User manual - TEP Ex d.o.o.

User manual - TEP Ex d.o.o.
d.o.o.
10090 Zagreb, Medarska 69
tel. +38549222900
fax +38549426450
e-mail: [email protected]
USER MANUAL FOR EXPLOSION PROTECTED GROUNDING
AND GROUNDING CONTROL DEVICE type GGCD-01/..
No: TEPEx.RS.040
Rev : 2
Date: 25.01.2011.
1. MANUFACTURER
TEP Ex d.o.o. , Medarska 69, HR-10090 Zagreb
tel. +38549/222-900, fax +38549/426-450, e-mail: tepextepex.hr, www.tepex.hr
2. PURPOSE
GGCD 01 device (Grounding and grounding control device) along with the grounding clamps makes the active
system for static grounding and grounding control and it is used in areas that may be endangered by explosive
mixtures of gas and vapoures of flammable liquid with air, in danger zones 1 i 2 according to the HRN EN
60079-10-1:2009 (EN 60079-10-1:2009).
Device ensures that objects like tanks are electrostatic grounded correctly during the loading and unloading of
flammable liquids. The device provides a conductive connection to the ground and monitors in parallel the
quality of the connection. The electrostatic level of the tank is kept ona a safe level. An occasional discharge in
conjunction with sparks is prevented and therefore the explosion protection ensured.
3. DEGREE OF PROTECTION
Explosion protection is in accordance with the "general requirements" in the types of protection "flameproof
enclosure", “ increased safety”, "intrinsic safety" and "encapsulation" in accordance with standards: HRN EN
60079-0:2009, HRN EN 60079-1:2008, HRN EN 60079-7:2007, HRN EN 60079-11:2007 HRN EN 6007918:2010 (EN 60079-0:2009, EN 60079-1:2007, EN 60079-7:2007, EN 60079-11:2007, EN 60079-18:2009).
Apparatus category: II 2G
Explosion protection marking: Ex d e [ib] mb IIC T5 Gb
Ambient temperature: -20°C > Tamb > +50°C
Mechanical protection: IP 66 category 1, according to the EN 60529:1991/A1:2000
Degree of protection: I (protective grounding), according to the EN 61140:2002/A1:2006
Certificate: Ex-Agency [E-1/08] - HREx T 10.024
The device complies with standards:
- CENELEC CLC/TR 50404 (Electrostatics-Code of practice for the avoidance of hazards due to static
electricity),
CEN 1755 +A1 (Safety of industrial trucks-Operation in potentially explosive atmospheres-Use in
flammable gas, vapour, mist and dust),
BGR 132 – BG Rules for avoiding ignition hazards as a result of electromagnetic charges
The product complies with the LV Directive 2006/95/EC, EMC Directive 2004/108/EC and RoHS Directive
2002/95/EC.
1/7
4. MODEL CODE
GGCD 01 / . .
basic device marking
- K1 - type with one clamp K1, with 10m cable,
- K2 - type with two clamps K1, with 2 x 10m cable.
Each version of GGCD device has two operating modes (which can be selected with control switch):
MODE 1 – Device doesn't recognize if object is grounded in any other way in the moment of connecting
grounding clamps. It is used when the object because of itself construction can't be isolated from ground (rail
cars, tank containers). Pushbutton START has no function in this mode.
MODE 2 – Device inside control time (cca 10s) recognize if object is already grounded in some other way with
RZ UK < 7 kΩ, and if clamps are connected correctly to grounded object. Mode is started pushing to START
pushbutton. It can be used when grounded object is isolated from ground (tank trucks, etc...).
Control switch can be locked with padlock in any of operating modes.
5. OPERATING PRINCIPLE
Reaction of the
ground monitoring device
State of grounding process
Clamp is not connected,
grounding equipment not in use
Clamp is directly grounded, e.g. via the
loading platform
Grounding incorrect
• Red indicating lamp ON
• Green indicating lamp OFF
• Contact OPEN
Grounding incorrect (only MOD 2)
• Red indicating lamp ON
• Green indicating lamp OFF
• Contacts OPEN
Clamp connected to
tank vehicle.
Grounding OK
• Red indicating lamp OFF
• Green indicating lamp ON
• Contacts CLOSED
Clamp connected to
tank vehicle, but cable to the grounding is
disconnected.
Grounding incorrect
• Red indicating lamp ON
• Green indicating lamp OFF
• Contacts OPEN
Clamp connected to tank vehicle.
Tank vehicle is grounded subsequently
(e.g. via the loading arm).
Grounding OK
• Red indicating lamp OFF
• Green indicating lamp ON
• Contacts CLOSED
2/7
6. BLOCK DIAGRAM
START
CONECTION TO NETWORK SUPLAY
CONTACTS CONNECTED
PAL1, PAL2 CONNECTED
CLAMPS CONNECTED
TURN ON
MOD2
RED INDICATING LAMP ON
CONTACTS
NO - CLOSED, NC - OPEN
MOD1
RED INDICATING LAMP ON
CONTACTS
NO - CLOSED, NC - OPEN
START
RED INDICATING
BLINKING
t = 10s
NO
YES
RZ> ...
RČ1<...
RČ2<...
CONTINUING LOOP CONTROL
NO
YES
NO
RPAL1<...
RPAL2<...
YES
GREEN INDICATING LAMP ON
CONTACTS
NO - CLOSED,NC - OPEN
NO
POWER SUPLAY
YES
END
7. TECHNICAL DATA
Nominal voltage Un:
Nominal current In:
Nominal power P0 :
Output circuit:
Indicating lamps:
Max. r.m.s. voltage Um:
Max. open circuit voltage U0:
Max. current I0:
Max. power P0:
Max. external inductance L0:
Max. external capacity C0:
230 V ± 10 10%, 50 Hz
50 mA
10 W
2 switch over contacts
Un=250 V AC, In=8 A / 230 V, 4 A at cos φ = 0,4
Red:
- blinking inside control time (10 sec - MOD2),
contacts NO are open, contacts NC are closed,
- continuous operation (MOD1 and MOD 2), contacts NO are
open, contacts NC are closed
Green:
- continuous operation (MOD1 and MOD 2), contacts NO are
closed, contacts NC are open
253 V
15 V
1,60 mA
6,0 mW - linear characteristics
50 mH
45 nF
3/7
Maximum length of the clamp cable:
Connecting terminals:
Stripping length:
Tightening torque of terminal
screws:
Cable ferrules:
Cover screws:
Tightening torque for cover screw:
Cable glands and plugs:
Tightening torque for cable glands:
Tightening torque for plugs:
Clamp cable:
Dimension (LxWxH):
Dimension of clamps holder(L x W x H):
Mounting enclosure onto surface:
Mounting clamps holder onto surface:
Weight (without clamps):
Weight of clamps with 10 m cable:
100 m
- network suplay terminal, output contacts: 1,5-4 mm2 stranded,
flexible
- Cable to the grounding point or busbar for equipotential
bonding: 25 mm2 max. stranded, flexible
4 mm2 - 10 mm, 25 mm2 - 14 mm
terminal 4 mm2 - 0,6 Nm, terminal 25 mm2 - 3,0 Nm
Stranded and flexible cables are installed with cable ferrules
according to DIN 46228 T1
M6x30 (Z4) - 4,8 A2
1,5 Nm
- GGCD 01/K1: 3xM25 Exi cable glands and 2xM25 Exe cable
glands for cable Øv= 9-15 mm, 1 x M25 Exi plug, 1 x M25 Exe
plug
- GGCD 01/K2 - 4xM25 Exi cable glands, 2xM25 Exe cable
glands for cable 15 > Øv > 9 mm, 1 x M25 Exe plug
- cable gland body 3,5 Nm,
- cable gland nut 2,5 Nm
3,5 Nm
3 or 2x1,5 mm2
- cable capacity (wire-wire) 135 nF/km
- wire inductance 0,65 mH/km
- wire resistance 12,0 Ω/km
255 x 250 x 160 mm without clamps
300 x 300 x 195 mm without clamps
With screw kit M6 through the holes in the enclosure Ø7/Ø12 mm
at the top of the rectangle 235 x 200 mm
With screw kit M8 at the top of the rectangle 225 x 260 mm
ca. 6,0 kg
ca. 2,5 kg
8. BLOCK DIAGRAM OF DEVICE AND OPERATING INSTRUCTIONS
It is generally considered that object is satisfactorily electrostatic grounded if resistance to earth is not higher
than 106 Ω.
4/7
Open – closed threshold of output relay depends of clamps resistance RČ=RČ1+RČ2, loop resistance PAL of
conduit RPAL and possible resistance object of grounding of outside grounding RZ (just in MOD 2 operation
inside control time). That given substitute resistance from Z1 to equipotential bonding determines open –
closed threshold RUK ON.
In ideal case when RZ=∞ and RPAL=0 in MOD 2 outside control time and in MOD 1 operation:
- RČ1 + RČ2 < 1,7 kΩ object is electrostatic grounded, green signal light is on, output NO contact is
closed, and NC is open,
- increasing RČ1 + RČ2 > 2,3 kΩ is considering that object is not satisfactorily electrostatic grounded, red
signal light is turning on, output NO contact is opening and NC is closing.
In second case when RZ=0 and RPAL=0 in MOD 2 outside control time and in MOD 1 operation:
- RČ1 < 5,0 kΩ object is electrostatic grounded, green signal light is on, output NO contact is closed and
NC is open,
- increasing RČ1 > 5,6 kΩ s considering that object is not satisfactorily electrostatic grounded, red signal
light is turning on, output NO contact is opening and NC is closing.
Inside control time in MOD 2 operation in boundary case when are RČ1=0 and RČ2=0 in order to electrostatic
grounding is satisfactorily, i.e. that output NO contact is closed, it must be RZ > 7,0 kΩ.
9. INSTALLING, CONTROL, MAINTENANCE AND REPAIR
It is necessary to read this manual before installing and usage and if it is needed to request extra informations from
manufacturer. Installing and usage of device is allowed only to qualified and authorized persons. Installing of device
have to be done in non-voltage state. PAL (equipotential bonding connection) terminals inside device are connected to
PA (equipotential bonding connection) busbar or grounding point with two single wire cables. It that case control loop
is achieved and permanent monitoring of galvanic continuity connection PAL (equipotential bonding connection)
terminal with PA (equipotential bonding connection) busbar or grounding point. Connection is made with conductor
with cross-section 6-25 mm2.
Electric connection, and cables for output connections inside enclosure must be conducted separately from intrinsic
safety conduits. It is not allowed to connect output connectors into other intrinsic safety circuits. Along whole area of
grounding equipotential bonding (PA) must be done. At enclosure closing, cover screws, cable glands and plugs must
be tightened with torque specified in this manual.
Every afterwards enclosure opening is allowed only when supply is switched off.
Before connecting clamps for grounding on the object of grounding, object itself must be electrostaticaly discharged
which must be secured in appropriate way.
5/7
Electric connection scheme of cables and conductors:
6/7
10. SPARE PARTS AND ACCESSORIES
Spare parts
o Control module GGCD 01,
o Connecting cabel 0,5 m with coupler GGCD 01/K1,
o Connecting cable 0,5 m with coupler GGCD 01/K2,
o Clamp K1 with 10 m cable with plug,
o Clamp K2 with 10 m cable with plug,
o Pushbutton PBT 02,
o Signal lamp SLP,
o Switch SMS 03/GGCD,
o Pushbutton actuator SPO 01/7,
o Front element of signal lamp SPO 02/1,
o Front element of signal lamp SPO 02/2,
o Switch actuator SMO 17/GGCD
o Terminal EURO 4/35
o Terminal EURO 4/35 BL
o Terminal EURO E4/35
o Terminal EURO E16-25/35
o Cable gland SPU 25 black,
o Cable gland SPU 25 blue,
o Plug SPC 25 black,
o Plug SPC 25 blue,
o Enclosure gasket SKX 16,
o Enclosure screws SKX 16, M6x30 (Z4) - 4,8 A2
Accessories
o Cable real with 20 m cable, with connector for control modul and clamps, type GGCD 01/KO 20,
o Cable gland for armoured cable type Ex e II, type SIB-DEF 4F, 9 < Øv < 27,5 mm,
6 < Øu< 19,5 mm, f = 1,25 - 16 mm, LCIE 05 ATEX 6146 X
o Telemetry system for remote monitoring of up to 27 devices, type GGCD 01/PC CONTROL. The
system consists of:
 The auxiliary module GGCD 01/M1 located in the unit enclosure,
 Peripheral central unit located outside of the hazardous area - the connection to devices and
to PC computer with RS 232 interface
 Software aplication compatible with Windows operating system
11. MARKING
Explosion protected grounding and grounding control device type GGCD 01/K1, K2 are labeled with internal
and external labels:
HR - 10090 Zagreb
GGCD 01/K1
HR - 10090 Zagreb
0722
230V 50Hz 50mA
II 2G Ex d e [ib] mb IIC T5
Gb
IP66
CESI 11 ATEX ...
MA .......
DATE ......
GGCD 01/K1
0722
230V 50Hz 50mA
II 2G Ex d e [ib] mb IIC T5
Gb
IP66
CESI 11 ATEX ...
MA .......
DATE ......
WARNING - DO NOT OPEN WHEN ENERGIZED
Cable with connector for GGCD 01/K1, GGCD 01/K2 is labeled:
7/7
30.81.01.00C
30.81.01.00D
Clamps K1, K2 for GGCD 01/K1, GGCD 01/K2 are labeled:
Module GGCD 01 is labeled:
TEPEx GGCD 01
30.81.01.00A
12. STORAGE AND TRANSPORT
Transport and storage is only allowed in the original packaging, on the way pointed out on the carton
box.
All rights reserved.
8/7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement