiring Examples
Input/Output
Potentiometer
1-10k Ohm Pot.
Recommended
(2 Watt minimum)
Connection Example
P038 (Speed Reference) = 2 “0-10V Input”
Analog Input
0 to +10V, 100k ohm
impedance
4-20 mA, 100 ohm
impedance
Bipolar
P038 (Speed
Reference) = 2 “0-10V
Input” and A123 (10V
Bipolar Enbl) = 1 “BiPolar In”
12
13
14
-/+ 10V
Common
13
14
2-Wire SRC Control - Internal Supply (SRC)
Non-Reversing
11
P036 (Start Source) =
2, 3 or 4
Stop-Run
Input must be active for
the drive to run. When
input is opened, the
drive will stop as
specified by P037
(Stop Mode).
If desired, a usersupplied 24 VDC
power source can be
used. Refer to the
“External Supply
(SRC)” example.
6-6
Unipolar (Voltage)
P038 (Speed
Reference) = 2 “0-10V
Input”
+
Common
13
14
Unipolar (Current)
P038 (Speed
Reference) = 3 “4-20mA
Input”
Common
+
14
15
External Supply (SRC)
02
02
Stop-Run
04
+24V
Common
Each digital input draws 6 mA.
MD65 AC Drive User Manual
Input/Output
2-Wire SNK Control - Internal Supply (SNK)
Non-Reversing
Connection Example
02
Stop-Run
04
2-Wire SRC Control - Internal Supply (SRC)
Run FWD/Run REV
11
P036 (Start Source) =
2, 3 or 4
Stop-Run
Input must be active for
Forward
the drive to run. When
input is opened, the
Stop-Run
drive will stop as
Reverse
specified by P037
(Stop Mode).
If both Run Forward
and Run Reverse
inputs are closed at the
same time, an
undetermined state
could occur.
2-Wire SNK Control - Internal Supply (SNK)
Run FWD/Run REV
Stop-Run
Forward
External Supply (SRC)
02
03
Stop-Run
Forward
02
03
04
Stop-Run
Reverse
+24V
Common
Each digital input draws 6 mA.
02
03
04
Stop-Run
Reverse
3-Wire SRC Control - Internal Supply (SRC)
Non-Reversing
P036 (Start Source) =
Stop 11
1
A momentary input will
Start
start the drive. A stop
input to I/O Terminal 01
will stop the drive as
specified by P037
(Stop Mode).
External Supply (SRC)
Stop
01
02
Start
+24V
01
02
04
Common
Each digital input draws 6 mA.
Installing Control Wiring
6-7
Input/Output
3-Wire SNK Control - Internal Supply (SNK)
Non-Reversing
Stop
Start
3-Wire SRC Control - Internal Supply (SRC)
Reversing
P036 (Start Source) =
Stop 11
1
A momentary input will
Start
start the drive. A stop
input to I/O Terminal 01
Direction
will stop the drive as
specified by P037
(Stop Mode). I/O
Terminal 03
determines direction.
Connection Example
01
02
03
04
External Supply (SRC)
Stop
01
02
03
01
02
03
04
Start
Direction
+24V
Common
Each digital input draws 6 mA.
3-Wire SNK Control - Internal Supply (SNK)
Reversing
Stop
Start
01
02
03
04
Direction
Opto-Output (1 & 2) Opto-Output 1
A058 (Opto Out1 Sel)
determines OptoOutput 1 (I/O Terminal
17) operation.
A061 (Opto Out2 Sel)
determines OptoOutput 2 (I/O Terminal
17
18) operation.
CR
09
When using OptoOutput with an
+24V
Common
inductive load such as
Each Opto-Output is rated
a relay, install a
recovery diode parallel 30 VDC 50 mA (Non-inductive).
to the relay as shown,
to prevent damage to
the output.
6-8
MD65 AC Drive User Manual
Input/Output
Connection Example
Analog Output
A065 (Analog Out Sel) = 0 through 14
A065 (Analog Out Sel) The Analog Output Select DIP Switch must be set to match the analog output
determines analog
signal mode set in A065 (Analog Out Sel).
output type and drive
conditions.
0-10V,
1k ohm minimum
14
Common
0-20mA/4-20mA,
525 ohm maximum
16
+
6.4.2 Typical Multiple Drive Connection Examples
Table 6.4 – Typical Multiple Drive Connection Examples
Input
Multiple Digital
Input
Connections
Connection Example
02
04
Customer Inputs
02
04
02
04
Optional Ground Connection
When connecting a single input such as Run, Stop, Reverse or Preset
Speeds to multiple drives, it is important to connect I/O Terminal 04
common together for all drives. If they are to be tied into another common
(such as earth ground or separate apparatus ground) only one point of
the daisy chain of I/O Terminal 04 should be connected.
Multiple Analog
Connections
12 13 14
Remote Potentiometer
13 14
13 14
Optional Ground Connection
When connecting a single potentiometer to multiple drives it is important
to connect I/O Terminal 14 common together for all drives. I/O Terminal
14 common and I/O Terminal 13 (potentiometer wiper) should be daisychained to each drive. All drives must be powered up for the analog signal
to be read correctly.
Installing Control Wiring
6-9
6.5
Start and Speed Reference Control
The drive speed command can be obtained from a number of
different sources. The source is normally determined by P038
(Speed Reference). However, when A051 or A052 (Digital Inx
Select) is set to option 2, 4, 5, or 6, and the digital input is active,
A051 or A052 will override the speed reference commanded by
P038 (Speed Reference). See figure 6.2 for the override priority.
Jog Input
Enabled and Active:
A051, A052, A053
or A054 = 2, 11, 12
Drive will Start and Run
at Jog Speed.
Yes
Drive Stopped
(Not Running)
Yes
Direction comes from
I/O Terminal 03 Dir/Run REV
or
Jog Forward/Jog Reverse command
No
No
Local/Remote Input
Enabled and Active:
(Digital Inx Sel) = 5
Yes
Start, Speed, and Direction commands
come from Integral Keypad.
Yes
Start, Speed and Direction commands
come from RS485 (DSI) port.
No
Comm Select Input
Enabled and Active:
(Digital Inx Sel) = 6
No
Speed commands come from 0-10V.
0-10V Override
Enabled and Active:
(Digital Inx Sel) = 13
Yes
Start and Direction
follows P036 (Start Source)
or
Bi-Polar input when enabled.
No
4-20mA Override
Enabled and Active:
(Digital Inx Sel) = 14
Speed commands come from 4-20mA.
Yes
Start and Direction
follows P036 (Start Source).
No
PID Enabled:
A132 (PID Ref Select)
0
Yes
Run as specified by
A132 (PID Ref Select).
Start and Direction commands come
from P036 (Start Source).
No
Run as specified by
A071-A077 (Preset Freq 1-7).
A051/A052/A053
Preset Inputs Active
Yes
Start and Direction commands come
from P036 (Start Source).
No
Run as specified by
P038 (Speed Reference).
Start and Direction commands come
from P036 (Start Source).
Figure 6.2 – Override Priority for the Speed Reference Command
6-10
MD65 AC Drive User Manual
6.6
Accel/Decel Selection
The selection of Accel/Decel rates can be made through digital
inputs, RS485 communications and/or parameters. See figure 6.3.
Jog Input
Enabled and Active:
A051, A052, A053
or A054 = 2, 11,12
Yes
Drive Stopped
(Not Running)
Drive will Start and Run
at Jog Speed.
Yes
Drive will use A079 (Jog Accel/Decel)
No
No
RS485 Port
Controls Speed
Yes
Either
P039 (Accel Time 1)/P040 (Decel Time 1)
or
A067 (Accel Time 2)/A068 (Decel Time 2)
can be selected when
RS485 port is active.
Yes
A067 (Accel Time 2)/A068 (Decel Time 2)
is active when input is active.
Yes
P039 (Accel Time 1)/P040 (Decel Time 1);
A067 (Accel Time 2)/A068 (Decel Time 2)
determined by the active
Preset Frequency.
See A070-A077 (Preset Freq 0-7)
Yes
Either
P039 (Accel Time 1)/P040 (Decel Time 1)
or
A067 (Accel Time 2)/A068 (Decel Time 2)
can be selected by the Digit 3 setting
of the Step Logic parameters.
See A140-A147 (Stp Logic 0-7)
No
Input is programmed
as "Accel 2 & Decel 2"
A051, A052, A053
or A054 = 1
No
Speed is controlled
by (Preset Freq x)
No
Speed is controlled
by Stp Logic
No
P039 (Accel Time 1)/P040 (Decel Time 1)
are used.
Figure 6.3 – Accel/Decel Selection
Installing Control Wiring
6-11
6-12
MD65 AC Drive User Manual
CHAPTER 7
Completing the Installation
This chapter provides instructions on how to perform a final check
of the installation before and after power is applied to the drive.
!
7.1
ATTENTION: Only qualified electrical personnel
familiar with the construction and operation of this
equipment and the hazards involved should start and
adjust it. Read and understand this manual in its
entirety before proceeding. Failure to observe this
precaution could result in severe bodily injury or loss
of life.
Checking the Installation Before
Applying Power to the Drive
!
ATTENTION: The drive contains high voltage
capacitors that take time to discharge after removal of
mains supply. Before working on the drive, ensure
isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three (3) minutes for capacitors to
discharge to safe voltage levels. Darkened display
LEDs is not an indication that capacitors have
discharged to safe voltage levels. Failure to observe
this precaution could result in severe bodily injury or
loss of life.
ATTENTION: You must provide an external, hardwired
emergency stop circuit outside of the drive circuitry.
This circuit must disable the system in case of
improper operation. Uncontrolled machine operation
can result if this procedure is not followed. Failure to
observe this precaution could result in bodily injury.
To verify the condition of the installation:
•
Confirm that all inputs are connected to the correct terminals and
are secure.
•
Verify that AC line power at the disconnect device is within the
rated value of the drive.
•
Verify that any external digital control power is 24 volts DC.
Completing the Installation
7-1
•
Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set
to match your control wiring scheme. See figure 6.1 for the
location of this switch.
Important:
•
Verify that the Stop input is present or the drive will not start.
Important:
7.2
The default control scheme is Source (SRC). The
Stop terminal is jumpered (I/O Terminals 01 and 11) to
allow starting from the keypad. If the control scheme is
changed to Sink (SNK), the jumper must be removed
from I/O Terminals 01 and 11 and installed between
I/O Terminals 01 and 04.
If I/O Terminal 01 is used as a stop input, the jumper
between I/O Terminals 01 and 11 must be removed.
Powering Up After Installation is
Complete
To verify that the drive is installed correctly and is receiving the
proper line voltage, apply AC power and control voltages to the
drive.
Factory default parameter values allow the drive to be controlled
from the integral keypad. No programming is required to start, stop,
change direction, and control speed directly from the integral
keypad.
Become familiar with the integral keypad features before setting any
parameters. Refer to chapter 8 for information about the integral
keypad and programming the drive. To simplify drive setup, the
most commonly programmed parameters are organized in the
Basic parameter group.
If a fault code appears on power up, refer to chapter 10,
Troubleshooting the Drive, for an explanation of the fault code.
7-2
MD65 AC Drive User Manual
CHAPTER 8
Using the Integral Keypad
to Program and Control
the Drive
Factory-default parameter values allow the drive to be controlled
from the integral keypad. No programming is required to start, stop,
change direction, or control speed directly from the integral keypad.
This chapter provides an overview of the integrated keypad and
how to use it to program and control the MD65 drive.
Parameter descriptions are provided in chapter 9.
8.1
Keypad Components
– RUN
— FWD
REV
VOLTS
AMPS
HERTZ
™
PROGRAM
˜
šFAULT
PROG
›
MIN.
œ
MAX.
Refer to tables 8.1 and 8.2 for the LED and key descriptions noted
by through .
–
œ
Figure 8.1 – Integral Keypad
Using the Integral Keypad to Program and Control the Drive
8-1
8.1.1 Display Description
The alpha-numeric display indicates the following:
•
•
•
Parameter number
Parameter value
Fault code
8.1.2 LED Descriptions
Refer to figure 8.1 for the location of the LEDs described in table
8.1.
Table 8.1 – LED Descriptions
No.
–
—
LED
LED State
Description
RUN
Steady Red
Indicates the drive is running.
FWD
REV
Flashing
Red
Drive has been commanded to
change direction. Indicates actual
motor direction while decelerating
to zero.
Steady Red
Indicates the commanded motor
direction.
˜
VOLTS
AMPS
HERTZ
Steady Red
Indicates the units of the
parameter value being displayed.
™
PROGRAM
Steady Red
Indicates the drive is in program
mode and the parameter value
can be changed.
š
FAULT
Flashing
Red
Indicates the drive is faulted.
›
Pot Status
Steady
Green
Indicates the potentiometer on
integral keypad is active.
œ
Start Key Status
Steady
Green
Indicates the Start key on integral
keypad is active. The Reverse key
is also active unless disabled by
A095 (Reverse Disable).
8-2
MD65 AC Drive User Manual
8.1.3 Key Descriptions
Refer to figure 8.1 for the location of the keys described in table 8.2.
Table 8.2 – Key Descriptions
Key
Name
Program
PROG
Up Arrow
Down Arrow
Enter
Description
•
•
Enter/exit program mode.
•
Back up one step in
programming menu.
•
Cancel a change to a parameter
value.
•
Scroll through P and A
parameters.
•
Increase/decrease the value of
a flashing digit.
•
In Display Mode, increases/
decreases internal frequency
parameter if that parameter is
currently controlling the drive
commanded speed.
•
Display value of P or A
parameter.
•
Save a change to a parameter
value.
•
Scroll through display (d)
parameters.
Scroll through parameter
groups.
Potentiometer
Control drive speed. Default is
active. Controlled by parameter
P038.
Start
Start the drive. Default is active.
Controlled by parameter P036.
Reverse
Reverse direction of the motor.
Default is active. Controlled by
parameters P036 and A095.
Stop
•
Stop the drive (if drive is
running).
•
Clear fault (if drive is stopped) if
Stop is set up as Stop-Clear
Fault (P037 = 0, 1, 2, or 3).
Controlled by parameter P037.
Using the Integral Keypad to Program and Control the Drive
8-3
8.2
About Parameters
To program the drive for a specific application, you adjust the
appropriate parameters. The parameters are used to define
characteristics of the drive.
There are three types of parameters:
•
Numbered List Parameters
Numbered list parameters allow a selection from two or more
options. Each item is represented by a number.
Example: Start Source (P036)
•
Bit Parameters
Bit parameters have individual bits associated with features or
conditions. If the bit is 0, the feature is off or the condition is false.
If the bit is 1, the feature is on or the condition is true.
Example: Drive Status (d006)
•
Numeric Parameters
These parameters have a single numerical value (for example,
0.1 volts).
Example: Motor NP Volts (P031)
Parameters are also either configurable or tunable, or read-only.
Configurable parameters can be adjusted or changed only while
the drive is stopped.
Tunable parameters can be adjusted or changed while the drive is
running or stopped.
Read-only parameters cannot be adjusted.
8.3
How Parameters are Organized
Parameters are organized into three Parameter Groups:
8-4
•
The Basic Parameter Group (Pnnn) contains the most commonly
used parameters to simplify the start-up process.
•
The Advanced Parameter Group (Annn) contains parameters
used for more advanced applications.
•
The Display Parameter Group (dnnn) contains parameters that
indicate actual drive conditions.
MD65 AC Drive User Manual
8.4
Viewing and Adjusting Basic (P) and
Advanced (A) Parameters
Use the following procedure to view and adjust the Basic and
Advanced parameters.
Table 8.3 – Viewing and Adjusting Basic (P) and Advanced (A) Parameters
Procedure
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Sample Display
VOLTS
AMPS
HERTZ
PROG
Press
until the desired
parameter group is displayed.
The PROGRAM LED will turn
on to indicate the drive is in
program mode.
Press
to scroll
through the parameters in the
selected parameter group.
Press
to view the value
of the displayed parameter.
Press
or
.
The adjustable value will flash
on the display.
Use
value.
PROGRAM
VOLTS
AMPS
HERTZ
PROGRAM
Step 7.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
to adjust the
VOLTS
AMPS
HERTZ
PROGRAM
Step 6.
FAULT
Press
to accept the
value. The value stops
flashing.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
PROG
Press
to return to the
parameter number.
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
To adjust additional parameters, repeat steps 2 through 7.
To exit a parameter without saving the value, press
PROG
instead of
.
Using the Integral Keypad to Program and Control the Drive
8-5
8.5
Viewing the Display (d) Parameters
Use the procedure in table 8.4 to view Display parameters.
Table 8.4 – Viewing the Display (d) Parameters
Procedure
Step 1.
Step 2.
Step 3.
Sample Display
VOLTS
AMPS
HERTZ
PROG
Press
to scroll through
the parameter menus until the
Display Group parameters are
displayed. The PROGRAM
LED will be off to indicate the
drive is in display mode.
Press
to scroll through
the Display Group parameters
until the desired Display
parameter is displayed.
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
The parameter value will be
displayed 3 seconds after
is released.
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
To view additional Display parameters, press
to return to the
Display Group parameter list and scroll through the parameter list
as described in step 2.
Note that the last user-selected Display parameter is saved when
power is removed and is displayed by default when power is
re-applied.
8-6
MD65 AC Drive User Manual
CHAPTER 9
Parameter Descriptions
The following information is provided for each parameter along with
its description:
Parameter Number:
Unique number assigned to each
parameter.
Parameter Name:
Unique name assigned to each
parameter.
Range:
Predefined parameter limits or
selections.
Default:
Factory default setting.
See also:
Associated parameters that may provide
additional or related information.
What the Symbols Mean
Symbol
Meaning
Drive must be stopped before changing
parameter value.
32
32-bit parameter. Parameters marked
32-bit will have two parameter numbers
when using RS485 communications and
programming software.
The parameters are presented in numerical order in the sections
that follow. Refer to Appendix C for a list of parameters
cross-referenced by parameter name.
Parameter Descriptions
9-1
9.1
Basic Program Group Parameters
The Basic Program Group contains the most commonly used
parameters to simplify the start-up process.
P031 Motor NP Volts
Range:
20 VAC to Drive Rated Volts
Default:
Based on Drive Rating
See also:
d004, A084-A087
Set to the motor nameplate rated volts.
P032 Motor NP Hertz
Range:
15 to 400 Hz
Default:
60 Hz
See also:
A084-A087, A090
Set to the motor nameplate rated frequency.
P033 Motor OL Current
Range:
0.0 to (Drive Rated Amps x 2)
Default:
Based on Drive Rating
See also:
A055, A058, A061, A089, A090, A098, A114, A118
Set to the maximum allowable motor current. The drive will fault on
an F7 Motor Overload if the value of this parameter is exceeded by
150% for 60 seconds or 200% for 3 sec.
P034 Minimum Freq
Range:
0.0 to 400.0 Hz
Default:
0.0 Hz
See also:
d001, d002, d013, P035, A085-A087, A110, A112
Sets the lowest frequency the drive will output continuously.
P035 Maximum Freq
Range:
0 to 400 Hz
Default:
60 Hz
See also:
d001, d002, d013, P034, A065, A078, A085-A087,
A111, A113
Sets the highest frequency the drive will output.
9-2
MD65 AC Drive User Manual
P036 Start Source
Range:
0 = Keypad
1 = 3-Wire
2 = 2-Wire
3 = 2-W Lvl Sens
4 = 2-W Hi Speed
5 = Comm Port
Default:
0 = Keypad
See also:
d012, P037
Sets the control scheme used to start the drive.
Refer to section 6.5, Start and Speed Reference Control, for details
about how other drive settings can override the setting of this
parameter.
Important:
For all settings except option 3, the drive must receive
a leading edge from the start input for the drive to start
after a stop input, loss of power, or fault condition.
0 = Keypad (Default): Integral keypad controls drive operation. I/O
Terminal 01 (Stop) on terminal block = coast to stop. When 0 is
selected, the Reverse key is also active unless disabled by Reverse
Disable (A095).
1 = 3-Wire: I/O Terminal 01 (Stop) = stop according to the value set
in Stop Mode (P037). Refer to section 6.4.1 for wiring examples.
2 = 2-Wire: I/O Terminal 01 (Stop) = coast to stop. Refer to section
6.4.1 for wiring examples.
3 = 2-W Lvl Sens: Two-wire level-sensitive. Drive will restart after a
Stop command when Stop is removed and Start is held active.
!
ATTENTION: When Start Source (P036) is set to
3 = 2-W Lvl Sens, and the Run input is maintained,
the Run inputs do not need to be toggled after a Stop
input for the drive to run again. A Stop function is
provided only when the Stop input is active (open).
Failure to observe this precaution could result in
severe bodily injury.
4 = 2-W Hi Speed: Two-wire high-speed. Outputs are kept in a
ready-to-run state. The drive will respond to a Start command within
10 ms. I/O Terminal 01 (Stop) = coast to stop.
Important:
There is greater potential voltage on the power output
terminals (U/TI, V/T2, W/T3) when using this option.
5 = Comm Port: Remote communications. I/O Terminal 01 (Stop) =
coast to stop.
Parameter Descriptions
9-3
P037 Stop Mode
Range:
0 = Ramp, CF
1 = Coast, CF
2 = DC Brake, CF
3 = DCBrkAuto, CF
4 = Ramp
5 = Coast
6 = DC Brake
7 = DC BrakeAuto
Default:
1 = Coast, CF
See also:
P036, A080, A081, A082, A105
Active stop mode for all stop sources [for example, keypad, run
forward (I/O Terminal 02), run reverse (I/O Terminal 03), RS485
port] except as noted below.
Important:
I/O Terminal 01 is always a coast-to-stop input except
when Start Source (P036) is set for three-wire control.
When three-wire control is selected, I/O Terminal 01 is
controlled by Stop Mode (P037).
Hardware Enable Circuitry
By default, I/O Terminal 01 is a coast-to-stop input. The status of the
input is interpreted by drive software. If the application requires the
drive to be disabled without software interpretation, a “dedicated”
hardware enable configuration can be used. This is accomplished
by removing the ENBL enable jumper on the control board. In this
case, the drive will always coast to a stop regardless of the setting
of Start Source (P036) and Stop Mode (P037).
0 = Ramp, CF1 (Default): Ramp to stop. Stop command clears
active fault.
1 = Coast, CF1: Coast to stop. Stop command clears active fault.
2 = DC Brake, CF1: DC injection braking stop. Stop command
clears active fault.
3 = DC BrkAuto, CF1: DC injection braking stop with auto shutoff.
Standard DC injection braking for the amount of time set in DC
Brake Time (A080), or the drive shuts off when the drive detects that
the motor is stopped.
Stop command clears active fault.
4 = Ramp: Ramp to stop.
5 = Coast: Coast to stop.
1
9-4
Stop Input also clears active fault.
MD65 AC Drive User Manual
6 = DC Brake: DC injection braking stop.
7 = DC BrakeAuto: DC injection braking stop with auto shutoff.
Standard DC injection braking for the amount of time set in DC
Brake Time (A080), or the drive shuts off if current limit is exceeded.
P038 Speed Reference
Range:
0 = Drive Pot
1 = InternalFreq
2 = 0-10V Input
3 = 4-20mA Input
4 = Preset Freq
5 = Comm Port
6 = Stp Logic
Default:
0 = Drive Pot
See also:
d001, d002, d012, P039, P040, A051-A054, A069,
A070-A077, A110-A113, A123, A132, A140-A147,
A150-A157
Sets the source of the speed reference to the drive.
The drive speed command can be obtained from a number of
different sources. The source is normally determined by Speed
Reference (P038). However, when Digital Inx Sel (A051-A054) is
set to option 2, 4, 5, 6, 11, 12, 13, 14, or 15, and the digital input is
active, or if PID Ref Sel (A132) is not set to option 0, the speed
reference commanded by Speed Reference (P038) will be
overridden. Refer to the flowchart in figure 6.2 for more information
on speed reference control priority.
0 = Drive Pot (Default): Internal frequency command from the
potentiometer on the integral keypad.
1 = InternalFreq: Internal frequency command from Internal Freq
(A069).
2 = 0-10V Input: External frequency command from the 0 to 10 V or
+/-10 V analog input or remote potentiometer.
3 = 4-20mA Input: External frequency command from the 4 to
20 mA analog input.
4 = Preset Freq: External frequency command as defined by
Preset Freq x (A070-A077) when Digital Inx Sel (A051-A054) are
programmed as “Preset Frequencies,” and the digital inputs are
active.
5 = Comm Port: External frequency command from the
communications port.
6 = Stp Logic: External frequency command as defined by Preset
Freq x (A070-A077) and Stp Logic x (A140-A147).
Parameter Descriptions
9-5
P039 Accel Time 1
Range:
0.0 to 600.0 sec
Default:
5.0 sec
See also:
P038, P040, A051-A054, A067, A070-A077,
A140-A147
Sets the rate of acceleration for all speed increases. See figure 9.1.
Maximum Frequency / Accel Time = Accel Rate
P035 [Maximum Freq]
Acc
tion
ele
era
cel
ratio
n
De
Speed
0
0
P039 or A067
[Accel Time x]
Time
P040 or A068
[Decel Time x]
Figure 9.1 – Accel Time 1 (P039)
P040 Decel Time 1
Range:
0.1 to 600.0 sec
Default:
5.0 sec
See also:
P038, P039, A051-A054, A068, A070-A077,
A140-A147
Sets the rate of deceleration for all speed decreases. See figure 9.2.
Maximum Frequency / Decel Time = Decel Rate
P035 [Maximum Freq]
0
0
P039 or A067
[Accel Time x]
n
Acc
ele
tio
era
cel
ratio
n
De
Speed
Time
P040 or A068
[Decel Time x]
Figure 9.2 – Decel Time 1 (P040)
9-6
MD65 AC Drive User Manual
P041 Reset To Defalts
Range:
0 = Ready/Idle
1 = Factory Rset
Default:
0 = Ready/Idle
See also:
N/A
Setting this parameter to 1 resets all parameter values to factory
defaults. After the reset function is complete, this parameter sets
itself back to 0. This selection causes an F48 Params Defaulted
fault.
Parameter Descriptions
9-7
9.2
A051
A052
A053
A054
Advanced Group Parameters
Digital In1 Sel (I/O Terminal 05)
Digital In2 Sel (I/O Terminal 06)
Digital In3 Sel (I/O Terminal 07)
Digital In4 Sel (I/O Terminal 08)
Range:
0 = Not Used
1 = Acc & Dec 2
2 = Jog
3 = Aux Fault
4 = Preset Freq
5 = Local
6 = Comm Port
7 = Clear Fault
8 = RampStop,CF
9 = CoastStop,CF
10 = DCInjStop,CF
11 = Jog Forward
12 = Jog Reverse
13 = 10V In Ctrl
14 = 20mA In Ctrl
15 = PID Disable
16 = MOP Up
17 = MOP Down
18 = Timer Start
19 = Counter In
20 = Reset Timer
21 = Reset Countr
22 = Rset Tim&Cnt
23 = Logic In1
24 = Logic In2
25 = Current Lmt2
Default:
A051, A052, A053: 4 = Preset Freq
A054: 5 = Local
See also:
d012, d014, P038-P040, A067, A068, A070-A079,
A188, A140-A147
Selects the function for the digital inputs. Refer to the flowchart in
section 6.6 for more information on speed reference control priority.
0 = Not Used: Terminal has no function but can be read over
network communications using Dig In Status (d014).
1 = Acc & Dec 2: When this option is selected, Accel Time 2 (A067)
and Decel Time 2 (A068) are used for all ramp rates except Jog.
This can only be tied to one input. Refer to the flowchart in figure 6.3
for more information about accel/decel selection.
9-8
MD65 AC Drive User Manual
2 = Jog: When the input is present, the drive accelerates according
to the value set in Jog Accel/Decel (A079) and ramps to the value
set in Jog Frequency (A078). When the input is removed, the drive
ramps to a stop according to the value set in Jog Accel/Decel
(A079). A valid Start command will override this input.
3 = Aux Fault: When enabled, an F2 Auxiliary Input fault will occur
when the input is removed.
4 = Preset Freq (Default for A051, A052, and A053): Refer to
Preset Freq x (A070 to A077).
Important:
Digital inputs have priority for frequency control when
programmed as Preset Speed and are active. Refer to
the flowchart in figure 6.2 for more information on
speed reference control priority.
5 = Local (Default for A054): When active, sets the integral keypad
as the start source and the potentiometer on the integral keypad as
the speed source.
6 = Comm Port: When active, sets communications device as
default start/speed command source. This can only be tied to one
input.
7 = Clear Fault: When active, clears an active fault.
8 = RampStop,CF: Causes drive to immediately ramp to a stop
regardless of how Stop Mode (P037) is set. Stop input clears active
fault.
9 = CoastStop,CF: Causes drive to immediately coast to a stop
regardless of how Stop Mode (P037) is set. Stop input clears active
fault.
10 = DCInjStop,CF: Causes drive to immediately begin a DC
injection stop regardless of how Stop Mode (P037) is set. Stop input
clears active fault.
11 = Jog Forward : Drive accelerates to Jog Frequency (A078)
according to Jog Accel/Decel (A079) and ramps to stop when input
becomes inactive. A valid start will override this command.
12 = Jog Reverse: Drive accelerates to Jog Frequency (A078)
according to Jog Accel/Decel (A079) and ramps to stop when the
input becomes inactive. A valid start will override this command.
13 = 10V In Ctrl: Selects 0-10 V or +/10 V control as the frequency
reference. Start source is not changed.
14 = 20mA In Ctrl: Selects 4-20 mA control as the frequency
reference. Start source is not changed.
Parameter Descriptions
9-9
15 = PID Disable: Disables PID function. Drive uses the next valid
non-PID speed reference.
16 = MOP Up: Increases the value of Internal Freq (A069) at a rate
of 2 Hz per second. Default for A069 is 60 Hz.
17 = MOP Down: Decreases the value of Internal Freq (A069) at a
rate of 2 Hz per second. Default for A069 is 60 Hz.
18 = Timer Start: Clears and starts the timer function. May be used
to control the relay or opto outputs.
19 = Counter In: Starts the counter function. May be used to control
the relay or opto outputs.
20 = Reset Timer: Clears the active timer.
21 = Reset Countr: Clears the active counter.
22 = Rset Tm&Cnt: Clears the active time and counter.
23 = Logic In1: Logic function input number 1. May be used to
control the relay or opto outputs (see parameters A055, A058,
A061, options 11-14). May be used with Step Logic parameters
A140-A147.
24 = Logic In2: Logic function input number 2. May be used to
control the relay or opto outputs (see parameters A055, A058,
A061, options 11-14). May be used with Step Logic parameters
A140-A147.
25 = Current Lmt2: When active, Current Limit 2 (A118)
determines the drive current limit level.
9-10
MD65 AC Drive User Manual
A055 Relay Out Sel
Range:
0 = Ready/Fault
1 = At Frequency
2 = MotorRunning
3 = Reverse
4 = Motor Overld
5 = Ramp Reg
6 = Above Freq
7 = Above Cur
8 = Above DCVolt
9 = Retries Exst
10 = Above Anlg V
11 - Logic In 1
12 = Logic In 2
13 = Login 1 & 2
14 = Logic 1 or 2
15 = StpLogic Out
16 = Timer Out
17 = Counter Out
18 = Above PF Ang
19 = Anlg In Loss
20 = ParamControl
Default:
0 = Ready/Fault
See also:
P033, A056, A092, A140-A147, A150-A157
Sets the condition that changes the state of the output relay
contacts.
0 = Ready/Fault (Default): Relay changes state when power is
applied. This indicates that the drive is ready for operation. Relay
returns drive to shelf state when power is removed or a fault occurs.
1 = At Frequency: Drive reaches commanded frequency.
2 = MotorRunning: Motor is receiving power from the drive.
3 = Reverse: Drive is commanded to run in reverse direction.
4 = Motor Overload: Motor overload condition exists.
5 = Ramp Reg: Ramp regulator is modifying the programmed
accel/decel times to avoid an overcurrent or overvoltage fault.
6 = Above Freq: Drive exceeds the frequency (Hz) value set in
Relay Output Level (A056). Use A056 to set the threshold.
7 = Above Cur: Drive exceeds the current (% Amps) value set in
Relay Output Level (A056). Use A056 to set the threshold.
Important:
The value for Relay Output Level must be entered in
percent of drive rated output current.
8 = Above DCVolt: Drive exceeds the DC bus voltage value set in
Relay Output Level (A056). Use A056 to set the threshold.
Parameter Descriptions
9-11
9 = Retries Exst: Number of retries set in Auto Rstrt Tries (A092) is
exhausted.
10 = Above Anlg V: The analog input voltage (I/O Terminal 13)
exceeds the value set in Relay Out Level (A056). Do not use if 10V
Bipolar Enbl (A123) is set to 1 = Bi-Polar In.
11 = Logic In 1: An input is programmed as Logic In 1 and is active.
12 = Logic In 2: An input is programmed as Logic In 2 and is active.
13 = Logic 1 & 2: Both logic inputs are programmed and active.
14 = Logic 1 or 2: One or both logic inputs are programmed and
one or both is active.
15 = StpLogic Out: Drive enters Step Logic step with digit 3 of the
Command Word (A140-A147) set to enable the Step Logic output.
16 = Timer Out: The timer has reach the value set in Relay Out
Level (A056). Use A056 to set the threshold.
17 = Counter Out: The counter has reached the value set in Relay
Out Level (A056). Use A056 to set the threshold.
18 = Above PF Ang: The Power Factor angle has exceeded the
value set in Relay Out Level (A056). Use A056 to set the threshold.
19 = Anlg In Loss: Analog input loss has occurred. Program
Analog In Loss (A122) for the desired action when input loss
occurs.
20 = ParamControl: Enables the output to be controlled over
network communications by writing to Relay Out Level (A056).
0 = Off, 1 = On.
9-12
MD65 AC Drive User Manual
A056 Relay Out Level
32
Range:
0.0 to 9999 (see table 9.1)
Default:
0.0
See also:
A055, A058, A061
Sets the trip point for the output relay if the value of Relay Out Sel
(A055) is 6, 7, 8, 10, 16, 17, 18, or 20. See table 9.1.
Table 9.1 – Trip Points for Digital Output Relay
A055 Setting
6 (Above Freq)
A056 Range
0 to 400 Hz
7 (Above Cur)
0 to 180%
8 (Above DCVolt)
0 to 815 V
10 (Above Anlg V)
16 (Timer Out)
0 to 100%
0.1 to 9999 seconds
17 (Counter Out)
1 to 9999 counts
18 (Power Factor Angle)
1 to 180 degrees
20 (ParamControl)
Parameter Descriptions
0, 1
9-13
A058 Opto Out1 Sel
A061 Opto Out2 Sel
Range:
0 = Ready/Fault
1 = At Frequency
2 = MotorRunning
3 = Reverse
4 = Motor Overld
5 = Ramp Reg
6 = Above Freq
7 = Above Cur
8 = Above DCVolt
9 = Retries Exst
10 = Above Anlg V
11 = Logic In 1
12 = Logic In 2
13 = Logic 1 & 2
14 = Logic 1 or 2
15 = StpLogic Out
16 = Timer Out
17 = Counter Out
18 = Above PF Ang
19 = Anlg In Loss
20 = ParamControl
Default:
A058: 0 = Ready/Fault
A061: 2 = MotorRunning
See also:
A056, A092, A140-A147, A150-A157, P033
Determines the operation of the programmable opto outputs.
0 = Ready/Fault (A058 Default): Opto outputs are active when
power is applied. This indicates that the drive is ready for operation.
Opto outputs are inactive when power is removed or a fault occurs.
1 = At Frequency: Drive reaches commanded frequency.
2 = MotorRunning (A061 Default): Motor is receiving power from
the drive.
3 = Reverse: Drive is commanded to run in reverse direction.
4 = Motor Overld: Motor overload condition exists.
5 = Ramp Reg: Ramp regulator is modifying the programmed
accel/decel times to avoid an overcurrent or overvoltage fault from
occurring.
6 = Above Freq: Drive exceeds the frequency (Hz) value set in
Opto Outx Level (A059 or A062). Use A059 or A062 to set the
threshold.
Important:
9-14
The value for A059 or A062 must be entered in
percent of drive rated output current.
MD65 AC Drive User Manual
8 = Above DCVolt: Drive exceeds the DC bus voltage value set in
Opto Outx Level (A059 or A062). Use A059 or A062 to set the
threshold.
9 = Retries Exst: The value set in Auto Rstrt Tries (A092) is
exceeded.
10 = Above Anlg V: The analog input voltage (I/O Terminal 13)
exceeds the value set in Relay Out Level (A056). Do not use if 10 V
Bipolar Enbl (A123) is set to 1 = Bi-Polar In.
11 = Logic In 1: An input is programmed as Logic In 1 and is active.
12 = Logic In 2: An input is programmed as Logic In 2 and is active.
13 = Logic 1 & 2: Both logic inputs are programmed and active.
14 = Logic 1 or 2: One or both logic inputs are programmed and
one or both is active.
15 = StpLogic Out: Drive enters Step Logic step with digit 3 of the
Command Word (A140-A147) set to enable the Step Logic output.
16 = Timer Out: The timer has reached the value set in Opto Outx
Level (A059 or A062). Use A059 or A062 to set the threshold.
17 = Counter Out: The counter has the reached the value set in
Opto Outx Level (A059 or A062). Use A059 or A062 to set the
threshold.
18 = Above PF Ang: The Power Factor angle has exceeded the
value set in Opto Outx Level (A059 or A062). Use A059 or A062 to
set the threshold.
19 = Anlg In Loss: An analog input loss has occurred. Program
Analog In Loss (A122) for action desired when input loss occurs.
20 = ParamControl: Enables the output to be controlled over
network communications by writing to Opto Outx Level (A059 to
A062). (0=Off, 1=On)
Parameter Descriptions
9-15
A059 Opto Out1 Level
A062 Opto Out2 Level
32
Range:
0.0 to 9999
Default:
0.0
See also:
A058, A061
Determines the on/off point for the opto outputs when Opto Outx Sel
(A058 or A061) is set to option 6, 7, 8, 10, 16, 17, 18, or 20. Refer to
table 9.2.
Table 9.2 – On/Off Points for the Opto Outputs
A058 & A061 Setting
A059 & A062 Range
6 (Above Freq)
0 to 400 Hz
7 (Above Cur)
0 to 180%
8 (Above DCVolt)
0 to 815 V
10 (Above Anlg V)
0 to 100%
16 (Timer Out)
0.1 to 9999 seconds
17 (Counter Out)
1 to 9999 counts
18 (Above PF Ang)
1 to 180 degrees
20 (ParamControl)
0, 1
A064 Opto Out Logic
Range:
0 to 3 (see table 9.3)
Default:
0
See also:
N/A
Determines the logic (Normally Open/NO or Normally Closed/NC)
of the opto outputs. Refer to table 9.3.
Table 9.3 – A064 Options
A064
Option
9-16
Opto Out1 Logic
Opto Out2 Logic
0
NO (Normally Open)
NO (Normally Open)
1
NC (Normally Closed)
NO (Normally Open)
2
NO (Normally Open)
NC (Normally Closed)
3
NC (Normally Closed)
NC (Normally Closed)
MD65 AC Drive User Manual
A065 Analog Out Sel
Range:
0 to 14
Default:
0
See also:
A066, P035
Sets the analog output signal mode (0-10 V, 0-20 mA, or 4-20 mA).
The output is used to provide a signal that is proportional to several
drive conditions.
Table 9.4 – Analog Output Signal Mode Selections
Option
0 = OutFreq 0-10
1 = OutCurr 0-10
2 = OutVolt 0-10
3 = OutPowr 0-10
4 = TstData 0-10
5 = OutFreq 0-20
6 = OutCurr 0-20
7 = OutVolt 0-20
8 = OutPowr 0-20
9 = TstData 0-20
10 = OutFreq 4-20
11 = OutCurr 4-20
12 = OutVolt 4-20
13 = OutPowr 4-20
14 = TstData 4-20
Output
Range
0-10 V
0-10 V
0-10 V
0-10 V
0-10 V
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
4-20 mA
4-20 mA
4-20 mA
4-20 mA
4-20 mA
Minimum
Output Value
0 V = 0 Hz
0 V = 0 Amps
0 V = 0 Volts
0 V = 0 kW
0 V = 0000
0 mA = 0 Hz
0 mA = 0 Amps
0 mA = 0 Volts
0 mA = 0 kW
0 mA = 0000
4 mA = 0 Hz
4 mA = 0 Amps
4 mA = 0 Volts
4 mA = 0 kW
4 mA = 0000
Maximum Output Value
A066 (Analog Out High)
P035 (Maximum Freq)
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 (Maximum Freq)
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 (Maximum Freq)
200% Drive Rated Output Current
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
DIP
Switch
Position
0-10 V
0-10 V
0-10 V
0-10 V
0-10 V
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
A066 Analog Out High
Range:
0 to 800%
Default:
100%
See also:
A065
Scales the Maximum Output Value for the Analog Out Sel (A065)
source setting.
For example:
A066 Setting
A065 Setting
50%
1 = OutCurr 0-10
90%
8 = OutPowr 0-20
Parameter Descriptions
A065 Max. Output Value
5 V for 200% Drive Rated Output Current
18 mA for 200% Drive Rated Power
9-17
A067 Accel Time 2
Range:
0.0 to 600.0 sec
Default:
10.0 sec
See also:
P039, A051-A054, A070-A077, A140-A147
Sets the rate of acceleration for speed increases except jog. Refer
to the flowchart in figure 6.3 for details. Refer to figure 9.3.
Maximum Frequency / Accel Time = Accel Rate
P035 [Maximum Freq]
0
0
n
Acc
ele
tio
era
cel
ratio
n
De
Speed
P039 or A067
[Accel Time x]
Time
P040 or A068
[Decel Time x]
Figure 9.3 – Accel Time 2 (A067)
A068 Decel Time 2
Range:
0.1 to 600.0 sec
Default:
10.0 sec
See also:
P040, A051-A054, A070-A077, A140-A147
Sets the rate of deceleration for speed decreases except jog. Refer
to the flowchart in figure 6.3 for details. See figure 9.4.
Maximum Frequency / Decel Time = Decel Rate
P035 [Maximum Freq]
0
0
P039 or A067
[Accel Time x]
n
Acc
ele
tio
era
cel
ratio
n
De
Speed
Time
P040 or A068
[Decel Time x]
Figure 9.4 – Decel Time 2 (A068)
9-18
MD65 AC Drive User Manual
A069 Internal Freq
Range:
0.0 to 400.0 Hz
Default:
0.0 Hz
See also:
P038
Provides the frequency command to the drive when Speed
Reference (P038) is set to 1=Internal Frequency. When enabled,
this parameter will change the frequency command in “real time”
using the integral keypad
Important:
keys when in program mode.
Once the desired command frequency is reached, the
key must be pressed to store this value to
EEPROM memory. If the
PROG
key is used before the
key, the frequency will return to the original value
following the normal accel/decel curve.
If Digital Inx Sel (A-051-A054) is set to 16 = MOP Up or 17 = MOP
Down, this parameter acts as the MOP frequency reference.
Parameter Descriptions
9-19
A0701
A0711
A0721
A0731
A0741
A0751
A0761
A0771
Preset Freq 01
Preset Freq 1
Preset Freq 2
Preset Freq 3
Preset Freq 4
Preset Freq 5
Preset Freq 6
Preset Freq 7
Range:
0.0 to 400.0 Hz
Default:
0.0 Hz
See also:
P038, P039, P040, A051-A053, A067, A068,
A140-A147, A150-A157
1
To activate Preset Freq 0, set P038 (Speed Reference) to 4 = Preset Freq
Provides a fixed frequency command value when Digital Inx Sel
(A051-A053) is set to 4 = Preset Frequencies. An active preset
input will override the speed command as shown in the flowchart in
figure 6.2. See table 9.5.
Table 9.5 – Selecting the Reference Source Using Presets
Input State
of Digital In 1
(I/O Terminal 05
when A051 = 4)
Input State
of Digital In 2
(I/O Terminal 06
when A052 = 4)
Input State
of Digital In 3
(I/O Terminal 07
when A053 = 4)
Frequency Source
Accel / Decel Parameter Used1
0
0
0
A070 (Preset Freq 0)
Accel Time 1 / Decel Time 1
1
0
0
A071 (Preset Freq 1)
Accel Time 1 / Decel Time 1
0
1
0
A072 (Preset Freq 2)
Accel Time 2 / Decel Time 2
1
1
0
A073 (Preset Freq 3)
Accel Time 2 / Decel Time 2
0
0
1
A074 (Preset Freq 4)
Accel Time 1 / Decel Time 1
1
0
1
A075 (Preset Freq 5)
Accel Time 1 / Decel Time 1
0
1
1
A076 (Preset Freq 6)
Accel Time 2 / Decel Time 2
1
1
1
A077 (Preset Freq 7)
Accel Time 2 / Decel Time 2
1
When a digital input is set to “Accel 2 & Decel 2,” and the input is active, that input overrides the settings in this
table.
A078 Jog Frequency
Range:
0.0 to Maximum Frequency (P035)
Default:
10.0 Hz
See also:
P035, A051-A054, A079
Sets the output frequency when a jog command is issued. See
parameters A051-A054 for information on how to jog the drive.
9-20
MD65 AC Drive User Manual
A079 Jog Accel/Decel
Range:
0.1 to 600.0 sec
Default:
10.0 sec
See also:
A051-A054, A078
Sets the acceleration and deceleration time when a jog command is
issued. Refer to parameters A051-A054 for information on how to
jog the drive.
.
A080 DC Brake Time
Range:
0.0 to 99.9 sec (A setting of 99.9 = Continuous)
Default:
0.0 sec
See also:
P037, A081
Sets the length of time that DC brake current is “injected” into the
motor. Refer to DC Brake Level (A081).
A081 DC Brake Level
Range:
0.0 to (Drive Rated Amps x 1.8)
Default:
Drive Rated Amps x 0.05
See also:
P037, A080
Defines the maximum DC brake current, in amps, applied to the
motor when Stop Mode (P037) is set to either DC Brake or Ramp.
See figure 9.5.
ATTENTION: If a hazard of injury due to movement
of equipment or material exists, an auxiliary
mechanical braking device must be used.
!
ATTENTION: This feature should not be used with
synchronous or permanent magnet motors. Motors
may be demagnetized during braking.
Ramp-to-Stop Mode
DC Injection Braking Mode
Vo
lta
ge
[DC Brake Time]
Spe
ed
Volts/Speed
Volts/Speed
Voltage
Speed
[DC Brake Time]
[DC Brake Level]
[DC Brake Level]
Time
Time
Stop Command
Stop Command
Figure 9.5 – DC Brake Level (A081)
Parameter Descriptions
9-21
A082 DB Resistor Sel
Range:
0 = Disabled
1 = Normal RA Resistor (5% Duty Cycle)
2 = No Protection (100% Duty Cycle)
3 to 99 = Duty Cycle Limited (3% to 99% Duty
Cycle)
Default:
0 = Disabled
See also:
P037
Enables/disables external dynamic braking.
A083 S Curve %
Range:
0 to 100%
Default:
0% (Disabled)
See also:
N/A
Sets the percentage of acceleration or deceleration time that is
applied to the ramp as an S Curve. Time is added, 1/2 at the
beginning and 1/2 at the end of the ramp.
For example: If Accel Time = 10 seconds, and the S Curve %
setting is 50%, the S Curve time will be 10 x 0.5 = 5 seconds. The
total time will be 10 + 5 = 15 seconds.
See figure 9.6 for an example.
Accel Time = 10 sec
S Curve% = 50%
S Curve Time = 10 x 0.5 = 5 sec
Total Time = 10 + 5 = 15 sec
50% S Curve
Target
Target/2
1/2 S Curve Time
2.5 Seconds
Accel Time
10 Seconds
1/2 S Curve Time
2.5 Seconds
Total Time to Accelerate = Accel Time + S Curve Time
Figure 9.6 – S Curve % (A083) Example
9-22
MD65 AC Drive User Manual
A084 Boost Select
Range:
0 = Custom V/Hz
Variable Torque (typical fan/pump curves):
1 = 30.0, VT
2 = 35.0, VT
3 = 40.0, VT
4 = 45.0, VT
Constant Torque:
5 = 0.0 no IR Compensation
6 = 0.0
7 = 2.5, CT
8 = 5.0, CT
9 = 7.5, CT
10 = 10.0, CT
11 = 12.5, CT
12 = 15.0, CT
13 = 17.5, CT
14 = 20.0, CT
Default:
8 = 5.0, CT
7 = 2.5, CT (for 4.0, 5.5, 7.5 kW (5.0, 7.5, and 10.0 HP)
drives only)
See also:
d004, P031, P032, A085-A087, A125
Sets the boost voltage (% of Motor NP Volts (P031)) and redefines
the Volts per Hz curve. Active when Torque Perf Mode (A125) is set
to 0 = V/Hz. Note that the drive may add additional voltage unless
option 5 is selected. See figure 9.7.
1/2 [Motor NP Volts]
50
1/2
[Motor NP Hertz]
% P031 [Motor NP Volts]
100
Settings
5-14
0
4
3
2
1
50
% P032 [Motor NP Hertz]
100
Figure 9.7 – Boost Select (A084)
Parameter Descriptions
9-23
A085 Start Boost
Range:
0.0 to 25.0%
Default:
5.0%
See also:
P031, P032, P034, P035, A084, A086, A087, A088,
A125
Sets the boost voltage (% of Motor NP Volts (P031)) and redefines
the Volts per Hz curve when Boost Select (A084) is set to 0 = Cust
V/Hz, and Torque Perf Mode (A125) is set to 0 = V/Hz.
A088 [Maximum Voltage]
A085 [Start Boost]
A086 [Break Voltage]
Voltage
P031 [Motor NP Volts]
A087 [Break Frequency]
A034 [Minimum Freq]
P032 [Motor NP Hertz]
Frequency
P035 [Maximum Freq]
Figure 9.8 – Start Boost (A085)
A086 Break Voltage
Range:
0.0 to 100.0%
Default:
25.0%
See also:
P031, P032, P034, P035, A084, A085, A087, A088,
A125
Sets the frequency where break voltage is applied when Boost
Select (A084) is set to 0 = Custom V/Hz, and Torque Perf Mode
(A125) is set to 0 = V/Hz.
9-24
MD65 AC Drive User Manual
A087 Break Frequency
Range:
0.0 to 400.0 Hz
Default:
15.0 Hz
See also:
P031, P032, P034, P035, A084, A085, A086, A088,
A125
Sets the frequency where the break frequency is applied when
Boost Select (A084) is set to 0 = Custom V/Hz, and Torque Perf
Mode (A125) is set to 0 = V/Hz.
A088 Maximum Voltage
Range:
20 to Drive Rated Volts
Default:
Drive Rated Volts
See also:
d004, A085, A086, A087
Sets the highest voltage the drive will output.
A089 Current Limit 1
Range:
0.1 to (Drive Rated Amps x 1.8)
Default:
Drive Rated Amps x 1.8
See also:
P033, A118
Maximum output current allowed before current limiting occurs.
A090 Motor OL Select
Range:
0 = No Derate
1 = Min Derate
2 = Max Derate
Default:
0 = No Derate
See also:
P032
No Derate
Min Derate
100
100
80
80
60
60
40
40
20
20
0
0
25 50 75 100 125 150 175 200
0
0
25 50 75 100 125 150 175 200
% of P033 [Motor OL Curent]
The drive provides Class 10 motor overload protection. Settings 0-2
select the derating factor for the I2t overload function. See figure
9.9.
Max Derate
100
80
60
40
20
0
0
25 50 75 100 125 150 175 200
Figure 9.9 – Motor OL Select (A090)
Parameter Descriptions
9-25
.
A091 PWM Frequency
Range:
2.0 to 16.0 kHz
Default:
4.0 kHz
See also:
A124
Sets the carrier frequency for the PWM output waveform. Figure
9.10 provides derating guidelines based on the PWM frequency
setting.
Important:
Ignoring derating guidelines can cause reduced drive
performance.
100
96
92
88
84
80
76
72
68
64
60
56
52
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Figure 9.10 – Derating Guidelines Based on PWM Frequency (A091)
Selection
A092 Auto Rstrt Tries
Range:
0 to 9
Default:
0
See also:
A055, A058, A061, A093
Sets the maximum number of times the drive attempts to reset a
fault and restart. Refer to section 10.1.2 for more information on the
Auto Restart/Run feature.
!
9-26
ATTENTION: Equipment damage and/or personal
injury may result if this parameter is used in an
inappropriate application. Do not use this function
without considering applicable local, national, and
international codes, standards, regulations, or
industry guidelines.
MD65 AC Drive User Manual
A093 Auto Rstrt Delay
Range:
0.0 to 300.0 sec
Default:
1.0 sec
See also:
A092
Sets the time between restart attempts when Auto Rstrt Tries
(A092) is set to a value other than zero. Refer to section 10.1.2 for
more information on the Auto Restart/Run feature.
A094 Start At PowerUp
Range:
0 = Disabled
1 = Enabled
Default:
0 = Disabled
See also:
N/A
Enables/disables a feature that allows a Start or Run command to
automatically cause the drive to resume running at commanded
speed after drive input power is restored. Requires a digital input
configured for Run or Start and a valid start contact.
This parameter will not function if Start Source (P036) is set to
4 = 2-W High Speed.
!
ATTENTION: Equipment damage and/or personal
injury may result if this parameter is used in an
inappropriate application. Do not use this function
without considering applicable local, national, and
international codes, standards, regulations, or
industry guidelines.
A095 Reverse Disable
Range:
0 = Rev Enabled
1 = Rev Disabled
Default:
0 = Rev Enabled
See also:
d006
Enables/disables the function that allows the direction of motor
rotation to be changed. The reverse command may come from a
digital command, the keypad, or a serial command. All reverse
inputs including two-wire Run Reverse will be ignored with reverse
disabled.
Parameter Descriptions
9-27
A096 Flying Start En
Range:
0 = Disabled
1 = Enabled
Default:
0 = Disabled
See also:
N/A
Enables/disables feature that allows the drive to reconnect to a
spinning motor at actual RPM.
!
ATTENTION: When starting with this feature
enabled, the motor may temporarily run up to the
maximum speed setting before settling at the speed
setpoint. Stay clear of rotating machinery. Failure to
observe this precaution could result in bodily injury.
A097 Compensation
Range:
0 = Disabled
1 = Electrical
2 = Mechanical
3 = Both
Default:
1 = Electrical
See also:
N/A
Enables/disables correction options that may improve problems
with motor instability.
1 = Electrical: Some drive/motor combinations have inherent
instabilities that are exhibited as non-sinusoidal motor currents. This
setting attempts to correct this condition.
2 = Mechanical: Some motor/load combinations have mechanical
resonances that can be excited by the drive current regulator. This
setting slows down the current regulator response and attempts to
correct this condition.
A098 SW Current Trip
Range:
0.0 to (Drive Rated Amps x 2)
Default:
0.0 (Disabled)
See also:
P033
Enables/disables a software instantaneous (within 100 ms) current
trip.
9-28
MD65 AC Drive User Manual
A099 Process Factor
Range:
0.1 to 999.9
Default:
30.0
See also:
d010
Scales the value displayed by Process Display (d010).
Output Frequency x Process Factor = Process Display
A100 Fault Clear
Range:
0 = Ready/Idle
1 = Reset Fault
2 = Clear Buffer (d007 - d009)
Default:
0 = Ready/Idle
See also:
d007 - d009
Resets a fault and clears the fault buffer (parameters d007 through
d009). Used primarily to clear a fault over network communications.
1 = Reset Fault: Clears the active fault and resets the drive.
2 = Clear Buffer: Clears fault codes from parameters d007 through
d009.
A101 Program Lock
Range:
0 = Unlocked
1 = Locked
Default:
0 = Unlocked
See also:
N/A
When set to 1 = Locked, protects parameters against change by
unauthorized personnel.
A102 Testpoint Sel
Range:
0 to FFFF
Default:
400
See also:
d019
Used by Rockwell Automation field service personnel.
Parameter Descriptions
9-29
A103 Comm Data Rate
Range:
0 = 1200
1 = 2400
2 = 4800
3 = 9600
4 = 19.2 K
5 = 38.4 K
Default:
4 = 19.2 K
See also:
d015
Sets the serial port rate for the RS485 port.
Important:
Power to the drive must be cycled before any changes
will affect drive operation.
A104 Comm Node Addr
Range:
1 to 247
Default:
1
See also:
d015
Sets the drive node address for the RS485 port if using a network
connection.
Important:
Power to the drive must be cycled before any changes
will affect drive operation.
A105 Comm Loss Action
Range:
0 = Fault
1 = Coast Stop
2 = Stop
3 = Continu Last
Default:
0 = Fault
See also:
d015, P037, A106
Selects the drive’s response to a loss of the communication
connection or excessive communication errors.
0 = Fault (Default): Drive will fault on an F81 Comm Loss and coast
to stop.
1 = Coast Stop: Stops the drive via coast to stop.
2 = Stop: Stops the drive via the setting in Stop Mode (P037).
3 = Continu Last: Drive continues operating at communication
commanded speed saved in RAM.
9-30
MD65 AC Drive User Manual
A106 Comm Loss Time
Range:
0.1 to 60.0 sec
Default:
5.0 sec
See also:
d015, A105
Sets the time that the drive will remain in communication loss before
implementing the option selected in Comm Loss Action (A105).
A107 Comm Format
Range:
0 = RTU 8-N-1
1 = RTU 8-E-1
2 = RTU 8-O-1
Default:
0 = RTU 8-N-1
See also:
N/A
Selects the protocol (RTU only), data bits (8 data bits only), parity
(None, Even, Odd), and stop bits (1 stop bit only) used by the
drive’s RS485 port.
Important:
Power to the drive must be cycled before any changes
will affect drive operation.
A108 Language
Range:
1 = English
2 = Francais
3 = Espanol
4 = Italiano
5 = Deutsch
6 = Reserved
7 = Portugues
8 = Reserved
9 = Reserved
10 = Nederlands
Default:
1 = English
See also:
N/A
Selects the language displayed by the remote communications
option.
Parameter Descriptions
9-31
A110 Anlg In 0-10V Lo
Range:
0.0 to 100.0%
Default:
0.0%
See also:
d020, P034, P038, A122
Sets the analog input level that corresponds to Minimum Freq
(P034) if a 0-10V input is used by Speed Reference (P038).
Setting this value larger than Anlg In 0-10V Hi (A111) inverts the
analog signal.
P035 [Maximum Freq]
ce
en
fer
e
dR
ee
Sp
P034 [Minimum Freq]
0
0
A110 [Anlg In 0-10V Lo]
A111 [Anlg In 0-10V Hi]
Figure 9.11 – Anlg In 0-10V Lo (A110)
A111 Anlg In 0-10V Hi
Range:
0.0 to 100.0%
Default:
100.0%
See also:
d020, P035, P038, A122, A123
Sets the analog input level that corresponds to Maximum Freq
(P035) if a 0-10 V input is used by Speed Reference (P038).
Setting this value smaller than Anlg In 0-10V Lo (A110) inverts the
analog signal.
A112 Anlg In4-20mA Lo
Range:
0.0 to 100.0%
Default:
0.0%
See also:
d021, P034, P038
Sets the analog input level that corresponds to Minimum Freq
(P034) if a 40-20 mA input is used by Speed Reference (P038).
Setting this value larger than Anlg In4-20mA Hi (A113) inverts the
analog signal.
9-32
MD65 AC Drive User Manual
A113 Anlg In4-20mA Hi
Range:
0.0 to 100.0%
Default:
100.0%
See also:
d021, P035, P038
Sets the analog input level that corresponds to Maximum Freq
(P035) if a 4-20 mA input is used by Speed Reference (P038).
Setting this parameter to a value less than Anlg In4-20mA Lo (A112)
inverts the analog signal.
A114 Slip Hertz @ FLA
Range:
0.0 to 10.0 Hz
Default:
2.0 Hz
See also:
P033
Enables compensation for the inherent slip in an induction motor.
This frequency is added to the commanded output frequency based
on motor current. If motor shaft speed decreases significantly under
heavy loads, then increase the value of this parameter. Setting this
parameter to 0.0 disables this function.
A118 Current Limit 2
Range:
0.1 to Drive Rated Amps x 1.8
Default:
Drive Rated Amps x 1.8
See also:
P033, A051-A054, A089
Maximum output current allowed before current limiting occurs. This
parameter is only active if Digital Inx Sel (A051-A054) is set to
25 = Current Lmt2 and is active.
A119 Skip Frequency
Range:
0 to 400 Hz
Default:
0 Hz
See also:
A120
Sets the center of a frequency band at which the drive will not
operate continuously (also called an avoidance frequency). A
setting of 0 disables this parameter.
Parameter Descriptions
9-33
A120 Skip Freq Band
Range:
0.0 to 30.0 Hz
Default:
0.0 Hz
See also:
A119
Determines the bandwidth around Skip Frequency (A119); half the
band above and half the band below the skip frequency. Refer to
figure 9.12.
A setting of 0 disables this parameter.
Frequency
Command
Frequency
Drive Output
Frequency
2x Skip
Frequency Band
Skip Frequency
Time
Figure 9.12 – Skip Freq Band (A120)
A121 Stall Fault Time
Range:
0 = 60 sec
1 = 120 sec
2 = 240 sec
3 = 360 sec
4 = 480 sec
5 = Flt Disabled
Default:
0 = 60 sec
See also:
A089-A118
Sets the time that the drive will remain in stall mode before a fault is
issued.
9-34
MD65 AC Drive User Manual
A122 Analog In Loss
Range:
0 = Disabled
1 = Fault (F29)
2 = Stop
3 = Zero Ref
4 = Min Freq Ref
5 = Max Freq Ref
6 = Int Freq Ref
Default:
0 = Disabled
See also:
A110, A111, A132
Selects the drive action when an input signal loss is detected.
Signal loss is defined as an analog signal less than 1 V or 2 mA.
The signal loss event ends and normal operation resumes when the
input signal level is greater than or equal to 1.5 V or 3 mA. If using a
0-10 V analog input, set Anlg In 0-10V Lo (A110) to a minimum of
20% (i.e., 2 V).
1 = Fault (F29): F29 Analog Input Loss.
2 = Stop: Uses Stop Mode (P037).
3 = Zero Ref: Drive runs at zero speed reference.
4 = Min Freq Ref: Drive runs at minimum frequency.
5 = Max Freq Ref: Drive runs at maximum frequency.
6 = Int Freq Ref: Drive runs at internal frequency.
A123 10V Bipolar Enbl
Range:
0 = Uni-Polar In (0 to 10 V only)
1 = Bi-Polar In (+/-10 V)
Default:
0 = Uni-Polar In
See also:
P038, A111
Enables/disables bipolar control. In bipolar mode, direction is
commanded by the sign of the reference.
Parameter Descriptions
9-35
A124 Var PWM Disable
Range:
0 = Enabled
1 = Disabled
Default:
0 = Enabled
See also:
A091
Enables/disables a feature that varies the carrier frequency for the
PWM output waveform defined by PWM Frequency (A091).
Disabling this feature when low frequency conditions exist may
result in IGBT stress and nuisance tripping.
A125 Torque Perf Mode
Range:
0 = V/Hz
1 = Sensrls Vect
Default:
1 = Sensrls Vect
See also:
A084, A085, A086, A087, A127
Enables/disables sensorless vector control operation.
A126 Motor NP FLA
Range:
0.1 to (Drive Rated Amps x 2)
Default:
Drive Rated Amps
See also:
A127
Set to the motor nameplate rated full load amps.
A127 Autotune
Range:
0 = Ready/Idle
1 = Static Tune
2 = Rotate Tune
Default:
0 = Ready/Idle
See also:
A125, A126, A128, A129
Provides an automatic method for setting IR Voltage Drop (A128)
and Flux Current Ref (A129), which affect sensorless vector
performance. Motor NP FLA (A126) must be set to the motor
nameplate full load amps before running the Autotune procedure.
If the Autotune procedure fails, an F80 SVC Autotune fault is
displayed.
0 = Ready/Idle: The parameter returns to this setting following a
Static Tune or Rotate Tune.
9-36
MD65 AC Drive User Manual
1 = Static Tune: A temporary command that initiates a
non-rotational motor stator resistance test for the best possible
automatic setting of IR Voltage Drop (A128). A start command is
required following the initiation of this setting. The parameter returns
to 0 = Ready/Idle following the test, at which time another start
transition is required to operate the drive in normal mode. Used
when the motor cannot be uncoupled from the load.
2 = Rotate Tune: A temporary command that initiates a Static Tune
followed by a rotational test for the best possible automatic setting
of Flux Current Ref (A129). A start command is required following
the initiation of this setting. The parameter returns to 0 = Ready/Idle
following the test, at which time another start transition is required to
operate the drive in normal mode.
Important:
!
Used when the motor is uncoupled from the load. The
results may not be valid if a load is coupled to the
motor during this procedure.
ATTENTION: Rotation of the motor in an undesired
direction can occur during this procedure. To guard
against possible injury and/or equipment damage, it
is recommended that the motor be disconnected
from the load before proceeding.
A128 IR Voltage Drop
Range:
0.0 to 230.0 VAC
Default:
Based on Drive Rating
See also:
A127
The value of volts dropped across the resistance of the motor stator.
A129 Flux Current Ref
Range:
0.00 to Motor NP Volts (P031)
Default:
Based on Drive Rating
See also:
A127
The value of amps for full motor flux.
Parameter Descriptions
9-37
A130 PID Trim Hi
Range:
0.0 to 400.0
Default:
0.0
See also:
N/A
Sets the maximum positive value that is added to a PID reference
when PID trim is used.
A131 PID Trim Lo
Range:
0.0 to 400.0
Default:
0.0
See also:
N/A
Sets the minimum positive value that is added to a PID reference
when PID trim is used.
A132 PID Ref Select
Range:
0 = PID Disabled
1 = PID Setpoint
2 = 0-10V Input
3 = 4-20mA Input
4 = Comm Port
5 = Setpnt, Trim
6 = 0-10V, Trim
7 = 4-20mA, Trim
8 = Comm, Trim
Default:
0 = PID Disabled
See also:
P038, A122
Enables/Disables PID mode and selects the source of the PID
reference.
A133 PID Feedback Sel
Range:
0 = 0-10V Input
1 = 4-20mA Input
2 = Comm Port
Default:
0 = 0-10V Input
See also:
N/A
Selects the source of the PID feedback.
When A133 = 0, the PID will not function with a bipolar input.
Negative voltages are treated as 0 volts.
9-38
MD65 AC Drive User Manual
A134 PID Prop Gain
Range:
0.00 to 99.99
Default:
0.00
See also:
N/A
Sets the value for the PID proportional component when the PID
mode is enabled by PID Ref Select (A132).
A135 PID Integ Time
Range:
0.0 to 999.9 sec
Default:
0.0 sec
See also:
N/A
Sets the value for the PID integral component when the PID mode
is enabled by PID Ref Select (A132).
A136 PID Diff Rate
Range:
0.00 to 99.99 (1/sec)
Default:
0.00 (1/sec)
See also:
N/A
Sets the value for the PID differential component when the PID
mode is enabled by PID Ref Select (A132).
A137 PID Setpoint
Range:
0.0 to 100.0%
Default:
0.0%
See also:
N/A
Provides an internal fixed value for the process setpoint when the
PID mode is enabled by PID Ref Select (A132).
A138 PID Deadband
Range:
0.0 to 10.0%
Default:
0.0%
See also:
N/A
Sets the lower limit of the PID output.
Parameter Descriptions
9-39
A139 PID Preload
Range:
0.0 to 400.0 Hz
Default:
0.0 Hz
See also:
N/A
Sets the value used to preload the integral component on start or
enable.
A140
A141
A142
A143
A144
A145
A146
A147
Stp Logic 0
Stp Logic 1
Stp Logic 2
Stp Logic 3
Stp Logic 4
Stp Logic 5
Stp Logic 6
Stp Logic 7
Range:
0001 to bAFF
Default:
00F1
See also:
P038, P039, Po40, A051-A054, A055, A058, A061,
A067, A068, A070-A077, A150-A157
Parameters A140-A147 can be used to create a custom profile of
frequency commands. Each “step” can be based on time, status of
a logic input, or a combination of time and the status of a logic input.
These parameters are only active if Speed Reference (P038) is set
to 6 = Stp Logic.
Digits 0-3 for each parameter (Stp Logic x) must be programmed
according to the desired profile. A logic input is established by
setting a digital input, Digital Inx Sel (A051-A054), to 23 = Logic In1
and or 24 = Logic In2.
A time interval between steps can be programmed using Stp Logic
Time x (A150-A157). See table 9.6 for related parameters.
The speed for any step is programmed using Preset Freq x
(A070-A077).
Table 9.6 – Related Parameters for Stp Logic Parameters (A140-A147)
Step Logic Parameter
(Active when P038 = 6 “Stp Logic”)
9-40
Related Preset Frequency Parameter Related Step Logic Time Parameter
(Can be activated independent of (Active when A140-A147 Digit 0 or 1
Step Logic Parameters)
are set to 1, b, C, d or E)
A140 (Stp Logic 0)
A070 (Preset Freq 0)
A150 (Stp Logic Time 0)
A141 (Stp Logic 1)
A071 (Preset Freq 1)
A151 (Stp Logic Time 1)
A142 (Stp Logic 2)
A072 (Preset Freq 2)
A152 (Stp Logic Time 2)
A143 (Stp Logic 3)
A073 (Preset Freq 3)
A153 (Stp Logic Time 3)
A144 (Stp Logic 4)
A074 (Preset Freq 4)
A154 (Stp Logic Time 4)
MD65 AC Drive User Manual
Table 9.6 – Related Parameters for Stp Logic Parameters (A140-A147) (Continued)
Step Logic Parameter
(Active when P038 = 6 “Stp Logic”)
Related Preset Frequency Parameter Related Step Logic Time Parameter
(Can be activated independent of (Active when A140-A147 Digit 0 or 1
Step Logic Parameters)
are set to 1, b, C, d or E)
A145 (Stp Logic 5)
A075 (Preset Freq 5)
A155 (Stp Logic Time 5)
A146 (Stp Logic 6)
A076 (Preset Freq 6)
A156 (Stp Logic Time 6)
A147 (Stp Logic 7)
A077 (Preset Freq 7)
A157 (Stp Logic Time 7)
How Step Logic Works
The step logic sequence begins with a valid start command. A
normal sequence always begins with Stp Logic 0 (A140).
Digit 0: Logic For Next Step
This digit defines the logic for the next step. When the condition is
met, the program advances to the next step. Step 0 follows Step 7.
Example: Digit 0 is set 3. When “Logic In2” becomes active, the
program advances to the next step.
Digit 1: Logic to Jump to a Different Step
For all settings other than F, when the condition is met, the program
overrides Digit 0 and jumps to the step defined by digit 2.
Digit 2: Different Step to Jump
When the condition for digit 1 is met, the digit 2 setting determines
the next step or to end the program.
Digit 3: Step Settings
This digit defines what accel/decel profile the speed command will
follow and the direction of the command for the current step. In
addition, if a relay or opto output (parameters A055, A058, and
A061) is set to 15 = StpLogic Out, this parameter can control the
status of that output.
Any Step Logic parameter can be programmed to control a relay or
opto output, but you cannot control different outputs based on the
condition of different Step Logic commands.
Step Logic Settings
The logic for each function is determined by the four digits for each
step logic parameter. Figure 9.13 shows the available settings for
each digit.
Parameter Descriptions
9-41
Logic For Next Step
Logic to Jump to a Different Step
Different Step to Jump
Step Settings
Digit 3 Settings
Required
Setting
0
1
2
3
4
5
6
7
8
9
A
b
Accel/Decel
Param. Used
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 1
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Accel/Decel 2
Step Logic
Output State
Off
Off
Off
On
On
On
Off
Off
Off
On
On
On
Digit 2 Settings
0 = Jump to Step 0
1 = Jump to Step 1
2 = Jump to Step 2
3 = Jump to Step 3
4 = Jump to Step 4
5 = Jump to Step 5
6 = Jump to Step 6
7 = Jump to Step 7
8 = End Program (Normal Stop)
9 = End Program (Coast to Stop)
A = End Program and Fault (F2)
Digit 0
Digit 1
Digit 2
Digit 3
Commanded
Direction
FWD
REV
No Output
FWD
REV
No Output
FWD
REV
No Output
FWD
REV
No Output
Digit 1 and Digit 0 Settings
0 = Skip Step (Jump Immediately)
1 = Step Based on (Stp Logic Time x)
2 = Step if “Logic In1” is Active
3 = Step if “Logic In2” is Active
4 = Step if “Logic In1” is Not Active
5 = Step if “Logic In2” is Not Active
6 = Step if either “Logic In1” or “Logic In2” is Active
7 = Step if both “Logic In1” and “Logic In2” is Active
8 = Step if neither “Logic In1” or “Logic In2” is Active
9 = Step if “Logic In1” is Active and “Logic In2” is Not Active
A = Step if “Logic In2” is Active and “Logic In1” is Not Active
b = Step after (Stp Logic Time x) and “Logic In1” is Active
C = Step after (Stp Logic Time x) and “Logic In2” is Active
d = Step after (Stp Logic Time x) and “Logic In1” is Not Active
E = Step after (Stp Logic Time x) and “Logic In2” is Not Active
F = Do Not Step/Ignore Digit 2 Settings
Figure 9.13 – Digit Settings
A150
A151
A152
A153
A154
A155
A156
A157
Stp Logic Time 0
Stp Logic Time 1
Stp Logic Time 2
Stp Logic Time 3
Stp Logic Time 4
Stp Logic Time 5
Stp Logic Time 6
Stp Logic Time 7
Range:
0.0 to 999.9 sec
Default:
30.0 sec
See also:
P038, A055, A058, A061, A070-A077, A140-A147
Sets the time to remain in each step if the corresponding StpLogic
command word is set to “Step after Time.”
9-42
MD65 AC Drive User Manual
9.3
Display Group Parameters
d001 Output Freq
Range:
0.0 to Maximum Freq (P035)
Default:
Read Only
See also:
d002, d010, P034, P035, P038
Displays the output frequency present at terminals T1, T2, and T3
(U, V, and W).
d002 Commanded Freq
Range:
0.0 to Maximum Freq (P035)
Default:
Read Only
See also:
d001, d013, P034, P035, P038
Displays the value of the active frequency command. The
commanded frequency is displayed even if the drive is not running.
Important:
The frequency command can come from a number of
sources. Refer to section 6.6, Start and Speed
Reference Control, for more information.
d003 Output Current
Range:
0.00 to (Drive Rated Amps x 2)
Default:
Read Only
See also:
N/A
Displays the output current present at terminals T1, T2, and T3 (U,
V, and W).
d004 Output Voltage
Range:
0 to Drive Rated Volts
Default:
Read Only
See also:
P031, A084, A088
Displays the output voltage present at terminals T1, T2, and T3 (U,
V, and W).
Parameter Descriptions
9-43
d005 DC Bus Voltage
Range:
Based on Drive Rating
Default:
Read Only
See also:
N/A
Displays the present DC bus voltage level.
d006 Drive Status
Range:
0 = Condition False
1 = Condition True
See figure 9.14
Default:
Read Only
See also:
A095
Displays the present operating status of the drive.
Running
Forward
Accelerating
Decelerating
Bit 0
Bit 1
Bit 2
Bit 3
Figure 9.14 – Drive Status (d006) Bit Definitions
d007 Fault 1 Code
d008 Fault 2 Code
d009 Fault 3 Code
Range:
F2 to F122
Default:
Read Only
See also:
N/A
Displays a code that represents a drive fault. The codes will appear
in these parameters in the order they occur (that is, Fault 1 Code in
d007 will contain the more recent fault). Repetitive faults will be
recorded only once. Refer to chapter 10 for the fault code
descriptions.
9-44
MD65 AC Drive User Manual
d010 Process Display
32
Range:
0.00 to 9999
Default:
Read Only
See also:
d001, A099
Displays the output frequency scaled by Process Factor (A099).
Output Frequency x Process Factor = Process Display
d012 Control Source
Range:
0 to 9
See figure 9.15.
Default:
Read Only
See also:
P036, P038, A051-A054
Displays the active source of the Start Command and Speed
Command, which are normally defined by the settings of Start
Source (P036) and Speed Reference (P038) but may be overridden
by digital inputs. Refer to the flowcharts in sections 6.6 and 6.7 for
details.
Start Command
Digit 0
0 = Keypad
1 = 3-Wire
2 = 2-Wire
3 = 2-Wire Level Sensitive
4 = 2-Wire High Speed
5 = RS485 Port
9 = Jog
Speed Command
Digit 1
0 = Drive Potentiometer
1 = Internal Freq (A069)
2 = 0-10 V Input/Remote Potentiometer
3 = 4-20 mA Input
4 = Preset Freq x (A070-A077)
Digital Inx Sel (A051-A050) must be set to 4
5 = RS485 Port
6 = Step Logic Control (A140-A147)
9 = Jog Freq
Reserved
Digit 2
Reserved
Digit 3
Figure 9.15 – Control Source (d012) Bit Definitions
Parameter Descriptions
9-45
d013 Contrl In Status
Range:
0 = Input Present
1 = Input Not Present
See figure 9.16
Default:
Read Only
See also:
d002, P034, P035
Displays the status of the control terminal block control inputs.
Important:
Actual control commands may come from a source
other than the control terminal block.
1 = Input Present, 0 = Input Not Present
Start / Run FWD Input (I/O Terminal 02)
Bit 0
Direction / Run REV Input (I/O Terminal 03)
Bit 1
Stop Input1 (I/O Terminal 01)
Bit 2
Dynamic Brake Transistor On
Bit 3
1
The stop input must be present in order to start the drive.
When this bit is a 1, the drive can be started.
When this bit is a 0, the drive will stop.
Figure 9.16 – Contrl In Status (d013) Bit Definitions
d014 Dig In Status
Range:
0 = Input Not Present
1 = Input Present
See figure 9.17.
Default:
Read Only
See also:
A051-A054
Displays the status of the control terminal block digital inputs.
Digital In1 Sel (I/O Terminal 05)
Digital In2 Sel (I/O Terminal 06)
Digital In3 Sel (I/O Terminal 07)
Digital In4 Sel (I/O Terminal 08)
Bit 0
Bit 1
Bit 2
Bit 3
Figure 9.17 – Dig In Status (d014) Bit Definitions
9-46
MD65 AC Drive User Manual
d015 Comm Status
Range:
0 = Condition False
1 = Condition True
See figure 9.18.
Default:
Read Only
See also:
A103 through A107
Displays the status of the communications ports.
Receiving Data
Transmitting Data
RS485 Option Connected
Communication Error Occurred
Bit 0
Bit 1
Bit 2
Bit 3
Figure 9.18 – Comm Status (d015) Bit Definitions
d016 Control SW Ver
Range:
1.00 to 99.99
Default:
Read Only
See also:
N/A
Displays the Main Control Board software version.
d017 Drive Type
Range:
1001 to 9999
Default:
Read Only
See also:
N/A
Used by Rockwell Automation field service personnel.
d018 Elapsed Run Time
Range:
0 to 9999 Hours
Default:
Read Only
See also:
N/A
Displays the accumulated time drive is outputting power. The time is
displayed in 10-hour increments (that is, 1 = 10 hours).
Parameter Descriptions
9-47
d019 Testpoint Data
Range:
0 to FFFF
Default:
Read Only
See also:
A102
Displays the present value of the function selected in Testpoint
Select (A102).
d020 Analog In 0-10V
Range:
0.0 to 100.0%
Default:
Read Only
See also:
A110, A111
Displays the present value of the voltage at I/O Terminal 13
(100.0% = 10 V).
d021 Analog In 4-20mA
Range:
0.0 to 100.0%
Default:
Read Only
See also:
A112, A113
Displays the present value of the current at I/O Terminal 15
(0.0% = 4 mA, 100.0% = 20 mA).
d022 Output Power
Range:
0.00 to (Drive Rated Power x 2)
Default:
Read Only
See also:
N/A
Displays the output power present at T1, T2, and T3, (U, V, and W).
d023 Output Powr Fctr
Range:
0.0 to 180.0 deg
Default:
Read Only
See also:
N/A
Displays the angle in electrical degrees between motor voltage and
motor current.
9-48
MD65 AC Drive User Manual
d024 Drive Temp
Range:
0 to 120 degree C
Default:
Read Only
See also:
N/A
Displays the present operating temperature of the drive power
section.
d025 Counter Status
Range:
0 to 9999
Default:
Read Only
See also:
N/A
Displays the current value of the counter when the counter is
enabled.
d026 Timer Status
32
Range:
0.0 to 9999 seconds
Default:
Read Only
See also:
N/A
Displays the current value of the timer when the timer is enabled.
d028 Stp Logic Status
Range:
0 to 7
Default:
Read Only
See also:
N/A
When Speed Reference (P038) is set to 6 = Stp Logic, this
parameter displays the current step of the step logic profile as
defined by parameters Stp Logic x (A140-A147).
Parameter Descriptions
9-49
9-50
MD65 AC Drive User Manual
CHAPTER 10
Troubleshooting the Drive
ATTENTION: The drive contains high voltage capacitors that
take time to discharge after removal of mains supply. Before
working on the drive, ensure isolation of mains supply from
line inputs [R, S, T (L1, L2, L3)]. Wait three (3) minutes for
capacitors to discharge to safe voltage levels. Darkened
display LEDs is not an indication that capacitors have
discharged to safe voltage levels. Failure to observe this
precaution could result in severe bodily injury or loss of life.
!
ATTENTION: Only qualified electrical personnel familiar with
the construction and operation of this equipment and the
hazards involved should install, adjust, operate, or service this
equipment. Read and understand this manual and other
applicable manuals in their entirety before proceeding. Failure
to observe this precaution could result in severe bodily injury
or loss of life.
The MD65 constantly monitors its status and provides the following
ways to determine the status of the drive and to troubleshoot
problems that may occur:
•
LEDs on the drive (refer to figure 8.1 and table 8.1 for a
description of the LEDs)
•
Fault codes
10.1 Fault Codes
Faults codes indicate conditions within the drive that require
immediate attention. The drive responds to a fault by initiating a
coast-to-stop sequence and turning off output power to the motor.
The integral keypad provides visual notification of a fault condition
by displaying the following:
•
Flashing fault number (code) on the display. (See table 10.1 for
the fault code descriptions.)
•
Flashing FAULT LED
In addition, parameters d007-d009 act as a fault log. See the
parameter descriptions in chapter 9 for more information.
Troubleshooting the Drive
10-1
10.1.1 Manually Clearing Faults
Step 1.
Note the number of the fault code flashing on the display.
Step 2.
Address the condition that caused the fault. Refer to table
10.1 for a description of the fault and corrective actions.
The cause must be corrected before the fault can be
cleared.
Step 3.
After corrective action has been taken, clear the fault and
reset the drive using one of the following methods:
• Press
if P037 (Stop Mode) is set to a value
between 0 and 3.
• Cycle drive power.
• Set A100 (Fault Clear) to 1.
• Cycle digital input if A051-A054 (Digital Inx Sel) is set
to 7 = Clear Fault.
10.1.2 Automatically Clearing Faults (Auto Restart
Feature)
The Auto Restart feature provides the ability for the drive to
automatically perform a fault reset followed by a start attempt
without user or application intervention. This allows remote or
“unattended” operation. This feature can only be used for autoresettable faults (see table 10.1).
When this type of fault occurs, and Auto Rstrt Tries (A092) is set to
a value greater than 0, a user-configurable timer, Auto Rstrt Delay
(A093), begins. When the timer reaches zero, the drive attempts to
automatically reset the fault. If the condition that caused the fault is
no longer present, the fault will be reset and the drive will be
restarted.
To automatically clear an auto-resettable fault and restart the
drive:
Step 1.
Set A092 (Auto Rstrt Tries) to a value other than 0.
Step 2.
Set A093 (Auto Rstrt Delay) to a value other than 0.
To automatically clear an OverVoltage, UnderVoltage, or
Heatsink OverTemp fault without restarting the drive:
Step 1.
Set A092 (Auto Rstrt Tries) to a value other than 0.
Step 2.
Set A093 (Auto Rstrt Delay) to 0.
Use caution when enabling this feature since the drive will attempt
to issue its own start command based on user-selected
programming.
10-2
MD65 AC Drive User Manual
No.
Fault
F2
Auxiliary
Input
Auto-Reset1?
Table 10.1 – Fault Descriptions and Corrective Actions
Description
Y Auxiliary input interlock
is open.
F3
Power Loss
F4
UnderVoltage Y DC bus voltage fell
below the minimum
value.
OverVoltage Y DC bus voltage
exceeded maximum
value.
F5
N DC bus voltage
remained below 85%
of nominal.
F6
Motor Stalled Y Drive is unable to
accelerate motor.
F7
Motor
Overload
Y Internal electronic
overload trip.
Action
•
•
•
Verify communications
programming for
intentional fault.
Monitor the incoming
AC line for low voltage
or line power
interruption.
• Check input fuses.
Monitor the incoming AC
line for low voltage or line
power interruption.
Monitor the AC line for
high line voltage or
transient conditions. Bus
overvoltage can also be
caused by motor
regeneration. Extend the
decel time or install
dynamic brake option.
Increase Accel Time x
(P039, A067) or reduce
load so drive output
current does not exceed
the current set by
parameter A089 (Current
Limit 1).
• An excessive motor load
exists. Reduce load so
drive output current
does not exceed the
current set by parameter
P033 (Motor OL
Current).
•
Troubleshooting the Drive
Check remote wiring.
Verify Boost Select
(A084) setting.
10-3
No.
Fault
F8
Heatsink
OverTemp
Auto-Reset1?
Table 10.1 – Fault Descriptions and Corrective Actions (Continued)
Description
Y Heatsink temperature
exceeds a predefined
value.
F12
HW
OverCurrent
F13
Ground Fault N
F29
Analog Input
Loss
Y
F33
Auto Rstrt
Tries
N
F38
Phase U to
Gnd
Phase V to
Gnd
Phase W to
Gnd
N
F39
F40
10-4
•
Action
Check for blocked or
dirty heat sink fins.
Verify that ambient
temperature has not
exceeded 40° C (104°F)
for IP 30/NEMA 1/UL
Type 1 installations or 50°C
(122°F) for Open type
installations.
• Check fan.
Check programming.
Check for excess load,
improper Boost Select
(A084) setting, DC brake
volts set too high, or other
causes of excess current.
A current path to earth Check the motor and
ground has been
external wiring to the drive
detected at one or
output terminals for a
more of the drive
grounded condition.
output terminals.
An analog input is
• Check parameters.
configured to fault on
• Check for broken/loose
signal loss. A signal
connections at inputs.
loss has occurred.
Configure with Analog
In Loss (A122).
Drive unsuccessfully
Correct the cause of the
attempted to reset a
fault and manually clear.
fault and resume
running for the
programmed number
of Auto Rstrt Tries
(A092).
A phase to ground fault • Check the wiring
between the drive and
has been detected
motor.
between the drive and
motor in this phase.
• Check motor for
grounded phase.
• Replace drive if fault
cannot be cleared.
N The drive output
current has exceeded
the hardware current
limit.
MD65 AC Drive User Manual
No.
Fault
F41 Phase UV
Short
F42 Phase UW
Short
F43 Phase VW
Short
F48 Params
Defaulted
F63
SW
OverCurrent
F64
Drive
Overload
F70
Power Unit
F80
SVC
Autotune
F81
Comm Loss
Auto-Reset1?
Table 10.1 – Fault Descriptions and Corrective Actions (Continued)
Description
N Excessive current has
been detected
between these two
output terminals.
•
•
N The drive was
commanded to write
default values to
EEPROM.
Y Programmed SW
Current Trip (A098)
has been exceeded.
N Drive rating of 150%
for 1 minute or 200%
for 3 seconds has been
exceeded.
N Failure has been
detected in the drive
power section.
Action
Check the motor and
drive output terminal
wiring for a shorted
condition.
Replace drive if fault
cannot be cleared.
•
Clear the fault or cycle
power to the drive.
• Program the drive
parameters as needed.
Check load requirements
and SW Current Trip
(A098) setting.
Reduce load or extend
Accel Time.
•
•
Cycle power.
•
•
Check connection.
•
Turn off using Comm
Loss Action (A105).
Replace drive if fault
cannot be cleared.
N The Autotune function Restart procedure.
was either cancelled
by the user or failed.
• If module was not
N RS485 port stopped
intentionally
communicating.
disconnected, check
wiring to the port.
Replace wiring, port
expander, module, or
complete drive as
required.
Troubleshooting the Drive
A module was
intentionally
disconnected.
10-5
No.
Fault
F100 Parameter
Checksum
Auto-Reset1?
Table 10.1 – Fault Descriptions and Corrective Actions (Continued)
Description
Action
N The checksum read
Set Reset to Defalts
from the board does
(P041) to 1 = Reset
not match the
Defaults.
checksum calculated.
F122 I/O Board Fail N Failure has been
• Cycle power.
detected in the drive
control and I/O section. • Replace drive if fault
cannot be cleared.
1
Refer to section 10.1.2 for information about the Auto Restart Feature.
10-6
MD65 AC Drive User Manual
10.2 Troubleshooting Tables
Use the following tables to troubleshoot the drive. If you cannot
resolve the problem using these tables, contact Reliance Electric.
10.2.1 Problem: Drive Does Not Start From Terminal
Block Start or Run Inputs
Table 10.2 – Problem: Drive Does Not Start From Terminal Block Start or Run Inputs
Possible Cause(s)
Drive is faulted
Indication
Flashing red
FAULT LED
Corrective Action
Clear fault by using one of
the following methods:
•
•
•
Incorrect programming.
None
• Start Source (P036) is set
to 0 = Keypad or
5 = RS485 Port.
• Digital Inx Sel (A051-A054
is set to 5 = Local and the
input is active.
None
Incorrect input wiring. See
section 6.4.1 for wiring
examples.
• 2-wire control requires
Run Forward, Run
Reverse or Jog input.
• 3-wire control requires
Start and Stop inputs
• Stop input is always
required.
Incorrect Sink/Source DIP
None
switch setting.
Troubleshooting the Drive
Press Stop
Cycle power
Set Fault Clear (A100) to
1 = Clear Faults
• Cycle digital input if
Digital Inx Sel (A051A054) is set to 7 = Clear
Fault
Check parameter settings.
Wire inputs correctly and/or
install jumper.
Set switch to match wiring
scheme.
10-7
10.2.2 Problem: Drive Does Not Start From Integral
Keypad
Table 10.3 – Problem: Drive Does Not Start From Integral Keypad
Cause(s)
Integral keypad is not
enabled.
Indication
Start Key
Status LED is
not on.
I/O Terminal 01 “Stop” input
is not present.
None
Corrective Action
Set Start Source (P036)
to 0 = Keypad.
• Set Digital Inx Sel (A051
to A054) to 5 = Local and
activate the input.
Wire inputs correctly and/or
install jumper.
•
10.2.3 Problem: Drive Does Not Respond to Changes
in Speed Command
Table 10.4 – Problem: Drive Does Not Respond to Changes in Speed Command
Cause(s)
No value is coming from
the source of the
command.
Indication
The RUN
LED is on and
output is 0
Hz.
•
•
•
Incorrect reference source None
is being selected via
remote device or digital
inputs.
•
•
•
•
10-8
Corrective Action
Check Control Source (d012)
for correct source.
If the source is an analog
input, check wiring and use a
meter to check for presence of
signal.
Check Commanded
Frequency (d002) to verify
correct command.
Check Control Source (d012)
for correct source.
Check Digital Input Status
(d014) to see if inputs are
selecting an alternate source.
Verify settings for Digital Inx
Sel (A051-A054).
Check Speed Reference
(P038) for the source of the
speed reference. Reprogram
as necessary.
Review the Speed Reference
Control chart in figure 6.2.
MD65 AC Drive User Manual
10.2.4 Problem: Motor Does Not Start
Cause(s)
No output voltage to the
motor.
Indication
None
Corrective Action
Check the power circuit.
• Check the supply voltage.
• Check all the fuses and
disconnects.
Check the motor.
• Verify that the motor is
connected properly.
Drive is faulted.
Troubleshooting the Drive
Flashing red
STATUS LED.
Check the control input
signals
• Verify that a Start signal is
present. If 2-Wire control
is used, verify that either
the Run Forward or Run
Reverse signal is active,
but not both.
• Verify that I/O Terminal 01
is active.
• Verify that Start Source
(P036) matches your
configuration.
• Verify that Reverse
Disable (A095) is not
prohibiting movement.
Clear fault.
•
•
•
Press Stop
•
Cycle digital input if Digital
Inx Sel (A051-A054) is set
to 7 = Clear Fault.
Cycle power
Set Fault Clear (A100) to
1 = Clear Faults.
10-9
10.2.5 Problem: Motor and/or Drive Will Not
Accelerate to Commanded Speed
Table 10.5 – Problem: Motor and/or Drive Will Not Accelerate to Commanded Speed
Cause(s)
Indication
Acceleration time is
None
excessive.
Excess load or short
None
acceleration times force the
drive into current limit,
slowing or stopping
acceleration.
Speed command source or None
value is not as expected.
Corrective Action
Reprogram P039 (Accel Time
1) or A067 (Accel Time 2).
•
Compare Output Current
(d003) with Current Limit
(A089).
•
Remove excess load or
reprogram Accel Time 1
(P039) or Accel Time 2
(A067).
•
Check for improper Boost
Select (A084) setting.
•
Verify Commanded Freq
(d002).
•
Programming is preventing None
the drive output from
exceeding limiting values.
Torque performance does None
not match motor
characteristics.
Check Control Source
(d012) for the proper Speed
Command.
Check Maximum Freq (P035)
to ensure that speed is not
limited by programming.
• Set motor nameplate full
load amps in Motor NP FLA
(A126).
• Perform Autotune
procedure (A127 = Static
Tune or Rotate Tune).
• Set Torque Perf Mode
(A125) to 0 = V/Hz.
10.2.6 Problem: Motor Operation is Unstable
Table 10.6 – Problem: Motor Operation is Unstable
Cause(s)
Motor data was incorrectly
entered.
10-10
Indication
None
Corrective Action
1. Correctly enter motor
nameplate data into P031,
P032, and P033.
2. Enable Compensation
(A097).
3. Use Boost Select (A084) to
reduce boost level.
MD65 AC Drive User Manual
10.2.7 Problem: Drive Will Not Reverse Motor
Direction.
Table 10.7 – Problem: Drive Will Not Reverse Motor Direction
Cause(s)
Indication
Digital input is not selected None
for reversing control.
Digital input is incorrectly
wired.
Motor wiring is improperly
phased for reverse.
Reverse is disabled.
None
Corrective Action
Check Digital Inx Sel. Choose
correct input and program for
reversing mode.
Check input wiring.
None
Switch two motor leads.
None
Check Reverse Disable
(A095).
10.2.8 Problem: Drive Does Not Power Up
Cause(s)
No input power to the drive.
Indication
None
Jumper between I/O
Terminals P2 and P1 not
installed and/or DC Bus
Inductor not connected.
None
Troubleshooting the Drive
Corrective Action
Check the power circuit.
• Check the supply voltage.
• Check all fuses and
disconnects.
Install jumper or connect DC
Bus Inductor.
10-11
10-12
MD65 AC Drive User Manual
APPENDIX A
Technical Specifications
Environment
Altitude:
1000 m (3300 ft) maximum without derating
Ambient Operating
Temperature:
Open Type, IP 20: -10° C (14° F) to 50° C (122° F)
NEMA 1, IP30, UL Type 1: -10° C (14° F) to 40° C
(104° F)
Storage
Temperature (all
const.):
-40° C (-40° F) to 85° C (185° F)
Cooling Method:
0.5 HP drives: Convection
1 HP and above: Fan
Relative Humidity:
0% to 95%, non-condensing
Atmosphere:
Important: The drive must not be installed in an area
where the ambient atmosphere contains volatile or
corrosive gas, vapors, or dust. If the drive is not going
to be installed for a period of time, it must be stored in
an area where it will not be exposed to a corrosive
atmosphere.
Shock (Operating):
15 G peak for 11 ms duration (+/-1.0 ms)
Vibration
(Operating):
1 G peak, 5 to 2000 Hz
Control
Carrier Frequency:
2-16 kHz. Drive rating based on 4 kHz.
Frequency Accuracy • Digital Input: Within +/-0.05% of set output
frequency.
• Analog Input: Within 0.5% of maximum output
frequency. 10-bit resolution.
• Analog Output: +/-2% of full scale. 10-bit resolution.
Speed Regulation - +/-1% of base speed across a 60:1 speed range.
Open Loop with Slip
Compensation:
Stop Modes:
Technical Specifications
Multiple programmable stop modes including: Ramp,
Coast, DC-Brake, Ramp-to-Hold, S Curve, and
Dynamic Braking (1 HP and above)..
A-1
Accel/Decel:
Two independently programmable accel and decel
times. Each time may be programmed from 0-600
seconds in 0.1 second increments.
Intermittent
Overload:
• 150% Overload capability for up to 1 minute.
• 200% Overload capacity for up to 3 seconds
Electronic Motor
Class 10 protection with speed-sensitive response.
Overload Protection:
Input/Output Rating
Output Frequency:
0-400 Hz (Programmable)
Efficiency:
97.5% (Typical)
Digital Control Inputs (Inputs Current = 6 mA)
SRC (Source)
Mode:
18-24 V = ON
0-6 V = OFF
SNK (Sink) Mode:
0-6 V = ON
18-24 V = OFF
Analog Control Inputs
4-20 mA Analog:
250 ohm input impedance
0-10 V DC Analog:
100k ohm input impedance
External Pot:
1-10 k ohm, 2 Watt minimum
Control Output
Programmable Output (form C relay)
Resistive Rating:
3.0 A at 30 V DC, 3.0 A at 125 V AC, 3.0 A at
240 V AC
Inductive Rating:
0.5 A at 30 V DC, 0.5 A at 125 V AC, 0.5 A
Opto Outputs
Resistive Rating:
30 V DC, 50 mA
Inductive Rating:
Recover diode. Refer to figure 6.1 for details.
Analog Outputs (10-bit)
Rating:
0-10 V, 1k ohm min.
4-20 mA, 525 ohm max
Fuses and Circuit Breakers
Recommended
Fuse Type:
UL Class J, CC, T or Type BS88; 600 V (550 V) or
equivalent.
Recommended
Circuit Breakers:
HMCP circuit breakers or equivalent.
A-2
MD65 AC Drive User Manual
Protective Features
Motor Protection:
Programmable I2t overload protection provides Class
10 protection. See parameter P033.
Overcurrent:
200% hardware limit, 300% instantaneous fault
Over Voltage:
• 100-120 V AC Input – Trip occurs at 405 V DC bus
voltage (equivalent to 150 V AC incoming line
• 200-240 V AC Input – Trip occurs at 405 V DC bus
voltage (equivalent to 290 V AC incoming line)
• 380-460 V AC Input – Trip occurs at 810 V DC bus
voltage (equivalent to 575 V AC incoming line)
Under Voltage:
• 100-120 V AC Input – Trip occurs at 210 V DC bus
voltage (equivalent to 75 V AC incoming line)
• 200-240 V AC Input – Trip occurs at 210 V DC bus
voltage (equivalent to 150 V AC incoming line
• 380-480 V AC Input – Trip occurs at 390 V DC bus
voltage (equivalent to 275 V AC incoming line)
Control RideThrough:
Minimum ride-through is 0.5 sec - typical value 2 sec
Faultless Power
Ride-Through:
100 milliseconds
Dynamic Braking
Internal brake IGBT included with all ratings 0.75 kW (1 HP) and larger.
Approvals
LIST
ED 966X
UL
®
I ND
CO N T E Q
LIST
UL508C
C
ED 966X
UL
®
I ND
CSA 22.2
CO N T E Q
EMC Directive 89/336
LV:
EN 50178, EN 60204
EMC: EN 61800-3, EN 50081-1, EN 50082-2
Technical Specifications
A-3
A-4
MD65 AC Drive User Manual
APPENDIX B
Record of
User Settings
B.1 Basic Parameter Group
No.
Parameter Name
Default
Value
Page
No.
P031 Motor NP Volts
Varies
9-2
P032 Motor NP Hertz
60 Hz
9-2
P033 Motor OL Current
Varies
9-2
P034 Minimum Freq
0.0 Hz
9-2
P035 Maximum Freq
60 Hz
9-2
P036 Start Source
0 = Keypad
9-3
P037 Stop Mode
1 = Coast, CF
9-4
P038 Speed Reference
0 = Drive Pot
9-5
P039 Accel Time 1
5.0 sec
9-6
P040 Decel Time 1
5.0 sec
9-6
P041 Reset to Defalts
0 = Read/Idle
9-7
Record of User Settings
User Setting
B-1
B.2 Advanced Parameter Group
Default
Value
Page
No.
A051 Digital In1 Sel
4 = Preset Freq
9-8
A052 Digital In2 Sel
4 = Preset Freq
9-8
A053 Digital In3 Sel
4 = Preset Freq
9-8
A054 Digital In4 Sel
5 = Local
9-8
A055 Relay Out Sel
0 = Ready/Fault
9-11
A056 Relay Out Level
0.0
9-13
A058 Opto Out1 Sel
0 = Ready/Fault
9-14
A059 Opto Out1 Level
0.0
9-16
A061 Opto Out2 Sel
2 = Motor
Running
9-14
A062 Opto Out2 Level
0.0
9-16
A064 Opto Out Logic
0
9-16
A065 Analog Out Sel
0
9-17
A066 Analog Out High
100%
9-17
A067 Accel Time 2
10.0 sec
9-18
A068 Decel Time 2
10.0 sec
9-18
A069 Internal Freq
0.0 Hz
9-19
A070 Preset Freq 0
0.0 Hz
9-20
A071 Preset Freq 1
0.0 Hz
9-20
A072 Preset Freq 2
0.0 Hz
9-20
A073 Preset Freq 3
0.0 Hz
9-20
A074 Preset Freq 4
0.0 Hz
9-20
A075 Preset Freq 5
0.0 Hz
9-20
A076 Preset Freq 6
0.0 Hz
9-20
A077 Preset Freq 7
0.0 Hz
9-20
A078 Jog Frequency
10.0 Hz
9-20
A079 Jog Accel/Decel
10.0 sec
9-21
A080 DC Brake Time
0.0 sec
9-21
A081 DC Brake Level
Drive Rated
Amps x 0.5
9-21
A082 DB Resistor Sel
0 = Disabled
9-22
A083 S Curve%
0% (Disabled)
9-22
No.
B-2
Parameter Name
User Setting
MD65 AC Drive User Manual
Default
Value
Page
No.
A084 Boost Select
8 = 5.0, CT
7 = 2.5, CT (for
5.0, 7.5, and
10.0 HP drives
only)
9-23
A085 Start Boost
5.0%
9-24
A086 Break Voltage
25.0%
9-24
A087 Break Frequency
15.0 Hz
9-25
A088 Maximum Voltage
Drive Rated
Volts
9-25
A089 Current Limit 1
Drive Rated
Amps x 1.8
9-25
A090 Motor OL Select
0 = No Derate
9-25
A091 PWM Frequency
4.0 kHz
9-26
A092 Auto Rstrt Tries
0
9-26
A093 Auto Rstrt Delay
1.0 sec
9-27
A094 Start At PowerUp
0 = Disabled
9-27
A095 Reverse Disable
0 = Rev Enabled
9-27
A096 Flying Start En
0 = Disabled
9-28
A097 Compensation
1 = Electrical
9-28
A098 SW Current Trip
0.0 (Disabled)
9-28
A099 Process Factor
30.0
9-29
A100 Fault Clear
0 = Ready/Idle
9-29
A101 Program Lock
0 = Unlocked
9-29
A102 Testpoint Sel
400
9-29
A103 Comm Data Rate
4 = 19.2 K
9-30
A104 Comm Node Addr
1
9-30
A105 Comm Loss Action
0 = Fault
9-30
A106 Comm Loss Time
5.0 sec
9-31
A107 Comm Format
0 = RTU 8-N-1
9-31
A108 Language
1 = English
9-31
A110 Anlg In 1-10V Lo
0.0%
9-32
A111 Anlg In 0-10V Hi
100.0%
9-32
A112 Anlg In4-20mA Lo
0.0%
9-32
A113 Anlg In4-20mA Hi
100.0%
9-33
A114 Slip Hertz @ FLA
2.0 Hz
9-33
A118 Current Limit 2
Drive Rated
Amps x 1.8
9-33
No.
Parameter Name
Record of User Settings
User Setting
B-3
No.
B-4
Default
Value
Parameter Name
Page
No.
A119 Skip Frequency
0 Hz
9-33
A120 Skip Freq Band
0.0 Hz
9-34
A121 Stall Fault Time
0 = 60 sec
9-34
A122 Analog In Loss
0 = Disabled
9-35
A123 10V Bipolar Enbl
0 = Uni-Polar In
9-35
A124 Var PWM Disable
0 = Enabled
9-36
A125 Torque Perf Mode
1 = Sensrls Vect
9-36
A126 Motor NP FLA
Drive Rated
Amps
9-36
A127 Autotune
0 = Ready/Idle
9-36
A128 IR Voltage Drop
Based on Drive
Rating
9-37
A129 Flux Current Ref
Based on Drive
Rating
9-37
A130 PID Trim Hi
0.0
9-38
A131 PID Trim Lo
0.0
9-38
A132 PID Ref Select
0 = PID Disabled
9-38
A133 PID Feedback Sel
0 = 0-10V Input
9-38
A134 PID Prop Gain
0.00
9-39
A135 PID Integ Time
0.0 sec
9-39
A136 PID Diff Rate
0.0 (1/sec)
9-39
A137 PID Setpoint
0.0%
9-39
A138 PID Deadband
0.0%
9-39
A139 PID Preload
0.0 Hz
9-40
A140 Stp Logic 0
00F1
9-40
A141 Stp Logic 1
00F1
9-40
A142 Stp Logic 2
00F1
9-40
A143 Stp Logic 3
00F1
9-40
A144 Stp Logic 4
00F1
9-40
A145 Stp Logic 5
00F1
9-40
A146 Stp Logic 6
00F1
9-40
A147 Stp Logic 7
00F1
9-40
A150 Stp Logic Time 0
30.0 sec
9-42
A151 Stp Logic Time 1
30.0 sec
9-42
A152 Stp Logic Time 2
30.0 sec
9-42
A153 Stp Logic Time 3
30.0 sec
9-42
A154 Stp Logic Time 4
30.0 sec
9-42
User Setting
MD65 AC Drive User Manual
No.
Parameter Name
Default
Value
Page
No.
A155 Stp Logic Time 5
30.0 sec
9-42
A156 Stp Logic Time 6
30.0 sec
9-42
A157 Stp Logic Time 7
30.0 sec
9-42
Record of User Settings
User Setting
B-5
B-6
MD65 AC Drive User Manual
APPENDIX C
Parameters
Cross-Referenced
by Name
Parameter Name
No.
Parameter
Group
Default
Value
Page
No.
10V Bipolar Enbl
A123 Advanced
0 = Uni-Polar In
9-35
Accel Time 1
P039 Basic
5.0 sec
9-6
Accel Time 2
A067 Advanced
10.0 sec
9-18
Analog In 0-10V
d020 Display
Read Only
9-48
Analog In 4-20mA
d021 Display
Read Only
9-48
Analog In Loss
A122 Advanced
0 = Disabled
9-35
Analog Out High
A066 Advanced
100%
9-17
Analog Out Sel
A065 Advanced
0
9-17
Anlg In 0-10V Hi
A111 Advanced
100.0%
9-32
Anlg In 1-10V Lo
A110 Advanced
0.0%
9-32
Anlg In4-20mA Hi
A113 Advanced
100.0%
9-33
Anlg In4-20mA Lo
A112 Advanced
0.0%
9-32
Auto Rstrt Delay
A093 Advanced
1.0 sec
9-27
Auto Rstrt Tries
A092 Advanced
0
9-26
Autotune
A127 Advanced
0 = Ready/Idle
9-36
Boost Select
A084 Advanced
8 = 5.0, CT
7 = 2.5, CT (for
5.0, 7.5, and
10.0 HP drives
only)
9-23
Break Frequency
A087 Advanced
15.0 Hz
9-25
Break Voltage
A086 Advanced
25.0%
9-24
Comm Data Rate
A103 Advanced
4 = 19.2 K
9-30
Comm Format
A107 Advanced
0 = RTU 8-N-1
9-31
Comm Loss Action
A105 Advanced
0 = Fault
9-30
Comm Loss Time
A106 Advanced
5.0 sec
9-31
Parameters Cross-Referenced by Name
C-1
Parameter Name
C-2
No.
Parameter
Group
Default
Value
Page
No.
Comm Node Addr
A104 Advanced
1
9-30
Comm Status
d015 Display
Read Only
9-47
Commanded Freq
d002 Display
Read Only
9-43
Compensation
A097 Advanced
1 = Electrical
9-28
Contrl In Status
d013 Display
Read Only
9-46
Control Source
d012 Display
Read Only
9-45
Control SW Ver
d016 Display
Read Only
9-47
Counter Status
d025 Display
Read Only
9-49
Current Limit 1
A089 Advanced
Drive Rated
Amps x 1.8
9-25
Current Limit 2
A118 Advanced
Drive Rated
Amps x 1.8
9-33
DB Resistor Sel
A082 Advanced
0 = Disabled
9-22
DC Brake Level
A081 Advanced
Drive Rated
Amps x 0.5
9-21
DC Brake Time
A080 Advanced
0.0 sec
9-21
DC Bus Voltage
d005 Display
Read Only
9-44
Decel Time 1
P040 Basic
5.0 sec
9-6
Decel Time 2
A068 Advanced
10.0 sec
9-18
Dig In Status
d014 Display
Read Only
9-46
Digital In1 Sel
A051 Advanced
4 = Preset Freq
9-8
Digital In2 Sel
A052 Advanced
4 = Preset Freq
9-8
Digital In3 Sel
A053 Advanced
4 = Preset Freq
9-8
Digital in4 Sel
A054 Advanced
5 = Local
9-8
Drive Status
d006 Display
Read Only
9-44
Drive Temp
d024 Display
Read Only
9-49
Drive Type
d017 Display
Read Only
9-47
Elapsed Run Time
d018 Display
Read Only
9-47
Fault 1 Code
d007 Display
Read Only
9-44
Fault 2 Code
d008 Display
Read Only
9-44
Fault 3 Code
d009 Display
Read Only
9-44
Fault Clear
A100 Advanced
0 = Ready/Idle
9-29
Flux Current Ref
A129 Advanced
Based on Drive
Rating
9-37
Flying Start En
A096 Advanced
0 = Disabled
9-28
Internal Freq
A069 Advanced
0.0 Hz
9-19
MD65 AC Drive User Manual
Parameter Name
No.
Parameter
Group
Default
Value
Page
No.
IR Voltage Drop
A128 Advanced
Based on Drive
Rating
9-37
Jog Accel/Decel
A079 Advanced
10.0 sec
9-21
Jog Frequency
A078 Advanced
10.0 Hz
9-20
Language
A108 Advanced
1 = English
9-31
Maximum Freq
P035 Basic
60 Hz
9-2
Maximum Voltage
A088 Advanced
Drive Rated
Volts
9-25
Minimum Freq
P034 Basic
0.0 Hz
9-2
Motor NP FLA
A126 Advanced
Drive Rated
Amps
9-36
Motor NP Hertz
P032 Basic
60 Hz
9-2
Motor NP Volts
P031 Basic
Varies
9-2
Motor OL Current
P033 Basic
Varies
9-2
Motor OL Select
A090 Advanced
0 = No Derate
9-25
Opto Out Logic
A064 Advanced
0
9-16
Opto Out1 Level
A059 Advanced
0.0
9-16
Opto Out1 Sel
A058 Advanced
0 = Ready/Fault
9-14
Opto Out2 Level
A062 Advanced
0.0
9-16
Opto Out2 Sel
A061 Advanced
2 = Motor
Running
9-14
Output Current
d003 Display
Read Only
9-43
Output Freq
d001 Display
Read Only
9-43
Output Power
d022 Display
Read Only
9-48
Output Power Fctr
d023 Display
Read Only
9-48
Output Voltage
d004 Display
Read Only
9-43
PID Deadband
A138 Advanced
0.0%
9-39
PID Diff Rate
A136 Advanced
0.0 (1/sec)
9-39
PID Feedback Sel
A133 Advanced
0 = 1-10V Input
9-38
PID Integ Time
A135 Advanced
0.0 sec
9-39
PID Preload
A139 Advanced
0.0 Hz
9-40
PID Prop Gain
A134 Advanced
0.00
9-39
PID Ref Select
A132 Advanced
0 = PID
Disabled
9-38
PID Setpoint
A137 Advanced
0.0%
9-39
PID Trim Hi
A130 Advanced
0.0
9-38
PID Trim Lo
A131 Advanced
0.0
9-38
Parameters Cross-Referenced by Name
C-3
Parameter Name
C-4
No.
Parameter
Group
Default
Value
Page
No.
Preset Freq 0
A070 Advanced
0.0 Hz
9-20
Preset Freq 1
A071 Advanced
0.0 Hz
9-20
Preset Freq 2
A072 Advanced
0.0 Hz
9-20
Preset Freq 3
A073 Advanced
0.0 Hz
9-20
Preset Freq 4
A074 Advanced
0.0 Hz
9-20
Preset Freq 5
A075 Advanced
0.0 Hz
9-20
Preset Freq 6
A076 Advanced
0.0 Hz
9-20
Preset Freq 7
A077 Advanced
0.0 Hz
9-20
Process Display
d010 Display
Read Only
9-45
Process Factor
A099 Advanced
30.0
9-29
Program Lock
A101 Advanced
0 = Unlocked
9-29
PWM Frequency
A091 Advanced
4.0 kHz
9-26
Relay Out Level
A056 Advanced
0.0
9-13
Relay Out Sel
A055 Advanced
0 = Ready/Fault
9-11
Reset to Defalts
P041 Basic
0 = Ready/Idle
9-7
Reverse Disable
A095 Advanced
0 = Rev
Enabled
9-27
S Curve%
A083 Advanced
0% (Disabled)
9-22
Skip Freq Band
A120 Advanced
0.0 Hz
9-34
Skip Frequency
A119 Advanced
0 Hz
9-33
Slip Hertz @ FLA
A114 Advanced
2.0 Hz
9-33
Speed Reference
P038 Basic
0 = Drive Pot
9-5
Stall Fault Time
A121 Advan ced
0 = 60 sec
9-34
Start At PowerUp
A094 Advanced
0 = Disabled
9-27
Start Boost
A085 Advanced
5.0%
9-24
Start Source
P036 Basic
0 = Keypad
9-3
Stop Mode
P037 Basic
1 = Coast, CF
9-4
Stp Logic 0
A140 Advanced
00F1
9-40
Stp Logic 1
A141 Advanced
00F1
9-40
Stp Logic 2
A142 Advanced
00F1
9-40
Stp Logic 3
A143 Advanced
00F1
9-40
Stp Logic 4
A144 Advanced
00F1
9-40
Stp Logic 5
A145 Advanced
00F1
9-40
Stp Logic 6
A146 Advanced
00F1
9-40
Stp Logic 7
A147 Advanced
00F1
9-40
Stp Logic Status
d028 Display
Read Only
9-49
MD65 AC Drive User Manual
Parameter Name
No.
Parameter
Group
Default
Value
Page
No.
Stp Logic Time 0
A150 Advanced
30.0 sec
9-42
Stp Logic Time 1
A151 Advanced
30.0 sec
9-42
Stp Logic Time 2
A152 Advanced
30.0 sec
9-42
Stp Logic Time 3
A153 Advanced
30.0 sec
9-42
Stp Logic Time 4
A154 Advanced
30.0 sec
9-42
Stp Logic Time 5
A155 Advanced
30.0 sec
9-42
Stp Logic Time 6
A156 Advanced
30.0 sec
9-42
Stp Logic Time 7
A156 Advanced
30.0 sec
9-42
SW Current Trip
A098 Advanced
0.0 (Disabled)
9-28
Testpoint Data
d019 Display
Read Only
9-48
Testpoint Sel
A102 Advanced
400
9-29
Timer Status
d026 Display
Read Only
9-49
Torque Perf Mode
A125 Advanced
1 = Sensrls
Vect
9-36
Var PWM Disable
A124 Advanced
0 = Enabled
9-36
Parameters Cross-Referenced by Name
C-5
C-6
MD65 AC Drive User Manual
APPENDIX D
CE Conformance
Requirements
Conformity with the Low Voltage (LV) Directive and Electromagnetic
Compatibility (EMC) Directive has been demonstrated using
harmonized European Norm (EN) standards published in the
Official Journal of the European Communities. The MD65 AC drive
complies with the EN standards listed below when installed
according to the User Manual.
CE Declarations of Conformity are available online at:
http://www.reliance.com/certification/.
Low Voltage Directive (73/23/EEC)
•
EN50178 Electronic equipment for use in power installations.
EMC Directive (89/336/EEC)
•
EN61800-3 (Second Environment) Adjustable speed electrical
power drive systems Part 3: EMC product standard including
specific test methods.
General Notes
•
If the plastic top panel is removed or the optional conduit box is
not installed, the drive must be installed in an enclosure with side
openings less than 12.5 mm (0.5 in) and top openings less than
1.0 mm (0.04 in) to maintain compliance with the LV Directive.
•
The motor cable should be kept as short as possible in order to
avoid electromagnetic emission as well as capacitive currents.
•
The use of line filters in ungrounded systems is not
recommended.
•
Conformity of the drive with CE EMC requirements does not
guarantee an entire machine installation complies with the CE
EMC requirements. Many factors can influence total
machine/installation compliance.
CE Conformance Requirements
D-1
Essential Requirements for CE Compliance
The following conditions must be satisfied for MD65 drives to meet
the requirements of EN61800-3.
•
Grounding as described in figure D.1. Refer to chapter 4 for
additional grounding recommendations.
•
Output power, control (I/O) and signal wiring must be braided,
shielded cable with a coverage of 75% or better, metal conduit
or equivalent attenuation.
•
Allowable cable length in table D.1 is not exceeded.
Table D.1 – Allowable Cable Length
External - Short1
EN61800-3
First Environment
EN61800-3
First Environment
Restricted Distribution
or Second
Unrestricted
Environment2
Distribution3
10 meters (33 feet)
1 meter (3 feet)
10 meters (33 feet)
1 meter (3 feet)
External - Long1
100 meters (328 feet)
Filter Type
Integral
5 meters (16 feet)
1
Contact Reliance Electric for details on optional external filters.
2
Equivalent to EN55011 Class A.
3
Equivalent to EN55011 Class B.
(1)
Shielded Enclosure
IP 30/NEMA 1/UL Type 1
NEMAKit1/IP30 Kit
Option
(2)
EMI Fittings and Metal Conduit
EMI Filter
L1
L2
L3
L1'
L2'
L3'
R/L1
S/L2
T/L3
Enclosure Ground Connection
U/T1
V/T2
W/T3
Shielded Motor Cable
Building Structure Steel
(1) First Environment Unrestricted Distribution installations require a
shielded enclosure. Keep wire length as short as possible between
the enclosure entry point and the EMI filter.
(2) Integral EMI filters are available on 240 V, 1-phase drives.
Figure D.1 – Connections and Grounding
D-2
MD60 AC Drive User Manual
EN61000-3-2
•
0.75 kW (1 HP) 240 V 1-phase and 3-phase drives and
0.37 kW (0.5 HP) 240 V 1-phase drives are suitable for
installation on a private low-voltage power network.
Installations on a public low-voltage power network may require
additional harmonic mitigation.
•
Other drive ratings meet the current harmonic requirements of
EN61000-3-2 without additional external mitigation.
CE Conformance Requirements
D-3
D-4
MD60 AC Drive User Manual
APPENDIX E
Accessories
E.1 Dynamic Brake Modules
Table E.1 – Dynamic Brake Modules
Input Voltage
120V 50/60 Hz
1-Phase
240V 50/60 Hz
1-Phase
240V 50/60 Hz
3-Phase
480V 50/60 Hz
3-Phase
1
2
Accessories
Drive Ratings
kW
0.4
0.75
1.1
0.4
0.75
1.5
2.2
0.4
0.75
1.5
2.2
3.7
5.5
7.5
0.4
0.75
1.5
2.2
4.0
5.5
7.5
HP
0.5
1.0
1.5
0.5
1.0
2.0
3.0
0.5
1.0
2.0
3.0
5.0
7.5
10.0
0.5
1.0
2.0
3.0
5.0
7.5
10.0
Model Number1
2
AK-R2-091P500
AK-R2-091P500
2
AK-R2-091P500
AK-R2-091P500
AK-R2-047P500
2
AK-R2-091P500
AK-R2-091P500
AK-R2-047P500
AK-R2-047P500
AK-R2-030P1K2
AK-R2-030P1K2
2
AK-R2-360P500
AK-R2-360P500
AK-R2-120P1K2
AK-R2-120P1K2
AK-R2-120P1K2
AK-R2-120P1K2
The resistors listed in this table are rated for 5% duty cycle.
Drive does not support dynamic braking.
E-1
Frame A
Frame B
30.0
(1.18) 60.0
(2.36)
31.0
(1.22)
59.0
(2.32)
C
US
C
US
17.0
(0.67)
61.0
(2.40)
335.0
(13.19)
386.0
(15.20)
405.0
(15.94)
SURFACES MAY BE
ROCKWELL
AUTOMATION
AUTOMATION
ROCKWELL
316.0
(12.44)
13.0
(0.51)
Frame
A
B
Model Number
AK-R2-091P500, AK-R2-047P500, AK-R2-360P500
AK-R2-030P1K2, AK-R2-120P1K2
Figure E.1 – Dynamic Brake Modules: Dimensions
E-2
MD65 AC Drive User Manual
E.2 EMC Line Filters
Table E.2 – EMC Line Filters
Drive Ratings
Input Voltage
kW
120V 50/60 Hz
0.4
1-Phase
0.75
240V 50/60 Hz
1-Phase
240V 50/60 Hz
3-Phase
480V 50/60 Hz
3-Phase
1.1
0.4
0.75
1.5
2.2
0.4
0.75
1.5
2.2
3.7
5.5
7.5
0.4
0.75
1.5
2.2
4.0
5.5
7.5
HP
0.5
1.0
1.5
0.5
1.0
2.0
3.0
0.5
1.0
2.0
3.0
5.0
7.5
10.0
0.5
1.0
2.0
3.0
5.0
7.5
10.0
S Type Filter
Model Number 1
–
–
–
2
2
2
2
6MDF-021B53
6MDF-021B53
6MDF-021B53
6MDF-021B53
6MDF-021B53
6MDF-034CS
6MDF-034CS
6MDF-012BS
6MDF-012BS
6MDF-012BS
6MDF-012BS
6MDF-012BS
6MDF-018CS
6MDF-018CS
L Type Filter
Model Number 4
6MDF-018BL
6MDF-018BL
6MDF-018BL
6MDF-018BL
6MDF-018BL
6MDF-018BL
6MDF-025CL
6MDF-021BL
6MDF-021BL
6MDF-021BL
6MDF-021BL
6MDF-021BL
6MDF-034CL
6MDF-034CL
6MDF-012BL
6MDF-012BL
6MDF-012BL
6MDF-012BL
6MDF-012BL
6MDF-018CL
6MDF-018CL
1
This filter is suitable for use with a cable length of at least 10 meters
(33 feet) for Class A and 1 meter for Class B environments.
2
These ratings can be ordered with internal “S Type” filters.
3
Filter must be Series B or later.
4 This filter is suitable for use with a cable length of at least 100 meters
for Class A and 5 meters for Class B environments.
Accessories
E-3
29.8
(1.17)
50
(1.97)
100
78 (3.94)
(3.07)
217
(8.54)
229
(9.02)
216
(8.50)
17.8
(0.70)
5.5 (0.22)
24.0
(0.94)
Dimensions are in mm and (in).
Model Numbers: 6MDF-012BS, -BL; 6MDF-021BS, -BL;
6MDF-018BS, -BL
Figure E.2 – Frame B EMC Line Filters: Dimensions
E-4
MD65 AC Drive User Manual
32
(1.26)
60
(2.36)
130
90 (5.12)
(3.54)
297
(11.69)
309
(12.17)
297
(11.69)
17
(0.67)
30
(1.18)
5.5 (0.22)
Dimensions are in mm and (in).
Model Numbers: 6MDF-018CS, -CL; 6MDF-034CS, -CL;
6MDF-025CL
Figure E.3 – Frame C EMC Line Filters: Dimensions
Accessories
E-5
E.3 Operator Interface Modules (OIMs)
Table E.3 – Operator Interface Modules/Accessories
Description
Model Number
Remote Panel-Mount OIM (digital speed control,
CopyCat capable, IP66 (NEMA 4x12) indoor use only,
includes 2.9 meter cable)
MD4LCD-PNL
Remote Handheld OIM (digital speed control, full
numeric keypad, CopyCat capable, IP30 (NEMA Type
1); includes 1.0 meter cable; panel-mount with optional
Bezel Kit)
MD1CC
Bezel Kit (panel mount for Remote Handheld OIM)
MDBZL-N1
OIM Cable (1.0 meter OIM-to-RJ45 cable)
MDCBL-CC1
OIM Cable (2.9 meter OIM-to-RJ45 cable)
MDCBL-CC3
E-6
MD65 AC Drive User Manual
17.6
(0.69)
104
(4.09)
220
(8.66)
2.9m
78
(3.07)
66
(2.60)
194
(7.64)
125
(4.92)
60.5
(2.38)
19.1
(0.75)
38
(1.50)
4.8
(0.19)
Dimensions are in mm and (in).
Figure E.4 – Remote OIM (M/N MD4LCD-PNL)
Accessories
E-7
93
(3.66)
25.2
(0.99)
11.1
(0.44)
180
(7.09)
2m
67
(2.64)
60
(2.36)
154
(6.06)
4.8
(0.19)
77
(3.03)
19.1
(0.75)
23.5
(0.93)
Dimensions in mm and (in).
Figure E.5 – NEMA Type 1 Bezel (M/N MDBZL-N1): Dimensions
E-8
MD65 AC Drive User Manual
APPENDIX F
RS485 (MDI)
Protocol
MD65 drives support the RS485 (MDI) protocol to allow efficient
operation with Rockwell Automation peripherals. In addition, some
Modbus functions are supported to allow simple networking. MD65
drives can be multi-dropped on an RS485 network using Modbus
protocol in RTU mode.
Controller
Figure F.1 – Sample Network
For information regarding DeviceNet or other communication
protocols, refer to the appropriate user manual.
Network Wiring
Network wiring consists of a shielded 2-conductor cable that is
daisy-chained from node to node. See figure F.2.
MD65 Drive
Node 1
Master
TxRxD+
4
120 ohm resistor
TxRxD-
5
Shield
MD65 Drive
Node 2
TxRxD+
TxRxDShield
4
5
MD65 Drive
Node "n"
TxRxD+
TxRxD-
4
5
Shield
FRONT
120 ohm resistor
PIN 1
PIN 8
X
X
X
NOTE: The shield is connected at ONLY ONE end of each cable segment.
Figure F.2 – Network Wiring Diagram
Only pins 4 and 5 on the RJ45 plug should be wired. The other pins
on the MD65 RJ45 socket contain power, etc., for other Rockwell
Automation peripheral devices and must not be connected.
RS485 (MDI) Protocol
F-1
Wiring terminations on the master controller will vary depending on
the master controller used and “TxRxD+” and “TxRxD-” are shown
for illustration purposes only. Refer to the master controller’s user
manual for network terminations. Note that there is no standard for
the “+” and “-” wires, and consequently Modbus device
manufacturers interpret them differently. If you have problems with
initially establishing communications, try swapping the two network
wires at the master controller.
Standard RS485 wiring practices apply. Termination resistors need
to be applied at each end of the network cable. RS485 repeaters
may need to be used for long cable runs, or if greater than 32 nodes
are needed on the network.
Control Terminal 16 on the MD65 must also be connected to PE
ground (there are two PE terminals on the drive).
Parameter Configuration
The following MD65 parameters are used to configure the drive to
operate on a network.
Table F.1 – MD65 Network Parameters
Parameter
P036 (Start Source)
P038 (Speed Reference)
A103 (Comm Data Rate)
A104 (Comm Node Addr)
A105 (Comm Loss Action)
A106 (Comm Loss Time)
A107 (Comm Format)
F-2
Details
Set to 5 “RS485 (MDI) Port” if Start is controlled
from the network.
Set to 5 “RS485 (MDI) Port” if the Speed Reference
is controlled from the network.
Sets the data rate for the RS485 (MDI) Port. All
nodes on the network must be set to the same data
rate.
Sets the node address for the drive on the network.
Each device on the network requires a unique node
address.
Selects the drive’s response to communication
problems.
Sets the time that the drive will remain in
communication loss before the drive implements
A105 (Comm Loss Action).
Sets the transmission mode, data bits, parity and
stop bits for the RS485 (MDI) Port. All nodes on the
network must be set to the same setting.
MD65 AC Drive User Manual
Supported Modbus Function Codes
The peripheral interface (MDI) used on MD65 drives supports some
of the Modbus function codes.
Table F.2 – Supported Modbus Function Codes
Modbus Function Code
03
06
Important:
RS485 (MDI) Protocol
Command
Read Holding Registers
Preset (Write) Single Register
Modbus devices can be 0-based (registers are
numbered starting at 0) or 1-based (registers are
numbered starting at 1). Depending on the Modbus
Master used, the register addresses listed on the
following pages may need to be offset by +1. For
example, Logic Command may be register address
8192 for some master devices (e.g., ProSoft 3150MCM SLC Modbus scanner) and 8193 for others
(e.g., PanelViews).
F-3
Writing (06) Logic Command Data
The MD65 drive can be controlled via the network by sending
Function Code 06 writes to register address 8192 (Logic
Command). P036 (Start Source) must be set to 5 “RS485 (MDI)
Port” in order to accept the commands.
Table F.3 – Logic Commands
Logic Command
Address
(Decimal)
Bit(s)
0
1
2
3
5,4
6
7
9,8
8192
11,10
14,13,12
15
F-4
Description
1 = Stop, 0 = Not Stop
1 = Start, 0 = Not Start
1 = Jog, 0 = No Jog
1 = Clear Faults, 0 = Not Clear Faults
00 = No Command
01 = Forward Command
10 = Reverse Command
11 = Change Direction (Toggle)
Not Used
Not Used
00 = No Command
01 = Accel Rate 1 Enable
10 = Accel Rate 2 Enable
11 = Hold Accel Rate Selected
00 = No Command
01 = Decel Rate 1 Enable
10 = Decel Rate 2 Enable
11 = Hold Decel Rate Selected
000 = No Command
001 = Freq. Source = P036 (Start Source)
010 = Freq. Source = A069 (Internal Freq)
011 = Freq. Source = Comms (Addr 8193)
100 = A070 (Preset Freq 0)
101 = A071 (Preset Freq 1)
110 = A072 (Preset Freq 2)
111 = A073 (Preset Freq 3)
Not Used
MD65 AC Drive User Manual
Writing (06) Reference
The Speed Reference to a MD65 drive can be controlled via the
network by sending Function Code 06 writes to register address
8193 (Reference). P038 (Speed Reference) must be set to 5
“RS485 (MDI) Port” in order to accept the Speed Reference.
Table F.4 – Reference
Reference
Address
(Decimal)
8193
Description
A decimal value entered as xxx.x where the decimal point is
fixed. For example, a decimal “100” equals 10.0 Hz and “543”
equals 54.3 Hz.
Reading (03) Logic Status Data
The MD65 Logic Status data can be read via the network by
sending Function Code 03 reads to register address 8448 (Logic
Status).
Table F.5 – Logic Status Data
Logic Status
Address
(Decimal)
8448
RS485 (MDI) Protocol
Bit(s)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
1 = Ready, 0 = Not Ready
1 = Active (Running), 0 = Not Active
1 = Cmd Forward, 0 = Cmd Reverse
1 = Rotating Forward, 0 = Rotating Reverse
1 = Accelerating, 0 = Not Accelerating
1 = Decelerating, 0 = Not Decelerating
1 = Alarm, 0 = No Alarm
1 = Faulted, 0 = Not Faulted
1 = At Reference, 0 = Not At Reference
1 = Reference Controlled by Comm
1 = Operation Cmd Controlled by Comm
1 = Parameters have been locked
Digital Input 1 Status
Digital Input 2 Status
Not Used
Not Used
F-5
Reading (03) Feedback
The Feedback (Output Frequency) from the MD65 drive can be
read via the network by sending Function Code 03 reads to register
address 8451 (Feedback).
Table F.6 – Feedback
Feedback1
Address
(Decimal)
8451
1
F-6
Description
A xxx.x decimal value where the decimal point is fixed. For
example, a decimal “123” equals 12.3 Hz and “300” equals
30.0 Hz.
Returns the same data as Reading (03) Parameter d001 (Output Freq).
MD65 AC Drive User Manual
Reading (03) Drive Error Codes
The MD65 Error Code data can be read via the network by sending
Function Code 03 reads to register address 8449 (Drive Error
Codes).
Table F.7 – Error Codes
Logic Status
Address
(Decimal)
8449
RS485 (MDI) Protocol
Value
(Decimal)
0
2
3
4
5
6
7
8
12
13
29
33
38
39
40
41
42
43
63
64
70
80
81
100
122
Description
No Fault
Auxiliary Input
Power Loss
Undervoltage
Overvoltage
Motor Stalled
Motor Overload
Heatsink Overtemperature
HW Overcurrent (300%)
Ground Fault
Analog Input Loss
Auto Restart Tries
Phase U to Ground Short
Phase V to Ground Short
Phase W to Ground Short
Phase UV Short
Phase UW Short
Phase VW Short
Software Overcurrent
Drive Overload
Power Unit Fail
AutoTune Fail
Communication Loss
Parameter Checksum Error
I/O Board Fail
F-7
Reading (03) and Writing (06) Drive Parameters
To access drive parameters, the Modbus register address equals
the parameter number. For example, a decimal “1” is used to
address parameter d001 (Output Freq) and decimal “39” is used to
address parameter P039 (Accel Time 1).
F-8
MD65 AC Drive User Manual
APPENDIX G
RJ45 Splitter Cable
The MD65 drive provides a RJ45 port to allow the connection of a
single peripheral device. The RJ45 Splitter Cable can be used to
connect a second MDI peripheral device to the drive.
Connectivity Guidelines
ATTENTION: The peripherals may not perform as intended if
these Connectivity Guidelines are not followed. Precautions
should be taken to follow these Connectivity Guidelines.
Failure to observe these precaution may result in damage to,
or destruction of, the equipment.
!
•
Two peripherals maximum can be attached to a drive.
•
If a single peripheral is used, it must be connected to the
Master port (M) on the splitter and configured for “Auto”
(default) or “Master.” Parameter 9 (Device Type) on the OIM
keypads and parameter 1 (Module Cfg) on the Serial Converter
are used to select the type (Auto / Master / Slave).
•
Do not use the RJ45 Splitter Cable with a drive that has an
internal network communication module installed. Since
only one additional peripheral can be added, the second
peripheral can be connected directly to the RJ45 port on the
drive. The internal Comm is always the Master, therefore the
external peripheral must be configured as “Auto” (for temporary
connections) or “Slave” (for permanent connections).
•
If two peripherals will be powered up at the same time, one
must be configured as the “Master” and connected to the
Master port (M) and the other must be connected as the
“Slave” and connected to the Slave port (S).
RJ45 Splitter Cable
G-1
PIN 1
S
Slave Port
M
Cable Accessories
Master Port
PIN 8
Figure G.1 – RJ45 Splitter Cable (M/N AK-U0-RJ45-SCI)
TB2
(PIN 5)
PIN 8
TB1
(PIN 4)
PIN 1
Figure G.2 – RJ45 Two-Position Terminal Block Module
M/N AK-U0-RJ45-TB2P
PIN 8
PIN 1
Figure G.3 – RJ45 Module With Integrated Termination Resistor
(M/N AK-U0-RJ45-TR1)
G-2
MD65 AC Drive User Manual
Connecting One Temporary Peripheral
MD65 Drive
MD65
Handheld OIM
Serial Converter
or
M
S
Parameter 1 (Module Cfg) set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Parameter 9 (Device Type) set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Figure G.4 – Connecting One Temporary Peripheral
Connecting One Temporary Peripheral and
One Permanent Peripheral
NEMA 1 Bezel
with Handheld OIM
NEMA 4
Panel Mount OIM
MD65 Drive
or
M
S
Parameter 1 (Module Cfg)
set to "Auto" (default) or
"Slave" and connected to
Slave port (S) on
RJ45 Splitter Cable
Parameter 9 (Device Type)
set to "Master" and
connected to Master port
(M) on RJ45 Splitter Cable
Serial Converter
Figure G.5 – Connecting One Temporary Peripheral and One Permanent
Peripheral
RJ45 Splitter Cable
G-3
Connecting Two Permanent Peripherals
NEMA 1 Bezel
with Handheld OIM
NEMA 4
Panel Mount OIM
MD65 Drive
or
M
Parameter 9 (Device Type) set to
"Master" and connected to Master
port (M) on RJ45 Splitter Cable
S
Parameter 9 (Device Type)
set to "Slave" and
connected to Slave port (S)
on RJ45 Splitter Cable
or
Figure G.6 – Connecting Two Permanent Peripherals
Connecting an RS485 Network
MD65 Drives
Esc
Sel
AK-U0-RJ45-TB2P
Two-position
Terminal Block
AK-U0-RJ45-TR1
Terminating Resistor
(end of network)
or
or
Customer-supplied RJ45 male-to-RJ45 male
cables with wires connected at pins 4 and 5 only.
Both the Master (M) and Slave (S) ports on the RJ45 Splitter
Cable operate as standard RS-485 ports in this configuration.
Figure G.7 – Connecting an RS485 Network
G-4
MD65 AC Drive User Manual
INDEX
Numerics
10V Bipolar Enbl (A123), 9-35
A
A parameters, 9-8 to 9-33
Accel Time 1 (P039), 9-6
Accel Time 2 (A067), 9-18
accel/decel selection, 6-11
accessories, 2-4, E-1 to E-8
Advanced parameters, 9-8 to 9-33
Analog In 0-10V (d020), 9-48
Analog In Loss (A122), 9-35
Analog Input 4-20mA (d021), 9-48
Analog Input Loss fault, 10-4
Analog Out High (A066), 9-17
Analog Out Sel (A065), 9-17
Anlg In 0-10V Hi (A111), 9-32
Anlg In 0-10V Lo (A110), 9-32
Anlg In4-20mA Hi (A113), 9-33
Anlg In4-20mA Lo (A112), 9-32
Auto Restart feature, 10-2
Auto Restart Tries fault, 10-4
Auto Rstrt Delay (A093), 9-27
Auto Rstrt Tries (A092), 9-26
Autotune (A127), 9-36
Auxiliary Input fault, 10-3
B
Basic parameters, 9-2 to 9-7
Bezel Kit, 2-4, E-6, E-8
Boost Select (A084), 9-23
Break Frequency (A087), 9-25
Break Voltage (A086), 9-24
C
cables, 2-4
catalog number, 2-2
CE conformance requirements, D-1 to
D-3
circuit breakers, 5-6 to 5-7, A-2
Comm Data Rate (A103), 9-30
Index
Comm Format (A107), 9-31
Comm Loss Action (A105), 9-30
Comm Loss fault, 10-5
Comm Loss Time (A106), 9-31
Comm Node Addr (A104), 9-30
Comm Status (d015), 9-47
Commanded Freq (d002), 9-43
Compensation (A097), 9-28
Contrl In Status (d013), 9-46
control and signal wiring
recommendations, 6-3
Control Source (d012), 9-45
Control SW Ver (d016), 9-47
control terminal block
wiring, 6-4
control wiring, installing, 6-1 to 6-11
control, 2- and 3-wire, 6-9
Counter Status (d025), 9-49
cover, opening, 5-1
Current Limit 1 (A089), 9-25
Current Limit 2 (A118), 9-33
D
d parameters, 9-43 to 9-48
DB Resistor Sel (A082), 9-22
DC Brake Level (A081), 9-21
DC Brake Time (A080), 9-21
DC Bus Voltage (d005), 9-44
Decel Time 1 (P040), 9-6
Decel Time 2 (A068), 9-18
DeviceNet Communication Module, 2-4
Digital In1 Sel (A051), 9-8
Digital In2 Sel (A052), 9-8
Digital In3 Sel (A053), 9-8
Digital In4 Sel (A054), 9-8
dimensions, drive, 3-3
display description, 8-2
Display parameters, 9-43 to 9-48
drive
catalog numbers, 2-2
frame size, 2-2
grounding, 4-1 to 4-2
model numbers, 2-2
mounting, 3-1 to 3-6
Index-1
operating conditions, 3-2
powering up after installing, 7-2
ratings, 2-2
storage guidelines, 2-5
troubleshooting, 10-1 to 10-11
Drive Overload fault, 10-5
Drive Status (d006), 9-44
Drive Temp (d024), 9-49
Drive Type (d017), 9-47
Dynamic Brake Modules, E-1
E
Elapsed Run Time (d018), 9-47
EMC Line Filters, E-3
F
fault
buffers, see, Fault n Code
(d007-d009)
clearing automatically, 10-2
clearing manually, 10-2
codes, about, 10-1
descriptions and corrective
actions, 10-3
log, see, Fault n Code (d007-d009)
Fault 1 Code (d007), 9-44
Fault 2 Code (d008), 9-44
Fault 3 Code (d009), 9-44
Fault Clear (A100), 9-29
faults
Analog Input Loss, 10-4
Auto Restart Tries, 10-4
Auxiliary Input, 10-3
Comm Loss, 10-5
Drive Overload, 10-5
Ground Fault, 10-4
Heatsink OverTemp, 10-4
HW OverCurrent, 10-4
I/O Board Fail, 10-6
Motor Overload, 10-3
Motor Stalled, 10-3
OverVoltage, 10-3
Parameter Checksum, 10-6
Params Defaulted, 10-5
Phase Short, 10-5
Phase to Ground Short, 10-4
Phase UW Short, 10-5
Phase V to Gnd, 10-4
Phase VW Short, 10-5
Index-2
Phase W to Gnd, 10-4
Power Loss, 10-3
Power Unit, 10-5
SVC Autotune, 10-5
SW OverCurrent, 10-5
UnderVoltage, 10-3
filter, RFI, 4-2
Flux Current Ref (A129), 9-37
Flying Start En (A096), 9-28
frames and ratings, 2-2
fuses, 5-6 to 5-7, A-2
G
Ground Fault, 10-4
ground fault monitoring, 4-1
grounding the drive, 4-1 to 4-2
H
Heatsink OverTemp fault, 10-4
HW OverCurrent fault, 10-4
I
I/O Board Fail fault, 10-6
I/O wiring, 6-4
I/O wiring examples, 6-6, 6-9
input potentiometer, 6-6
input power conditioning, 5-4
installation, 7-1
Internal Freq (A069), 9-19
IR Voltage Drop (A128), 9-37
J
Jog Accel/Decel (A079), 9-21
Jog Frequency (A078), 9-20
jumper, removing, 5-3
K
key descriptions, 8-3
keypad components, 8-1
kits, 2-4
L
Language (A108), 9-31
LED descriptions, 8-2
MD65 AC Drive User Manual
M
Maximum Freq (P035), 9-2
Maximum Voltage (A088), 9-25
Minimum Freq (P034), 9-2
model numbers, 2-1
motor cable length, 5-10
motor cable types, 200-600 V
installations, 5-8
Motor NP FLA (A126), 9-36
Motor NP Hertz (P032), 9-2
Motor NP Volts (P031), 9-2
Motor OL Current (P033), 9-2
Motor OL Select (A090), 9-25
Motor Overload fault, 10-3
Motor Stalled fault, 10-3
motor start/stop precautions, 6-2
mounting specifications, 3-6
mounting the drive, 3-1 to 3-6
MOVs, 5-3
multiple drive connection examples, 6-9
N
NEMA 1/IP30 Kit,, 2-4
O
OIMs, E-6
operating conditions, 3-2
Operator Interface Modules (OIMs), E-6
Opto Out Logic (A064), 9-16
Opto Out1 Level (A059), 9-16
Opto Out1 Sel (A058), 9-14
Opto Out2 Level (A062), 9-16
Opto Out2 Sel (A061), 9-14
Output Current (d003), 9-43
output disconnect, 5-10
Output Freq (d001), 9-43
Output Power (d022), 9-48
Output Power Fctr (d023), 9-48
Output Voltage (d004), 9-43
OverVoltage fault, 10-3
P
P parameters, 9-2 to 9-7
Parameter Checksum fault, 10-6
Parameter Groups, 8-4
parameters
A, 9-8 to 9-33
about, 8-4
Index
Advanced, 9-8 to 9-33
Basic, 9-2 to 9-7
cross-referenced by name, C-1 to
C-5
d, 9-43 to 9-48
descriptions, 9-1 to 9-48
Display, 9-43 to 9-48
P, 9-2 to 9-7
record of user settings, B-1 to B-5
viewing and adjusting Basic (P) and
Advanced (A), 8-5
viewing Display (d), 8-6
Params Defaulted fault, 10-5
PE ground, 4-2
Phase Short fault, 10-5
Phase to Ground fault, 10-4
Phase UW Short fault, 10-5
Phase V to Gnd fault, 10-4
Phase VW Short fault, 10-5
Phase W to Gnd fault, 10-4
PID Deadband (A138), 9-39
PID Diff Rate (A136), 9-39
PID Feedback Sel (A133), 9-38
PID Integ Time (A135), 9-39
PID Preload (A139), 9-40
PID Prop Gain (A134), 9-39
PID Ref Select (A132), 9-38
PID Setpoint (A137), 9-39
PID Trim Hi (A130), 9-38
PID Trim Lo (A131), 9-38
potentiometer, wiring, 6-6
Power Loss fault, 10-3
power terminal block
connections, 5-5
specifications, 5-5
Power Unit fault, 10-5
power wiring specifications, 5-8
power wiring, installing, 5-1 to 5-10
power-off checks, 7-1
Preset Freq 0 (A070), 9-20
Preset Freq 1 (A071), 9-20
Preset Freq 2 (A072), 9-20
Preset Freq 3 (A073), 9-20
Preset Freq 4 (A074), 9-20
Preset Freq 5 (A075), 9-20
Preset Freq 6 (A076), 9-20
Preset Freq 7 (A077), 9-20
Process Display (d010), 9-45
Process Factor (A099), 9-29
Program Lock (A101), 9-29
protective features, A-3
PWM Frequency (A091), 9-26
Index-3
R
reflected wave protection, 5-10
Relay Out Sel (A055), 9-11
Relay Output Level (A056), 9-13
Reliance Electric, contacting, 1-1
Remote Handheld OIM, 2-4
Remote Panel-Mount OIM, 2-4
Reset to Defalts (P041), 9-7
Reverse Disable (A095), 9-27
RFI filter grounding, 4-2
RJ45 Splitter Cable, G-1 to G-4
RS485 (MDI) protocol, F-1 to F-8
S
S Curve % (A083), 9-22
safety ground, 4-2
Serial Converter Module, 2-4
shield termination, 4-2
shielded motor cable, 5-9
Skip Freq Band (A120), 9-34
Skip Frequency (A119), 9-33
Slip Hertz @ FLA (A114), 9-33
specifications, technical, A-1
Speed Reference (P038), 9-5
speed reference control, 6-10
Stall Fault Time (A121), 9-34
Start At PowerUp (A094), 9-27
Start Boost (A085), 9-24
Start Source (P036), 9-3
starting up the drive, 7-1
stop circuit requirements, 6-1
Stop Mode (P037), 9-4
storage guidelines, 2-5
Stp Logic 0 (A140), 9-40
Stp Logic 1 (A141), 9-40
Stp Logic 2 (A142), 9-40
Stp Logic 3 (A143), 9-40
Stp Logic 4 (A144), 9-40
Stp Logic 5 (A145), 9-40
Stp Logic 6 (A146), 9-40
Index-4
Stp Logic 7 (A147), 9-40
Stp Logic Status (d028), 9-49
SVC Autotune fault, 10-5
SW Current Trip (A098), 9-28
SW OverCurrent fault, 10-5
T
technical assistance, 1-1
terminal block
control, 6-4
power, 5-5
Testpoint Data (d019), 9-48
Testpoint Select (A102), 9-29
three-wire control, 6-9
Timer Status (d026), 9-49
Torque Perf Mode (A125), 9-36
troubleshooting tables, 10-7 to 10-11
troubleshooting the drive, 10-1 to 10-11
two-wire control, 6-9
U
UnderVoltage fault, 10-3
ungrounded distribution systems, 5-2
unshielded power cables, 5-8
V
Var PWM Disable (A124), 9-36
VS Utilities Software, 2-4
W
weight, drive, 3-3
wiring
I/O examples, 6-9
potentiometer, 6-6
wiring specifications
control and signal, 6-3
power, 5-8
MD65 AC Drive User Manual
This document, as well as more information about Reliance Electric products, can be
found at www.reliance.com/drives.
Publication D2-3519-1 May 2003
 2003 Rockwell Automation. All rights reserved. Printed in USA.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement