Viking Professional VESC5304B Installation guide

Viking Professional VESC5304B Installation guide
Viking Installation Guide
®
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20508J EN
Professional & Designer
Freestanding 30” Electric Range
(081610)
Table of Contents
IMPORTANT–Read and Follow!
Warnings & Important Safety Instructions _______________________________________________3
Dimensions _________________________________________________________________________6
Specifications _______________________________________________________________________7
Clearance Dimensions (Proximity to Cabinets) ___________________________________________8
Clearance Dimensions (Wood/Composite Overlay) ______________________________________9
Electrical Requirements _____________________________________________________________10
General Information ________________________________________________________________11
Installation _________________________________________________________________________12
Door Removal ______________________________________________________________12
Leg Installation______________________________________________________________13
Electrical Connection (3-wire) _________________________________________________14
Electrical Connection (4-wire) _________________________________________________16
Leveling/Adjustments/Alignment ______________________________________________18
Anti-tip Device Installation____________________________________________________19
Final Installation _____________________________________________________________20
Door Replacement and Adjustment ___________________________________________21
Final Preparation ___________________________________________________________________22
Performance Checklist ______________________________________________________________22
Service & Registration_______________________________________________________________23
• Before beginning, please read these
instructions completely and carefully.
Your safety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
• Do not remove permanently affixed labels,
warnings, or plates from product. This may
void the warranty.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes or in the absence
of codes, the National Fuel Gas Code
ANSIZ223.1/NFPA-54 –latest edition.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future reference.
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death
In Canada: Installation must be in accordance
with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death
CAUTION
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
2
3
IMPORTANT–Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which
are not installed properly or do not meet the requirements below.
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
If
•
•
•
•
WARNING
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat resistant
adhesive must be used if the product is to
be installed in laminated cabinetry. Check
with your builder or cabinet supplier to
make sure that the materials meet these
requirements.
DANGER
ELECTRICAL SHOCK
HAZARD
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been properly
grounded in accordance with local codes
or in absence of codes, with the National
Electrical Code (NEC). ANSI/NFPA 70latest edition.
WARNING
MOVING HAZARD
To avoid risk of severe
personal injury; this appliance
requires two or more personnel while
handling and moving. Possible use of
appliance moving devices is recommended.
WARNING
TIPPING HAZARD
To reduce the risk of the
appliance tipping, it must be
secured by a properly installed
anti-tip bracket(s). To make sure
the bracket has been installed
properly, look behind the range
with a flashlight to verify proper
installation engaged in the rear
top left corner of the range.
• THIS RANGE CAN TIP.
• INJURIES TO PERSONS CAN RESULT.
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE.
• SEE INSTALLATION INSTRUCTIONS.
4
5
Specifications
Dimensions
VESC/DSCE
Electric 30” Range
29
1”
(2.
5
29-7/8” (75.9 cm)
Overall height
To top of glass frame
35-7/8” (91.1 cm) min.
37” (94.0 cm) max.
Legs adjust 1-1/8” (2.9 cm)
Overall depth from
rear
To
To
To
To
Additions to base
height
To top of island trim—add 1” (2.5 cm)
To top of island trim—add 0” (0.0 cm)
To top of backguard—add 8” (20.3 cm)
To top of backguard—add 6” (15.2 cm)
To top of high-shelf—add 23-1/2” (59.7 cm) To top of high-shelf—add 18-3/16” (46.2 cm)
cm
)
3
(91 5-7
.1 /8”
cm
)
to min
.
(94 37
.0 ”
cm
)m
ax
.
VESC
Electrical
requirements
Surface element rating
Left front
Bridge
Left rear
Right front
Bridge
Right rear
DSCE
1-1/2”
1-5/8”
(4.1 cm)
25” (63.5 cm)
1” (2.5 cm)
end of side panel—24-5/16” (61.8 cm)
front of door—25-3/4” (65.4 cm)
end of landing ledge—28-1/16” (71.3 cm)
end of door handle—28-11/16” (72.9 cm)
(3.8 cm)
6”
(15.2 cm)
240V—59.0 amps
208V—51.3 amps
1,500 watts
NA
2,500 watts/1,000 watts
1,800 watts
800 watts
1,800 watts
1,800 watts
800 watts
1,800 watts
1,500 watts
NA
2,500 watts/1,000 watts
25-5/16” (64.6 cm)
Oven interior height
16-1/2” (41.9 cm)
Oven interior depth
AHAM 16-13/16” (42.7 cm) Overall—19-1/2” (49.5 cm)
8-1/8”
Total oven capacity—4.7 cu. ft.
Measure to AHAM standards 4.1 cu. ft.
Approximate
shipping weight
28-1/4” (71.8 cm)
end of side panel—25” (63.5 cm)
front of door—25-3/4” (65.4 cm)
end of landing ledge—26-1/2” (67.3 cm)
end of door handle—28-1/4” (71.8 cm)
Oven interior width
Oven volume
(20.6 cm)
To
To
To
To
See Electrical Requirements information.
Maximum amp usage
26-1/2” (67.3 cm)
28-1/16” (71.2 cm)
DSCE130-4B
Overall width
*
26-7/16” (67.2 cm)
VESC530-4B
Description
(75-7/8
.9 ”
cm
)
426 lbs. (193.2 kg)
35-7/8”
35-7/8”
25” (63.5 cm)
(91.1 cm) min.
to
37”
(94.0 cm) max.
19-3/8”
(91.1 cm) min.
to
37”
(94 cm) max.
25-3/4” (65.4 cm)
19-1/4”
(49.2 cm)
Minimum clearances from adjacent combustible construction
• Cooking surface and below, i.e., 36” (91.4 cm) and below
o Sides—0”
o Rear—0” with backguard or highshelf; 0” with island trim and noncombustible rear wall; 6” (15.2 cm) with island
trim and combustible rear wall.
• Above cooking surface, i.e. above 36" (91.4 cm)
o Sides—6” (15.2 cm)
o Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface.
o Wall cabinets directly above product must be minimum 36” (91.4 cm) for open top burners above cooking surface.
25-3/4” (65.4 cm)
(48.9 cm)
45” (114.3 cm)
45-1/8” (114.6 cm)
24-5/16” (61.8 cm)
24” (61.0 cm)
*Note: Units shown with standard island trim.
6
7
Clearance Dimensions
• This range may be installed directly
adjacent to existing 36” (91.4 cm) high
base cabinets.
Clearance Dimensions (Wood/Composite Overlay)
(Proximity to Cabinets)
CAUTION
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat and moisture
resistant adhesive must be used if the
product is to be installed in laminated
cabinetry. Check with your builder or
cabinet supplier to make sure that the
materials meet these requirements.
IMPORTANT: The side trim MUST be
3/8” (.95 cm) above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit using the
adjustment spindles on the legs.
• The range CANNOT be installed directly
adjacent to sidewalls, tall cabinets, tall
appliances, or other side vertical surfaces
above 36” (91.4 cm) high. There must be a
minimum of 6” (15.2 cm) side clearance
from the range to such combustible
surfaces above the 36” (91.4 cm) counter
height.
The bottom of a standard hood should be
30” (76.2 cm) min. to 36” (91.4 cm) max.
above the countertop. This would typically
result in the bottom of the hood being
66” (167.6 cm) to 72” (182.9 cm) above the
floor. Refer to the range hood installation
instructions for additional information. These
dimensions provide for safe and efficient
operation of the hood.
Wo
od
/Co
Ov mpo
erl sit
ay e
”
24 cm)
.0
(61 or
66
(16 ”mi
7.6 n.
c
to m)
”
27 cm)
.6
(38
72
(18 ”ma
2.9 x.
cm
)
• Within the 6” (15.2 cm) side clearance to
combustible vertical surfaces above 36”
(91.4 cm), the maximum wall cabinet
depth must be 13” (33.0 cm) and wall
cabinets within this 6” (15.2 cm) side
clearance must be 18” (45.7 cm) above the
36” (91.4 cm) high countertop.
0” )
m
c
(0
30
(76”min
.2 .
cm
36 to )
”
m
(91 a
.4 x.
cm
)
29
(75-7/8
.9 ”
cm
)
x.
a
m
)
” m
133.0 c
(3
6”
(15 min
.2 .
cm
)
• Wall cabinets above the range must be a
minimum of 42” (106.7 cm) above the
range cooking surface for the full width of
the range. This minimum height
requirement does not apply if a range
hood is installed over the cooking surface.
Wo
od
/Co
Ov mpo
erl sit
ay e
in.
” mcm)
2
4 .7
6
(10
in.
”m )
18 .7 cm
(45
”
36 m)
c
.4
(91
”
3/8 m)
c
95
(0.
CAUTION
”
30 cm)
66
.2
(76
72
6” m)
.2 c
5
(1
(16 ”mi
7.6 n.
c
to m)
(18 ”ma
2.9 x.
cm
)
Wall Installation
30
(76”min
.2 .
cm
3 6 to )
”
(91 ma
.4 x.
cm
)
Note: Minimum clearance for back wall
is 0” with backguard or high-shelf.
Burn hazard.
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns. If a cabinet
storage is to be provided the risk can be
reduced by installing a rangehood that
projects horizontally a minimum 5” (12.7 cm)
beyond the bottom of cabinets.
(op
en A
ing
wi d
th)
Range
Width
30”
“A”
Dimension
30” (76.2 cm)
Note: Minimum clearance for back wall is 0” with backguard
or high-shelf.
Note: 6” (15.2 cm) min. with island trim and
combustible rear wall. 0” with island trim
and non-combustible rear wall.
Island Installation
Note: If a range hood is installed, wall cabinets above the
range have a different minimum clearance height.
8
9
Electrical Requirements
Electrical Requirements
• Viking Range Corporation will NOT
warranty any problems resulting from GFI
outlets which are not installed properly or
do not meet the requirements below.
This product is manufactured with the
neutral terminal connected to the cabinet.
Use a 3-wire, agency approved, power
supply kit with closed loop terminals rated
per the National Electrical Code, ANSI/NFPA
70-latest edition (See Rating chart below). If
local codes prohibit grounding through the
neutral, use a 4-wire, agency approved,
power supply kit with closed loop terminals
rated per the National Electrical Code,
ANSI/NFPA 70-latest edition (See Rating
chart below).
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or
portable type NOT recommended)
• Used with permanent wiring only
(temporary or portable wiring NOT
recommended)
• On a dedicated circuit (no other
receptacles, switches or loads in the
circuit)
• Connected to a standard breaker of
appropriate size (GFI breaker of the same
size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip
current) as per UL 943 standard
• In good condition and free from any
loose-fitting gaskets (if applicable in
outdoor situations)
• Protected from moisture (water, steam,
high humidity) as much as reasonably
possible
RATING*
Specified Rating of Power
Supply Cord Kit and Circuit Protection
120/240 Volts
12.5 - 16.5 KW
16.5 - 17.5 KW
120/208 Volts
9.2 - 12.5 KW
12.5 - 13.5 KW
General Information
Amps
40 or 50
50
*The National Electric Code calculation for
Electrical Load is less than the Total
Connected Electrical Load listed on the
model/serial rating plate.
A GFI shall be used if required by NFPA70 (National Electric Code),
federal/state/local laws, or local
ordinances.
• The required use of a GFI is normally
related to the location of a receptacle with
respect to any significant sources of water
or moisture.
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned
off at the breaker box until the range is
installed and ready to operate, installation
by an authorized installer only.
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
Range – Do not discard the anti-tip
metal bracket supplied with the
range. This is the anti-tip device and
must be installed with the unit. Refer
to “Anti-tip Device Installation”
section.
• DO NOT obstruct the flow of combustion
and ventilation air.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
Electric 30”
Range
Electrical
connection
in this area
6”
6”
(15.2 cm)
(15.2 cm)
4-3/8”
(11.1 cm)
10
11
DANGER
Leg Installation
Installation
2
1
CAUTION
To avoid risk of personal injury or product
damages, DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. DO NOT lift or carry
the door by the handle.
1
1
3
Removing the door must be done by your
dealer, or a qualified licensed plumber.
2
2
Legs are packed in styrofoam top pack.
Note: Legs should be installed near to where
appliance is to be used, as they are
not secure for long transit.
Door Removal
1FOR YOUR SAFETY
2
Open door completely. Place pins,
supplied with unit, in pin hole. For personal safety,
ONLY use pins supplied with the unit.
4
3
Remove hinge trim screws. Take off hinge trim. Identify
right and left hinge for future re-installation.
3
Note: It is strongly recommended
that a pallet or lift jack be used rather than tilting.
Raise unit about a foot. Unscrew temporary legs from
couplings.
Lower range gently to keep any undue strain from
legs and internal mounting hardware.
Screw legs into couplings on all
four corners.
4
Close until pins stop door.
Lift door up and out.
12
13
Electrical Connection (3-wire)
Note: If you have a 4-wire connection, see following section for
4-wire connection instructions.
WARNING
5
4
WARNING
Electrical shock hazard.
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
1
2
3
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
Attach line #1 (black) and line #2 (red)
leads to outside terminal. Attach neutral wire (white)
to center terminal on the terminal block.
See Electrical Requirements information.
6
1
1
Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.
2
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
1
2
Remove access door.
Reattach access door.
3
2
3
1
1
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on terminal block.
Feed supply cord up through hole in bottom
of range back.
14
15
Electrical Connection (4-wire)
5
4
WARNING
WARNING
Electrical shock hazard.
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
See Electrical Requirements information.
2
Feed supply cord up through hole in bottom
of range back.
Attach ground wire (green)
with ground screw that was removed.
6
1
7
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
1
2
1
Remove access door.
3
2
3
Attach line #1 (black) and line #2 (red)
leads to outside terminal. Attach neutral wire (white)
to center terminal on terminal block.
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
8
1
3
1
1
2
Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.
1
2
1
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on the terminal block.
2
Remove grounding screw. Cut-off
and discard ground strap.
16
Reattach access door.
17
Leveling/Adjustments/Alignment
2
1
Measure the four corners in cutout area to
verify if flooring is level.
7
For uneven or sloped floors, level unit with
metal shims only, as the adjustment required may
exceed the thread available in the leg.
Set the high corner of range so that the top of side trim is
3/8” (0.95 cm) above countertop. Level range to high corner.
Anti-tip Device Installation
4
3
Tipping hazard.
”
3/8cm)
95
(0.
Check that unit is level side to
side and front to back. Side trim of the high corner
must be 3/8” (0.95 cm) above countertop.
Move unit into opening.
6
5
1
WARNING
•
•
•
•
To reduce the risk of the appliance
tipping, it must be secured by a
properly installed anti-tip bracket(s).
To make sure the bracket has been
installed properly, look behind the
range with a flashlight to verify
proper installation engaged in the
rear top left corner of the range.
THIS RANGE CAN TIP.
INJURIES TO PERSONS CAN RESULT.
INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE.
SEE INSTALLATION INSTRUCTIONS.
2
(A
)
Measure from floor to bottom
of the anit-tip opening located on the back of range.
This will be measurement (A).
3
3-5
(9. /8”
2
cm
)
1
1
+1
)
)
(A .3 cm
1
(
/2”
2
If leveling is required, move unit out of opening.
Lift unit and prop on wood blocks.
18
Locate anti-tip bracket on rear wall with the top left corner at
measurement (A) plus 1/2” (1.3 cm) from the floor and 3-5/8” (9.2 cm)
from where the right side of range (facing range) is to be located.
19
Mark and drill holes where bracket
will be located.
Door Replacement and Adjustment
Anti-tip Device Installation (cont.)
4
2
1
1
2
1
2
2
3
Reattach door to range.
Attach bracket with
mounting hardware provided.
Open door completely. Reattach hinge trim.
Final Installation
3
1
4
Note: Refer to range electrical
requirements section for proper
installation information.
Remove pins from hole in hinges.
Connect electrical in shaded area. See the “Electrical
Requirements” section for more information.
3
2
Close door.
5
”
3/8cm)
95
(0.
Check that unit is level side to side
and front to back. The side trim must be 3/8” (0.95 cm)
above countertop. If unit is not level repeat steps 5-7
of “Leveling/Adjustments/Alignment” section.
Slide range into place. Be sure anti-tip
bracket slides into the anit-tip opening.
20
If the door needs to be adjusted, loosen hinge trim screws (see step 2).
Adjust the screws located between the door and kickplate using a 5/32”
hex head allen wrench. After adjustment, tighten hinge trim screws.
21
Service & Registration
Final Preparation
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleansers, or powders!
If it is necessary to scrape stainless steel
to remove encrusted materials, soak with
hot, wet cloths to loosen the material, then
use a wool or nylon scraper. DO NOT use
a metal knife, spatula, or any other
material tool to scrape stainless steel!
Scratches are almost impossible to
remove.
Performance Checklist
A qualified installer should carry out the
following checks:
h Check self-clean function—door will lock
in approximately 30 seconds, the center
and outside broil elements will turn on and
the bake element will turn on at partial
power. Check broil elements through
window to make sure they are on, then
abort self-clean cycle to unlock door.
h Check top surface elements—glow red
when turned on.
h Check hot surface indicator lights—glow
red when corresponding element is on.
NOTICE
h Check oven bake function—bake element
on full power, center and outside broil
elements at partial power.
When conducting performance test,
DO NOT run self-clean cycle for more
than 10 minutes with oven racks inside
oven. This could cause them to discolor
due to the high temperature required
for self-cleaning.
h Convection bake function—bake and broil
elements the same with the convection fan
on.
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Range – The serial number and model number for your appliance can be
found by opening the door and looking under the control panel.
Record the following information indicated below. You will need it if
service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
h Check TruConvec™ function—TruConvec
element (behind convection fan cover) on
and convection fan on.
Dealer's name _____________________________________________________________________________________
h Check HI broil function–both broil
elements at full power.
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit for future reference.
h Check LOW broil function—inner broil
element only.
h Check convection broil function—both
broil elements at full power with convection
fan on.
22
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement