Black & Decker CD701 Instruction manual

Black & Decker CD701 Instruction manual
CD701
1
Copyright Black & Decker
2
2
3
1
4
A
B
3
1
C
D
4
E
4
ENGLISH
HEATGUN CD701
CONGRATULATIONS!
You have chosen a Black & Decker tool. Our aim is
to provide quality tools at an affordable price.
We hope that you will enjoy using this tool for
many years.
EC DECLARATION OF CONFORMITY
CD701
Black & Decker declares that these
products conform to: 98/37/EC,
89/336/EEC, 73/23/EEC, EN 55014,
EN 60335, EN 61000
LpA
(sound pressure)
dB(A)
68
LWA (acoustic power)
dB(A)
81
Always wear ear protection if the sound
pressure exceeds 85 dB(A).
INTENDED USE
Your Black & Decker heatgun CD701 has been
designed for the following applications:
- Removing paint and lacquer
- Removing stickers
- Waxing and dewaxing of skis
- Drying wood
- Drying paint and lacquer
- Thawing frozen pipes
This tool is intended for consumer use only.
SAFETY INSTRUCTIONS
Warning symbols
The following symbols are used in this manual:
Denotes risk of personal injury, loss of life
or damage to the tool in case of nonobservance of the instructions in this
manual.
Hand/arm weighted vibration value:
Denotes risk of electric shock.
< 2.5 m/s2
Read the manual prior to operation.
Know your tool
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
◆
◆
◆
◆
Warning! When using mains-powered
tools, basic safety precautions,
including the following, should always
be followed to reduce the risk of fire,
electric shock, personal injury and
material damage.
Read all of this manual carefully before
operating the tool.
Before operating the tool, make sure
that you know how to switch the tool off
in an emergency.
Retain this manual for future reference.
5
ENGLISH
General
1. Keep work area clean
Cluttered areas and benches can cause
accidents.
2. Consider work area environment
Do not expose the tool to rain. Do not use the
tool in damp or wet conditions. Keep the work
area well lit. Do not use the tool where there is
a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3. Keep children away
Do not allow children, visitors or animals to
come near the work area or to touch the tool
or mains cable.
4. Dress properly
Do not wear loose clothing or jewellery, as
these can be caught in moving parts. Preferably
wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair
covering to keep long hair out of the way.
5. Personal protection
Always use safety glasses. Use a face or dust
mask whenever the operations may produce
dust or flying particles. Wear ear protection
whenever the sound level seems
uncomfortable.
6. Guard against electric shock
Prevent body contact with earthed or
grounded surfaces (e.g. pipes, radiators,
cookers and refrigerators). Electric safety can
be further improved by using a high-sensitivity
(30 mA/30 mS) residual current device (RCD).
7. Do not overreach
Keep proper footing and balance at all times.
8. Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
9. Secure workpiece
Use clamps or a vice to hold the workpiece. It is
safer and it frees both hands to operate the tool.
10. Connect dust extraction equipment
If devices are provided for the connection of
dust extraction and collection facilities, ensure
that these are connected and properly used.
11. Remove keys and adjusting wrenches
Always check that keys and adjusting wrenches
are removed from the tool before operating
the tool.
6
12. Extension cables
Before use, inspect the extension cable and
replace if damaged. When using the tool
outdoors, only use extension cables intended
for outdoor use.
13. Use appropriate tool
The intended use is described in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which
it was intended. Do not force the tool.
Warning! The use of any accessory or attachment
or performance of any operation with this tool
other than those recommended in this instruction
manual may present a risk of personal injury.
14. Check for damaged parts
Before use, carefully check the tool and mains
cable for damage. Check for misalignment and
seizure of moving parts, breakage of parts,
damage to guards and switches and any other
conditions that may affect its operation. Ensure
that the tool will operate properly and perform
its intended function. Do not use the tool if any
part is damaged or defective. Do not use the
tool if the switch does not turn it on and off.
Have any damaged or defective parts repaired
or replaced by an authorised repair agent.
Never attempt any repairs yourself.
15. Unplug the tool
Unplug the tool when it is not in use, before
changing any parts of the tool, accessories or
attachments and before servicing.
16. Avoid unintentional starting
Do not carry the tool with a finger on the on/
off switch. Be sure that the tool is switched off
when plugging in.
17. Do not abuse cord
Never carry the tool by its cord or pull it to
disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
18. Store idle tools
When not in use, tools should be stored in a
dry, locked up or high place, out of reach of
children.
19. Maintain tools with care
Keep cutting tools sharp and clean for better
and safer performance. Follow the instructions
for maintenance and changing accessories.
ENGLISH
Keep handles and switches dry, clean and free
from oil and grease.
20. Repairs
This tool complies with relevant safety
requirements. Repairs should only be carried
out by qualified persons using original spare
parts; otherwise this may result in considerable
danger to the user.
Additional safety instructions for heatguns
General
◆ Do not place your hand over the air vents or
block the vents in any way.
◆ The nozzle of this tool becomes extremely hot
during use. Let it cool down before touching.
◆ Always switch the tool off and allow it to cool
before putting it down.
◆ Do not leave the tool unattended while it is
switched on.
◆ A fire may arise if the appliance is not used
with care.
◆ Be careful when using the tool in places where
there are combustible materials. Do not apply
to the same place for a long time. Heat may be
conducted to combustible materials which are
out of sight.
◆ Do not use the tool in an explosive atmosphere.
◆ Place the tool on its stand after use and allow it
to cool before storage.
◆ Do not leave the tool unattended when in use.
◆ Ensure adequate ventilation as toxic fumes
may be produced.
◆ Do not use as a hairdryer.
◆ Do not obstruct either the air intake or nozzle
outlet, as this may cause excessive heat build
up resulting in damage to the tool.
◆ Do not direct the hot air blast at other people.
◆ Do not touch the metal nozzle as it becomes
very hot during use and remains hot for up to
30 minutes after use.
◆ Do not place the nozzle against anything while
using or immediately after use.
◆ Do not poke anything down the nozzle as it could
give you an electric shock. Do not look down the
nozzle while the unit is working because of the
high temperatures being produced.
◆
Do not allow paint to adhere to the nozzle or
scraper as it could ignite after some time.
Removing paint
◆ Do not use this tool to remove paint
containing lead. The peelings, residue and
vapours of paint may contain lead, which is
poisonous. Any pre-1960 building may have
been painted in the past with paint containing
lead and covered with additional layers of
paint. Once deposited on surfaces, hand to
mouth contact can result in the ingestion of
lead. Exposure even to low levels of lead can
cause irreversible damage to the brain and
nervous system. Young and unborn children
are particularly vulnerable.
◆ When removing paint, ensure that the work
area is enclosed. Preferably wear a dust mask.
◆ Do not burn the paint. Use the scraper
provided and keep the nozzle at least 25 mm
away from the painted surface. When working
in a vertical direction, work downwards to
prevent paint from falling into the tool and
burning.
◆ Dispose of all paint debris safely and ensure
that the work area is thoroughly cleaned after
completing the work.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by
young or infirm persons without supervision.
Children must be supervised to ensure they do
not play with the appliance.
◆ If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
ELECTRICAL SAFETY
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
This product must be earthed.
7
ENGLISH
Mains plug replacement
(U.K. & Ireland only)
Using an extension cable
Always use an approved 3-core extension cable
suitable for the power input of this tool (see
technical data). When using a cable reel, always
unwind the cable completely.
PACKAGE CONTENTS
The package contains:
1 Heatgun
1 Instruction manual
◆
◆
◆
◆
◆
◆
◆
◆
Should your mains plug need replacing and
you are competent to do this, proceed as
instructed below. If you are in doubt, contact
an authorised repair agent or a qualified
electrician.
Disconnect the plug from the supply and
remove the fuse from the plug.
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1).
The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective
points in the plug (see above). Brown is for
Live (L) (2), blue is for Neutral (N) (4) and
green/yellow is for Earth (E).
The earth wire should be of a length to ensure
that in the event of the cable being pulled
from the plug, the earth wire is the last to
break contact.
Before replacing the top cover of the mains
plug ensure that the cable restraint (3)
is holding the outer sheath of the cable firmly
and that the leads are correctly fixed at the
terminal screws.
If the plug has a fuse cover, make sure that the
fuse cover is fitted. Do not use the plug if the
fuse cover is missing or damaged.
Never use a light socket.
8
◆
1.
2.
3.
4.
Carefully unpack all parts.
OVERVIEW (fig. A)
On/off switch
Nozzle
Ventilation slots
Hanging hook
USE
Use only one hand to hold the tool.
Do not place your other hand over the
ventilation slots (fig. B).
Switching on and off (fig. C)
◆ To switch the tool on at the low temperature
setting, set the on/off switch (1) to position I.
◆ To switch the tool on at the high temperature
setting, set the on/off switch (1) to position II.
◆ To switch the tool off, set the on/off switch to
position 0.
The nozzle will remain hot for some time
after switching off. After switching off,
suspend the tool on the hanging hook as
shown in fig. E or place it on a table as
shown in fig. D.
Stripping paint
◆ Switch the tool on at the high temperature
setting.
◆ Direct the hot air onto the paint to be
removed.
◆ When the paint softens, scrape the paint away
using a hand scraper.
ENGLISH
Do not direct the heat to points near glass
as the heat could crack the glass.
Stationary use (fig. D)
This tool can also be used in stationary mode.
◆ Place the tool onto a firm and stable surface as
shown.
◆ Make sure that the nozzle points away from you.
◆ Secure the cable to prevent pulling the tool off
the working surface.
Be careful not to drop anything into the
nozzle. Do not touch the nozzle.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
Before performing any maintenance,
switch off and unplug the tool.
◆
◆
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the housing using a damp
cloth. Do not use any abrasive or solventbased cleaner.
PROTECTING THE ENVIRONMENT
Black & Decker provides a facility for
recycling Black & Decker products once
they have reached the end of their
working life. This service is provided free
of charge. To take advantage of this
service please return your product to any
authorised repair agent who will collect
them on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
Black & Decker office at the address indicated in
this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on
the Internet at: www.2helpU.com
Technical data
Voltage
Power input
Air temperature settings (at nozzle)
Weight
VAC
W
°C
kg
CD701
230
1,800
300/500
0.65
GUARANTEE
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee.
This guarantee statement is in addition to and in
no way prejudices your statutory rights.
The guarantee is valid within the territories of the
Member States of the European Union and the
European Free Trade Area.
If a Black & Decker product becomes defective
due to faulty materials, workmanship or lack of
conformity, within 24 months from the date of
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
◆ The product has been used for trade,
professional or hire purposes;
◆ The product has been subjected to misuse or
neglect;
◆ The product has sustained damage through
foreign objects, substances or accidents;
◆ Repairs have been attempted by persons other
than authorised repair agents or Black & Decker
service staff.
To claim on the guarantee, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting your
local Black & Decker office at the address
indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full
details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com
9
ENGLISH
OTHER DIY TOOLS
Black & Decker has a full range of tools that make
DIY jobs easy. If you would like further information
on the following products, please contact our
Service and Information Centre (see the address
page towards the end of this manual) or your local
Black & Decker retailer.
Drills
Cordless screwdrivers
Cordless drills/screwdrivers
Sanders
Jigsaws
Circular saws
Mitre saws
Angle grinders
Planers
Routers
Corded and cordless multi-purpose tools
Paint strippers
Workbenches
We also have a wide range of accessories for the
above tools.
Not all products are available in all countries.
10
ENGLISH
11
ENGLISH
12
13
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Box Hill, Victoria 3128
Tel. 03 9895 9200
Fax 03 9899 7465
New Zealand
Black & Decker
81 Hugo Johnson Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
South Africa
Black & Decker South Africa (Pty) Ltd
Physical address:
39 Commerce Crescent
Eastgate, ext. 12, Sandton, Kramerville 2148
Postal address:
Postnet Suite 107, Private Bag X65
Halfway House 1685
Tel. (011) 653-1400
Fax (011) 653-1499
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
14
580570-00
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Yes
No
Was this tool your first purchase?
Yes
No
Was this tool a gift?
Postal code: .............................................................................................
Town: .......................................................................................................
Address: ...................................................................................................
Name: ......................................................................................................
○
Dealer address
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Data protection act:
Tick the box if you prefer not to receive further information.
Dealer address: ........................................................................................
.................................................................................................................
.................................................................................................................
Yes
No
Was this tool bought as a replacement?
○
Date of purchase
○
✁
15
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
GUARANTEE CARD
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
✁
Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your
country. If you live in Australia or New Zealand, please register by using the alternative guarantee card
supplied.
16
580570-00
○
○
○
○
○
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement