INSTRUCTION MANUAL

DNR Super

High Resolution

Day & Night

Color Camera

1/3” INTERLINE TRANSFER CCD

HIGH RESOLUTION

Please read this manual thoroughly before use and keep it handy for future reference.

WARNINGS AND CAUTIONS

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT

THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ''dangerous voltage'' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

PRECAUTIONS

Safety

Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

Unplug the unit from the wall outlet if it is not going to be used for several days or more.

To disconnect the cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on soft surfaces (rugs, carpets, sofas, etc.) or near materials (curtains, draperies) that may block the ventilation holes.

Height and vertical linearity controls located on the rear panel are for special adjustments by qualified personnel only. ii

Installation

Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration.

The unit is not designed to be waterproof.

Exposure to rain or water may damage the unit.

Cleaning

Clean the unit with a slightly damp soft cloth.

Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER:

THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,

PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED

TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL

INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL

ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN

ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL

INTERFERENCE TO RADIO COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO

CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE

REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION:

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED

BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S

AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME

NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. iii

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been moisture, does not operate normally, or has been dropped.

15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER

THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS

UNLESS YOU QRE QUALIFIED TO DO SO.

16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed

Class 2 power source only.

iv

CONTENTS OF PACKAGE

Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes.

Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment.

The contents of the package includes:

1. Color CCD camera

2. Mini-DIN connector (for video-or dc-type auto-iris lens)

3. CS adapter ring for C mounting “C” lenses

4. This manual

TABLE CONTENTS

INTRODUCTION-------------------------------------------------------------------------------1

COMERA OVERVIEW------------------------------------------------------------------------2

OSD MENU STRUCTURE-------------------------------------------------------------------3

DC IRIS LENS----------------------------------------------------------------------------------10

SPECIFICATIONS-----------------------------------------------------------------------------11 v

INTRODUCTION

The camera provides high-quality images using SONY 1/3” CCD and digital

Signal process LSIs.

Features:

● 1/3" EXview HAD CCD Ⅱ for an image of high sensitivity

● Digital Wide Dynamic Range (Xtended Dynamic Range)

● Excellent picture quality

● 700 lines of resolution

● 0.15Lux(Color), 0.01Lux(B/W) @ F1.2 Sensitivity

● Auto electronic shutter [1/60(1/50) ~ 1/10,000] and manual electronic shutter modes

● OSD (On Screen Display)

● Auto and manual white balance modes

● Auto BLC and HLC

Day & Night (Auto/Manual)

● Privacy Zone 4 point, Motion Detection 4 Point

● MIRROR, SHARPNESS, HUE, CONTRAST, GAIN

● AGC (Auto Gain Control)

● VIDEO OUT(BNC)

● Internal

● Quick connect for DC lens with 4-pin connector

● Operates in 12VDC or 24VAC

● Operates in 100-240VAC

● Use Certified / Listed Class 2 power source only.

● If using DC 12V power adaptor, Please use a power supply capable of supplying over 5.5 Watts.

● Auto White Defect

IMPORTANT :

The user of this camera is responsible for checking and complying with local, state, and federal laws and statutes concerning the recording and monitoring of audio signals.

1

CAMERA OVERVIEW

n

Left Button o Up Button p Enter Button q Right Button r Down Button s Power Indicator t Video Output Connector (BNC) u AC/DC Compatible Input Terminal v AC Power Cord

2

OSD MENU STRUCTURE

SETUP MENU (page 1)

LENS

SHUTTER/AGC

WHITE BAL

BACKLIGHT

PICT ADJUST

ATR

MOTION DET

NEXT (page2)

EXIT SAVE ALL

LENS

AUTO ↵

MANUAL

WHITE BALANCE

ATW ↵

PUSH

USER 1↵

USER 2↵

ANTI CR

MANUAL↵

PUSH LOCK

PICTURE ADJUST↵

MIRROR

BRIGHTNESS

CONTRAST

SHARPNESS

HUE

GAIN

RETURN

ATR

OFF

ON↵

3

SHUTTER/AGC

AUTO↵

MANUAL↵

BACKLIGHT

OFF

BLC

HLC

MOTION DET

OFF

ON↵

SETUP MENU (page 2)

PRIVACY

DAY/NIGHT

NR

CAMERA ID

LANGUAGE

CAMERA RESET

BACK (page 1)

EXIT SAVE ALL

NR↵

NR MODE

Y LEVEL

C LEVEL

RETURN

LANGUAGE

ENGLISH

日本語

DEUTSCH

FRANCAIS

PYCCKNN

PORTUGUES

ESPANOL

PRIVACY

OFF

ON↵

CAMERA ID

OFF

ON↵

4

DAY/NIGHT

AUTO

COLOR

B/W↵

CAMERA RESET

(return the camera to factory defaults)

LENS

AUTO

TYPE

(DC / VIDEO)

Sets the type of mechanical iris

(Video lens is not supported)

MODE

(AUTO / OPEN / CLOSE )

Sets the type of control to be applied over the mechanical iris.

SPEED

(0 – 255)

Sets the convergence speed of the mechanical iris.

MANUAL

Manual lens only

. (Note Since Manual mode AUTO mode is changed SHUTTER/AGC to

SHUT+AUTO IRIS when MANUAL is changed to AUTO, AUTO MODE should be changed to AUTO IRIS in SHUTTER/AGC)

SHUTTER/AGC

AUTO

HIGH LUMINANCE

MODE (SHUT+AUTO IRIS / AUTO IRIS)

(Note: only SHUT can be selected if LENS is in MANUAL mode

SHUT+AUTO IRIS is AE(

Auto Exposure

) for SHUTTER is 1/500(1/480) and

MIRIS)

BRIGHTNESS

(0 ~ 255)

Adjusts the brightness

LOW LUMINANCE

MODE

(AGC / OFF)

Auto Gain Control on or off

BRIGHTNESS

(x0.25 / x0.50 / x0.75/ x1.00)

Amount of AGC applied in low lighting conditions

MANUAL

MODE

(SHUT+ AGC)

Auto gain control

SHUTTER

Select the shutter speed (1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,

1/10000)

AGC

Sets the AGC gain applied [dB] for ME (manual exposure)

(6, 12, 18, 24, 30, 36, 42, 44.8dB)

5

WHITE BAL

ATW

(Auto Trace White balance)

SPEED

(0~255)

Adjusts the pull-in speed of ATW.

DELAY CNT

(0~255)

Sets the time-based hysteresis of ATW.

ATW FRAME

(x0.5 / x1 / x1.5 / x2)

Sets the pull-in frame magnification.

ENVIROMENT

(INDOOR / OUTDOOR)

Preset for either indoor or outdoor applications of the ATW

PUSH

Wide range Auto White Balance mode (AWB)

USER1 & 2

Both USER 1 & 2 can be individually set up for specific applications. The gain values for the outdoor fixed mode are used as the adjustment items of USER1 on the internal OSD menu.

B-GAIN

(0~255)

R-GAIN (0~255)

ANTI CR

Color rolling suppression

MANUAL

The B and R gain values for manual WB are set on this screen.

LEVEL

(NTSC : 13 ~ 56) , (PAL : 16 ~ 78)

PUSH LOCK

PUSHLOCK is selected and the Enter input is active

BACKLIGHT

Sharpens subjects with backlight (OFF / BLC / HLC)

PICT ADJUST

MIRROR

(OFF / ON) Horizontally inverts image.

BRIGHTNESS

(0~255) Sets the screen brightness.

CONTRAST

(0~255) Sets the screen contrast.

SHARPNESS

(0~255) Sets the screen sharpness.

HUE

(0~255) Adjusts the hue.

GAIN

(0~255) Adjusts the gain.

6

ATR

ATR (Adaptive Tone Reproduction) allows adjustment of the image to assist

with widely contrasting scenes of view.

LUMINANCE

(LOW / MID / HIGH)

Sets the extent of the luminance compression

CONTRAST

(LOW / MIDLOW / MID / MIDHIGH / HIGH)

Sets the extent of the contrast enhancement

MOTION DET

DETECT SENSE

(0~127)

Sets the motion detection sensitivity (0=low sensitivity, 127=high sensitivity)

BLOCK DISP

(OFF / ON / ENABLE)

Applies a Motion block trace in the selected area. To define the area, select

Enable and push centrally on the joystick. Use the Joystick to navigate to the blocks you want to Disable and not include in motion trace. To return to the menu, push and hold central joystick for 2secs and release.

MOTION AREA

(ON / OFF)

Enables/disables the motion detection

AREA SEL

(1~4)

Selects the motion detection area

(Note: Set the area sel it would be better

to move firstly BOTTOM and RIGHT)

TOP

(NTSC:0~244 , PAL:0~288)

0 = top

BOTTOM

(NTSC:0~244 , PAL:0~288)

244(288) = bottom

LEFT

(NTSC:0~474 , PAL:0~468)

0 = left

RIGHT

(NTSC:0~474 , PAL:0~468)

474(468) = right

MOTION DET

DETECT SENSE IIIIIIIIIII 111

BLOCK DISP OFF

MONITOR AREA ON

AREA SEL 1/4

TOP IIIIIIIII 000

BOTTOM IIIIIIIII 076

LEFT IIIIIIIII 000

RIGHT IIIIIIIII 183

RETURN

PRIVACY

AREA SEL

(1~4)

Selects the motion detection area

(Note: Set the area sel it would be better

to move firstly BOTTOM and RIGHT)

TOP

(NTSC:0~244 , PAL:0~288)

0 = top

BOTTOM

(NTSC:0~244 , PAL:0~288)

244(288) = bottom

PRIVACY

AREA SEL

AREA SEL 1/4

TOP IIIIIIIIII000

BOTTOM IIIIIIIIII077

LEFT IIIIIIIIII000

RIGHT IIIIIIIIII187

COLOR 1

TRANSP 1.00

MOSAIC OFF

RETURN

7

LEFT

(NTSC:0~474 , PAL:0~468)

0 = left

RIGHT

(NTSC:0~474 , PAL:0~468)

474(468) = right

COLOR

(1~8)

Sets the colors of the privacy zones.

TRANSP

(0.00 / 0.50 / 0.75 / 1.00)

Sets the transparency of the privacy zone area if color is selected.

MOSAIC

(OFF / ON)

Sets the mosaic function as the privacy to ON or OFF.

(Note: when ON, transparency needs to be set at 0.00 and privacy zones

can only be 1 color OR mosaic and not mixed)

DAY / NIGHT

COLOR

(color only operation)

B/W

(monochrome only operation)

BURST

(OFF / ON)

Allows the color burst signal in monochrome to be removed if required.

IR OPTIMIZER

(OFF / ON)

Smart IR mode OFF or ON

MODE

(ONLY IR OPTIMIZER ON, AUTO / CENTER)

Auto : Histogram integration mode

Center : Center priority mode

LEVEL

(ONLY IR OPTIMIZER ON, 0~31)

NR (2D-DNR)

This is used to remove noise from the image in low light conditions when

AGC is applied.

NR MODE (OFF, Y, C, Y/C)

Sets the 2D NR filter mode.

Y LEVEL

(0-15)

Sets the Y filter (Luminance) strength.

C LEVEL

(0-15)

Sets the C filter (Chrominance) strength.

8

CAMERA ID

Sets the camera ID to ON or OFF. A title of 52 characters per line can be

applied.

Use the joystick to navigate the cursor. Pushing centrally on the joystick will allow selection of that character.

The arrows at the bottom allow you to move the cursor without changing the character.

CLR

Inserts a space

POS

Allows you adjust the location of the camera ID title display. (if you move too much right side or down, it might lose ID on the screen)

LANGUAGE

LANGUAGE

select between:

English, Japanese, German, French, Russian, Portuguese & Spanish.

CAMERA RESET

CAMERA RESET

- Returns the camera to the factory default settings.

SAVE ALL

SAVE ALL

- Saves all the changes made in the menu.

EXIT

EXIT

– Exits the menu and does not save changes made.

9

AUTO WHITE DEFECT

Push the left button for 5 seconds and enter Auto white defect menu.

Cover the lens and Enter for starting.

If white defects are over 65pcs, the camera is faulty and auto defect is useless.

Over 70'C Auto white defect can't be activated.

10

DC IRIS LENS

The lens is not supplied with this camera. Purchase a lens suitable for your requirements. These cameras accept both C-and CS-mount type lens.

<Notes >

● For using main functions it is recommended to use Auto Iris Lens with DC type.

● If the lens is marked with fingerprints other marks, the image quality might be poor.

● It is recommended to use a high quality lens to improve the image quality under low illumination.

<INSTALLING AUTO IRIS LENS>

1. Remove the cover from the iris lens plug supplied, and solder the lens cable to the plug as shown below. type:

Pin 1 --- Red (Power source)

Pin 2 --- N.C

Pin 3 --- White (Video signal)

Pin 4 --- Black (GND) type:

Pin 1 --- Damping-

Pin 2 --- Damping+

Pin 3 --- Drive+

Pin 4 --- Drive-

Pin 3

Pin 1

Rib

Connector

Cover

Automatic

Iris Lens

Pin 4

Heat

Shrinkable

Tubes

Pin 2

Iris Control

Cable

Connector

2. Remove the protective cap, and attach the lens to the camera by turning clockwise.

11

SPECIFICATIONS

Power

Power source

DC 12V

/

AC 24V±10%

Power consumption

Image sensor

Total pixels

Effective pixels

Scanning system

3.5 Watts (300mA) 4.0 Watts(60mA)

1/3″ SONY EXview HAD CCD II

1020(H) x 508(V) 1020(H) x 596(V)

976(H)x494(V) 976(H)x582(V)

2:1 Interlace

Scanning frequency

15.734KHz(H)

x 59.94Hz(V)

15.625KHz(H) x 50Hz(V)

Sync. system

Electronic Shutter

1/60 ~ 1/10,000 sec

Internal

1/50 ~ 1/10,000 sec

Resolution 700TVL

Min. illumination

Video output

0.15lux

1.0Vp-p (75 ohm, composite)

S/N ratio

Camera Control

More then 50dB (AGC OFF)

Internal OSD Key

F

U

N

C

T

ATR (Adaptive Tone

Reproduction)

Backlight

Day & Night

MD (Motion Detection)

PM (Privacy Masking)

WB (White Balance)

AGC (Auto Gain Control)

Exposure

Brightness

Contrast

LUMINANCE(L/M/H), CONTRAST(L/LM/M/MH/H)

OFF / BLC / HLC

Color / BW / Auto

"On (4 areas) / Off Adjustable Size & Sensitivity"

0 ~ 4 zone

ATW/ PUSH/ USER1/ USER2/ ANYICR/ MANUAL/ PUSH LOCK

On / Off

Auto Iris / Auto Iris + Electronic Shutter

I

O

N

Sharpness

HUE

Gain

NR(Noise Reduction)

0 ~ 255 steps

0 ~ 255 steps

0 ~ 255 steps

0 ~ 255 steps

0 ~ 255 steps

OFF / Y / C / Y, C

Mirror ON/OFF

Power input 2-pin terminal block Power Cord

Video output

Auto iris output

Lens Mount

Operating temperature

Operating humidity

External dimension

BNC connector

4-Pin Mini Din jack (standard connection)

C/CS Mount (Selected through back focus)

-10ºC ~ +50 ºC

0~96% (non-condensing)

88(W) x 275(H) x 88(D)mm

12

PRINTED IN KOREA

DNR Super High Resolution

Day & Night Color Camera

2

50303278B