TFT Serials User Manual

TFT Serials User Manual
DS100 User Manual
Version: 1.0
Date: Feb. 2011
Introduction:
This document mainly introduces the windows and operations of DS100 dual FP
reader device.
TFT Serials User Manual
About this manual

Not all the devices have the function with ★. The real product prevails.

The photograph in this manual may be different from that of the real product.
The real product prevails.
Table of Contents
Table of Contents
1. Operating Instruction........................................................................ 1
1.1 Abbreviated Operating Procedures ............................................................. 1
1.2 How to Press the Fingerprint ...................................................................... 2
1.3 About Attendance ....................................................................................... 3
1.3.1 Select Attendance State .................................................................. 3
1.3.2 Identity Verification........................................................................ 4
1.4 Connection with Computer......................................................................... 9
1.5 Main Menu ............................................................................................... 10
2. User Management ............................................................................ 12
2.1 Add a New User ....................................................................................... 12
2.2 User Management..................................................................................... 15
2.2.1 Search User .................................................................................. 16
2.2.2 Query Attendance Record ............................................................ 17
2.2.3 Edit User ...................................................................................... 18
2.2.4 Delete User ................................................................................... 19
2.2.5 Add User ...................................................................................... 20
2.3 SMS.......................................................................................................... 20
2.3.1 Set SMS ....................................................................................... 21
2.3.2 Employee Check SMS ................................................................. 22
2.4 Card Management ★ .............................................................................. 25
2.4.1 Enroll Card ................................................................................... 25
2.4.2 Enroll Fingerprint Card ................................................................ 26
2.4.3 Clear Card Information ................................................................ 28
2.4.4 Copy Card Information ................................................................ 29
2.4.5 Card Setting.................................................................................. 29
3. Communication Settings ................................................................. 31
3.1 Network Option ........................................................................................ 31
3.2 Serial Port Option ..................................................................................... 32
I
TFT Serials User Manual
3.3 Connection Option ................................................................................... 33
3.4 Wireless Option ★ .................................................................................. 34
3.5 Wireless Network ★ ............................................................................... 37
4. System Option .................................................................................. 38
4.1 System Parameter ..................................................................................... 38
4.2 Data Management..................................................................................... 40
4.3 Upgrade Firmware .................................................................................... 41
4.4 Keyboard Definition ................................................................................. 41
4.4.1 Set Shortcut .................................................................................. 42
4.4.2 Use Shortcut ................................................................................. 43
4.5 Interface Option........................................................................................ 44
4.6 Reset ......................................................................................................... 45
4.7 Bell Option ............................................................................................... 46
4.8 Other Options ........................................................................................... 47
5. Time Date ......................................................................................... 49
5.1 Time Date Option ..................................................................................... 49
5.2 DLST ........................................................................................................ 49
6. U Disk Management ........................................................................ 51
6.1 Download by U-disk ................................................................................ 51
6.2 Upload by U-disk ..................................................................................... 52
6.3 Download to SD Card .............................................................................. 53
6.4 Upload by SD Card .................................................................................. 54
7. Auto Test ........................................................................................... 56
7.1 TFT Test ................................................................................................... 56
7.2 Audio Test ................................................................................................ 56
7.3 Keyboard Test........................................................................................... 56
7.4 Sensor Test ............................................................................................... 57
7.5 Real-time Clock........................................................................................ 57
8. Query Record ................................................................................... 58
II
Table of Contents
9. System Information ......................................................................... 60
9.1 Record Capacity ....................................................................................... 60
9.2 Device Information................................................................................... 60
10. Appendix......................................................................................... 61
10.1 Keyboard ................................................................................................ 61
10.2 USB ........................................................................................................ 62
10.3 Time Ring ............................................................................................... 62
10.4 T9 Input Method ..................................................................................... 63
10.5 Quick Query of Attendance Record ........................................................ 65
10.6 Propaganda Picture Upload Rules .......................................................... 65
10.7 Short Message Management ................................................................... 66
10.8 Mifare Card ★ ...................................................................................... 67
10.9 9 Digit Code ........................................................................................... 68
10.10 Daylight Saving Time ........................................................................... 68
10.11 WiFi Software Using Instruction ★ .................................................... 69
10.12 Photo ID Function ................................................................................ 71
10.13 Backup Battery ..................................................................................... 72
10.14 About the Human Rights Privacy Statement ........................................ 73
10.15 Environmental Protection ..................................................................... 75
III
1. Operating Instruction
1. Operating Instruction
1.1 Abbreviated Operating Procedures
Step 1: Install the device and power it up.
Step 2: Enroll users by registering his/her fingerprints, passwords or card. Assign
users‟ security privileges directly on the device.
Step 3: After enrolling users, verify that his/her enrolled fingerprint, passwords or
card is valid.
Step 4: Configure the device communication settings. Then download the users‟
newly enrolled information from the device onto the Attendance Management
Software on the computer. Data can be transmitted via TCP/IP or USB client or by
using a USB flash drive or a SD memory card.
Step 5: Verify the device displays the correct day and time. Then start to attendance.
Step 6: Download attendance records to the Attendance Management and stat them
at the end of the month.
1
TFT Serials User Manual
1.2 How to Press the Fingerprint
Enroll fingerprint by pressing index finger, middle finger or ring finger (thumb and
little finger are clumsy).
1)
Proper press:
Make finger center pressed on
the sensor window
2)
Improper press:
Upright
Too lean
Slant
Too downward
Please adopt the correct way to place the finger to avoid improper
operation led to the identification performance degradation.
2
1. Operating Instruction
1.3 About Attendance
When the device is in standby status, only after successful fingerprint or password
verification, can user save attendance record on the device.
Standby status is as shown below:
The picture displayed in standby status can be uploaded by user (please refer to 6 U
Disk Management). It can also be time display (refer to 4.5 Interface Option)
1.3.1 Select Attendance State
Mode 1:
When the device is in standby status, press state key on the device to modify
attendance state, and the state information will be displayed on the screen. The
current selected state is displayed in orange. Refer to 4.4 Keyboard Definition for
default state key definition.
3
TFT Serials User Manual
Mode 2:
Various states can be set by user. Only the corresponding states come out on the left
bottom corner.
1.3.2 Identity Verification
After successful user verification, the device will return to the initial interface. For
dual FP reader device, the attendance result displays on either side of screen (left or
right side of screen, with the same size). The keyboard input displays on any side of
the screen according to the user‟s requirements. And the fingerprint, PIN and card
verification displays on the same side with keyboard input (*the following
demonstration is using the left side of screen to display). Two of the FP reader can
be used by the same time.
1. Fingerprint Matching
(1) 1:N fingerprint matching
Verify the fingerprint pressed on the reader at present with all fingerprint data in the
fingerprint reader. Two of the FP reader can be used by the same time. And the
attendance result will displays on left screen.
Step 1: Press fingerprint properly on the reader.
Step 2: If the device says „Thank you”, the verification is complete.
Use the left FP reader:
4
1. Operating Instruction
Use the right FP reader:
Both FP reader in used:
(2) 1:1 fingerprint match (User ID + fingerprint)
Verify the fingerprint pressed on the reader at present with the fingerprint related
with user number. Use this method when it is difficult to identify user‟s fingerprint.
5
TFT Serials User Manual
Step 1: Input User ID of employee to be verified on the initial interface.
Step 2: Press fingerprint properly on the reader.
Step 3: If the device says „Thank you”, the verification is complete.
If you press the finger on the left FP reader, it is 1:1 fingerprint verification, and the
verified result displays on the left side of the screen.
If you press the finger on the right FP reader, it is the 1:N fingerprint verification
(for any user to verify).
6
1. Operating Instruction
If the device says “Please try again”, return to step 2 for second operation. Employee
can try another 2 times by default. The repeated times can be set in 4.5 Interface
Option. If it fails after 2 times, return to step 1 directly.
2. Password Matching
Step 1: Input User ID of employee to be verified on the initial interface. Then press
OK.
Step 2: If it displays Error ID. NO, it means that there is no such number. If it
prompt to press finger, that the employee doesn‟t enroll password.
Step3: Input password and press OK.
If you input the right user password, it is the password verification, the result will
display on the left side of the screen.
7
TFT Serials User Manual
If you press the finger on either FP reader, it is the 1:N fingerprint verification and
the result will display on the right side of the screen (for any user to verify).
When the device displays “password error”, you need to input the password again.
Employee can try another 2 times by default. The repeated times can be set in 4.5
Interface Option. If it fails after 2 times, return step 1 directly.
3. Card Matching ★
Step 1: Wave the card near to the card sensor area, after the device find the card,
removes the card.
Step 2: When the device says "Thank you", the certification completed.
8
1. Operating Instruction
The card verification and FP verification can be used by the same time. The
verification result displays as the following figure.
Step 3: If the card has not registered yet, it will prompt that the card is not
registered.
1.4 Connection with Computer
The device only records attendance time. After that the data can be processed by
software on computer. Therefore, it is necessary for the device to connect with a
computer, to download the attendance record or upload the user data and so on.
The following are some connection method:
1. Ethernet:
Through hub: Use the net cable to connect the device and computer to the same
network.
9
TFT Serials User Manual
Direct connection: Use the cross cable to connect the device and the computer
directly).
Set device: Enter Menu -> Option -> Communication Option to set the following
items:
IP address: Default IP as 192.168.1.201. You can modify it if it is necessary.
Subnet mask: Default subnet mask as 255.255.255.0. You can modify it if it is
necessary.
Gateway address: Default gateway address0.0.0.0. You can modify it if it is
necessary.
Network speed: There are three options: ATUO, 10M, and 100M.
Connection password: It can be set or not set. If it is set, input corresponding
numerical value on connection interface of computer software.
2. USB ★
Set device: Enter Menu -> Option -> Communication option to set the following
items:
Device ID: Set it in “connection option”. The number can be selected from 1-254.
USB: Select “Yes” for USB communication.
Communication password: Set it in “connection option”. It can be set or not set. If
it is set, input corresponding numerical value on connection interface of computer
software.
1.5 Main Menu
Start at the device, and long press the Menu key to open the Main Menu, as shown
in the following figure:
10
1. Operating Instruction
User Management: Browse the users‟ basic information like ID, name, fingerprint,
card, password and privilege and so on; Increase, edit or delete operation the basic
information, and the card management.
Communication: Set up communication parameters between the equipment and the
computer, including IP address, gateway, subnet mask, baud rate, device number,
communications password etc.
System: Manage the data and set the system parameters, including basic parameters,
interface parameters, fingerprint and attendance parameters, to maximize meet
user‟s needs in the functional, display and other areas.
Date/Time: Device time date should set accurate to ensure the accurate attendance
time.
Pen Drive: By USB or SD card, the user info and attendance data etc. can be
imported to the accordingly software to deal or import the user information for other
fingerprint devices to use.
Auto Test: Automatically test the function of each module if it is workable,
including the screen, reader, voice, keyboard and clock.
Record: For query the record saved in the device, query record function is provided.
Sys Info: To check the current device‟s saving status, its version information and so
on.
11
2. User Management
2. User Management
The user‟s basic information on the device includes fingerprint, password and card.
In company‟s attendance management, for employee‟s change, the information on
the device also needs modification. Therefore, operations including Add, Delete,
Edit and so on can be done on the device.
2.1 Add a New User
Firstly, enroll employee‟s fingerprint or password in the device.
Enter [New user] interface:

Note: Only some models have card enrollment option.
AC.NO: Staff's attendance number.
12
2. User Management
Name: Input user‟s name with T9 input method.
FP (Fingerprint): Enroll employee‟s fingerprint. Ten fingerprints can be enrolled at
most.
The employee with fingerprint enrolled can use fingerprint to record attendance.
PWD (Enroll password): Enroll user‟s password. The effective digit is 1-8. The
employee with password enrolled can use password to record attendance.
Card: Registered staff's Card, only the registered card is possible to check
attendance.
Privilege: Users are people whose identity must be authenticated before enter a
menu. The ordinary consumer can track attendance by the card or the password only;
the manager already may equally carry on the daily checking attendance with the
ordinary consumer, but may enter the menu to operate each option.

Note: When there is no administrator, any person may enter the main menu
and operate; after the administrator is enrolled, no one can enter the main
menu until the administrator confirmed.
For example: the following is the flow for Add user.
1. Input User ID
1) Allocate User ID by default.
2) Press “
” to delete the allocated User ID by default. Input User ID from
keyboard. If the User ID is wrong, press “
” and input it again.
2. Input name
Use T9 input method to input employee‟s name.
Press OK or ▲/▼ to select “Enroll fingerprint”, then press OK to start fingerprint.
3. Enroll fingerprint
13
TFT Serials User Manual
Press finger according to device‟s prompt. Press the finger three times in the proper
way.
If one fingerprint is enrolled successfully, press OK to continue another finger, then
press menu and ESC to return the previous interface.
Press ▲/▼ to select “Enroll password” and press OK to enroll password.
4. Enroll password
Input password (1-8) according to the prompt, and press OK to verify it. Then press
OK save it or press ESC to exit without saving it.
After saving,
signal will be on the device, which means the password has been
set.
5. Enroll cards ★
Scroll ▲/▼keys to locate the cursor on “Enroll card" button, and press "OK" to
enter the card registration.
14
2. User Management
Slight ware the card near the sensor area, after the equipment found the card number,
press OK key to save, press ESC to give up, then remove the card from the
equipment, after the "Enroll successfully" the card number will display on the
register button.
6. Privilege setting
Scroll the▲/▼ key and local cursor on the "Privilege" option box, scroll
/
key
to choose privilege.
7. Save/exit user registration
To confirm the registration information is correct, after getting confirmation, save it.
The way for saving:
1) Scroll ▲/▼ key to locate cursor on the "OK (M/<-)"button, please press "OK"
key again, the prompt "Change saved! Continue?” on the equipment, press "OK" the
key to continue, otherwise, press ESC to exit.
2) Press the ESC key or scroll ▲/▼key to locate the cursor on the "Back
(ESC)"button, please press "OK" key again, the prompt "Do you want to save
changes" appear on equipment, press "OK" key to save and return to the previous
interface, does not save and return to the previous interface, press ESC key.
2.2 User Management
All users‟ information saved in the current device can be queried in User
Management, including user name, fingerprint count, whether to enroll password or
15
TFT Serials User Manual
card, user attendance record and so on. Editing or deleting user can also be done
here.

Note:
1)
Means this employee is the administrator.
enrolled.
Means password has been
Means ID card has been enrolled.
2) The picture may be different from your device. The real product prevails.
Press menu on the above interface, and the operating menu will pop out:
Press ▲/▼ to select the item.
2.2.1 Search User
If many users are enrolled, in order to find an employee quickly, the device has
provided “User ID” to search the employee.
Press menu on manage user interface to get operating menu. Select “Search user”
or press any numeric key to enter the following page:
16
2. User Management
Input User ID of employee to be queried. Press OK, after successful query, the blue
cursor will point to the employee. If there is no such employee, “no enrolled data”
will appear.
2.2.2 Query Attendance Record
When administrator is checking employee‟s fingerprint and other enrolled
information, he can also check the employee‟s attendance record during that month.
Press menu on user management interface to get the operating menu, select
“Record”, and the employee‟s monthly attendance record can be checked:

Note: The picture may be different from your device. The real product
prevails.
Press ▲/▼ to read attendance record.
Press OK for detailed information.
17
TFT Serials User Manual
Then press ESC to return to user management interface.
2.2.3 Edit User
Edit user information saved in the device. For example, the former enrolled
fingerprints are unusable, enter “edit user” to re-enroll fingerprint, password or card.
Use ▲/▼ or search user on user management interface to select employee to be
edited. Then press menu to select “edit” or press shortcut to verify it, and all
enrolled information can be displayed on the device:

Note: Only some models have name and card options.
User ID cannot be modified. The operation is similar to that of add user. Fingerprint
can be re-enrolled. Click “enroll password” directly to set password or modify
password. The access can also be modified.
Save edition/exit edition
18
2. User Management
1) Press menu or ▲/▼ to select [M/<-], press OK, save edition and return to user
management interface.
2) Press ESC or ▲/▼ to select ESC and then press OK, and the device will prompt
“Do you want to save changes?” If you want to save it, press OK and return to the
previous interface. Or press ESC to return the previous interface directly.
2.2.4 Delete User
“Del user” is to delete employee‟s partial information or all information from the
device. It is used when the following states happen:
1) When fingerprint or password of the employee is not needed any more.
2) When employee leaves the position.
Press ▲/▼ on user management interface or use search user to select the
employee to be edited. Click menu to get operating menu, and then select “delete
user”.
Delete user:

Note: Only some models have Del ID Card Only options.
If the user has no fingerprint or password, the corresponding item is blue and cannot
be operated. Press ▲/▼ to select the item to be operated. Press OK to pop out
dialog box and verify whether to delete this item or not. Then the device will give
corresponding prompt. Press ESC to return to user management interface.
19
TFT Serials User Manual
2.2.5 Add User
In order to add user conveniently for operator, Add user is configured here. The
function is the same as that in 2.1 Add a New User.
2.3 SMS
The operator can edit the SMS content in advance and make it displayed on the
screen. SMS includes common SMS and individual SMS. If a common SMS is set,
the SMS figure will be displayed in information column at the bottom of standby
interface in specified time. You can press the shortcut (can be set in 4.4 Keyboard
Definition) to check the SMS content. If individual SMS is set, the employee who
can receive SMS can see SMS after successful attendance.
Operation

Note: The picture may be different from your device. The real product
prevails.
Press ▲/▼ to read SMS.
Press “page down & page up” to read SMS.
Press OK to query detailed information.
Press Menu to get SMS setting menu.
20
2. User Management
2.3.1 Set SMS
1)Add SMS
Press ▲/▼ in pop-up menu, select “New” to add a new SMS.
Start time: The time when SMS comes into effect
Effective time length: SMS appears in the effective time. After the effective time, it
won‟t appear.
Information type:
Individual: SMS aimed at individual only.
Public: SMS able to be seen by all employees.
Reserved: Preset SMS, no difference of individual SMS or common SMS.
Operation:
When the cursor is on the text box, you can press the shortcut to enable T9 input,
and input SMS content. Press ▲/▼ to switch option input box. You can press
/
to change setting or press numeric key to input value.
(1) If the selected type is individual SMS, Assign is enabling. Here, it is to distribute
individual SMS to employee:
21
TFT Serials User Manual
Press ▲/▼ to search employee.
Press “page down & page up” to search employee.
Press OK to select the employee, and SMS will be distributed to him.
Press menu to save it and then exit.

Note: If exit without selecting any employee, the SMS type will become
reserved.
(2) If the selected type is common SMS or preset SMS, distribute cannot be used.
After setting, press menu to save it and return to SMS list.
2) Edit SMS
Press ▲/▼ in pop-up menu to select “Edit”, and SMS can be edited.
The operation is the same with that of Add SMS.
3) Delete SMS
Press ▲/▼ in the pop-up menu to select “Delete”, and the selected SMS can be
deleted. At the same time, all information related with this record can be cleared.
2.3.2 Employee Check SMS
1) Check common SMS
When the device is in standby state, the main interface will display pictures and
current effective common SMS content in cycle. The display time interval is the
same with that of picture display.
22
2. User Management
When
appears on main interface of the device, press shortcut (defined in 4.4
Keyboard Definition) to check current effective common SMS in time.
2) Check individual SMS
When user passes verification, if the user has SMS, the SMS content will be
displayed.
23
TFT Serials User Manual
The information display time length is 30 seconds. During this period, user
verification can be done. Close the current display to enter verification interface.
24
2. User Management
2.4 Card Management ★
Support Mifare non-touch intelligent card with working frequency of 13.56MHZ.
Integrate fingerprint attendance to other systems and support multi-verification
mode to meet the demands of different people.
Operation:
Press ▲/▼ to select your desired item, press OK to execute the current selected
item.
2.4.1 Enroll Card
Use Mifare card as ID card. Only card number is needed to enroll.
Operation:
1. Enrollment
Step 1: Select Enroll ID Card and then press OK.
25
TFT Serials User Manual
Step 2: Press keyboard to input the number to be enrolled (if the number has been
there already, the device will prompt you to copy the information to the card), and
then press OK.
Step 3: The device prompts to punch card.
Step 4: Put the card in the sensor area until the operation is successful.
2. Verification:
Punch the card in the sensor area. After the device reads the card, move the card
away. When the verification is successful, the device will give prompt.
2.4.2 Enroll Fingerprint Card
Enroll fingerprint and write fingerprint into card.
Operation:
1. Enrollment
26
2. User Management
Step 1: Select Enroll FP Card and press OK.
Step 2: Use keyboard to input the number to be enrolled (if the number has been
there already, the device will prompt you to copy the information to the card), and
then press OK. The device will prompt you to press your finger.
Step 3: Press finger properly for three times.
Step 4: Device prompts “Punch Card”.
27
TFT Serials User Manual
Step 5: Put the card in the sensor area, waiting for the device to read fingerprint data
into card until the enrollment succeeds.
2. Verification:
Punch the card in the sensor area. After the device reads the card, move the card
away. When the verification is successful, the device will give prompt. If the pressed
fingerprint is different from that stored in the card, the verification will fail.
2.4.3 Clear Card Information
Delete all the information in the card being operated at present.
Operation:
Select Erase Card Info and press OK. Put the card in the sensor area, waiting for
device to delete all the information in the card. If the card data has been stored in the
device, the device will remind you whether to delete the information in the device or
28
2. User Management
not. “Yes” is to delete the user‟s fingerprint and information in the device. “No” is to
keep the information.
2.4.4 Copy Card Information
Copy card information to the device (after that, the fingerprint is still in the card),
then press fingerprint attendance directly on the device, with no need of using
card.
Operation:
Select Copy Card Info and press OK. Press ▲/▼ to select copy “User Info” or
“User Info && FP”, and then press OK.
2.4.5 Card Setting
Set password of Mifare card and decide whether the information should be saved or
29
TFT Serials User Manual
not.
Only Verify ID: Verify the user as ID card verification.
Fingerprint Card Password: After the password is set, the device will write
password into the enrolled fingerprint card. Then the fingerprint card can only be
used on this device.
Must Save Information: When you enroll the card or fingerprint card, save the
enrolled information in the device or not. “No” means the information is only saved
in the card. “Yes” means the information is saved in both card and device.
Operation:
Press ▲/▼to move cursor to the item to be set. If it is the input box, press numeric
keys on keyboard to input the value. If it is the roll box, press
/
button to
switch the values. After setting, press OK directly to return to the previous interface.
Press ESC to cancel setting and return to the previous interface.

Note: Card sensor area is 3cm-5cm above fingerprint reader.
30
3. Communication Settings
3. Communication Settings
When the device and computer are used to transmit data, it is necessary to use
communication wire to set communication parameters in the device. When the
device is in communication, “communicating…” appears. Don‟t operate the device
then.

Note: When the device is communicating with computer, please check the
setting here. The parameters here must be in accordance with that of software
communication interface.
3.1 Network Option
When Ethernet is used for communication of device and computer, the following
settings need to be checked:
Device IP address: IP is 192.168.1.201 by default. You can modify it if it is
necessary. But it cannot be the same with that of computer.
Subnet mask: It is 255.255.255.0 by default. You can modify it if it is necessary.
Gateway address: It is 0.0.0.0 by default. If the device and computer are in
different net segment, it is necessary to set address.
DNS Server: Set the DNS Server for the communication.
Net speed: Set the speed according to the LAN where the device is.
31
TFT Serials User Manual
Operation:
Press ▲/▼to move cursor to the item to be set. If it is the input box, press numeric
keys on keyboard to input the value. If it is the roll box, press
/
button to
switch the values. After setting, press OK directly to return to the previous interface.
Press ESC to cancel setting and return to the previous interface.
3.2 Serial Port Option
When serial port (USB) is used for communication of device and computer, the
following settings need to be checked:
Baud rate: Used for communication with computer. There are five options: 9600,
19200, 38400, 57600 and 115200.
USB: Whether use USB to communicate. Select “ON” if USB is to be used.
Set RS232 and RS485 to OFF when you need to use USB communication.

Note: Only some models have USB communications.
Operation:
32
3. Communication Settings
Press ▲/▼to move cursor to the item to be set. Press
/
button and choose the
values. After setting, press OK directly to return to the previous interface. Press ESC
to cancel setting and return to the previous interface.
3.3 Connection Option
When USB is used for communication of device and computer, it is necessary to set
device ID.
Device ID: 1-254. If USB is used, this ID needs to be input on the software
communication interface.
To improve the security of attendance data, connection password needs to be set
here. Connection password must be input when computer software is to connect
device to read data.
Connection password: System password is 0 by default (namely, there is no
password), it can be set as other value. After setting, the password must be input if
software is to communicate with device. Or the connection will fail. The password
length is 1-6 digits.
Operation:
33
TFT Serials User Manual
Press ▲/▼ to move cursor to the input box. Press numeric key on keyboard to input
the value. After setting, press OK directly to return to the previous interface. Press
ESC to cancel setting and return to the previous interface.
3.4 Wireless Option ★
Before the device is used for wireless network, other physical groupware of 802.11
networks, such as joint, distributing system, wireless medium must be in existence.
ESSID to connect to the network must be known (network ID).
Network ID: Network ID to be connected to wireless network. (There is difference
between small letter and capital letter.)
Network model: there are two models: infrastructure model (for star structure) and
ad-hoc model (for peer-to-peer-network).
Authentication mode: Infrastructure mode includes five authentication modes:
OPEN, SHARED, WEPAUTO, WPAPSK and WPA2PS002E.
Ad-hoc model: Include four authentication modes: OPEN, SHARED, WEPAUTO
and WPANONE.
Encrypt type: when the selected encrypt type is NONE, the password in WEP
(Wired equivalent privacy) and WPA (WiFi protested access) cannot be edited,
namely, it is not necessary to input password.
Device IP address: In 802.11 wireless networks, there is DHCP. Or enter IP
interface to input correct IP address, subnet mask and so on.
34
3. Communication Settings
Operation:
Press ▲/▼ to switch cursor to the input box or button. Use T9 input to input
network ID, which must be input, or the cursor cannot be moved to other input box.
Press
/
button to select the item you need to set, and then press [M/OK] to do
the corresponding operation.
1) Set password:
According to the selected authentication mode and different encrypt types the
interface where password is set is also different. There are two interfaces: WEP and
WPA.
WEP password:
Input correct password. There are four passwords in WEP password. If the four
passwords are set properly, only the current selected password is the effective value.
35
TFT Serials User Manual
WPA password:
Input correct password, set password, press [M/OK] to save the setting, and then
return to wireless option interface.
2) Specify IP:
Specify the device IP in wireless network. It has nothing to do with network option
in communication option.
After IP is specified, press OK to save the setting, and then return to wireless option
interface.
After setting, press OK directly to return to the previous interface. Press ESC to
cancel setting and return to the previous interface.
Otherwise, user can use the WIFI Software in the device accessory CD-ROM to set
the parameters. For details, please refer to Appendix 10.11 WIFI Software Using
Instructions.
36
3. Communication Settings
3.5 Wireless Network ★
Check wireless signal and the signal intensity received in the current environment to
create condition for user to select better network.
Press M/OK to set the selected wireless network. Press
to refresh the list.
37
4. System Option
4. System Option
Set system parameters to meet user‟s demand as much as possible.
4.1 System Parameter
1: 1 matching threshold value: The similarity of ID + fingerprint verification and
the enrolled template
1: N matching threshold value: The similarity of verification and the enrolled
template
Recommended matching threshold value:
FRR
high
FAR
low
Matching threshold value
1:N
1:1
45
25
middle middle
35
15
low
25
10
high
Date format: Time format displayed on the initializing interface of fingerprint
reader.
Press
/
button to select the format you need to set. The fingerprint reader
supports ten date format: YY-MM-DD, YY/MM/DD, YY.MM.DD, MM-DD-YY,
38
4. System Option
MM/DD/YY,
MM.DD.YY,
DD-MM-YY,
DD/MM/YY,
DD.MM.YY
and
YYYYMMDD. Select your desired date format.
Key beep: Press
/
to set whether the key has voice or not. “Yes” means having
voice, and “No” means no voice.
Sensitivity: Set the sensitivity of the FP sensor.
Voice prompt: Press
/
to select whether to give voice prompt or not. The
device will give corresponding voice prompt during operation.
Volume: Press
/
to set it.
Alg Version: Select to use 9.0 or 10.0 algorithm version.
Recheck Minutes: It is in the set time range (unit: minute). If somebody‟s attendance record
has been there, then the record of second attendance won‟t be saved (effective value is
0-60 minutes. 0 means all the records after verification are saved).
Log Alert: After the free time period reaching this value, the device will trigger
alarm automatically (effective value is 0-99, 0 means the space is all used and there
is no alarm).
Operation:
Press ▲/▼ to move cursor to the input box. If it is the input box, press numeric keys
on keyboard to input the value. If it is the roll box, press
/
button to switch the
values. After setting, press OK directly to save the setting and return to the previous
interface. Press ESC to cancel setting and return to the previous interface.
39
TFT Serials User Manual
4.2 Data Management
Delete Attlog: Delete all attendance records.
Delete All: Delete all enrolled employees‟ information, fingerprint and attendance
record.
Clear Purview: Change all administrators into common users.
Delete Picture: Delete all user uploaded pictures in the device.
Operation:
Press ▲/▼ to move cursor to the selected button. Press OK to start operation. The
device will remind you whether to continue the current operation or not. Then press
OK to delete all the data, which won‟t be recovered after deletion. Press ESC to
return to the previous interface.
Delete Picture: Clear the propaganda pictures uploaded to the device from U disk or
SD card (Refer to 6 U Disk Management for how to upload the propaganda
pictures).
Operation:
40
4. System Option
Press “▲/▼” to preview the propaganda pictures in the device. Click OK to delete
all these pictures. After deletion, the next picture will appear. Click “Delete all” to
delete all the propaganda pictures in the device. Then press ESC to return to Data
Management interface.
4.3 Upgrade Firmware
Update the firmware by utilizing the USB Pen Drive (flash drive)

Note: If you need such upgrade file, please contact our technician. Usually,
firmware upgrade is not recommended.
Operation:
Insert U disk with upgrade file into the USB slot. The device will identify the file
automatically. The device will give prompt whether it is successful or not.
4.4 Keyboard Definition
User defined the device‟s attendance status key. Press corresponding status key to
record attendance.
Press any status key on the standby interface, and the attendance status and status
key will be displayed at the left bottom of the screen.
Operation:
41
TFT Serials User Manual
Press ▲/▼ to read shortcut definition.
Press OK to edit the selected shortcut.
4.4.1 Set Shortcut
Select a shortcut, press OK to enter edit interface.
Function: Set shortcut function for his key, including status key and view SMS.
The following options will appear after the status key is selected:
Code: Allocate a code for status key to provide convenience to check the record
statistics.
Name: The name of key status.
Auto switch: When it reaches the set time point, the device will switch the
attendance status automatically.
1) Set it as function key
Operation:
42
4. System Option
Press
to set “Backspace” as view SMS.
/
2) Set it as status key
Press ▲/▼ to move cursor to the input box. Press numeric key on keyboard to input
the value. After setting, press OK directly to save the setting and return to the
previous interface. Press ESC to cancel setting and return to the previous interface.
4.4.2 Use Shortcut
1) Status key
Press
key on standby interface and the corresponding status will appear at the
left bottom.
43
TFT Serials User Manual
2) Shortcut key
Set “0” as view SMS in setting.
Press “0” on standby interface to enter the interface of SMS.
4.5 Interface Option
1:1 Match Retry Times & Password Retry Times: When user is using 1:1 match
or password verification, he may forget to enroll fingerprint or does not press the
finger in the proper way. For user‟s convenience and to reduce repeat key, the device
allows retry. User can set initializing interface‟s display style.
Clock Mode: After verification, the selected clock mode will be displayed on the
screen.
Display propaganda picture: User can display some propaganda pictures on the
screen.
44
4. System Option
1) Picture cycle interval means how soon the picture will be changed (effective
value is 3-999 seconds.)
2) Time display delay means the clock picture display time length after verification.
After the display delay, the propaganda picture will be displayed on the initializing
interface again (with effective value of 0-999 seconds, and 0 means displaying clock
all along).
Operation:
Press ▲/▼ to move cursor to the input box. Press numeric key on keyboard to input
the value. After setting, press OK directly to save the setting and return to the
previous interface. Press ESC to cancel setting and return to the previous interface.
4.6 Reset
Make device‟s communication option, system option and so on reset to the state of
factory.
Reset All Default Setting: Make all the parameters in the device reset to the state of
factory.
Reset Keyboard Definition: Reset the corresponding setting of keyboard definition
to that of factory.
Reset Bell Setting: Only reset bell option to factory state.
Reset Other Parameters: Only reset communication option, system parameter and
interface option and so on to factory state.
45
TFT Serials User Manual
Press ▲/▼ to move cursor to the button to be operated. Press OK to start operation.
The device will say “Are you sure?” Press OK to reset it to factory state and press
ESC to cancel operation.

Note: The employee‟s information and attendance data won‟t be deleted when
this operation is being done.
4.7 Bell Option
Many companies need bell for on-duty and off-duty. Some use manual bell. Some
use electronic bell. To save cost and provide convenience for management, we
integrate bell functions to fingerprint reader. You can set time for bell. When it is the
scheduled time, the fingerprint reader will play the selected ring automatically. And
the ring will stop automatically when it is the end time.
Operation:
46
4. System Option
Press ▲/▼ to read bell option.
Press OK to set the selected bell and edit the bell.
Bell time: The bell rings automatically when it is the specified time.
Music: Bell ring.
Volume: ring volume.
Times: Ring times.
State: Whether to enable this bell.
Press ▲/▼ to move cursor to the input box. Press numeric key on keyboard to input
the value. After setting, press OK directly to save the setting and return to the
previous interface. Press ESC to exit.

Note: Ring time can be set with week as the period, namely, the bell rings
automatically at some time of some day in a week. The External bell is not
the must configuration. If you want it, please contact our businessman or
technician.
4.8 Other Options
Set sleep time, external bell and other parameters for the device.
Sleep Time: When it is the scheduled sleep time, the device not in operation will
enter sleep status. Press any key or finger to awake it.
Fingerprint Image: Select whether to display the fingerprint image on the screen
when it is enrolling or verifying there are 4 options: display upon both enrollment
47
TFT Serials User Manual
and verification, only display upon enrollment, only display upon verification, not
display upon enrollment and verification.
Power Button: To prevent hostile power-off, select whether to lock power-off or
not.
Key Position: Choose the display position of the keyboard input.
Beep Position: Choose the beep position.
Operation:
Press numeric key on keyboard to input the value to be set. After setting, press OK
directly to save the setting and return to the previous interface. Press ESC to cancel
the setting and return to the previous interface.
48
5. Time Date
5. Time Date
5.1 Time Date Option
Accurate attendance time is based on accurate time date.
Enter Date/Time to set options:
Operation:
Press ▲/▼ to move cursor to the input box. Press numeric key on keyboard to input
the value. After setting, press OK directly to save the setting and return to the
previous interface. Press ESC to cancel setting and return to the previous interface.
5.2 DLST
DLST, also called Daylight Saving Time, is a system to prescribe local time in order
to save energy. The unified time adopted during the system date is called “DLST”.
Usually, the time will be one hour forward in summer. It can make people sleep
early and get up early. It can also reduce lighting to save power. In autumn, the time
will be recovered. The regulations are different in different countries. At present,
nearly 110 countries adopt DLST.
To meet the demand of DLST, a special option can be customized on our RF Card
Time & Attendance recorder. Make the time one hour forward at XX (minute) XX
(hour) XX (day) XX (month), and make the time one hour backward at XX (minute)
49
TFT Serials User Manual
XX (hour) XX (day) XX (month) if necessary.
Operation:
1) Set DLST as “ON”.
2) Input DLST start time and end time.
For example, if 08:00, April 1st is set, the device enter DLST, and the time will be
one hour forward. If it is 08:00, August 1st, the device will reset normal time.
3) Press OK to save setting. Press ESC to exit without saving.
50
6. U Disk Management
6. U Disk Management
Import user information, fingerprint template, attendance data and so on in the
device to attendance software or import user information and fingerprint to other
devices through U disk or SD card.
6.1 Download by U-disk
1. Download attendance data
Save all attendance data in the device to U disk.
Operation
1) Insert U disk into USB slot of the device.
2) Press “▲/▼” to Download Attlog.
Press OK for verification. “Downloading, wait…” will appear on the display when
the device is downloading attendance data until it is successfully downloaded.
3) Press ESC to return to initializing interface. Pull out U disk. X_attlog.dat
(attendance log) will be saved in U disk. (X stands for device ID).
2. Download user data
Save all users‟ information and fingerprint in the device to U disk.
Operation:
Insert USB flash disk into USB slot of the device, press “▲/▼” to download user,
51
TFT Serials User Manual
then user.dat (user information) and template.dat (fingerprint template) will be saved
in U disk.
3. Download SMS
Save SMS added in the device to U disk.
Operation:
Insert U disk into USB slot of the device. Press “▲/▼” button to select download
SMS. After successful download, udata.dat and sms.dat can be seen in U disk.
4. Download Photo
Save user photo in the device to U disk.
Operation:
Insert U disk into USB slot of the device. Press “▲/▼” button to select download
Photo. After successful download, the user photo will can be seen in U disk, as the
format of userID.jpg.
6.2 Upload by U-disk
1. Upload user data
Upload user information and fingerprint saved in U disk to device.
Operation:
Insert U disk into USB slot of the device. Press “▲/▼” to select upload user data,
and then press OK, and user.dat (user information) and template.dat (fingerprint
template) in U disk will be uploaded to the device. If there are no such files, “data
copy error” will appear.
2. Upload SMS
Upload SMS in U disk to the device.
Operation:
Insert U disk into USB slot of the device. Press “▲/▼” button to select upload
SMS and then press OK. Udata.dat and sms.dat will be uploaded to the device.
3. Upload photo
Upload user photo in U disk to the device.
52
6. U Disk Management
Operation:
Insert U disk into USB slot of the device. Press “▲/▼” button to select upload
Photo and then press OK. The user photo named as userID.jpg will be uploaded to
the device.
4. Upload user defined picture
Upload JPG picture started with “ad_” in U disk to the device. Then this picture will
be displayed on the initializing interface (Refer to Appendix 10.6 Propaganda
Picture Upload Rules).
Operation:
Insert U disk into USB slot of device. Press “▲/▼” to preview the pictures of U
disk. If you want to upload the picture, click OK. Then the next picture will appear
automatically. After upload, press ESC to exit.
6.3 Download to SD Card
1. Download attendance data
Save all attendance data in the device to SD card.
Operation
1) Insert SD card into SD card slot of the device.
2) Press “▲/▼” to Download Attlog.
Press OK for verification. “Downloading, wait…” will appear on the display when
the device is downloading attendance data until it is successfully downloaded.
3) Press ESC to return to initializing interface. Pull out SD card. X_attlog.dat
(attendance log) will be saved in SD card. (X stands for device ID).
2. Download user data
Save all users‟ information and fingerprint in the device to SD card.
Operation:
Insert SD card into SD card slot of the device, press “▲/▼” to download user, then
user.dat (user information) and template.dat (fingerprint template) will be saved in
SD card.
53
TFT Serials User Manual
3. Download SMS
Save SMS added to the device to SD card.
Operation:
Insert SD card into SD card slot of the device. Press “▲/▼” button to select
download SMS. After successful download, udata.dat and sms.dat can be seen in
SD card.
4. Download Photo
Save user photo in the device to SD card.
Operation:
Insert SD card into SD card slot of the device. Press “▲/▼” button to select
download Photo. After successful download, the user photo will can be seen in SD
card, as the format of userID.jpg.
6.4 Upload by SD Card
1. Upload user data
Upload user information and fingerprint saved in SD card to device.
Operation:
Insert SD card into SD card slot of fingerprint reader. Press “▲/▼” to select upload
user data, and then press OK, and user.dat (user information) and template.dat
(fingerprint template) in SD card will be uploaded to the device. If there are no such
files, “data copy error” will appear.
2. Upload SMS★
Upload SMS in SD card to the device.
Operation:
Insert SD card into SD card slot of the device. Press “▲/▼” button to select upload
SMS and then press OK. Udata.dat and sms.dat will be uploaded to the device.
3. Upload photo
Upload user photo in SD card to the device.
Operation:
54
6. U Disk Management
Insert SD card into SD card slot of the device. Press “▲/▼” button to select upload
Photo and then press OK. The user photo named as userID.jpg will be uploaded to
the device.
4. Upload user defined picture
Upload JPG picture started with “ad_” in SD card to the device. Then this picture
will be displayed on the initializing interface. (Refer to Appendix 10.6 Propaganda
Picture Upload Rules)
Operation:
Insert SD card into SD card slot of device. Press “▲/▼” to preview the pictures of
SD card. If you want to upload the picture, click OK. Then the next picture will
appear automatically. After upload, press ESC to exit.
55
7. Auto Test
7. Auto Test
The device can test various modules automatically to help operator to judge the
module with fault quickly. Auto test include TFT Test, Audio Test, Keyboard Test,
Sensor Test and RTC Test.
Press “▲/▼” to select the item. Press OK to start it.
7.1 TFT Test
The device can automatically test TFT color display effect through color display
(white display and black display), to see whether the screen works normally.
Press OK to continue and press ESC to exit.
7.2 Audio Test
The device can automatically test voice prompt effect through playing voice files in
the device to see whether the files are complete and the voice effect are good or not.
Press OK to continue and press ESC to exit.
7.3 Keyboard Test
The device can automatically test various keyboards to see whether the keys work
normally or not.
Press any keyboard on the test interface (except for OK and ESC) to check whether
56
7. Auto Test
the pressed keyboard is in accordance with that displayed on the screen.
Will appear when it is the right key, and
will appear when it is not the
right key.
Press ESC to exit.
7.4 Sensor Test
The device will automatically test the FP reader to see whether it works normally.
Press fingerprint to see whether the image is clear and usable.
Press fingerprint on the reader window and the fingerprint image will appear on the
screen.
Press ESC to exit.
7.5 Real-time Clock
The device can automatically test the clock to see whether it works normally.
Press OK to start time and then press OK to stop time.
Press ESC to exit.
57
8. Query Record
8. Query Record
Employee‟s attendance records will be saved in the device. For convenience, query
record function is provided.
According to user‟s input query condition, the record will be displayed on the screen
for user to check.
Enter Record, input corresponding information in the query condition input box.
1) When the User ID is blank, all employees are inquired.
2) When input a User ID, only this employee‟s attendance record can be queried.
After query, the records in accordance with the conditions will be displayed on the
screen:
Press “▲/▼” to move the cursor to the line to be queried. And press OK to check
58
8. Query Record
attendance record.
For example, the detailed attendance information of employee 27 on May8th as
follows:
At the bottom of the screen, there are some remark, and the capital letters with their
meanings:
Verification:
F: Means Fingerprint verification
P: Means Password verification
C: Means ID card verification
Status:
It is the attendance status. The code displayed in the list is the status code. And
status name will be displayed in the information column.
59
9. System Information
9. System Information
Use system information to check the current device‟s saving status, its version
information and so on.
9.1 Record Capacity
Display the count of enrolled users, administrator, password enrollment, the current
enrolled fingerprint and the current saved attendance record. Also display the
capacity of the fingerprint and attendance record, as show below:
9.2 Device Information
Display device name, serial number, version information, and vendor and
manufacture date in device information for check.
60
10. Appendix
10. Appendix
10.1 Keyboard
Different device has different kinds of keyboard, and the function of the keyboard is
different. Please check the fallows:
Key
Numeric
Function
1. 0~9,used to input employee number, password and so on.
key
2. 0 on manage user interface is shortcut of “search user”.
▲
1. Upward.
2. Shortcut.
▼
1. Downward.
2. Shortcut.
*/
1. Modify current item value.
2. Shortcut.
3. Enable T9 input.
4. Switch input method in T9 input.
/
1. Modify current item value.
2. Space back. Press it when User ID, password, and system value are
input incorrectly to delete the wrong value and input the value
again.
3. Shortcut.
0/
1. Power-off.
Press it on the initializing interface for 3 seconds to
enter power-off count down state.
2. Shortcut.
M/OK
ESC
Menu, OK
1. Cancel the operation and return to the superior menu.
2. Close T9 input.
61
TFT Serials User Manual
10.2 USB
1. USB Host
The device will may be used as USB Host to exchange data with external U disk.
The data transmission speed is quick, the traditional fingerprint machine only
supports the RS232, RS485 or Ethernet way data transmission, when as a result of
physical condition limit, data quantity big, and the data transmission cost quite long
time. But the USB data transmission is more quick than the former any transmission
mode, may complete downloading data by U disk in a short period of time, like this
greatly enhances the efficiency.
The operational steps of the device as USB Host please refer to the manual 6. U disk
Management detailed briefing.
2. USB Client ★
The device will be as removable storage devices and the data in the device will
transfer to a computer via connected USB cable.
When the device is an USB Client, the Communication Option will have USB
communication options. For more details please refer to 3. Communication Settings.
10.3 Time Ring
In many factories, ringing apply to broadcast message to inform employee their duty
are on or off, and the traditional way is to ring bell by manual or special electron
machine. We have already embedded the time ring module into the fingerprint T&A
system, you may benefit from the low cost and convenience management. There are
more two options that is Bell schedule and Bell duration in the device bell ring
provide with. The system total has eight Bell schedule to set, according to actual
need you may set time bell, when the time arrive at the appointed time, the device
will automatically ring bell, the duration of ringing achieve assigned hour, the
ringing will stop automatically.
There are two to ring bell:
62
10. Appendix
1) Send sound from the speaker of device.
2) ★Connect the external electrical bell to the device, when arrive the appointed
time, the device will send signal to trigger relay.
10.4 T9 Input Method
The name of T9 input method is the smart input method; it is famous for highly
effective and quickly inputting the character, this equipment fully supports the T9
Chinese, the T9 English, and the symbol input. There are three or four English
letters on 0-9 numeric keyboards of the machine, for example the numeric keyboard
1 has the A, B, the C three letters, only input key where this letter locate for the T9
Chinese, Press the algorithm of the program will automatically combine the
legitimate Pinyin. Then press the numeric key to choose Pinyin for inputting the
Chinese character. The T9 English also comply with the letter arrangement of
English word to input, only press key which inputs this letter, the program
automatically display this key expressed all letters, press the numeric key to select
letter. The T9 input method also may input some marks. May input the name, the
short message content through the T9 input method user is able to input the name,
the short message content.
T9 Chinese character input (take “Angel” for example):
Press
to enter T9 input. And press
to shift input method of Pinyin, English
and Symbol, and then select English.
Input “2” to get the first
letter and press “3” to „A‟.
63
TFT Serials User Manual
Use the same method to input
the other letters “ngel”.
Press ESC to exit
64
10. Appendix
10.5 Quick Query of Attendance Record
It is used for common user to query his intraday attendance record to see whether
there is something wrong for attendance time and notify administrator the abnormal
recorder in time.
Operation
Press OK to display the employee‟s intraday records after successful fingerprint or
password verification in 10 minutes.
For example: the employee with User ID of 1 can check his intraday attendance
record by pressing OK after fingerprint verification.

Note: The picture may be different from your device. The real product
prevails.
Press ▲/▼ to read attendance record.
Press OK to query detailed information.
Press ESC to return to initial interface.
10.6 Propaganda Picture Upload Rules
1. The picture format must be JPG. Other formats are not accepted here.
2. The file name of propaganda picture must be ad_0-ad_9, for example ad_1.Jpg.
3. The file name won‟t be changed after it is uploaded to the device. If it is necessary
to change this picture, upload another picture with the same file name to cover it.
65
TFT Serials User Manual
4. Every picture cannot be over 20K, or it cannot be uploaded.
5. The picture‟s resolution is 400 wide and 240 high. It is better not to be more or
less than it.
6. The propaganda pictures‟ count should be 10 at most.
10.7 Short Message Management
Our some product provide a function which can send a message to assigned person
through public to person way, We only need use the back-end software to set it, then
upload it to the fingerprint machine, , as long as the attendance dive start the for
public short message will be seen on machine screen, and it will show for ever, for a
person short message will not display until the user‟s fingerprint verification is
positive, Thus reduces the work load to manager the human power , greatly
enhances the working efficiency.
Send a message to a assigned personal, if a staff‟ s birthday is on October 20 , we
may set back-end software to send out a short message to him “ wish your Happy
Birthday” on 20 October , upload it in the machine, after this staff the fingerprint
verify successfully on that day, this message will display on the screen
Send a message to public, if entire company needs to have a meet on June 19, after
we set back-end software to upload the machine, upon this day, the message “holds
XX meet in XX room” will continuously display on the screen, asks everybody
(certainly such information you are allowed to revise according to your need) to XX
participation”
Short message function setting: After setting Short message in the Time&
Attendance software, then upload it to fingerprint machine, the fingerprint machine
support two kind of way to import the short message, which the software connect
with fingerprint machine to import it directly, other way by U flash disk.
Operation Step as follow:
1. Through Time & Attendance software “external program”-> “short message
management” complete to set short message, then connect with the fingerprint
66
10. Appendix
machine and upload it, 2. through Time & Attendance software “ external
program”-> “ short message management” complete to set short message, choose
“ external program”->“U flash disk manage”-> “ export short message”-> “export to
U disk”, after exporting successfully, plug the U disk into the fingerprint machine,
press “Menu” key of the fingerprint machine”-> “Pendri Mng”-> “ Upload short
message”.
Short message function effect: For public short message will be seen and it will
show for ever after this staff the fingerprint verify successfully, this message will
display on the screen.

Note: There is total 1024 items of public for personal short message.
10.8 Mifare Card ★
In order to meet security market need, our fingerprint biometric verification reader
can be embedded EM and Mifare reader module.
Using 125MHZ, 13.56 MHz non-contact smart card technology, these fingerprint
products provide users with new options for supporting multi-authentication of
identity. Combine a non-contact card presentation with a fingerprint biometric. Or,
use a personal identification number (PIN) number along with a non-contact card
presentation. (See multi-authentication).
The fingerprint products provide three levels of fingerprint verification. During the
enrollment process, the LCD prompt will guide the user to place their finger on the
reader. The fingerprint template is collected at the unit and immediately transferred
to the card. During this enrollment process, the fingerprint template is stored on the
card or the fingerprint machine.
During verification at the door, the LCD graphical display will assist the user with
instructions about finger placement on the biometric reader.
For more detail see EM, Mifare Card user Guide.
67
TFT Serials User Manual
10.9 9 Digit Code
When go on enrolling user in the fingerprint machine, along with the standard
enrolling code is five digit(its range is 1-65534), if you need that the enrolling code
is longer in the actual application, we can provide a customized design that the
fingerprint machine own nine digit code.
10.10 Daylight Saving Time
Some device provides correct and current time in any world time period, country or
major city. Accurate adjustments for Daylight Saving Time (or Summer Time) are
made according to each location's rules and laws. No matter what time period a
country or city is located in, this is your top choice for a clock resource site.
This function can be set in the fingerprint machine option, Press Manu key, enter the
option->date time.
In the XX Month XX Date XX minute move forward an hour,
and that in the XX Month XX Date, XX Minute move Back an hour.
The operation refers to this manual 5.2 DLST.
68
10. Appendix
10.11 WiFi Software Using Instruction ★
Step 1:
Wireless End has two options: Active, Disable. If you select the Active item, you
can configure the AP (Access Point). If you select the Disable, you can set the
connection way of the device, and its configuration of IP address.
Step 2:
Full the blank of local Wireless Network ID you want to connect with, this blanket
must be fulfilled.

Note: Must fulfill the blank that is marked with”*”
Step 3:
Wireless Model: there are two options, Infrastructure Model, and Ad-hoc Model,
69
TFT Serials User Manual
click the drop-down box to select the wireless network model, depending on the
different topology of network.
The Infrastructure Model will apply to Hub and Spoke wireless network, it include
five Authentication Type that are OPEN, SHARED, WEPAUTO, WPAPSK,
WPA2PS.
The Ad-hoc Model is used in the peer to peer wireless network. It includes OPEN,
SHARED, WEPAUTO, and WPANONE four type of Authentication Type.
Step 4:
Click the drop-down box to select the Authentication Type.
Step 5:
Click drop-down box to select Encrypt Type. When the item NONE of encrypt
Type is selected, then the password in WEP (Wired equivalent privacy) and WPA
(WiFi protested access) item is not permitted to modify it, it is not need to input
password too.
Step 6:
According to Authentication Type, and Encrypt Type, to input the password,
password complies with the criterion set down by the software.

Note: there are four group passwords in the WEP column, till the all password
have been set up is correct, the current password is valid
Set Connection Parameter:
The device fully support two connection ways, one TCP/IP, anther one is RS 232.
If you select TCP/IP, here the IP and Port value must to be assigned; its value is
same with one in the communication option of the device. Set the option Ethernet in
the device to “Yes”.
If you selectRS232, must configure these parameter, Device ID, COM Port, Baud
rate same with one in the communication option of the device.
Configure the wireless Network IP address:
(1) Click [ConfigMachine] button, the following menu pops up:
70
10. Appendix
(2) Select Config IP Address option, after input IP Address, click the Subnet Mask
input box, and the Subnet Mask will automatically display according to IP Address.
(3) Click OK button, save setting and exit this interface.
After all setting for wireless network is completed, single click SET button on the
MODEMConfigTool interface, the prompt “in working” will appear on the device.
After configure successfully, the corresponding message will inform you, click OK
to close the message and restart the machine, so the configuration change take effect.
10.12 Photo ID Function
Some devices support Photo ID function, which can display user photo saved in U
disk or SD card on the screen as well as User ID, name and so on after verification.
[Operating Step]
1) Create a folder named photo in U disk and store user‟s photo in it.
2) The photo format must be JPG and file name must be User ID. For example, the
name of photo of user whose User ID is 154 must be 154.jpg.
3) Insert U disk into USB slot of fingerprint reader, enter U disk management->
upload data-> upload user photo. The operation is the same with that of 6.6 upload
user defined picture.
4) Enter U disk management->download->download user photo, and a folder named
71
TFT Serials User Manual
photo will be created automatically in U disk. Downloaded user photos are all saved
in this folder.

Note:
1) The name of user photo must not be over 8 digits.
2) When user is verifying, U disk must be inserted into the device all along.
10.13 Backup Battery
The device supports external backup batteries. During removing the battery, be sure
to disconnect the external power supply.
Technical Specifications:
Standard
charged
three
hours
Discharged
time
(reference)
time
Operate
-20℃~45℃
Relative
temperature
more than 4 hours
10%~90%
humidity
Recommended
After fully charged, the battery should be stored under 20±5℃,
storage condition
65%±20%RH
Cycle Life
Charged/discharged cycle for more than 300 times, ≧80% the
amount of capacity
72
10. Appendix
10.14 About the Human Rights Privacy Statement
Dear customer:
First thank you for using Multi-biometric identification product we design and
produce. As one of the global famous fingerprint identification core technology
provider, we are keep carrying on the development and research, also we believe
such action is necessary to: (a) comply with the law or legal process served on Our
company; (b) protect and defend the rights or property of Our company (including
the enforcement of our agreements); or (c) be governed by related law or legal that
involve to the human rights and the privacy in each country.
We are committed to protecting your privacy.
We state as follows:
1. Our civil fingerprints identification equipment merely captures fingerprint
features point, but not the fingerprint image, does not involve and retain privacy.
2. The fingerprint features points are not to be recovered the primitive fingerprint
image, will not involve the privacy.
3. We took an equipment provider, in no event shall we are liable for any direct or
the indirect against legal behavior arising out of use or inability use our equipment.
4. If you have the different dispute for close the human rights or the privacy arising
out of using our equipment, please directly contacts with your employer. Our other
the police fingerprint equipment or the development kit provide with the function
that ability to capture citizen's fingerprint primitive image, as for whether will
constitute the right infringement to you, please contact with the local government or
the equipment final provider as the equipment original producer, we have not any
legal liability for any damage it cause.

Note: There are limited rights to privacy and human rights in the Chinese
Constitution.
The personal dignity of citizens of the People's Republic of China is inviolable and
further, that insult, libel, false accusation or false incrimination directed against
73
TFT Serials User Manual
citizens by any means is prohibited, the protection of freedom of the person and the
residence .The Constitution provides for the freedom and privacy of correspondence
of the citizen.
Finally we hereby stressed that once again, as one kind of advanced identification
technology the fingerprint identification will apply to electronic commerce, bank,
insurance, law service industry in the future, every year, all world cause from the
lack of security password , the humanity are suffering the heavy loss. In under high
safe and secure environment the fingerprint identification protect your status from
damage in fact.
74
10. Appendix
10.15 Environmental Protection
The environmental protection use period marked on our products is the
safety period of our products used under the conditions specified by this
manual without toxic and harmful substances leaking happened.
The environmental protection use period marked on our products does not
include the easy wear and tear components required to be replaced
regularly such as the battery etc. The battery‟s environmental protection use
period is 5 years.
The toxic and harmful substances or element names and the content table
The toxic and harmful substances or elements
Lead
Merc
Cadmiu
Hexavalent
Polybrominated
Polybrominated
(Pb)
ury
m (Cd)
Chromium
biphenyls
diphenyl
(Cr6 +)
(PBB)
(PBDE)
Part name
(Hg)
SMD resistor
×
○
○
○
○
○
SMD capacitor
×
○
○
○
○
○
SMD inductance
×
○
○
○
○
○
SMD diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screw
○
○
○
×
○
○
ethers
○: Indicate that the content of the toxic and harmful substance contained in all homogeneous
materials of this part is in the limitation requirement stipulated in SJ / T 11363-2006.
×: Indicate the content of the toxic and harmful substance contained in at least one homogeneous
material of this part is beyond the limitation requirement stipulated in SJ / T 11363-2006.
Note: The 80% product has adopted the manufacture with non-toxic and harmless environmental
protection materials, the non-toxic and harmless substances or elements instead of the toxic and
harmful substances or elements contained can not be achieved because of the current technology and
economic constraints.
75
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement