ZKTeco L4000 fingerprint lock User manual
Below you will find brief information for fingerprint lock L4000. The fingerprint lock L4000 offers a secure way to control access to your doors. These fingerprint locks are equipped with a fingerprint sensor, a password input, and an optional RF card reader to provide a variety of ways for you to unlock your door. You can set different user privileges for administrators and ordinary users.
Advertisement
Advertisement
Fingerprint Lock User Manual
Version: 1.0.1
Date: May 2010
About This Manual
This manual introduces the fingerprint lock interface and menu operations. For the fingerprint lock installation, see the animated installation instructions.
Our products are subject to update from time to time, so our company will neither make a commitment to guarantee the consistency between the actual products and this document, nor assume any responsibility for any dispute arising out of the discrepancy between the actual technical parameters and this manual. This document is subject to change without prior notice.
Table of Contents
1.1 Introduction to Fingerprint Lock Functions ...................................... 1
1.2 List of Installation Accessories......................................................... 2
1.3 Installation Requirements ................................................................ 4
1.4 Front and Rear Views ...................................................................... 7
2. Enrollment and Verification ................................................................. 13
2.1 Enroll an Administrator ................................................................. 13
2.1.1 Enroll a Fingerprint ................................................................ 14
2.1.2 Enroll a Password ................................................................... 15
2.1.3 Enroll an RF ID Card.............................................................. 16
2.2 Enroll an Ordinary User................................................................. 18
2.3 Backup Enrollment........................................................................ 20
2.4 Set User Verification and NO Status............................................... 21
2.5 FP Card Management * ................................................................. 22
2.5.1 Create a PIN Card................................................................... 23
2.5.2 Enroll an FP Card ................................................................... 25
2.5.3 Create an FP Card................................................................... 27
2.5.4 Purge an FP Card.................................................................... 28
2.6 Delete User Data ........................................................................... 29
3. Lock Function Information and Settings............................................... 32
3.1 Operation Settings ......................................................................... 32
I
3.2 Language Settings ......................................................................... 34
3.3 FP Card Password.......................................................................... 35
3.4 Advanced Settings ......................................................................... 35
3.5 Browse System Information........................................................... 36
3.6 Browse Logs ................................................................................. 37
3.7 USB Pen Drive Management ......................................................... 38
4. Conventions on Other Functions.......................................................... 41
4.1 Routine Operation Indications........................................................ 41
4.2 Administrator Loss Prevention ....................................................... 41
4.3 Battery Low Voltage Protection ..................................................... 41
4.4 Automatic Program Exit and System Poweroff.............................. 42
4.5 External Power Use Description..................................................... 42
4.6 Unlock With an Emergency Mechanical Key ................................. 43
Technical Specifications...................................................................... 45
II
Fingerprint Lock User Manual V1.0.1
1 Instruction for Use
Functions marked with “★” in this manual are only supported by a specific product or a tailormade product and will be described below.
1.1 Introduction to Fingerprint Lock Functions
1. By leveraging the perfect combination of biometrics and cryptography, our fingerprint locks ensure double security through the fingerprint + password unlocking feature.
2. The stateoftheart Organic LED (OLED) display affords crisp bright readouts and makes our fingerprint locks intuitive and easy to use. You can simply use our fingerprint locks with ease after following the operation instructions for once.
3. Support setting of classified privileges for super administrators, administrators and ordinary users.
4. Support deletion of all or the specified registration data.
5. Support firmware upgrade and uploading/downloading of user information and locking records through a USB pen drive.
6. Support offline view of locking records.
7. Support accurate display of time and date with annual deviation less than two minutes.
8. Support a temporary connection with backup batteries.
9. You can set the fingerprint locks to be in the Normally Open (NO) state in special cases.
10. Support display of the battery charge level and generation of lowpressure alarms.
1
Fingerprint Lock User Manual V1.0.1
11. Feature an electric clutch handle design which helps effectively prevent the fingerprint lock failure caused by damage to the internal structure as a result of the forced destruction of the handle.
1.2 List of Installation Accessories
2
Fingerprint Lock User Manual V1.0.1
SN Name
List of Installation Accessories
Quantity Unit Remarks
01 Front panel assembly 1 Set
02 Lock cylinder 1 Set
03 Square shaft of handle 2
04 Lock body 1
05 Battery cover 1
PCS
Set
PCS
06 Batteries 4 PCS
Four pieces of alkaline AA batteries
07 Rear panel assembly 1 Set
08 Screw 6 PCS
Reserve two screws and select proper screw size based on the door thickness
09 Rear holddown plate 1 PCS
10 Waterproof washer 2 PCS
Including the one on the front panel assembly
11 Wood grain screws
12
Screw to secure the cylinder
13 Strike plate
14 Box keep
15 Key
16 Backup battery
5
1
17 Management card
18 Installation disk
19 Hole drilling template 1
1
1
1
2
2
PCS
PCS
Set
PCS
PCS
PCS 9V
PCS Optional
PCS
PCS
3
Fingerprint Lock User Manual V1.0.1
1.3 Installation Requirements
Precautions:
1. The fingerprint lock is applicable to doors of 35–50 mm in thickness. Be sure to list your special requirements or remarks for fingerprint locks to be installed on doors in excess of 50 mm in thickness before placing an order.
2. The gap between the lock body and the box keep cannot exceed 4 mm; otherwise, you need to adopt a liner plate to ensure the gap between them is not more than 4 mm, as shown in the following figure:
≦4mm
3. Please make sure of the door opening directions and lock body. Assume you are standing outside and facing a door and then there are four door opening directions: Left inward, left outward, right inward and right outward. Left inward/outward means the door swings inward/outward with hinges on the left; right inward/outward means the door swings inward/outward with hinges on the right, as shown in the following figure:
4
Fingerprint Lock User Manual V1.0.1
4. Ensure the central point of the handle is about 1m above the floor.
5. Ensure the marker dot of clutch is right above the clutch.
5
Fingerprint Lock User Manual V1.0.1
Marker dot is right above the clutch
6. Please follow the animated instructions to install fingerprint locks.
Recommended Tools
You may need the following tools while following the instructions to install fingerprint locks: l A ruler. l A marker pen. l A drilling tool. l A cross screwdriver.
6
Fingerprint Lock User Manual V1.0.1
1.4 Front and Rear Views
Front view
7
Rear view
Fingerprint Lock User Manual V1.0.1
Battery cover
Band switch
Battery
USB interface
Handle
ESC key:
á key:
Press this key to exit current operation and press and hold this key to power off the fingerprint lock. ESC key doubles as the number key “1”.
This key is used to manually increase (when held, this key will rapidly increase display values) the setup value or navigate among menu options. á key doubles as the number key “2”.
8
Fingerprint Lock User Manual V1.0.1
â key:
Start key:
Band switch:
This key is used to manually decrease (when held, this key will rapidly decrease display values) the setup value or navigate among menu options. â key doubles as the number key “3”.
This key can be used to start the fingerprint lock; press and hold this key for three seconds on the initial interface to open the menu options; this key also doubles as the confirmation (<OK>) key.
If you cannot access the menu options due to the loss of administrators for some reason, proceed as follows: Press and hold the Menu key for three seconds to display the administrator verification, and then turn the Band switch at the back of the lock to the left or right to open up the menu as a super administrator.
Status indicator: You can awake the fingerprint lock in dormant state by pressing the Start key. The green LED indicator blinks when the fingerprint lock operates properly and the red LED indicator is on for three seconds if an error occurs. The green LED indicator is on for three seconds when an operation succeeds.
OLED display: The blackandwhite OLED display features white graphics or text against a black background.
Fingerprint sensor: You can only collect or match fingerprints by pressing your finger(s) at the fingerprint sensor when the light in the fingerprint sensor window goes on; otherwise nothing happens when you press your finger(s) at the fingerprint sensor.
9
Fingerprint Lock User Manual V1.0.1
@
Note: When you cannot power off the fingerprint lock due to the exception of program, press and hold the ESC key to power off and then restart the fingerprint lock. It is not recommended to power off the fingerprint lock by pressing and holding the ESC key when the fingerprint lock operates normally.
Emergency interfaces
Keyhole: You can use a mechanical key for emergency door opening.
Temporary external power interface: You can adopt an external backup battery to open the lock in the event of unlocking failure due to insufficient power supply of the fingerprint lock.
USB interface
The USB interface is used for firmware upgrade and uploading/downloading of user information and locking records through a USB pen drive.
1.5 Precautions
1. We strongly recommend you to enroll at least one administrator after installing the fingerprint lock. You must at least enroll one administrator before enrolling ordinary users.
2. Do not remove batteries when matching, enrolling or deleting fingerprints because the sudden powerdown may result in data loss of fingerprint locks.
Prior to removing batteries, make sure the fingerprint lock is not in working state.
3. It is recommended to replace the fingerprint lock batteries at least once every six months to avoid damaging the circuit due to the battery leakage. Do not use batteries with poor quality.
10
Fingerprint Lock User Manual V1.0.1
4. When installing a fingerprint lock, connect the plug to the socket properly.
Improper connection may lead to fingerprint lock failure.
1.6 User Privileges
The user privileges are classified into three types: Super administrators, administrators and ordinary users.
Super administrators: refer to users who have access to all system functions and modify all system settings.
Administrators: refer to users who have access to all operations except performing advanced settings and enrolling super administrators.
Ordinary users: refer to all users other than the super administrators and administrators. Ordinary users only have access to the fingerprint matching and unlocking functions.
1.7 Set Time
You need to set the correct date and time on first use of a fingerprint lock in the following steps:
1) Power on the fingerprint lock by pressing the
20091124
FP LOCK
Start key to open up the initial interface, as shown in the figure on the left.
Note: The “ ” icon on the initial interface is the battery icon indicating how much charge remains.
On the top right corner of the initial interface, the display alternates between date and time every 5 seconds.
11
Fingerprint Lock User Manual V1.0.1
Menu ↓
User Manage
►Options
PenDrive Mng
2) Press and hold the Menu key for three seconds to access the menu interface. Press ▼ to select
“Options” and press OK to display the setting interface.
Options
Set Opt.
►System Opt.
3) Press ▼ to select “System Opt.” and then press
OK.
System Opt. ↓
►Date Time
Language English
FPCard Key
4) Press OK to select "Date Time".
YYYYMMDD 24H
20090101
9:34:29
ESC OK
5) To modify date or time, press ▲/▼ to move the cursor to the desired option, and then press ▲/▼ again to enter correct date or time. Press OK to save your settings.
@
Note: You can set the date between January 1 st
2003 and December 31 st
2032.
To set the date beyond this range, you need to consult our commercial representatives or presales technical support engineers.
12
Fingerprint Lock User Manual V1.0.1
2. Enrollment and Verification
2.1 Enroll an Administrator
If the fingerprint lock has no administrator, you must at least enroll one administrator before enrolling ordinary users. To enroll an administrator, proceed as follows:
20091124
FP LOCK
1) Power on the fingerprint lock by pressing the
Start key to open up the initial interface. Press and hold the Menu key to display the menu interface.
Menu
►User Manage
Options
PenDrive Mng
↓
2) Press OK to display the user management interface.
User Manage
Enroll User
FPCard Mng
►Admin Cnt
↓
3) Press ▼ to select “Admin Cnt” and then press
OK.
After that, the enrolled administrator can perform fingerprint, password and RF card enrollment.
13
Fingerprint Lock User Manual V1.0.1
2.1.1 Enroll a Fingerprint
Enroll Admin
►Enroll FP
Enroll Pwd
Reg RFID
↓
4) Press ▼ to select “Enroll FP” and then press OK.
Admin Accredit
Supervisor
ESC OK
5) Press ▲/▼ to select “Admin Accredit”, and then select “Supervisor” (Super administrator) or
“Admin” (Administrator). Press OK to confirm your selection.
Enroll FP
New Enroll?
ESC OK
6) Press OK to continue.
New Enroll
ESC
UserID 00001
000010
Place Finger…
ESC
OK
7) The system by default assigns unused user IDs from 00001 and you may also manually enter an unused user ID.
This meter is used to indicate the successful fingerprint enrollment times
One white bar turns black each time when you enroll a fingerprint successfully.
8) Press the same finger on the fingerprint sensor three consecutive times by adopting the proper finger placement mode. The system will prompt you to save the enrollment information after you enroll the fingerprint successfully. If enrollment fails, the system will prompt you to reenroll your fingerprint.
14
Fingerprint Lock User Manual V1.0.1
The system returns to the “New Enroll” interface upon successful enrollment. You can continue or exit the fingerprint enrollment.
@
Note: The last digit in “00001–0” refers to the fingerprint count. “0” refers to the first fingerprint, “1” refers to the second fingerprint and so on and so forth.
2.1.2 Enroll a Password
Enroll Admin
Enroll FP
►Enroll Pwd
Reg RFID
↓
4) Press ▼ to select “Enroll Pwd” and then press
OK.
Admin Accredit
Supervisor
ESC OK
5) Press ▲/▼ to select “Admin Accredit”, and then select “Supervisor” (Super administrator) or
“Admin” (Administrator). Press OK to confirm your selection.
Enroll FP
New Enroll?
ESC OK
6) Press OK to continue.
New Enroll
UserID 00001
ESC OK
7) The system by default assigns unused user IDs from 00001 and you may also manually enter an unused user ID.
15
Fingerprint Lock User Manual V1.0.1
New Enroll
————
8) Input a password by pressing the number keys and press OK to confirm your input.
New Enroll
******
—
9) Input the password again by pressing the number keys and press OK to confirm your input. Press OK after successful password enrollment to return to the
“New Enroll” interface.
New Enroll
00001P
ESC OK
10) Press OK to save the enrolled data and exit the password enrollment.
@
Note: A password consists of 6 to 10 digits. You can enroll only one password for each user ID and repeated passwords are allowed; otherwise, the system will display the prompt “Password Error”.
2.1.3 Enroll an RF ID Card
@
Note: This function is only provided by fingerprint locks that support the RF
ID card function.
16
Fingerprint Lock User Manual V1.0.1
Enroll Admin
Enroll FP
Enroll Pwd
►Reg RFID
↑
4) Select “Reg RFID” and press OK.
Admin Accredit
ESC
Supervisor
OK
5) Press ▲/▼ to select “Admin Accredit”, and then select “Supervisor” (Super administrator) or “Admin”
(Administrator). Press OK to confirm your selection, as shown in the figure on the left.
Reg RFID
New Enroll?
ESC OK
6) Press OK to proceed to the next step. The interface displayed is shown in the figure on the left.
New Enroll
UserID: 00010
ESC OK
7) Enter the ID (ranging between 1 and 65534) to be enrolled behind the “UserID” option, and press OK, as shown in the figure on the left:
New Enroll
Show the card
UserID: 00010
ESC OK
8) Show the card by following the prompt, as shown in the figure on the left:
17
Fingerprint Lock User Manual V1.0.1
New Enroll
CARD: 16650449
UserID: 00010
ESC OK
9) The displayed card number is shown in the figure on the left.
New Enroll
000010C
ESC OK
10) Press OK to proceed to the next step. The interface displayed is shown in the figure on the left.
Note: The last letter “C” in “00010C” refers to the ID card.
11) Press OK to save the enrolled data and exit the ID card enrollment.
2.2 Enroll an Ordinary User
An administrator can enroll only ordinary users, with operation steps as follows:
20091124
FP LOCK
1) Power on the fingerprint lock by pressing the
Start key to open up the initial interface.
Admin Confirm
FP LOCK
2) Press and hold the Menu key to access the menu options. The system will then prompt you for administrator confirmation. Enter the administrator password or match your fingerprint once. Skip to step 4 if verification succeeds; otherwise, proceed to step 3.
18
Fingerprint Lock User Manual V1.0.1
Error Pwd.
3) The system displays the prompt “Error Pwd.” on the screen and return to the “Admin Affirm” interface for reverification. The following menu interface is displayed upon successful verification.
Menu
►User Manage
Options
PenDrive Mng
↓
4) Press OK to display the user management interface.
User Manage
►Enroll User
FPCard Mng
Enroll Admin
↓
5) Press ▼ to select “Enroll User” and then press
OK.
After that, the enrolled administrator can perform fingerprint, password and RFID card enrollment. The rest operation steps are basically the same with those of administrator enrollment except that you do not have to select the administrator privileges. For details, see 2.1 Enroll an Administrator.
19
Fingerprint Lock User Manual V1.0.1
2.3 Backup Enrollment
On the "New Enroll?" interface, if you press ESC to cancel new enrollment, then the
“Backup Enroll” interface will be displayed, as shown in the figure on the right.
Enroll FP
Press ESC
Backup Enroll
UserID 00009
ESC
New Enroll?
OK ESC OK
The backup enrollment steps are basically consistent with the new enrollment steps except that “Backup Enroll” instead of “New Enroll” is displayed on the top of the interface.
@
Note: 1. It is a wise choice to enroll fingerprints of at least two different fingers for longstanding users.
2. If you wish to modify the password after finishing password enrollment, you can replace the original password with the password entered in backup enrollment.
3. If you perform backup enrollment after enrolling the RFID card, the original RFID card number will be replaced by the ID card number
entered in backup enrollment.
20
Fingerprint Lock User Manual V1.0.1
2.4 Set User Verification and NO Status
20091124
FP LOCK
1) Press the Start key to display the initial interface.
The fingerprint sensor is in active state.
UserID 00001
Normal Open
ESC OK
2) Press your finger with fingerprint already enrolled or enter your password (press OK after entering password.)
Note: You can only match fingerprints when the fingerprint lock is in nonNO state.
3) Your ID number will be displayed on the screen upon successful verification and then you can hear the unlocking sound. Rotate the handle of the fingerprint lock within 4 seconds to open the door.
If the NO function is set to “YES” (See 3.1), the prompts as shown in step 4 and step 5 will be displayed upon successful verification; otherwise, no prompt will be displayed.
4) If you press ESC when the system prompts whether to set the NO function, the fingerprint lock will be automatically locked. The “Unlocking” icon on the screen will change into the “Locking” icon and the system automatically powers off.
21
Fingerprint Lock User Manual V1.0.1
Normal Open
5) If you press OK, the interface as shown in the figure on the left will be displayed, indicating successful NO setting. In the meantime, the buzzer will beep three consecutive times.
If fingerprint or password verification is unsuccessful, the system will display a prompt “Please press your finger again” or “Password error”. The parameters
“Illegal Cnt.” and “Illegal Alarm” are set by the administrator. The system will generate an alarm after the illegal operations reach the specified value. For details, see 3.1.
@
Note: If the value of the parameter “Illegal Cnt.” is larger than 6, the system will automatically power off if you fail to verify your fingerprint or password
6 consecutive times.
2.5 FP Card Management *
@
Note: 1) This function is only provided by fingerprint locks that support the
Mifare card function.
2) If no administrator is enrolled in the system, the system will prompt you to enroll an administrator first.
Select “FPCard Mng” from the “User Manage” interface, as shown below:
FPCard Mng
Create PINCard
Enroll FPCard
Create FPCard
Empty Card
22
Fingerprint Lock User Manual V1.0.1
Create PINCard: This option is used to create an ID card for a user who has already been enrolled in the fingerprint lock. You can verify your ID card instead of your fingerprint (only after the parameter “Card Only” is set to “Yes”. For details, see 3.1).
Enroll FPCard: This option is used to store an enrolled fingerprint directly in the
FP card instead of in the fingerprint lock. You can verify user identify in the form of “FP card + fingerprint”, that is, swipe the
FP card before pressing the finger.
Create FPCard: This option is used to duplicate the enrolled fingerprints (stored in the fingerprint lock) to the FP card. You can verify user identity either through the “Fingerprint” or in the form of “FP card + fingerprint”.
Empty Card: This option is used to purge all data (fingerprints and numbers) stored in the FP card.
2.5.1 Create a PIN Card
1. Create a PIN Card
Every user will be assigned with an ID number, for example, 00001, after users are enrolled in the fingerprint lock.
Create PINCard
UserID 00001
ESC OK
1) Select “User Manage” à “FPCard Mng” à
“Create PINCard” from the main menu. The interface as shown in the figure on the left is displayed:
23
Create PINCard
Show the card
Fingerprint Lock User Manual V1.0.1
2) When prompted to enter the user ID number, press ▲/▼ to select the desired user ID, and press
OK. The system then prompts you to “Show the card” (If the selected user ID does not exist in the system, the system will display a prompt “No
Enroll”), as shown in the figure on the left:
Create PINCard
Write succ
3) Swipe your FP card through the card reader. l The interface as shown in the figure on the left is displayed:
If the system gives a prompt “Write succ”, your
PIN card is successfully created. You can replace the fingerprint verification with the PIN card verification.
Create PINCard
Write failed 7 l If the interface as shown in the figure on the left is displayed: you PIN card is not written in the system. “7” means write error.
@
Note: To create a PIN card, you need to ensure the user ID has already existed in the system; otherwise, the system will display a prompt “No Enroll” and you need to repeat the operation. After the PIN card is successfully created, only the ID number is stored in the PIN card.
24
Fingerprint Lock User Manual V1.0.1
2 Verify the PIN Card
@
Note: Set the parameter “Card Only” to “Yes”. If you set the parameter “Card
Only” to “No”, you cannot verify with the created PIN card.
Set Opt.
Verify Mode
Normal Open Yes
Card Only No
1
1) Select “Set” à “Set Opt.” from the main menu.
The interface as shown in the figure on the left is displayed:
Set Opt.
ESC
Save?
OK(Save)
2) Select “Card Only” and press OK. Then press
▲/▼ to select “Yes”. Press OK to save the setting.
Then, you can perform PIN card verification.
UserID 00001
3) Swipe your PIN card through the card reader when the system returns to the initial interface. If the interface as shown in the figure on the left is displayed, the PIN card is successfully created.
2.5.2 Enroll an FP Card
1. Enroll an FP card
Enroll FPCard
UserID: 00003
ESC OK
1) Select “User Manage” à “FPCard Mng” à
“Enroll FPCard” from the main menu to display the interface as shown in the figure on the left:
25
Fingerprint Lock User Manual V1.0.1
Enroll FPCard
000030
Place Finger…
ESC
Enroll FPCard
000030
Second Press
ESC
2) Press ▲/▼ to select an ID and then press OK to confirm your selection and proceed to the next step.
Place one of your fingers on the fingerprint sensor.
3) Place the same finger on the fingerprint sensor again.
Enroll FPCard
000030
Third Press
ESC
Enroll FPCard
00003: 1
Show the card
4) Place the same finger on the fingerprint sensor for the third time.
The interface as shown in the figure on the left is displayed:
Enroll FPCard
00003: 1
Write succ
5) Swipe your card through the card reader until the interface as shown in the figure on the left is displayed.
Now the FP card is enrolled successfully.
2. Verify an enrolled FP card
Note: Please set the “Card Only” option to No. If you set it to Yes, the fingerprint lock will only verify users’ PIN cards.
26
Fingerprint Lock User Manual V1.0.1
00003
Place Finger…
1) On the initial interface, swipe an enrolled FP card through the card reader. The interface as shown in the figure on the left is displayed:
UserID: 00003
2) Place one of your fingers with fingerprint enrolled on the fingerprint sensor window properly.
When the interface as shown in the figure on the left is displayed, the FP card passes the verification successfully.
@
Tip: Through the above operations, you only store your fingerprints in your FP card but not in the fingerprint lock. Therefore, you must show your FP card first before fingerprint comparison. (Your fingerprints are only stored in your
FP card.)
2.5.3 Create an FP Card
1. Create an FP card
Every user is allocated with an ID, for example, 00003, during the enrollment of fingerprint.
Create FPCard
UserID
ESC
00003
OK
1) Select “User Manage” à “FPCard Mng” à
“Create FPCard” from the main menu to display the interface as shown in the figure on the left:
27
Fingerprint Lock User Manual V1.0.1
Create FPCard
Show the card
2) Press OK and the interface as shown in the figure on the left is displayed.
Create FPCard
Write succ
3) Swipe your card through the card reader until the interface as shown in the figure on the left is displayed.
Now an FP card is created successfully.
2. Verify a created FP card
Note: Please set the “Card Only” option to No.
The operations of verifying a created FP card is the same with that of verifying an enrolled FP card.
@
Tip: Through the above operations, you can duplicate fingerprints from the fingerprint lock to an FP card. In this way, you can perform identification either through fingerprint or “FP card + fingerprint“. (Your fingerprints are stored in both the fingerprint lock and your FP card.)
2.5.4 Purge an FP Card
To purge all the information in an FP card, proceed as follows:
Empty Card
Show the card
1) Select “User Manage” à “FPCard Mng” à
“Empty Card” from the main menu to display the interface as shown in the figure on the left:
28
Fingerprint Lock User Manual V1.0.1
Empty Card
Write succ
2) Swipe your card through the card reader until the interface as shown in the figure on the left is displayed.
Now the FP card is purged successfully.
2.6 Delete User Data
Warning:
It is prohibited to power off the fingerprint lock while deleting user data so as
to prevent the program from accidentally deleting other data.
To delete user data, proceed as follows:
20091124
FP LOCK
1) Press the start key to power on the fingerprint lock and then enter the initial interface.
Admin Confirm
FP LOCK
2) Enter the administrator password or fingerprint once. If the verification succeeds, jump to Step 4; otherwise, go to Step 3.
29
Error Pwd.
Fingerprint Lock User Manual V1.0.1
3) The system displays the prompt “Error Pwd.” on the screen and returns to the “Admin Affirm” interface for reverification. If you pass the verification, you can access the “Menu” interface.
Menu
►User Manage
Options
PenDrive Mng
↓
4) Press OK to display the “User Manage” interface.
User Manage
FPCard Mng
Enroll Admin
►Delete
↑
5) Press ▼ to select “Delete”, and press OK.
Delete
UserID 00002
ESC OK
6) Press ▲/▼ to select the user ID that you want to delete and then press OK to confirm your selection.
Del Fingerprint
00002—0
ESC OK
If the user has enrolled his/her fingerprints,
7) Press OK to delete the fingerprints.
ESC
Del Password
00002—P
OK
If the user has enrolled a password,
8) Press OK to delete the password.
30
Fingerprint Lock User Manual V1.0.1
ESC
Del User
00002
OK
9) Confirm the deletion of this user. Press OK to confirm the deletion, or press ESC to return to the
“User Manage” interface.
10) After deleting the user data, you can restart the fingerprint lock and match the deleted fingerprints again to check whether the user data is deleted for sure.
@
Note: The administrators (including super administrators) can delete only ordinary users. To delete an administrator ID, you need to select
"Options" à "System Opt." à "Adv Option" à "Clr Admin Pri", and
then select “User Manage” à "Delete” to delete the ID.
31
Fingerprint Lock User Manual V1.0.1
3. Lock Function Information and Settings
3.1 Operation Settings
Select "Options" à "Set Opt.” from the main menu to display the following information:
Set Opt.
Illega Alarm Yes
Illega Cnt. 10
Lock 5
Verify Mode 1
Normal Open Yes
Card Only No
The options under “Set Opt.” include: Illega Alarm, Illega Cnt., Lock, Verify
Mode, Normal Open, and Card Only.
Illega Alarm (Illegal Alarm): The fingerprint lock will power off automatically when the number of consecutive operation failures exceeds the set value. After restart, its buzzer will sound discontinuously for 30 seconds to generate an invalid operation alarm and then power off automatically.
Illega Cnt. (Illegal Operation Count): This parameter is used to set the consecutive operation failure count. An invalid operation alarm will be generated when the consecutive failure count exceeds the threshold. Value range: 3–99. Default value: 10.
@
The failure count is cumulated when the fingerprint lock is started next time. If the number of cumulative failures exceeds the threshold, the fingerprint lock will generate an invalid operation alarm; otherwise, the failure count will no longer be accumulated after successful unlocking.
32
Fingerprint Lock User Manual V1.0.1
Lock: This parameter is used to set the duration from successful matching to unlocking. Select Lock and press OK to display the Lock interface. Press ▲/▼ to select a value. Press ESC to exit current interface and save your settings. For this parameter, its unit of quantity is 1 second and value range is 3–15, that is, 3–15 seconds.
@
Note: The unit of quantity and the maximum value of this parameter here are standard configurations. If you need larger parameter values, please consult our commercial representatives or presales technical support engineers.
Verify Mode: Press OK to display the Verify Mode interface, and press ▲/▼ to select a value. There are three optional values 0, 1, and 2 that represent different matching modes respectively, and the default value is 1.
Verify Mode 0: Only the administrator can open the lock, while the unlocking function is disabled for ordinary users.
Verify Mode 1: This is a default matching mode. Users can open the lock by successfully matching their fingerprints only once.
Verify Mode 2: This is a dual verification mode. The administrator can open the lock by successfully matching his/her fingerprint only once, but an ordinary user has to pass the verification in any two matching modes by using the same ID.
Normal Open: Press OK to display the Normal Open interface, and press ▲/▼ to select Yes or No. If you select Yes, a prompt will be displayed after unlocking, inquiring whether you desire to select Normal Open. If you press OK, the system will prompt you that the NO function is enabled and then power off automatically and immediately. The
Normal Open interface is shown as follows:
33
Fingerprint Lock User Manual V1.0.1
20091116
Card Only:
ESC OK(Lock Up)
To disable the NO function, power on the system and press OK in the Normal Open interface. Then the system closes the lock and automatically powers off.
Press OK to display the Card Only interface, and press ▲/▼ to select Yes or No. If you select Yes, you only need to verify your ID card. +If you select No, you need to verify both your ID card and fingerprint.
3.2 Language Settings
Select "Options" à "System Opt." à "Language" from the main menu to display the following information:
System Opt.
Date Time
►Language
FPCard Key
English
↓
Press OK to display the Language interface, and press ▲/▼ to select a desired language. Press OK to confirm your settings and then press ESC to exit System Opt.
When the system prompts whether to save your settings, press OK and your settings will take effect after system restart.
34
Fingerprint Lock User Manual V1.0.1
@
Note: Language selection is a nonstandard function. If you need this function, please consult our commercial representatives or presales technical support engineers.
3.3 FP Card Password
After you set a password for your FP card, the fingerprint lock will write this password into a Mifare card during the enrollment or creation of your FP card.
Select "Options" à "System Opt." à "FPCard Key" from the main menu to display the following information:
FPCard Key
000000
ESC OK
The FP card password consists of 6 digits. To enter a password, first select a digit from 0–9 by pressing á or â (You can press and hold á or â to rapidly scroll through the 10 digits) and press OK to confirm it. Then input the next digit in the same way until the last one. Finally, press OK to confirm the password and return to the System Opt. menu.
3.4 Advanced Settings
@
Note: Only the super administrator has the right to perform advanced settings.
Select "Options" à "System Opt." à "Adv Option" from the main menu to display the following information:
35
Fingerprint Lock User Manual V1.0.1
Adv Option
Reset Opts.
Del All Logs
Clear All Data
↓ Clr Admin Pri
The options under “Adv Option” include: Reset Opts., Del All Logs, Clear All
Data, and Clr Admin Pri. Select any one of these options and press OK to display the related setting interface. Press OK according to the prompt to confirm your settings and return to the Adv Option interface, or press ESC to exit current interface without performing any operation.
Reset Opts.: This parameter is used to restore the fingerprint lock to factory defaults.
Del All Logs: This parameter is used to delete all the verification records from a memory chip.
Clear All Data: This parameter is used to delete all the enrolled fingerprint images, passwords and records.
Clr Admin Pri: This parameter is used to change an administrator into an ordinary user. This function shall be used with caution. It is recommended to register at least one new administrator in time after clearing the priority of an administrator.
3.5 Browse System Information
Users can browse all the system information, including the enrolled fingerprint counts, enrolled user, and device information. Select “Sys Info” from the main menu, and press OK to proceed to the next step and display the following information:
36
Fingerprint Lock User Manual V1.0.1
Sys Info
Browse Logs
Enroll User
Enroll FP
5
1
↓
Log
Admin Cnt
Pwd Usr
Reg RFID
Free Space Info
Dev Info
85
2
3
12
Press ▲/▼ to select Free Space Info and then press OK to browse the following information:
Free Space Info
FP Cnt 499
Log 29915
Reg RFID 488
@
Note: Only the fingerprint locks supporting ID cards are configured with the
“Reg FPID” and “Free Space Info” options.
Press ▲/▼ to select Dev Info and then press OK to browse the following information:
Dev Info
FPCnt(100) 5
Log(10k)
Manu Time
↓
3
Serial Num
Vendor
Device Name
Alg Version
Firmware Ver
3.6 Browse Logs
The fingerprint locks support the offline browsing of unlocking logs, which facilitates users to check whether there is any exceptional unlocking in time.
37
Fingerprint Lock User Manual V1.0.1
Select “Browse Logs” from the main menu to display the following information:
Browse Logs
UserID
ESC
0001
OK
Press ▲/▼ to select a registered number that you want to browse logs and then press OK to confirm the log date and time:
21
PIN: 0001
20090405 14: 49
ESC OK
The first digit denotes the total number of records and the last one denotes current record.
3.7 USB Pen Drive Management
USB interface
1) Insert a USB pen drive into the USB interface.
ESC
PenDrive Mng?
OK
2) Select “PenDrive Mng” from the main menu and press OK. A prompt as shown below is displayed.
38
PenDrive Mng
DwnLoad AttLog
DwnLoad User
UpLoad User
Upgrade Firmware
Fingerprint Lock User Manual V1.0.1
3) Press OK in the prompt dialog box to display the following interface:
1. Download Attendance Logs
Copy Data Suc!
1) Press ▲/▼ to select “Dwn AttLog” and then press
OK. When download completes, the following interface is displayed:
2) Press ESC to return to the initial interface and then remove the USB pen drive.
Now the USB pen drive stores two files: X_attlog.dat (attendance logs) and X_user
(where "X" denotes that the device No. is X).
@
Tip: If the download succeeds, a prompt “Copy Data Suc” will pop up. If the system displays the prompt “Plug Pen Drive?”, please check whether the USB pen drive is plugged in properly.
2. Download User Data
User data downloading is similar to the downloading of attendance logs. Press ▲/▼ to select “DwnLoad User” from the “PenDrive Mng” menu. The files user.dat (user information) and template.dat (fingerprint template) will be concurrently downloaded to the USB pen drive.
3. Upload User Data
Press ▲/▼ to select “UpLoad User” from the “PenDrive Mng” menu and then press
OK. The files user.dat (user information) and template.dat (fingerprint template) stored in the USB pen drive will be concurrently uploaded to the fingerprint lock.
39
Fingerprint Lock User Manual V1.0.1
@
Tip: If a user exits with the same ID in the fingerprint lock, the new upload will overwrite the existing user data; otherwise, the new user data will be directly added.
4. Upgrade Firmware
You can select “Upd Firmware” to upgrade the firmware of a fingerprint lock through the upgrade files in the USB pen drive.
@
Note: If you need firmware upgrade files, please contact our technical support engineers. Generally it is not recommended to upgrade the firmware.
Tip: Please do not perform invalid operations (for example, insert or remove the USB pen drive in a frequent manner or during upload/download) on the USB pen drive, because it may result in system instability. It is recommended to keep the door open during the use of the USB pen drive.
40
Fingerprint Lock User Manual V1.0.1
4. Conventions on Other Functions
4.1 Routine Operation Indications
User operation success indication: The buzzer sounds once and the green LED indicator is solid on for 3 seconds.
User operation failure indication: The buzzer sounds short tone twice and the red
LED indicator is solid on for 3 seconds.
Warning indication: The buzzer sounds short tone five times intermittently.
4.2 Administrator Loss Prevention
To avoid the menu operation failure as a result of loss of administrator, you may take the following measures: Press and hold the Menu key for 3 seconds to display the administrator verification interface. Then move the band switch on the rear of the fingerprint lock to the left or right. Now you can access the menus as super administrator for management and operation.
4.3 Battery Low Voltage Protection
Low Voltage Protection: When the battery meter stays at one bar, the system prompts you to replace the battery and the battery icon starts flashing. If you press and hold the Menu key, the system prompts you that you cannot access menus. In addition, the menus are also inaccessible during use of external power so as to prevent data loss caused by power instability. When the battery meter stays less than one bar, the battery shuts itself off automatically.
41
Fingerprint Lock User Manual V1.0.1
4.4 Automatic Program Exit and System Poweroff
n The fingerprint lock powers off automatically upon successful matching and unlocking. n The fingerprint lock powers off automatically when you set Yes for the
“Normal Open” option upon unlocking. n The fingerprint lock powers off automatically when the number of invalid operations exceeds the threshold. The fingerprint lock powers off automatically when an alarm is generated for 30 seconds upon restart. n The fingerprint lock powers off automatically when the supply voltage is lower than level3 detection voltage. n The fingerprint lock powers off automatically if there is no keystroke within
10 seconds on the initial interface.
4.5 External Power Use Description
The fingerprint lock supports temporary use of external DC power for fingerprint or password matching and unlocking, but when connected with an external battery, the fingerprint lock cannot provide such special functions as enrollment, deletion and setting, so as to prevent data loss as a result of power instability.
As shown in the figure below, connect a 9V battery to the two access points at the bottom of a fingerprint lock, regardless of polarity.
42
Fingerprint Lock User Manual V1.0.1
If you power off a fingerprint lock without closing the lock during the use of external power, the lock cylinder will not automatically return to its original position.
That is, the fingerprint lock remains in NO state. To solve this problem, you can replace the battery and then open the lock once to have the lock cylinder in position.
4.6 Unlock With an Emergency Mechanical Key
You can open the door using an emergency mechanical key in case the electronic component does not operate.
(1) Pry open the keyhole cover by inserting the sharp end of a ballpen or screwdriver with a diameter of less than 3 mm. Remove the cover.
(2) Insert the emergency key into the keyhole and rotate 90° to unlock.
43
①
Fingerprint Lock User Manual V1.0.1
②
44
Fingerprint Lock User Manual V1.0.1
Appendix
Technical Specifications
Ø Display ：OLED display
Ø Sensor: Optics sensor without coating
Ø Capacity: 500 fingerprint images; 100 passwords; 500 users.
Ø Matching mode: Fingerprint only , password only, MF card only, ID card only, combination of fingerprint and matching password, combination of fingerprint and matching card.
Ø Record capacity: 30000
Ø Communication：USB Flash Disk
Ø Resolution: 500 DPI
Ø Identification speed: ≤ 2 seconds
Ø False acceptance rate: ≤ 0.0001%
Ø False rejection rate: ≤ 1%
Ø Power: Four AA batteries; working voltage: 4.2V–6V.
Ø Locking count: ≥ 4000 (Four NANFU alkaline batteries)
Ø Temperature: 0–45°C
Ø Humidity: 10%–80%
45
This document is subject to change without prior notice.
Printed in China
Advertisement
Key Features
- Fingerprint + password unlocking
- OLED display
- Classified privileges
- Data deletion
- Firmware upgrade
- Offline logs
- Battery low voltage protection
- Emergency mechanical key
